PARADOX PRT3 c последовательным и параллельным портами DIGIPLEX-CBUS-EP00-eng.pdf

APR-PRT3 Printer Module:

C-Bus Programming Instructions

We hope this product performs to your complete satisfaction. Should you have any

questions or comments, please visit www.paradox.com and send us your comments.

Table of Contents

Technical Specifications ................................................................................................................................................1

Installation .....................................................................................................................................................................2

Overview ................................... .......... .......... ...... .......... ......... .......... .......... .......... ..........................................................2

Programming Sections .......... ... ....................................... ... ... .... ... ... ... .... ... ....................................................................2

Serial Port Setup ........................................................................................................................................................... 3

Virtual PGM Programming .............................................................................................................................................3

C-Bus Entry Options ......................................................................................................................................................8

Virtual Input Options ....................................................................................................................................................15

PGM Activation Event ......................................................................... .... ... ... ...............................................................22

PGM Deactivation Option ............................................................................................................................................22

PGM Deactivation Event .................................... ... .... ... ... ... ... .... ... ... ... .... ... ..................................................................22

PGM Programming Table ............................................................................................................................................22

Technical Specifications

Parallel Port: Minimum 80 column printer
Serial Port: 1 start bit, 8 data bit, no parity and 1 stop bit (8N1)
Input Voltage: 9 -16 Vdc
Current Consumption: 60mA maximum
Serial Port Baud Rates: 2400, 9600, 19200 or 57600 bps
Event Buffer: 2048 events
Compatibility: EVO48 / EVO96 / EVO192 control panels

DGP-848 control panel (V4.11 and up)
DGP-NE96 control panel (V1.60 and up)

Introduction

The APR-PRT3 Printer Module can be used as an interface between C-Bus and your Digiplex system. When in home automation mode,
the Printer Module can receive and send commands to and from the C-Bus PC interface and the Digiplex control panel, linking your
building automation capabilities with your security system.

The Printer Module features 30 virtual PGMs for use with its building automation interface capabilities. These PGMs are not related to any
physical output on the module, but operate in the same manner and are programmed in the same way as traditional PGMs. A virtual PGM
can be used to trigger a response within C-Bus based on an event that has occurred within the Digiplex system. For example, when a user
uses the Digiplex system to disarm an area, this event could activate a virtual PGM on the Printer Module and trigger a response within C­Bus, such as turning on a specific light on the premises. See “Virtual PGM Programming ” on page 4.

Up to 30 C-Bus entries can be associated with the Pri nter Module’s virtual PGMs. C-Bus entries allow you to set the commands that will be
sent on the C-Bus in relation to events that occur within the Digiplex system. When the state of a virtual PGM on the Printer Module
changes, a message is sent by the C-Bus entry that is associated with that virtual PGM. See “C-Bus Entry Options” on page 8.

The Printer Module also features 16 onboard virtual inputs. These inputs are not related to any physical input on the mod ule, but operate in
the same manner and are programmed in the same way as a traditional zone input. A virtual input can be programmed to trigger a response
from the Digiplex control panel based on an event that has occurred within C-Bus. Using virtual inp ut s to trigger event s within th e Digiplex
control panel involves associating the Printer Module’s virtual input to a zone or a keyswitc h on the control p anel. See “V irtual Input Options”
on page 15.

In order for C-Bus and the Digiplex control panel to communicate in such a way, the Printer Module’s serial port must be set to
communicate using the Clipsal C-Bus Protocol.

For a complete list of the Printer Module’s event reporting features, see the Printer Module V1.0 (APR-PRT3) Instructions.

The APR-PRT3 Printer Module is compatible with C-Bus interface firmware V4.00.00 and higher. C-Bus lighting units must be
configured with firmware V1.1 and higher.

If the Printer Module fails to connect to the C-Bus PC interface, a trouble will be generated.

1

Installation

The Printer Module is connected to the control panel’s combus. Connect the four terminals labeled red , black, green, and yel low of the
module to the corresponding terminals on the control panel as shown in Figure 2 on page 21. See the EVO or DGP-848 Reference &
Installation Manual for the maximum allowable installation dist an ce from the control panel.

The C-Bus PC Interface must be connected to the Printer Module’s serial port using a null modem cable only.

Overview

The following provides of an overview of how the Printer Module communicates with C-Bus.

Figure 1: C-Bus Overview

• C-Bus entries are associated with
Printer Module’s virtual PGMs.

• Printer Module sends messages to
C-Bus PC interface based on

• Messages from C-Bus PC
interface can be used to
open/close virtual inputs on
the Printer Module.

virtual PGM events and C-Bus
Entry programming.

Programming Sections

The following describes the programming sections which must be set in order for the Printer Mod ule to act as an interface between a
Digiplex control panel and a C-Bus PC interface.

To access the Printer Module’s programming mode:

1. Press and hold the [0] key.

2. Enter the [

3. Enter section [953] (DGP-848) / [4003] (EVO).

4. Enter the Printer Module’s 8-digit [

5. Enter the 3-digit [

6. Enter the required data.
The Printer Module can also be programmed using the WinLoad Security Software (V2.62 or higher) or using the control p a nel’ s Mo dule

Broadcast feature. Refer to the EVO or DGP-848 Reference & Installation Manual for more details. Please note that th e seri al numb er can
be located on the Printer Module’s PC board.

INSTALLER CODE].

SERIAL NUMBER].

SECTION] you want to program.

2

Serial Port Setup

The following lists the serial port programming options wh ich must be set in order for the Printer Module to commun icat e with C-Bus.

Section [016] - Option [1]

Enable Serial Port

When this option is ON (enabled), you can connect the C-Bus PC interface directly to the Printer Module’s serial port (9 pins) through the
use of a null modem cable. Set option [4] to ON when using the Printer Module as an interface between a C-Bus PC interface and the
Digiplex system.

Section [016] - Options [2] & [3]

Baud Settings

When a C-Bus PC interface is connected to the Printer Module, the serial port baud rate is automatically set to 9600 bau d. Any other baud
rate will be overridden.

Section [016] - Option [4]

Serial Port Usage

This option allows you to set the Printer Module’s serial port usage to either Event Re porting or Home Automation. Set option [4] to ON to
set the Printer Module to Home Automation.

Section [016] - Options [5] & [6]

Home Automation Options

This option allows you to select the home automation protocol for the Printe r Module. Set
option [5] to ON and option [6] to OFF to select the Clipsal C-Bus Protocol.

For more information on the ASCII Protocol, see the ASCII Protocol Programming
Instructions on our website at paradox.com.

Sections [070] to [072]

C-Bus Applications

These sections allow you to enable which C-Bus application(s) the Printer Module can use to send and receive commands. Note that the
Printer Module supports communication with the following three C-Bus applications:

Section Application Hexadecimal Value

[070] __ /__
[071] __ /__

[072] __ /__ C-Bus Security Application $DO

Refer to the appropriate C-Bus documentation for further informatio n on C-Bus ap plication s.

C-Bus lighting Application

C-Bus Air-conditioning

Application

$38

$AC

3

Virtual PGM Programming

The Printer Module supports up to 30 virtual PGMs which are not related to any physical output on the module, but operate in the sa me
manner and are programmed in the same way as traditional PGMs. The tables below of fer an example of the virtual PGM prog ramming
sections which must be set for virtual PGM 1.

Section [100] : Virtual PGM Options

Option OFF ON

[1] and [2] Virtual PGM Deactivation

[3] Virtual PGM Base Time Selection U Seconds N Minutes
[4] Virtual PGM Resend

Section Data Description Default

[101] __/__/__ (000 to 255) x Base Time Virtual PGM 1 Timer 005

Virtual PGM Activation [102] __/__/__ [103] __/__/__ [104] __/__/__ [105] __/__/__

Virtual PGM Deactivation [106] __/__/__ [107] __/__/__ [108] __/__/__ [109] __/__/__

U Message

not resent

Event Group Feature Group Start # End #

Section Section Section Section

N Message

resent

The following describes the programming sections and options specific to the Printer Module’ s virtual PGMs. Use the programming t ables to
document specific settings for all programmed virtual PGMs.

Refer to the table below for a list of the programming sections for all virtual PGMs.

Virtual

PGM

1 [100] - [109]
2 [110] - [119]
3 [120] - [129]
4 [130] - [139]
5 [140] - [149]
6 [150] - [159]

Section

Virtual

PGM

7
8

9
10
11
12

Section

[160] - [169]
[170] - [179]
[180] - [189]
[190] - [199]
[200] - [209]
[210] - [219]

Virtual

PGM

13
14
15
16
17
18

Section

[220] - [229]
[230] - [239]
[240] - [249]
[250] - [259]
[260] - [269]
[270] - [279]

Virtual

PGM

19
20
21
22
23
24

Section

[280] - [289] 25 [340] - [349]
[290] - [299] 26 [350] - [359]
[300] - [309] 27 [360] - [369]
[310] - [319] 28 [370] - [379]
[320] - [329] 29 [380] - [389]
[330] - [339] 30 [390] - [399]

Virtual

PGM

Section

For more informat ion on PGM programming, see “Appendix 1: Programming PGMs” on page 22.

Section [100] - Options [1] and [2]

Virtual PGM Deactivation Option

When the Virtual PGM Activation Event occurs (see “Virtual PGM Activation Event” on p age7), this
option determines when the virtual PGM will return to its normal st ate (d eactiva te ). Dependi ng on the
programmed value, the virtual PGM can stay activated indefinitely. It can also deactivate following a
virtual deactivation event (see “Virtual PGM Deactivation Event” on page7) and/or after the virtual PGM
timer has elapsed (see “Virtual PGM T imers” on page5).

4

U = default setting

Section Virtual PGM [1] OFF / [2] OFF [1] ON / [2] OFF [1] OFF / [2] ON [1] ON / [2] ON

[100] 1 N no deactivation U deactivation event N virtual PGM timer N deactivation event or virtual PGM timer
[110] 2 N no deactivation U deactivation event N virtual PGM timer N deactivation event or virtual PGM timer
[120] 3 N no deactivation U deactivation event N virtual PGM timer N deactivation event or virtual PGM timer
[130] 4 N no deactivation U deactivation event N virtual PGM timer N deactivation event or virtual PGM timer
[140] 5 N no deactivation U deactivation event N virtual PGM timer N deactivation event or virtual PGM timer
[150] 6 N no deactivation U deactivation event N virtual PGM timer N deactivation event or virtual PGM timer
[160] 7 N no deactivation U deactivation event N virtual PGM timer N deactivation event or virtual PGM timer
[170] 8 N no deactivation U deactivation event N virtual PGM timer N deactivation event or virtual PGM timer
[180] 9 N no deactivation U
[190] 10 N no deactivation U deactivation event N virtual PGM timer N deactivation event or virtual PGM timer
[200] 11 N no de activation U deactivation event N virtual PGM timer N deactivation event or virtual PGM timer
[210] 12 N no deactivation U deactivation event N virtual PGM timer N deactivation event or virtual PGM timer
[220] 13 N no deactivation U deactivation event N virtual PGM timer N deactivation event or virtual PGM timer
[230] 14 N no deactivation U deactivation event N virtual PGM timer N deactivation event or virtual PGM timer
[240] 15 N no deactivation U deactivation event N virtual PGM timer N deactivation event or virtual PGM timer
[250] 16 N no deactivation U deactivation event N virtual PGM timer N deactivation event or virtual PGM timer
[260] 17 N no deactivation U deactivation event N virtual PGM timer N deactivation event or virtual PGM timer
[270] 18 N no deactivation U deactivation event N virtual PGM timer N deactivation event or virtual PGM timer
[280] 19 N no deactivation U deactivation event
[290] 20 N no deactivation U deactivation event N virtual PGM timer N deactivation event or virtual PGM timer
[300] 21 N no deactivation U deactivation event N virtual PGM timer N deactivation event or virtual PGM timer
[310] 22 N no deactivation U deactivation event N virtual PGM timer N deactivation event or virtual PGM timer
[320] 23 N no deactivation U deactivation event N virtual PGM timer N deactivation event or virtual PGM timer
[330] 24 N no deactivation U deactivation event N virtual PGM timer N deactivation event or virtual PGM timer
[340] 25 N no deactivation U deactivation event N virtual PGM timer N deactivation event or virtual PGM timer
[350] 26 N no deactivation U deactivation event N virtual PGM timer N deactivation event or virtual PGM timer
[360] 27 N no deactivation U deactivation event N virtual PGM timer N deactivation event or virtual PGM timer
[370] 28 N no deactivation U deactivation event N virtual PGM timer N deactivation event or virtual PGM timer
[380] 29 N no deactivation U deactivation event N
[390] 30 N no deactivation U deactivation event N virtual PGM timer N deactivation event or virtual PGM timer

deactivation event N virtual PGM timer N deactivation event or virtual PGM timer

N virtual PGM timer N deactivation event or virtual PGM timer

virtual PGM timer N deactivation event or virtual PGM timer

Section [101]

Virtual PGM Timers

If the virtual PGM is set to follow its Virtual PGM Timer (see “Virtual PGM Deactivation Option” on page4), the entered value represents the
amount of time that the virtual PGM will remain activated. To program the Virtual PGM Timer, enter a 3-digit value from 000 to 255.
Depending on the Virtual PGM Base Time (see “Virtual PGM Base Time Selection” on page 6), the Virtual PGM Timer will either be in
seconds or minutes.

Section Virtual PGM Data Section Virtual PGM Data

[101] 1 __/__/__ (000 to 255) x Base time [251] 16 __/__/__ (000 to 255) x Base time
[111] 2 __/__/__ (000 to 255) x Base time [261] 17 __/__/__ (000 to 255) x Base time
[121] 3 __/__/__ (000 to 255) x Base time [271] 18 __/__/__ (000 to 255) x Base time
[131] 4 __/__/__ (000 to 255) x Base time [281] 19 __/__/__ (000 to 255) x Base time
[141] 5 __/__/__ (000 to 255) x Base time [291] 20 __/__/__ (000 to 255) x Base time
[151] 6 __/__/__ (000 to 255) x Base time [301] 21 __/__/__ (000 to 255) x Base time
[161] 7 __/__/__ (000 to 255) x Base time [311] 22 __/__/__ (000 to 255) x Base time
[171] 8 __/__/__ (000 to 255) x Base time [321] 23 __/__/__ (000 to 255) x Base time
[181] 9 __/__/__ (000 to 255) x Base time [331] 24 __/__/__ (000 to 255) x Base time
[191] 10 __/__/__ (000 to 255) x Base time [341] 25 __/__/__ (000 to 255) x Base time
[201] 11 __/__/__ (000 to 255) x Base time [351] 26 __/__/__ (000 to 255) x Base time

5

[211] 12 __/__/__ (000 to 255) x Base time [361] 27 __/__/__ (000 to 255) x Base time
[221] 13 __/__/__ (000 to 255) x Base time [371] 28 __/__/__ (000 to 255) x Base time
[231] 14 __/__/__ (000 to 255) x Base time [381] 29 __/__/__ (000 to 255) x Base time
[241] 15 __/__/__ (000 to 255) x Base time [391] 30 __/__/__ (000 to 255) x Base time

Section [100] - Option [3]

Virtual PGM Base Time Selection

If option [3] is OFF, the value programmed for the Virtual PGM Timer will be in secon ds. If option [3] is ON, the Virtual PGM Timer will be in
minutes. U = default setting

Section

[100] 1 U seconds N minutes [250] 16 U seconds N minutes
[110] 2 U seconds N minutes [260] 17 U seconds N minutes
[120] 3 U seconds N minutes [270] 18 U seconds N minutes
[130] 4 U seconds N minutes [280] 19 U seconds N minutes
[140] 5 U seconds N minutes [290] 20 U seconds N minutes
[150] 6 U seconds N minutes [300] 21 U seconds N minutes
[160] 7 U seconds N minutes [310] 22 U seconds N minutes
[170] 8 U seconds N minutes [320] 23
[180] 9 U seconds N minutes [330] 24 U seconds N minutes
[190] 10 U seconds N minutes [340] 25 U seconds N minutes
[200] 11 U seconds N minutes [350] 26 U seconds N minutes
[210] 12 U seconds N minutes [360] 27 U seconds N minutes
[220] 13 U seconds N minutes [370] 28 U seconds N minutes
[230] 14 U seconds N minutes [380] 29 U seconds N minutes
[240] 15 U seconds N minutes [390] 30 U seconds N minutes

Virtual

PGM

[3] OFF [3] ON Section

Virtual

PGM

[3] OFF [3] ON

U seconds N minutes

Section [100] - Option [4]

Virtual PGM Resend Option

If option [4] is ON and a Virtual PGM’s activation event reo ccurs while the virtual PGM is ON, the message sent by the C-Bus entry that is
associated with that virtual PGM will be resent. If option [4] is ON and a Virtual PGM’s deactivation event reoccurs while the virtual PGM is
OFF, the message sent by the C-Bus entry that is associated with that virtual PGM will be resent.

U = default setting

Section

[100] 1 U message not resent N message resent [250] 16 U message not resent N message resent
[110] 2 U message not resent N message resent [260] 17 U message not resent N message resent
[120] 3 U message not resent N message resent [270] 18 U message not resent N message resent
[130] 4 U message not resent N message resent [280] 19 U message not resent N message resent
[140] 5 U message not resent N message resent [290] 20 U message not resent N message resent
[150] 6 U message not resent N message resent [300] 21 U message not resent N message resent
[160] 7 U message not resent N message resent [310] 22 U message not resent N message resent
[170] 8 U message not resent N message resent [320] 23
[180] 9 U message not resent N message resent [330] 24 U message not resent N message resent
[190] 10 U message not resent N message resent [340] 25 U message not resent N message resent
[200] 11 U message not resent N message resent [350] 26 U message not resent N message resent
[210] 12 U message not resent N message resent [360] 27 U message not resent N message resent
[220] 13 U message not resent N message resent [370] 28 U message not resent N message resent
[230] 14 U message not resent N message resent [380] 29 U message not resent N message resent
[240] 15 U message not resent N message resent [390] 30 U message not resent N message resent

Virtual

PGM

[4] OFF [4] ON Section

Virtual

PGM

[4] OFF [4] ON

U message not resent N message resent

6

Sections [102] to [105]

Virtual PGM Activation Event

The Virtual PGM Activation Event determines which event will activate the Printer Module’s virtual PGM output(s). The Event Group
specifies the event, the Feature Group identifies the source, and the Start # and End # set the range within the Feature Group.
Note that Event Groups [064] to [067] may be selected when programming virtual PGMs (see “Appendix 1: Programming PGMs” on
page 22).

Event Group Feature Group Start # End #

Section Section Section Section

Virtual PGM1
Virtual PGM2
Virtual PGM3
Virtual PGM4
Virtual PGM5
Virtual PGM6
Virtual PGM7
Virtual PGM8
Virtual PGM9
Virtual PGM10
Virtual PGM11
Virtual PGM12
Virtual PGM13
Virtual PGM14
Virtual PGM15
Virtual PGM16
Virtual PGM17
Virtual PGM18
Virtual PGM19
Virtual PGM20
Virtual PGM21
Virtual PGM22
Virtual PGM23
Virtual PGM24
Virtual PGM25
Virtual PGM26
Virtual PGM27
Virtual PGM28
Virtual PGM29
Virtual PGM30

[102] __/__/__ [103] __/__/__ [104] __/__/__ [105] __/__/__
[112] __/__/__ [113] __/__/__ [114] __/__/__ [115] __/__/__
[122] __/__/__ [123] __/__/__ [124] __/__/__ [125] __/__/__
[132] __/__/__ [133] __/__/__ [134] __/__/__ [135] __/__/__
[142] __/__/__ [143] __/__/__ [144] __/__/__ [145] __/__/__
[152] __/__/__ [153] __/__/__ [154] __/__/__ [155] __/__/__
[162] __/__/__ [163] __/__/__ [164] __/__/__ [165] __/__/__
[172] __/__/__ [173] __/__/__ [174] __/__/__ [175] __/__/__
[182] __/__/__ [183] __/__/__ [184] __/__/__ [185] __/__/__
[192] __/__/__ [193] __/__/__ [194] __/__/__ [195] __/__/__
[202] __/__/__ [203] __/__/__ [204] __/__/__ [205] __/__/__
[212] __/__/__ [213] __/__/__ [214] __/__/__ [215] __/__/__
[222] __/__/__ [223] __/__/__ [224] __/__/__ [225] __/__/__
[232] __/__/__ [233] __/__/__ [234] __/__/__ [235] __/__/__
[242] __/__/__ [243] __/__/__ [244] __/__/__ [245] __/__/__
[252] __/__/__ [253] __/__/__ [254] __/__/__ [255] __/__/__
[262] __/__/__ [263] __/__/__ [264] __/__/__ [265] __/__/__
[272] __/__/__ [273] __/__/__ [274] __/__/__ [275] __/__/__
[282] __/__/__ [283] __/__/__ [284] __/__/__ [285] __/__/__
[292] __/__/__ [293] __/__/__ [294] __/__/__ [295] __/__/__
[302] __/__/__ [303] __/__/__ [304] __/__/__ [305] __/__/__
[312] __/__/__ [313] __/__/__ [314] __/__/__ [315] __/__/__
[322] __/__/__ [323] __/__/__ [324] __/__/__ [325] __/__/__
[332] __/__/__ [333] __/__/__ [334] __/__/__ [335] __/__/__
[342] __/__/__ [343] __/__/__ [344] __/__/__ [345] __/__/__
[352] __/__/__ [353] __/__/__ [354] __/__/__ [355] __/__/__
[362] __/__/__ [363] __/__/__ [364] __/__/__ [365] __/__/__
[372] __/__/__ [373] __/__/__ [374] __/__/__ [375] __/__/__
[382] __/__/__ [383] __/__/__ [384] __/__/__ [385] __/__/__
[392] __/__/__ [393] __/__/__ [394] __/__/__ [395] __/__/__

Sections [106] to [109]

Virtual PGM Deactivation Event

If the Virtual PGM Deactivation Option is set to follow the Virtual PGM Deactivation Event (see “Virtual PGM Deactivation Option” on
page 4), the virtual PGM will return to its normal state when the event programmed occurs (see t able below). The Event Group specifies the
event, the Feature Group identifies the source, and the Start # and End # set the range within the Feature Group.

Enter the sections that correspond to the Event Group, Feature Group, Start # and End # of the PGM.

Event Group Feature Group Start # End #

Section Section Section Section

Virtual PGM1
Virtual PGM2

[106] __/__/__ [107] __/__/__ [108] __/__/__ [109] __/__/__
[116] __/__/__ [117] __/__/__ [118] __/__/__ [119] __/__/__

7

Virtual PGM3
Virtual PGM4
Virtual PGM5
Virtual PGM6
Virtual PGM7
Virtual PGM8
Virtual PGM9
Virtual PGM10
Virtual PGM11
Virtual PGM12
Virtual PGM13
Virtual PGM14
Virtual PGM15
Virtual PGM16
Virtual PGM17
Virtual PGM18
Virtual PGM19
Virtual PGM20
Virtual PGM21
Virtual PGM22
Virtual PGM23
Virtual PGM24
Virtual PGM25
Virtual PGM26
Virtual PGM27
Virtual PGM28
Virtual PGM29
Virtual PGM30

[126] __/__/__ [127] __/__/__ [128] __/__/__ [129] __/__/__
[136] __/__/__ [137] __/__/__ [138] __/__/__ [139] __/__/__
[146] __/__/__ [147] __/__/__ [148] __/__/__ [149] __/__/__
[156] __/__/__ [157] __/__/__ [158] __/__/__ [159] __/__/__
[166] __/__/__ [167] __/__/__ [168] __/__/__ [169] __/__/__
[176] __/__/__ [177] __/__/__ [178] __/__/__ [179] __/__/__
[186] __/__/__ [187] __/__/__ [188] __/__/__ [189] __/__/__
[196] __/__/__ [197] __/__/__ [198] __/__/__ [199] __/__/__
[206] __/__/__ [207] __/__/__ [208] __/__/__ [209] __/__/__
[216] __/__/__ [217] __/__/__ [218] __/__/__ [219] __/__/__
[226] __/__/__ [227] __/__/__ [228] __/__/__ [229] __/__/__
[236] __/__/__ [237] __/__/__ [238] __/__/__ [239] __/__/__
[246] __/__/__ [247] __/__/__ [248] __/__/__ [249] __/__/__
[256] __/__/__ [257] __/__/__ [258] __/__/__ [259] __/__/__
[266] __/__/__ [267] __/__/__ [268] __/__/__ [269] __/__/__
[276] __/__/__ [277] __/__/__ [278] __/__/__ [279] __/__/__
[286] __/__/__ [287] __/__/__ [288] __/__/__ [289] __/__/__
[296] __/__/__ [297] __/__/__ [298] __/__/__ [299] __/__/__
[306] __/__/__ [307] __/__/__ [308] __/__/__ [309] __/__/__
[316] __/__/__ [317] __/__/__ [318] __/__/__ [319] __/__/__
[326] __/__/__ [327] __/__/__ [328] __/__/__ [329] __/__/__
[336] __/__/__ [337] __/__/__ [338] __/__/__ [339] __/__/__
[346] __/__/__ [347] __/__/__ [348] __/__/__ [349] __/__/__
[356] __/__/__ [357] __/__/__ [358] __/__/__ [359] __/__/__
[366] __/__/__ [367] __/__/__ [368] __/__/__ [369] __/__/__
[376] __/__/__ [377] __/__/__ [378] __/__/__ [379] __/__/__
[386] __/__/__ [387] __/__/__ [388] __/__/__ [389] __/__/__
[396] __/__/__ [397] __/__/__ [398] __/__/__ [399] __/__/__

C-Bus Entry Options

C-Bus entries allow you to set the commands that will be sent on the C-Bus in relation to events that occur wi thin the Digiplex system. When
the state of a virtual PGM on the Printer Module changes, a message is sent by the C-Bus entry that is associated with that virtual PGM. Up
to 30 C-Bus entries can be associated with the Printer Module’s virtual PGMs. Multiple C-Bus entries can be associated with a single virtual
PGM.

The tables below offer an example of th e C-Bu s entry pr ogramming sections which must be set for C-Bu s entry 1.

Section [400] : C-Bus Entry Options

Option OFF ON

[1] Application Selection U Lighting N Air Conditioning

[2] and [3] ON Command

[4] and [5] OFF Command

* Not used with air-conditioning

8

Section Data Description Default

[401] __/__/__ (001 to 030)

[402] __/__/__ (000 to 255)

Virtual PGM
Association

ON Group Address
Variable

000

000

[403] __/__/__ (000 to 015)

[404] __/__/__ (000 to 255) ON Ramp Final Level 000*

[405] __/__/__ (000 to 255)

[406] __/__/__ (000 to 015) OFF Ramp Period 000*

[407] __/__/__ (000 to 255) OFF Ramp Final Level 000*

↓ON Ramp Period

OFF Group Address
Variable

000*

000

*Not used with air-conditioning (values ignored if selected)
Refer to the table below for a list of the programming sections for all virtual PGMs.

C-Bus

Entry

1 [400] - [407] 7 [460] - [467] 13 [520] - [527] 19 [580] - [587] 25 [640] - [647]
2 [410] - [417] 8 [470] - [477] 14 [530] - [537] 20 [590] - [597] 26 [650] - [657]
3 [420] - [427] 9 [480] - [487] 15 [540] - [547] 21 [600] - [607] 27 [660] - [667]
4 [430] - [437] 10 [490] - [497] 16 [550] - [557] 22 [610] - [617] 28 [670] - [677]
5 [440] - [447] 11 [500] - [507] 17 [560] - [567] 23 [620] - [627] 29 [680] - [687]
6 [450] - [457] 12 [510] - [517] 18 [570] - [577] 24 [630] - [637] 30 [690] - [697]

Section

C-Bus

Entry

Section

C-Bus

Entry

Section

C-Bus

Entry

Section

C-Bus

Entry

Section

The following describes the programming sections and options specific to the C-Bus entries. Use the progra mming t ables to docum ent
specific settings for all programmed C-Bus entries.

Section [400] - Option [1]

Application Selection

When option [1] is OFF, C-Bus entries are associated with lighting application. When option [1] is ON, C-Bus entries are associated with
air-conditioning application.

= default setting

U

Section

C-Bus

Entry

[1] OFF [1] ON Section

C-Bus

Entry

[1] OFF [1] ON

[400] 1 U lighting N air-conditioning [550] 16 U lighting N air-conditioning
[410] 2 U lighting N air-conditioning [560] 17 U lighting N air-conditioning
[420] 3 U lighting N air-conditioning [570] 18 U lighting N air-conditioning
[430] 4 U lighting N air-conditioning [580] 19 U lighting N air-conditioning
[440] 5 U lighting N air-conditioning [590] 20 U lighting N air-conditioning
[450] 6 U lighting N air-conditioning [600] 21 U lighting N air-conditioning
[460] 7 U lighting N air-conditioning [610] 22 U lighting N air-conditioning
[470] 8 U lighting N air-conditioning [620] 23

U lighting N air-conditioning
[480] 9 U lighting N air-conditioning [630] 24 U lighting N air-conditioning
[490] 10 U lighting N air-conditioning [640] 25 U lighting N air-conditioning
[500] 11 U lighting N air-conditioning [650] 26 U lighting N air-conditioning
[510] 12 U lighting N air-conditioning [660] 27 U lighting N air-conditioning
[520] 13 U lighting N air-conditioning [670] 28 U lighting N air-conditioning
[530] 14 U lighting N air-conditioning [680] 29 U lighting N air-conditioning
[540] 15 U lighting N air-conditioning [690] 30 U lighting N air-conditioning

9

Section [400] - Options [2] and [3]

ON Commands

This option allows you to choose the type of command that will be sent through the C-Bus entry af ter the st ate of it s associated virtual PGM
changes from OFF to ON. The types of commands include ON, OFF or ramp.

= default setting

U

Section C-Bus Entry [2] OFF / [3] OFF [2] ON / [3] OFF [2] OFF / [3] ON [2] ON / [3] ON*

[400] 1 U none N on N off N ramp
[410] 2 U none N on N off N ramp
[420] 3 U none N on N off N ramp
[430] 4 U none N on N off N ramp
[440] 5 U none N on N off N ramp
[450] 6 U none N on N off N ramp
[460] 7 U none N on N off N ramp
[470] 8 U none N on N off N ramp
[480] 9 U none N on N off N ramp
[490] 10 U none N on N
[500] 11 U none N on N off N ramp
[510] 12 U none N on N off N ramp
[520] 13 U none N on N off N ramp
[530] 14 U none N on N off N ramp
[540] 15 U none N on N off N ramp
[550] 16 U none N on N off N ramp
[560] 17 U none N on N off N ramp
[570] 18 U none N on N off N ramp
[580] 19 U none N on N off N ramp
[590] 20 U none N on N off
[600] 21 U none N on N off N ramp
[610] 22 U none N on N off N ramp
[620] 23 U none N on N off N ramp
[630] 24 U none N on N off N ramp
[640] 25 U none N on N off N ramp
[650] 26 U none N on N off N ramp
[660] 27 U none N on N off N ramp
[670] 28 U none N on N off N ramp
[680] 29 U none N on N off N ramp
[690] 30 U none N on N off N

* Not used with air conditioning

off N ramp

N ramp

ramp

10

Section [400] - Options [4] and [5]

OFF Commands

This option allows you to choose the type of command that will be sent through the C-Bus entry af ter the st ate of it s associated virtual PGM
changes from ON to OFF. The types of commands include ON, OFF or ramp.

= default setting

U

Section C-Bus Entry [4] OFF / [5] OFF [4] ON / [5] OFF [4] OFF / [5] ON [4] ON / [5] ON*

[400] 1 U none N on N off N ramp
[410] 2 U none N on N off N ramp
[420] 3 U none N on N off N ramp
[430] 4 U none N on N off N ramp
[440] 5 U none N on N off N ramp
[450] 6 U none N on N off N ramp
[460] 7 U none N on N off N ramp
[470] 8 U none N on N off N ramp
[480] 9 U none N on N off N ramp
[490] 10 U none N on N
[500] 11 U none N on N off N ramp
[510] 12 U none N on N off N ramp
[520] 13 U none N on N off N ramp
[530] 14 U none N on N off N ramp
[540] 15 U none N on N off N ramp
[550] 16 U none N on N off N ramp
[560] 17 U none N on N off N ramp
[570] 18 U none N on N off N ramp
[580] 19 U none N on N off N ramp
[590] 20 U none N on N off
[600] 21 U none N on N off N ramp
[610] 22 U none N on N off N ramp
[620] 23 U none N on N off N ramp
[630] 24 U none N on N off N ramp
[640] 25 U none N on N off N ramp
[650] 26 U none N on N off N ramp
[660] 27 U none N on N off N ramp
[670] 28 U none N on N off N ramp
[680] 29 U none N on N off N ramp
[690] 30 U none N on N off N

* Not used with air conditioning

off N ramp

N ramp

ramp

Section [401]

Virtual PGM Association

The Virtual PGM Association section allows you to associate a C-Bus entry (or entries) with one of the Printer Module’ s virtual PGMs. Enter

001-030 to individually assign each C-Bus entry to a virtual PGM. Multiple C-Bus entries can be associated with the same virtual PGM.

Section C-Bus Entry Associated PGM Section C-Bus Entry Associated PGM

[401] 1 [551] 16
[411] 2 [561] 17

11

.

[421] 3 [571] 18
[431] 4 [581] 19
[441] 5 [591] 20
[451] 6 [601] 21
[461] 7 [611] 22
[471] 8 [621] 23
[481] 9 [631] 24
[491] 10 [641] 25
[501] 11 [651] 26
[511] 12 [661] 27
[521] 13 [671] 28
[531] 14 [681] 29
[541] 15 [691] 30

Section [402]

ON Group Address Variable

The ON Group Address Variable section allows you to assign which C-Bus group will receive the programmed ON command (see “ON
Commands” on page 10). Enter 000-255 to assign each C-Bus entry to a group address.

For further information on Group Address Variables, refer to the appropriate C-Bus documentation.

Section C-Bus Entry

[402] 1 [552] 16
[412] 2 [562] 17
[422] 3 [572] 18
[432] 4 [582] 19
[442] 5 [592] 20
[452] 6 [602] 21
[462] 7 [612] 22
[472] 8 [622] 23
[482] 9 [632] 24
[492] 10 [642] 25
[502] 11 [652] 26
[512] 12 [662] 27
[522] 13 [672] 28
[532] 14 [682] 29
[542] 15 [692] 30

ON Ramp Period *Not used with air conditioning

The ON Ramp Period section allows you to assign a ramp time value when an ON Ramp command has been set (see “ON Commands” on
page 10). The following table list s the Ramp Period prog rammed value s and their corresp ondin g real-time values.

Ramp Period
Programmed

Value

000 Instant 004 20s 008 90s 012 7min
001 4s 005 30s 009 2min 013 10min
002 8s 006 40s 010 3min 014 15min
003 12s 007 60s 011 5min 015 17min

Real-Time

Value

Ramp Period
Programmed

ON Group Address

Value

Variable

Real-Time

Value

Section C-Bus Entry

Ramp Period
Programmed

Value

Real-Time

Value

Ramp Period
Programmed

ON Group Address

Section [403]*

Value

Variable

Real-Time

Value

12

Enter 000-015 to assign each C-Bus entry an ON Ramp Period.

Section C-Bus Entry ON Ramp Period Section C-Bus Entry ON Ramp Period

[403] 1 [553] 16
[413] 2 [563] 17
[423] 3 [573] 18
[433] 4 [583] 19
[443] 5 [593] 20
[453] 6 [603] 21
[463] 7 [613] 22
[473] 8 [623] 23
[483] 9 [633] 24
[493] 10 [643] 25
[503] 11 [653] 26
[513] 12 [663] 27
[523] 13 [673] 28
[533] 14 [683] 29
[543] 15 [693] 30

Section [404]*

ON Ramp Final Level * Not used with air conditioning

The ON Ramp Final Level section allows you to assign a final level of light intensity when an ON Ramp command has been set (see “ON
Commands” on page 10). Enter 000-255 to assign each C-Bus entry an ON Ramp Fin al Level.

For further information on lighting intensity levels associated with th e ON Ramp command, re fe r to the appro priate C-Bu s
documentation.

Section C-Bus Entry

[404] 1 [554] 16
[414] 2 [564] 17
[424] 3 [574] 18
[434] 4 [584] 19
[444] 5 [594] 20
[454] 6 [604] 21
[464] 7 [614] 22
[474] 8 [624] 23
[484] 9 [634] 24
[494] 10 [644] 25
[504] 11 [654] 26
[514] 12 [664] 27
[524] 13 [674] 28
[534] 14 [684] 29
[544] 15 [694] 30

ON Ramp Final

Level

Section C-Bus Entry

ON Ramp Final

Level

Section [405]

OFF Group Address Variable

The OFF Group Address V ariable section allows you to assi gn which C-Bus gro up will rece ive the pro grammed OFF command (see “OFF
Commands” on page 11). Enter 000-255 to assign each C-Bus entry to a group address.

For further information on Group Address Variables, refer to the appropriate C-Bus documentation.

13

Section C-Bus Entry

[405] 1 [555] 16
[415] 2 [565] 17
[425] 3 [575] 18
[435] 4 [585] 19
[445] 5 [595] 20
[455] 6 [605] 21
[465] 7 [615] 22
[475] 8 [625] 23
[485] 9 [635] 24
[495] 10 [645] 25
[505] 11 [655] 26
[515] 12 [665] 27
[525] 13 [675] 28
[535] 14 [685] 29
[545] 15 [695] 30

OFF Ramp Period * Not used with air conditioning

The OFF Ramp Period section allows you to assign a ramp time value when an OFF Ramp command has been set (see “OFF Commands”
on page 11). Enter 000-015 to assign each C-Bus entry an OFF Ramp Period.

OFF Group

Address Variable

Section C-Bus Entry

OFF Group

Address Variable

Section [406]*

Section C-Bus Entry OFF Ramp Period Section C-Bus Entry OFF Ramp Period

[406] 1 [556] 16
[416] 2 [566] 17
[426] 3 [576] 18
[436] 4 [586] 19
[446] 5 [596] 20
[456] 6 [606] 21
[466] 7 [616] 22
[476] 8 [626] 23
[486] 9 [636] 24
[496] 10 [646] 25
[506] 11 [656] 26
[516] 12 [666] 27
[526] 13 [676] 28
[536] 14 [686] 29
[546] 15 [696] 30

Section [407]*

OFF Ramp Final Level * Not used with air conditioning

The OFF Ramp Final Level section allows you to assign a final level of light intensity when an OFF Ramp comma nd has been set (see “OFF
Commands” on page 11). Enter 000-255 to assign each C-Bus entry an OFF Ramp Final Level.

For further information on lighting intensity levels associated with th e OFF Ramp command , refer to the appropriate C-Bus
documentation.

14

Section C-Bus Entry

OFF Ramp Final

Level

Section C-Bus Entry

OFF Ramp Final

Level

[407] 1 [557] 16
[417] 2 [567] 17
[427] 3 [577] 18
[437] 4 [587] 19
[447] 5 [597] 20
[457] 6 [607] 21
[467] 7 [617] 22
[477] 8 [627] 23
[487] 9 [637] 24
[497] 10 [647] 25
[507] 11 [657] 26
[517] 12 [667] 27
[527] 13 [677] 28
[537] 14 [687] 29
[547] 15 [697] 30

Virtual Input Options

The Print er M o dule features 16 v i r t ua l i np u ts. The virtual inputs’ open/close state can change based on an event that has occurred within
C-Bus. The following describes the programming sections and options specific to the Printer Module’s virtual inputs. Virtual inputs must be
programmed with the appropriate C-Bus application, group address variable and type of command which will cause the virtual input to
react (open/close).

The tables below offer an example of th e virtua l input pr ogramming sections which must be set for virtual input 1.

Section [700] : Virtual Input Options

Option OFF ON

[1] Enabling Virtual Input U Disabled N Enabled
[2] C-Bus Application Selection U Lighting N Air-conditioning

[3] and [4] Virtual Input Close

[5]

Section Data Description Default

[701] __/__/__ (000 to 255) x Base Time Virtual Input 1 Timer 005

[702] __/__/__ (000 to 255)

[703] __/__/__ (000 to 002)

[704] __/__/__ (000 to 255)

[705] __/__/__ (000 to 002)

Virtual Input Base Time

Selection

U Seconds N Minutes

Virtual Input 1 Open
Group Address
Variable

Virtual Input 1 Open
Command

Virtual Input 1 Close
Group Address
Variable

Virtual Input 1 Close
Command

000

000*

000

000*

[706] __/__/__ (000 to 255) Ramp Threshold 000*

15

*Ramp command not used with air conditioning
Refer to the table below for a list of the programming sections for all virtual input s.

Virtual

Input

1 [700] - [706] 5 [740] - [746] 9 [780] - [786] 13 [820] - [826]
2 [710] - [716] 6 [750] - [756] 10 [790] - [796] 14 [830] - [836]
3 [720] - [726] 7 [760] - [766] 11 [800] - [806] 15 [840] - [846]
4 [730] - [736] 8 [770] - [776] 12 [810] - [816] 16 [850] - [856]

Section

Virtual

Input

Section

Virtual

Input

Section

Virtual

Input

Section

The following describes the programming sections and options specific to the Printer Module’ s virtual input s. Use the programming t ables to
document specific settings for all programmed virtual inputs.

Section [700] - Option [1]

Enabling Virtual Input Option

Each virtual input must be individually enabled. Set option [1] to ON to enable the virtual input.

U = default setting

Section

Virtual

Input

[1] OFF [1] ON Section

Virtual

Input

[1] OFF [1] ON

[700] 1 U disabled N enabled [780] 9 U disabled N enabled
[710] 2 U disabled N enabled [790] 10 U disabled N enabled
[720] 3 U disabled N enabled [800] 11 U disabled N enabled
[730] 4 U disabled N enabled [810] 12 U disabled N enabled
[740] 5 U disabled N enabled [820] 13 U disabled N enabled
[750] 6 U disabled N enabled [830] 14 U disabled N enabled
[760] 7 U disabled N enabled [840] 15 U disabled N enabled
[770] 8 U disabled N enabled [850] 16

U disabled N enabled

Section [700] - Option [2]

C-Bus Application Selection

Each virtual input must be programmed to use a specific C-Bus application to monitor C-Bus activity. If option [2] is OFF, lighting
application is used. If option [2] is ON, air-conditioning application is used.

U = default setting

Section

Virtual

Input

[2] OFF [2] ON Section

Virtual

Input

[2] OFF [2] ON

[700] 1 U lighting N air-conditioning [780] 9 U lighti ng N air-conditioning
[710] 2 U lighting N air-conditioning [790] 10 U lighting N air-conditioning
[720] 3 U lighting N air-conditioning [800] 11 U lighting N air-conditioning
[730] 4 U lighting N air-conditioning [810] 12 U lighting N air-conditioning
[740] 5 U lighting N air-conditioning [820] 13 U lighting N air-conditioning
[750] 6 U lighting N air-conditioning [830] 14 U lighting N air-conditioning
[760] 7 U lighting N air-conditioning [840] 15 U lighting N air-conditioning
[770] 8 U lighting N air-conditioning [850] 16

U lighting N air-conditioning

16

Section [700] - Options [3] and [4]

Virtual Input Close Option

The virtual input can be closed by either receiving a virtual input close command, after a timer
elapses or either. This option determines how the virtual input will close.

U = default setting

Section Virtual Input [3] OFF / [4] OFF [3] ON / [4] OFF [3] OFF / [4] ON

[700] 1 U close command N virtual input timer N close command or virtual input timer
[710] 2 U close command N virtual input timer N close command or virtual input timer
[720] 3 U close command N virtual input timer N close command or virtual input timer
[730] 4 U close command N virtual input timer N close command or virtual input timer
[740] 5 U close command N virtual input timer N close command or virtual input timer
[750] 6 U close command N virtual input timer N close command or virtual input timer
[760] 7 U close command N virtual input timer N close command or virtual input timer
[770] 8 U close command N virtual input timer N close command or virtual input timer
[780] 9 U close command N virtual input timer N close command or virtual input timer
[790] 10 U close command N virtual input timer N close command or virtua l input timer
[800] 11 U close command N virtual input timer N close command or virtual input timer
[810] 12 U close command N virtual input timer N close command or virtua l input timer
[820] 13
[830] 14 U close command N virtual input timer N close command or virtua l input timer
[840] 15 U close command N virtual input timer N close command or virtua l input timer
[850] 16 U close command N virtual input timer N close command or virtua l input timer

U close command N virtual input timer N close command or virtual input timer

Section [701]

Virtual Input Timers

If the virtual input is set to follow its Virtua l Input Timer, the entered value represe nt s the amount of ti me th at th e virtual input wi ll remain
open. To program the Virtual Input Timer, enter a 3-digit value from 000 to 255. Depending on the V irtual Input Base T ime (see “Virtual Input
Base Time Selection” on page17), the Virtual Input Timer will either be in seconds or minutes.

Section Virtual Input Timer Data Section Virtual Input Timer Data

[701] 1 __/__/__ (000 to 255) x Base time [781] 9 __/__/__ (000 to 255) x Base time
[711] 2 __ /__ /__ (000 to 255) x Base time [791] 10 __/__/__ (000 to 255) x Base time
[721] 3 __/__/__ (000 to 255) x Base time [801] 11 __/__/__ (000 to 255) x Base time
[731] 4 __/__/__ (000 to 255) x Base time [811] 12 __/__/__ (000 to 255) x Base time
[741] 5 __/__/__ (000 to 255) x Base time [821] 13 __/__/__ (000 to 255) x Base time
[751] 6 __/__/__ (000 to 255) x Base time [831] 14 __/__/__ (000 to 255) x Base time
[761] 7 __/__/__ (000 to 255) x Base time [841] 15 __/__/__ (000 to 255) x Base time
[771] 8 __/__/__ (000 to 255) x Base time [851] 16 __/__/__ (000 to 255) x Base time

Section [700] - Option [5]

Virtual Input Base Time Selection

If option [5] is OFF, the value programmed for the Virtual Input Timer will be in seconds. If op tion [5] is ON, the Virtual Input Timer will be in
minutes. The following table lists the base time sections and their respecti ve virtual inputs.

17

U = default setting

Section

[700] 1 U seconds N minutes [780] 9 U seconds N minutes
[710] 2 U seconds N minutes [790] 10 U seconds N minutes
[720] 3 U seconds N minutes [800] 11 U seconds N minutes
[730] 4 U seconds N minutes [810] 12 U seconds N minutes
[740] 5 U seconds N minutes [820] 13 U seconds N minutes
[750] 6 U
[760] 7 U seconds N minutes [840] 15 U seconds N minutes
[770] 8 U seconds N minutes [850] 16 U seconds N minutes

Virtual Input Open Group Address Variable

The Virtual Input Open Group Address Variable section allows you to set which C-Bus group will cause a virtual input on the Printer Module
to open. Enter 000-255 to assign which group address variable will trigger a virtual input to open.

For further information on Group Address Variables, refer to the appropriate C-Bus documentation.

Virtual

Input

[5] OFF [5] ON Section

seconds N minutes [830] 14 U seconds N minutes

Virtual

Input

[5] OFF [5] ON

Section [702]

Section Virtual Input

[702] 1 [782] 9
[712] 2 [792] 10
[722] 3 [802] 11
[732] 4 [812] 12
[742] 5 [822] 13
[752] 6 [832] 14
[762] 7 [842] 15
[772] 8 [852] 16

Virtual Input Open Command

The Virtual Input Open Command section sets the state of a virtual input to open wh en an ON, OFF or Ramp command occurs within C­Bus. The open command is based on the Open Group Addre ss Variable and on the C-Bus application selected above. Enter 000 to set the
virtual input to open in response to an ON command, 001 to set the virtual input to open in response to an OFF command or 002 to set the
virtual input to open in response to a Ramp command.

Section

[703] 1 U 000 N 001 N 002 [783] 9 U 000 N 001 N 002
[713] 2 U 000 N 001 N 002 [793] 10 U 000 N 001 N 002
[723] 3 U 000 N 001 N 002 [803] 11 U 000 N 001 N 002
[733] 4 U 000 N 001 N 002 [813] 12 U 000 N 001 N 002
[743] 5 U 000 N 001 N 002 [823] 13 U 000 N 001 N 002
[753] 6 U 000 N 001 N 002 [833] 14 U 000
[763] 7 U 000 N 001 N 002 [843] 15 U 000 N 001 N 002
[773] 8 U 000 N 001 N 002 [853] 16 U 000 N 001 N 002

* Not used with air conditioning

Virtual

Input

ON OFF Ramp* Section

Open Group

Address Variable

Section Virtual Input

Virtual

Input

ON OFF Ramp*

Open Group

Address Variable

Section [703]

U = default setting

N 001 N 002

18

Section [704]

Virtual Input Close Group Address Variable

The Virtual Input Open Group Address Variable section allows you to set which C-Bus group will cause a virtual input on the Printer Module
to close. Enter 000-255 to assign which group address variable will trigger a virtual input to close.

For further information on Group Address Variables, refer to the appropriate C-Bus documentation.

Section Virtual Input

[704] 1 [784] 9
[714] 2 [794] 10
[724] 3 [804] 11
[734] 4 [814] 12
[744] 5 [824] 13
[754] 6 [834] 14
[764] 7 [844] 15
[774] 8 [854] 16

Virtual Input Close Command

The Virtual Input Close Command section sets the state of a virtual input to close when an ON , OFF or Ramp command occurs withi n C­Bus. The close command is based on the Close Group Address Variable and on the C-Bus application selected above. Enter 000 to set the
virtual input to close in response to an ON command, 001 to set the virtual input to close in response to an OFF command or 002 to set the
virtual input to close in response to a Ramp command.

Section

[705] 1 U 000 N 001 N 002 [785] 9 U 000 N 001 N 002
[715] 2 U 000 N 001 N 002 [795] 10 U 000 N 001 N 002
[725] 3 U 000 N 001 N 002 [805] 11 U 000 N 001 N 002
[735] 4 U 000 N 001 N 002 [815] 12 U 000 N 001 N 002
[745] 5 U 000 N 001 N 002 [825] 13 U 000 N 001 N 002
[755] 6 U 000 N 001 N 002 [835] 14 U 000
[765] 7 U 000 N 001 N 002 [845] 15 U 000 N 001 N 002
[775] 8 U 000 N 001 N 002 [855] 16 U 000 N 001 N 002

* Not used with air conditioning

Virtual

Input

ON OFF Ramp* Section

Close Group

Address Variable

Section Virtual Input

Virtual

Input

ON OFF Ramp*

Close Group

Address Variable

Section [705]

U = default setting

N 001 N 002

Section [706]*

Ramp Threshold * Not used with air conditioning

The Ramp Threshold section allows you to set a threshold level to Ramp commands occurring within C-Bus. To open a virtu al input, the
Ramp’s Final Level must be greater or equal to the threshold value. To close a virtual input, the Ramp’s Final level must be lower th an the
threshold value. Enter 000-255 to set the virtual input’ s threshold level.

Section Virtual Input Ramp Threshold Section Virtual Input Ramp Threshold

[706] 1 [786] 9
[716] 2 [796] 10
[726] 3 [806] 11
[736] 4 [816] 12
[746] 5 [826] 13
[756] 6 [836] 14
[766] 7 [846] 15
[776] 8 [856] 16

19

Section [900]

Security Report

Security reports are messages sent between the APR-PRT3 and the C-Bu s. Messages that are rece iv ed by the C-Bus can be used to
trigger automated events.

Section Data Description Default

[900] __/__/__ (001 to 008)† Partition affected by security application 001

Section

901

Report Options OFF ON

[1] Global Security report* N = Disable U = Enable
[2]

System Armed / Disarmed

N = Disable U = Enable

[3] Entry / Exit delay N = Disable U = Enable
[4] Zone in alarm / Zone in alarm restore (zones 01 to 80)‡ N = Disable U = Enable
[5] Fire Alarm / Fire Alarm Restore N = Disable U = Enable
[6] Silent Alarm Report / Silent Alarm Restore N = Disable U = Enable
[7] Panic Alarm N = Disable U = Enable
[8] Future use N = N/A U =N/A

* If Global Security report is disabled, all options in sections [901] and [902] will also be disabled.

Section

902

Report Options OFF ON

[1] Low Battery / Low Battery Restored (zones 01 to 80)‡ N = Disable U = Enable
[2] AC Failure / AC Failure restore N = Disable U = Enable
[3] Ready to arm / Not ready to arm N = Disable U = Enable
[4] Zone open / Zone ok (zones 01 to 80)‡ N = Disable U = Enable
[5] Zone tamper / Zone tamper restore (zones 01 to 80)‡ N = Disable U = Enable
[6] Zone Bypassed (zones 01 to 80)‡ N = Disable U = Enable
[7] User Code entered on Keypad N = Disable U = Enable
[8] TLM T rouble/TLM Trouble Restore N

= Disable U = Enable

Section

903

Messages from C-Bus OFF ON

[1] Arm system* N = Forbid U = Allow
[2] Raise alarm** N = Forbid U = Allow
[3] C-Bus tamper / C-Bus tamper restore*** N = Forbid U = Allow
[4] Future use N = N/A U =N/A
[5] Future use N = N/A U =N/A
[6] Future use N = N/A U =N/A
[7] Future use N = N/A U =N/A
[8] Future use N = N/A U =N/A

†

EVO96 allows 8 partitions, Digiplex 848 allow 4 partitions.

‡ Due to C-Bus limitation, only zones 01 from zones 80 can be reported, C-Bus Network will ignore all others.

*

Must enable One-touch regular arming option in the control panel.

**

Alarm will be raised as a Panic Alarm to chosen partitions.

***

Tamper from C-Bus will be reported as a Printer tamper.

20

Figure 2: .APR-PRT3 Connection

Remove AC power and battery before adding a module to the sytem.
Refer to the Digiplex DGP-848 or DGP-NE96 Reference and Installation Manual for the maximum

allowable installation distance from the control panel.

Printer cable length must not exceed 25ft.

For information on using the printer Module as an interface with home automation modules, see the ASCII Protocol
programming instructions or C-BUS Programming instructions.

1. Green “RX” LED: Flashes when the Printer Module is receiving data through the serial port only.

2. Red “TX” LED: Flashes when the Printer Module is transmitting data through the serial port only.

3. 25-Pin Parallel Port: Connect the Printer Module’s 25-pin parallel port to any dot matrix printer.
Note: The dot matrix printer must support a minimum of 80 columns.

4. 9-Pin Serial Port: Connect the Printer Module’s 9-Pin serial port to a dot matrix printer.
Note: The dot matrix printer must support a minimum of 80 columns.

5. 9-pin Serial Port: Connect the Printer Module’s 9-pin serial port to a home automation module.

6. 9-pin Serial Port: Connect C-Bus to the Printer Module using a null modem cable.

7. 9-pin Serial Port: Connect either the Printer Module’s USB or 9-pin serial port to a computer’s COM port to view the control panel’s
events on the computer’s monitor. The events display on the monitor can then be printed through the printer connected to the
computer.

21

Appendix 1: Programming PGMS

A PGM is a programmable output that toggles to its opposite st ate (i .e. a no rmally open PGM will close) when a specific e vent occ urs in the
system. For example, a PGM can be used to reset smoke detectors, activate strobe lights, open/close garage doors and much more.

PGM Activation Event

The PGM Activation Event determines which event from what source will activate the PGM. The Event Group specifies the event, the
Feature Group identifies the source, and the Start # and End # sets the range within the Feature Group (see PGM Programming Table
below).

For example, the APR-PRT3 can activate Virtual PGM1 when the a rea is armed by User Access Codes 256 to 26 0. Therefore:
Event Group section [102] = 010 “Arming with User Code”
Feature Group section [103] = 001 “User Codes 256 to 511”
Start # section [104] = 000 (representing user code 256)
End # section [105] = 004 (representing user code 260)

Enter the sections that correspond to the Event Group, Feature Group, Start # and End # of the desired PGM and enter the data as required.

PGM Deactivation Option

Once the PGMs are activated, they can deactivate when another event occurs or after a period of time. The PGM D eactivati on Option
determines which method is used, the PGM Deactivation Event or the PGM Timer. Enter the section that corresponds to the desired PGM
and enable or disable the option.

PGM Deactivation Event

When the PGM Deactivation Option (see above) is disabled, the PGM Deactivation Event determines which event from what source will
return the PGM to its original state. T he Event Grou p specifies the event, the Feature Grou p identifies the source, and the Start # and End #
determine the range within the Feature Group. The complete PGM Programming Table appears below.

For example, the APR-PRT3 can deactivate Virtual PGM1 when zone 3 opens. Therefore:
Event Group section [106] = 001 “Zone is Open”
Feature Group section [107] = 000 “Zone Numbers”
Start # section [108] = 003
End # section [109] = 003

Enter the sections that correspond to the Event Group, Feature Group, Start # and End # of the desired PGM and enter the data as required.

PGM Programming Table

Event Group Featu re Group Start # End #

PGM Activation

Event

PGM Deactivation

Event

Event

Group

000 Zone is OK
001 Zone is Open 001 to 096 001 to 096
002 Zone is Tampered 001 to 096 001 to 096
003 Zone is in Fire Loop Trouble 001 to 096 001 to 096

PGM __/__/__ __/__/__ __/__/__ __/__/__

PGM __/__/__ __/__/__ __/__/__ __/__/__

Event Feature Group Feature Start # End #

001 to 096 001 to 096

000

255 = any Zone #

Zone Numbers

22

Event

Group

004 Non-reportable Event

005

006 User/Card Access on door

007 Bypass Programming Access

008 TX Delay Zone Alarm

009 Arming with Master

010 Arming with User Code

011 Arming with Keyswitch

User Code entered on
Keypad

Event Feature Group Feature Start # End #

TLM Trouble (see NOTE 3 on

page 28)

Smoke detector reset 001 001

Arm with no entry delay 002 002

Arm in Stay mode 003 003

Arm in Away mode 004 004

Full arm when in Stay mode 005 005

000

255 Any non-reportable event Not Used Not Used
000 User Codes 000 to 255 000 to 255 000 to 255
001 User Codes 256 to 511 000 to 255 000 to 255
002 User Codes 512 to 767 000 to 255 000 to 255
003 User Codes 768 to 999 000 to 231 000 to 231
255 Any User Code Not Used Not Used
000 Door Numbers 001 to 032 001 to 032
255 Any door number Not Used Not Used
000 One-touch Bypass Programming 000 000
000 User Codes 001 to 255 001 to 255 001 to 255
001 User Codes 256 to 511 000 to 255 000 to 255
002 User Codes 512 to 767 000 to 255 000 to 255
003 User Codes 768 to 999 000 to 231 000 to 231
255 Any User Code Not Used Not Used
000 Zone Numbers 001 to 096 001 to 096
255 Any zone number Not Used Not Used
000 User Codes 001 to 255 001 to 255 001 to 255
001 User Codes 256 to 511 000 to 255 000 to 255
002 User Codes 512 to 767 000 to 255 000 to 255
003 User Codes 768 to 999 000 to 231 000 to 231
255 Any User Code Not Used Not Used
000 User Codes 001 to 255 001 to 255 001 to 255
001 User Codes 256 to 511 000 to 255 000 to 255
002 User Codes 512 to 767 000 to 255 000 to 255
003 User Codes 768 to 999 000 to 231 000 to 231
255 Any User Code Not Used Not Used
000 Keyswitch numbers 001 to 032 001 to 032
255 Any keyswitch number Not Used Not Used

Voice mo dule access 006 006

Remote control access 007 007

PC Fail to communicate 008 008

Midnight 009 009

NEware User Login 010 010

NEware User Logout 011 011

User Initiated Callup 012 012

Force Answer 013 013

Force Hangup 014 014

000 000

23

Event

Group

012 Special Arming

013 Disarm with Master

014 Disarm with User Code

015 Disarm with Keyswitch

016

017

018

019 Alarm Cancelled with Master

020

021

Disarm after alarm with
Master

Disarm after alarm with User
Code

Disarm after alarm with
Keyswitch

Alarm Cancelled with User
Code

Alarm Cancelled with
Keyswitch

Event Feature Group Feature Start # End #

Auto Arming 000 000

Arming by WinLoad 001 001

Late to Close 002 002

000

255 Any special arming event Not Used Not Used
000 User Codes 001 to 255 001 to 255 001 to 255
001 User Codes 256 to 511 000 to 255 000 to 255
002 User Codes 512 to 767 000 to 255 000 to 255
003 User Codes 768 to 999 000 to 231 000 to 231
255 Any User Code Not Used Not Used
000 User Codes 001 to 255 001 to 255 001 to 255
001 User Codes 256 to 511 000 to 255 000 to 255
002 User Codes 512 to 767 000 to 255 000 to 255
003 User Codes 768 to 999 000 to 231 000 to 231
255 Any User Code Not Used Not Used
000 Keyswitch numbers 001 to 032 001 to 032
255 Any keyswitch Not Used Not Used
000 User Codes 001 to 255 001 to 255 001 to 255
001 User Codes 256 to 511 000 to 255 000 to 255
002 User Codes 512 to 767 000 to 255 000 to 255
003 User Codes 768 to 999 000 to 231 000 to 231
255 Any User Code Not Used Not Used
000 User Codes 001 to 255 001 to 255 001 to 255
001 User Codes 256 to 511 000 to 255 000 to 255
002 User Codes 512 to 767 000 to 255 000 to 255
003 User Codes 768 to 999 000 to 231 000 to 231
255 Any User Code Not Used Not Used
000 Keyswitch numbers 001 to 032 001 to 032
255 Any keyswitch Not Used Not Used
000 User Codes 001 to 255 001 to 255 001 to 255
001 User Codes 256 to 511 000 to 255 000 to 255
002 User Codes 512 to 767 000 to 255 000 to 255
003 User Codes 768 to 999 000 to 231 000 to 231
255 Any User Code Not Used Not Used
000 User Codes 001 to 255 001 to 255 001 to 255
001 User Codes 256 to 511 000 to 255 000 to 255
002 User Codes 512 to 767 000 to 255 000 to 255
003 User Codes 768 to 999 000 to 231 000 to 231
255 Any User Code Not Used Not Used
000 Keyswitch numbers 001 to 032 001 to 032
255 Any keyswitch Not Used Not Used

No Movement Arming 003 003

Partial Arming 004 004

One-touch Arming 005 005

Future Use 006 006
Future Use 007 007

(InTouch) Voice Module Arming 008 008

24

Event

Group

022 Special Disarm Events

023 Zone Bypassed
024 Zone in Alarm 001 to 096 001 to 096
025 Fire Alarm 001 to 096 001 to 096
026 Zone Alarm Restore 001 to 096 001 to 096
027 Fire Alarm Restore 001 to 096 001 to 096

028 Early to Disarm by User

029 Late to Disarm by User

030 Special Alarm

031 Duress Alarm by User

032 Zone Shutdown
033 Zone Tamper 001 to 096 001 to 096
034 Zone Tamper Restore 001 to 096 001 to 096
035 Special Tamper 000 Keypad Lockout 000 000

Event Feature Group Feature Start # End #

Auto Arm Cancelled 000 000

One-touch Stay/Instant Disarm 001 001

Disarming with WinLoad 002 002

Disarming with WinLoad after

alarm

000

255 Any special disarm event Not Used Not Used

000

255 = any zone #

000 User Codes 001 to 255 001 to 255 001 to 255
001 User Codes 256 to 511 000 to 255 000 to 255
002 User Codes 512 to 767 000 to 255 000 to 255
003 User Codes 768 to 999 000 to 231 000 to 231
255 Any User Code Not Used Not Used
000 User Codes 001 to 255 001 to 255 001 to 255
001 User Codes 256 to 511 000 to 255 000 to 255
002 User Codes 512 to 767 000 to 255 000 to 255
003 User Codes 768 to 999 000 to 231 000 to 231
255 Any User Code Not Used Not Used

000

255 Any special alarm event Not Used Not Used
000 User Codes 001 to 255 001 to 255 001 to 255
001 User Codes 256 to 511 001 to 255 001 to 255
002 User Codes 512 to 767 001 to 255 001 to 255
003 User Codes 768 to 999 001 to 231 001 to 231
255 Any User Code Not Used Not Used

000

255 = any zone #

WinLoad cancelled alarm 004 004

Future Use 005 005
Future Use 006 006
Future Use 007 007

(InTouch) Voice Module

Disarming

Zone Numbers

Emergency Panic (Keys 1 & 3) 000 000

Medical Panic (Keys 4 & 6) 001 001

Fire Panic (Keys 7 & 9) 002 002

Recent Closing 003 003

Police Code 004 004

Global Shutdown 005 005

Zone Numbers

003 003

008 008

001 to 096 001 to 096

001 to 096 001 to 096

25

Event

Group

036 Trouble Event

037 Trouble Restore

038 Module Trouble

039 Module Trouble Restore

040
041 Low Battery on Zone

042 Zone Supervision Trouble 001 to 096 001 to 096
043

044

Fail to Communicate on
telephone Number

Low Battery on Zone
Restored

Zone Supervision Trouble
Restored

Event Feature Group Feature Start # End #

TLM Trouble (see NOTE 2 on

page 28)

AC Failure 001 001

Battery Failure 002 002

000

255 Any trouble event Not Used Not Used

000

255 Any trouble restore event Not Used Not Used

000

255 Any module trouble Not Used Not Used

000

255 Any module trouble restore event Not Used Not Used
000 Telephone Number 001 to 004 001 to 004
255 Any telephone number Not Used Not Used

000

255 = any Zone #

Auxiliary Current Limit 003 003

Bell Current Limit 004 004

Bell Absent 005 005

Clock Trouble 006 006

Global Fire Loop 007 007

TLM Trouble 000 000

AC Failure 001 001

Battery Failure 002 002

Auxiliary Current Limit 003 003

Bell Current Limit 004 004

Bell Absent 005 005

Clock Trouble 006 006

Global Fire Loop 007 007

Combus Fault 000 000

Module Tamper 001 001

ROM/RAM error 002 002

TLM Trouble 003 003

Fail to Communicate 004 004

Printer Fault 005 005

AC Failure 006 006

Battery Failure 007 007

Auxiliary Failure 008 008

Combus Fault 000 000

Module Tamper 001 001

ROM/RAM error 002 002

TLM Trouble 003 003

Fail to Communicate 004 004

Printer Fault 005 005

AC Failure 006 006

Battery Failure 007 007

Auxiliary Failure 008 008

Zone Numbers

000 000

001 to 096 001 to 096

001 to 096 001 to 096

001 to 096 001 to 096

26

Event

Group

Event Feature Group Feature Start # End #

Power up after total power down 000 000

Software reset (Watchdog) 001 001

Test Report 002 002

Future Use 003 003

WinLoad In (connected) 004 004

045 Special Events

000

WinLoad Out (disconnected) 005 005

Installer in programming 006 006

Installer out of programming 007 0 07

255 Any special event Not Used Not Used
000 User Codes 001 to 255 001 to 255 001 to 255
001 User Codes 256 to 511 000 to 255 000 to 255

046 Early to Arm by User

002 User Codes 512 to 767 000 to 255 000 to 255
003 User Codes 768 to 999 000 to 231 000 to 231
255 Any User Code Not Used Not Used
000 User Codes 001 to 255 001 to 255 001 to 255
001 User Codes 256 to 511 000 to 255 000 to 255

047 Late to Arm by User

002 User Codes 512 to 767 000 to 255 000 to 255
003 User Codes 768 to 999 000 to 231 000 to 231
255 Any User Code Not Used Not Used

048 Utility Key

049 Request for Exit

000
255

Utility Key 001 to 064

Any Utility Key

†*

†*

001 to 064 001 to 064

Not Used Not Used

001 to 032 001 to 032

050 Access Denied 001 to 032 001 to 032
051 Door Left Open Alarm 001 to 032 001 to 032
052 Door Forced Alarm 001 to 032 001 to 032

000

255 = any Door

Number

Door Numbers

053 Door Left Open Restore 001 to 032 001 to 032
054 Door Forced Open Restore 001 to 032 001 to 032

055 Intellizone Triggered

056
057
058

059

060 - 061

Zone Excluded on Force
Arming

Zone Went Back to Arm Status
New Module Assigned on

Combus
Module Manually Removed

From Combus
Future Use

255 = Any Module

000 Zone Numbers 001 to 096 001 to 096
255 Any zone number Not Used Not Used

000

255 = Any Zone

000

Zone Numbers 001 to 096 001 to 096
Zone Numbers 001 to 096 001 to 096

Module Address 001 to 254 001 to 254

Module Address 001 to 254 001 to 254

Future Use Future Use Future Use Future Use

000 User Codes 001 to 255 001 to 255 001 to 255
001 User Codes 256 to 511 000 to 255 000 to 255

062 Access Granted to User

002 User Codes 512 to 767 000 to 255 000 to 255
003 User Codes 768 to 999 000 to 231 000 to 231
255 Any User Code Not Used Not Used
000 User Codes 001 to 255 001 to 255 001 to 255
001 User Codes 256 to 511 000 to 255 000 to 255

063 Access Denied to User

002 User Codes 512 to 767 000 to 255 000 to 255
003 User Codes 768 to 999 000 to 231 000 to 231
255 Any User Code Not Used Not Used

†: see page 28

: see page 28

*

27

Event

Group

Event Feature Group Feature Start # End #

Armed 000 000

Force Armed 001 001

Stay Armed 002 002

064 Status 1

See Note 1

on page 28

Instant Armed 0 03 003

Strobe Alarm 004 004

Silent Alarm 005 005

Audible Alarm 006 006

Fire Alarm 007 007

Ready 000 000

Exit Delay 001 001

Entry Delay 002 002

System in Trouble 003 003

Alarm in Memory 004 004

065 Status 2

See Note 1

on page 28

Zones Bypassed 005 005

Bypass, Master , Installer

Programming

006 006

Keypad Lockout 007 007

Intellizone Delay Engaged (see

Note 4 on page 28)

000 000

Fire Delay Engaged 001 001

Auto Arm 002 002

066 Status 3

See Note 1

on page 28

Arming with Voice Module (set

until Exit Delay finishes)

003 003

Tamper 004 004
Zone Low Battery 005 005
Fire Loop Trouble 006 006

Zone Supervision Trouble 007 007

067 Future Use Future Use Future Use Future Use Future Use

NOTE 1:000 = Occurs in all areas enabled in the system (refer to the appropriate control panel Programming Guide).
001 = Area 1003 = Area 3 005 = Area 5 (EVO96 only)007 = Area 7 (EVO96 only)
002 = Area 2004 = Area 4 006 = Area 6 (EVO96 only)008 = Area 8 (EVO96 only)
255 = Occurs in at least one area enabled in the system.

NOTE 2:This TLM trouble event can only be used with EVO96 control panels that have one dialler.
NOTE 3:This TLM trouble event can only be used with DGP-848 control panels or EVO96 control panels that have one dialer.
NOTE 4:This event cannot be used for a module’s PGM programming.

:If a Keyswitch Input is used, the input must be defined as “Generates a Utility Key Event on Open” or “Generates a Utility Key Event on

*

Open and Close”. If a remote control is used, the remote control button must be defined as a Utility Key button.

†

:Actions that Activate a Utility Key Event:

Actions

Utility Key Event

Keypad Utility Keys

Utility Key Event 1 [1] & [2] KS** Input 1 opens KS** Input 1 opens
Utility Key Event 2 [4] & [5] KS** Input 2 opens KS** Input 1 closes
Utility Key Event 3 [7] & [8] KS** Input 3 opens KS** Input 2 opens
Utility Key Event 4 [CLEAR] & [0] or [*] & [0] KS** Input 4 opens KS** Input 2 closes

Keyswitch Inputs

(definition = [3])

Keyswitch Inputs

(definition = [4])

Remote Control

Utility Key 1 RC button
Utility Key 2 RC button
Utility Key 3 RC button
Utility Key 4 RC button

‡
‡
‡
‡

28

Actions

Utility Key Event

Keypad Utility Keys

Utility Key Event 5 [2] & [3] KS** Input 5 opens KS** Input 3 opens

Keyswitch Inputs

(definition = [3])

Keyswitch Inputs

(definition = [4])

Remote Control

Utility Key 5 RC button
Utility Key Event 6 [5] & [6] KS** Input 6 opens KS** In put 3 closes N/A
Utility Key Event 7 [8] & [9] KS** Input 7 opens KS** Input 4 opens N/A
Utility Key Event 8 [0] & [ENTER] or [0] & [#] KS** Input 8 opens KS** Input 4 closes N/A
Utility Key Event 9 N/A KS** Input 9 opens KS** Input 5 opens N/A

Utility Key Event 10 N/A KS** Input 10 opens KS** In put 5 closes N/A
Utility Key Event 11 N/A KS** Input 11 opens KS** Input 6 opens N/A
Utility Key Event 12 N/A KS** Input 12 opens KS** In put 6 closes N/A
Utility Key Event 13 N/A KS** Input 13 opens KS** Input 7 opens N/A
Utility Key Event 14 N/A KS** Input 14 opens KS** In put 7 closes N/A
Utility Key Event 15 N/A KS** Input 15 opens KS** Input 8 opens N/A
Utility Key Event 16 N/A KS** Input 16 opens KS** In put 8 closes N/A
Utility Key Event 17 N/A KS** Input 17 opens KS** Input 9 opens N/A
Utility Key Event 18 N/A KS** Input 18 opens KS** In put 9 closes N/A

iN/AiiN/A
Utility Key Event 31 N/A KS** Input 31 opens KS** Input 16 opens N/A
Utility Key Event 32 N/A KS** Input 32 opens KS** Input 16 closes N/A
Utility Key Event 33 N/A N/A KS** Input 17 opens N/A
Utility Key Event 34 N/A N/A KS** Input 17 closes N/A

i N/A N/A i N/A
Utility Key Event 63 N/A N/A KS** Input 32 opens N/A
Utility Key Event 64 N/A N/A KS** Input 32 closes N/A

‡

** Keyswitch

‡

Refer to the Magellan™ Reference and Installation Manual for remote control button programming instructions.

Warranty
Paradox Security Systems Ltd. (“Seller”) warrants its products to be free from defects in materials and workmanship under normal use for a period of one year. Except as specifically stated herein, all express or
implied warranties whatsoever, statutory or otherwise, including without limitation, any implied warranty of merchantability and fitness for a particular purpose, are expressly excluded. Because Seller d oe s no t
install or connect the products and because the products may be used in conjunction with products not manufactured by Seller, Seller cannot guarantee the performance of the security system and sh all no t b e
responsible for circumstances resulting from the product’s inab ility to o perate. Seller obligation and liability under this warranty is expressly limited to repairing or replacing, at Seller's option, any product not
meeting the specifications. Returns must include proof of purchase and be within the warranty period. In no event shall the Seller be liable to the buyer or any other person for any loss or damages whether direct
or indirect or consequential or i nci de ntal, including without limitation, any damages for l ost pr of i t s stolen goods, or claims by any other party, caused by defective goods or otherwise arisi n g fr o m the i mpr ope r,
incorrect or otherwise faulty installation or use of the merchandise sold.

Notwithstanding the preceding paragraph, the Seller’s maximum liability will be strictly limited to the purchase price of the defective product. Your use of this p rodu ct sig nifies your a ccep t a nce of this wa rr an ty.
BEWARE: Dealers, installers and/or others selling the product are not authorized to modify this warranty or make additional warranties that are binding on the Seller.

© 2003-2007 Paradox Security Systems Lt d. All rights reserved. Specificati ons ma y ch ang e wi th ou t pr i or n oti ce . On e o r m ore o f the following US patents may apply: 6215399, 6111256, 5751803, 5721542,
5287111, 5119069 , 5 07 754 9, 5920259, 5886632. Canadian and international patents may also apply.

Digiplex is a trademark or registered trademar k of Paradox Security Syste ms Ltd. or its af filiates in Canada, the United St ates and/or other countries. Windows® is a registered trademark of Microsoft corporation.
Procomm™ is a trademark of Datasto rm Technologies Inc.. Telix© - Copyright© 1986-1996 by DeltaComm Development & ELSA. HyperTerminal® is a registered trademark of Hilgraeve Inc..
C-Bus is a trademark of Clipsal Integrated Systems Pty Ltd..

For technical support in Canada or the U.S., call 1-800-791-1919, Monday to Friday from 8:00 a.m.

to 8:00 p.m. EST. For techni cal sup port outsi de Canada an d the U .S ., call 00-1-450-491-7444,

Monday to Friday from 8:00 a.m. to 8:00 p.m. EST. Please feel free to visit our website at

www.parado x.com.

Printed in Canada 04/2007 paradox.com CBUS-EP00

29