Paradox DGP-620, DGP-648 Programming Manual

20-Zone, and 48-Zone LED Keypads V1.3

(DGP-620/648)

Programming Guide

Bold = Default Setting

SECTION [003]: General Options

Option OFF ON

[1] Muting l Disabled l
[2] Exit Delay Beep l Disabled l
[3] Not used l N/A l N/A
[4] Chime on Zone Closure l Disabled l
[5] Not used l N/A l N/A
[6] Not used l N/A l N/A
[7] Not used l N/A l N/A
[8] Not used l N/A l N/A

Enabled

Enabled

Enabled

MODULE PROGRAMMING MODE

The keypad, like all other modules in the Digiplex system, is
programmed through the control panel. To enter the Module
Programming Mode:

Step 1: Press and hold the [0] key.
Step 2: Enter the [INSTALLER CODE] (by default 000000).
Step 3: Enter section [953].
Step 4: Enter the keypad’s 8-digit [SERIAL NUMBER].
Step 5: Enter the 3-digit [SECTION] to program.
Step 6: Enter the required [DATA].

PROGRAMMING GUIDE

Serial Number: ___/___/___/___/___/___/___/___
Location:______________________________________________

Bold = Default Settings

SECTION [001]: Partitioning

Option OFF ON

[1] Partition 1 l Disabled l
[2] Partition 2 l Disabled l
[3] Partition 3 l Disabled l
[4] Partition 4 l Disabled l
[5] Not used l N/A l N/A
[6] Not used l N/A l N/A
[7] Not used l N/A l N/A
[8] Not used l N/A l N/A

Enabled
Enabled
Enabled
Enabled

SECTION [004]: Beep on Trouble

Option OFF ON

[1] System & Clock Loss l Disabled l
[2] Communicator l Disabled l
[3] Modules & Bus l Disabled l
[4] All Zones Troubles l Disabled l
[5] Not used l N/A l N/A
[6] Not used l N/A l N/A
[7] Not used l N/A l N/A
[8] Not used l N/A l N/A

SECTION [005]: General Options

Option OFF ON

[1] PGM State l Normal

Open

[2] PGM Timed Mode l Disabled l
[3] PGM Base Time l 1 Second l
[4] PGM Override l Disabled l
[5] Keypad Tamper l Disabled l
[6] Not used l N/A l N/A
[7] Not used l N/A l N/A
[8] Not used l N/A l N/A

Section:
[006] ___/___/___
PGM Timer 000 to 255 (refer to the Digiplex LED Keypad Installer
Manual).

l

Enabled
Enabled
Enabled
Enabled

Normally
Closed

Enabled
1 Minute
Enabled
Enabled

SECTION [002]: General Options

Option OFF ON

[1] Not used l N/A l N/A
[2] Not used l N/A l N/A
[3] Not used l N/A l N/A
[4] Confidential Mode l Disabled l
[5] To Normal Mode

(if [4] is enabled)

[6] Not used l N/A l N/A
[7] Not used l N/A l N/A
[8] Not used l N/A l N/A

l Enter

Code

Enabled

l Press

Button

[007] ___/___ ( 1 2 3 4 5 6 7 8 )
PGM Activation Event
For the PGM Table refer to the Digiplex Programming Guide.

[008] ___/___ ( 1 2 3 4 5 6 7 8 )
PGM Deactivation Event
For the PGM Table refer to the Digiplex Programming Guide.

[009] Zone Display (DGP-620 only)
20 - Zone Keypad: l [0] = 1 to 20 l [1] = 21 to 40

Figure 1 - Connecting Keypads & Keypad Zones

Figure 2 - Basic Keypad Overview