Paradox SR150 User Manual
Red
Blue
Clear
Lenses
Amber
SR150 Wireless Siren w/Built-In Strobe Light
1
3
5
6
7
8
9
10
4
2
Overview
Description
The SR150 is a weatherproof, stand-alone, fully supervised outdoor wireless
siren with built-in strobe light and wireless transceiver. The SR150 uses 2-way
wireless communication, which provides continuous supervision between the
panel and siren with fast response to alarm signals within four seconds.
With its tough weatherproof construction, the SR150 operates reliably
from -30ºC to 50ºC (-22ºF to 122ºF) when using alkaline batteries or power
supply.
With normal use, the SR150 will function up to 3 years without the need to
replace the batteries (battery life can be extended by using an optional AC or
DC power supply).
This guide describes how to install and configure the SR150 wireless siren.
Included Items
• 1 strobe lens (available in red, blue, amber, or clear)
•3 D type alkaline batteries
Required/Optional Items
•Mounting hardware
• 8-16VAC, or 9-20VDC external power supply (optional)
Compatibility
• EVOHD v.1.20 or higher
• EVO192 v3.20 or higher
• MG/SP series v4.0 (except SP4000)
• MG6250 v3.0 or higher
• RTX3 v1.5 or higher/ v5.30 for EVO panels
• K32LCD v1.3 or higher
• BabyWare v2.8 or higher/ v2.30 for EVO panels
Features
• Internal protective plastic cover
•Built-in transceiver
• 100dB wireless siren
•Integrated strobe light
• Weather-resistant design using a PC/ABS enclosure with UV
protection
• Fast alarm response time (4 seconds)
• 2.5 hour alarm display (strobe flashes every 4 seconds after bell
• Siren presence supervised by control panel
• Dual tamper protection for cover removal and removal from wall
• Assign up to 4 sirens per control panel
• Firmware upgrade via 307USB
•Siren test mode
SR150-EI14 05/2015 SR150 V2.30 PARADOX.COM
cut-off )
Figure 1: SR150 Overview
Number Overview Description
1
100dB siren
2
Battery pack (3 “D” size alkaline batteries) with gold plated
battery connections or optional 3.6VDC
3
Power supply input (8-16Vac / 9-20VDC)
4
In-field firmware upgrade connector
5
Dual-action tamper switch (detects when cover is removed
and when unit is removed from wall)
6
Internal protective plastic cover
7
Test switch
8
LED status indicators and signal strength (See LED Feedback
below for details)
9
Antenna (can be extended using an RG6 or RG59 coaxial
cable with standard male F connectors. Attach the antenna
using a female/female F adaptor)
10
Strobe lights
LED Feedback
Figure 2: LED Status Indicators
The following table describes LED Status Indicators.
LED
Indicator
TX Sending data
RX Receiving data
PSSI Signal strength siren receives from control panel
Flash 4x - strong signal
Flash 3x - good signal
Flash 2x - weak signal
Flash 1x - very weak signal (relocate)
No flash - no signal
Status Flash once/sec. - processor is on
Flash once/4 sec. - power save mode
Description/Status
Programming
Upgrading Firmware
Program the SR130 either though a supported keypad or through
BabyWare software (BabyWare).
Programming with Keypads
Featu re Program
MG6250 MG/SP EVO192/HD
Sections
correspond to
sirens 1 - 8
Learn Siren
Sections correspond to sirens 1- 4.
EXAMPLE: [0802]: Learn Siren 2 for
MG6250
[0801] - [0804] [683] - [686] [2851] - [2858]
Press and hold the Reset/Training switch for 3
seconds after entering the section to learn the siren.
WAR NIN G: When pressing the Reset/Training switch,
the SR130 squawks and the strobe light flashes five
times to confirm siren registration to the panel
Assign
Partition to
- - [2861] - [2868]
Siren
Display Signal
[0801] - [0804] [687] - [690] [2871] - [2878]
Strength
Press and hold the Reset/Training switch for 3
seconds after entering the section to display the
siren signal strength that the panel receives.
Requires keypad K32LCD V1.3 or higher
Label Siren
Te mp o ra r y
[0811] - [0814] [691] - [694] -
Labels identify sirens when reporting events (for MG/
SP only: via e-mail through the IP100/ IP150. For
MG6250 through SMS personal reporting) and for
troubleshooting purposes. Maximum 16 characters
[0800] [695] [2870]
Tamper Switch
Deactivation
for
Maintenance
Press [ENTER] after entering the section to
deactivate tamper alarm until the cover is reinstalled
or after 30 minutes
Panel
Supervision of
[0820]
[587]
-
Siren
: Enabled (default)
ON
OFF: Disabled
The control panel supervises the presence of the
SR150. If lost, the control panel follows global
supervision options set in the control panel
Programming with BabyWare
1. Open BabyWare > Connect your Account.
2. In the Main window: Select the Add Item button > Wireless Sirens.
3. Fill-in the SR150 label, location and serial number.
4. Select Save.
Upgrade SR150 firmware through the Paradox In-Field software (V3.0 or
higher) using the 307USB Direct Connect Interface. The SR130 requires the
batteries installed in order to upgrade the firmware.
Note: Ensure that the SR150 is awake before upgrading the firmware.
To wake up the siren: press the Test button (see connector #7 in
Figure 1). The siren provides a 60 second delay in order to begin
the update.
1. Remove the front cover.
2. Connect the 307USB to the In-Field connector (see connector #4 in
Figure 1).
3. Upgrade according to the firmware upgrade instructions: Go to
www.paradox.com >Software > In-Field Firmware Upgrade
Instructions.
Tamper Supervision
If a tamper is detected, the SR150 will sound an alarm and the strobe light
will flash for 4 minutes. The control panel will follow the global supervision
options set in the panel.
Specifications
Specification Description
Power 4.5Vdc (3 “D” size alkaline batteries)
Optional: 8-16Vac / 9-20Vdc external power
Battery life Up to 3 years based on normal use (e.g. 2 alarms
per year with strobe for 2.5 hours and 8 squawks
per day at an average of 25
power source will extend battery life
Consumption Sleep: 22uA, Standby: 130uA, Alarm: 550mA
RF frequency 433MHz or 868MHz
Siren 100dB (1 meter)
Dimensions 24cm X 6.cm X 18cm (9.5in X 2.3in X 7in)
Operating
Tem p er at ur e
RF range 70m (229ft)
Battery only: -30ºC to 50ºC (-22ºF to 122ºF)
ºC (77ºF). Using optional
Certifications
CE EN 50131-4 Grade 2 EN 50130-5 Class IV
Warranty
For complete warranty information on this product, please refer to the
Limited Warranty Statement found on the Statement. Your use of the
Paradox product signifies your acceptance of all warranty terms and
conditions. Please ensure that your use of the Paradox product is in
compliance with local, national, and international laws.
© 2015 Paradox Security Systems (Bahamas) Ltd. All rights reserved.
Specifications may change without prior notice. US, Canadian and
international patents may apply. BabyWare and Paradox are a trademarks
or registered trademarks of Paradox Security Systems (Bahamas) Ltd. or
its affiliates in Canada, the United States and/or other countries.
SR150-EI14 05/2015 SR150 V2.30 PARADOX.COM
Loading...