Panasonic of North America 9TAK SRB20 User Manual

Panasonic of North America 9TAK SRB20 User Manual

Confidential

DECT Microphone System

Receiver Board Module

for

Specifications

Audio Enhancement

Approval

Panasonic.

Approval

Ver. 1.0

November 29, 2019

Panasonic Corporation

Confidential

■ INDEX

 

Ver. 1.0.................................................................................................................

i

1. GENERAL ........................................................................................................

4

2. FEATURES ......................................................................................................

4

3. SPECIFICATIONS............................................................................................

4

3.1. Product Specifications ......................................................................................................

4

3.2. Accessory .........................................................................................................................

8

4. SAFETY REQUEST .........................................................................................

9

5. BLOCK DIAGRAM............................................................................................

10

6. APPEARANCE .................................................................................................

11

7. CONTROL TERMINAL SPECIFICATIONS ......................................................

13

7.1. Electrical specifications.....................................................................................................

13

8. PACKAGING SPECIFICATIONS .....................................................................

16

8.1. Packaging specifications ..................................................................................................

16

9. FCC AND INDUSTRY CANADA REQUIREMENTS REGARDING THE END

PRODUCT............................................................................................................

17

9.1. List of applicable FCC and IC rules ..................................................................................

17

9.2. FCC rules that must be complied with in the end product................................................

17

9.3. IC rules that must be complied with in the end product....................................................

17

9.4. Requirement of regarding the end product and manual...................................................

18

9.5. Notice................................................................................................................................

19

-2-

Confidential

No.

Ver.

Revision

Change

Sign

Check

Date

Time

 

 

 

 

 

 

Draft

29/Nov/

Mitsutoshi

Motoshi

1

1.0

The blue sentences is the changing points from K-SRC14

2019

Nozawa

Suzuki

 

 

(Wireless Receiver).

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

-3-

Confidential

1.GENERAL

These specifications describe the preliminary specifications of “Receiver Board Module for DECT Microp hone System” for Audio Enhancement (AE).

2.FEATURES

Receiver Board Module has same features and outside interface as DECT Receiver K-SRC14 .

System specifications and system functions including microphones are same as "DECT Microphone System"

with Receiver, so refer to “DECT Microphone System fo r Audio Enhancement Specifications”, with replace "Receiver" to "Receiver board module.

3.SPECIFICATIONS

3.1.Product Specifications

GENERAL

 

 

 

Combined AE’s product

:

BEAM, XDSolo

 

Power

:

24VDC (minimum 21.6VDC~maximum 26.4VDC)

 

 

input from AE’s product (BEAM or XDSolo)

Input current

:

130mA

 

Dimensions

:

150mm(W)x 114mm(H x 18mm(D)

Weight

:

85g

 

Temperature Range

:

0 °C ~ +50°C (around Receiver Board Module)

Humidity Range

:

~ 90%

 

The Condition of Installation

:

Indoor, Fixed Installation

Mounting direction

:

Only vertical direction with antenna facing upward

LINE Inputs

 

 

 

The number of connectors

:

1 Stereo input

(Tip:Left, Ring:Right, Sleeve:GND)

 

 

1/8" (3.5 mm) Stereo phone Jack

Internal Bus

:

Mono Mixing

 

Input Level

:

-10dBV Unbalanced

Input Impedance

:

10kΩ or more

 

OUTPUT

 

 

 

The number of connectors

:

1 Mono output

(Mix output Unbalanced)

 

 

1/8" (3.5 mm) Stereo phone Jack

Adapted Load Impedance

:

10kΩ or more

 

Nominal Output Level

:

-10dBV

 

Residual Noise

:

-60dBV or less

 

-4-

Confidential

OUTPUT (Amplifier interface)

 

 

 

 

 

Connectors

:

RJ-45 (Type for LAN), connect to Amplifier

Adapted Load Impedance

:

10kΩ or more

 

 

Nominal Output Level

:

 

 

 

 

Mic output 1,2

:

-5dBV

Balanced

 

Mix output

:

0dBV

Balanced

 

Residual Noise

:

-60dBV or less

 

GENERL SPECIFICATIONS for AUDIO

 

 

 

Cross talk

:

-45dB or more @1kHz

 

Dynamic Range

:

80dB or more

(Line In to Mix output Balanced)

 

:

80dB or more

(Line In to Mix output Unbalanced)

 

: 85dB or more (Receiver to Mic/Mix output Balanced)

 

 

By auto level control function in Microphone

Signal to noise ratio (S/N)

:

60dB or more

(Line In to Mix output Balanced)

 

:

60dB or more

(Line In to Mix output Unbalanced)

 

:

60dB or more

(Receiver to Mic/Mix output Balanced)

Frequency Response

:

100Hz ~ 7kHz,

 

 

: 0dB±3dB (Line In to Mix output)

 

 

: 0dB±3dB (Receiver to Mic output)

 

Total Harmonic Distortion

:

3.0% or less

(Line In to Mix output)

 

 

 

3.0% or less

(Receiver to Mic output)

 

Attenuator

:

Built-in each output (Mic output 1,2, Mix output)

 

 

0 dB ~ -32dB /2step

 

 

 

-32dB ~ -48dB /4step,-60dB,-70dB, OFF

 

 

(Controlled from Pendant type microphone and

 

 

RS-232C )

 

 

Mixing output attenuator

 

: -10dB attenuator build in to mixing output.

 

 

Set by dip switch

 

FEEDBACK BLOCKER

:

 

 

 

 

Assignment

:

Mic Channe1 and Mic Channel 2

 

Filter

:

5 band Filter

 

 

Operation

:

3 step operation

 

 

 

1st Step : Searching Feedback point and enable a filter

 

 

2nd Step: Add 6dB attenuation to 1st

step

 

 

3rd Step: Full attenuation

 

RESPONSE TONE

 

 

 

 

 

Number of tone signal

:

Five tone signals are build-in

 

 

 

refer to “AE DECT Mic Specification”

-2.9 TONE”

-5-

 

 

Confidential

OTHER FUNTIONS

 

 

Teacher’s over ride

:

This function will work when voice come into input from Mic CH1 or

 

 

CH2. Then Mix-output level will be set to fixed attenuate level.

 

 

Available On/Off control by Dip switch

 

 

Attenuation = 12dB or more

Paging mute

: When Paging mute terminal is activated, this function will be work.

 

 

At this time,Mic output channel 1 and 2,Mix-output level set to Mute

 

 

Level.

 

 

Attenuation = 40dB or more

Mic mixing

: Mic channel 1 and 2 are available to assign to the Mix output

 

 

This function is set by RS-232C control only

CONTROL TERMINAL

 

 

The number of connectors

: 7pin and 8pin Euro type connector

E1 output

: CONT=Maximum control voltage 30V

 

 

Maximum control current 20mA

 

 

Opt-isolated open collector

 

 

COM =common

E2 output

: CONT=Maximum control voltage 30V, Dry contact

 

 

Maximum control current 20mA

 

 

Opt-isolated open collector

 

 

COM =common

E2 acknowledgement

: IN = Pull to GND

 

 

Short current 2mA

 

 

5VDC always appear on the terminal

 

 

GND=GND

Page Mute

: IN = Pull to GND

 

 

Short current 2mA

 

 

5VDC always appear on the terminal

 

 

GND=GND

Serial port (RS-232C)

:

TxD= Transmission port

 

 

RxD=Receiver port

 

 

GND=GND

 

 

Baudrate and protocol =

 

 

9600 bps, 8 data bits,1 stop bit, No parity

 

 

Maximum distance = 15m

LINK Button

: IN = Pull to GND

 

 

Short current 2mA

 

 

5VDC always appear on the terminal

 

 

GND=GND

Alert Notification Button

: IN = Pull to GND

 

 

Short current 2mA

 

 

5VDC always appear on the terminal

 

 

GND=GND

-6-

Loading...
+ 13 hidden pages