Page 1
I
Serious
805106 FLAT & INCLINE BENCH
ASSEMBLY INSTRUCTIONS
Part # 6706601
1
Re~’ision: 09111/97
Page 2
IIMPO~~ANT ~OTESl
WELCOME TO THE WORLD OF g,,iou, S’,eee:
Please note:
* Thank you for purchasing the Parabody 805106 FLAT & INCLINE BENCH. Please rea~
these instructions thoroughly and keep them for future, reference. This product must be
assembled on a flat, level surface to assure its proper function.
* We recommend cleaning your product (pads and frame) on a regular basis, using warm soapy
water. Touch-up paint can be purchased from your Parabody customer service representative
at (800) 328-9714.
There is a risk assumed by individuals who use this type of equipment. To minimize risk, please
follow these rules:
Inspect equipment daily. Tighten all loose connections and replace worn parts immediately.
1.
Failure to do so may result in serious injury.
2. Do not allow minors or children to play on or around this equipment.
Exercise with. care to avoid injury.
3.
4. If unsure of proper use of equipment, call your local Parabody distributor or call the
Parabody customer service department at (800) 328-9714.
Tools Required for Assembly [
* 3/4" wrench
* 9/16" wrench
*
Ratchet with 3/4" and 9/16" sockets
* Adjustable wrench
* Tape measure
Bolt Length Ruler
NOTE: BOLT LENGTH IS MEASURED FROM THE UNDERSIDE OF THE HEAD OF THE BOLT.
,11iiiii!1
BOLT LENGTH RULER:
0 1
I I I I I
I ! I !
I
BOLT LENGTH
3 4 [ I I I
, ! I I I !
Page 3
I !
1/2 X3"
FIGURE 3
3/8
STEP 3:
¯ Snap two 3 X 2" GUIDE INSERTS (15) into the ends ofthe WOLFF SLEEVE (7) =~s-shown in HGURE
¯
In~er~ 3/8" SPRING PIN ASSEMBLY (11) into the spring pin barrel on WOLFF SLEEVE (7) and tighten
securely. See FIGURE 3.
¯
Slide one 4" VINYL CAP (17) over the U-PIN (16) as shown in FIGURE
¯
Slide U-PIN (16) through the bushing on WOLFF SLI~.Wv-E (7) and attach with PAL-NUT
¯
Slide the WOLFF SLEEVE (7) over the BENCH FRAME (3).
¯
Securely assemble the BENCH FRAME (3) to the REAR LEG (1) & the SWIVEL PLATE (2) using two
3" BOLTS (21), two 1/2" FLAT WAS~ (24), and two 1/2" NYLOCK NUTS (26) as shown in FIGURE
¯ Securely assemble the 2 SQ.X 18" TUBE (8) to the BENCHFRAME (3) using two 3/8 X3" BOLTS (19),
3/8" FLAT WASI-~I~S (23), and two 3/8" NYLOCK NUTS (25). See FIGURE 3.
0 I ! I I
I ! I ! ! ! I ! I
1 [ ! ! !
3 [ I I I
!
4
Page 4
PARTS LIST
KEY
1
2
3
4
5
6
7
8
9
10
11
12
13
PART #
6706303
6706203
6705703
6681902
6624202
6624302
6623702
6236503 2 SQ. X18"TUBE
6706002
6705802
6412001
6692601
6406401
3/8" SPRING PIN ASSEMBLY
DESCRIPTION
REAR LEG
SWIVEL PLATE
BENCH FRAM~
1/4 X 2 X 16-1/2" PLATE
LEFT BACK PAD ANGLE
RIGHT BACK PAD ANGLE
WOLFF SLEEVE
BACKPAD
SEAT PAD
3 X2" END CAP
HINGE TAB
STEP 1:
¯
Insert one 3 X 2" END CAP (12) into top of the
REAR LEG (1) as shown in FIGURE
QTY KEY
1
1
1
2
1
1 19
1
1
1
1
1
1
2
14
15
16
17
18
20
21
22
23
24
25
26
27
PART #
6467001
6590801 3 X 2" GUIDE INSERT
6619301.
3118401 4" VINYL CAP
3102909
3102904 3/8 X 3¯ BOLT
3202101
3102910
3202107
3102501
3102502
3102802
3102801
3109602
"PARABODY" LOGO END CAP
DESCRIPTION
U-PIN
3/8 X 1¯ BOLT
1/2 X 1-1/4" BOLT
1/2 X 3¯ BOLT
1/2 X 6-1/2" BOLT
3/8¯ FLAT WASHER
1/2" FLAT WASHER
3/8" NYLOCK NUT
1/2" NYLOCK NUT
PAL NUT
QTY
-4
2
1
1
6
2
2
2
1
10
4
2
5
1
¯
Slide two "PARABODY" LOGO END CAPS (14)
over the ends of the REAR LEG (1). See FIGURE
STEP 2:
¯
Slide two "PARABODY" LOGO END CAPS (14)
over the ends of the 2 SQ. X 18" TUBE (8). See
FIGURE 2.
FIGU~ 1C~"
FIGURE
Page 5
,N/I-I X rdI ~..
,N/T-I X ~/I
¢ X’IflDIzl
Page 6
* All connections use one 3/8 X 1" BOLT (18) and one 3/8" FLAT WASHER (23)
FIGURE 6
STEP 6:
¯
Securely fasten the BACK PAD (9) to the LEFT (5) and RIGHT (6) BACK PAD ANGLES using four 3/8
BOLTS (18) and four 3/8" FLAT WASHERS (23) as shown in FIGURE
¯
Securely fasten the SEAT PAD (10) to the HINGE TABS (13) using two 3/8 1"BOLTS (18) and two 3/8"
FLAT WASHERS (23) as shown in FIGURE
¯
Securely tighten the four connections on the 1/4 X 2 X 16-1/2" PLATES (4), then back nuts off 1/4 of a turn
until the BACK PAD (9) adjusts easily.
THIS CONCLUDES ~ ASSEMBLY OF THE 805106 FLAT & INCLINE BENCH
,, I,,,I,,,l,,,I,,,
¯ "
Loading...