ParaBody 8661O2 User Manual

8661O2

STRENGTH BUILDING SYSTEM

THANK YOU

FOR PURCHASING THE 866102 STRENGTH BUILDING SYSTEM. PLEASE SAVE THESIE ASSEMBLY

INSTRUCTIONS FOR YOUR PERSONAL REFERENCE, AND ADDITIONAL SERVICE

LNFOR_MATION.

***!MP, ORTANT***

THE 866102 STRENGTH BUILDING SYSTEM MUST BE ASSEMBLED ON A FLA~, LEVEL
SURFACE TO ASSURE ITS PROPER FUNCTION.

PARABODY INC. STRONGLY RECOMMENDS THAT THIS PRODUCT BE ASSENI]?,LED BY TWO
PERSONS TO AVOID POSSIBLE INJURY.

IF YOU EXPERIENCE ANY PROBLEM WITH THE ASSEMBLY OF THIS PRODUCT, PLEASE
CONTACT YOUR DEALER OR YOUR PARABODY CUSTOMER SERVICE REPRESENTATIVE
AT: 1-800-328-9714

TOOL-S REQUIRED: RATCHET, 3/4 SOCKET or WRENCH, 9/16 SOCKET or WRENCH,

ADJUSTABLE WRENCH, and RUBBER MALLET or HAMMER

ASSEMBLY

INSTRUCTIONS

Part # 6611901 1

Revision: 04/30/96

SORT AND COUNT ALL PARTS BEFORE BEGINNING ASSEMBLY

HARDWARE:

ITEM

1.

2.

3.

4.

5.

6.

7.

8.

9.
lO.

11.

12.

13.

14.

15.

16.

17.

18.

19.

20.

21.

NAME/DESCRIPTION QTY

3 x 2" END CAP .................................................................................................................... 2

3/8" FLAT WASHER ............................................................................................................. 6

1/2" FLAT WASHER ............................................................................................................. 6

I/2" NYLOCK NUT ............................................................................................................... 6

3/8" NYLOCK NUT ...............................................................................................................

1/2" LOW HEIGHT NYLOCK NUT ...................................................................................... 1

3/8 X 1-1/4" BOLT ..................................................................................................................

1/2 X 3" BOLT ........................................................................................................................ 6

3/8 X 2-3/4" BOLT .................................................................................

1/2 X 3-1/2" BOLT ................................................................................................................. 1

PAL NUT ..................................

1-1/4" SQ, RUBBER BUMPER ............

I/2" FLANGE BEARING ....................................................................................................... 2

1 X 1 GLIDE ...........................................................................................................................

3 PRONG KNoB ...................................................................................................................... 2

2" SQ. END CAP .....................................................................................................................

HINGE TAB ........................................................................................................................... 4

U-PIN ...................................................................................................................................... 1

SPRING PIN ASSEMBLY ..................................................................................................... 1

I-1/2 X 3/4" GLIDE QTY8 .....................................................................................................

2" SQ. COVER CAP .................................. , .............................................................................1

: ............................... 1

~ .............................................................................................

~ .................................................................................

4

1
1

2

4

1

WELDMENTS/PARTS:
ITEM

1.

2..

3.

4.

5.

6.

7.

8.

9.
I0.

NOTE: BOLT LENGTH IS MEASURED FROM THE UNDERSIDE OF THE HEAD OF TltE BOLT.

BOLT LENGTH RULER:

NAME/DESCRIPTION QTY

WOLFF SLEEVE WLDMT ............................................

HEIGHT ADJUSTMENT BAR WLDMT ...................... (6428601) .......................................

BENCH SLIDE WLDMT ............................................... (6428701) .......................................

BACK PAD ................................ ~ ....................................(6452401) ....................................... 1

SEAT PAD ...................................................................... (6452501) ....................................... 1

CROSS BRACE WLDMT .............................................. (6606901) .......................................

UPRIGHT FRAME WLDMT ......................................... (6607501) ........................................

BENCH FRAME WLDMT .............................................

SLIDE SUPPORT WLDMT ........................................... (6611701) ........................................ 1

UPRIGHT LABELS (1-25) ............................................. (6189501) .......................................

1/2 1/2 [

112

[ 1/2 [

(6406601) ........... .’ ............................1

(6607701) ....................................... 1

1/2

’l’

1
1

1

2

2

1~2 ]

.4 5 62 3

I,,, , , I I ,J I ,

Pa~# 6611901 Revision: 04/30/96