Parrot MKI9100 User Manual [no]

PARROT
MKi9100

Quick start guide

Hurtiginstallasjonsveiledning

Käyttöopas

Parrot MKi9100

Installation diagrams........................

English.............................................

Norsk................................................

Suomi...............................................

תירבע................................................

General Information..........................

www.parrot.com

p.04
p.11
p.18
p.25
p.36
p.37

5

www.parrot.com

• A: 12V ignition (orange)

• B: 12V battery supply (red)

• C: Ground

• D: Connection to the vehicle’s power supply

• E : Connection to the vehicle’s speakers

1. Rear right speaker (purple / purple-black)

2. Front right speaker (grey / grey-black)

3. Front left speaker (white / white-black)

4. Rear left speaker (green / green-black)

• F : This wiring is not used.

Not used

6

- Car stereo with an ISO connector

- Bilradio med ISO-tilkobling

- Autoradio ISO-liitännällä

www.parrot.com

• A : 12V ignition (orange)

• B : 12V battery supply (red)

• C : Ground

• D : Connection to the vehicle’s power supply

• E : Line-out 1
1 : Line 1 + : white
2 : Line 1 - : brown

• F : Line-out 2
1 : Line 2 + : red
2 : Line 2 -: black

• G : These wirings are not used

•

A : 12V ignition (orange)

•

B : 12V battery supply (red

)

•

C : Gr

o

und

•

D : Connection to the vehicle’s power supply

•

E : Line-out 1
1 : Line 1 + : white
2 : Line 1 - : brown

•

F : Line-out 2
1 : Line 2 + : re

d

2 : Line 2 -: blac

k

•

G : These wirings are not use

d

Not used

7

- Car stereo with Line In input

- Bilradio med line-in inngang

- Autoradio Line In-sisäänmenoilla

- Inserting the remote control battery

8

- Innsetting av batteriet til fjernkontrollen

- Kaukosäätimen pariston asennus

The remote control only works with a 3V CR2032 battery.

Fjernkontrollen fungerer kun ved hjelp av et batteri av typen 3V CR2032

Kaukosäädintä voi käyttää vain 3V CR2032-tyypin paristolla.

clic

- Do not install the remote

9

control on the outside of the
steering wheel

- Ikke monter fjernkontrollen på
yttersiden av rattet

- Kaukosäätimen asennus
kojelautaan

- Installing the remote control on the dashboard

- Montering av fjernkontrollen på dashboardet

- Älä asenna kaukosäädintä ratin ulkopuolelle

- Installing the screen

- Montering av skjermen

- Näytön asennus

10

This simplified guide of the Parrot MKi9100 gives you the
main instructions to easily use this product. For further
information, refer to the user guide available on our website
www.parrot.com.

Contents

Installing the Parrot MKi9100..............................................

Installing the electronic box.........................................

Car stereo with an ISO connector................................

Car stereo with line-in..................................................

Car stereo without ISO connectors..............................

Installing the kit’s power cable.....................................

Checking the wiring......................................................

Installing the audio connectors....................................

Installing the remote control........................................

Installing the double microphone................................

Installing the screen.....................................................

Using the Parrot MKi9100 for the 1st time.........................

Associating the control unit with the remote control...

Navigating through the menus.....................................

Pairing and connecting a phone to

the Parrot MKi9100......................................................

Using the telephone function..............................................

Synchronizing the phonebook.....................................

Commands...................................................................

Receiving a calll...........................................................

Making a call................................................................

Using the Music function.....................................................

Selecting an audio source............................................

Commands...................................................................

The availability of some functionality only depends
on your mobile phone.
► Refer to our website www.parrot.com, in the
Compatibility section, for further information.

English

English

Installing the PARROT MKi9100

11
12
12
12
12
12
13
13
13
14
14

14
14
14

14
15

15
15
16
16

16
16
17

We advise our customers to have the Parrot
MKi9100 fitted by a professional.

A steering wheel control interface can be
used to connect your vehicle’s steering wheel
controls to your Parrot hands-free kit. With this
interface, you will be able to make phone calls via
the steering wheel controls while keeping your
hands on the wheel. Refer to our website
www.parrot.com for more information.

• Remove the audio system from your vehicles dashboard to

access the wiring harness.

• The cables supplied with the kit feature ISO connectors

and two pairs of line-out jacks. The line-out jacks can be
used if your audio system features this option (use of an
amplifier). Several set-ups are therefore possible

EN

11

depending on the type of car stereo and your vehicle.

12

• The mute function is used to cut the sound of your car

stereo to enable a phone call. The choice of the mute-in
jack depends on your car stereo’s configuration.

• Make sure the cables are not pinched at the end of
the installation process.

Installing the electronic box

Avoid installing the electronic box:

- near heating or air-conditioning system;

- on a spot directly exposed to sunlight;

- behind metal walls.

Car stereo with an ISO connector

► Refer to the installation diagram p.4.

1. Connect the male connectors of the hands-free kit to the
car stereo.

2. Join the vehicle’s audio and power supply cables to the
female connectors of the Parrot MKi9100.

3. On the installation cable, connect the free yellow wire to

one of the audio system’s corresponding mute-in jacks if
available (mute in 1, mute in 2 or mute in 3).

Car stereo with line-in

► Refer to the installation diagram p.5.

• Use this type of connection by wiring the line-out

(brown & white wire or red & black wire) to your car
stereo’s line-in.

• Using the two pairs of line-out will enable you to take

advantage of the streaming audio function in stereo
over your vehicle’s speakers.

• On the installation cable, connect the free yellow wire

to the corresponding audio system’s mute-input if available
(mute in 1, mute in 2 or mute in 3).

Car stereo without ISO connectors

To simplify the wiring procedure, you will need to purchase

an ISO adapter cable. Refer to the range of ISO adapters on

our website: www.parrot.com.

Installing the kit’s power cable

In order to check the wiring, connect the screen
before placing it on the dashboard.

► Refer to the Checking the wiring section for

more information.

• Refer to your car stereo’s wiring diagram.

13

EN

• The red wire of the kit’s cable must correspond to the

constant +12V supply, the orange wire to the ignition +12V
and the black wire to ground.

• Check that the orange wire is not connected to the

constant +12V supply, as you could run down the vehicle’s
battery, preventing your hands-free kit from operating
correctly.

On some vehicles, there is no ignition +12V on the
vehicle’s connectors. You must therefore connect
the orange power supply wire to the fuse box or
another ignition power source.

Checking the wiring

To perform the installation check, turn the ignition on then off
once the Parrot MKi9100 is installed: the message
“Good bye!” must be displayed.

If it is not the case, it is necessary to inverse the positions of
the red and orange wires. Indeed, the red wire of the power
cable must be connected to the permanent 12V, the orange
wire to the 12V ignition and the black wire to the ground.
This can be done simply by reversing both fuse holders
located on the Parrot wiring.

Installing the audio connectors

• Connect the music cable to the electronic box and
place the USB / iPod / Jack connectors into the glove

box, the central console or the parcel tray depending on
the configuration of your dashboard. Make sure that the
cable is not pinched.

• Use the provided protection cap to protect the connectors.

Installing the remote control

► Refer to the diagrams p.7/8.

• Choose the place for the remote control inside your

vehicle. We would advise you to fit it in the center of the
dashboard or close to the steering wheel.

• If you want to place the remote control on the steering

wheel, make sure it is securely attached, so that it does
not move when you are driving. Do not install the
remote control on the outside of the steering wheel and
ensure it does not get in the way when driving.

• If you want to place the remote control on the dashboard,

stick the double-sided tape located on the flat side of the
bracket to fix it against the dashboard. You can then insert
the remote onto the bracket.

14

Once you have stuck the support on the
dashboard, wait for approximately 2 hours to make
sure the adhesive tape adheres well.

Installing the double microphone

Parrots microphones are directional and need to be pointed
towards the user to pick up clear speech. The microphone
should be installed near the front roof light cluster, in the
centre of the vehicle with a clear path to the user.

Installing the screen

Remember to remove your screen when leaving the vehicle
to avoid tempting any would-be thieves and to prevent
prolonged exposure to sunlight.

Using the PARROT MKi9100 for the 1st time

Associating the control unit with the remote control

If the remote control does not seem to be associated to the
electronic box while using the Parrot MKi9100 for the first
time, press several times the red button while holding down
the green and Play buttons until the «Pairing remote control»
message is displayed. This has to be done during a 30
seconds period once the ignition is turned on.

Navigating through the menus

• Press the central jog wheel to access the menus.

> The kit says and displays the name of the current menu.

• Browse through the menus by turning the wheel and

confirm with the green button or by pressing the scroll
wheel.

• To exit the menu, press the red button or wait for a
few seconds.

Pairing and connecting a phone

to the Parrot MKi9100

Prior to using your Parrot MKi9100 with your phone for the
very first time, you must initially pair both devices.

1. Make sure the Parrot MKi9100 is set so that it is visible by
all Bluetooth ® devices. To do so, press the jog wheel and
select Settings > Bluetooth > Visibility > Visible.

The Parrot MKi9100 is visible by default.

2. Press the jog wheel and select Settings > Pair with...
> If your mobile phone’s model appears in the list, select it
and confirm.
> If your mobile phone model doesn’t appear in the list,
select the Other phones option.