ParaBody 435104 User Manual
435104 LEG PRESS ADAPTER KIT
ASSEMBLY INSTRUCTIONS
Part # 6865101 Revision: 2/15/001
IMPORTANT NOTES
WELCOME TO THE WORLD OF Serious steel!
Please note:
* Thank you for purchasing the 435104 Leg Press Adapter Kit. Please read these
instructions thoroughly and keep them for future reference. This product must be assembled
on a flat, level surface to assure its proper function.
* We recommend cleaning your product (pads and frame) on a regular basis, using warm soapy
water. Touch-up paint can be purchased from your Parabody customer service representative
at (800) 328-9714.
There is a risk assumed by individuals who use this type of equipment. To minimize risk, please
follow these rules:
1. Inspect equipment daily . Tighten all loose connections and replace worn parts immediately.
Failure to do so may result in serious injury.
2. Do not allow minors or children to play on or around this equipment.
3. Exercise with care to avoid injury .
4. If unsure of proper use of equipment, call your local Parabody distributor or call the
Parabody customer service department at (800) 328-9714.
T ools Required for Assembly
* Rubber mallet or hammer
* 3/4” wrench
* 9/16” wrench
* Ratchet with 3/4” and 9/16” sockets
* 7/32” Allen wrench
* Adjustable wrench
* T ape measure
Bolt Length Ruler
NOTE: BOL T LENGTH IS MEASURED FROM THE UNDERSIDE OF THE HEAD OF THE BOLT.
BOL T LENGTH RULER:
1/2 1/2 1/2 1/2 1/2 1/2
0
1
BOLT LENGTH
2
345
2
6
PARTS LIST
KEY
PART #
6747603
1
3116202
2
3108102
3
6427101
4
3118701
5
3201501
6
6271801
7
6747901
8
NOTE: The LEG PRESS A TT ACHTMENT (832101) must be assembled befor e connecting it to the
3/8” X 1” BUTTON
HEAD CAP SCREW
DESCRIPTION
FRONT LEG
3-1/2” PULLEY
QUICK DISCONNECT LINK
KEYHOLE CLEVIS
2” PULLEY
SWIVEL SNAP
72”ELASTIC CORD
LEG PRESS CABLE
P ARABODY 425104 HOME GYM
QTY
1
2
1
1
1
1
1
1
KEY
9
10
11
12
13
14
15
16
PART #
3102701
3102501
3102802
3102502
3102801
3102902
3102910
3102909
DESCRIPTION
3/8” HEX NUT
3/8” W ASHER
3/8” LOCKNUT
1/2” W ASHER
1/2” LOCKNUT
3/8 X 2-1/4” BOL T
1/2 X 3” BOL T
3/8 X 1”
QTY
2
3
2
4
4
2
4
1
REAR SHROUD
3/8” X 1” BUTTON
HEAD CAP SCREW
FIGURE 1
STEP 1
• REMOVE the four 3/8” X 1” BUTTON HEAD CAP SCREWS from the rear SHROUD. Remove the SHROUD from the 425104 HOME
GYM. See FIGURE 1.
3
REAR
SHROUD
FIGURE 2
STEP 2
• If the 445104 SECOND ST ACK OPTION is not installed, the rear SHROUD opening must be removed. Apply pressure to the bottom
of the SHROUD where the “V” groove is and carefuly remove the weight stack opening on the SHROUD as shown in FIGURE 2.
1/2 1/2 1/2 1/2 1/2 1/2
0
1
2
345
4
6
Loading...