Paradyne 9550 DS3 User Manual
iMarc® 9550 DS3 Probe
Installation Instructions
Document Number 9550-A2-GN10-00
September 2005
Contents
Software and Firmware License Agreement ................................................. 2
Product Documentation Online ..................................................................... 3
Unpacking and Inspecting the Equipment .................................................... 4
Installing the Brackets for Rack Mounting ..................................................... 4
Installing in a Rack ........................................................................................ 5
Connecting to Power ..................................................................................... 6
Connecting the Subscriber Port .................................................................... 8
Connecting to the DS3 Network ................................................................... 9
Connecting the Ethernet Port ....................................................................... 10
Connecting the Modem Port ......................................................................... 11
Connecting the Console Port ........................................................................ 12
Using the Asynchronous Terminal Interface ................................................. 13
Menu Hierarchy ............................................................................................. 14
Saving Configuration Options ....................................................................... 16
EMI Notices .................................................................................................. 17
CE Marking ................................................................................................... 17
Japan Notice ................................................................................................. 17
Important Safety Instructions ........................................................................ 18
Warranty, Sales, Service, and Training Information ...................................... 19
1
Software and Firmware License Agreement
ONCE YOU HAVE READ THIS LICENSE AGREEMENT AND AGREE TO ITS
TERMS, YOU MAY USE THE SOFTWARE AND/OR FIRMWARE INCORPORATED
INTO THE PARADYNE PRODUCT. BY USING THE PARADYNE PRODUCT YOU
SHOW YOUR ACCEPTANCE OF THE TERMS OF THIS LICENSE AGREEMENT.
IN THE EVENT THAT YOU DO NOT AGREE WITH ANY OF THE TERMS OF THIS
LICENSE AGREEMENT, PROMPTLY RETURN THE UNUSED PRODUCT IN ITS
ORIGINAL PACKAGING AND YOUR SALES RECEIPT OR INVOICE TO THE
LOCATION WHERE YOU OBTAINED THE PARADYNE PRODUCT OR THE
LOCATION FROM WHICH IT WAS SHIPPED TO YOU, AS APPLICABLE, AND YOU
WILL RECEIVE A REFUND OR CREDIT FOR THE PARADYNE PRODUCT
PURCHASED BY YOU.
The terms and conditions of this License Agreement (the “Agreement”) will apply to the
software and/or firmware (individually or collectively the “Software”) incorporated into
the Paradyne product (the “Product”) purchased by you and any derivatives obtained
from the Software, including any copy of either. If you have executed a separate written
agreement covering the Software supplied to you under this purchase, such separate
written agreement shall govern.
Paradyne Corporation (“Paradyne”) grants to you, and you (“Licensee”) agree to accept
a personal, non-transferable, non-exclusive, right (without the right to sublicense) to use
the Software, solely as it is intended and solely as incorporated in the Product
purchased from Paradyne or its authorized distributor or reseller under the following
terms and conditions:
1. Ownership: The Software is the sole property of Paradyne and/or its licensors. The
Licensee acquires no title, right or interest in the Software other than the license
granted under this Agreement.
2. Licensee shall not use the Software in any country other than the country in which
the Product was rightfully purchased except upon prior written notice to Paradyne
and an agreement in writing to additional terms.
3. The Licensee shall not reverse engineer, decompile or disassemble the Software in
whole or in part.
4. The Licensee shall not copy the Software except for a single archival copy.
5. Except for the Product warranty contained in the manual, the Software is provided
“AS IS” and in its present state and condition and Paradyne makes no other
warranty whatsoever with respect to the Product purchased by you. THIS
AGREEMENT EXPRESSLY EXCLUDES ALL OTHER WARRANTIES, WHETHER
EXPRESS OR IMPLIED, OR ORAL OR WRITTEN, INCLUDING WITHOUT
LIMITATION:
a. Any warranty that the Software is error-free, will operate uninterrupted in your
operating environment, or is compatible with any equipment or software
configurations; and
2
b. ANY AND ALL IMPLIED WARRANTIES, INCLUDING WITHOUT LIMITATION
IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A
PARTICULAR PURPOSE AND NON-INFRINGEMENT.
Some states or other jurisdictions do not allow the exclusion of implied warranties
on limitations on how long an implied warranty lasts, so the above limitations may
not apply to you. This warranty gives you specific legal rights, and you may also
have other rights which vary from one state or jurisdiction to another.
6. IN NO EVENT WILL PARADYNE BE LIABLE TO LICENSEE FOR ANY
CONSEQUENTIAL, INCIDENTAL, PUNITIVE OR SPECIAL DAMAGES,
INCLUDING ANY LOST PROFITS OR LOST SAVINGS, LOSS OF BUSINESS
INFORMATION OR BUSINESS INTERRUPTION OR OTHER PECUNIARY LOSS
ARISING OUT OF THE USE OR INABILITY TO USE THE SOFTWARE,
WHETHER BASED ON CONTRACT, TORT, WARRANTY OR OTHER LEGAL OR
EQUITABLE GROUNDS, EVEN IF PARADYNE HAS BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES, OR FOR ANY CLAIM BY ANY THIRD
PARTY.
7. The rights granted under this Agreement may not be assigned, sublicensed or
otherwise transferred by the Licensee to any third party without the prior written
consent of Paradyne.
8. This Agreement and the license granted under this Agreement shall be terminated
in the event of breach by the Licensee of any provisions of this Agreement.
9. Upon such termination, the Licensee shall refrain from any further use of the
Software and destroy the original and all copies of the Software in the possession of
Licensee together with all documentation and related materials.
10. This Agreement shall be governed by the laws of the State of Florida, without
regard to its provisions concerning conflicts of laws.
Product Documentation Online
Complete documentation for Paradyne products is available at www.paradyne.com.
Select Support → Technical Manuals. Select:
iMarc SLV Technical Description (9000-A2-GB30-10) – Describes the features,
interfaces, and cables for iMarc SLV CSU/DSUs and routers.
iMarc SLV Configuration Reference (9000-A2-GB31-30) – Lists and describes the
configuration options available for iMarc SLV CSU/DSUs and routers.
iMarc SLV SNMP Reference (9000-A2-GB32-20) – Describes support for MIBs,
SNMP traps, and RMON in iMarc SLV CSU/DSUs and routers.
iMarc SLV Operations Guide (9000-A2-GB33-30) – Explains how to operate and
troubleshoot iMarc SLV CSU/DSUs and routers.
To order a paper copy of a Paradyne document, or to speak with a sales representative,
please call 1-727-530-2000.
3
Unpacking and Inspecting the Equipment
!
HANDLING PRECAUTIONS FOR STATIC-SENSITIVE DEVICES
This product is designed to protect sensitive components from
damage due to electrostatic discharge (ESD) during normal
operation. When performing installation procedures,
however, take proper static control precautions to
prevent damage to equipment. If you are not sure
of the proper static control precautions, contact
your nearest sales or service representative.
The following components should be included in your package:
®
1 – iMarc
2 – Brackets for use in a 19-inch rack
2 – Brackets for use in a 23-inch rack
4 – Right-angle BNC adapters
2 – BNC Cables, 18 inches long
2 – BNC Cables, 30 inches long
2 – BNC Cables, 25 feet long
If there is visible damage, do not attempt to connect the device. Contact your sales
representative.
9550 DS3 Probe
Installing the Brackets for Rack Mounting
The Probe can be installed in a rack using mounting brackets. Two brackets suitable for
a 19-inch (48.3 cm) rack and two brackets suitable for a 23-inch (58.4 cm) Bay Networks
or Nortel rack are shipped with the unit.
Procedure
To install the mounting brackets for rack mounting:
1. Locate the black screw nearest the front panel on each side of the unit.
2. Remove these two black screws (one from each side) before attempting to install
the mounting brackets.
3. Identify six flat-head screws (for 19-inch racks) or six machine screws (for 23-inch
racks) provided with the mounting brackets in the hardware kit.
4. Attach the brackets appropriate to your rack size. Tighten all screws firmly.
4
19-inch (483 mm) Rack Mount
23-inch (584 mm) EIA and Bay Networks
Rack Mount
05-17709
23-inch (584 mm) Nortel
Rack Mount
Installing in a Rack
Two types of mounting screws are provided. Use:
#10-32 mounting screws for rails with threaded screw holes
#12-24 mounting screws and self-retaining nuts for rails with unthreaded screw
holes
Procedure
To install the Probe in a rack:
1. Determine where in the rack you will mount the Probe. If your rack does not have
threaded screw holes, slip self-retaining nuts onto the rails where the Probe will be
fastened.
2. Place the unit so that the brackets rest against the front of the rails. Insert screws in
the bottom screw positions and hand-tighten them.
5
3. Insert and tighten the screws in the top screw positions, then tighten the bottom
screws.
Connecting to Power
The Probe requires a 120 VAC, 60 Hz power source.
Procedure
To connect the 9550 DS3 Probe to power:
1. Connect a ground wire to the grounding screw on the front of the Probe.
SUBSCRIBER
YEL
AIS
LOS
OOF
LCV
RD
RX
TD
NETWORK
TX
ATMC
ATMS
9550 DS3
Ground
2. Connect the other end of the wire to an earth ground.
6
05-17707
Loading...