Panasonic VDR-D160EB User Manual

LSQT1180(ENG).book 1 ページ２００７年１月２９日　月曜日　午後３時２５分

Cover

Operating Instructions

DVD Video Camera

Model No.VDR-D160EB

Before use, please read these instructions completely.

LSQT1180 A

LSQT1180(ENG).book 2 ページ２００７年１月２９日　月曜日　午後３時２５分

Left/Right

Dear Customer,

We would like to take this opportunity to thank you for purchasing this Panasonic Movie Camera. Please read these Operating Instructions carefully and keep them handy for future reference. Please note that the actual controls and components, menu items, etc. of your Movie Camera may look somewhat different from those shown in the illustrations in these Operating Instructions.

Caution for AC mains lead

For your safety, please read the following text carefully.

This appliance is supplied with a moulded three pin mains plug for your safety and convenience. A 5-ampere fuse is fitted in this plug. Should the fuse need to be replaced please ensure that the replacement fuse has a rating of 5-ampere and that it is approved by ASTA or BSI to BS1362. Check for the ASTA mark Ï or the BSI mark Ì on the body of the fuse.

If the plug contains a removable fuse cover you must ensure that it is refitted when the fuse is replaced. If you lose the fuse cover the plug must not be used until a replacement cover is obtained. A replacement fuse cover can be purchased from your local dealer.

CAUTION!

IF THE FITTED MOULDED PLUG IS UNSUITABLE FOR THE SOCKET OUTLET IN YOUR HOME THEN THE FUSE SHOULD BE REMOVED AND THE PLUG CUT OFF AND DISPOSED OF SAFELY. THERE IS A DANGER OF SEVERE ELECTRICAL SHOCK IF THE CUT OFF PLUG IS INSERTED INTO ANY 13AMPERE SOCKET.

If a new plug is to be fitted please observe the wiring code as stated below. If in any doubt please consult a qualified electrician.

IMPORTANT

The wires in this mains lead are coloured in accordance with the following code: Blue: Neutral, Brown: Live. As these colours may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows:

The wire which is coloured Blue must be connected to the terminal which is marked with the letter N or coloured Black or Blue. The wire which is coloured Brown must be connected to the terminal which is marked with the letter L or coloured Brown or Red.

WARNING: DO NOT CONNECT EITHER WIRE TO THE EARTH TERMINAL WHICH IS MARKED WITH THE LETTER E, BY THE EARTH SYMBOL Ó OR COLOURED GREEN OR GREEN/YELLOW.

THIS PLUG IS NOT WATERPROOF—KEEP DRY.

Before use

Remove the connector cover.

How to replace the Fuse

The location of the fuse differ according to the type of AC mains plug (figures A and B). Confirm the AC mains plug fitted and follow the instructions below. Illustrations may differ from actual AC mains plug.

1) Open the fuse cover with a screwdriver.

Figure A Figure B

2) Replace the fuse and close or attach the fuse cover.

Figure A Figure B

Fuse (5 ampere)

Fuse cover

Fuse (5 ampere)

LSQT1180

LSQT1180(ENG).book 3 ページ２００７年１月２９日　月曜日　午後３時２５分

Information for Your Safety

Product Identification Marking is located on

WARNING:

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR PRODUCT DAMAGE, ≥ DO NOT EXPOSE THIS APPARATUS TO

RAIN, MOISTURE, DRIPPING OR SPLASHING AND THAT NO OBJECTS FILLED WITH LIQUIDS, SUCH AS VASES, SHALL BE PLACED ON THE APPARATUS.

≥ USE ONLY THE RECOMMENDED

ACCESSORIES.

≥ DO NOT REMOVE THE COVER (OR

BACK); THERE ARE NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

CAUTION!

≥ DO NOT INSTALL OR PLACE THIS UNIT

IN A BOOKCASE, BUILT-IN CABINET OR IN ANOTHER CONFINED SPACE. ENSURE THE UNIT IS WELL VENTILATED. TO PREVENT RISK OF ELECTRIC SHOCK OR FIRE HAZARD DUE TO OVERHEATING, ENSURE THAT CURTAINS AND ANY OTHER MATERIALS DO NOT OBSTRUCT THE VENTILATION VENTS.

≥ DO NOT OBSTRUCT THE UNIT’S

VENTILATION OPENINGS WITH NEWSPAPERS, TABLECLOTHS, CURTAINS, AND SIMILAR ITEMS.

≥ DO NOT PLACE SOURCES OF NAKED

FLAMES, SUCH AS LIGHTED CANDLES, ON THE UNIT.

≥ DISPOSE OF BATTERIES IN AN

ENVIRONMENTALLY FRIENDLY MANNER.

the bottom of units.

Use only the recommended accessories.

≥ Do not use any other AV/S cables except the

supplied one.

≥ When you use the cable which are sold

separately, please make sure to use the one whose length is less than 3 meters.

CLASS 1 LASER PRODUCT IEC 60825-1:2001

CAUTION This product contains a laser diode of higher class than 1. To ensure continued safety, do not remove any covers or attempt to gain access to the inside of the product. Refer all servicing to qualified personnel.

The socket outlet shall be installed near the equipment and easily accessible. The mains plug of the power supply cord shall remain readily operable. To completely disconnect this apparatus from the AC Mains, disconnect the power supply cord plug from AC receptacle.

LSQT1180

LSQT1180(ENG).book 4 ページ２００７年１月２９日　月曜日　午後３時２５分

Information on Disposal for Users of Waste Electrical & Electronic Equipment (private households)

This symbol on the products and/or accompanying documents means that used electrical and electronic products should not be mixed with general household waste.

recovery and recycling, please take these products to designated collection points, where they will be accepted on a free of charge basis. Alternatively, in some countries you may be able to return your products to your local retailer upon the purchase of an equivalent new product. Disposing of this product correctly will help to save valuable resources and prevent any potential negative effects on human health and the environment which could otherwise arise from inappropriate waste handling. Please contact your local authority for further details of your nearest designated collection point. Penalties may be applicable for incorrect disposal of this waste, in accordance with national legislation.

For proper treatment,

LSQT1180

For business users in the European Union

If you wish to discard electrical and electronic equipment, please contact your dealer or supplier for further information.

Information on Disposal in other Countries outside the European Union

This symbol is only valid in the European Union. If you wish to discard this product, please contact your local authorities or dealer and ask for the correct method of disposal.

LSQT1180(ENG).book 5 ページ２００７年１月２９日　月曜日　午後３時２５分

∫ Indemnity concerning recording content

The manufacturer shall in no event be liable for the loss of recordings due to malfunction or defect of this unit, its accessories or recordable media.

∫ Carefully observe copyright laws

Recording of pre-recorded tapes or discs or other published or broadcast material for purposes other than your own private use may infringe copyright laws. Even for the purpose of private use, recording of certain material may be restricted.

≥ SDHC Logo is a trademark. ≥ miniSD Logo is a trademark. ≥ The Movie Camera uses copyright-protected technologies and is protected by the patented

technologies and intellectual properties of Japan and the U.S. To use these copyright-protected technologies, authorization of the Macrovision Company is required. It is prohibited to disassemble or modify the Movie Camera.

≥ Manufactured under license from Dolby Laboratories.

“Dolby” and the double-D symbol are trademarks of Dolby Laboratories.

≥ Other names of systems and products mentioned in these instructions are usually the registered

trademarks or trademarks of the manufacturers who developed the system or product concerned.

LSQT1180

LSQT1180(ENG).book 6 ページ２００７年１月２９日　月曜日　午後３時２５分

Contents

Caution for AC mains lead...................2

Information for Your Safety ................. 3

Before using

Features ................................................8

Accessories ........................................ 11

Parts identification and handling...... 12

Using the LCD monitor............................ 15

Using the viewfinder ................................ 15

Discs and cards..................................16

Discs that can be used on this unit ......... 16

Cards that you can use with this unit ...... 19

Disc and card handling............................ 20

Setup

Power supply ......................................21

Charging the battery................................ 21

Connecting to the AC outlet .................... 24

Turning the unit on/off ............................. 25

Inserting/removing a disc..................26

Inserting/removing an SD card ......... 28

Selecting a mode................................29

How to use the joystick......................30

Switching the language .....................34

Using the menu screen......................35

Setting date and time.........................37

Adjusting LCD monitor/viewfinder ...39

Recording

Before recording................................ 40

Recording motion pictures............... 41

Changing the recording mode of

the motion picture ....................................43

Recording still pictures..................... 44

Various recording functions ............. 46

Zoom in/out function ................................ 46

Recording yourself...................................47

Soft skin mode.........................................48

Fade in/fade out function .........................49

Backlight compensation function .............51

Self-timer recording ................................. 52

Wind noise reduction function .................53

Cinema mode ..........................................53

Night view function .................................. 54

Image stabilizer function..........................54

Manual recording functions.............. 55

Scene mode ............................................55

Manual focus adjustment......................... 57

White balance..........................................58

Manual shutter speed/aperture

adjustment...............................................60

Playback

Motion picture playback.................... 61

Still picture playback......................... 64

Playing back still pictures

as a slide show ........................................65

LSQT1180

LSQT1180(ENG).book 7 ページ２００７年１月２９日　月曜日　午後３時２５分

Editing

Editing scenes.................................... 66

Deleting scenes .......................................66

Dividing a scene......................................68

Combining scenes ................................... 69

Using playlists.................................... 70

What is a playlist?....................................70

Creating a new playlist ............................71

Playing back a playlist .............................72

Editing a playlist.......................................73

Editing still pictures........................... 79

Deleting still pictures................................79

Locking still pictures ................................81

DPOF setting...........................................82

Disc and card management

Formatting discs and cards .............. 83

Formatting discs ......................................83

Formatting an SD card ............................ 84

Finalizing a disc ................................. 85

Finalizing a disc.......................................85

Un-finalizing a DVD-RW .......................... 86

Protecting a disc ................................ 87

Displaying disc information.............. 88

With other products

With a TV .............................................89

Playback on TV....................................... 89

With a DVD recorder/player...............90

Playback on a DVD recorder,

DVD player, computer etc. ...................... 90

Copying recordings onto

a DVD recorder’s hard disk ..................... 91

With a VCR ..........................................92

Dubbing images onto other

video devices .......................................... 92

With a printer (PictBridge).................93

Others

Menus ..................................................96

Menu list.................................................. 96

Setup menu............................................. 98

Indications...........................................99

Indications............................................... 99

Messages.............................................. 101

Functions that cannot be used

simultaneously ...................................... 103

Frequently asked questions ............104

Troubleshooting ...............................105

Cautions for use ...............................109

Explanation of terms........................114

Specifications ................................... 116

Number of recordable pictures

on an SD card........................................118

Index ..................................................119

LSQT1180

LSQT1180(ENG).book 8 ページ２００７年１月２９日　月曜日　午後３時２５分

Before using

Features

∫ Easy recording! (l 41)

No need to search for the recording start position. The new recording will not overwrite any previously recorded scene.

∫ Easy playback! (l 61)

Recorded scenes are displayed as thumbnails. You can easily search for the scenes you want to watch.

Before using

LSQT1180

LSQT1180(ENG).book 9 ページ２００７年１月２９日　月曜日　午後３時２５分

Features

∫ Editing scenes! (l 66, 70)

You can create an original video (playlist) by collecting your favourite scenes together and then easily dub this video to a VCR or a DVD recorder hard disk.

If you insert a DVD-RW or a DVD-R recorded on this unit that has not been finalized in another device such as a DVD recorder or a computer, the disc may become unusable. Be sure to finalize the disc on this unit before inserting it in other devices. (l 85)

∫ Using with DVD player/recorder! (l 90)

Just insert the disc into a DVD player/recorder compatible with 8 cm discs to play back the scenes recorded with this unit on it. If you have a DVD recorder with hard disk, you can dub scenes recorded on DVD-RAM or DVD-RW (VR format) with this unit to the hard disk.

Before using

LSQT1180

LSQT1180(ENG).book 10 ページ２００７年１月２９日　月曜日　午後３時２５分

Features

∫ Sales and Support Information

Customer Care Centre

≥ For customers within the UK: 08705 357357 ≥ For customers within the Republic of lreland: 01 289 8333 ≥ Visit our website for product information ≥ E-mail: customer.care@panasonic.co.uk

Technical Support for AV Software ≥ For UK, ROI: 08701 505610

Direct Sales at Panasonic UK ≥ Order accessory and consumable items for your product with ease and confidence by phoning

our Customer Care Centre Monday-Thursday 9.00 a.m.-5.30 p.m., Friday 9.30 a.m.- 5.30 p.m. (Excluding public holidays)

≥ Or go on line through our Internet Accessory ordering application at www.panasonic.co.uk ≥ Most major credit and debit cards accepted. ≥ All enquiries transactions and distribution facilities are provided directly by Panasonic UK Ltd. ≥ It couldn't be simpler! ≥ Also available through our Internet is direct shopping for a wide range of finished products, take a

browse on our website for further details.

Interested in purchasing an extended guarantee? Please call 0870 240 6284 or visit our website www.panasonic.co.uk/guarantee

Before using

LSQT1180

LSQT1180(ENG).book 11 ページ２００７年１月２９日　月曜日　午後３時２５分

Accessories

Check the accessories before using this unit.

Battery pack

CGA-DU12

≥ The supplied battery pack is not available as

spare part, see the list of optional batteries below for alternative battery.

AC adaptor

VSK0651B (DE-974GC)

DC cable

K2GJ2DC00015

Optional accessories

AC adaptor (VW-AD11EB) Tripod (VW-CT45E)

Battery pack (lithium/CGA-DU12/1150 mAh) 8 cm DVD-RAM disc (single sided/LM-AF30E)

Battery pack (lithium/CGA-DU14/1360 mAh) 8 cm DVD-RAM disc (double sided/LM-AF60E)

Battery pack (lithium/CGA-DU21/2040 mAh) 8 cm DVD-RW disc (single sided/LM-RW30E)

Wide conversion lens (VW-LW3007E) 8 cm DVD-RW disc (double sided/LM-RW60E)

Tele conversion lens (VW-LT3014E) 8 cm DVD-R disc (single sided/LM-RF30E)

ND filter (VW-LND30E) 8 cm DVD-R disc (double sided/LM-RF60E)

MC protector (VW-LMC30E)

AV/S cable

K2KZ9CB00001

Disc cleaning cloth

VFC3778-2

AC cable

K2CT3CA00004 (RJA0053-3X)

Before using

≥ Some optional accessories may not be available in some countries.

LSQT1180

2 3 4

LSQT1180(ENG).book 12 ページ２００７年１月２９日　月曜日　午後３時２５分

Parts identification and handling

1Lens 2 Microphone (built-in, stereo) 3 White balance sensor (l 59) 4 Terminal cover 5 Audio-video output terminal [A/V] (l 89, 92) 6 USB terminal [ ] (l 93)

≥ When you are operating this unit with a computer, we

recommend an operating environment less than approximately 30 °C and an operating time of approximately 30 minutes.

7 Viewfinder (l 15, 39)

Due to limitations in LCD production technology, there may be some tiny bright or dark spots on the viewfinder screen. However, this is not a malfunction and does not affect the recorded picture.

8 LCD monitor open button [PUSH OPEN] (l 15)

9 DC input terminal [DC/C.C. IN] (l 24) 10 Recording start/stop button (l 41) 11 Power switch [OFF/ON] (l 25) 12 Status indicator (l 25) 13 Mode dial (l 29)

Before using

14 Joystick (l 30)

≥ Move up, down, left or right to select items. ≥ Press the centre to enter the selection.

15 Delete button [ ] (l 66, 77, 79) 16 Menu button [MENU] (l 35) 17 Battery holder (l 22) 18 Eyepiece corrector knob (l 39) 19 Zoom lever [W/T] (l 46)

Volume lever [sVOLr] (l 62)

20 Photo shot button [ ] (l 44) 21 Card access lamp (l 28) 22 Card slot cover (l 28) 23 Card slot (l 28) 24 Tripod receptacle (l 14) 25 Battery release lever [BATTERY RELEASE] (l 22)

18 19 20

22 2523 24

1 1 1

LSQT1180

LSQT1180(ENG).book 13 ページ２００７年１月２９日　月曜日　午後３時２５分

Parts identification and handling

26 Reset button [RESET] (l 108) 27 LCD monitor (l 15)

Due to limitations in LCD production technology, there may be some tiny bright or dark spots on the LCD monitor screen. However, this is not a malfunction and does not affect the recorded picture.

28 Mode select switch [AUTO/MANUAL/FOCUS]

(l 55)

30 31 32 33

29 Speaker 30 Disc eject lever [DISC EJECT] (l 26) 31 Disc access lamp [ACCESS/PC] (l 26) 32 Disc compartment (l 26) 33 Grip belt (l below)

Using grip belt

Adjust the belt length so it fits your hand.

Adjust the belt length and the pad position.

1 Flip the belt. 2 Adjust the length. 3 Fix the belt.

Before using

LSQT1180

LSQT1180(ENG).book 14 ページ２００７年１月２９日　月曜日　午後３時２５分

Parts identification and handling

Fitting the lens cap

Fit the lens cap to protect the surface of the lens. The lens cap and lens cap cord comes preattached to the grip belt.

≥ When not using the lens cap, pull the lens

cap cord in the direction of the arrow. A

≥ When you are not recording, be sure to

cover the lens with the lens cap for protection. B

≥ When you remove the lens cap, press the knobs firmly.

≥ If the lens cap cord has come off

Pass the end of the lens cap cord through the attached eye on the lens cap. Then pass the lens cap through the loop made by itself and pull tight.

Before using

LSQT1180

Tripod receptacle

This is a hole for attaching the unit to the optional tripod. (Please carefully read the operating instructions for how to attach the tripod to the unit.) ≥ When the tripod is used, the card slot cover cannot be opened.

Insert an SD card before attaching this unit to the tripod. (l 28)

LSQT1180(ENG).book 15 ページ２００７年１月２９日　月曜日　午後３時２５分

Parts identification and handling

Using the LCD monitor

You can record the image while viewing it on the LCD monitor.

1 Press the PUSH OPEN button. The LCD

monitor opens slightly. Pull the LCD monitor out in the direction of the arrow.

≥ The viewfinder is now deactivated. ≥ It can open up to 90o.

2 Adjust the angle of the LCD monitor according to your preference.

≥ It can rotate up to 180o A towards the lens or 90o B towards the viewfinder.

PUSH OPEN

≥ The brightness and colour level of the LCD monitor

can be adjusted from the menu. (l 39)

≥ If it is forcibly opened or rotated, the unit may be

damaged or fail.

Using the viewfinder

Pull out the viewfinder.

(l 39, Adjusting viewfinder)

≥ When the LCD monitor is rotated by 180o towards

the lens (when recording yourself), the LCD monitor and the viewfinder will be simultaneously activated.

Before using

LSQT1180

LSQT1180(ENG).book 16 ページ２００７年１月２９日　月曜日　午後３時２５分

Discs and cards

Discs that can be used on this unit

Disc type DVD-RAM

8 cm

Single sided/

DVD-RW

8 cm

Single sided/double sided

double sided

(DVD-RAM

Ver. 2.1)

Recording format DVD Video

Recording format (VR format)

[DVD-RW Ver. 1.1/

2X-SPEED (2X/1X)]

DVD Video Recording format (VR format)

Characteristic Rewritable disc Rewritable

disc

Display on the screen

Indication in these

Before using

instructions

(RAM) (-RW‹VR›) (-RW‹V›) (-R)

Functions

≥ Editing on this unit ¥¥ ––

≥ Playback on other

products

≥ Recording after

finalizing

*1 By formatting the disc, it can be used repeatedly. (l 83) *2 DVD players and DVD recorders that support 8 cm discs. *3 Playback is possible on compatible products. *4 Must be finalized on this unit. (l 85) Playback is possible on compatible products. *5 Must be finalized on this unit. (l 85) *6 Un-finalize the disc. (l 86)

– ¥

Single sided/ double sided

(DVD-R for

General Ver. 2.0)

DVD-Video format (Video format)

One time recording disc

DVD-Video format (Video format)

One time

recording disc

¥: available –: not available

DVD-R

8 cm

–

LSQT1180

LSQT1180(ENG).book 17 ページ２００７年１月２９日　月曜日　午後３時２５分

Discs and cards

≥ Still pictures cannot be recorded on a disc with this unit. ≥ When using double sided disc, you cannot record or play continuously from one side of the disc

to the other. You will need to eject the disc and turn it over.

≥ Discs inserted in a holder, cartridge, or caddy case cannot be used. Always remove bare discs

from these containers prior to use.

≥ It is recommended that you use Panasonic discs. Usually discs compatible with the DVD

standard can be used for recording and playback with no problems. However, some commercially available discs do not meet the DVD standard for quality and performance. If you use one of these discs, you may not be able to record or playback normally. (The message “FOR BEST PERFORMANCE PANASONIC DISC IS RECOMMENDED.” appears.) Refer to the following support site for information about discs that have been confirmed as compatible by Panasonic. http://panasonic.co.jp/pavc/global/cs/e_cam (This website is in English only.)

≥ Discs recorded on this unit may not be playable on other products. ≥ Recording on DVD-R in DVD Video Recording format is not supported. ≥ When using DVD-RW or DVD-R, do not perform the following, as doing so may make the

disc unusable.

– Record on a disc with other products after recording on it with this unit. – Record on a disc with this unit after recording on it with other products. – Insert an un-finalized disc in any other products.

∫ About format types

What is the DVD Video Recording format (VR format)?

This is a format for recording on DVD discs which allows you to record and erase repeatedly and create playlists. You can record on DVD-RAM and DVD-RW in DVD Video Recording format with this unit.

What is the DVD-Video format (Video format)?

By finalizing the disc, it can be played back on most DVD players. You can record on DVD-RW and DVD-R in DVD-Video format with this unit.

Before using

∫ Examples of discs that cannot be used on this unit ≥ DVD-RAM (2.6 GB) Ver. 1.0 ≥ DVD-ROM ≥ MO ≥ DVD-R (3.9 GB) Ver. 1.0 ≥ DVD-Video ≥ MD ≥ DVD-R (4.7 GB) for Authoring Ver. 2.0 ≥ CD-R ≥ iD ≥iRW ≥ CD-RW ≥ Floppy disk ≥iR ≥ CD ≥ CD-ROM ≥ DVD-R DL ≥ LD ≥ Discs other than those with diameter of 8 cm ≥ Dual/double layer discs

LSQT1180

LSQT1180(ENG).book 18 ページ２００７年１月２９日　月曜日　午後３時２５分

Discs and cards

When using brand-new DVD-RW

When using DVD-RW, select whether to record in DVD Video Recording format (VR format) or DVD-Video format (Video format) and then format the disc. (l 17, About format types)

1 When a brand-new DVD-RW is inserted in this unit,

the screen on the right appears. Select [YES], then press the joystick.

2 Select format type, then press the joystick.

VIDEO: DVD-Video format VR: DVD Video Recording format

3 When the confirm screen appears, select [YES], then press the

joystick.

≥ To change the format type, format the disc again.

(l 83) If the disc is formatted, then all the data recorded on the disc will be erased.

Before using

LSQT1180

LSQT1180(ENG).book 19 ページ２００７年１月２９日　月曜日　午後３時２５分

Discs and cards

Cards that you can use with this unit

Card type SD Memory Card SDHC Memory Card

Capacity 8 MB, 16 MB, 32 MB, 64 MB,

128 MB, 256 MB, 512 MB, 1GB, 2GB

Indication in these instructions

This unit is compatible with both SD Memory cards and SDHC Memory cards. You can only use SDHC Memory cards on devices that are compatible with them. You cannot use SDHC Memory cards on devices that are only compatible with SD Memory cards. (When using an SDHC Memory card on another device, be sure to read the operating instructions for that device.)

≥ For the purposes of these operating instructions, SD Memory Card and SDHC Memory Card are

referred to as the “SD card”.

≥ Motion pictures cannot be recorded on an SD card with this unit. ≥ Please confirm the latest information on the following website. (This website is in English only.)

http://panasonic.co.jp/pavc/global/cs/e_cam

≥ This unit supports SD Memory Cards formatted in FAT12 system and FAT16 system based on SD

Memory Card Specifications and SDHC Memory Cards formatted in FAT32 system.

≥ Use this unit to format SD cards. If an SD card is formatted on other products (such as a

computer), the time spent for recording may become longer and you may not be able to use the SD card. (l 84)

≥ We recommend that you use a Panasonic brand SD card. ≥ When the write-protect switch A on SD card is locked, no recording, deletion

or editing will be possible on the card.

≥ Keep the Memory Card out of reach of children to prevent swallowing. ≥ A MultiMediaCard cannot be used on this unit.

4GB

(SD)

Before using

LSQT1180

LSQT1180(ENG).book 20 ページ２００７年１月２９日　月曜日　午後３時２５分

Discs and cards

Disc and card handling

∫ How to hold a disc or card

Do not touch the recorded surface or the terminal surface.

∫ When inserting/removing a disc

Do not allow the recording/playback side of the disc to get fingerprints or dirty. ≥ If there is a scratch or dirt (e.g. dust or fingerprints) on the recording/playback side of the disc,

images cannot be recorded or played back normally and the following phenomena may occur: – Recording or playback become impossible. – Playback image stops momentarily or sound is interrupted during playback. – Block noise appears on playback images. – The message “NO DATA.“ / “PLEASE CHECK THE DISC.” appears.

∫ If there is dirt on the disc

Clean it with the supplied disc cleaning cloth. Wipe the disc from the centre to the outer edge to remove the dirt. Do not use force when wiping the disc as it may scratch it. Also, do not use solvents (thinner, water, antistatic agent, detergent etc.).

Before using

LSQT1180

∫ Handling precautions ≥ Be careful about scratches and dirt. ≥ Do not attach labels or stickers to discs.

(This may cause disc warping and un-balanced rotation, rendering it unusable.)

≥ Write on the label side of the disc only with a soft, oil-based felt pen. Do not use ballpoint pens or

other hard writing implements.

≥ Do not use record cleaning sprays, benzine, thinner, static electricity prevention liquids or any

other solvent.

≥ Do not use scratch-proof protectors or covers. ≥ Do not expose the terminals of the card to water, garbage or dust. ≥ Do not drop, stack, or impact discs. Do not place objects on them. ≥ Do not use the following discs:

– Discs with exposed adhesive from removed stickers or labels. – Discs that are badly warped or cracked. – Irregularly shaped discs, such as heart shapes.

≥ Do not place in the following areas:

– In direct sunlight. – In very dusty or humid areas. – Near a heater. – Locations susceptible to significant difference in temperature (condensation can occur). – Where static electricity or electromagnetic waves occur.

≥ To protect discs and cards, return them to their cases when you are not using them.

LSQT1180(ENG).book 21 ページ２００７年１月２９日　月曜日　午後３時２５分

Setup

Power supply

Charging the battery

When this unit is purchased, the battery is not charged. Charge the battery before using this unit.

Power supply

1 Connect the AC cable to the AC adaptor and the

AC outlet.

2 Put the battery on the battery mount by aligning

the mark, and then securely plug it in.

≥ The output plug of the AC cable is not completely connected to the

AC adaptor socket. As shown in A, there is a gap.

∫ Charging lamp

Lights up: Charging Goes off: Charging completed Flashing: The battery is over discharged (discharged excessively). In a while, the lamp will light up

≥ Battery charging time (l 23) ≥ We recommend using Panasonic batteries. (l 11) ≥ If you use other batteries, we cannot guarantee the

and normal charging will start. When the battery temperature is excessively high or low, the CHARGE lamp flashes and the charging time will be longer than normal.

≥ If the DC cable is connected to the AC adaptor, then

the battery will not charge. Remove the DC cable from the AC adaptor.

quality of this product.

Setup

LSQT1180

LSQT1180(ENG).book 22 ページ２００７年１月２９日　月曜日　午後３時２５分

Power supply

Fitting the battery

Push the battery against the battery holder and slide it until it clicks.

Removing the battery

While sliding the BATTERY RELEASE lever, slide the battery to remove it.

≥ Hold the battery with your hand so it does not fall.

≥ Be sure to turn off the power on this unit and check

that the status indicator and the access lamp are both off before removing the battery.

Setup

LSQT1180

CAUTION

Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer’s instructions.

LSQT1180(ENG).book 23 ページ２００７年１月２９日　月曜日　午後３時２５分

Power supply

Charging time and recordable time

The times shown in the tables below are for when the temperature is 25 oC and the humidity is 60%. If the temperature is higher or lower than 25 oC, the charging time will become longer.

∫ Charging time

Battery model number Voltage/capacity Charging time

Supplied battery/

CGA-DU12 (optional)

CGA-DU14 (optional) 7.2 V/1360 mAh 2 h 45 min

CGA-DU21 (optional) 7.2 V/2040 mAh 3 h 55 min

≥ “2 h 25 min” indicates 2 hours 25 minutes. ≥ The charging time shown in the table are approximations.

∫ Recordable time ≥ The times indicate the recordable time when the viewfinder is used. The times in parentheses

indicate the recordable time when the LCD monitor is used.

≥ The intermittent recordable time refers to recordable time when the recording and stopping

operations are repeated. In reality, it may be shorter than this.

Battery model

number

Supplied

battery/

CGA-DU12

(optional)

CGA-DU14

(optional)

CGA-DU21

(optional)

≥ “1 h 50 min” indicates 1 hour 50 minutes. ≥ The recordable time shown in the table are approximations.

Voltage/

capacity

7.2 V/

1150 mAh

7.2 V/

1360 mAh

7.2 V/

2040 mAh

7.2 V/1150 mAh 2 h 25 min

(When using a DVD-RAM disc)

Recording

mode

Maximum

continuously

recordable time

1h50min

(1 h 40 min)

2h5min

(1 h 50 min)

2h15min

(2 h)

2h20min

(2 h 5 min)

2h35min

(2 h 20 min)

2h50min

(2 h 35 min)

3h30min

(3 h 10 min)

3h55min

(3 h 30 min)

4h20min

(3 h 50 min)

Intermittent

recordable time

55 min

(50 min)

(55 min)

1h5min

(1 h)

1h10min

(1 h)

1h15min

(1 h 10 min)

1h25min

(1 h 15 min)

1h45min

(1 h 35 min)

1h55min

(1 h 45 min)

2h10min

(1 h 55 min)

Setup

LSQT1180

LSQT1180(ENG).book 24 ページ２００７年１月２９日　月曜日　午後３時２５分

Power supply

≥ Along with the reduction of the battery capacity, the

display will change:

####.

If the battery discharges, then ( ) will flash.

≥ The recordable time will become shorter when you

use both the viewfinder and the LCD monitor simultaneously while rotating the LCD monitor frontward to record yourself, etc.

≥ The batteries heat up after use or charging. This

unit will also heat up while being used. This is not a malfunction.

≥ Be aware that the operating time of the battery will

become shorter in low temperatures. We recommend charging a spare battery for use when recording.

Connecting to the AC outlet

The unit is in the standby condition when the AC adaptor is connected. The primary circuit is always “live” as long as the AC adaptor is connected to an electrical outlet.

1 Connect the AC cable to the AC adaptor and

the AC outlet. 2 Connect the DC cable to the AC adaptor. 3 Connect the DC cable to this unit.

≥ Do not use the AC cable for other equipment since the AC

cable is exclusively designed for this unit. Do not use the AC cable from other equipment for this unit.

Setup

LSQT1180

≥ While the DC cable is connected to the AC adaptor,

the battery will not charge.

LSQT1180(ENG).book 25 ページ２００７年１月２９日　月曜日　午後３時２５分

Power supply

Turning the unit on/off

≥ When recording, remove the lens cap before turning the unit on.

If the unit is turned on with the lens cap fitted, the automatic white balance adjustment may not function properly.

How to turn on the power

While pressing the button A, set the OFF/ON switch to ON.

The status indicator B lights red.

≥ The date and time display flashes. Set this. (l 37)

How to turn off the power

While pressing the button A, set the OFF/ON switch to OFF.

The status indicator B goes off.

When the power is turned on for the first time after changing the disc or battery, the unit carries out a recognition procedure to check that there are no problems with the disc. This takes approximately 25 seconds with DVD-RAM. If you want to start using the unit as soon as you turn on the power, do the following.

1) Turn on the power.

2) After “READING DISC...” disappears from the screen, turn off the power. You can start recording approximately 8 seconds after you turn on the power again.

≥ Depending on the condition of the disc, it may take longer than this. ≥ If the date and time are not set, this function does not work.

Setup

LSQT1180

LSQT1180(ENG).book 26 ページ２００７年１月２９日　月曜日　午後３時２５分

Inserting/removing a disc

When inserting or removing the disc, fit the charged battery pack or connect the AC adaptor to the unit. The cover of the disc compartment will not open unless the unit is powered.

1 Slide the DISC EJECT lever once and

release it.

A few moments after the ACCESS/PC lamp blinks,

the cover of the disc compartment will open slightly.

2 Open the cover of the disc compartment by hand and insert/remove

the disc.

∫ Inserting disc

Fit the disc onto the spindle in the centre.

A Recording/playback side B Pickup lens

Click!

Setup

LSQT1180

∫ Removing disc

While pressing down on the spindle, grasp the edge of the disc and gently lift it out.

3 Push the section marked “PUSH CLOSE” on the cover of the disc

compartment to close the cover.

LSQT1180(ENG).book 27 ページ２００７年１月２９日　月曜日　午後３時２５分

∫ Identifying recording/playback sides of disc Single sided disc:

The recording/playback side is opposite to the labelled side.

Double sided disc:

The “SIDE A” recording/playback side is opposite to the “SIDE A” marked side. The “SIDE B” recording/playback side is the “SIDE A” marked side.

Inserting/removing a disc

“SIDE A” mark

The opposite side is the

“SIDE A” recording/ playback

side.

≥ Do not use excessive force when opening the cover. ≥ Do not touch the pickup lens or the recording/

playback side of the disc. This may impair recording and playback.

≥ Insert the disc securely to prevent damage. ≥ When you open the cover, the ACCESS/PC lamp

flashes red. Do not leave the cover open.

≥ If the cover is open, the power will not turn off even

if the OFF/ON switch is set to OFF.

≥ If the disc is not correctly inserted, the cover will not

close. Never try to forcibly close the cover. This could cause damage. Reinsert the disc properly.

≥ If a single sided disc is inserted into the unit with the

printed label facing the inside, an error message will appear. Remove the disc and reinsert it with its

≥ Do not remove the battery pack or disconnect the

AC adaptor while removing the disc or until power is completely turned off. If you do, the cover will not open. If this happens, reattach the battery pack or reconnect the AC adaptor, slide the DISC EJECT lever once, and then release it. A repair disc message may be displayed when the power is turned back on. (l 102, About recovery)

≥ Do not insert anything other than the 8 cm DVD-

RAM, DVD-RW or DVD-R disc into the disc compartment. Doing so could cause malfunctions.

≥ Do not touch the pickup lens or other parts inside

the disc compartment. Be sure not to touch the area around the pickup lens for it becomes extremely hot.

recording/playback side facing the inside.

≥ Do not allow the recording/playback side to become

dirty or scratched.

After inserting a disc/After recording finishes

While the ACCESS/PC lamp is lit, the disc is rotating and disc information is being recorded. If the power supply is interrupted at this time, the disc may become unusable. Do not disconnect the AC adaptor or remove the battery. Also, do not strongly shake or cause impact to the unit.

Setup

LSQT1180

LSQT1180(ENG).book 28 ページ２００７年１月２９日　月曜日　午後３時２５分

Inserting/removing an SD card

Before inserting/removing an SD card, be sure to turn off the power.

If the SD card is inserted or removed with the power turned on, this unit may malfunction or the data recorded on the SD card may be lost.

1 Open the card slot cover.

2 Insert/remove the SD card into/from the card slot.

≥ When inserting an SD card, face the label side A upwards and press

it straight in with one stroke as far as it goes.

≥ When removing the SD card, press the centre of the SD card and then

pull it straight out.

3 Securely close the card slot cover.

∫ Concerning the SD card ≥ Electrical noise, static electricity or failure of this unit or the SD card may damage or erase the

data stored on the SD card. We recommend saving important data on a computer.

Setup

LSQT1180

∫ Card access lamp ≥ When this unit accesses the SD card (reading, recording, playback, erasing, etc.), the access

lamp lights up.

≥ If the following operations are performed when the access lamp is lit, then the SD card or the

recorded data may be damaged or this unit may malfunction.

– Inserting or removing the SD card – Operating the OFF/ON switch or the mode dial

LSQT1180(ENG).book 29 ページ２００７年１月２９日　月曜日　午後３時２５分

Selecting a mode

The mode dial is used to switch between recording and playback modes. Rotate the mode dial slowly but surely. ≥ Do not forcefully turn the dial.

Rotate the mode dial, and set the desired mode pictograph to the position shown in the illustration.

Disc recording mode (l 41) Use this to record motion pictures on a disc.

Disc playback mode (l 61) Use this to play back motion pictures on a disc.

Card recording mode (l 44) Use this to record still pictures on an SD card.

Selecting a mode

Card playback mode (l 64)

Use this to play back still pictures on an SD card.

Setup

LSQT1180

LSQT1180(ENG).book 30 ページ２００７年１月２９日　月曜日　午後３時２５分

How to use the joystick

This unit has a joystick for selecting functions, performing operations, etc. so it is easy to operate this unit with one hand.

Basic operations

Operations on the menu screen and selection of files on the thumbnail view screen, etc.

Move the joystick up, down, left, or right to select an item or file, and then press the joystick to set it.

3 4

≥ Menu screen operations (l 35)

Joystick and screen display

Press the centre of the joystick, and icons will be displayed on the screen. Each press switches the display as follows depending on the mode. (In the disc playback mode or the card playback mode, the icons will be automatically displayed on the screen.)

1 Select by moving up. 2 Select by moving down. 3 Select by moving left. 4 Select by moving right. 5 Press the joystick to select the item.

Setup

LSQT1180

Disc recording mode

(AUTO/MANUAL/FOCUS switch is set to AUTO)

A: The operation icon is off.

Icon Direction Function Page

4 Soft skin mode 48

—

ª 1 Backlight compensation 51

2 Fade 49

+ 90 hidden pages