ParaBody 848 User Manual
848 LAT OPTION
CLASS H
PART # 7080301
REV . B
USER’S GUIDE
1
WARNING:
Read and follow all directions
for each step to insure proper
assembly of this product.
Version: 848107
Revision: 07/10/01
j
TABLE OF CONTENTS
Safety Statement.............2
General Notes..................3
Tools Required................3
Parts list..........................4
Assembly Instructions.....4-15
General Maintenance.......16
W arranty Statement..........17
Product Services..............18
Insert-Registration Card
IMPORTANT SAFETY INFORMATION
THERE IS A RISK ASSUMED BY INDIVIDUALS WHO USE THIS TYPE OF
EQUIPMENT. TO MINIMIZE RISK FOLLOW THESE RULES!
1. Before using, read all the warnings and instructions
on the use of this machine. Use only for intended
exercise. DO NOT modify the machine.
2. Obtain a medical exam before beginning any
exercise program.
3. Keep body and clothing free of all moving objects.
4. Inspect the machine before use. DO NOT use it if it
appears damaged. DO NOT attempt to fix a broken or
ammed machine. Notify your authorized ParaBody
dealer before use and have repairs made by an
authorized service technician.
6. Never pin the weights or prop plate into an elevated
position. DO NOT use the machine if found in this
condition. DO NOT attempt to fix. Notify your
authorized ParaBody dealer.
7. Inspect cables and their connections before using
machine. Pay particular attention to the cable ends.
DO NOT attempt to fix. Notify your authorized
ParaBody dealer before use and have repairs made by
an authorized service technician.
8. Make sure all spring loaded pull pins are fully
engaged in the adjustment position and fully tighten
thumbscrew before use.
5. Be certain that weight pin is completely inserted.
Use only the pin provided by the manufacturer. If
unsure, call your authorized ParaBody dealer.
9. Children must not be allowed near this machine.
Supervise teenagers.
.
NOTE: In a continual effort to improve our products, specifications are subject to change
2001 Life Fitness, a division of Brunswick Corporation. All rights reserved.
©
ParaBody is a trademark of Brunswick Corporation
www.parabody.com
2
IMPORTANT NOTES
Please note:
* Thank you for purchasing the ParaBody 848 LAT OPTION. Please read these
instructions thoroughly and keep them for future reference. This product must be assembled
on a flat, level surface to assure its proper function.
* This product must be assembled on a flat, level surface to assure its proper function. DO NOT
securely tighten any frame connections until the entire frame has been assembled, unless
otherwise stated.
T ools Required for Assembly
* Rubber mallet or hammer
* 3/4” wrench
* 9/16” wrench
* Ratchet with 3/4” and 9/16” sockets
* Adjustable wrench
* T ape measure
Bolt Length Ruler
NOTE: BOL T LENGTH IS MEASURED FROM THE UNDERSIDE OF THE HEAD OF THE BOLT.
BOLT LENGTH
BOL T LENGTH RULER:
1/2 1/2 1/2 1/2 1/2 1/2
0
1
2
345
3
6
PARTS LIST
KEY
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
PART #
6826608
6826908
6825408
6827208
6825502
6275302
6274402
6542402
6824801
3103102
3116201
6177001
6405201
6467001
6692601
6825101
DESCRIPTION
BASE
UPRIGHT
ST AND
CROSS BRACE
CARRIAGE
LA T BAR
LOW ROW BAR
3/16 X 1-3/4 X 5-1/4” PLATE
CABLE
1 X 8” GRIP
3-1/2” PULLEY
2-1/2 X 5-1/2” NON-SKID STRIP
2” SQ. END CAP
2” SQ COVER CAP
3 X 2” END CAP
17-1/2” FOAM STRIP
QTY
1
1
1
1
1
1
1
2
2
4
6
2
4
2
3
1
KEY
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
PART #
3116001
6140701
3102501
3102802
3102502
3102801
3102933
3102903
3102922
3102935
3102910
3103801
3108102
6122703
6480301
6122701
DESCRIPTION
1-1/4” RUBBER BUMPER
1 X 1” GLIDE
3/8” WASHER
3/8” LOCK NUT
1/2” WASHER
1/2” LOCK NUT
3/8 X 2” BOLT
3/8 X 2-1/2” BOLT
3/8 X 2-3/4” BOLT
3/8 X 4-1/2” BOLT
1/2 X 3” BOLT
5/16” SNAP LINK
1/4” QUICK DISCONNECT LINK
3/8 X 3/8” SPACER
3/8” FLANGE SP ACER
3/8 X 1” SPACER
QTY
1
8
12
11
2
1
2
2
6
1
1
2
1
2
6
1
1/2 1/2 1/2 1/2 1/2 1/2
0
1
2
345
4
6
20
3/8 X 2-3/4” 25
14
3
13
19
FIGURE 1
STEP 1:
• Assemble two 2” SQ. COVER CAPS (14) onto the ends of the ST AND (3) as shown in FIGURE 1.
• SECURELY assemble the one 3/8 X 2-3/4” BOLT (25), two 3/8” WASHERS (19), and one 3/8” LOCK NUT (20) to the ST AND (3) as
shown in FIGURE 1.
• Assemble one 2” SQ. END CAP (13) into the end of the ST AND (3) as shown in FIGURE 1.
15
1
FIGURE 2
STEP 2:
• Insert two 3 X 2” END CAP (15) into the ends of the BASE (1) as shown in FIGURE 2.
5
13
4
16
12
FIGURE 3
STEP 3:
• Insert two 2” SQ. END CAPS (13) into the ends of the CROSS BRACE (4) as shown in FIGURE 3.
• Assemble two 2-1/2 X 5-1/2” NON-SKID STRIPS (12) to the CROSS BRACE (4) as shown in FIGURE 3.
• Assemble one 17-1/2” FOAM STRIP (16) to the underside of the CROSS BRACE (4) as shown in FIGURE 3.
5
18
17
FIGURE 4
STEP 4:
• Attach eight 1 X 1” GLIDES (18) to the ends the CARRIAGE (5) as shown in FIGURE 4 using the following steps:
• Thoroughly clean all surfaces where the 1 X 1” GLIDES (18) are to be attached.
• Remove the 1 X 1” GLIDES (18) from the paper backing and firmly apply them to all shown surfaces.
• SECURELY attach one 1-1/4” SQ. RUBBER BUMPER (17) to the CARRIAGE (5) as shown in FIGURE 4.
1/2 1/2 1/2 1/2 1/2 1/2
0
1
2
345
6
6
Loading...