PANJIT 1F7, 1F6, 1F5, 1F3, 1F2 Datasheet

1F1 THRU 1F7

FEATURE

S

MECHANICAL DATA

MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTIC

S

1F11F21F31F41F51F61F7

P

STG

R-1

FA ST SWITCHING PLASTIC RECTIFIER

VOLTAGE - 50 to 1000 Volts CURRENT - 1.0 Ampere

l

High current capability

l

Plastic package has Underwriters Laboratory
Flammability Classification 94V-O Utilizing
Flame Retardant Epoxy Molding Compound

l 1.0 ampere operation at TA=55 ¢J with no thermal runaway

l

Fast switching for high efficiency

l

Exceeds environmental standards of MIL-S-19500/228

l

Low leakage

Case: Molded plastic, R-1
Terminals: Plated axial leads, solderable per MIL-STD-202,
Method 208
Polarity: Color band denotes cathode
Mounting Position: Any
Weight: 0.0064 ounce, 0.181 gram

Ratings at 25¢J ambient temperature unless otherwise specified.
Single phase, half wave, 60Hz, resistive or inductive load.

For capacitive load, derate current by 20%.

UNITS
Maximum Recurrent Peak Reverse Voltage 50 100 200 400 600 800 1000 V
Maximum RMS Voltage 35 70 140 280 420 560 700 V
Maximum DC Blocking Voltage 50 100 200 400 600 800 1000 V
Maximum Average Forward Rectified

Current .375"(9.5mm) lead length at TA=55 ¢J
Peak Forward Surge Current 8.3ms single half sine

wave superimposed on rated load(JECEC method)
Maximum Forward Voltage at 1.0A DC 1.3 V
Maximum Reverse Current TJ=25 ¢J

at Rated DC Blocking Voltage TJ=100 ¢J
Typical Junction capacitance (Note 1) CJ 12

Typical Thermal Resistance (Note 3) R £KJA 67 ¢J/W
Maximum Reverse Recovery Time(Note 2) 150 150 150 150 250 500 500 ns

Operating and Storage Temperature Range TJ,T
NOTES:

1. Measured at 1 MHz and applied reverse voltage of 4.0 VDC

2. Reverse Recovery T est Conditions: IF=.5A, IR=1A, Irr=.25A

3. Thermal resistance from junction to ambient and from junction to lead at 0.375"(9.5mm) lead length P.C.B.
mounted with 0.22×0.22"(5.5×5.5mm) copper pads

1.0 A

30 A

5.0

500

-55 to +150 ¢J

£g A
£g A

F

RATING AND CHARACTERISTIC CURVES

NOTE:1.Rise Time = 7ns max. Input Impedance = 1 megohm. 22pF 2.Rise Time = 10ns max. Source Impedance = 50 Ohms

r

r

SET TIME

BASE FO

R

50 ns/c

m

PULSE

INSTANTANEOUS FORWARD VOLTAGE, VOLT

S

MAXIMUM AVERAGE CURRENT RATIN

G

AMBIENT TEMPERATURE,

TJ = 25¢JREVERSE VOLTAGE, Vd

c

NUMBER OF CYCLES AT 60H

z

1F1 THRU 1F7

Fig. 1-REVERSE RECOVERY TIME CHARACTERISTIC AND TEST CIRCUIT DIAGRAM

10

1

AMPERES

0.1

INSTANTANEOUS FORWARD CURRENT,

0.01

0.2

0.4

0.6

0.8

TJ = 25

WIDTH = 300£gs
1% DUTY CYCLE

1.0 1.2 1.4

¢J

t

+0.5A

0

-0.25

-1.0

1cm

1.6

1.4

1.2

1.0
.8

.6
.4

.2

CURRENT AMPERES

0

0

20

40

AVERAGE FORWARD RECTIFIED

60

SINGLE PHASE, HALF WAVE 60Hz
RESISTIVE OR INDUCTIVE
LOAD .375"(9.5mm) LEAD LENGTHS

80 120

¢J

140

160 180

Fig. 2-TYPICAL INSTANTANEOUS

Fig. 3-FORWARD CURRENT DERATING CURVE

FORWARD CHARACTERISTICS

100

10

CAPACITANCE, pF

1

1 4 10

30

24

18

12

6

FORWARD SURGE CURRENT,

1 2 4 6 8 10

AMPERES pk (HALF-SINE WAVE)

40

60 80 100

20

Fig. 4-TYPICAL JUNCTION CAPACITANCE Fig. 5-PEAK FORWARD SURGE CURRENT