PANJIT ER3E, ER3J, ER3G, ER3D, ER3C Datasheet

DATA SHEET

ER3A~ER3J

SURFACE MOUNT RECTIFIER
VOLTAGE- 50 to 600 Volts CURRENT - 3.0 Amperes

FEA TURES

SMC / DO-214AB

Unit: inch ( mm )

• For surface mounted applications

• High temperature metallurgically bonded-no compression
contacts as found in other diode-constructed rectifiers

• Glass passivated junction

.128 (3.25)

.108 (2.75)

.245 (6.22)

.220 (5.59)

• Built-in strain relief

• Easy pick and place

• Plastic package has Underwriters Laboratory Flammability
Classification 94V-O

• Complete device submersible temperature of 260°C for 10
seconds in solder bath

MECHANICAL DATA

.103 (2.62)

.079 (2.00)

.280 (7.11)
.260 (6.60)

.012 (.305)
.006 (.152)

Case: JEDEC DO-214AB molded plastic
Terminals: Solder plated, solderable per MIL-STD-750,

Method 2026
Polarity: Indicated by cathode band
Standard packaging: 12mm tape (EIA-481)

.050 (1.27)

.030 (0.76)

.320 (8.13)
.305 (7.75)

.008(.203)
.002(.051)

Weight: 0.007 ounce, 0.21 gram

MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS

Ratings at 25°C ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, resistive or inductive load.
For capacitive load, derate current by 20%.

Maximum Recurrent Peak Reverse Voltage
Maximum RMS Voltage
Maximum DC Blocking Voltage
Maximum Average Forward Rectified Current

at T

=75°C

L

Peak Forward Surge Current 8.3ms single half sine-wave
superimposed on rated load (JEDEC method)

Maximum Instantaneous Forward Voltage at 3.0A
Maximum DC Reverse Current T
at Rated DC Blocking Voltage T
Maximum Reverse Recovery (Note 1)
Typical Junction Capacitance (Note 2)
Maximum Thermal Resistance(Note 3) RθJA
Operating and Storage Temperature Range T

NOTES:1. Reverse Recovery Test Conditions: IF=0.5A, IR=1.0A, Irr=0.25A

2. Measured at 1 MHz and applied V

3. 8.0 mm

2

( .013mm thick ) land areas.

=25°C

A

=125°C

A

J

= 4.0 volts.

r

ER3A

50
35
50

ER3B

100

70

100

0.95

ER3C

150
105
150

ER3D

200
140
200

3.0

100.0

5.0

200

35.0

45.0
16

-55 to +150

ER3E

ER3G
300
210
300

400
280
400

1.25 1.70

ER3J

UNITS

600
420
600

V

V
V

A

A

V

µA

µA

ns
pf

°C/W

°C

DATE : SEP.25.2002

PAGE . 1

10 NoninductiveW50 NoninductiveW

(+)

25 Vdc
(approx)

(-)

1

W

Noninductive

Notes:

Rise Time=7ns max.

1.
Input Impedance= 1 megohm 22pF

Rise Time=10ns max.

2.
Source Impedance= 50 Ohms 22pF

OSCILLOSCOPE
*Note1

SET TIME BAS FOR 10ns/cm

(-)

PULSE
GENERATOR
*Note2

(+)

+0.5A

0

-0.25

-1.0

t

rr

REVERSE RECOVERY TIME CHARACTERISTIC AND TEST DIAGRAM

O

100

10

1.0

TJ=100 C

TJ=75 C

O

TJ=25 C

O

1cm

4.0

3.0

2.0

1.0

AVERAGE FORWARD CURRENT, AMPERS

LEAD TEMPERATURE, C

FORWARD CURRENT DERATING CURVE

100

50-200V

10

300-400V

1.0

SINGLE PHASE HALF WAVE 60Hz
RESISTIVE OR INDUCTIVE LOAD
P.C.B. MOUNTED ON 8.0x8.0mm
COPPER LAND AREAS

250 60 70 80 90 100 110

456

O

600V

0.1

0.01

INSTANTANEOUS REVERSE CURRENT, Ampersm

2 4060806080100120140

PERCENT OF RATED PEAK INVERSE VOLTAGE, Volts

TYPICAL REVERSE CHARACTERISTICS

110

100

90

80

70

60

8.3ms SINGLE HALF SINE-WAVE
JEDC METHOD

PEAK FORWARD SURGE CURRENT, Ampers

50

1 5 10 50

100

NUMBER OF CYCLES AT 60Hz

MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT

0.1

0.01

INSTANTANEOUS FORWARD CURRENT, Ampers

0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.80

INSTANTANEOUS FORWARD VOLTAGE, Volts

TYPICAL FORWARD CHARACTERISTICS

100

90

80

F

P

70

60

50

40

CAPACITANCE,

30

20

10

0

O

TJ=25C

HZ

f

= 1.0M

V = 50 V

sig m p-p

0.1 1

10

REVERSE VOLTAGE, Volts

TYPICAL JUNCTION CAPACITANCE

O

T =25 C

J

PULSE WIDTH= 300 S
2% DUTY CYCLE

100

m

1000

DATE : SEP.25.2002

PAGE . 2