Panasonic of North America 96NKX HNB700 User Manual
Installation Guide
HomeHawk Front Door
Model No.
KX-HN7001
HomeHawk Front Door/Outdoor
Model No.
KX-HN7002
KX-HN7003
KX-HN1007
Model shown is KX-HN7001.
Thank you for purchasing a Panasonic product.
This document explains how to configure the access point, front door camera and
optional outdoor camera using a mobile device. These steps must be followed
before you can use the system.
For details about how to use the system, refer to the User’s Guide (page
31).
Charge the batteries for about 8 hours before camera installation
(page 22).
Please read this document before using the unit and save it for future reference.
For assistance, please contact us at 1-800-272-7033 or visit our Web site:
http://shop.panasonic.com/support for customers in the U.S.A.
Please register your product: http://shop.panasonic.com/support
Printed in China
HN7001(enen)1228ver.030.pdf1 2017/12/2816:21:52
Introduction
Model composition .......................................3
Accessory information ..................................3
Expanding your camera ...............................5
Important Information
Graphical symbols for use on equipment and
their descriptions ..........................................6
About this system .........................................6
For your safety .............................................6
Important safety instructions ........................8
Security cautions ..........................................8
For best performance ...................................9
Privacy and rights of portrait ........................9
Other information .........................................9
Installation Location
Wireless communication range ..................12
Information about sensor features .............12
Information about night vision mode ..........13
Installation location examples ....................14
Do not install in these locations
..................17
Setup
Part names and functions ..........................18
Setup overview ...........................................22
Battery charging for cameras .....................22
Turning the power on for cameras .............23
Downloading the [HomeHawk] app ............23
Connections for access point .....................23
Initial setup .................................................24
Registering the camera ..............................24
Confirming the camera installation area .....25
Camera installation ....................................25
Testing the motion detection range ............29
Registering another mobile device .............29
Appendix
Features available when using the
[HomeHawk] app ........................................31
Accessing the User’s Guide .......................31
Specifications .............................................32
Open source software notice for access
point ...........................................................33
Software information for access point ........33
FCC and other information .........................34
Customer services .....................................35
Limited Warranty (ONLY FOR U.S.A.) .......36
2
Table of Contents
HN7001(enen)1228ver.030.pdf2 2017/12/2816:21:52
Model composition
Model No.
Access point Front door camera Outdoor camera
Part No. Part No. Qty. Part No. Qty.
KX-HN7001 KX-HNB700 KX-HNC700 1 – –
KX-HN7002 KX-HNB700 KX-HNC700 1 KX-HNC710 1
KX-HN7003 KX-HNB700 KX-HNC700 1 KX-HNC710 2
KX-HN1007 KX-HNB700 KX-HNC700 1 KX-HNC710 2
Accessory information
Supplied accessories
No. Accessory item/Part number
Qty.
KX-HN7001 KX-HN7002
KX-HN7003
K
X-HN1007
A AC adaptor for access point/
P
NWYAB700W00
1 1 1
B Ethernet cable/PNWYAB700W01 1 1 1
C USB cable/PNWYAC700W00 1 1 1
D Wall mounting adaptor for front door
c
amera/PNWYAC700W01
1 1 1
E Spacer for front door camera/
P
NWYAC700W01
1 1 1
F Wall mounting screws 25 mm (1 inch)/
P
NWYAC700W02
*1
3 5 7
G Suspension wire tool
–
Safety wire: 1
XXXX
– Washer: 1
The washer for attaching safety wire
to camera ø12 mm (15/32 inches)/
xxxx
– Screw: 1
The screw for attaching the safety
wire to a wall or ceiling 10 mm
(3/8 inches)/xxxx
– Screw safety wire: 1
The screw safety wire for attaching
the safety wire to the camera
- 1 1
For assistance, please visit http://shop.panasonic.com/support
3
Introduction
HN7001(enen)1228ver.030.pdf3 2017/12/2816:21:52
n
For KX-HN1007
H microSD card - - 1
*1 The supplied screws can be used as follows.
–
3 screws for the front door camera
– 2 screws for each outdoor camera
A
B C D E F
G H
Additional accessories
m
icroSD card (not supplied)
A commercially-available microSD card must be inserted into the access point in order to record
images from cameras. The following types of microSD cards are supported.
R microSD / SDHC / SDXC card: Up to 128 GB
Other information
R D
esign and specifications are subject to change without notice.
R The illustrations in these instructions may vary slightly from the actual product.
Trademarks
R m
icroSDHC, microSDXC Logos are trademarks of SD-3C, LLC.
R iPhone and iPad are registered trademarks of Apple Inc.
R Android and Google Play are registered trademarks or trademarks of Google Inc.
R Microsoft, Windows, and Internet Explorer are either registered trademarks or trademarks of
Microsoft Corporation in the United States and/or other countries.
R WPA™ and WPA2™ are registered trademarks or trademarks of Wi-Fi Alliance®.
R All other trademarks identified herein are the property of their respective owners.
Notice
R T
he access point supports microSDHC and microSDXC memory cards. In this document, the
term “microSD card” is used as a generic term for any of the supported cards.
R HomeHawk Front Door is referred to as front door camera or camera in this document.
R HomeHawk Outdoor is referred to as outdoor camera or camera in this document.
4
For assistance, please visit http://shop.panasonic.com/support
Introduction
HN7001(enen)1228ver.030.pdf4 2017/12/2816:21:52
Expanding your camera
Outdoor camera (optional): KX-HNC710
You can expand your camera system by registering optional
c
amera units (16 max.) to the access point.
For assistance, please visit http://shop.panasonic.com/support
5
Introduction
HN7001(enen)1228ver.030.pdf5 2017/12/2816:21:52
Graphical symbols for use on equipment and their
d
escriptions
Symbol Explanation Symbol Explanation
Alternating current (A.C.) Class P
equipment
(equipment in which
protection against electric
shock relies on Double
Insulation or Reinforced
Insulation)
Direct current (D.C.) “ON” (power)
Protective earth “OFF” (power)
Protective bonding earth Stand-by (power)
Functional earth “ON”/“OFF” (power;
p
ush-push)
For indoor use only Caution, risk of electric
s
hock
About this system
R T
his system is an auxiliary system; it is not
designed to provide complete protection
from property loss. Panasonic will not be
held responsible in the event that property
loss occurs while this system is in operation.
R The system’s wireless features are subject
to interference, therefore functionality in all
situations cannot be guaranteed.
Panasonic will not be held responsible for
injury or damage to property that occurs in
the event of wireless communication error
or failure.
For your safety
To prevent severe injury and loss of life/
property, read this section carefully before
using the product to ensure proper and safe
o
peration of your product.
WARNING
Power connection
R F
or the access point, use only the power
source marked on the product. For the
cameras, 5.0 V, 1.0 A or higher power
source.
R Do not overload power outlets and
extension cords. This can result in the risk
of fire or electric shock.
R Completely insert the AC adaptor/power
plug into the power outlet or micro-USB
connector into the power supply device’s
micro-USB jack. Failure to do so may
cause electric shock and/or excessive heat
resulting in a fire.
6
For assistance, please visit http://shop.panasonic.com/support
Important Information
HN7001(enen)1228ver.030.pdf6 2017/12/2816:21:52
R R
egularly remove any dust, etc. from the
AC adaptor/power plug by pulling it from
the power outlet, then wiping with a dry
cloth. Accumulated dust may cause an
insulation defect from moisture, etc.
resulting in a fire.
R Unplug the product from power outlets if it
emits smoke, an abnormal smell, or makes
an unusual noise. These conditions can
cause fire or electric shock. Confirm that
smoke has stopped emitting and contact us
at http://shop.panasonic.com/support
R Unplug from power outlets and never touch
the inside of the product if its casing has
been broken open. Danger of electric shock
exists.
R Never touch the plug with wet hands.
Danger of electric shock exists.
R Do not connect non-specified devices.
Installation
R T
o prevent the risk of fire or electrical
shock, do not expose the access point to
rain or any type of moisture.
R Do not place or use this product near
automatically controlled devices such as
automatic doors and fire alarms. Radio
waves emitted from this product may cause
such devices to malfunction resulting in an
accident.
R Do not allow the power cord to be
excessively pulled, bent or placed under
heavy objects.
R Do not mount the bracket in a location
higher than 2.2 m, in an unstable location,
in a location subject to frequent vibration, or
on a weak wall. (Do not mount on gypsum
board, concrete blocks, wooden materials
exposed to the outdoors, walls with very
rough surfaces, or surfaces that are
narrower than the width of the wall mount
bracket.) There is a risk of injury if the
product falls, or of fire or electric shock if
water enters the product.
R Keep small parts (microSD cards, screws,
etc.) out of the reach of children. There is a
risk of swallowing. In the event they are
swallowed, seek medical advice
immediately.
Operating safeguards
R U
nplug the product from power outlets
before cleaning. Do not use liquid or
aerosol cleaners.
R Do not disassemble the product.
R Never put metal objects inside the product.
If metal objects enter the product, turn off
the circuit breaker and contact an
authorized service center.
Medical
R C
onsult the manufacturer of any personal
medical devices, such as pacemakers or
hearing aids, to determine if they are
adequately shielded from external RF
(radio frequency) energy. Wireless LAN
features operate between 2.412 GHz and
2.462 GHz with a peak transmission power
as following:
– Access point: 200 mW
– Front door camera/Outdoor camera:
100 mW
R Do not use the product in health care
facilities if any regulations posted in the
area instruct you not to do so. Hospitals or
health care facilities may be using
equipment that could be sensitive to
external RF energy.
CAUTION
Installation and location
R N
ever install wiring during a lightning storm.
R Although this camera conforms to the IPX5*
code, do not intentionally expose it to
water.
*IPX5 indicates that the product is
protected against water jets: water
projected at all angles through a 6.3 mm
(1/4 inches) nozzle flow rate of 12.5 liters/
minute at a pressure of 30 kN/m2 for 3
minutes from a distance of 3 meters (9 feet
10 inches).
R Although this camera conforms to the IP6X*
code, do not intentionally expose it to grit
and dust.
*IP6X indicates that the product is
protected against grit and dust: this product
has shown the capabilities of preventing
For assistance, please visit http://shop.panasonic.com/support
7
Important Information
HN7001(enen)1228ver.030.pdf7 2017/12/2816:21:52
dust from entering inside the product after
t
he product was in a device that contained
dust with a diameter of 75 μm or less for 8
hours and was shaken and removed from
that device.
R The AC adaptor and the USB cable are
used as the main disconnect device.
Ensure that the AC outlet is installed near
the product and is easily accessible.
Preventing accidents and injuries
R T
he safety wire must be used when
mounting the product. There is a risk of
injury if the product falls. (KX-HN7002/
KX-HN7003/KX-HN1007)
R Do not put your ear(s) near the speaker, as
loud sounds emitted from the speaker may
cause hearing impairment.
Important safety
i
nstructions
When using your product, basic safety
precautions should always be followed to
reduce the risk of fire, electric shock, and
injury to persons, including the following:
1. Use only the power cord indicated in this
document.
SAVE THESE INSTRUCTIONS
Security cautions
T
ake appropriate measures to avoid the
following security breaches when using this
product.
– Leaks of private information
– Unauthorized use of this product
– Unauthorized interference or suspension of
the use of this product
Take the following measures to avoid security
breaches:
R Configure the access point that connects
your mobile device to this product to use
encryption for all wireless communication.
R You may be vulnerable to security
breaches if the unit is used with the login
password at its default value. Configure
y
our own value for this settings.
R Do not use passwords that could be easily
guessed by a third party. If you keep a
record of your passwords, protect that
record. Change passwords regularly.
R If you lose your mobile device, change the
password used to access this product.
R If you enable the product’s auto login
feature, enable the screen lock or similar
security feature on your mobile device.
R Take care when performing important
security related operations such as
initializing settings, etc.
R To prevent disclosure of personal
information, enable the screen lock or
similar security feature on your mobile
device.
R When submitting the product for repair,
make a note of any important information
stored in the product, as this information
may be erased or changed as part of the
repair process.
R Before handing the product over to a third
party for repair or other purposes, perform
a factory data reset to erase any data
stored in the product and remove the
microSD card. Use only trusted repair
services authorized by Panasonic.
R Before disposing of the product, perform a
factory data reset to erase any data stored
in the product. Remove and erase the
microSD card.
R If your mobile device will no longer be used
with the product, delete your mobile
device’s registration from the product and
delete the corresponding app from your
mobile device.
R If this product experiences a power outage,
its date and time setting may become
incorrect. In this case, the date and time
setting will be automatically corrected when
your mobile device and this product are
connected to the same wireless network.
Additionally, note the following.
R Communications may be interrupted
depending on network conditions and
wireless signal quality.
R This product may be used in ways that
violate the privacy or publicity rights of
8
For assistance, please visit http://shop.panasonic.com/support
Important Information
HN7001(enen)1228ver.030.pdf8 2017/12/2816:21:52
others. You are responsible for the ways in
w
hich this product is used.
For best performance
Product location/avoiding noise
T
he access point and cameras use radio
waves to communicate with each other.
R For maximum coverage and noise-free
communications, place your access point:
– at a convenient, high, and central
location with no obstructions.
– away from electronic appliances such as
TVs, radios, personal computers,
wireless devices, or other phones.
– facing away from radio frequency
transmitters, such as external antennas
of mobile phone cell stations (Avoid
putting the access point on a bay
window or near a window.)
R If the reception for the access point is not
satisfactory, move this to another location.
Environment
R K
eep the product away from electrical noise
generating devices, such as fluorescent
lamps and motors.
R The product should be kept free from
excessive smoke, dust, high temperature,
and vibration.
R Do not expose this product to direct
sunlight or other forms of powerful light
such as halogen lights for long periods of
time. (This may damage the image sensor.)
R Do not place heavy objects on top of the
product.
R When you leave the product unused for
along period of time, do as follows:
– Access point: Unplug the product from
the power outlet.
– Front door camera/Outdoor camera:
Turn off the power switch.
R The product should be kept away from heat
sources such as heaters, kitchen stoves,
etc. It should not be placed in rooms where
the temperature is less than -20 °C (-4 °F)
or greater than 50 °C (122 °F). Damp
basements should also be avoided.
R T
he maximum communication range may
be shortened when the product is used in
the following places: Near obstacles such
as hills, tunnels, underground, near metal
objects such as wire fences, etc.
R Operating the product near electrical
appliances may cause interference. Move
away from the electrical appliances.
Privacy and rights of
p
ortrait
When installing or using the camera, please
take into consideration the rights of others with
regard to privacy.
It is generally said that “privacy” means the
ability of an individual or group to stop
information about themselves from becoming
known to people other than those whom they
choose to give the information. “Rights of
portrait” means the right to be safe from
having your own image taken and used
indiscriminately without consent.
Other information
T
his product has a rechargeable lithium ion
battery. Do not throw into fire, apply heat, or
charge, use, or leave in a high temperature
environment.
– Doing so may cause fluid leak, overheating,
or explosion.
Routine care
R W
ipe the outer surface of the product with a
soft moist cloth.
R Do not use benzine, thinner, or any
abrasive powder.
Camera image quality
R C
amera images may have the following
characteristics.
– Colors in images may differ from the
actual colors.
– When there is light behind the subject
(i.e., backlighting), faces may appear
dark.
For assistance, please visit http://shop.panasonic.com/support
9
Important Information
HN7001(enen)1228ver.030.pdf9 2017/12/2816:21:52
– Image quality may be reduced in dark
l
ocations.
– Images may appear hazy when there
are outdoor lights in use.
Protecting your recordings
R D
o not remove the microSD card or
disconnect the product’s AC adaptor while
reading or writing data to the microSD card.
Data on the card could become corrupted.
R If a microSD card malfunctions or is
exposed to electromagnetic waves or static
electricity, data on the card could become
corrupted or erased. Therefore we
recommend backing up important data to a
computer or other device.
Notice for product disposal, transfer,
o
r return
R This product can store your private/
confidential information. To protect your
privacy/confidentiality, we recommend that
you erase information from the memory
before you dispose of, transfer, or return
the product.
Notice for built-in battery
A
TTENTION:
A lithium ion battery that is recyclable powers
the product you have purchased. Please call
1-800-8-BATTERY (1-800-822-8837) for
information on how to recycle this battery.
WARNING for Lithium Ion (Li-Ion) Battery:
R
isk of fire and burns. Do not open, crush,
heat above 50 °C (122 °F) or incinerate.
Follow the instructions in the operating
instructions.
Remove the built-in rechargeable battery
b
efore disposing of the cameras. Do not
dismantle or replace the battery so that you
can use the camera again. This could cause
fire or an electric shock. Replace it at an
a
uthorized service center.
n Front door camera
1
1
1
2
3
4
5
6
R D
isconnect the power cord from the
camera when removing the battery.
R Perform steps A to F, lift the battery, and
then remove it.
10
For assistance, please visit http://shop.panasonic.com/support
Important Information
HN7001(enen)1228ver.030.pdf10 2017/12/2816:21:52
n
Outdoor camera
1
2
3
4
5
6
7
R D
isconnect the power cord from the
camera when removing the battery.
R Perform steps (A) to (G), lift the battery,
and then remove it.
Notice
For assistance, please visit http://shop.panasonic.com/support
11
Important Information
HN7001(enen)1228ver.030.pdf11 2017/12/2816:21:52
Wireless communication range
T
he wireless communication range of each device in the system from the access point is
approximately 92 m (up to 300 feet). Wireless communication may be unreliable when the
following obstacles are located between the access point and other devices.
R Metal doors or screens
R Walls containing aluminum-sheet insulation
R Walls made of concrete or corrugated iron
R Double-pane glass windows
R Multiple walls
R When using each device on separate floors or in different buildings
Note:
R The access point cannot connect wirelessly to devices other than the front door camera or
outdoor camera.
R The camera’s LED indicator blinks slowly in red if it is out of range of the access point. In this
case, confirm all connections, including those of the access point.
R The signal strength can be checked with the [HomeHawk] app. For more information, refer to
the User’s Guide (page 31).
Information about sensor features
T
he cameras have 2 sensor features that are used for motion detection: a visual sensor and an
infrared sensor (i.e., heat sensor).
Please read the following information before deciding where to install the camera.
Note:
R The camera’s sensor features are not designed to be used in situations that require high
reliability. We do not recommend use of the sensor features in these situations.
R Panasonic takes no responsibility for any injury or damage caused by the use of the camera’s
sensor features.
Detection method
Visual sensor Infrared sensor
The camera detects changes in the images
b
eing displayed.
R The camera detects changes in the
brightness levels of moving objects.
The camera detects temperature differences
of objects in the images being displayed.
R The infrared sensor uses infrared rays to
detect temperature differences within its
range that are emitted naturally by people,
animals, etc.
12
For assistance, please visit http://shop.panasonic.com/support
Installation Location
HN7001(enen)1228ver.030.pdf12 2017/12/2816:21:53
Loading...