Paradyne JetFusion Integrated Access Device User Manual
JetFusion
Integrated Access Device
User’s Guide
Document No. 2000-A2-GB20-10
February 2004
Copyright © 2004 Paradyne Corporation.
All rights reserved.
Printed in U.S.A.
Notice
This publication is protected by federal copyright law. No part of this publication may be copied or distributed,
transmitted, transcribed, stored in a retrieval system, or translated into any human or computer language in any form or
by any means, electronic, mechanical, magnetic, manual or otherwise, or disclosed to third parties without the express
written permission of Paradyne Corporation, 8545 126th Ave. N., Largo, FL 33773.
Paradyne Corporation makes no representation or warranties with respect to the contents hereof and specifically
disclaims any implied warranties of merchantability or fitness for a particular purpose. Further, Paradyne Corporation
reserves the right to revise this publication and to make changes from time to time in the contents hereof without
obligation of Paradyne Corporation to notify any person of such revision or changes.
Changes and enhancements to the product and to the information herein will be documented and issued as a new
release to this manual.
Warranty, Sales, Service, and Training Information
Contact your local sales representative, service representative, or distributor directly for any help needed. For
additional information concerning warranty, sales, service, repair, installation, documentation, training, distributor
locations, or Paradyne worldwide office locations, use one of the following methods:
Internet: Visit the Paradyne World Wide Web site at www.paradyne.com. (Be sure to register your warranty at
www.paradyne.com/warranty.)
Telephone: Call our automated system to receive current information by fax or to speak with a company
representative.
— Within the U.S.A., call 1-800-870-2221
— Outside the U.S.A., call 1-727-530-2340
Document Feedback
We welcome your comments and suggestions about this document. Please mail them to Technical Publications,
Paradyne Corporation, 8545 126th Ave. N., Largo, FL 33773, or send e-mail to userdoc@paradyne.com. Include the
number and title of this document in your correspondence. Please include your name and phone number if you are
willing to provide additional clarification.
Trade mar ks
ACCULINK, COMSPHERE, ETC, EtherLoop, FrameSaver, GranDSLAM, Hotwire, the Hotwire logo, Jetstream, MVL,
NextEDGE, OpenLane, Paradyne, the Paradyne logo, Paradyne Credit Corp., the Paradyne Credit Corp. logo,
Performance Wizard, StormPort, and TruePut are all registered trademarks of Paradyne Corporation. ADSL/R,
BitStorm, Connect to Success, GrandVIEW, Hotwire Connected, iMarc, JetFusion, JetVision, MicroBurst,
PacketSurfer, ReachDSL, Spectrum Manager, StormTracker, and TriplePlay are trademarks of Paradyne Corporation.
All other products and services mentioned herein are the trademarks, service marks, registered trademarks, or
registered service marks of their respective owners.
2000-A2-GB20-10 - A - February 2004
7DEOHRI&RQWHQWV
Preface
Audience.................................................................................. xi
Contents .................................................................................. xi
Safeguards ..............................................................................xii
Product Warranty....................................................................xiii
Conventions............................................................................xiii
Regulatory Notices .................................................................xiii
Chapter 1 Introduction
Data Interfaces .........................................................................2
JetFusion 2/4/8-Port IAD Family...............................................2
Front Panel Power and Status Indicators............................3
Rear Panel Connectors.......................................................4
JetFusion 16/24-Port IAD Family..............................................4
Front Panel Power and Status Indicators............................5
Rear Panel Connectors.......................................................6
Chapter 2 Quick Start Guide
Unpacking the IAD....................................................................9
Installing the IAD ......................................................................9
Connect via Terminal Emulator...............................................10
Setting the Ethernet Port IP Address ................................12
Resetting the IAD ...................................................................14
Connecting via Telnet .............................................................15
Running Telnet ..................................................................15
Using the Menu Interface .......................................................16
2000-A2-GB20-10 - i - February 2004
Basic IAD Configur-ation ........................................................19
Connecting LAN, WAN, USI and Telephones.........................19
Ethernet LAN Connection .................................................19
WAN Connections.............................................................19
USI Connection (16/24-Port) ............................................20
Telephone Connections.....................................................20
Confirming Proper Setup........................................................21
Chapter 3 Administration
IAD Security............................................................................23
RADIUS Server Settings ........................................................26
Setting Up SNMP ...................................................................28
Using the SNMP Configuration Menu ...............................28
Upgrading the System............................................................32
Setting up Your LAN Connection............................................34
Using System Utilities.............................................................35
Managing Configuration Files ...........................................37
Using the File System.............................................................39
Using the Debug Menu...........................................................41
Performing File Transfers.......................................................43
Using File Transfer Utilities ...............................................44
Setting Derived Timing Options ..............................................46
Verifying an IP Address ..........................................................47
Verifying an IP Address for Windows Systems .................47
Verifying the IAD IP Addresses.........................................47
Chapter 4 WAN Configuration
Basic WAN Setup Tasks.........................................................48
Using the WAN Configuration Menu.......................................52
Selecting the Datalink Protocol...............................................53
Setting Up TDM Voice ............................................................54
Selecting the Physical Interface .............................................55
2000-A2-GB20-10 - ii - February 2004
Configuring the G.SHDSL Interface........................................56
Configuring the SDSL Interface—JF2100 ..............................59
Configuring the SDSL Interface..............................................60
Configuring the ADSL Interface..............................................64
Setting the Interface to T1 or E1.............................................65
Configuring the T1 Interface...................................................66
Configuring the E1 Interface...................................................71
Configuring ATM PVCs...........................................................75
Adding a PVC....................................................................75
Modifying a PVC ...............................................................78
Deleting a PVC..................................................................83
Showing Current PVCs .....................................................84
Configuring
ATM Options .....................................................................84
Configuring
Frame Relay DLCIs...........................................................86
Modifying a DLCI...............................................................87
Adding a DLCI...................................................................88
Deleting a DLCI.................................................................90
Displaying Current DLCIs..................................................90
Configuring
Frame Relay Options ........................................................90
Quick Configuration................................................................95
Chapter 5 Router Configuration
Basic Router Setup Tasks ......................................................97
Router Configuration Menu ....................................................98
Configuring
a Port IP Address..............................................................98
Unconfiguring a Port IP Address..........................................100
Setting the Port Maximum Transmission Unit ......................101
Enabling and Disabling RIP..................................................101
Enabling and Disabling RIP Poisoned Reverse by Port.. 101
Setting the RIP Version ...................................................102
2000-A2-GB20-10 - iii - February 2004
Managing Static and Default Routes ....................................103
Setting the Default Route .....................................................105
Configuring DNS Client ........................................................106
Configuring DHCP Client......................................................107
Configuring DHCP Relay......................................................108
Configuring the Telnet Server Port .......................................109
Configuring IP Filtering.........................................................109
Configuring IP Header Compression (IPHC)........................ 116
Configuring the LAN IP Broadcast Destination..................... 116
Displaying the Route Table................................................... 116
Chapter 6 Bridge Configuration
Basic Bridge Setup Tasks..................................................... 119
Bridge Configuration Menu...................................................120
Enabling and Disabling Bridging...........................................120
IP Over Bridging..............................................................120
Enabling or Disabling Bridging Globally ..........................121
Enabling or Disabling Bridging by Port............................121
Setting the Bridge Aging Timer.............................................122
Enabling and Disabling STP.................................................123
Enabling or Disabling STP Globally ................................123
Enabling or Disabling STP by Port..................................123
Configuring Spanning Tree Bridge Priority ...........................124
Configuring Spanning Tree Port Priority...............................124
Configuring Spanning Tree Hello Time.................................125
Configuring Spanning Tree Maximum Age ...........................125
Configuring Spanning Tree Forward Delay ..........................125
Configuring Spanning Tree Path Cost..................................125
Deleting a Bridge Forwarding Database Entry .....................126
Chapter 7 Voice Path Configuration
Basic Voice Path Setup Tasks..............................................127
2000-A2-GB20-10 - iv - February 2004
Voice Path Configuration Menu............................................128
Setting the Voice Gateway ...................................................128
Setting Jitter Delay ...............................................................130
Displaying Jitter Delay..........................................................130
Setting Start Mode................................................................130
Setting SLIC Control Mode...................................................132
Setting Compander Mode.....................................................132
Set On Hook Transmission Mode.........................................133
Setting Idle Voltage Mode.....................................................133
Setting Debug Mode.............................................................134
Configuring Echo Cancellation.............................................134
Setting Loop Gain.................................................................135
Setting Country Mode...........................................................137
Managing MGCP Embedded Client .....................................138
Managing Copper-Com Call Control ....................................142
JetStream Call Control Settings............................................144
Configuring AAL2/LES CAS .................................................146
Configuring for AAL2/LES CAS.......................................146
Configuring AAL2/LES CCS-ELCP ......................................150
Chapter 8 Firewall Configuration
Creating a Firewall via IP Filtering........................................154
Chapter 9 DHCP Server Configuration
Basic DHCP Server Setup Tasks .........................................155
The DHCP Server Configur-ation Menu...............................156
Using DHCP Debugging Messages .....................................156
Enabling and Disabling DHCP Server..................................156
Enabling and Disabling Checking for Additional DHCP Servers157
Configuring DHCP Server Parameters.................................157
Configuring
the DHCP Address Range Pool......................................158
2000-A2-GB20-10 - v - February 2004
Configuring a DHCP Client Entry .........................................158
Displaying DHCP Server Details ..........................................160
Displaying DHCP Server Statistics.......................................161
Displaying DHCP Server Assigned and Unassigned Addresses161
Displaying DHCP Entry Details ............................................162
Deleting a DHCP Client Entry...............................................162
Deleting a DHCP Assign-ment Entry....................................162
Chapter 10 Multicast Configuration
Configuring Multicast............................................................163
Enabling and Disabling Global IP Multicast..........................164
Configuring PIM—Dense Mode by Port ...............................164
Managing Multicast Route Source........................................165
Adding a Multicast Routing Source ......................................165
Removing a Multicast Routing Source .................................166
Displaying the Multicast Routing Source..............................166
Displaying the IGMP Group..................................................166
Displaying the IGMP Querier................................................167
Displaying the Multicast Routing Table.................................167
Displaying the PIM Neighbor................................................168
Chapter 11 NAT Configuration
The NAT Configuration
Menu ...............................................................................170
Enabling NAT Translation.....................................................171
Configuring
NAT Local Server ............................................................172
Configuring
NAT Timeouts..................................................................173
Configuring
the NAT Port Range ........................................................174
Configuring
the NAT Alias Entry .........................................................175
NAT Statistics .......................................................................176
2000-A2-GB20-10 - vi - February 2004
NAT Connection Table..........................................................177
NAT Connection Details .......................................................177
NAT Local Server Table........................................................179
NAT Alias Table ....................................................................179
Deleting IP Addresses from NAT Tables ..............................179
Deleting a NAT Local Server Entry.......................................180
Deleting a NAT Alias Entry ...................................................180
Chapter 12 IAD Reports
The Report Menu..................................................................181
Current Configur-ation Report ..............................................182
Network Statistics Reports....................................................184
Interface Statistics Reports...................................................193
Media Statistics Reports .......................................................205
Route Table Report...............................................................217
ARP Table Report.................................................................217
Bridge Forwarding Database Report ....................................217
Bridge Status Report ............................................................218
PPP Authorization Entries Report ........................................218
System Uptime Report .........................................................219
Memory Statistics Reports....................................................219
Zero All Statistics..................................................................220
Chapter 13 Command Line Interface
Intro-duction..........................................................................221
set wan stp bridge ................................................................221
Command Line Interface Reference.....................................223
exit........................................................................................223
ping.......................................................................................223
quit........................................................................................223
rename file............................................................................223
reset system .........................................................................224
2000-A2-GB20-10 - vii - February 2004
remove lan ip address ..........................................................224
set bridge global ...................................................................224
set bridge stp global .............................................................225
set dhcp server enable .........................................................225
set dhcp server gateway.......................................................225
set dhcp server subnet .........................................................225
set dhcp server dns ..............................................................225
set dhcp server netbios ........................................................225
set dhcp server domain ........................................................225
set dhcp server range...........................................................226
set dns server address .........................................................226
set ip default route................................................................226
set ip route............................................................................226
set lan bridge........................................................................227
set lan ip address .................................................................227
set lan rip..............................................................................228
set lan stp bridge ..................................................................228
set mgcp bracketing .............................................................228
set mgcp listening port..........................................................228
set mgcp notified entity.........................................................229
set mgcp signaling connection .............................................229
set mgcp signaling port.........................................................229
set mgcp signaling tos..........................................................229
set mgcp voice connection ...................................................229
set mgcp voice tos................................................................230
set nat...................................................................................230
set sdsl speed.......................................................................231
set system defaults...............................................................231
set wan atm ppp auth...........................................................231
set wan atm vc......................................................................232
set wan bridge ......................................................................232
set wan datalink....................................................................233
set wan framerelay ...............................................................233
2000-A2-GB20-10 - viii - February 2004
set wan ip address................................................................234
set wan stp bridge ................................................................234
set wan rip ............................................................................235
show configuration................................................................235
show dhcp server configuration............................................235
show ip routes ......................................................................235
tftp receive............................................................................235
Chapter 14 Troubleshooting and Diagnostics
Using the Diagnostics
Menu ...............................................................................237
POTS Diagnostics ................................................................237
SDSL Diagnostics.................................................................242
ISDN-BRI Diagnostics ..........................................................243
Troubleshooting the IAD.......................................................244
Chapter 15 Verification
Power-up Test.......................................................................247
Operational Test ...................................................................247
Maintenance.........................................................................248
Displaying the Current Configuration....................................248
Appendix A Menu Map
Menu Map.............................................................................250
Appendix B Country Codes
Country Codes Tables ..........................................................252
Appendix C JetFusion IAD Specifications
Equipment List......................................................................254
2/4/8-Port..............................................................................255
2000-A2-GB20-10 - ix - February 2004
16/24-Port.............................................................................262
Appendix D Connector Pinouts
Connector Pinouts................................................................265
Appendix E Glossary
Glossary ...............................................................................268
Index
2000-A2-GB20-10 - x - February 2004
3UHIDFH
The JetFusion Family IAD User Guide contains the information you need
to install, connect and configure each JetFusion IAD in a customer’s
premises.
Audience This guide is intended for network engineers and other professionals in the
telecommunications industry who are engaged in the installation,
configuration, management and support of telephone and computer
networks, network access products, and related equipment.
Contents The guide contains the following chapters and appendixes:
This preface describes the audience, how this guide is organized,
safeguards you should always observe, and warranty and regulatory
notices.
Chapter 1, Introduction on page 1, introduces the features of the IADs,
including the hardware, indicators and ports.
Chapter 2, Quick Start Guide on page 8, describes the process of getting
an IAD up and running in a typical customer premises. This chapter is
helpful if you are new to IADs, because it lists each step, beginning with
unpacking the IAD. It also provides information about logging on, using the
menu interface, setting the IP address, basic configuration tasks and
restarting the IAD. Once you have read this chapter, you will be wellprepared to use the remaining reference chapters.
Chapter 3, Administration on page 22, provides information about IAD
security, configuring Simple Network Management Protocol (SNMP),
upgrading ACOS, system utilities and other topics.
Chapter 4, WAN Configuration on page 48, details how to configure the
JetFusion IAD for physical connection to the network—T1/E1 and xDSL,
Frame Relay and ATM, and TDM Voice for channelized T1 circuits.
Chapter 5, Router Configuration on page 96 describes the steps to
configure the IAD as a router, including setting IP addresses, static routes,
configuring RIP, DNS Client, DHCP Client and other router settings.
Chapter 6, Bridge Configuration on page 118 , provides details about
setting up the IAD as a bridge, including setting bridging globally or by
port, setting the aging timer, and enabling Spanning Tree support.
Chapter 7, Voice Path Configuration on page 127, describes how to set up
voice ports for use in various DSLAM and voice gateway environments.
2000-A2-GB20-10 - xi - February 2004
Chapter 8, Firewall Configuration on page 154, provides information about
setting up the IAD to perform IP filtering.
Chapter 9, DHCP Server Configuration on page 155, walks you through
the steps required to configure the Dynamic Host Configuration Protocol
(DHCP) server and client.
Chapter 10, Multicast Configuration on page 163, describes the steps to
configure the IAD to perform Network Address Translation (NAT).
Chapter 11, NAT Configuration on page 169, describes the steps required
to configure the IAD to perform Network Address Translation (NAT).
Chapter 12, IAD Reports on page 181, describes each report you can run.
Chapter 13, Command Line Interface on page 221, describes how to enter
and exit CLI mode, and how to use each command in the command line
interface. You may use these commands instead of using the
corresponding commands in the menu interface.
Chapter 14, Troubleshooting and Diagnostics on page 236, shows you
how to troubleshoot and diagnose your IAD configuration when abnormal
symptoms occur in the voice or computer network.
Chapter 15, Verification on page 247, describes the steps you take to
verify normal operation once you’ve installed, connected and configured
the IAD. It also covers maintenance and how to display the current
configuration.
Appendix A, Menu Map on page 250, provides a graphic view of the IAD
menu interface, illustrating its navigation and organization.
Appendix B, Country Codes on page 252, lists the specifications for each
country code supported in the IAD.
Appendix C, JetFusion IAD Specifications on page 254, lists the
specifications for each IAD.
Appendix D, Connector Pinouts on page 265, provides interface pinout
information for each type of port on the IADs.
Safeguards You should read and understand the following precautions and warnings
before using the JetFusion IAD. You should post these precautions in a
clearly visible location near each IAD.
The Safety status of the SLIC ports on this product are defined as TNV
-2. Therefore, cables attached to them should not be subject to over
voltage. To ensure this they should not leave the building in which the
Unit is installed.
Close supervision is necessary when the system is used by or near
children. Do not leave unattended while in use.
Only use electrical extension cords with a current rating equal to that of
the system.
Always disconnect the system from power before cleaning and
servicing and when not in use.
Do not spray liquids directly onto the system when cleaning. Always
apply the liquid first to a static free cloth.
Do not immerse the system in any liquid or place any liquids on it.
2000-A2-GB20-10 - xii - February 2004
Do not disassemble this system (except as instructed in the
LAN LINK LAN ACT WAN LINK VOICEPOWER
manufacturer’s instructions). To reduce the risk of shock and to
maintain the warranty on the system, a qualified technician must
perform service or repair work.
Avoid using this product during an electrical storm. There may be a
remote risk of electric shock from lightning.
Keep ventilation openings free of any obstructions.
SAVE THESE INSTRUCTIONS.
Product Warranty
Each JetFusion IAD is warranted to be free from manufacturer’s defects
for the period of one year from the date of original purchase.
Conventions Some paragraphs display a symbol in the margin. These paragraphs
contain important notes or warnings, or information that is specific to one
or more IADs.
NOTE
CAUTION
JF2104
Information in this style of paragraph is special information
you should be aware of as you proceed with the task at hand.
Information in this style of paragraph indicates important
personal safety information you should heed, or voice
operations that may be interrupted if you continue.
This paragraph alerts you to information that is specific to one
or more IADs, listed immediately to the left of the text.
Regulatory Notices
FCC Notice
All JetFusion products except the JF2004 have been tested and found to
comply with the limits for a Class A digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in
a Commercial environment. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance
with the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely
to cause harmful interference in which case the user will be required to
correct the interference at his own expense.
The JF2004 has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not in-stalled and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
2000-A2-GB20-10 - xiii - February 2004
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by Paradyne could void
the user’s authority to operate this equipment.
The JetFusion models below comply with Part 68 of the FCC Rules. On
the bottom of the base of this equipment is a label that contains, among
other information, the FCC Registration Number and Ringer Equivalence
Number (REN) for the equipment. You must, upon request, provide this
information to your telephone company.
NOTE: REN is not required for some types of analog or digital facilities.
Before connecting your IAD, you must inform the telephone company of
the following information.
IAD SOC/REN USOC FIC
JF2208, JF2216,
JF2224
JF2004, JF2008 REN = 0.0B RJ11C -
An FCC compliant telephone cord and modular plug is provided with this
equipment. This equipment is designed to be connected to the telephone
network or premises wiring using a compatible modular jack that is Part 68
compliant. See installation instructions for details. The REN is useful to
determine the quantity of devices you may connect to your telephone line
and still have all those devices ring when your telephone number is called.
In most, but not all areas, the sum of the RENs of all devices connected to
one line should not exceed five (5). To be certain of the number of devices
you may connect to your line, as determined by the REN, you should
contact your local telephone company to determine the maximum REN for
your calling area.
NOTE: REN is associated with loop-start and ground-start ports. Do not
use for E&M or digital ports.
If your telephone equipment causes harm to the telephone network, the
Telephone Company may discontinue your service temporarily. If possible,
they will notify you in advance. However, if advance notice is not practical,
you will be notified as soon as possible. You will be informed of your right
to file a complaint with the FCC.
SOC = 6.0N RJ48C 04DU9.BN,
04DU9.DN,
04DU9.1KN,
04DU9.1SN
2000-A2-GB20-10 - xiv - February 2004
Your telephone company may make changes in its facilities, equipment,
operations, or procedures that could effect the proper functioning of your
equipment. If they do, you will be notified in advance to give you an
opportunity to maintain uninterrupted telephone service.
If you experience trouble with the IAD, please contact your service
provider for information on obtaining service or repairs. The Telephone
Company may ask that you disconnect this equipment from the network
until the problem has been corrected or until you are sure that the
equipment is not malfunctioning. No user serviceable parts are contained
in this equipment. This equipment may not be used for coin service
provided by the Telephone Company. Connection to party lines is subject
to state tariffs. Contact the state Public Utilities Commission or Corporation
for information. Do not attempt to repair this equipment yourself.
Industry Canada Notice
“NOTICE: The Industry Canada label identifies certified equipment. This
certification means that the equipment meets telecommunications network
protective, operational and safety requirements as prescribed in the
appropriate Terminal Equipment Technical Requirements document(s).
The Department does not guarantee the equipment will operate to the
user's satisfaction.
Before installing this equipment, users should ensure that it is permissible
to be connected to the facilities of the local telecommunications company.
The equipment must also be installed using an acceptable method of
connection. The customer should be aware that compliance with the
above conditions may not prevent degradation of service in some
situations. Repairs to certified equipment should be coordinated by a
representative designated by the supplier. Any repairs or alterations made
by the user to this equipment, or equipment malfunctions, may give the
telecommunications company cause to request the user to disconnect the
equipment.
Users should ensure for their own protection that the electrical ground
connections of the power utility, telephone lines and internal metallic water
pipe system, if present, are connected together. This precaution may be
particularly important in rural areas.
Caution: Users should not attempt to make such connections themselves,
but should contact the appropriate electric inspection authority, or
electrician, as appropriate.”
“NOTICE: The Ringer Equivalence Number (REN) assigned to each
relevant terminal device provides an indication of the maximum number of
terminals allowed to be connected to a telephone interface. The
termination on an interface may consist of any combination of devices
subject only to the requirement that the sum of the Ringer Equivalence
Numbers of all the devices does not exceed 5.”
Underwriters’ Laboratories’ Statement
These systems are intended to be powered only by the power supply unit
provided.
2000-A2-GB20-10 - xv - February 2004
CE Mark
These JetFusion products have been marked with the CE mark. This mark
indicates compliance with EEC Directives 89/336/EEC, 73/23/EEC 1999/
5/EC.
Warning
All JetFusion products except JF2004 are Class A products. In a domestic
environment these products may cause radio interference in which case
the user may be required to take adequate measures
A full copy of the declaration of Conformity can be obtained from Polyspan
Ltd., Whichford House, Parkway Court, Oxford Business Park South,
Oxford, OX4 2JY, UK
Declaration of Conformity:
Hereby, Polyspan Ltd. declares that this JetFusion is in compliance with
the essential requirements and other relevant provisions of Directive
1999/5/EC.
Konformitetserklæring:
Hermed erklærer Polyspan Ltd., at indestående JetFusion er i
overensstemmelse med de grundlæggende krav og de relevante punkter i
direktiv 1999/5/EF.
Konformitätserklärung:
Hiermit erklärt Polyspan Ltd., dass der JetFusion die grundlegenden
Anforderungen und sonstige maßgebliche Bestimmungen der Richtlinie
1999/5/EG erfüllt.
:
, Polyspan Ltd.
JetFusion
1999/5/ K.
Vaatimustenmukaisuusvakuutus:
Polyspan Ltd. vakuuttaa täten, että JetFusion on direktiivin 1999/5/EC
keskeisten vaatimusten ja sen muiden tätä koskevien säännösten
mukainen.
Déclaration de conformité :
Par la présente, Polyspan Ltd. déclare que ce JetFusion est conforme aux
conditions essentielles et à toute autre modalité pertinente de la Directive
1999/5/CE.
Dichiarazione di conformità:
Con la presente Polyspan Ltd. dichiara che il JetFusion soddisfa i requisiti
essenziali e le altre disposizioni pertinenti della direttiva 1999/5/CE.
2000-A2-GB20-10 - xvi - February 2004
Verklaring van overeenstemming:
Hierbij verklaart Polyspan Ltd. dat diens JetFusion voldoet aan de
basisvereisten en andere relevante voorwaarden van EG-richtlijn 1999/5/
EG.
Declaração de Conformidade:
Através da presente, a Polyspan Ltd. declara que este JetFusion se
encontra em conformidade com os requisitos essenciais e outras
disposições relevantes da Directiva 1999/5/CE.
Declaración de conformidad:
Por la presente declaración, Polyspan Ltd. declara que este JetFusion
cumple los requisitos esenciales y otras cláusulas importantes de la
directiva 1999/5/CE.
Överensstämmelseförklaring:
Polyspan Ltd. förklarar härmed att denna JetFusion överensstämmer med
de väsentliga kraven och övriga relevanta stadganden i direktiv 1999/5/
EG.
2000-A2-GB20-10 - xvii - February 2004
,QWURGXFWLRQ
This chapter introduces the JetFusion Integrated Access Devices (IAD)
and describes their hardware and software. You should be aware of the
characteristics of each IAD to properly install and configure them for
operation in a customer’s premises.
This chapter provides information about these topics:
JetFusion 2/4/8-port IAD features, indicators and connectors (page 2)
JetFusion 16/24-port IAD features, indicators and connectors (page 4)
JetFusion IADs are ideal for service providers offering small to medium
businesses (or business units) a high quality voice and data service over
broadband circuits. With up to 24 POTS ports and full LAN support with a
full range of integrated features, each IAD offers toll-quality voice and high
speed Internet access over a single copper pair in one unit.
Each IAD supports any POTS device via its voice subsystem, and any IPbased computer system (Ethernet printers, personal computers—
Windows, Macintosh, Unix, Linux, etc.— network file servers, and other
network devices) via its LAN subsystem.
2/4/8-Port IAD
03-17481
16/24-Port IAD
JetFusion
POWER
LAN
LAN
WAN
VOICE
LINK
DCE
DCE
ACT
LINK
LINK
ACT
03-17482
Figure 1–1. JetFusion Integrated Access Devices
2000-A2-GB20-10 - 1 - February 2004
Data Interfaces
The data connection through the IAD supports IEEE 802.10-compliant
bridging and routing.
When the IAD is configured for routing, it supports Routing Information
Protocol (RIP) version 1, version 2, or static IP routing. The IAD complies
with RFC-1812 when interfacing with Version 4 IP routers.
The WAN subsystem supports the following interfaces:
ATM data transport via xDSL and T1/E1 per RFC 1483 or RFC 2364
Frame Relay data transport via xDSL and T1/E1 per RFC 1490
Frame Relay data transport per RFC 1483 with Q.922 frames
JetFusion 2/4/8-Port IAD Family
The JetFusion 2/4/8-port IAD family provides a highly interoperable,
cost-effective voice and high-speed data integration solution that is
compatible with industry-leading DSLAM and Voice Gateway
manufacturers. These IADs prioritize voice packets and dynamically
allocate bandwidth between voice and data services.
Features
Interoperable with DSLAMs based on Alcatel, Texas Instruments,
MetaLink, and Globespan chip sets. These include Lucent Stinger/
TNT, Nokia Speedlink System, Promatory IMAS, AccessLan
PacketLoop, Accelerated Networks AN-3200, CopperMountain
CopperEdge, and Paradyne GranDSLAM DSLAMs, for example.
Seamless voice and high-speed data integration over xDSL or T1/E1
Supports data rates from 144 Kbps to 2.3 Mbps and customer premise
interfaces including POTS, 10/100BaseT Ethernet, BRI
Compatible with WAN protocols including ATM and Frame Relay
BRI IAD supports ISDN BRI telephone interface
RJ11 POTS interface with Loop Start or Ground Start
Dynamic and static IP routing and bridging capabilities
Firewall support via IP filtering
DHCP and NAT to support IP address management
Management capabilities including Telnet, SNMP and TFTP
IADs in the 2/4/8-port family are characterized by different WAN interfaces,
and different voice capacity:
JF2004 and JF2008 IADs—provide WAN access over ADSL, and
telephone support for 2, 4, or 8 voice ports.
JF2004i/JF2104i IADs—provide voice services and high-speed
Internet or corporate connectivity over ADSL (JF2004i) or G.SHDSL
(JF2104i), plus 4 ISDN Basic Rate Interface (BRI) ports for up to 8
voice extensions.
JF2104 and JF2108 IADs—provide voice services and high-speed
Internet or corporate connectivity over G.SHDSL, and provide 4 or 8
voice ports.
JF2208 IAD—provides WAN access via T1 lines, and provides 8 voice
ports.
2000-A2-GB20-10 - 2 - February 2004
JF2304 and JF2308 IADs—provide voice services and high-speed
Internet or corporate connectivity over SDSL, and provide 4 or 8 voice
ports.
Physical and electrical specifications for each IAD are listed in Appendix
C, JetFusion IAD Specifications on page 254.
Front Panel Power and Status Indicators
The front panel of the IAD contains several LEDs. These LEDS provide
general information about the operational status of the IAD.
Figure 1–2. 2/4/8-Port Family Front Panel Indicators
LAN LINK LAN ACT WAN LINK VOICEPOWER
03-17479
Table 1–1. 2/4/8-Port Family Front Panel Indicators
LED Description
POWER Illuminates when the IAD is powered on.
LAN LINK Illuminates when there is an operational LAN connection
on the Ethernet port.
LAN ACT Flashes when there is activity on the Ethernet port.
WAN LINK Flashes as the IAD is establishing a link, and illuminates
solid when there is a proper connection on the WAN port
and synchronization has been achieved.
VOICE Illuminates when there is activity on the voice ports.
When connected to a Jetstream Voice Gateway, it
remains lit, and blinks when there is activity.
2000-A2-GB20-10 - 3 - February 2004
Rear Panel Connectors
On the rear panel (Figure 1–3), the IAD contains several connectors. The
type and position of the WAN and telephone connectors vary by IAD.
Figure 1–3. Typical 2/4/8-Port Family Back Panel Connectors
Console (DB-9)
Serial Connector
POTS Telephone Lines
RJ-11 Jacks
PWR
Power
Receptacle
CONSOLE
Ethernet (RJ-45)
10/100 LAN
LINE
1 LINE 2 LINE 3 LINE 4
LINE 5 LINE 6 LINE 7 LINE 8
WAN Module
RJ-45 or RJ-48C Jack
WAN
DC Power Adapter
Connects the IAD to any AC outlet of 90-250 volts via an external, 18 volt
power supply.
RS-232 Console Port
Connects the IAD to a PC using a straight through 9-pin serial (DB9 RS-
232) cable, for the purpose of using a terminal emulator for IAD
configuration and management.
10/100Base-T Ethernet Port
Connects the IAD to the local area network using a CAT-5 straight through
Ethernet cable, or directly to a PC for accessing via Telnet (using a crossover cable, customer-supplied).
WAN Interfaces
Depending on the IAD, WAN interfaces include the following:
T1/E1—uses an RJ48 connector for the connection.
G.SHDSL—uses an RJ11 connector for the connection.
SDSL—uses an RJ45 connector for the connection.
ADSL—uses an RJ45 connector for the connection.
Telephone Interfaces
2/4/8-port IADs have varying telephone capacity. These IADs support:
2, 4, or 8 analog telephones via RJ11 POTS ports
—or—
8 telephone extensions via 4 BRI ISDN S0 ports.
JetFusion
16/24-Port
The JetFusion 16/24-port IAD family provides a highly interoperable,
cost-effective broadband solution for voice and high-speed data
integration that is compatible with industry-leading DSLAM and Voice
IAD Family
2000-A2-GB20-10 - 4 - February 2004
Gateway manufacturers. These IADs prioritize voice packets and
dynamically allocate bandwidth between voice and data services.
Features
Interoperable with DSLAMs based on Alcatel, Texas Instruments,
MetaLink, and Globespan chip sets. These include Lucent Stinger/
TNT, Nokia Speedlink System, Promatory IMAS, AccessLan
PacketLoop, Accelerated Networks AN-3200, Coppermountain
CopperEdge, and Paradyne GranDSLAM DSLAMs, for example.
Seamless voice and high-speed data integration over xDSL or T1/ITE1
Supports data rates from 144 Kbps to 2.3 Mbps and customer premise
interfaces including POTS, 10/100BaseT Ethernet
Compatible with WAN protocols including ATM and Frame Relay
RJ21X POTS interface with Loop Start or Ground Start
Universal Serial Interface supports V.35 and EIA-530
Dynamic and static IP routing and bridging capabilities
Firewall support via IP filtering
DHCP and NAT to support IP address management
Management capabilities including Telnet, SNMP and TFTP
16/24-port IADs are characterized by different WAN interfaces and
different voice capacity:
JF2216 IAD—provides WAN access over T1/E1, and telephone
support for 16 voice ports via RJ21X connector.
JF2216c IAD—provides WAN access over channelized T1, and
telephone support for 16 voice ports via RJ21X connector.
JF2316 IAD—provides WAN access over SDSL, and telephone
support for 16 voice ports via RJ21X connector.
Physical and electrical specifications for each IAD are listed in Appendix
C, JetFusion IAD Specifications on page 254.
Front Panel Power and Status Indicators
The front panel of the IAD contains several LEDs. These LEDs provide
general information about the operational status of the IAD.
Figure 1–4. 16/24-Port IAD Front Panel
Front Panel
POWER LAN
LAN
WAN
VOICE
LINK
ACT
LINK
DCE
LINK
Status Indicators
DCE
ACT
03-17483
2000-A2-GB20-10 - 5 - February 2004
Table 1–2. Front Panel LEDs
LED Description
POWER Illuminates when the IAD is powered on.
LAN LINK Illuminates when there is an operational LAN connection
on the Ethernet port.
LAN ACT Flashes when there is activity on the Ethernet port.
WAN LINK Flashes as the IAD is establishing a link, and illuminates
solid when there is a proper connection on the DSL WAN
port and synchronization has been achieved.
VOICE Illuminates when there is activity on the voice ports.
When connected to a Jetstream Voice Gateway, it
remains lit, and blinks when there is activity.
DCE LINK Illuminates when there is a link between the IAD and
data communications equipment (DCE).
DCE ACT Illuminates or blinks when there is activity on the DCE
link.
Rear Panel Connectors
On the rear panel, the IAD contains several connectors. The WAN
connectors vary by IAD—both are present, but one has a permanently
attached metal shield to prevent use.
Figure 1–5. 16/24-Port IAD Back Panel
+ +,,
-.*
/+) 0/1
!
" " # $%
/.
0*
)**
-&-
12 -
0*, 3&'4
!"5 -5
&'(
+-+)
-5
!+0)0)-&)
AC Power
Connects the IAD to an AC outlet of 108-130 volts via an AC power cord.
10/100Base-T Ethernet Port
Connects the IAD to the local area network using a CAT-5 straight through
Ethernet cable, or directly to a PC for accessing via Telnet (using a crossover cable, customer-supplied).
WAN Interfaces
Depending on the IAD, WAN interfaces include the following:
T1/E1—uses an RJ48 connector for the connection.
SDSL—uses an RJ45 connector for the connection.
2000-A2-GB20-10 - 6 - February 2004
Universal Serial Interface (USI) Port
The USI port is configurable for RS-530 or V.35. When configured as an
RS-530 port, you may use a straight through DB25 serial cable for
connection to your leased line DSU/CSU equipment. When configured for
use as V.35, Black Box Corporation provides a cable (FA058) for
conversion purposes. To convert from RS-530 to RS-449, Black Box
provides a cable EDN57J. By notifying you of their availability, Paradyne
neither endorses or recommends these products.
For USI port pinouts when configured as RS-530, V.35 or RS-449, see
Table D–9 on page 267.
RS-232 Console Port
Connects the IAD to a PC, using a straight through 9-pin serial (DB9 RS-
232) cable for the purpose of using a terminal emulator for configuration
and management.
Telephone Interfaces
Each 16/24-Port IAD supports 16 or 24 analog telephones via an RJ11
jack.
2000-A2-GB20-10 - 7 - February 2004
4XLFN6WDUW*XLGH
This chapter describes the steps to install, connect, and set the IP address
of the JetFusion IAD. It introduces the menu interface and describes how
to perform basic configuration for common LAN and WAN environments. It
also describes basic operations—resetting the IAD, and logging off.
In many cases, all the information you need to get an IAD up and running
in a customer’s premises is contained in this single chapter.
This chapter contains the following topics:
Unpacking the IAD (page 9)
Installing the IAD (page 9)
Connecting via Terminal Emulator (page 10)
Resetting the IAD (page 9)
Powering up the IAD (page 10)
Logging on to the IAD (page 11)
Setting the Ethernet port IP address (page 12)
Connecting via Telnet (page 15)
Basic IAD configuration (page 19)
Connecting the LAN, WAN, USI and Telephones (page 19)
Confirming proper setup (page 21)
In most installations, you’ll proceed through these topics in order. If your
situation varies, complete information on installation, connection,
configuration and troubleshooting is contained in the reference chapters
following this chapter.
NOTE
When the IAD prompts you for input, the current value is
displayed in parentheses. To conveniently accept the current
value, just press Enter.
2000-A2-GB20-10 - 8 - February 2004
Unpacking
LAN LINK LAN ACT WAN LINK VOICEPOWER
LAN LINK LAN ACT WAN LINK VOICEPOWER
the IAD
Each IAD is packed and shipped in a durable container. If you haven’t
already done so, open the container and unpack the IAD. Carefully
remove the IAD from the package and packing material.
IAD Package Components
Each IAD is shipped with the components listed below. As you unpack
them, note their condition and identity, and compare the list to the packing
list in the package.
AC power adapter and cord (6 feet long), or AC power cord
Agency Compliance information sheet
Ethernet cable (straight through), 7 feet long
WAN cable (varies by interface), 7 feet long
If you note any visible damage, or components are missing, notify the
shipping company immediately to make a damage claim. Contact the
company from which the IAD was purchased to obtain a Return Material
Authorization (RMA) for return of damaged equipment, or to order missing
components.
Installing the IAD
NOTE
We suggest you keep the shipping container and packing
material for future shipping or storage of the unit.
After you unpack the IAD, find a suitable location to install the IAD in the
customer’s premises. Ideal locations include computer equipment room, or
a telephone or wiring closet. You can locate the IAD in an equipment rack,
on a table or shelf, or it may be wall-mounted. Install the IAD in a location
that is generally protected and the IAD will be undisturbed.
AC Power and Uninterruptible Power Supply
The IAD requires access to AC power (NEMA 15-3R). Make sure the IAD
is located within six feet of an AC power outlet. Locate the nearest power
outlet and plug in the supplied AC power adapter or AC power cord. If
there is an uninterruptible power supply on premises, plug the AC power
adapter or cord into that power source.
Ensure that the power cord conveniently and safely reaches the rear panel
of the IAD where the power plug or adapter jack is located.
2/4/8-Port
16/24-Port
Do not attach the AC power adapter, or power up the unit at
this time.
Plug in the power cord, but do not power up the unit
Clearance Requirements
If you install the IAD horizontally, make sure you maintain at least 2 inches
of horizontal distance from other IADs or other electronic equipment, to
ensure adequate ventilation and heat dissipation. If you install the IAD
2000-A2-GB20-10 - 9 - February 2004
vertically, ensure at least 3 inches of distance between other IADs or other
equipment.
Connect via Terminal Emulator
NOTE
2/4/8-port IADs may be stacked on top of one another, when
mounted horizontally. 16/24-port IADs may be rack mounted.
Wiring Requirements
Make sure that the telephone wiring, LAN and WAN cables reach the IAD
and can be dressed in a manner that is safe for the wiring, does not pull or
create lateral stress on the connectors or ports on the rear of the IAD, and
does not present a trip hazard to personnel working in the vicinity of the
equipment. Do not connect any cables or wiring at this time.
The IAD is configured and managed from either the console or Ethernet
port. Most network engineers use Telnet to access the IAD via Ethernet.
After you use a terminal emulator program via the console port to set the
IP address, you may continue to use a terminal emulator via the console
port if you choose.
NOTE
Before you can connect to the IAD via Telnet, make sure the IP address is
set correctly for this network. To do so, follow the steps, each described in
detail below:
1. Connect the IAD to a PC
2. Log in to the IAD
3. Set the IP address
After a period of inactivity (three minutes by default), the IAD
automatically terminates console-based and Telnet sessions
to maintain security. To change this value, see Configuring
the Console Timeout Period on page 36.
NOTE
Be sure that the IAD and PC are both powered OFF before
connecting the console cable. If both devices are not turned
off when you connect the cables, you may place the IAD in an
unstable state, and you may need to reset one or both
devices before you can perform configuration tasks.
Connect the IAD to a PC
To connect the IAD to a PC via the console port:
1. Turn off both devices and insert the male connector of a DB9 serial
cable into the console port on the IAD.
2. Insert the female connector of the cable into a serial (COM) port on
your PC.
NOTE
See RS-232 DB-9 Console Port Pin Assignments on page
265 for console port specifications.
Power Up the IAD
1. With the console cable connected, on 2/4/8-port IADs plug the AC
power adapter into the IAD. On 16/24-port IADs, turn on the power
2000-A2-GB20-10 - 10 - February 2004
switch, located on the back panel. This starts the IAD and it executes
the boot process to begin normal operation.
2. Verify that the Power indicator on the front panel illuminates.
NOTE
As the IAD boots, it sends status messages to the console
port. If you are connected, you will see the boot sequence
progress.
Log in via a Terminal Emulation Program
With a serial cable connected, follow these steps to log in to the IAD:
1. Open a terminal emulation program (Hyperterminal, for example).
2. Select the COM port to which the IAD is connected.
3. Type or select the following settings and save your changes.
Table 2–1. Terminal Emulator Settings
Setting Value Setting Value
Bits per second 19,200
Data bits 8
Parity None
4. Press Enter. The IAD displays the log in message:
Enter Login ID >
NOTE
If the IAD does not respond, make sure the IAD is powered
up, check the cable and connections, and review the settings.
Stop bits 1
Flow control None
Emulation ANSI or VT100
5. Type the default supervisor level user ID (Supervisor) (or your user
ID if changed) and press Enter. Note that both the user ID and
password are case-sensitive.
Table 2–2 below lists the default user IDs and passwords.
Table 2–2. Default IAD User IDs and Passwords
Security Level User ID Password
User <enter> <Enter>
Network
NetMan <Enter>
Administrator
Supervisor Supervisor supervisor
For information on security levels, and user ID and password management
see IAD Security on page 23.
6. The IAD displays the password message:
Enter Password >
7. Type the default password (supervisor, or your password if
different) and press Enter.
8. If log in is not successful, the IAD displays the following message:
Invalid UserID or Password - Try again
Press any key to continue...
2000-A2-GB20-10 - 11 - February 2004
Loading...