Parkside PWS 1200, KH 3116 ANGLE GRINDER Operation And Safety Notes
Kompernaß GmbH
Burgstraße 21
D-44867 Bochum (Germany)
Last Information Update:
08 / 2007 · Ident.-No.: PWS1200082007-6
ANGLEGRINDER
PWS 1200
GB / IE / CY Operation and Safety Notes Page 5
ANGLE GRINDER
Operation and Safety Notes
Before reading, unfold the page containing the illustrations and familiarise yourself with all functions
of the device.
A B
D E
10 1 2
3
4
5
6
7
8
9
C
F
11
12
7
5 GB/IE/CY 5 GB/IE/CY
Introduction
Proper use .....................................................................................................................Page 6
Features and equipment ...............................................................................................Page 7
Included items ...............................................................................................................Page 7
Technical information ...................................................................................................Page 7
Safety advice
Workplace safety .........................................................................................................Page 8
Electrical safety .............................................................................................................Page 8
Personal safety ..............................................................................................................Page 8
Careful handling and use of electrical power tools ..................................................Page 9
Safety advice relating specifically to this device .......................................................Page 9
Advice on use ...............................................................................................................Page 10
Use
Operation ......................................................................................................................Page 11
Switching on and off ....................................................................................................Page 12
Setting the speed ..........................................................................................................Page 12
Changing a disc............................................................................................................Page 12
Use of accessories
Cutting / roughing discs ...............................................................................................Page 13
Flap discs for metal .......................................................................................................Page 13
Other accessories .........................................................................................................Page 13
Adjusting the disc guard cover ....................................................................................Page 14
Using the auxiliary handle ...........................................................................................Page 14
Maintenance and cleaning ........................................................................Page 14
Disposal ......................................................................................................................Page 14
Information
Service centre ...............................................................................................................Page 15
Declaration of Conformity / Manufacturer
.................................................................Page 15
Table of Content
6 GB/IE/CY
Angle grinder PWS 1200
Grinding, roughing, cutting
and polishing
Introduction
Please make sure you familiarise your-
self fully with the way the device works
before you use it for the first time and
that you understand how to handle electrical power tools correctly. To help you do this please read
the accompanying operating instructions. Keep
these instructions in a safe place. If you pass the
device on to anyone else, please ensure that you
also pass on all the documentation.
Proper use
The device is intended for the dry cutting, rough
grinding and brushing of metal and stone. With approved types of abrasive consumables and tools
the device can also be used for finish grinding and
polishing. Any other use or modification to the device shall be considered as improper use and
could give rise to considerable dangers. We will
not accept liability for loss or damage arising from
improper use. The device is not intended for commercial use.
Note: Slots cut in load-bearing walls must comply
with standard DIN 1053 Part 1 or the regulations
applicable in your country.
These instructions and advice must be observed.
Before you start a task, seek the advice of a competent structural engineer, architect, or the relevant
site management staff.
The following pictogrammes / symbols are used in these operating instructions:
Read the operating instructions!
n
0
Rated idle running speed
Always heed warning labels and
safety instructions!
Protection category II power tool;
double insulated
Caution - Danger of electric shock! Hazardous
voltage – danger to life!
Proper procedure and handling.
Explosive material!
Wear hearing protection, dust protection mask,
protective glasses and protective gloves.
Risk of fire!
Keep children and other unauthorised personnel
at a safe distance when using electrical tools.
Soft start to limit heavy transient current surges
Keep the device away from rain or moisture. Water entering an electrical device increases the risk
of electric shock.
V
~
Volt (AC)
Damaged appliances, power cables and power
plugs mean potentially fatal risks from electric
shock. Regularly check the condition of the appliance, the power cables and the power plugs.
W
Watts (effective power)
Dispose packaging and appliance in an
environmentally-friendly way!
Introduction
7 GB/IE/CY
Features and equipment
1
Locking knob
2
Handle with softzone grip
3
ON/OFF switch
4
Carbon brushes access cover
5
Auxiliary handle
6
Adjustable disc guard cover
7
Clamping nut
8
Mounting spindle
9
Mounting flange
10
Spindle lock button
11
Rotation speed preselector wheel (Fig. A)
12
Spanner (Fig. C)
Included items
1 Metal-cutting disc, 125 x 2.5 x 22 mm
1 Auxiliary handle
1 Disc guard cover
1 Spanner
2 Replacement carbon brushes (not illustrated)
1 Operating instructions
1 Booklet covering “Warranty and service”
Technical information
Rated output: 1200 W
Rated voltage: 230 V ~ 50 Hz
Design no-load speed: n
0
3,000 - 11,000 min
-1
Spindle thread: M14
Protection class: II /
&
Noise and vibration data:
Refers to A-weighted sound level.
Sound pressure level: 92.5 dB (A)
Sound power level: 105.5 dB (A)
Weighted acceleration, typical.
Hand-arm vibration: < 2.5 m/s
2
Wear hearing protection!
INTELLIGENT POWER CONTROL
The PWS 1200 angle grinder has
INTELLIGENT POWER CONTROL.
This electronic management system monitors and
controls the various operating states of your device.
Switching on:
The IPC electronic system start-up stage ensures
that the motor starts up slowly and gently.
This largely avoids heavy transient current surges.
No-load running:
After switching on, the IPC electronic system takes
the grinder’s speed up to the preselected value
(Setting 1 … 6). After this is reached, the IPC system speed control stage keeps the grinder operating at a constant speed.
Overload operation:
The IPC electronic system ensures that the current is
limited if the device becomes overloaded.
Safety advice
J Attention! In order to protect yourself from the
danger of electric shock, injury or fire when using electrical power tools, please observe the
following safety precautions. Read and take
note of these instructions and advice before
you use the device. Failure to observe the instructions and advice given below may result in
electric shock, fire and/or serious injury.
Introduction / Safety advice
PWS 1200 KH3116
Date of manufacture: 02-2008
230 V~50 Hz · 1200 W
n
0
3000 - 11000 min
-1
Kompernaß GmbH · D- 44867 Bochum · Germany
www.kompernass.com
intelligent
power control
Loading...