ParaBody 360101 User Manual
360101 375 LEG PRESS ADAPTER KIT
ASSEMBLY INSTRUCTION
Part # 6837701 Revision: 07/06/991
IMPORTANT NOTES
There is a risk assumed by individuals who use this type of equipment. To minimize risk, please
follow these rules:
1. Consult your physician before beginning any exercise program.
2. Inspect equipment daily. Tighten all loose connections and replace worn parts immediately.
Failure to do so may result in serious injury.
3. Do not allow minors or children to play on or around this equipment.
4. Exercise with care to avoid injury.
5. If unsure of proper use of equipment, call your local Parabody distributor or call the
Parabody customer service department at (800) 328-9714.
Please note:
* Thank you for purchasing the Parabody 360101 Leg Press Adapter Kit. Please read these
instructions thoroughly and keep them for future reference. This product must be assembled
on a flat, level surface to assure its proper function.
* We recommend cleaning your product (pads and frame) on a regular basis, using warm soapy
water. Touch-up paint can be purchased from your Parabody customer service representative
at (800) 328-9714.
Tools Required for Assembly
* Rubber mallet or hammer
* 3/4” wrench
* 9/16” wrench
* Ratchet with 3/4” and 9/16” sockets
* Adjustable wrench
* Tape measure
Bolt Length Ruler
NOTE: BOLT LENGTH IS MEASURED FROM THE UNDERSIDE OF THE HEAD OF THE BOLT.
BOLT LENGTH
BOLT LENGTH RULER:
1/2 1/2 1/2 1/2 1/2 1/2
0
1
2
345
2
6
PARTS LIST
KEY
STEP 1
• Slide two 2” SQ. COVER CAPS (6) over the FRONT LEG
PART #
6838003
1
6693902
2
6838103
3
3116201
4
6405201
5
6467001
6
6832701
7
3102501
8
(1) as shown in FIGURE 1.
2” SQ. RUBBER BUMPER
NOTE: The LEG PRESS A TT ACHMENT (832101) must be assembled befor e connecting it to the
DESCRIPTION
FRONT LEG
PULLEY BRACKET
BASE CONNECTION
3-1/2” PULLEY
2” SQ. END CAP
2” SQ. COVER CAP
3/8” W ASHER
P ARABODY 375 HOME GYM
QTY
1
1
1
2
1
2
1
6
KEY
6
PART #
3102802
9
3102933
10
3102910
11
3102937
12
6837801
13
6837901
14
3102502
15
3102801
16
1
DESCRIPTION
3/8” LOCKNUT
3/8 X 2” BOL T
1/2 X 3” BOL T
1/2 X 4-1/2” BOL T
PRIMARY CABLE
LEG PRESS CABLE
1/2” W ASHER
1/2” LOCK NUT
QTY
3
3
2
2
1
1
2
2
FIGURE 1
STEP 2
• Slide one 2” SQ. END CAP (5) into the BASE CONNECTION (3) as
3
5
STEP 3
• Attach one 2” SQ. RUBBER BUMPER (7) to the top of the PULLEY
BRACKET (2) as shown in FIGURE 3.
FIGURE 2
shown in FIGURE 2.
7
2
FIGURE 3
3
ST ACK GUARD
BASE
1/2”
NUT
1/2” W ASHER
FIGURE 4
STEP 4
• Remove two 1/2 X 4” BOL TS, two 1/2” WASHERS, and two 1/2” LOCK NUTS from the BASE and STACK GUARD as shown in
FIGURE 4. (NOTE: Discard the 1/2 X 4” BOL T .)
1/2 X 4” BOL T
BASE
1
1/2”
NUT
3
ST ACK GUARD
FIGURE 5
STEP 5
• Securely fasten the FRONT LEG (1) and the BASE CONNECTION (3) to the BASE and ST ACK GUARD using two 1/2 X 4-1/2”
BOL TS (12) and two previously removed 1/2” LOCKNUTS. See FIGURE 5.
1/2 1/2 1/2 1/2 1/2 1/2
0
1
2
345
4
12 1/2 X 4-1/2”
6
Loading...