ParaBody 435103 User Manual

I

Serious Steel

435103 LEG PRESS ADAPTER. KIT

ASSEMBLY INSTRUCTIONS

Part # 6747801 1

I

Revision: 09/25/97

]IMPORTANT NOTES]

WELCOME TO THE WORLD OF $~eiOU$ $~l~i!t

Please note:

* Thank you for purchasing the 435103 Leg Press Adapter Kit. Please read these

instructions thoroughly and keep them for future reference. This product must be assembled
on a flat, level surface to assure its proper function.

* We recommend cleaning your product (pads and frame) on a regular basis, using warm soapy

water. Touch-up paint can be purchased from your Parabody customer service representative

at [phone].

There is a risk assumed by individuals who use this type of equipment. To minimize risk, please
follow these roles:

Inspect equipment daily. Tighten all loose connections and replace worn parts immediately.

1.
Failure to do so may result in serious injury.

2. Do not allow minors or children to play on or around this equipment.

3. Exercise with care to avoid injury.

4. If unsure of proper use of equipment, call your local Parabody distributor or call the
Parabody customer service department at [phone].

I Tools Required for Assembly i

* Rubber mallet or hammer
* 3/4" wrench

*

9/16" wrench

* Ratchet with 3/4" and 9/16" sockets
* 7/32" Allen wrench

* Adjustable wrench
* Tape measure

Bolt Length Ruler I "

NOTE: BOLT LENGTH IS MEASURED FROM THE UNDERSIDE OF Tl=l-E H~EAD OF THE BOLT.

BOLT LENGTH RULER:

[ 112 [

0

I

1

1/2

BOLT LENGTH

~

1/2

2

1/2 I 1/2 I 1/2

I

4

I ’ ’

6

PARTS LIST

KEY

PART# DESCRIPTION

1

6747603 FRONT LEG

2

3116202 3-1/2" PULLEY

3

3108102 QUICK DISCONNECT LINK

4

6427101 KEYHOLE CLEVIS

5

3117305

6

3112901

7

6732901 TENSION CORD

8

6747901

NOTE: The LEG PRESS ATTAClqTMENT (832101) must be assembled before connecthlg it to the

3/8" X 1"

HEAD CAP SCREW

CLEVIS PIN

COTTER PIN

LEGPRESS CABLE

QTY KEY PART#

1

2 10 3102501

1 11 3102802
1

1 13 3102801
1

1 15 3102910

1

PARABODY 425103 t~OME GYM

9 6535301

12 3102502

14 3102933

DESCRIP’.rlON QTY

1/4" CAP NUT 1
3/8" W, HER

3/8" LOCKNUT

1/2" W, HER 4

1/2" LOCKNUT

3/8X2 BOLT
1/2X3 BOLT

4

2 .

4
2
4

3/8" X 1" BUTTON

HEAD CAP SCREW

FIGURE 1

STEP 1

¯

REMOVE the four 3/8" X 1" BUTTON HEAD CAP SCREWS from the rear SHROUD. Remove the SHROUD from the 425103

HOME GYM. See FIGURE 1.

3

FIGURE 2

STEP 2

¯

If the 445103 SECOND STACK OPTION is not installed, the rear SHROUD opening must be removed. AI?ply pressure to the

bottom of the SHROUD where the "V" groove is and carefuly remove the weight stack opening on the SHROUD as shown in
FIGURE 3.

1/2 [ 1/2 [ 1/2 I 1/2 [ 1/2

6