ParkZone PKZ8050 User Manual

Page 1
Sukhoi SU-29MM
Instruction Manual / Bedienungsanleitung Manuel d’utilisation / Manuale di Istruzioni
Page 2
EN
NOTICE
All instructions, warranties and other collateral documents are subject to change at the sole discretion of Horizon Hobby, LLC. For up-to-date product literature, visit www.horizonhobby.com and click on the support tab for this product.
Meaning of Special Language:
NOTICE: Procedures, which if not properly followed, create a possibility of physical property damage AND little or no possibility of injury. CAUTION: Procedures, which if not properly followed, create the probability of physical property damage AND a possibility of serious injury. WARNING: Procedures, which if not properly followed, create the probability of property damage, collateral damage, and serious injury OR create a high
probability of superfi cial injury.
WARNING: Read the ENTIRE instruction manual to become familiar with the features of the product before operating. Failure to operate the product correctly can result in damage to the product, personal property and cause serious injury.
This is a sophisticated hobby product. It must be operated with caution and common sense and requires some basic mechanical ability. Failure to oper­ate this Product in a safe and responsible manner could result in injury or damage to the product or other property. This product is not intended for use by children without direct adult supervision. Do not use with incompatible components or alter this product in any way outside of the instructions provided by Horizon Hobby, LLC. This manual contains instructions for safety, operation and maintenance. It is essential to read and follow all the instructions and warn­ings in the manual, prior to assembly, setup or use, in order to operate correctly and avoid damage or serious injury.
WARNING AGAINST COUNTERFEIT PRODUCTS: If you ever need to replace your Spektrum product found in a Horizon Hobby product, always purchase from Horizon Hobby, LLC. or a Horizon Hobby authorized dealer to ensure authentic high-quality Spektrum product. Horizon Hobby, LLC. disclaims all support and warranty with regards, but not limited to, compatibility and performance of counterfeit products or products claiming compatibility with DSM or Spektrum.
Age Recommendation: Not for children under 14 years. This is not a toy.
Safety Precautions and Warnings
As the user of this product, you are solely responsible for operating in a manner that does not endanger yourself and others or result in damage to the product or the property of others.
• Always keep a safe distance in all directions around your model to avoid collisions or injury. This model is controlled by a radio signal subject to interference from many sources outside your control. Interference can cause momentary loss of control.
• Always operate your model in open spaces away from full-size vehicles, traffi c and people.
• Always carefully follow the directions and warnings for this and any optional support equipment (chargers, rechargeable battery packs, etc.).
• Always keep all chemicals, small parts and anything electrical out of the reach of children.
• Always avoid water exposure to all equipment not specifi cally designed and protected for this purpose. Moisture causes damage to electronics.
• Never place any portion of the model in your mouth as it could cause serious injury or even death.
• Never operate your model with low transmitter batteries.
• Always keep aircraft in sight and under control.
• Always use fully charged batteries.
• Always keep transmitter powered on while aircraft is powered.
• Always remove batteries before disassembly.
• Always keep moving parts clean.
• Always keep parts dry.
• Always let parts cool after use before touching.
• Always remove batteries after use.
• Always ensure failsafe is properly set before fl ying.
• Never operate aircraft with damaged wiring.
• Never touch moving parts.
2
Page 3
Table of Contents
EN
Transmitter and Receiver Binding .................................................................... 4
Battery Installation and ESC Arming ................................................................ 4
Landing Gear Installation ................................................................................ 5
Wing Installation ............................................................................................. 5
Control Horn and Servo Arm Settings .............................................................. 6
Horizontal Tail Installation ............................................................................... 6
Control Surface Centering ............................................................................... 7
Trimming ........................................................................................................ 7
Transmitter Setup ........................................................................................... 7
Dual Rates and Expos ..................................................................................... 7
SAFE
Technology Flight Modes .....................................................................8
Center of Gravity (CG) ..................................................................................... 9
Box Contents
Quick Start Reference
CG
Flight Timer
Stetting
Trimming
3.23 inches back from the leading edge
First Flight
Only trim this aircraft in AS3X® Precision Flight Mode.
82mm
of the wing at the root.
5 Min.
7 Min.
Control Direction Test ...................................................................................... 9
AS3X Control Direction Test ........................................................................... 10
Flying Tips .................................................................................................... 11
Guidlines for Flying 3D .................................................................................. 12
Motor Service ...............................................................................................13
Troubleshooting Guide SAFE ......................................................................... 13
Troubleshooting Guide .................................................................................. 14
Limited Warranty .......................................................................................... 15
Warranty and Service Contact Information .................................................... 15
Compliance Information for the European Union ............................................ 16
Replacement Parts ........................................................................................ 62
Optional Parts ............................................................................................... 63
Specifi cations
BNF Basic
10-size BL10 brushless outrunner, 1250Kv (EFLM7225)
40-Amp Switch-Mode BEC Brushless ESC (EFLA1040LB)
Spektrum AR636 6-Channel Sport Receiver
11.1V 3S 2200mAh 30C Li-Po (EFLB22003S30)
2- to 3-Cell DC Li-Po Balancing Charger (PKZ1040)
Full-Range 4-Channel (or more) 2.4GHz with
Spektrum
9
1. Read this instruction manual thoroughly.
2. Remove and inspect the contents.
3. Charge the fl ight battery.
4. Fully assemble the model.
5. Install the fl ight battery in the aircraft (once it has been fully charged).
6. Bind the aircraft to your transmitter.
7. Make sure the linkages move freely.
8. Perform the Control Direction Test with the transmitter.
9. Perform the AS3X Control Direction Test with the aircraft.
10. Adjust the fl ight controls and transmitter.
11. Perform a radio system Range Check.
12. Find a safe and open area.
13. Plan fl ight for fl ying fi eld conditions.
Prefl ight Checklist
Recommended Battery
Recommended Battery Charger
Recommended Transmitter
DSM2®/DSMX® technology. (DX6 or DX6I minimum)
Motor
4 Servos (EFLR7155)
ESC
Receiver
44.0 inches (1120mm)
42.3 inches (1074mm)
Weight:
40.6 oz (1150 g) with battery
9
1. Disconnect the fl ight battery from the ESC (Required for Safety and battery life).
2. Power OFF the transmitter.
3. Remove the fl ight battery from the aircraft.
4. Recharge the fl ight battery.
5. Repair or replace all damaged parts.
6. Store the fl ight battery apart from the aircraft and monitor the battery charge.
7. Make note of the fl ight conditions and fl ight plan results, planning for future fl ight.
Post Flight Checklist
To register your product online, visit www.parkzone.com
3
Page 4
EN
Transmitter and Receiver Binding
IMPORTANT: The included AR636 receiver has been programmed for operation
in only this aircraft.
For a list of compatible DSM2/DSMX transmitters, please visit www.bindnfl y.com.
CAUTION: When using a Futaba® transmitter with a Spektrum DSM® module, you must reverse the throttle channel and rebind. Refer to your Spektrum module manual for binding and failsafe instructions. Refer to your Futaba transmitter manual for instructions on reversing the throttle channel.
Bind Plug Installation
Failsafe
If the receiver loses transmitter communication, the failsafe will activate. When activated, the airplane controls return to the neutral position established during step 3 of the binding procedure.
Binding Procedure Reference Table
9
1. Refer to your transmitter instructions for binding to a receiver.
2. Ensure the transmitter is powered off.
3. Make sure the transmitter controls are at neutral, the throttle is in the low position and the aircraft is immobile. *
4. Install a bind plug in the receiver bind port.
5. Connect the fl ight battery in the aircraft, then power on the ESC switch. The ESC will produce a series of sounds. One long tone, then three short tones confi rm that the LVC is set for the ESC.
6. The receiver LED will begin to fl ash rapidly.
7. Power on the transmitter while holding the transmitter bind button or switch.
8. When the receiver binds to the transmitter, the light on the receiver will turn solid and the ESC will produce a series of three ascending tones. The tones indicate the ESC is armed, provided the throttle stick and throttle trim are low enough to trigger arming.
9. Remove the bind plug from the bind port.
10. Safely store the bind plug.
11. The receiver should retain the binding instructions received from the transmitter until another binding is done.
* The throttle will not arm if the transmitter’s throttle control is not put at the lowest position. If you encounter problems, follow the binding instructions and refer to the transmitter troubleshooting guide for other instructions. If needed, contact the appropriate Horizon Product Support offi ce.
Battery Installation and ESC Arming
Battery Selection
• We recommend the E-fl ite® 2200mAh 11.1V 3S 30C Li-Po (EFLB22003S30).
• If using another battery, the battery must be at least a 2200mAh 25C battery.
• Your battery should be approximately the same capacity, dimensions and weight as the E-fl ite Li-Po battery to fi t in the fuselage without changing the center of gravity a large amount.
1. Lower the throttle and throttle trim to the lowest settings. Power on the
Transmitter, then wait 5 seconds.
2. Push the button (A) into the fuselage and remove the battery hatch.
3. Install the fully charged battery (B) all the way to the front of the battery
compartment. See the Adjusting the Center of Gravity instructions for more information.
4. Make sure the fl ight battery is secured using the hook and loop strap (C).
5. Connect the battery to the ESC.
6. Power on the ESC Switch (D). Keep the aircraft immobile and away from
wind for 5 seconds or the system will not initialize.
• The ESC will sound a series of tones (refer to step 5 of the binding instructions for more information).
• An LED will light on the receiver.
A
C
B
If the ESC sounds a continuous double beep after the fl ight battery is con­nected, recharge or replace the battery.
7. After the SAFE™ system initializes, the control surfaces will move back and forth, then come to neutral to indicate the SAFE system has initialized and is ready to operate.
8. Reinstall the battery hatch. Push the rear of the battery hatch securely to ensure the latch is fully engaged.
4
D
Page 5
Landing Gear Installation
EN
1. Install the landing gear strut (A) as shown.
2. Install the U-cover (B) on the fuselage.
3. Install the fairings (C) on the strut.
4. Secure the landing gear assembly by using 4 screws (D).
Tip: Carefully support the aircraft while installing or removing screws.
Disassemble in reverse order.
B
A
D
2 X 10mm (4)
C
Wing Installation
1. Slide the wing tube (A) into the fuselage.
CAUTION: DO NOT crush or otherwise damage the wiring when
attaching the wing to the fuselage.
2. Install the left and right wing (B and C) over the wing tube and into the wing slot of the fuselage while inserting the aileron servo connectors through the provided holes.
3. Invert the fuselage so the landing gear is facing up. Secure the left and right wings to the fuselage using the included screws (D).
4. Remove the canopy (E) from the fuselage.
Tip: If needed, use hemostats or pliers to pull the servo connectors into the fuselage.
5. Connect the aileron servos from the wings to the Y-harness connectors in the fuselage. The left and right aileron servos can be connected to either side of the Y-harness.
6. Replace the canopy.
Disassemble in reverse order.
B
A
IMPORTANT: Correct operation of the AS3X system requires connection of
both ailerons to the included Y-harness and the AILE channel of the receiver.
D
3 X 22mm (2)
C
5
Page 6
EN
Control Horn and Servo Arm Settings
Fly the aircraft at these factory settings. After your fi rst fl ights, if you desire a less responsive feel, only adjust the rates for aileron, elevator and rudder using the dual rate function of your computerized transmitter.
Factory Settings
Elevator
Rudder
Ailerons
Horizontal Tail Installation
1. Slide the horizontal tail tube (A) into the hole in the rear of the fuselage.
2. Install the left and right horizontal tails (B) onto the fuselage as shown.
Ensure the control horn faces down.
3. Apply 4 pieces of tape (C) to the fuselage mounts (one on the top and
bottom of each half of the horizontal tail).
4. Attach the linkage (D) to the outermost hole in the elevator servo arm using
the link keeper (E).
5. Attach the ball link (F) to the elevator control horn using the included
nut (G) and screw (H).
6. Ensure the elevator servo arm is in the correct position, then adjust the
linkage to center the elevator.
When needed, disassemble in reverse order.
B
A
C
D
F
E
H
G
6
Page 7
EN
Control Surface Centering
IMPORTANT: Perform the Control Direction Test before performing control
surface centering.
Control Surface Centering and Adjusting a Linkage
While AS3X® technology is inactive (before advancing the throttle), mechani­cally center the control surfaces.
After binding a transmitter to the airplane’s receiver, set the trims and sub­trims to 0, ensure the servo arms are in the correct positions, then adjust the linkages to center the control surfaces.
Trimming
IMPORTANT: Only trim this aircraft in AS3X Precision Flight Mode.
After adjusting transmitter trim in the air or on the ground, do not touch the control sticks for 2 seconds. This allows the receiver to learn the correct
settings to optimize AS3X performance.
Failure to do so could affect fl ight performance.
Tip: Use needle-nose pliers or ball link pliers (RVO1005) to remove or install a link on a control horn.
• Turn the linkage clock­wise or counterclockwise until the control surface is centered.
• Attach the linkage to the servo arm or control horn after adjustment.
2 Seconds
Transmitter Setup
IMPORTANT: The included AR636 receiver has been programmed for opera-
tion in only this aircraft.
A DSM2/DSMX four-channel (or better) transmitter with dual rates is required for fl ying this aircraft. The Spektrum DX18 and JR
A DSM2/DSMX computerized transmitter with adjustable dual rates and expo is recommended for the best fl ight performance of this aircraft.
®
X9503, 11X or 12X transmitters may be used.
DX6i, DX6, DX7s, DX8, DX9, DX10t,
Transmitters DX6i and Above
Servo travel ......................................................................................100%
Always leave servo travel at 100%. Although the fl ight modes are factory set, it is strongly recomended that dual rates and expo are also used to further reduce control sensitivity for fi rst fl ights.
If you are a less experienced pilot we strongly recommend adjusting rates and expo to these settings.
Take fi rst fl ights in low rate.
Dual Rates and Expos
High Rate Expo Low Rate Expo
Aileron 100% 0% 50% 15%
Elevator 100% 0% 100% 20%
Rudder 100% 0% 40% 15%
Transmitter Setup Checklist
9
Before binding your Computerized Transmitter (DX6i, DX6, DX7/DX7se, DX7s, DX8, DX9, DX10t, DX18):
1. Choose a blank model memory with only default (zero) settings (including trim and sub-trim).
After binding:
1. Check and adjust the servos so each arm’s neutral position is perpendicular or as close to 90° as possible (loosen and adjust the servo arm splines on the servo only when needed). DO NOT use sub-trims to make fi ne adjustments, off-center sub-trim will affect servo travel and AS3X operation.
2. Adjust linkage lengths so the control surfaces center when the servo arm is close to perpendicular.
3. Set rates in the transmitter as recommended.
CAUTION: For safe operation, always re-bind the airplane after setup is complete to ensure the failsafe is updated with the latest setup.
7
Page 8
EN
SAFE™ Technology Flight Modes
The included AR636 receiver has been programmed for operation in only this aircraft, providing the following selectable fl ight modes. The programming in this receiver cannot be changed by the user.
Stagility
This mode delivers agile response, with the important addition of automatic recovery from any attitude. Release BOTH sticks and the aircraft returns to upright, fl ight. Releasing only one stick will not provide automatic recovery. Use this mode for slow fl ying and 3D maneuvers such as Harrier Rolls. Flying at
high speed in this mode will cause oscillation.
AS3X 3D Mode: Switch position 1
This mode uses high rates and high gains to deliver extreme maneuverability with maximum stability at low airspeeds. Use this mode for slow fl ying and 3D maneuvers such as Hovers and Harriers. Flying at high speed in this mode will cause oscillation.
AS3X Precision Mode: Switch position 2
This mode uses low rates and low gains to deliver precise response at high airspeeds. Use this mode to trim the aircraft and fl y fast precision maneuvers.
SAFE™ Transmitter Setup
If using any DSM2/DSMX transmitter, the radio will have to be confi gured correctly for the SAFE system to work properly.
• SAFE Flight mode is selected using Channel 5 signal (high, middle, low)
• Panic mode is selected with Channel 6 signal (high, low)
Mode: Switch position 0
Panic Recovery Mode
• If you feel you have lost control in any mode, hold the Panic Recovery button and reduce throttle. The SAFE technology will return the aircraft to upright fl ight.
• Always fl y at a safe altitude, as Panic Recovery may cause the aircraft to lose some altitude when leveling the wings.
• Release the Panic Recovery button to turn off Panic mode and return to the current SAFE fl ight mode with full stick control again.
IMPORTANT: If the aircraft is upside down when the Panic Recovery button is pressed, suffi cient altitude is re­quired for the aircraft to return to upright fl ight.
*Refer to your transmitter’s manual for more information about transmitter setup.
IMPORTANT: A transmitter with a 2-position channel 5 switch will only allow the use of position 0 or position 2 fl ight modes.
Transmitter
Throttle, Aileron, Elevator and Rudder are in Normal position. DX6i DX6 N
DX7 NN
DX7s N DX8 N DX9 N DX10t N DX18 N
N = Normal R = Reverse
DX6i
Gear/
Aux 1 Flight Mode/ Panic Switch
Ch 5
R N
1. Go to the SETUP LIST MENU
2. Set MODELTYPE: ACRO
3. Set REVERSE: Gear Channel
4. Go to ADJUST LIST MENU
5. Set TRAVEL ADJ: Gear/Fmode (0)100%; Gear/Fmode (1) 40%
6. Set FLAPS: Norm 100; LAND 100
7. Set MIX 1: ACT; Gear Gear ACT, RATE D 0%; U + 100%, SW MIX, TRIM INH Resulting in: The Gear and Mix switches operate the 3 SAFE modes
*(Flap System) Norm 100 Land 100
R *(Channel Input Confi g) Gear is B, Aux1 is switch i 3 pos Bind / i B
*(Flap System) Norm 100 Mid 100 Land 100 (3 pos Aux1 switch–0 & 1 are normal 2 is panic
R *(Switch Select) Gear to INH, FM to INH, Flap to Gear, Trainer to Aux1 3 pos Trainer Flaps R *(Switch Select) Gear to INH, FM to Gear, Flap to INH, Trainer to Aux 1 3 pos Trainer F MODE R *(Channel Input Confi g) Gear is B, Aux1 is switch i 3 pos Bind / i B R *(Channel Input Confi g) Gear is A, Aux1 is R stick 3 pos R-Stick A R *(Channel Input Confi g) Gear is B, Aux1 is switch i 3 pos Bind / i B
Gear 0; Mix 0 = Stagility™ Mode Gear 1; Mix 0 = AS3X 3D Mode Gear 1; Mix 1 = AS3X Precision Mode The Flap switch operates Panic Recovery: Position 0=Off, Position 1=On. (not a momentary switch)
DX6i 3 fl ight modes setup
SAFE Flight Modes
Supported
2 pos / 3-pos Flaps GEAR / F MODE
2 pos Flaps GEAR
Panic Recovery
Switch
SAFE Flight Mode
Switch
8
Page 9
Center of Gravity (CG)
The CG location is 82mm back from the leading edge of the wing at the root.
For fi rst fl ights, install the recommended fl ight battery all the way forward. Secure the battery with the strap as shown.
Aircraft CG and weight is based on an E-fl ite 11.1V 2200mAh 30C battery (EFLB22003S30) installed.
Control Direction Test
EN
82mm
3.23 inches back from the leading edge of the wing at the root.
Move the controls on the transmitter to make sure the aircraft control surfaces move in the proper direction.
Transmitter
Command
Up Elevator
Command
Down
Elevator
Elevator
Command
Stick Right
Aileron
Stick Left
Aircraft Reaction
Stick Right
Rudder
Stick Left
9
Page 10
EN
AS3X Control Direction Test
Perform the Control Direction Test to ensure the aircraft responds cor­rectly to your transmitter. Once you are sure the aircraft responds cor­rectly, move the aircraft as shown to ensure the AS3X system moves the control surfaces in their proper direction. If the control surfaces do not respond as shown, do not fl y the aircraft. Refer to the receiver manual for more information.
The AS3X system will not activate until the throttle stick or trim is in­creased for the fi rst time after the fl ight battery is connected and the ESC switch is in the ON position. Once the AS3X is active, the control surfaces may move rapidly on the aircraft. This is normal. AS3X will remain active until the battery is disconnected or the ESC switch is in the OFF position.
Aircraft
movement
ElevatorAileronRudder
AS3X Reaction
10
Page 11
Flying Tips
EN
Consult local laws and ordinances before choosing a fl ying location.
Range Check your Radio System
After fi nal assembly, range check the radio system with the aircraft. Refer to your specifi c transmitter instruction manual.
Oscillation
Once the AS3X system is active (after advancing the throttle for the fi rst time), you will normally see the control surfaces react to aircraft movement. In some fl ight conditions you may see oscillation (the aircraft rocks back and forth on one axis due to overcontrol). If oscillation occurs, decrease airspeed. If oscillation persists, refer to the Troubleshooting Guide for more information.
NOTICE: Fast fl ight in 3D Mode (switch position 1) and Stagility Mode (switch position 0) will cause oscillation and may damage the aircraft.
Takeoff
Place the aircraft in position for takeoff (facing into the wind). Select low rates for fi rst takeoff and gradually increase the throttle to 3/4 to full and steer with the rudder. Pull back gently on the elevator and climb to a comfortable altitude.
Wind
Fly in this area
600
feet (182.8 m)
NOTICE: If a crash is imminent, reduce the throttle and trim fully. Failure to do so could result in extra damage to the airframe, as well as damage to the ESC and motor.
NOTICE: Crash damage is not covered under warranty.
NOTICE: When you are fi nished fl ying, never leave the
aircraft in direct sunlight or in a hot, enclosed area such as a car. Doing so can damage the foam.
Always
decrease throttle at
propeller strike.
Low Voltage Cutoff (LVC)
When a Li-Po battery is discharged below 3V per cell, it will not hold a charge. The ESC protects the fl ight battery from over-discharge using Low Voltage Cutoff (LVC). Before the battery charge decreases too much, LVC removes power supplied to the motor. Power to the motor pulses, showing that some battery power is reserved for fl ight control and safe landing.
Disconnect and remove the Li-Po battery from the aircraft after use to prevent trickle discharge. Charge your Li-Po battery to about half capacity before stor­age. During storage, make sure the battery charge does not fall below 3V per cell. LVC does not prevent the battery from over-discharge during storage.
NOTICE: Repeated fl ying to LVC will damage the battery.
Tip: Monitor your aircraft battery’s voltage before and after fl ying by using a
Li-Po Cell Voltage Checker (EFLA111, sold separately).
Stand here
Flying
Fly the aircraft and trim it for level fl ight in Precision Mode (switch position 2) at 3/4 throttle. After landing, adjust the linkages mechanically to account for trim changes and then reset the trims to neutral. Ensure the aircraft will fl y straight and level with no trim or sub-trim.
Landing
For your fi rst fl ights, set your transmitter timer or a stopwatch to 5 minutes. Adjust your timer for longer or shorter fl ights once you have fl own the model. If the motor pulses, land the aircraft immediately and recharge the fl ight bat­tery. It is not recommended to fl y the battery to Low Voltage Cutoff (LVC).
To land the aircraft, fl y the aircraft down to the ground using 1/4 –1/3 throttle to allow for enough energy for a proper fl are. The aircraft is easiest to land doing a wheel landing (two point), where the aircraft touches down on the main landing gear fi rst while the tailwheel is still off the ground. The aircraft can also be landed in a three-point attitude, where all three wheels touch down at the same time. When the aircraft touches down, reduce back pressure on the elevator stick to prevent the plane from becoming airborne again.
If landing on grass, it is best to hold full up elevator after touchdown and when taxiing to prevent nosing over.
Once on the ground, avoid sharp turns until the plane has slowed enough to prevent scraping the wingtips.
Repairs
Thanks to the Z-Foam™ construction of this aircraft, repairs to the foam can be made using virtually any adhesive (hot glue, regular CA, epoxy, etc). When parts are not repairable, see the Replacement Parts List for ordering by item number. For a listing of all replacement and optional parts, refer to the list at the end of this manual.
NOTICE: Use of CA accelerant on your aircraft can damage paint. DO NOT handle the aircraft until accelerant fully dries.
11
Page 12
EN
Guidlines for Flying 3D
Getting Started
This aircraft and its SAFE™ system were designed together to help an interme­diate pilot apply standard fl ying skills to the demands of 3D fl ying. The calmer the wind conditions, the easier it is to execute maneuvers.
Select the SAFE fl ight mode that supports the maneuver you want to perform. Hold the panic recovery button to help you escape diffi culty in a maneuver. You may want to fl y low airspeed, high rate maneuvers at an altitude that allows you space to escape into forward fl ight. For your fi rst hover attempts, fl y with the canopy toward you for easier orientation.
When you fl y 3D, manage your throttle smoothly, but quickly respond to keep your model in the air and oriented the direction you want. If desired, use spotters to keep others from distracting you. Advanced 3D maneuvers always seem to attract a curious audience.
Building Your Skills
Increasing your skills takes time. Practice regularly and try following a plan for increasing your skills. Mastering one maneuver at a time may be more benefi cial than trying to learn everything all at once. Always stay aware of your aircraft’s performance in different conditions and attitudes:
What response can you consistently get from your aircraft?
• Set up your aircraft for consistent response in all attitudes and fl ight conditions where you choose to fl y. Not all challenges are due to the
equipment, just as not all challenges are due to the pilot’s skills.
• If you feel you reach a plateau in your skills, see if you have built the right habits in the fundamentals of 3D fl ying. Play to your strengths and the strengths of your aircraft while minimizing reliance on areas of weakness.
• Know yourself and your equipment well enough so you can confi dently
take on greater challenges. Push yourself, but avoid pushing past your
aircraft’s performance envelope.
• Seek fun ways to safely share your enjoyment of 3D fl ying.
Advanced 3D Maneuvers
Harrier:
Inverted Harrier:
Hover:
Torque Roll
Harrier Roll:
Waterfall:
Inverted Waterfall:
The aircraft fl ies forward slowly in a nose high (ap­proximately 45º) attitude.
The inverted aircraft fl ies forward slowly in a nose high (approximately 45º) attitude.
The aircraft nose is pointed up while the prop thrust keeps the model in the air with little or no change in altitude.
The aircraft hovers with little or no change in altitude while rotating left around its roll axis.
The aircraft does a harrier while rotating around its roll axis.
The aircraft turns over completely (360 degrees) in the pitch axis with very little forward motion or change in altitude.
The inverted aircraft turns over completely (360 degrees) in the pitch axis with very little forward motion or change in altitude.
You may want to master the Harrier fi rst, an essential maneuver used to enter and exit other 3D maneuvers.
12
Page 13
Motor Service
Disassembly
CAUTION: Always disconnect the fl ight battery from the aircraft before
removing the propeller.
1. Remove the screw (A) and spinner (B) from the collet (C).
2. Remove the spinner nut (D), propeller (E), spinner backplate (F), backplate (G) and collet from the motor shaft (H). You will need a tool to turn the spin­ner nut.
3. Remove the 3 screws (I) from the cowling (J). Carefully remove the cowling from the fuselage. Paint may keep the cowling attached to the fuselage.
4. Remove the 4 screws (K) from the motor mount (L) and the fuselage.
5. Disconnect the motor wires from the ESC wires.
6. Remove the 4 screws (M) and motor (N) from the motor mount.
EN
Assembly
Assemble in reverse order.
• Correctly align and connect the motor wire colors with the ESC wires.
• The propeller size numbers (12 x 4) must face out from the motor for correct propeller operation.
• A tool is required to tighten the spinner nut on the collet.
• Ensure the spinner is fully connected to the spinner backplate for safe operation.
Not all wiring shown.
EJ
AB
F
D
C
I
GK
Troubleshooting Guide SAFE
Problem Possible Cause Solution
Oscillation Flying too fast in Stagility or 3D
mode Flying over recommended airspeed Damaged propeller or spinner Replace propeller or spinner Imbalanced propeller Balance the propeller. For more information, view John Redman’s propeller balancing video at www.
Motor vibration Replace parts or correctly align all parts and tighten fasteners as needed Loose receiver Align and secure receiver in fuselage
Loose aircraft controls Tighten or otherwise secure parts (servo, arm, linkage, horn and control surface) Worn parts Replace worn parts (especially propeller, spinner or servo)
Irregular servo rotation Replace servo Trim change when fl ight mode is switched Incorrect response to the AS3X Control Direction Test
Receiver did not save trim
setting
Incorrect direction settings in
the receiver, which can cause
a crash
Change to Precision Mode
Reduce air speed
horizonhobby.com
After adjusting transmitter trim in the air or on the ground, do not touch the control sticks for 2 seconds
DO NOT fl y. Correct the direction settings (refer to the receiver manual), then fl y
N
L MH
13
Page 14
EN
Troubleshooting Guide
Problem Possible Cause Solution
Aircraft will not re­spond to throttle but responds to other controls
Extra propeller noise or extra vibration
Reduced fl ight time or aircraft underpow­ered
Aircraft will not Bind (during binding) to transmitter
Aircraft will not con­nect (after binding) to transmitter
Control surface does not move
Aircraft control surfaces do not move after switch is turned on
Controls reversed Transmitter settings are reversed Perform the Control Direction Test and adjust the controls on
Motor power pulses then motor loses power
Throttle not at lowest position or throttle trim too high Reset controls with throttle stick and throttle trim at lowest setting Throttle servo travel is lower than 100% Make sure throttle servo travel is 100% or greater Throttle channel is reversed Reverse throttle channel on transmitter
Motor disconnected from ESC Make sure motor is connected to the ESC Damaged propeller and spinner, collet or motor Replace damaged parts
Propeller is out of balance Balance or replace propeller Prop nut is too loose Tighten the prop nut Spinner is not tight or fully seated in place Tighten the spinner or remove the spinner and turn it 180 degrees Flight battery charge is low Completely recharge fl ight battery Propeller installed backwards Install propeller with numbers facing forward
Flight battery damaged Replace fl ight battery and follow fl ight battery instructions Flight conditions may be too cold Make sure battery is warm before use Battery C rating is too low Replace battery or use battery with correct C rating Transmitter too near aircraft during binding process Move powered transmitter a few feet from aircraft, disconnect and recon-
Aircraft or transmitter is too close to large metal object, wireless source or another transmitter
The bind plug is not installed correctly in the bind port Install bind plug in bind port and bind the aircraft to the transmitter Flight battery/Transmitter battery charge is too low Replace/recharge batteries
Bind switch or button not held long enough during bind process
ESC is powered off Power on the ESC switch
Transmitter too near aircraft during connecting process Move powered transmitter a few feet from aircraft, disconnect and
Aircraft or transmitter is too close to large metal object, wireless source or another transmitter
Bind plug left installed in bind port Rebind transmitter to the aircraft and remove the bind plug before
Aircraft bound to different model memory (ModelMatch radios only)
Flight battery/Transmitter battery charge is too low Replace/recharge batteries Transmitter may have been bound using different DSM
protocol
ESC is powered off Power on the ESC switch Control surface, control horn, linkage or servo damage Replace or repair damaged parts and adjust controls Wire damaged or connections loose Do a check of wires and connections, connect or replace as needed
Transmitter is not bound correctly or the incorrect model was selected
Flight battery charge is low Fully recharge fl ight battery BEC (Battery Elimination Circuit) of the ESC is damaged Replace ESC
ESC is powered off Power on the ESC switch
Aircraft was moving during initialization Keep aircraft still during initialization
ESC uses default soft Low Voltage Cutoff (LVC) Recharge fl ight battery or replace battery that is no longer performing Weather conditions might be too cold Postpone flight until weather is warmer
Battery is old, worn out, or damaged Replace battery Battery C rating might be too small Use recommended battery
nect fl ight battery to aircraft Move aircraft and transmitter to another location and attempt
binding again
Power off transmitter and repeat bind process. Hold transmitter bind button or switch until receiver is bound
reconnect fl ight battery to aircraft Move aircraft and transmitter to another location and attempt
connecting again
cycling power
TM
Select correct model memory on transmitter
Bind aircraft to transmitter
Re-bind or select correct model in transmitter
transmitter appropriately
14
Page 15
Limited Warranty
EN
What this Warranty Covers
Horizon Hobby, LLC. (“Horizon”) warrants to the original purchaser that the product purchased (the “Product”) will be free from defects in materials and workmanship at the date of purchase.
What is Not Covered
This warranty is not transferable and does not cover (i) cosmetic damage, (ii) damage due to acts of God, accident, misuse, abuse, negligence, commercial use, or due to improper use, installation, operation or maintenance, (iii) modi­fication of or to any part of the Product, (iv) attempted service by anyone other than a Horizon Hobby authorized service center, (v) Product not purchased from an authorized Horizon dealer, or (vi) Product not compliant with appli­cable technical regulations.
OTHER THAN THE EXPRESS WARRANTY ABOVE, HORIZON MAKES NO OTHER WARRANTY OR REPRESENTATION, AND HEREBY DISCLAIMS ANY AND ALL IMPLIED WARRANTIES, INCLUDING, WITHOUT LIMITATION, THE IMPLIED WARRANTIES OF NON-INFRINGEMENT, MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE PURCHASER ACKNOWLEDGES THAT THEY ALONE HAVE DETERMINED THAT THE PRODUCT WILL SUITABLY MEET THE REQUIREMENTS OF THE PURCHASER’S INTENDED USE.
Purchaser’s Remedy
Horizon’s sole obligation and purchaser’s sole and exclusive remedy shall be that Horizon will, at its option, either (i) service, or (ii) replace, any Product determined by Horizon to be defective. Horizon reserves the right to inspect any and all Product(s) involved in a warranty claim. Service or replacement decisions are at the sole discretion of Horizon. Proof of purchase is required for all warranty claims. SERVICE OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE PURCHASER’S SOLE AND EXCLUSIVE REMEDY.
Limitation of Liability
HORIZON SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES, LOSS OF PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN ANY WAY, REGARDLESS OF WHETHER SUCH CLAIM IS BASED IN CONTRACT, WARRANTY, TORT, NEGLIGENCE, STRICT LIABILITY OR ANY OTHER THEORY OF LIABILITY, EVEN IF HORIZON HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Further, in no event shall the liability of Horizon exceed the individual price of the Product on which liability is assert­ed. As Horizon has no control over use, setup, final assembly, modification or misuse, no liability shall be assumed nor accepted for any resulting damage or injury. By the act of use, setup or assembly, the user accepts all resulting liability. If you as the purchaser or user are not prepared to accept the liability associated with the use of the Product, purchaser is advised to return the Product immediately in new and unused condition to the place of purchase.
Law
These terms are governed by Illinois law (without regard to conflict of law principals). This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. Horizon reserves the right to change or modify this warranty at any time without notice.
WARRANTY SERVICES Questions, Assistance, and Services
Your local hobby store and/or place of purchase cannot provide warranty sup­port or service. Once assembly, setup or use of the Product has been started, you must contact your local distributor or Horizon directly. This will enable Horizon to better answer your questions and service you in the event that
you may need any assistance. For questions or assistance, please visit our website at www.horizonhobby.com, submit a Product Support Inquiry, or call the toll free telephone number referenced in the Warranty and Service Contact Information section to speak with a Product Support representative.
Inspection or Services
If this Product needs to be inspected or serviced and is compliant in the country you live and use the Product in, please use the Horizon Online Service Request submission process found on our website or call Horizon to obtain a Return Merchandise Authorization (RMA) number. Pack the Product securely using a shipping carton. Please note that original boxes may be included, but are not designed to withstand the rigors of shipping without additional protection. Ship via a carrier that provides tracking and insurance for lost or damaged parcels, as Horizon is not responsible for merchandise until it arrives and is accepted at our facility. An Online Service Request is available at http:// www.horizonhobby.com/content/_service-center_render-service-center. If you do not have internet access, please contact Horizon Product Support to obtain a RMA number along with instructions for submitting your product for service. When calling Horizon, you will be asked to provide your complete name, street address, email address and phone number where you can be reached during business hours. When sending product into Horizon, please include your RMA number, a list of the included items, and a brief summary of the problem. A copy of your original sales receipt must be included for warranty consider­ation. Be sure your name, address, and RMA number are clearly written on the outside of the shipping carton.
NOTICE: Do not ship LiPo batteries to Horizon. If you have any issue with a LiPo battery, please contact the appropriate Horizon Product Support office.
Warranty Requirements For Warranty consideration, you must include your original sales receipt verifying the proof-of-purchase date. Provided warranty conditions have
been met, your Product will be serviced or replaced free of charge. Service or replacement decisions are at the sole discretion of Horizon.
Non-Warranty Service Should your service not be covered by warranty, service will be com­pleted and payment will be required without notification or estimate of the expense unless the expense exceeds 50% of the retail purchase cost. By submitting the item for service you are agreeing to payment of the
service without notification. Service estimates are available upon request. You must include this request with your item submitted for service. Non-warranty service estimates will be billed a minimum of ½ hour of labor. In addition you will be billed for return freight. Horizon accepts money orders and cashier’s checks, as well as Visa, MasterCard, American Express, and Discover cards. By submitting any item to Horizon for service, you are agreeing to Horizon’s Terms and Conditions found on our website http://www.horizonhobby.com/ content/_service-center_render-service-center.
ATTENTION: Horizon service is limited to Product compliant in the coun­try of use and ownership. If received, a non-compliant Product will not be serviced. Further, the sender will be responsible for arranging return shipment of the un-serviced Product, through a carrier of the sender’s choice and at the sender’s expense. Horizon will hold non-compliant Product for a period of 60 days from notification, after which it will be discarded.
Warranty and Service Contact Information
Country of Purchase Horizon Hobby Phone Number/Email Address Address
United States of
America
United Kingdom
Germany
France
China
Horizon Service Center
(Repairs and Repair Requests)
Horizon Product Support
(Product Technical Assistance)
Sales
Service/Parts/Sales:
Horizon Hobby Limited
Horizon Technischer Service service@horizonhobby.de Sales: Horizon Hobby GmbH +49 (0) 4121 2655 100
Service/Parts/Sales:
Horizon Hobby SAS
Service/Parts/Sales:
Horizon Hobby – China
servicecenter.horizonhobby.com/RequestForm/
www.quickbase.com/db bghj7ey8c?a=GenNewRecord
888-959-2305
sales@horizonhobby.com
888-959-2305
sales@horizonhobby.co.uk
+44 (0) 1279 641 097
infofrance@horizonhobby.com
+33 (0) 1 60 18 34 90
info@horizonhobby.com.cn
+86 (021) 5180 9868
4105 Fieldstone Rd
Champaign, Illinois, 61822 USA
Units 1–4 , Ployters Rd, Staple Tye
Harlow, Essex, CM18 7NS, United Kingdom
Christian-Junge-Straße 1
25337 Elmshorn, Germany
11 Rue Georges Charpak
77127 Lieusaint, France
Room 506, No. 97 Changshou Rd.
Shanghai, China 200060
15
Page 16
EN
FCC Infromation
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
IC Infromation
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
Compliance Information for the European Union
Declaration of Conformity
(in accordance with ISO/IEC 17050-1)
No. HH2014051801
Product(s): Sukhoi SU-29MM BNF Basic Item Number(s): PKZ8050 Equipment class: 1
The object of declaration described above is in conformity with the require­ments of the specifi cations listed below, following the provisions of the Euro­pean R&TTE Directive 1999/5/EC and EMC Directive 2004/108/EC:
EN301 489-1 V1.9.2: 2012 EN301 489-17 V2.1.1: 2009
Instructions for disposal of WEEE by users in the European Union
This product must not be disposed of with other waste. Instead, it is the user’s responsibility to dispose of their waste equipment by handing it over to a designated collections point for the recycling of waste electrical and electronic equipment. The separate collection
and recycling of your waste equipment at the time of disposal will help to conserve natural resources and ensure that it is recycled in a manner that protects human health and the environment. For more information about where you can drop off your waste equipment for recycling, please contact your local city offi ce, your household waste disposal service or where you purchased the product.
EN55022:2010 + AC:2011 EN55024:2010
Signed for and on behalf of: Horizon Hobby, LLC Champaign, IL USA May 18, 2014
Chief Financial Offi cer
Robert Peak
Horizon Hobby, LLC
16
Page 17
Replacement Parts • Ersatzteile • Pièces de rechange • Pezzi di ricambio
Part # | Nummer Numéro | Codice
PKZ8002 PKZ8008 PKZ8006 PKZ8021 PKZ8005 PKZ8025 PKZ8022
PKZ8067
PKZ8020
PKZ8026
PKZ8013
PKZ6528
EFLM7225
EFLM72252
EFLA1040LB
SPMAR636SU
EFLP12040E EFLR7155
EFLM72251
Description Beschreibung Description Descrizione
Decal Set: SU-29MM Dekorbogen: SU-29MM Planche de décalcomanies : SU-29MM Foglio con decalcomanie: SU-29MM Spinner: SU-29MM Spinner: SU-29MM Cône: SU-29MM Ogiva: SU-29MM Main gear set: SU-29MM Fahrwerksset: SU-29MM Jambes de train principal : SU-29MM Set ingranaggio principale: SU-29MM Wing Tube: SU-29MM Hatch and Canopy SU-29MM Horizontal Stab: SU-29MM
Pushrod set: SU-29MM
Bare Fuse: SU-29MM
Wing Set: SU-29MM
Rudderw/tail wheel: SU-29MM
Cowl: SU-29MM
Motor mount: VisionAire Motorbefestigung: VisionAire Support moteur : VisionAire Supporto del motore: VisionAire
BL10 Motor: VisionAire
Prop Adapter: VisionAire
40-Amp Lite Pro Switch-Mode BEC Brushless ESC (V2)
AR636 Sukhoi SU-29MM Replace­ment Receiver
Propeller: 12 x 4E Propeller: 12 x 4E Hélice 12x4E Elica: 12x4E
13 g Digital Micro Servo E-fl ite 13g Digital Micro Servo Micro servo digital 13g Micro servo digitale 13g
BL10 Motor Shaft: VisionAire
Flächenverbinder: SU-29MM Clé d’aile : SU-29MM Kabinenhaube u. Klappe: SU-29MM Verrière avec trappe : SU-29MM Höhenruder: SU-29MM Stabilisateur : SU-29MM Gestängeset: SU-29MM Set de tringleries : SU-29MM
Parkzone SU-29MM Rumpf o. Einbauten: SU-29MM
Parkzone SU-29MM Tragfl ächenset: SU-29MM
Fuselage nu : SU-29MM Solo fusoliera: SU-29MM
Aile : SU-29MM Set ala: SU-29MM
Leitwerk m. Spornrad: SU-29MM Roues et roulette : SU-29MM
Parkzone SU-29MM Motorhaube: SU­29MM
Parkzone VisionAire BL10 Motor: VisionAire Parkzone VisionAire Propeller Adapter: VisionAire
E-fl ite 40-Amp Lite Pro Switch-Mode BEC Brushless Regler (V2)
Sukhoi SU-29MM: Ersatzempfänger Récepteur de rechange : Sukhoi
Parkzone VisionAire BL10 Motorwelle: VisionAire
Capot : SU-29MM Capottina motore: SU-29MM
Moteur BL10 : VisionAire Motore BL10: VisionAire
Adaptateur d’hélice : VisionAire Adattatore elica: VisionAire
Contrôleur Brushless 40A Lite Pro Switch mode BEC V2
SU-29MM
Axe de moteur BL10 Albero motore BL10: VisionAire
Tubo ala: SU-29MM Portello e capottina: SU-29MM Stabilizzatore orizzontale: SU-29MM
Set rinvii di comando: SU-29MM
Timone con ruotino di coda: SU-29MM
Regolatore 40-Amp Pro Switch-Mode BEC Brushless ESC (V2)
Ricevitore di ricambio: Sukhoi SU­29MM
62
Page 18
Optional Parts • Optionale Bauteile • Pièces optionnelles • Pezzi opzionali
Part # | Nummer Numéro | Codice
EFLA250
EFLAEC302 EC3 Battery Connector (2) E-fl ite EC3 Akkukabel, Buchse (2) Prises EC3 coté batterie (2) Connettore batteria
EFLAEC303 EC3 Device/Battery Connector
RVO1005 Ball Link Pliers Revolution Deluxe Kugelkopfzange Pince à rotules Pinze per attacchi a sfera EFLB22003S30 11.1V 3S 30C 2200MAH Li-Po 11.1V 3S 30C 2200mAh LiPo 11.1V 3S 30C 2200MAH Li-Po 11.1V 3S 30C 2200MAH Li-Po PKZ1029 11.1V 3S 25C 2200MAH Li-Po 11.1V 3S 25C 2200mAh LiPo 11.1V 3S 25C 2200MAH Li-Po 11.1V 3S 25C 2200MAH Li-Po EFLA111 Li-Po Cell Voltage Checker E-fl ite Li-Po Cell Volt Checker Contrôleur de tension Li-Po Controllo tensione batteria LiPo
PKZ1040 2-3 DC Lipo balancing charger 2-3 DC Lipo-Balancer-Ladegerät
DYNC2010
DYN1405
DYN1400
Description Beschreibung Description Descrizione
Park Flyer Tool Assortment, 5 pc
Prophet Sport Plus 50W AC DC Charger
Li-Po Charge Protection Bag, Large
Li-Po Charge Protection Bag, Small
DX6i DSMX 6-Channel Trans­mitter
DX6 DSMX 6-Channel Trans­mitter
DX7s DSMX 7-Channel Trans­mitter
DX8 DSMX 8-Channel Trans­mitter
DX9 DSMX 9-Channel Trans­mitter
DX18 DSMX 18-Channel Transmitter
E-fl ite Park Flyer Werkzeugsorti­ment; 5 teilig
E-fl ite EC3 Kabelsatz, Stecker/ Buchse
Dynamite Ladegerät Prophet Sport Plus 50W AC/DC EU
Dynamite LiPoCharge Protection Bag groß
Dynamite LiPoCharge Protection Bag klein
Spektrum DX6i DSMX 6-Kanal Sender
Spektrum DX6 DSMX 6-Kanal Sender
Spektrum DX7s DSMX 7 Kanal Sender
Spektrum DX8 DSMX 8 Kanal Sender
Spektrum DX9 DSMX 9 Kanal Sender
Spektrum DX18 DSMX 18 Kanal Sender
Assortiment d'outils park fl yer, 5pc
Prises EC3 coté contrôleur (2) Connettore batteria/dispositivo
Chargeur-équilibreur CC Li-Po 2–3 cellules
Chargeur Prophet Sport Plus 50W AC DC
Sac de charge Li-Po, grand modèle Busta protezione grande par LiPo
Sac de charge Li-Po, petit modèle Busta protezione piccola par LiPo
Emetteur DX6i DSMX 6 voies DX6i DSMX Trasmettitore 6 canali
Emetteur DX6 DSMX 6 voies DX6 DSMX Trasmettitore 6 canali
Emetteur DX7s DSMX 7 voies
Emetteur DX8 DSMX 8 voies DX8 DSMX Trasmettitore 8
Emetteur DX9 DSMX 9 voies DX9 DSMX Trasmettitore 9
Emetteur DX18 DSMX 18 voies DX18 DSMX Trasmettitore 18
Park Flyer assortimento attrezzi, 5 pc
Caricabatteria con bilanciatore per 2 o 3 celle Li-Po
Prophet Sport Plus 50W AC DC Caricabatterie
DX7s DSMX Trasmettitore 7 canali
canali
canali
canali
63
Page 19
© 2014 Horizon Hobby, LLC.
ParkZone, E-flite, Prophet, SAFE, the SAFE logo, AS3X, EC3, DSM, DSM2, DSMX, Z-Foam, the BNF logo, and ModelMatch are trademarks or registered trademarks of Horizon Hobby, LLC. The Spektrum trademark is used with permission of Bachmann Industries, Inc. JR is a registered trademark of JR Americas. Futaba is a registered trademark of Futaba Denshi Kogyo Kabushiki Kaisha Corporation of Japan. All other trademarks, service marks and logos are property of their respective owners.
www.parkzone.com PKZ8050
Created 08/14 42459.2
Loading...