Page 1
Bulletin HY30-5501-M1/UK
Service Manual
Series F1/T1
Effective: June, 2018
Supersedes: December, 2016
Page 2
HY30-5501-M1/UK
Service Manual
Series F1/T1
List of contents Page
New attributes on F1/T1............................................................................3
...........................................................4
Check of shaft seal....................................................................................5
..............................................................6
Direction of rotation ...................................................................................8
...........................................................................................9
..............................................................................................10
Split view / spare parts ............................................................................ 11
Split view / spare parts (motor)................................................................12
Spare part kits and tools..........................................................................13
Conversion factors
3 3
1 cm
!
WARNING
FAILURE OR IMPROPER SELECTION OR IMPROPER USE OF THE PRODUCTS AND/OR SYSTEMS DESCRIBED
HEREIN OR RELATED ITEMS CAN CAUSE DEATH, PERSONAL INJURY AND PROPERTY DAMAGE.
-
Please contact your Parker representation for a detailed ”Offer of Sale”.
Offer of Sale
2
Pump and Motor Division
Trollhättan, Sweden
Page 3
Bulletin HY30-5501-M1/UK
F1/T1
The F1/T1 series offers many additional
container lifts, skip loaders, forest cranes,
tions.
-
Service Manual
Series F1/T1
-
New features of the F1/T1 are:
ments
... thanks to:
F1-25/-41/-51/-61.
-
F1-81/-101.
All of this in addition to previous
features:
temperture shocks
ISO standard
3
Pump and Motor Division
Trollhättan, Sweden
Page 4
HY30-5501-M1/UK
Displacement [cm
Max operating pressure [bar]
Shaft speed [rpm]
Service Manual
Series F1/T1
F1 frame size 25 41 51 61 81 101
3
/rev] 25,6 40,9 51,1 59,5 81,6 102,9
1)
[l/min]
continuous 350 350
intermittent 400 400
2)
185
2)
at 400 bar
Torque [Nm]
Input power [kW]
Weight
Pump cross section
1)
2600 2400 2200 2200 20002)1800
1) 2)
on mineral oil at a viscosity of 30 mm2/s (cSt).
2) Valid with 2
1
/2” inlet (suction) line.
6
2)
Design and function
F1 is a piston pump with sherical pistons (1)
o
to the shaft (3). When the shaft
rotates, the pistons move up and down in the cylin-
connects the cylinder barrel to the drive shaft, cau-
4
2
4
1
eliminates a separate drain line to the tank. F1 is
direct to PTO´s with ZF standard.
4
Pump and Motor Division
Trollhättan, Sweden
5
Page 5
Bulletin HY30-5501-M1/UK
Service Manual
Series F1/T1
Check of Shaft Seal and seal towards PTO
Indication hole is placed under the protection cover.
-
Note:
-
5
Pump and Motor Division
Trollhättan, Sweden
Page 6
HY30-5501-M1/UK
ter and a relief valve.
Service Manual
Series F1/T1
-
Test instrument with
valve
F01-025 1000 21,6
F01-041 1000 34,2
F01-051 1000 44,1
F01-061 1000 54,9
F01-081 1000
F01-101 1000 88,2
Rpm
6
Pump and Motor Division
Trollhättan, Sweden
Page 7
Bulletin HY30-5501-M1/UK
Service Manual
Series F1/T1
Checking the performance of F1 motor
drain line and keep the drain port above a suitable container. Run the unit at normal speed
-
Pres-
sure
(l/min)
(bar)
F01-025-M 150 2.0
F01-041-M 150 2.5
F01-051-M 150 2.5
F01-061-M 150 2.5
F01-081-M 150 3.0
F01-101-M 150 3.0
F01-121-M 150 3.0
Pump and Motor Division
Trollhättan, Sweden
Page 8
HY30-5501-M1/UK
Direction of rotation
Service Manual
Series F1/T1
Disassembling
1.
shaft upwards.
The factory assembled direction of rotation,
appears on the label and by arrows on the
vs. shaft rotation. The direction of rotation
Remove the four cap screws and turn the
Nm.
2.
protective washer (item 236).
Center screw
Plastic seal
3.
Start-up
Make sure the entire hydraulic system is
5 Nm.
-
couple of turns. Take the mandrel which co-
sible to turn the mandrel 90°, down in the
8
Pump and Motor Division
Trollhättan, Sweden
-
-
Page 9
Bulletin HY30-5501-M1/UK
Only on the prototypes!
4.
Disassemble the end cap.
Service Manual
Series F1/T1
5.
Take out the shaft, the pistons, the barrel
support and the cylinder barrel from the
6.
-
barrel support is kept in position in the barrel with a snap function.
9
Pump and Motor Division
Trollhättan, Sweden
Page 10
HY30-5501-M1/UK
Service Manual
Series F1/T1
Assembling
1.
Fasten the end cap in a vice with the center
shaft upwards.
3.
Pressed in two steps.
4.
2.
Place the pistons and the barrel support in
the cylinder barrel. Place the shaft over the
pistons and on the barrel support. Turn the
-
ble the cylinder barrel on the end cap. En-
in two steps. First step with the assemble
tool alone. Second step with assemble tool
outher diameter of the casette seal with hy-
Fasten the assembly screw a couple of
possible. Reassemble the protective wash-
Turn the shaft
at least on rev.
to ensure correct
10
Pump and Motor Division
Trollhättan, Sweden
Page 11
Bulletin HY30-5501-M1/UK
491
Service Manual
Series F1/T1
Splitview / Spare Parts
980
982
111
310
452
223
411
460
End cap Item 111
End cap BSP Item 111
Barrel support Item 430
Piston Item 440
440
430
211
130
Cylinder barrel Item 411
Bearing housing Item 211
Shaft Item 310
Ring gear Item 452
Tap Rol bearing Item 460
11
233
236
238
465
Pump and Motor Division
Trollhättan, Sweden
Page 12
HY30-5501-M1/UK
491
Service Manual
Series F1/T1
Splitview / Spare Parts F1 Motor
111
310
223
411
452
460
440
End cap Item 111
Barrel support Item 430
Piston Item 440
Bearing housing Item 211
Cylinder barrel Item 411
430
211
Shaft Item 310
233
Ring gear Item 452
234
Tap Rol bearing Item 460
12
Pump and Motor Division
Trollhättan, Sweden
Page 13
Bulletin HY30-5501-M1/UK
Spare Part Kits and Tools
Seal kit
Unit Part no.
Items included:
130, 223, 233, (234 motor), 236,
Spare part kit (F1 Pump)
Unit Part no.
Service Manual
Series F1/T1
Item Description
111 End Cap
228 Gasket
233 Shaft Seal
236 Protective Washer
241 Gasket
310 Shaft
411 Cylinder Barrel
430 Barrel Support
440 Piston
Items included:
111, 130, 223, 233, 236, 238, 411,
Spare Part Kit (T1 pump)
Unit Part no.
Items included:
111, 130, 223, 233, 236, 238, 411,
Assembly kit
Unit Part no.
Item included:
236, 238, 465
Exchange Units
Unit Part no.
Note! Not on all markets.
Dis- and re-assembling tool
Detail Part no.
13
Pump and Motor Division
Trollhättan, Sweden
Page 14
Pump and Motor Division
SE-461 82 Trollhättan
Sweden
www.parker.com
Loading...