Panasonic VDR-D150GN User Manual

LSQT1052(ENG).book 1 ページ 2006年1月24日 火曜日 午後7時5分
Cover
Operating Instructions
DVD Video Camera
Model No.VDR-D150GN
Before use, please read these instructions completely.
LSQT1052 B
LSQT1052(ENG).book 2 ページ 2006年1月24日 火曜日 午後7時5分
Left/Right
As this equipment gets hot during use, operate it in a well-ventilated place; do not install this equipment in a confined space such as a bookcase or similar unit.
To reduce the risk of fire, electric shock or product damage, do not expose this equipment to rain, moisture, dripping or splashing and ensure that no objects filled with liquids, such as vases, shall be placed on the equipment.
Movie Camera The rating plate is on the underside of
the Movie Camera.
AC Adaptor The rating plate is on the underside of
the AC Adaptor.
Warning
Do not remove the cover (or back); there are no user serviceable parts inside. Refer servicing to qualified service personnel.
IF THE POWER CORD OF THIS EQUIPMENT IS DAMAGED, IT MUST BE REPLACED WITH AN ELECTRICALLY APPROVED POWER CORD.
-If you see this symbol-
Information on Disposal in other Countries outside the European Union
This symbol is only valid in the European Union. If you wish to discard this product, please contact your local authorities or dealer and ask for the correct method of disposal.
LSQT1052
Use only the recommended accessories.
Keep the Memory Card out of reach of
children to prevent swallowing.
CLASS 1 LASER PRODUCT
IEC 60825-1:2001 CAUTION This product contains a laser diode of higher class than 1. To ensure continued safety, do not remove any covers or attempt to gain access to the inside of the product. Refer all servicing to qualified personnel.
LSQT1052(ENG).book 3 ページ 2006年1月24日 火曜日 午後7時5分
Indemnity concerning recording content
The manufacturer shall in no event be liable for the loss of recordings due to malfunction or defect of this unit, its accessories or recordable media.
Carefully observe copyright laws
Recording of pre-recorded tapes or discs or other published or broadcast material for purposes other than your own private use may infringe copyright laws. Even for the purpose of private use, recording of certain material may be restricted.
SD Logo is a trademark.The Movie Camera uses copyright-protected technologies and is protected by the patented
technologies and intellectual properties of Japan and the U.S. To use these copyright-protected technologies, authorization of the Macrovision Company is required. It is prohibited to disassemble or modify the Movie Camera.
Manufactured under license from Dolby Laboratories.
“Dolby” and the double-D symbol are trademarks of Dolby Laboratories.
Other names of systems and products mentioned in these instructions are usually the registered
trademarks or trademarks of the manufacturers who developed the system or product concerned.
LSQT1052
LSQT1052(ENG).book 4 ページ 2006年1月24日 火曜日 午後7時5分
Contents
Before using
Features ................................................6
Accessories ..........................................8
Parts identification and handling........ 9
Using the LCD monitor............................ 12
Using the viewfinder ................................ 12
Discs and cards..................................13
Discs that can be used on this unit ......... 13
Cards that you can use with this unit ...... 16
Disc and card handling............................ 17
Setup
Power supply ......................................18
Charging the battery................................ 18
Connecting to the AC outlet .................... 21
Turning the unit on/off ............................. 22
Inserting/removing a disc..................23
Inserting/removing an SD card ......... 25
Selecting a mode................................26
How to use the joystick......................27
Switching the language .....................31
Using the menu screen......................32
Setting date and time.........................34
Adjusting LCD monitor/viewfinder ...36
Recording
Before recording................................ 37
Recording motion pictures............... 38
Changing the recording mode of
the motion picture ....................................40
Recording still pictures..................... 41
Various recording functions ............. 43
Zoom in/out function ................................ 43
Recording yourself...................................45
Soft skin mode.........................................45
Fade in/fade out function .........................46
Backlight compensation function .............48
Self-timer recording ................................. 49
Wind noise reduction function .................50
Cinema mode ..........................................50
Night view function .................................. 51
Image stabilizer function..........................52
Manual recording functions.............. 53
Scene mode ............................................53
Manual focus adjustment......................... 55
White balance..........................................56
Manual shutter speed/aperture
adjustment...............................................58
Playback
Motion picture playback.................... 59
Still picture playback......................... 62
Playing back still pictures as a
slide show................................................63
LSQT1052
LSQT1052(ENG).book 5 ページ 2006年1月24日 火曜日 午後7時5分
Editing
Editing scenes.................................... 64
Deleting scenes .......................................64
Dividing a scene......................................66
Combining scenes ................................... 67
Using playlists.................................... 68
What is a playlist?....................................68
Creating a new playlist ............................69
Playing back a playlist .............................70
Editing a playlist.......................................71
Editing still pictures........................... 77
Deleting still pictures................................77
Locking still pictures ................................79
DPOF setting...........................................80
Disc and card management
Formatting discs and cards .............. 81
Formatting discs ......................................81
Formatting an SD card ............................ 82
Finalizing a disc ................................. 83
Finalizing a disc.......................................83
Un-finalizing a DVD-RW .......................... 84
Protecting a disc ................................ 85
Displaying disc information.............. 86
With other products
With a TV .............................................87
Playback on TV....................................... 87
With a DVD recorder/player...............88
Playback on DVD recorder/player........... 88
Copying recordings onto a
DVD recorder’s hard disk........................ 89
With a VCR ..........................................90
Dubbing images onto other
video devices .......................................... 90
With a printer (PictBridge).................91
Others
Menus ..................................................94
Menu list.................................................. 94
Setup menu............................................. 96
Indications...........................................97
Indications............................................... 97
Messages................................................ 99
Functions that cannot be used
simultaneously ...................................... 101
Frequently asked questions ............102
Troubleshooting ...............................103
Cautions for use ...............................107
Explanation of terms........................ 111
Specifications ................................... 113
Number of recordable pictures on
an SD card ............................................115
LSQT1052
LSQT1052(ENG).book 6 ページ 2006年1月24日 火曜日 午後7時5分
Before using
Features
Features
Easy recording! (l 38)
No need to search for the recording start position. The new recording will not overwrite any previously recorded scene.
Easy playback! (l 59)
Recorded scenes are displayed as thumbnails. You can easily search for the scenes you want to watch.
Before using
LSQT1052
LSQT1052(ENG).book 7 ページ 2006年1月24日 火曜日 午後7時5分
Features
Editing scenes! (l 64, 68)
You can create an original video (playlist) by collecting your favourite scenes together and then easily dub this video to a VCR or a DVD recorder hard disk.
Using with DVD player/recorder! (l 88)
Just insert the disc into a DVD player/recorder compatible with 8 cm discs to play back the scenes recorded with this unit on it. If you have a DVD recorder with hard disk, you can dub scenes recorded on DVD-RAM or DVD-RW (VR format) with this unit to the hard disk.
Before using
LSQT1052
LSQT1052(ENG).book 8 ページ 2006年1月24日 火曜日 午後7時5分
Accessories
Accessories
Check the accessories before using this unit.
Battery pack AV/S cable
AC adaptor Disc cleaning cloth
DC cable
AC cable
Optional accessories
AC adaptor (VW-AD11GN) MC protector (VW-LMC30E)
Battery pack (lithium/CGA-DU12/1150 mAh) Tripod (VW-CT45E)
Battery pack (lithium/CGA-DU14/1360 mAh) 8 cm DVD-RAM disc (single sided/LM-AF30E)
Before using
Battery pack (lithium/CGA-DU21/2040 mAh) 8 cm DVD-RAM disc (double sided/LM-AF60E)
Wide conversion lens (VW-LW3007E) 8 cm DVD-RW disc (single sided/LM-RW30E)
Tele conversion lens (VW-LT3014E) 8 cm DVD-RW disc (double sided/LM-RW60E)
ND filter (VW-LND30E) 8 cm DVD-R disc (single sided/LM-RF30E)
Some optional accessories may not be available in some countries.
LSQT1052
2 3 4
7
5
6
LSQT1052(ENG).book 9 ページ 2006年1月24日 火曜日 午後7時5分
Parts identification and handling
Parts identification and handling
1Lens 2 Microphone (built-in, stereo) 3 White balance sensor (l 57) 4 Terminal cover 5 Audio-video output terminal [A/V] (l 87, 90) 6 USB terminal [ ] (l 91)
When you are operating this unit with a computer, we
recommend an operating environment less than approximately 30 °C and an operating time of approximately 30 minutes.
7 Viewfinder (l 12, 36)
Due to limitations in LCD production technology, there may be some tiny bright or dark spots on the viewfinder screen. However, this is not a malfunction and does not affect the recorded picture.
8 LCD monitor open button [PUSH OPEN] (l 12)
9 DC input terminal [DC/C.C. IN] (l 21) 10 Recording start/stop button (l 38) 11 Power switch [OFF/ON] (l 22) 12 Status indicator (l 22) 13 Mode dial (l 26) 14 Joystick (l 27)
Move up, down, left or right to select items.Press the centre to enter the selection.
15 Delete button [ ] (l 64, 75, 77) 16 Menu button [MENU] (l 32) 17 Battery holder (l 19) 18 Eyepiece corrector knob (l 36) 19 Zoom lever [W/T] (l 43)
Volume lever [sVOLUMEr] (l 60) 20 Photo shot button [PHOTO SHOT] (l 41) 21 Card access lamp (l 25) 22 Card slot cover (l 25) 23 Card slot (l 25) 24 Tripod receptacle (l 11) 25 Battery release lever [BATTERY RELEASE] (l 19)
10
1
2
3
4
65
11
7
8
9
18 19 20
21
22 2523 24
1 1 1
1
1
1
Before using
LSQT1052
8
9
LSQT1052(ENG).book 10 ページ 2006年1月24日 火曜日 午後7時5分
Parts identification and handling
26 Reset button [RESET] (l 106)
27 LCD monitor (l 12)
Due to limitations in LCD production technology, there may be some tiny bright or dark spots on the LCD monitor screen. However, this is not a malfunction and does not affect the recorded picture.
26
27
28 Mode select switch [AUTO/MANUAL/FOCUS]
(l 53)
29 Speaker
30 Disc eject lever [DISC EJECT] (l 23)
31 Disc access lamp [ACCESS/PC] (l 23)
32 Disc compartment (l 23)
33 Grip belt (l below)
Using grip belt
Adjust the belt length so it fits your hand.
Adjust the belt length and the pad position.
1 Flip the belt.
2 Adjust the length.
3 Fix the belt.
2
2
30 31 32 33
Before using
10
LSQT1052
1
2
3
LSQT1052(ENG).book 11 ページ 2006年1月24日 火曜日 午後7時5分
Parts identification and handling
Fitting the lens cap
Fit the lens cap to protect the surface of the lens. The lens cap and lens cap cord comes preattached to the grip belt.
When not using the lens cap, pull the lens
cap cord in the direction of the arrow. A
When you are not recording, be sure to
cover the lens with the lens cap for protection. B
When you remove the lens cap, press the knobs firmly.
If the lens cap cord has come off
Pass the end of the lens cap cord through the attached eye on the lens cap. Then pass the lens cap through the loop made by itself and pull tight.
A
Tripod receptacle
This is a hole for attaching the unit to the optional tripod. (Please carefully read the operating instructions for how to attach the tripod to the unit.) When the tripod is used, the card slot cover cannot be opened.
Insert an SD card before attaching this unit to the tripod. (l 25)
B
Before using
11
LSQT1052
LSQT1052(ENG).book 12 ページ 2006年1月24日 火曜日 午後7時5分
Parts identification and handling
Using the LCD monitor
You can record the image while viewing it on the LCD monitor.
1 Press the PUSH OPEN button. The LCD
monitor opens slightly. Pull the LCD monitor out in the direction of the arrow.
The viewfinder is now deactivated.It can open up to 90o.
2 Adjust the angle of the LCD monitor according to your preference.
It can rotate up to 180o A towards the lens or 90o B towards the viewfinder.
BA
PUSH OPEN
The brightness and colour level of the LCD monitor
can be adjusted from the menu. (l 36)
If it is forcibly opened or rotated, the unit may be
damaged or fail.
Before using
Using the viewfinder
Pull out the viewfinder.
(l 36, Adjusting viewfinder)
When the LCD monitor is rotated by 180o towards
the lens (when recording yourself), the LCD monitor and the viewfinder will be simultaneously activated.
12
LSQT1052
LSQT1052(ENG).book 13 ページ 2006年1月24日 火曜日 午後7時5分
Discs and cards
Discs that can be used on this unit
Discs and cards
DIsc type DVD-RAM
8 cm Single sided/ double sided
(DVD-RAM
Ver. 2.1)
Recording format DVD Video
Recording format (VR format)
DVD Video Recording format (VR format)
Characteristic Rewritable disc Rewritable
disc
DVD-RW
8 cm
Single sided/double sided
[DVD-RW Ver. 1.1/
2X-SPEED (2X/1X)]
DVD-Video format (Video format)
One time recording disc
Single sided/ double sided
(DVD-R for
General Ver. 2.0)
DVD-Video format (Video format)
One time
*1
recording disc
DVD-R
8 cm
Display on the screen
Indication in these instructions
(RAM) (-RW‹VR›) (-RW‹V›) (-R)
Functions
Editing on this unit ¥¥ ––
Playback on other
products
*2
Recording after
finalizing
*3
¥
¥
*4
¥
*5
¥
*6
¥
*5
¥
¥: available –: not available
*1 By formatting the disc, it can be used repeatedly. (l 81) *2 DVD players and DVD recorders that support 8 cm discs. *3 Playback is possible on compatible products. *4 Playback is possible on compatible products. (May have to be finalized on this unit.) *5 Must be finalized on this unit. (l 83) *6 Un-finalize the disc. (l 84)
Before using
13
LSQT1052
LSQT1052(ENG).book 14 ページ 2006年1月24日 火曜日 午後7時5分
Discs and cards
Still pictures cannot be recorded on a disc with this unit.When using double sided disc, you cannot record or play continuously from one side of the disc
to the other. You will need to eject the disc and turn it over.
Discs inserted in a holder, cartridge, or caddy case cannot be used. Always remove bare discs
from these containers prior to use.
It is recommended that you use Panasonic discs. Usually discs compatible with the DVD
standard can be used for recording and playback with no problems. However, some commercially available discs do not meet the DVD standard for quality and performance. If you use one of these discs, you may not be able to record or playback normally. (The message “FOR BEST PERFORMANCE PANASONIC DISC IS RECOMMENDED.” appears.) Refer to the following support site for information about discs that have been confirmed as compatible by Panasonic. http://panasonic.co.jp/pavc/global/cs/e_cam (This website is in English only.)
Discs recorded on this unit may not be playable on other products.Recording on DVD-R in DVD Video Recording format is not supported.When using DVD-RW or DVD-R, do not perform the following, as doing so may make the disc
unusable. – Record on a disc with other products after recording on it with this unit. – Record on a disc with this unit after recording on it with other products. – Insert an un-finalized disc in any other products.
About format types
What is the DVD Video Recording format (VR format)?
This is a format for recording on DVD discs which allows you to record and erase repeatedly and create playlists. You can record on DVD-RAM and DVD-RW in DVD
Before using
Video Recording format with this unit.
What is the DVD-Video format (Video format)?
By finalizing the disc, it can be played back on most DVD players. You can record on DVD-RW and DVD-R in DVD-Video format with this unit.
14
LSQT1052
Examples of discs that cannot be used on this unitDVD-RAM (2.6 GB) Ver. 1.0 DVD-ROM MODVD-R (3.9 GB) Ver. 1.0 DVD-Video MDDVD-R (4.7 GB) for Authoring Ver. 2.0 CD-R iD ≥iRW ≥ CD-RW ≥ Floppy disk ≥iR ≥ CD ≥ CD-ROMDVD-R DL LDDiscs other than those with diameter of 8 cmDual/double layer discs
LSQT1052(ENG).book 15 ページ 2006年1月24日 火曜日 午後7時5分
Discs and cards
When using brand-new DVD-RW
When using DVD-RW, select whether to record in DVD Video Recording format (VR format) or DVD-Video format (Video format) and then format the disc. (l 14, About format types)
1 When a brand-new DVD-RW is inserted in this unit,
the screen on the right appears. Select [YES], then press the joystick.
2 Select format type, then press the joystick.
VIDEO: DVD-Video format VR: DVD Video Recording format
3 When the confirm screen appears, select [YES], then press the
joystick.
To change the format type, format the disc again.
(l 81) If the disc is formatted, then all the data recorded on the disc will be erased.
Before using
15
LSQT1052
LSQT1052(ENG).book 16 ページ 2006年1月24日 火曜日 午後7時5分
Discs and cards
Cards that you can use with this unit
Card type SD Memory Card
Capacity 8 MB, 16 MB, 32 MB, 64 MB, 128 MB, 256 MB, 512 MB, 1 GB,
Indication in these instructions
Motion pictures cannot be recorded on an SD card with this unit.Please confirm the latest information on the following website. (This website is in English only.)
http://panasonic.co.jp/pavc/global/cs/e_cam
For the purposes of these operating instructions, SD Memory Card and miniSD™ Card are
referred to as the “SD card”.
This unit supports SD cards formatted in FAT12 system and FAT16 system based on SD Memory
Card Specifications.
Use this unit to format SD cards. If an SD card is formatted on other products (such as a
computer), the time spent for recording may become longer and you may not be able to use the SD card. (l 82)
We recommend that you use a Panasonic brand SD card.Be sure to insert miniSD™ Cards in the dedicated card adaptor before use. Inserting a card in
this unit without the adaptor may damage the unit or the card.
Do not insert an empty card adaptor in this unit. Do not leave the adaptor in this unit while
inserting or removing miniSD™ Cards. This may cause the unit to malfunction.
When the write-protect switch on SD Memory Card is locked, no recording, deletion or editing will
be possible on the card.
Before using
2 GB (Maximum)
(SD)
16
LSQT1052
Write-protect switch Locked status
Keep the memory card out of reach of children to prevent swallowing.A MultiMediaCard cannot be used on this unit.
LSQT1052(ENG).book 17 ページ 2006年1月24日 火曜日 午後7時5分
Discs and cards
Disc and card handling
How to hold a disc or card
Do not touch the recorded surface or the terminal surface.
If there is dirt on the disc
Clean it with the supplied disc cleaning cloth. Wipe the disc from the centre to the outer edge to remove the dirt. Do not use force when wiping the disc as it may scratch it. Also, do not use solvents (thinner, water, antistatic agent, detergent etc.).
Handling precautionsBe careful about scratches and dirt.Do not attach labels or stickers to discs.
(This may cause disc warping and un-balanced rotation, rendering it unusable.)
Write on the label side of the disc only with a soft, oil-based felt pen. Do not use ballpoint pens or
other hard writing implements.
Do not use record cleaning sprays, benzine, thinner, static electricity prevention liquids or any
other solvent.
Do not use scratch-proof protectors or covers.Do not expose the terminals of the card to water, garbage or dust.Do not drop, stack, or impact discs. Do not place objects on them.Do not use the following discs:
– Discs with exposed adhesive from removed stickers or labels. – Discs that are badly warped or cracked. – Irregularly shaped discs, such as heart shapes.
Before using
Do not place in the following areas:
– In direct sunlight. – In very dusty or humid areas. – Near a heater. – Locations susceptible to significant difference in temperature (condensation can occur). – Where static electricity or electromagnetic waves occur.
To protect discs and cards, return them to their cases when you are not using them.
17
LSQT1052
LSQT1052(ENG).book 18 ページ 2006年1月24日 火曜日 午後7時5分
Setup
Power supply
Power supply
Charging the battery
When this unit is purchased, the battery is not charged. Charge the battery before using this unit.
1 Connect the AC cable to the AC adaptor and the
AC outlet.
2 Put the battery on the battery mount by aligning
the mark, and then securely plug it in.
The output plug of the AC cable is not completely connected to the
AC adaptor socket. As shown in A, there is a gap.
Charging lamp
Lights up: Charging Goes off: Charging completed Flashing: The battery is over discharged (discharged excessively). In a while, the lamp will light up
Battery charging time (l 20)We recommend using Panasonic batteries.If you use other batteries, we cannot guarantee the
and normal charging will start. When the battery temperature is excessively high or low, the CHARGE lamp flashes and the charging time will be longer than normal.
If the DC cable is connected to the AC adaptor, then
the battery will not charge. Remove the DC cable from the AC adaptor.
quality of this product.
Setup
A
18
LSQT1052
LSQT1052(ENG).book 19 ページ 2006年1月24日 火曜日 午後7時5分
Fitting the battery
Push the battery against the battery holder and slide it until it clicks.
Removing the battery
While sliding the BATTERY RELEASE lever, slide the battery to remove it.
Hold the battery with your hand so it does not fall.
Be sure to turn off the power on this unit and check
that the status indicator and the access lamp are both off before removing the battery.
Power supply
Setup
19
LSQT1052
LSQT1052(ENG).book 20 ページ 2006年1月24日 火曜日 午後7時5分
Power supply
Charging time and recordable time
The times shown in the tables below are for when the temperature is 25 oC and the humidity is 60%. If the temperature is higher or lower than 25 oC, the charging time will become longer.
Charging time
Battery model number Voltage/capacity Charging time
Supplied battery/
CGA-DU12 (optional)
CGA-DU14 (optional) 7.2 V/1360 mAh 2 h 45 min
CGA-DU21 (optional) 7.2 V/2040 mAh 3 h 55 min
“2 h 25 min” indicates 2 hours 25 minutes.The charging time shown in the table are approximations.
Recordable timeThe times indicate the recordable time when the viewfinder is used. The times in parentheses
indicate the recordable time when the LCD monitor is used.
The intermittent recordable time refers to recordable time when the recording and stopping
operations are repeated. In reality, it may be shorter than this.
Battery model
number
Setup
Supplied
battery/
CGA-DU12
(optional)
CGA-DU14
(optional)
CGA-DU21
(optional)
“1 h 50 min” indicates 1 hour 50 minutes.The recordable time shown in the table are approximations.
Voltage/
capacity
7.2 V/
1150 mAh
7.2 V/
1360 mAh
7.2 V/
2040 mAh
7.2 V/1150 mAh 2 h 25 min
(When using a DVD-RAM disc)
Recording
mode
XP
SP
LP
XP
SP
LP
XP
SP
LP
Maximum
continuously
recordable time
1h50min
(1h40min)
2h5min
(1h50min)
2h15min
(2 h)
2h20min
(2h5min)
2h35min
(2h20min)
2h50min
(2h35min)
3h30min
(3h10min)
3h55min
(3h30min)
4h20min
(3h50min)
Intermittent
recordable time
1h5min
1h10min
1h15min
(1 h 10 min)
1h25min
(1 h 15 min)
1h45min
(1 h 35 min)
1h55min
(1 h 45 min)
2h10min
(1 h 55 min)
55 min
(50 min)
1h
(55 min)
(1 h)
(1 h)
20
LSQT1052
LSQT1052(ENG).book 21 ページ 2006年1月24日 火曜日 午後7時5分
Power supply
Along with the reduction of the battery capacity, the
display will change:
####.
If the battery discharges, then ( ) will flash.
The recordable time will become shorter when you
use both the viewfinder and the LCD monitor simultaneously while rotating the LCD monitor frontward to record yourself, etc.
The batteries heat up after use or charging. This
unit will also heat up while being used. This is not a malfunction.
Be aware that the operating time of the battery will
become shorter in low temperatures. We recommend charging a spare battery for use when recording.
Connecting to the AC outlet
1 Connect the AC cable to the AC adaptor and
the AC outlet. 2 Connect the DC cable to the AC adaptor. 3 Connect the DC cable to this unit.
Do not use the AC cable for other equipment since the AC
cable is exclusively designed for this unit. Do not use the AC cable from other equipment for this unit.
While the DC cable is connected to the AC adaptor,
the battery will not charge.
Setup
21
LSQT1052
B
LSQT1052(ENG).book 22 ページ 2006年1月24日 火曜日 午後7時5分
Power supply
Turning the unit on/off
When recording, remove the lens cap before turning the unit on.
If the unit is turned on with the lens cap fitted, the automatic white balance adjustment may not function properly.
How to turn on the power
While pressing the button A, set the
OFF/ON switch to ON.
The status indicator B lights red.
A
The date and time display flashes. Set this. (l 34)
How to turn off the power
While pressing the button A, set the OFF/ON switch to
OFF.
The status indicator B goes off.
When the power is turned on for the first time after changing the disc or battery, the unit carries out a recognition procedure to check that there are no problems with the disc.
Setup
This takes approximately 25 seconds with DVD-RAM. If you want to start using the unit as soon as you turn on the power, do the following.
1) Turn on the power.
2) After “READING DISC...” disappears from the screen, turn off the power. You can start recording approximately 8 seconds after you turn on the power again.
Depending on the condition of the disc, it may take longer than this.If the date and time are not set, this function does not work.
B
A
LSQT1052
22
LSQT1052(ENG).book 23 ページ 2006年1月24日 火曜日 午後7時5分
Inserting/removing a disc
Inserting/removing a disc
When inserting or removing the disc, fit the charged battery pack or connect the AC adaptor to the unit. The cover of the disc compartment will not open unless the unit is powered.
1 Slide the DISC EJECT lever once and
release it.
A few moments after the ACCESS/PC lamp blinks,
the cover of the disc compartment will open slightly.
2 Open the cover of the disc compartment by hand and insert/remove
the disc.
Inserting disc
Fit the disc onto the spindle in the centre.
A Recording/playback side B Pickup lens
Click!
AB
Removing disc
While pressing down on the spindle, grasp the edge of the disc and gently lift it out.
3 Push the section marked “PUSH CLOSE” on the cover of the disc
compartment to close the cover.
Setup
23
LSQT1052
LSQT1052(ENG).book 24 ページ 2006年1月24日 火曜日 午後7時5分
Inserting/removing a disc
Identifying recording/playback sides of disc
Single sided disc:
The recording/playback side is opposite to the labelled side.
Double sided disc:
The “SIDE A” recording/playback side is opposite to the “SIDE A”
marked side. The “SIDE B” recording/playback side is the “SIDE A”
marked side.
“SIDE A” mark
M
/
S
A
I
D
R
-
E
D
A
V
D
The opposite side is the
“SIDE A” recording/ playback
side.
Do not use excessive force when opening the cover.
Do not touch the pickup lens or the recording/
playback side of the disc. This may impair recording and playback.
Insert the disc securely to prevent damage.
When you open the cover, the ACCESS/PC lamp
flashes red. Do not leave the cover open.
If the cover is open, the power will not turn off even
if the OFF/ON switch is set to OFF.
If the disc is not correctly inserted, the cover will not
close. Never try to forcibly close the cover. This could cause damage. Reinsert the disc properly.
If a single sided disc is inserted into the unit with the
printed label facing the inside, an error message will appear. Remove the disc and reinsert it with its
Do not remove the battery pack or disconnect the
AC adaptor while removing the disc or until power is completely turned off. If you do, the cover will not open. If this happens, reattach the battery pack or reconnect the AC adaptor, slide the DISC EJECT lever once, and then release it. A repair disc message may be displayed when the power is turned back on. (l 100, About recovery)
Do not insert anything other than the 8 cm DVD-
RAM, DVD-RW or DVD-R disc into the disc compartment. Doing so could cause malfunctions.
Do not touch the pickup lens or other parts inside
the disc compartment. Be sure not to touch the area around the pickup lens for it becomes extremely hot.
recording/playback side facing the inside.
Do not allow the recording/playback side to become
dirty or scratched.
Setup
After inserting a disc/After recording finishes
While the ACCESS/PC lamp is lit, the disc is rotating and disc information is being recorded. If the power supply is interrupted at this time, the disc may become unusable. Do not disconnect the AC adaptor or remove the battery. Also, do not strongly shake or cause impact to the unit.
24
LSQT1052
A
LSQT1052(ENG).book 25 ページ 2006年1月24日 火曜日 午後7時5分
Inserting/removing an SD card
Inserting/removing an SD card
Before inserting/removing an SD card, be sure to turn off the power.
If the SD card is inserted or removed with the power turned on, this unit may malfunction or the data recorded on the SD card may be lost.
1 Open the card slot cover.
2 Insert/remove the SD card into/from the card slot.
When inserting an SD card, face the label side A upwards and press
it straight in with one stroke as far as it goes.
When removing the SD card, press the centre of the SD card and then
pull it straight out.
3 Securely close the card slot cover.
Concerning the SD cardElectrical noise, static electricity or failure of this unit or the SD card may damage or erase the
data stored on the SD card. We recommend saving important data on a computer.
Card access lampWhen this unit accesses the SD card (reading, recording, playback, erasing, etc.), the access
lamp lights up.
If the following operations are performed when the access lamp is lit, then the SD card or the
recorded data may be damaged or this unit may malfunction.
– Inserting or removing the SD card – Operating the OFF/ON switch or the mode dial
Setup
25
LSQT1052
LSQT1052(ENG).book 26 ページ 2006年1月24日 火曜日 午後7時5分
Selecting a mode
Selecting a mode
The mode dial is used to switch between recording and playback modes.
Rotate the mode dial slowly but surely.
Do not forcefully turn the dial.
Rotate the mode dial, and set the desired
mode pictograph to the position shown in
the illustration.
Disc recording mode (l 38) Use this to record motion pictures on a disc.
Disc playback mode (l 59) Use this to play back motion pictures on a disc.
Card recording mode (l 41) Use this to record still pictures on an SD card.
Setup
Card playback mode (l 62)
Use this to play back still pictures on an SD card.
26
LSQT1052
LSQT1052(ENG).book 27 ページ 2006年1月24日 火曜日 午後7時5分
How to use the joystick
How to use the joystick
This unit has a joystick for selecting functions, performing operations, etc. so it is easy to operate this unit with one hand.
Basic operations
Operations on the menu screen and selection of files on the thumbnail view screen, etc.
Move the joystick up, down, left, or right to select an item or file, and then press the joystick to set it.
1
3 4
2
Menu screen operations (l 32)
5
Joystick and screen display
Press the centre of the joystick, and icons will be displayed on the screen. Each press switches the display as follows depending on the mode. (In the disc playback mode or the card playback mode, the icons will be automatically displayed on the screen.)
1 Select by moving up. 2 Select by moving down. 3 Select by moving left. 4 Select by moving right. 5 Press the joystick to select the item.
Disc recording mode
(AUTO/MANUAL/FOCUS switch is set to AUTO)
A: The operation icon is off.
Icon Direction Function Page
4 Soft skin mode 45
ª 1 Backlight compensation 48
2 Fade 46
A
Setup
27
LSQT1052
LSQT1052(ENG).book 28 ページ 2006年1月24日 火曜日 午後7時5分
How to use the joystick
Disc recording mode (AUTO/MANUAL/FOCUS switch is set to MANUAL)
A: The operation icon is off.
Icon Direction Function Page
4 Soft skin mode 45
(1/2)
ª 1 Backlight compensation 48
(2/2)
s r
2 Fade 46
Manual white balance set
3
4
21
(Only when manual white balance adjustment mode is selected)
White balance 56
Shutter speed 58
Iris or gain value 58
White balance mode selection, manual adjustments
A
57
55, 56, 58
Setup
28
LSQT1052
Disc playback mode
A: The operation icon is off.
Icon Direction Function Page
1/;3Playback/pause 59
∫4Stop playback and show thumbnails 59
:
2; Reverse slow/frame playback (during pause) 60 9 ;1 Forward slow/frame playback (during pause) 60
2
1
Rewind, skip (during playback) 59
Fast forward, skip (during playback) 59
A
LSQT1052(ENG).book 29 ページ 2006年1月24日 火曜日 午後7時5分
Card recording mode
(AUTO/MANUAL/FOCUS switch is set to AUTO)
A: The operation icon is off.
Icon Direction Function Page
4 Soft skin mode 45
Ø 2 Self timer 49
ª 1 Backlight compensation 48
Card recording mode
(AUTO/MANUAL/FOCUS switch is set
to MANUAL)
A: The operation icon is off.
Icon Direction Function Page
4 Soft skin mode 45
(1/2)
(2/2)
Ø 2 Self timer 49
ª 1 Backlight compensation 48
3
4
s r
21
Manual white balance set (Only when manual white balance adjustment mode is selected)
White balance 56
Shutter speed 58
Iris or gain value 58
White balance mode selection, manual adjustments
How to use the joystick
A
A
Setup
57
55, 56, 58
29
LSQT1052
LSQT1052(ENG).book 30 ページ 2006年1月24日 火曜日 午後7時5分
How to use the joystick
Card playback mode (When [PICTURE] is selected)
A: The operation icon is off.
Icon Direction Function Page
∫4Stop playback and show thumbnails 62
E2Playback previous picture 62 D1Playback next picture 62
Card playback mode (When [SLIDE SHOW] is selected)
A: The operation icon is off.
Icon Direction Function Page
1/;3Slide show start/pause 63
∫4Stop playback and show thumbnails 62
E2Playback previous picture (during pause) 62
Setup
D1Playback next picture (during pause) 62
A
A
30
LSQT1052
Loading...
+ 86 hidden pages