Page 1
887 LAT OPTION
CLASS H
PART # 7305601
REV . A
USER’S GUIDE
1
WARNING:
Read and follow all directions
for each step to insure proper
assembly of this product.
Version: 887108
Revision: 06/20/02
Page 2
j
TABLE OF CONTENTS
Safety Statement.............2
General Notes..................3
Tools Required................3
Parts list..........................4
Assembly Instructions.....4-13
General Maintenance.......14
W arranty Statement..........15
Product Services..............16
Insert-Registration Card
IMPORTANT SAFETY INFORMATION
THERE IS A RISK ASSUMED BY INDIVIDUALS WHO USE THIS TYPE OF
EQUIPMENT. TO MINIMIZE RISK FOLLOW THESE RULES!
1. Before using, read all the warnings and instructions
on the use of this machine. Use only for intended
exercise. DO NOT modify the machine.
2. Obtain a medical exam before beginning any
exercise program.
3. Keep body and clothing free of all moving objects.
4. Inspect the machine before use. DO NOT use it if it
appears damaged. DO NOT attempt to fix a broken or
ammed machine. Notify your authorized ParaBody
dealer before use and have repairs made by an
authorized service technician.
6. Never pin the weights or prop plate into an elevated
position. DO NOT use the machine if found in this
condition. DO NOT attempt to fix. Notify your
authorized ParaBody dealer.
7. Inspect cables and their connections before using
machine. Pay particular attention to the cable ends.
DO NOT attempt to fix. Notify your authorized
ParaBody dealer before use and have repairs made by
an authorized service technician.
8. Make sure all spring loaded pull pins are fully
engaged in the adjustment position and fully tighten
thumbscrew before use.
5. Be certain that weight pin is completely inserted.
Use only the pin provided by the manufacturer. If
unsure, call your authorized ParaBody dealer.
9. Children must not be allowed near this machine.
Supervise teenagers.
.
NOTE: In a continual effort to improve our products, specifications are subject to change
2001 Life Fitness, a division of Brunswick Corporation. All rights reserved.
©
ParaBody is a trademark of Brunswick Corporation
www.parabody.com
2
Page 3
IMPORTANT NOTES
Please note:
* Thank you for purchasing the ParaBody 877 Lat Option. Please read these
instructions thoroughly and keep them for future reference. This product must be assembled
on a flat, level surface to assure its proper function.
* This product must be assembled on a flat, level surface to assure its proper function. DO NOT
securely tighten any frame connections until the entire frame has been assembled, unless
otherwise stated.
T ools Required for Assembly
* 3/4” wrench
* 9/16” wrench
* Ratchet with 3/4” and 9/16” sockets
* Adjustable wrench
* T ape measure
Bolt Length Ruler
NOTE: BOL T LENGTH IS MEASURED FROM THE UNDERSIDE OF THE HEAD OF THE BOLT.
BOLT LENGTH
BOL T LENGTH RULER:
1/2 1/2 1/2 1/2 1/2 1/2
0
1
2
345
3
6
Page 4
PARTS LIST
KEY
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
PART #
LEA6800209
LEA6800610
LEA6800809
LEA6801009
LEA6801110
LEA6759810
LEA6274410
LEA6725310
LEA3116201
LEA3116101
LEA6802101
LEA6671601
LEA6692601
LEA3103102
LEA6140701
LEA6405201
LEA3116001
LEA6177001
LEA3119301
DESCRIPTION
UPRIGHT
ADJ FOOT SUPPOR T
PULLEY HOUSING
TOP BOOM
LA T BAR SUPPOR T
CARRIAGE
LOW ROW BAR
LA T BAR
3-1/2” PULLEY
4-1/2” PULLEY
115-1/4” CABLE
121-3/4” CABLE
3 X 2” END CAP
1 X 8” GRIP
1 X 1” GLIDE
2” SQ. END CAP
1-1/4” SQ. RUBBER BUMPER
2-1/2 X 5-1/2” NON-SKID STRIP
2-1/2” ROUND END CAP
QTY
1
1
1
1
1
1
1
1
5
1
1
1
2
4
8
2
1
2
2
KEY
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
PART #
LEA6236701
LEA6412001
LEA3203301
LEA6542402
LEA6416601
LEA3235314
LEA3114401
LEA3114701
LEA3235316
LEA3235502
LEA3114403
LEA3114702
LEA3235211
LEA6480301
LEA3103801
LEA3235208
LEA3108102
LEA6075906
LEA3235216
DESCRIPTION
1-3/4” SQ. END CAP
SPRING PIN ASSEMBL Y
VINYL CAP
3/16 X 1-3/4 X 5-1/4” PLA TE
3/4 X 1-1/2” GLIDE
1/2 X 3-1/2” BOL T
1/2” W ASHER
1/2” LOCK NUT
1/2 X 4” BOL T
3/8” LOW HEIGHT LOCK NUT
3/8” W ASHER
3/8” LOCK NUT
3/8 X 2-3/4” BOL T
3/8” FLANGE SP ACER
5/16” SNAP HOOK
3/8 X 2” BOL T
1/4” QUICK LINK
12 LINK CHAIN
3/8 X 4” BOL T
QTY
1
1
2
2
1
1
2
1
1
3
14
9
6
8
3
2
1
1
4
7/16” CAP PLUG
7/16” CAP
PLUG
FIGURE 1
STEP 1:
• Remove four 7/16” CAP PLUGS from the UPPER & LOWER CROSS SUPPOR TS on the 888 SMITH MACHINE as shown in FIGURE 1.
4
Page 5
UPRIGHT FRAME
16
3/8 X 4” 38
30
3
LOWER CROSS SUPPORT
1
21
24
30
FIGURE 2
3/8” LOW HEIGHT LOCK NUT 29
STEP 2:
• NOTE: It may be necessary to loosen the 1/2 X 3-1/4” BOL TS of the LOWER CROSS SUPPORT connecting the UPRIGHT
FRAME before beginning STEP 2.
• Attach four 3/4 X 1-1/2” GLIDES (24) to the inside of the tube on the UPRIGHT (1) as shown in FIGURE 2 using the following steps:
• Thoroughly clean all surfaces where the 3/4 X 1-1/2” GLIDES (24) are to be attached.
• Remove the 3/4 X 1-1/2” GLIDES (24) from the paper backing and firmly apply them to all shown surfaces.
• SECUREL Y assemble one SPRING PIN ASSEMBLY (21) to the spring pin barrel on the UPRIGHT (1). See FIGURE 3.
• LOOSEL Y assemble the PULLEY HOUSING (3) and the UPRIGHT (1) to the LOWER CROSS SUPPOR T using two 3/8 X 4” BOL TS
(38), four 3/8” W ASHERS (30), and two 3/8” LOW HEIGHT LOCK NUTS (29). See FIGURE 2.
• Insert one 2” SQ. END CAP (16) into the end of the PULLEY HOUSING (3) as shown in FIGURE 2.
1/2 1/2 1/2 1/2 1/2 1/2
0
1
2
345
5
6
Page 6
1
19
20
18
24
2
FIGURE 3
STEP 3:
• Insert two 2-1/2” ROUND END CAPS (19) into the ends of the ADJ. FOOT SUPPORT (2) as shown in FIGURE 3.
• Insert one 1-3/4” END CAP (20) into the end of the ADJ. FOOT SUPPOR T (2) as shown in FIGURE 3.
• Apply two 2-1/2 X 5-1/2” NON-SKID STRIPS (18) to the ADJ. FOOT SUPPORT (2) as shown in FIGURE 3.
• Attach four 3/4 X 1-1/2” GLIDES (24) to the outside of the ADJ FOOT SUPPORT (2) and four GLIDES to the inside of the
tube on the UPRIGHT (1) as shown in FIGURE 3 using the following steps:
• Thoroughly clean all surfaces where the 3/4 X 1-1/2” GLIDES (24) are to be attached.
• Remove the 3/4 X 1-1/2” GLIDES (24) from the paper backing and firmly apply them to all shown surfaces.
• Pull back on the SPRING PIN (21) and CAREFULL Y insert the ADJ. FOOT SUPPOR T (2) into the UPRIGHT (1) as shown in FIGURE 3.
6
Page 7
6
15
17
FIGURE 4
STEP 4:
• Attach eight 1 X 1” GLIDES (15) to the ends the CARRIAGE (6) as shown in FIGURE 4 using the following steps:
• Thoroughly clean all surfaces where the 1 X 1” GLIDES (15) are to be attached.
• Remove the 1 X 1” GLIDES (15) from the paper backing and firmly apply them to all shown surfaces.
• Attach one 1-1/4” SQ. RUBBER BUMPER (17) to the underside of the angle on the CARRIAGE (6) as shown in FIGURE 4.
13
1
FIGURE 5
STEP 5:
• CAREFULL Y slide the CARRIAGE (6) over the UPRIGHT (1) as shown in FIGURE 5.
• Insert one 3 X 2” END CAP (13) into the end of the UPRIGHT (1). See FIGURE 5.
1/2 1/2 1/2 1/2 1/2 1/2
0
1
2
345
6
6
7
Page 8
FIGURE 6
1/2 X 3-1/2” 25
UPRIGHT FRAME
27
4
26
31
28 1/2 X 4”
UPPER CROSS
SUPPORT
13
30
38 3/8 X 4”
UPRIGHT
STEP 6:
• NOTE: It may be necessary to loosen the 1/2 X 3-1/4” BOL TS of the UPPER CROSS SUPPORT connecting the UPRIGHT
FRAME before beginning STEP 6.
• LOOSEL Y assemble the T OP BOOM (4) to the UPRIGHT (1) using one 1/2 X 4” BOL T (28), one 1/2 X 3-1/2” BOL T (25), two 1/2”
W ASHERS (26), and one 1/2” LOCK NUTS (27) as shown in FIGURE 6.
• LOOSEL Y assemble the T OP BOOM (4) to the UPPER CROSS SUPPOR T using two 3/8 X 4” BOLTS (38), four 3/8” W ASHERS (30)
and two 3/8” LOCK NUTS (31). See FIGURE 6.
• Insert one 3 X 2” END CAP (13) into the end of the TOP BOOM (4). See FIGURE 6.
• SECURELY tighten all connections made up to this point.
FIGURE 7
4
3/8” LOW HEIGHT 29
5
22
32 3/8 X 2-3/4
STEP 7:
• SECURELY assemble the LA T BAR SUPPOR T (5) to the TOP BOOM (4) using one 3/8 X 2-3/4” (32) and one 3/8” LOW HEIGHT LOCK
NUT (29). See FIGURE 7.
• Slide two VINYL CAPS (22) over the LAT BAR SUPPOR T (5) as shown in FIGURE 7.
8
Page 9
FIGURE 8
31
33
4
9
3/8 X 2-3/4” 32
11
STEP 8:
• Route the 115-1/4” CABLE (11) through the TOP BOOM (4) as shown in FIGURE 8.
• SECUREL Y assemble three 3-1/2” PULLEYS (9) into the slots of the TOP BOOM (4) using three 3/8 X 2-3/4” BOL TS (32), six 3/8” FLANGE
SP ACERS (33), and three 3/8” LOCK NUTS (31) as shown in FIGURE 8. (NOTE: Make sure the cable is r outed over all the pulleys.)
1/2 1/2 1/2 1/2 1/2 1/2
0
1
2
345
9
6
Page 10
FIGURE 9
4
31
9
23
11
36
30
35 3/8 X 2”
!IMPORTANT!
SECUREL Y
TIGHTEN
6
STEP 9:
• Attach the CABLE (11) from the TOP BOOM (4) to the CARRIAGE (6) using one 1/4” QUICK LINK (36) as shown in FIGURE 9.
(IMPORT ANT! Securely tighten QUICK LINK.)
• Place one 3-1/2” PULLEY (9) into the loop of the CABLE (12) below the second and third PULLEY of the TOP BOOM (4) as shown
in FIGURE 9.
• LOOSEL Y assemble two 3/16 X 1-3/4 X 5-1/4” PLA TES (23) to each side of the 3-1/2” PULLEY (9) using one 3/8 X 2” BOL T (35),
two 3/8” W ASHERS (30), and one 3/8” LOCK NUT (31). See FIGURE 9.
10
Page 11
31
10
12
33
3
33
32 3/8 X 2-3/4”
FIGURE 10
STEP 10:
• Route the threaded end of the 121-3/4” CABLE (12) through the slot of the PULLEY HOUSING then SECURELY assemble one 4-1/2”
PULLEY (10) to the PULLEY HOUSING (3) using two 3/8 X 2-3/4” BOL TS (32), two 3/8” FLANGE SP ACERS (33), two 3/8” W ASHERS
(30), and two 3/8” LOCK NUTS (31). (NOTE: The CABLE (12) should be routed between the pulley and the retaining bolt as shown in
FIGURE 10.)
11
Page 12
23
31
9
12
30
35 3/8 X ”
UPRIGHT
THREADED END
SECUREL Y
TIGHTEN
FIGURE 11
JAM NUT!
STEP 1 1:
• Loop the 121-3/4” CABLE (12) around one 3-1/2” PULLEY (9) as shown in FIGURE 11.
• LOOSEL Y assemble the 3-1/2” PULLEY (9) to the 3/16 X 1-3/4 X 5-1/4” PLA TES (23) using one 3/8 X 2” BOL T (35), two 3/8” W ASHERS
(30), and one 3/8” LOCK NUT (31). See FIGURE 11.
• SECURELY thread the end of the 121-3/4” CABLE (12) 3/4 of the way into into the threaded housing on the UPRIGHT and SE-
CURELY tighten jam nut.
• SECUREL Y tighten the two 3/8 X 2” BOL TS (35) of the 3/16 X 1-3/4 X 5-1/4” PLA TES (23).
12
Page 13
14
11
34
8
12
34
34
37
7
14
FIGURE 12
STEP 12:
• Slide two 1 X 8” GRIPS (14) on the LOW ROW BAR (7) and two 1 X 8” GRIPS (14) on the LAT BAR (8) as shown in FIGURE 12.
• Attach the LAT BAR (8) to the ball end of the upper CABLE (11) using one 5/16” SNAP HOOK (34) as shown in FIGURE 12.
• Attach the LOW ROW BAR (7) to the ball end of the lower CABLE (12) using one 12-LINK CHAIN (37) and two 5/16” SNAP HOOKS
(34) as shown in FIGURE 12.
Thank you for purchasing the Parabody 887 LA T OPTION. If unsur e of proper use of equipment, call your
local Parabody distributor or call the Parabody customer service department at (800) 328-9714.
13
Page 14
MAINTENANCE
Please note:
* We recommend cleaning your product (pads and frame) on a regular basis, using warm soapy
water . Touch-up paint can be purchased from your ParaBody customer service representative
at (800) 328-9714.
* Inspect equipment daily . Tighten all loose connections are replace worn parts immediately.
Failure to do so may result in serious injury
* Lubricate guide rods with a teflon based (or equivalent) lubricant on a regular basis
* PLEASE RECORD THE INFORMATION REQUESTED BELOW. IN THE EVENT
YOU MAY NEED SERVICE YOU WILL BE ASKED FOR THIS INFORMA TION.
REMEMBER TO FILL OUT YOUR WARRANTY REGISTRATION CARD AND
MAIL BACK.
MODEL #________________________
SERIAL #_________________________
DATE OF PURCHASE: _____________
DEALERS NAME: _________________
DEALERS PHONE #_______________
SERIAL NUMBER LOCATION
Thank you for purchasing the ParaBody 887 Lat Option.
14
Page 15
LIMITED W ARRANTY
ParaBody extends the following LIMITED WARRANTY to the original owner of the ParaBody products. The Warranty terms apply to IN HOME USE ONL Y.
1. LIMITED WARRANTY ON FRAME AND WELDS. If the frame of the ParaBody product or a weld should crack or break, it will be repaired
or replaced by ParaBody. Terms: Lifetime – for so long as the Customer owns the ParaBody product.
2. LIMITED WARRANTY ON P ARTS. If the following part s are defective in material or workmanship, ParaBody will supply replacement parts:
all bolts, nuts, washers, bearings, bushings, pulleys, thumbscrews, collars, cable retaining clips, adjustable pre-stretch slides, roller pad
shafts, allen head bolts, weight selector pin, weight stack shaft, set screws, protector caps, adjustment chain, cotter pin, plunger , spring
and knob. Terms: Lifetime – for so long as the Customer owns the ParaBody product.
3. LIMITED WARRANTY ON CABLES AND UPHOLSTERY. If the coated cables or upholstery are defective in material or workmanship,
ParaBody will repair or replace them, at its option. Terms: Three (3) years.
4. CONDITIONS AND EXCEPTIONS. Any product misuse, abuse or alteration, any attempt to repair by a person other than an authorized
ParaBody Service Center, any improper assembly, accident, or any other condition resulting from occurrences beyond the control of
ParaBody will void this Limited Warranty .
5. REPLACEMENT AND REPAIR EXPENSES. ParaBody will provide only replacement parts or repair under this warranty. The Owner is
responsible for all other costs. Such costs may include, but are not limited to: a. labor charges for service, removal, repair or reinstallation
of the ParaBody product or any component part; b. shipping, delivery , handling and administrative charges for returning parts to ParaBody;
and c. all necessary or incidental costs related to installation of the replacement parts.
6. SHIPPING . If shipping by the Owners is deemed necessary (in sole discretion of ParaBody), parts should be shipped in their original carton
or equivalent packaging, fully insured with shipping charges prepaid. ParaBody will not assume any responsibility for any loss or damage
incurred in shipping.
7. CLAIM PROCEDURES. If service on your ParaBody product is required during the warranty period, please contact our Customer Service
Department at 1-800-328-9714 for instructions regarding returning or replacing parts. Please have available the following information: (i) the
dealer’s name; (ii) the date of purchase; (iii) the serial # (s) of your product (the serial number location is called out on the final assembly
drawing included with your assembly instruction); (iv) a description of the nature of the problem.
8. OWNER’S RIGHT . This Limited W arranty gives you specific legal rights. Y ou may also have other rights, which vary depending on local law .
9. LIMITATION OF IMPLIED WARRANTIES. All implied warranties, except to the extent prohibited by applicable law , shall have no greater
duration than the warranty period set forth above. There are no warranties which extend beyond the description in this Limited Warranty .
Because local laws do not allow limitations on how long an implied warranty lasts, the above limitations may not apply to you.
10. DISCLAIMER. No other express warranty has been made or will be made on behalf of ParaBody with respect to any ParaBody product or
the operation, repair or replacement of any ParaBody product. ParaBody shall not be responsible for injury , loss of use of the ParaBody
product, inconvenience, loss or damage to personal property, whether direct or indirect, and incidental or consequential damages, so the
above limitation or exclusion may not apply to you.
NOTES:
15
Page 16
LIFE FITNESS
14150 Sunfish Lake Blvd. Ramsey Minnesota, 55303 U.S.A.
T el: 763.323.4500 Fax: 763.323.4797
800.328.9714 (T oll-free within the U.S. and Canada)
www.parabody.com
INTERNATIONAL OFFICES
Life FitnessAtlantic BV
Atlantic Headquarters
Bijdorpplein 25-31
2992 LB Barendrecht
The Netherlands
Phone: (180) 646 666
Fax: (180) 646 703
Life Fitness EUROPE GmbH
Siemensstrasse 3
85716 Unterschleissheim
Germany
Phone: (089) 31 77 51-0
Fax: (089) 31 77 51 99
Life Fitness Italia S.R.L.
V ia Elvas 92
39042 Bressanone
Italy
Phone: 39 (472) 835-470
Fax: 39 (472) 833-150
Life Fitness (UK) Ltd.
Queen Adelaide
Ely , Cambs CB7 4UB
United Kingdom
Phone CSS: (01353) 665507
Fax CSS: (01353) 666719
Life Fitness Benelux N.V.
Bijdorpplein 25-31
2992 LB Barendrecht
The Netherlands
Phone: 31 (180) 64 66 69
Fax: 31 (180) 64 66 99
Life Fitness Japan
8/F , Nippon Brunswick Building
5-27-7 Sendagaya
Shibuya-Ku, T okyo 151-0051
Japan
Phone: 81 (3) 3359-4309
Fax: 81 (3) 3359-4307
Life Fitness Asia Pacific Limited
Room 2610, Miramar T ower
132 Nathan Road, T simshatsui
Kowloon, Hong Kong
Phone: (852) 2891-6677
Fax: (852) 2575-6001
16
Life Fitness Do Brazil
Al. Rio Negro, 433-Predio 2-Sala 2
3
º andar (Confab)
Aplhaville-Barueri-Sao Paulo
CEP: 06454-904
Brazil
Phone: 55 (11)7295-2217
Fax: 55 (11) 7295-2218
Loading...