NEW! Redesigned Remote Control with 2 ‘AAA’ batteries
NEW! Upgraded Control Box with Digital Signal Processing engine that provides …
NEW! Dolby Digital
NEW! Bluetooth with aptX coding
NEW! Music Mode (For use with 2-channel content)
NEW! Movie Mode featuring Paradigm Virtual Surround (For use with
Dolby Digital-enabled content
NEW! IR Learning
About the Remote Control
About the Control Box
On / Off
Toggle left through sources
Toggle right through sources
Play / Pause
*Sonic enhancements to listening experience according to mode
Greyed out buttons do not apply to this model
On / Off
About ParadigmVirtual Surround?
Typically in a 2.1 system, all the audio magic of Dolby Digital or DTS Digital surround information is lost, since there are no surround speakers to deliver it. This precious information sits in the front left and right speaker channels wondering what to do with itself.
Using sophisticated mathematical algorithms, Paradigm Virtual Surround processing gathers that neglected surround information in a central sweet spot then reflows it into the front left and right channels. It’s then sent out into the room in a way that creates the auditory illusion of sound enveloping the listeners on all sides. An‘illusion’ perhaps, but to our ears, designed to hear in three dimensions, this spacious, ambient sound that swirls around us is very real.
Enabling IR Learning on Millenia CT 2
1.To enable IR Learning on Millenia CT 2, press and hold the‘MUTE’button for 5 seconds on either the remote control or the control box. The LED on the front of the control box will glow a brighter‘BLUE’. This indicates Millenia CT 2 is now in IR Learning Mode.
2.Using either the remote control or the control box press the command you would like Millenia CT 2 to learn.
For example: If you want the Millenia CT 2 to learn the‘VOLUME +’ command, press ‘VOLUME +’. The LED on the front of the Control Box will flash ‘BLUE’slowly, this indicates that the Millenia CT 2 is in the process of learning a command.
3.Press the corresponding button on the 2nd remote control to learn the command.
4.The LED on the front of the Millenia CT 2’s Control Box will flash‘BLUE’ 5 times in quick succession to confirm the command was received.
5.Wait a few seconds, then again press the button on the 2nd remote control to confirm the desired command.
6.The LED on the front of the Millenia CT 2’s Control Box will again flash ‘BLUE’5 times in quick succession to confirm the command was received.
7.If the command was learned correctly, the LED on the front of the Millenia CT 2’s Control Box will now glow a brighter‘BLUE’.
Repeat steps 2 through 6 to learn additional commands. NOTE: If you wait more than 20 seconds between programming commands, the Millenia CT 2 will exit the IR Learning Mode. Then you will have to start the entire process again in order to program additional features.
To end IR Learning
If no other command is pressed, the Millenia CT 2 will automatically exit IR Learning Mode in 20 seconds.
What to do if the LED flashes‘PURPLE’
If the LED on the front of the Millenia CT 2’s Control Box flashes‘PURPLE’, the command was not received correctly. Please try again. If the LED on the
Control Box flashes‘PURPLE’after a second attempt, the Millenia CT 2 may not be able to learn your remote control.
IMPORTANT: The IR Learning Mode operates via standard 38Khz IR protocol only. Not all remotes function in the same manner. If the LED on the Control Box continues to flash‘PURPLE’it could indicate an error, please try another remote control.
How to Set Up Bluetooth
Using the Millenia CT 2’s Remote Control or Control Box …
1.Turn Millenia CT 2 on.
2.Press the Bluetooth button.
3.On your Bluetooth enabled device, search for‘Millenia CT 2’.
4.The pairing process will begin automatically and pairing will take place once a link between the device and Millenia CT 2 is established.
5.Start music playback.
RECYCLING AND REUSE GUIDELINES FOR EUROPE
In accordance with the European Union WEEE (Waste Electrical and Electronic Equipment) directive effective August 13, 2005, we would like to notify you that this product may contain regulated materials which, upon disposal, according to the WEEE directive, require special reuse and recycling processing. For this reason Paradigm Electronics Inc. (manufacturers
of Paradigm speakers and Anthem Electronics) has arranged with our distributors in European Union member nations to collect and recycle this product at no cost to you. To find your local distributor please contact the dealer from whom you purchased this product or go to our website at www.paradigm.com/shift. Please note that the product only falls under the WEEE
directive. When disposing of packing and other shipping material we encourage you to recycle through the normal channels.
FCC ID: WUO-WBT1010 and IC ID: 7985A-WBT1010. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including information that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
WIRELESS TRANSMITTER COMPLIANCE INFORMATION
The term “IC” before the radio certification number only signifies that Industry Canada technical specifications were met. This equipment complies with FCC and IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body. This transmitter must not be co-located or operating
in conjunction with any other antenna or transmitter. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that permitted for successful communication.
Manufactured under license from Dolby Laboratories. Dolby and the double-D symbol are trademarks of Dolby Laboratories.
The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by Paradigm Electronics Inc. is under license.
The “aptX® software is copyright CSR plc or its group companies. All rights reserved. The aptX® mark and the aptX logo are trade marks of CSR plc or one of its group companies and may be registered in one or more jurisdictions.”