PANJIT P600B, P600J, P600K, P600M, P600D Datasheet
...
P600A THRU P600M
FEATURE
S
MECHANICAL DATA
MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTIC
S
P600AP600BP600DP600GP600JP600KP600M
50100
¡C
m
P
P60
0
HIGH CURRENT PLA STIC SILICON RECTIFIER
VOLTAGE - 50 to 1000 Volts CURRENT - 6.0 Amperes
l
High surge current capability
l
Plastic package has Underwriters Laboratory
Flammability Classification 94V-O Utilizing
Flame Retardant Epoxy Molding Compound
l
Void-free plastic in a P600 package
l
High current operation 6.0 Amperes @ TA=55
l
Exceeds environmental standards of MIL-S-19500/228
Case: Molded plastic, P600
Terminals: axial leads, solderable per MIL-STD-202,
Method 208
Polarity: Color band denotes cathode
Mounting Position: Any
Weight: 0.07 ounce, 2.1 gram
¢J
*@ TA=25 ¢J unless otherwise specified. Single phase, half-wave,60 Hz, resistive or inductive load.
**All values except Maximum RMS Voltage are registered JEDEC parameters.
UNITS
Maximum Recurrent Peak Reverse Voltage
200 400 600 800 1000 V
Maximum RMS Voltage 35 70 140 280 420 560 700 V
Maximum DC Blocking Voltage 50 100 200 400 600 800 1000 V
Maximum Average Forward Rectified
Current TA=55
¢J
6.0
Maximum Overload Surge Current at 1 cycle (NOTE 1) 400 A
Maximum Forward Voltage at 6.0 ADC 1.0 V
Maximum DC Reverse Current @TA=25
Rated DC Blocking Voltage @TA=100 ¢J 1.0
¢J 10 £g
ADC
Typical Junction capacitance (Note 3) CJ 150
Typical Thermal Resistance (Note 2) R£KJA
Typical Thermal Resistance (Note 2) R£KJL
20.0
4.0
¢J
¢J
Operating Temperature Range -55 to +150 ¢J
Storage Temperature Range -55 to +150 ¢J
NOTES:
1. Peak forward surge current, per 8.3ms single half-sine-wave superimposed on rated load(JECED method)
2. Thermal resistance from junction to ambient and from junction to lead at 0.375"(9.5mm) lead length P.C.B.
mounted with 1.1×1.1”(30×30mm) copper pads
3. Measured at 1 MHZ and applied reverse voltage of 4.0 volts
A
A
A
F
/W
/W
RATING AND CHARACTERISTIC CURVES
AMBIENT TEMPERATURE (TA) - ¢J
PERCENT OF RATED PEAK REVERSE VOLTAGE
0.1
t, PULSE DURATION, sec
.
PULSE WIDTH = 300uS
INSTANTANEOUS FORWARD VOLTAGE, VOLT
S
NO. OF CYCLES AT 60H
z
IN
R
P600A THRU P600M
100
10
1
¢J
25
STANTANEOUS REVERSE CURRENT, £gA
0.1
0
20 40
60 80
100 120 140
Fig. 1-TYPICAL REVERSE CHARACTERISTICS
8.0
6.0
4.0
2.0
(Io)-AMP (Io)-AAV
AVERAGE FORWARD CURRENT
0
50 75 100
0.5" LOAD LENGTH
125
150
Fig. 2-FORWARD DERATING CURVE
100
175
200
100
10
1
0.01 0.1 1 10 100
ANSIENT THERMAL IMPEDANCE, ¢J/W
Fig. 3-TYPICAL TRANSIENT THERMAL IMPEDANCE
400
320
240
160
¢J
80
(HALF SINE-WAVE)
0
1 2 6 10
FORWARD SURGE CURRENT, Apk
TA = 60
20 40 60 100
10
1
MICROAMPERES
0.1
TJ = 25 ¢J
INSTANTANEOUS FORWARD CURRENT,
1% DUTY CYCLE
0.01
0.6 0.8 1.0 1.2 1.4 1.6 1.8
Fig. 4-TYPICAL INSTANTANEOUS FORWARD
CHARACTERISTICS
Fig. 5-MAXIMUM OVERLOAD SURGE CURRENT
Loading...