Panasonic TH-65VX300ER Operating Instructions

Operating Instructions
High Defi nition Plasma Display
Model No.
TH-65VX300ER
English
Please read these instructions before operating your set and retain them for future reference.
Welcome to the Panasonic family of customers. We hope that you will have many years of enjoyment from your new Plasma Display. To obtain maximum benefit from your set, please read these Instructions before making any adjustments, and retain them for future reference. Retain your purchase receipt also, and note down the model number and serial number of your set in the space provided on the rear cover of these instructions. Visit our Panasonic Web Site http://panasonic.net
Table of Contents
Important Safety Notice ........................................... 3
Safety Precautions ................................................... 4
3D Safety Precautions ............................................. 7
Accessories .............................................................. 9
Accessories Supply ................................................. 9
Remote Control Batteries ........................................ 9
Connections ............................................................ 10
Speaker connection ............................................... 10
AC cord connection and fi xing, cable fi xing ........... 10
Video equipment connection ..................................11
COMPONENT / RGB IN connection ..................... 12
HDMI connection ................................................... 12
PC Input Terminals connection .............................. 13
SERIAL Terminals connection ............................... 14
Power On / Off ......................................................... 15
Selecting the input signal ...................................... 18
Basic Controls ........................................................ 19
ASPECT Controls ................................................... 21
Viewing 3D images ................................................. 22
To view the 3D images .......................................... 22
Troubleshooting for 3D Eyewear .......................... 23
Table of images that can be seen for each 3D
Picture Format and the source image format ........ 23
On-Screen Menu Displays ..................................... 24
Adjusting Pos. /Size ............................................... 25
Picture Adjustments ............................................... 28
Advanced settings ................................................. 30
Colour space adjustment (Colour Gamut) ............. 32
Picture Profi les ....................................................... 34
Saving profi les ....................................................... 35
Loading profi les ..................................................... 36
Editing profi les ....................................................... 37
Locking profi les ..................................................... 38
Sound Adjustment .................................................. 40
SDI Sound Output ................................................. 40
Setup menu ............................................................. 41
Component / RGB-in select ................................... 41
YUV / RGB-in select .............................................. 41
External scaler mode ............................................. 42
Power save ............................................................ 43
Standby save ......................................................... 43
PC Power management ........................................ 43
No signal power off ................................................ 43
No activity power off .............................................. 43
OSD design ........................................................... 44
OSD position ......................................................... 44
OSD Language ...................................................... 44
3D Settings ............................................................ 45
Signal menu .......................................................... 46
Waveform Monitor ................................................. 48
Marker Settings ..................................................... 49
RGB/MONO settings ............................................. 51
Screensaver .......................................................... 52
Extended life settings ............................................ 54
Customizing the Input labels ................................. 57
Function Button Settings ....................................... 57
Day/Time Setup / On/Off Timer Setup ................... 58
Network Setup ....................................................... 59
Options Adjustments ............................................. 60
3D Safety Precautions (To hide 3D Safety
Precautions) .......................................................... 61
Using FUNCTION button ........................................ 62
Using Network Function ........................................ 64
Example of Network Connection ........................... 64
Command Control ................................................. 64
PJLink™ Protocol .................................................. 65
Using Web Browser Control .................................. 66
Before Using Web Browser Control....................... 66
Access from Web Browser .................................... 66
Display Control (BASIC CONTROL/OPTION
CONTROL Screen) ............................................... 67
NETWORK SETTING (Network Setup Screen) .... 68
Password Setting (Password Setup Screen) ........ 68
Troubleshooting ..................................................... 69
List of Aspect Modes ............................................. 70
Applicable Input Signals ........................................ 71
Shipping condition ................................................. 72
Specifi cations ......................................................... 73
2
Important Safety Notice
IMPORTANT: THE MOULDED PLUG
WARNING
1) To prevent damage which may result in fi re or shock hazard, do not expose this appliance to dripping or splashing.
Do not place containers with water (fl ower vase, cups, cosmetics, etc.) above the set. (including on
shelves above, etc.)
No naked fl ame sources, such as lighted candles, should be placed on / above the set.
2) To prevent electric shock, do not remove cover. No user serviceable parts inside. Refer servicing to qualifi ed service personnel.
3) Do not remove the earthing pin on the power plug. This apparatus is equipped with a three pin earthing-type power plug. This plug will only fi t an earthing-type power outlet. This is a safety feature. If you are unable to insert the plug into the outlet, contact an electrician.
Do not defeat the purpose of the earthing plug.
4) To prevent electric shock, ensure the earthing pin on the AC cord power plug is securely connected.
CAUTION
This appliance is intended for use in environments which are relatively free of electromagnetic fi elds. Using this appliance near sources of strong electromagnetic fi elds or where electrical noise may overlap with the input signals could cause the picture and sound to wobble or cause interference such as noise to appear. To avoid the possibility of harm to this appliance, keep it away from sources of strong electromagnetic fi elds.
FOR YOUR SAFETY, PLEASE READ THE FOLLOWING TEXT CAREFULLY.
This display is supplied with a moulded three pin mains plug for your safety and convenience. A 10 amp fuse is tted in this plug. Shall the fuse need to be replaced, please ensure that the replacement fuse has a rating of 10 amps and that it is approved by ASTA or BSI to BS1362.
Check for the ASTA mark
If the plug contains a removable fuse cover, you must ensure that it is refi tted when the fuse is replaced. If you lose the fuse cover the plug must not be used until a replacement cover is obtained. A replacement fuse cover can be purchased from your local Panasonic dealer.
Do not cut off the mains plug. Do not use any other type of mains lead except the one supplied with this display. The supplied mains lead and moulded plug are designed to be used with this display to avoid interference and for your safety. If the socket outlet in your home is not suitable, get it changed by a qualifi ed electrician. If the plug or mains lead becomes damaged, purchase a replacement from an authorized dealer.
WARNING : — THIS DISPLAY MUST BE EARTHED.
How to replace the fuse.
Trademark Credits
• VGA is a trademark of International Business Machines Corporation.
• Macintosh is a registered trademark of Apple Inc., USA.
• SVGA, XGA, SXGA and UXGA are registered trademarks of the Video Electronics Standard Association.
• HDMI, the HDMI Logo, and High-Defi nition Multimedia Interface are trademarks or registered trademarks of HDMI
IMPORTANT: THE MOULDED PLUG
or the BSI mark on the body of the fuse.
ASA
Open the fuse compartment with a screwdriver and replace the fuse.
Even if no special notation has been made of company or product trademarks, these trademarks have been fully respected.
Licensing LLC in the United States and other countries.
Note:
Do not allow a still picture to be displayed for an extended period, as this can cause a permanent image retention to remain on the Plasma Display. Examples of still pictures include logos, video games, computer images, teletext and images displayed in 4:3 mode.
3
Safety Precautions
WARNING
Setup
This Plasma Display is for use only with the following optional accessories. Use with any other type of optional accessories may cause instability which could result in the possibility of injury.
(All of the following accessories are manufactured by Panasonic Corporation.)
• Speakers ........................................................................ TY-SP65P11WK
• Pedestal ......................................................................... TY-ST65VX300
• Wall-hanging bracket (angled) ....................................... TY-WK65PR20
• BNC Dual Video Terminal Board .................................... TY-FB9BD
• HD-SDI Terminal Board .................................................. TY-FB9HD
• HD-SDI Terminal Board with audio ................................ TY-FB10HD
• Dual Link HD-SDI Terminal Board .................................. TY-FB11DHD
• Dual HD-SDI Terminal Board for 3D .............................. TY-FB30DHD3D
• Dual HDMI Terminal Board ............................................ TY-FB10HMD
• DVI-D Terminal Board .................................................... TY-FB11DD
• Dual DVI-D Terminal Board for 3D ................................. TY-FB30DD3D
• AV Terminal Box ............................................................. TY-TB10AV
• 3D IR TRANSMITTER ................................................... TY-3D30TRW
Always be sure to ask a qualifi ed technician to carry out set-up.
Small parts can present choking hazard if accidentally swallowed. Keep small parts away from young children. Discard unneeded small parts and other objects, including packaging materials and plastic bags/sheets to prevent them from being played with by young children, creating the potential risk of suffocation.
Do not place the Plasma Display on sloped or unstable surfaces, and ensure that the Plasma Display does not hang over the edge of the base.
• The Plasma Display may fall off or tip over.
Do not place any objects on top of the Plasma Display.
• If water is spills onto the Plasma Display or foreign objects get inside it, a short-circuit may occur which could result in fi re or electric shock. If any foreign objects get inside the Plasma Display, please consult your local Panasonic dealer.
Transport only in upright position!
• Transporting the unit with its display panel facing upright or downward may cause damage to the internal circuitry.
Ventilation should not be impeded by covering the ventilation openings with items such as newspapers, table cloths and curtains.
For suffi cient ventilation; If using the pedestal (optional accessory), leave a space of 10 cm or more at the top, left and right, and 7 cm or more at the rear, and also keep the space between the bottom of the display and the fl oor surface. If using some other setting-up method, follow the manual of it. (If there is no specifi c indication of installation dimension in the installation manual, leave a space of 10 cm or more at the top, bottom, left and right, and 7 cm or more at the rear.)
4
Safety Precautions
When using the Plasma Display
The Plasma Display is designed to operate on 220 - 240 V AC, 50/60 Hz.
Do not cover the ventilation holes.
• Doing so may cause the Plasma Display to overheat, which can cause fi re or damage to the Plasma Display.
Do not stick any foreign objects into the Plasma Display.
• Do not insert any metal or fl ammable objects into the ventilations holes or drop them onto the Plasma Display, as doing so can cause fi re or electric shock.
Do not remove the cover or modify it in any way.
• High voltages which can cause severe electric shocks are present inside the Plasma Display. For any inspection, adjustment and repair work, please contact your local Panasonic dealer.
Ensure that the mains plug is easily accessible.
An apparatus with CLASS I construction shall be connected to a mains socket outlet with a protective earthing connection.
Do not use any power supply cord other than that provided with this unit.
• Doing so may cause fi re or electric shocks.
Securely insert the power supply plug as far as it will go.
• If the plug is not fully inserted, heat may be generated which could cause fi re. If the plug is damaged or the wall socket is loose, they shall not be used.
Do not handle the power supply plug with wet hands.
• Doing so may cause electric shocks.
Do not do anything that may damage the power cable. When disconnecting the power cable, pull on the plug body, not the cable.
• Do not damage the cable, make any modifi cations to it, place heavy objects on top of it, heat it, place it near any hot objects, twist it, bend it excessively or pull it. To do so may cause fi re and electric shock. If the power cable is damaged, have it repaired at your local Panasonic dealer.
If the Plasma Display is not going to be used for any prolonged length of time, unplug the power supply plug from the wall outlet.
To prevent the spread of fi re, keep candles or other open fl ames away from this product at all times.
If problems occur during use
If a problem occurs (such as no picture or no sound), or if smoke or an abnormal odour starts to come out from the Plasma Display, immediately unplug the power supply plug from the wall outlet.
• If you continue to use the Plasma Display in this condition, fi re or electric shock could result. After checking that the smoke has stopped, contact your local Panasonic dealer so that the necessary repairs can be made. Repairing the Plasma Display yourself is extremely dangerous, and shall never be done.
If water or foreign objects get inside the Plasma Display, if the Plasma Display is dropped, or if the cabinet becomes damages, disconnect the power supply plug immediately.
A short circuit may occur, which could cause fi re. Contact your local Panasonic dealer for any repairs that need to be made.
5
Safety Precautions
CAUTION
When using the Plasma Display
Do not bring your hands, face or objects close to the ventilation holes of the Plasma Display.
• Heated air comes out from the ventilation holes at the top of Plasma Display will be hot. Do not bring your hands or face, or objects which cannot withstand heat, close to this port, otherwise burns or deformation could result.
Be sure to disconnect all cables before moving the Plasma Display.
• If the Plasma Display is moved while some of the cables are still connected, the cables may become damaged, and fi re or electric shock could result.
Disconnect the power supply plug from the wall socket as a safety precaution before carrying out any cleaning.
• Electric shocks can result if this is not done.
Clean the power cable regularly to prevent it becoming dusty.
• If dust built up on the power cord plug, the resultant humidity can damage the insulation, which could result in fi re. Pull the power cord plug out from the wall outlet and wipe the mains lead with a dry cloth.
Do not burn or breakup batteries.
• Batteries must not be exposed to excessive heat such as sunshine, fi re or the like.
This Plasma Display radiates infrared rays, therefore it may affect other infrared communication equipment. Install your infrared sensor in a place away from direct or refl ected light from your Plasma Display.
Cleaning and maintenance
The front of the display panel has been specially treated. Wipe the panel surface gently using only a cleaning cloth or a soft, lint-free cloth.
• If the surface is particularly dirty, wipe with a soft, lint-free cloth which has been soaked in pure water or water in which neutral detergent has been diluted 100 times, and then wipe it evenly with a dry cloth of the same type until the surface is dry.
• Do not scratch or hit the surface of the panel with fi ngernails or other hard objects, otherwise the surface may become damaged. Furthermore, avoid contact with volatile substances such as insect sprays, solvents and thinner, otherwise the quality of the surface may be adversely affected.
If the cabinet becomes dirty, wipe it with a soft, dry cloth.
• If the cabinet is particularly dirty, soak the cloth in water to which a small amount of neutral detergent has been added and then wring the cloth dry. Use this cloth to wipe the cabinet, and then wipe it dry with a dry cloth.
• Do not allow any detergent to come into direct contact with the surface of the Plasma Display. If water droplets get inside the unit, operating problems may result.
• Avoid contact with volatile substances such as insect sprays, solvents and thinner, otherwise the quality of the cabinet surface may be adversely affected or the coating may peel off. Furthermore, do not leave it for long periods in contact with articles made from rubber or PVC.
6
3D Safety Precautions
Safety Precautions
WARNING
Small Parts
3D Eyewear contains small parts (battery and specialised band, etc.) and must be kept out of reach of small children to avoid accidental ingestion.
Disassembly
Do not disassemble or modify the 3D Eyewear.
Lithium Battery
Batteries must not be exposed to excessive heat such as sunshine, fi re or the like.
CAUTION
To enjoy 3D images safely and comfortably, please read these instructions fully.
Use for commercial applications and public viewing
Someone in authority should responsibly convey the precautions for use of the 3D Eyewear to the user.
3D Eyewear
Do not drop, exert pressure on, or step on the 3D Eyewear.
Always store the 3D Eyewear in the case provided when not in use.
Be careful of the tips of the frame when putting on the 3D Eyewear.
Be careful not to trap a fi nger in the hinge section of the 3D Eyewear.
Pay special attention when children are using the 3D Eyewear. 3D Eyewear should not be used by children younger than 5 - 6 years old, as a guideline. All children must be fully supervised by parents or guardians who must ensure their safety and health throughout the using 3D Eyewear.
7
Safety Precautions
Viewing 3D Content
Content for 3D viewing includes commercially available Blu-ray discs, 3D broadcasts, etc. When preparing your own 3D content, ensure that it is properly produced.
Do not use the 3D Eyewear if you have a history of over-sensitivity to light, heart problems, or have any other existing medical conditions.
Please stop using the 3D Eyewear immediately, if you feel tired, are not feeling well or experience any other uncomfortable sensation.
Take an appropriate break after viewing a 3D movie. Take a break of between 30 - 60 minutes after viewing 3D content on interactive devices such as 3D games
or computers. Be careful not to strike the screen or other people unintentionally. When using the 3D Eyewear the distance
between the user and screen can be misjudged. The 3D Eyewear must only be worn when viewing 3D content. If you do not look toward the screen for a while when viewing 3D images, the 3D Eyewear may be turned off
automatically. If you suffer from any eyesight problems (short / far-sighted, astigmatism, eyesight differences in left and
right), please ensure to correct your vision before using the 3D Eyewear. Stop using the 3D Eyewear if you can clearly see double images when viewing 3D content. When the multiple plasma displays are placed side by side, 3D images may be seen doubly due to interference
among them. Place each display at an appropriate location to avoid it. Do not use the 3D Eyewear at a distance less than the recommended distance.
View from at least the recommended distance (3 times the effective height of the screen). Recommended distance TH-65VX300ER: 2.4 m When the top and bottom area of the screen is blackened, such as movies, view the screen at a distance 3 times further than the height of the actual image. (That makes the distance closer than above recommended gure.)
3D Eyewear Use
Before using the 3D Eyewear, ensure no breakable objects surrounding the user to avoid any accidental damage or injury.
Remove the 3D Eyewear before moving around to avoid falling or accidental injury. Always put the 3D Eyewear in the case (supplied) after use. Use the 3D Eyewear only for the intended purpose and nothing else. Do not use 3D Eyewear in the condition of high temperature. Do not use if the 3D Eyewear is physically damaged. Do not use any devices that emit the infrared signals near the 3D Eyewear, as this may cause the 3D Eyewear
false operations. Do not use devices (such as mobile phones or personal transceivers) that emit strong electromagnetic waves
near the 3D Eyewear as this may cause the 3D Eyewear to malfunction. Stop using the 3D Eyewear immediately if a malfunction or fault occurs. Stop using the 3D Eyewear immediately if you experience any redness, pain, or skin irritation around the nose
or temples. In rare cases, the materials used in the 3D Eyewear may cause an allergic reaction.
Lithium Battery
Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.
8
Accessories
Accessories Supply
Check that you have the accessories and items shown
Operating Instruction book
Power supply cord Clamper × 1
CD-ROM (Operating instructions)
TMME289
Remote Control Batteries
Remote Control Transmitter N2QAYB000688
Batteries for the Remote Control Transmitter (R6 (UM3) Size × 2)
Ferrite core × 2 J0KG00000014
Use the Ferrite cores to comply with the EMC standard. (see page 64)
Requires two R6 batteries.
1. Pull and hold the hook, then open the battery cover.
Hook
2. Insert batteries - note correct polarity ( + and -).
Close
Open
“R6 (UM3)” size
Helpful Hint:
For frequent remote control users, replace old batteries with Alkaline batteries for longer life.
Precaution on battery use
Incorrect installation can cause battery leakage and corrosion that will damage the remote control transmitter. Disposal of batteries should be in an environment-friendly manner.
Observe the following precaution:
1. Batteries shall always be replaced as a pair. Always use new batteries when replacing the old set.
2. Do not combine a used battery with a new one.
3. Do not mix battery types (example: “Zinc Carbon” with “Alkaline”).
4. Do not attempt to charge, short-circuit, disassemble, heat or burn used batteries.
5.
Battery replacement is necessary when remote control acts sporadically or stops operating the Plasma Display set.
6. Do not burn or breakup batteries. Batteries must not be exposed to excessive heat such as sunshine, fi re or the like.
9
Connections
Speaker connection
When connecting the speakers, be sure to use only the optional accessory speakers. Refer to the speaker’s Installation Manual for details on speaker installation.
Speakers (Optional accessories)
1
Red
Black
While pressing the lever, insert the core wire.
2
Red
Black
Return the lever.
AC cord connection and fi xing, cable fi xing
AC cord fi xing
Unplug the AC cord
Plug the AC cord into the display unit.
Plug the AC cord until it clicks.
Note:
Make sure that the AC cord is locked on
Using the clamper
Secure any excess cables with clamper as required.
Note:
One clamper is supplied with this unit. In case of securing cables at three positions, please purchase it separately.
both the left and right sides.
Unplug the AC cord pressing the two knobs.
Note:
When disconnecting the AC cord, be absolutely sure to disconnect the AC cord plug at the socket outlet fi rst.
10
Attach the clamper
1
Insert the clamper in a hole.
hole
To remove from the unit:
snaps
Keep pushing both side snaps
Bundle the cables
2
hooks
Set the tip in the hooks
To loosen:
knob
Keep pushing the knob
Video equipment connection
SLOT: Terminal board (optional
accessories) insert slot
(see page 4)
Note:
The right side slot is for factory use only. The terminal board with 1-slot width does not function when installed in the right side slot.
Connections
3D IR TRANSMITTER:
Connect the 3D IR TRANSMITTER (optional accessory).
LAN: Connect to a
network to control the unit. (see page
60)
COMPONENT/RGB IN: Component/RGB Video Input
Terminal (see page 12) AV IN (HDMI): HDMI Input Terminal (see page 12) Connect to video equipment such as VCR or DVD player.
SERIAL:
Control the Plasma Display by connecting to PC. (see page 14)
Terminals are on the bottom side of the Plasma Display.
PC IN:
PC Input Terminal Connect to video terminal of PC or equipment with Y, P
B(CB
) and PR(CR) output
(see page 13).
11
Connections
COMPONENT / RGB IN connection
Note:
Additional equipment, cables and adapter plugs shown are not supplied with this set.
Notes:
• Change the “Component/RGB-in select” setting in the “Setup” menu to “Component” (when Component signal connection) or “RGB” (when RGB signal connection). (see page 41)
• Signals input to COMPONENT/RGB IN terminals correspond to Sync on G or Sync on Y.
Y
P B
P
L
R
R
AUDIO
OUT
, Y , P B , P R
OUT
Computer
DVD Player
RGB Camcorder
HDMI connection
[Pin assignments and signal names]
Pin No.
Signal name
1
T.M.D.S Data2+
T.M.D.S Data2
2
Shield
3
T.M.D.S Data2-
4
T.M.D.S Data1+ T.M.D.S Data1
5
Shield
6
T.M.D.S Data1-
7
T.M.D.S Data0+ T.M.D.S Data0
8
Shield
9
T.M.D.S Data0-
10
T.M.D.S Clock+
Pin No.
13
14
15 16
17
18 19
Note:
Additional equipment and HDMI cable shown are not supplied with this set.
Signal name
T.M.D.S Clock
11
Shield
12
T.M.D.S Clock-
CEC
Reserved (N.C. on device)
SCL SDA DDC/CEC
Ground +5V Power Hot Plug Detect
1
19
18
3
2
4
HDMI cable
HDMI
HDMI
AV OU T
AV OU T
DVD player DVD player
12
PC Input Terminals connection
Connections
Shared with DVI-D IN.
COMPUTER
Connect a cable which matches the audio output terminal on the computer.
Conversion adapter (if necessary)
Audio
(Female)
Stereo mini plug (M3)
Mini D-sub 15p
RGB
PC cable
(Male)
Notes:
• With regard to the typical PC input signals that are described in the applicable input signals list (see page 71), adjustment values such as for the standard picture positions and sizes have already been stored in this unit. You can add up to eight PC input signal types that are not included in the list.
• Computer signals which can be input are those with a horizontal scanning frequency of 15 to 110 kHz and vertical scanning frequency of 48 to 120 Hz. (However, the image will not be displayed properly if the signals exceed 1,200 lines.)
• The display resolution is a maximum of 1,440 × 1,080 dots when the aspect mode is set to “4:3”, and 1,920 × 1,080 dots when the aspect mode is set to “16:9”. If the display resolution exceeds these maximums, it may not be possible to show fi ne detail with suffi cient clarity.
• The PC input terminals are DDC2B-compatible. If the computer being connected is not DDC2B-compatible, you will need to make setting changes to the computer at the time of connection.
• Some PC models cannot be connected to the set.
• There is no need to use an adapter for computers with DOS/V compatible Mini D-sub 15P terminal.
• The computer shown in the illustration is for example purposes only.
• Additional equipment and cables shown are not supplied with this set.
• Do not set the horizontal and vertical scanning frequencies for PC signals which are above or below the specifi ed frequency range.
• Component Input is possible with the pin 1, 2, 3 of the Mini D-sub 15P Connector.
• To use sync input VBS signals, use the connector which incorporates a 75-ohm termination resistance and which is available on the market, for the connection of the HD connector where the VBS signals are to be input.
• Change the “Component/RGB-in select” setting in the “Setup” menu to “Component”
(when Component signal connection) or “RGB” (when RGB signal connection). (see page 41)
Signal Names for Mini D-sub 15P Connector
Pin No. Signal Name Pin No. Signal Name Pin No. Signal Name
1
3
4 5
2
9
10
15 14 13 12 11
1
2
6 7 8
3
4
5
R (PR/CR)
G (Y)
B (PB/CB)
NC (not connected)
GND (Ground)
Pin Layout for PC Input Terminal
6
7
8
9
10
GND (Ground)
GND (Ground)
GND (Ground)
+5 V DC
GND (Ground)
11
NC (not connected)
12
13
14
15
HD/SYNC
SDA
VD
SCL
13
Connections
SERIAL Terminals connection
The SERIAL terminal is used when the Plasma Display is controlled by a computer. Note: To use serial control for this unit, make sure to set the “Control I/F Select” in the “Network Setup” menu to
“RS-232C”. (see page 59)
COMPUTER
(Male)
6789
13452
RS-232C Straight cable
(Female)
D-sub 9p
Notes:
• Use the RS-232C straight cable to connect the computer to the Plasma Display.
• The computer shown is for example purposes only.
• Additional equipment and cables shown are not supplied with this set.
The SERIAL terminal conforms to the RS-232C interface specifi cation, so that the Plasma Display can be controlled by a computer which is connected to this terminal. The computer will require software which allows the sending and receiving of control data which satisfies the conditions given below. Use a computer application such as programming language software. Refer to the documentation for the computer application for details.
Communication parameters
Signal level RS-232C compliant
Synchronization method Asynchronous
Baud rate 9600 bps
Parity None
Character length 8 bits
Stop bit 1 bit
Flow control -
Basic format for control data
The transmission of control data from the computer starts with a STX signal, followed by the command, the parameters, and lastly an ETX signal in that order. If there are no parameters, then the parameter signal does not need to be sent.
STX C1 C2 C3 P1 P2 P3 P4: P5 ETX
Start (02h)
Colon Parameter(s) 3-character command (3 bytes)
(1 - 5 bytes)
End (03h)
Notes:
• If multiple commands are transmitted, be sure to wait for the response for the fi rst command to come from this unit before sending the next command.
• If an incorrect command is sent by mistake, this unit will send an “ER401” command back to the computer.
• S1A and S1B of Command IMS are available only when a dual input terminal board is attached.
• Consult your local Panasonic dealer for detail
Signal names for D-sub 9P connector
Pin No. Details
2 3 5
4
6
• 7 8
1
9
These signal names are those of computer specifi cations.
Command
Command Parameter Control details PON None Power ON POF None Power OFF AVL ** Volume 00 - 63
AMT
IMS None
DAM None
0 Audio MUTE OFF 1 Audio MUTE ON
SL1 S1A S1B YP1
HM1 HM2 PC1
ZOOM FULL JUST NORM ZOM2 ZOM3 SJST SNOM SFUL 14:9
With the power off, this display responds to PON command only.
instructions on command usage.
Pin layout for SERIAL Terminal
R X D T X D
GND
Non use
(Shorted in this set)
NC
Input select (toggle) SLOT input (SLOT INPUT) SLOT input (SLOT INPUT A) SLOT input (SLOT INPUT B) COMPONENT/RGB IN input (COMPONENT) HDMI1 input (HDMI1) HDMI2 input (HDMI2) PC IN input (PC)
Screen mode select (toggle) Zoom, Zoom1 16:9 Just, Just1 (For Video/SD/HD signal) 4:3, 4:3 (1) Zoom2 (For Video/SD/HD signal) Zoom3 (For Video/SD/HD signal) Just2 (For HD signal) 4:3 (2) (For HD signal) 4:3 Full (For HD signal) 14:9 (For Video/SD/HD signal)
14
INPUT MENU
Power On / Off
Connecting the AC cord plug to the Plasma Display.
Connecting the plug to the Wall Outlet
Notes:
• Main plug types vary between countries. The power plug shown at right may, therefore, not be the type tted to your set.
• When disconnecting the AC cord, be absolutely sure to disconnect the AC cord plug at the socket outlet fi rst.
INPUT MENU OK
Power Indicator
Remote Control Sensor
Press the Power switch on the Plasma Display to turn the set on: Power-On.
Power Indicator: Green
Press the
Power Indicator: Red (standby)
Press the button on the remote control to turn the Plasma Display on.
Power Indicator: Green
Turn the power to the Plasma Display off by pressing the switch on the unit, when the Plasma Display is on or in standby mode.
Note:
During operation of the power management function, the power indicator turns orange in the power off state.
button on the remote control to turn the Plasma Display off.
15
Power On / Off
When fi rst switching on the unit
Following screen will be displayed when the unit is turned on for the fi rst time. Select the items with the remote control. Unit buttons are invalid.
OSD Language
1
Select the language.
2
Set.
Day/Time Setup
1
Select “Day” or “Time”.
2
Setup “Day” or “Time”.
1
Select “Set”.
2
Set.
OSD Language
ENGLISH (US)
Day/Time Setup
Set
Time
Day/Time Setup
Set
Day
PRESENT TIME OF DAY PRESENT TIME OF DAY
English (UK)
Deutsch Français
Italiano
Español
Русский
Time MON 99:99
MONDay
99:99
Time MON 99:99
MON
99:99
99:99Time
99:99
No activity power off
To enable No activity power off, select “Enable”.
1
2
Set.
No activity power off
Display will be turned off when there is no activity for 4 hours.
Enable Disable
If selecting “Enable”, a confi rmation window appears.
Select “Yes” or “No”.
1
2
Set.
No activity power off
Are you sure you want to enable ’No activity power off’ ?
Yes No
Notes:
• Once the items are set, the screens won't be displayed when switching on the unit next time.
• After the setting, the items can be changed in the following menus. OSD Language (see page 44) Day/Time Setup (see page 58) No activity power off (see page 43)
16
Power On / Off
Power ON warning message
The following message may be displayed when turning the unit power ON:
3D Safety Precautions
When 3D images will be viewed by unspecifi ed number of people or used for commercial applications, someone in authority should convey the following precautions. These precautions should be followed in the home as well.
3D Viewing/ 3D Content/ Viewing distance/ 3D Eyewear recommendations
- To enjoy 3D images safely and comfortably, please read the Operating Instructions fully.
Activate 3D Safety Precautions if you deliver 3D images to unspecifi ed audiences for business or other purposes. If “3D Function” in “3D Settings” is set to “On”, a warning message is displayed every time the power is turned ON. (see page 45)
No activity power off Precautions
’No activity power off’ is enabled.
If “No activity power off” in Setup menu is set to “Enable”, a warning message is displayed every time the power is turned ON. (see page 43) These message displays can be set with the following menu: Options menu
3D Safety Precautions (see page 61) Power On Message (see page 61)
17
MENU
ENTER/
INPUT
Selecting the input signal
Press to select the input signal to be played back from the equipment which has been connected to the Plasma Display.
INPUT
COMPONENT
HDMI1 HDMI2 PC
When an optional Terminal Board is installed:
INPUT
SLOT INPUT
COMPONENT HDMI1 HDMI2 PC
Component or RGB input terminal in COMPONENT/RGB IN.*
HDMI input terminals in HDMI 1 to HDMI 2.
PC input terminal in PC IN.
* “COMPONENT” may be displayed as “RGB” depending on the setting of “Component/RGB-in select”. (see page 41)
Input terminal in Terminal Board When a dual input Terminal Board is installed, “SLOT INPUT A” and “SLOT INPUT B” are displayed.
Using dedicated buttons for input selection
Press to select HDMI signal terminals in HDMI 1 or HDMI 2.
Press to select component or RGB signal terminal in COMPONENT/RGB IN.
Press to select PC signal terminal in PC IN.
Press to select Input terminal in Terminal Board. For dual input Terminal Board, you can select either input terminal using A or B button.
Notes:
• Selecting is also possible by pressing the INPUT button on the unit.
• Select to match the signals from the source connected to the component/RGB input terminals. (see page 41)
• Image retention (image lag) may occur on the plasma display panel when a still picture is kept on the panel for an extended period. The function that darkens the screen slightly is activated to prevent image retention (see page 69), but this function is not the perfect solution to image retention.
INPUT MENU
ENTER/
18
Basic Controls
Main Unit
INPUT button (Input signal selection)
(see page 18)
Main Power On / Off Switch
MENU Screen ON / OFF
Each time the MENU button is pressed, the menu screen will switch. (see page 24)
Normal Viewing
Sound Pos./Size
Picture
Setup
INPUT MENU
Power Indicator
The Power Indicator will light.
• Power-OFF .... Indicator not illuminated (The unit will
• Standby ........ Red
• Power-ON ...... Green
• PC Power management (DPMS)
....................... Orange (With PC input signal.
When the menu screen is displayed: “” :
press to move the cursor up
” :
press to move the cursor down
(see page 24)
Remote control sensor
Enter / Aspect
ENTER/
still consume some power as long as the power cord is still inserted into the wall outlet.)
Orange (Depending on the type of the function board installed, when the power is supplied to the slot) Orange (When “CONTROL I/F SELECT” is set to “LAN”. See page
59)
See page 43)
button
(see page 21, 24)
Infrared transmitter for 3D Eyewear Note:
Do not place any objects between the transmitter and 3D Eyewear.
19
Basic Controls
Remote Control Transmitter
Standby (ON / OFF) button
The Plasma Display must fi rst be plugged into the wall outlet and turned on at the power switch (see page 15). Press this button to turn the Plasma Display On, from Standby mode. Press it again to turn the Plasma Display Off to Standby mode.
LIGHT button
The remote control’s buttons illuminate.
AUTO SETUP button
Automatically adjusts the position/ size of the screen. (see page 26)
HDMI buttons
Press to select HDMI 1 or HDMI 2 input. (see page 18)
PICTURE button
(see page 28)
OK button
Press to make selections.
Cursor buttons
EXIT button
Exits from Menu screen.
INPUT button
Press to select input signal sequentially. (see page 18)
RECALL button
Press the “RECALL” button to display the current system status.
Input label
1 2
Aspect mode (see page 21) During 3D images (see page 45) Profi le name (see page 36) NANODRIFT Saver operating (see page 55)
Mode of RGB/MONO Settings (see page 51) Mode of HV Delay (see page 27) 3D Colour Compensation: Off (see page 45)
Off timer
3
The off timer indicator is displayed
only when the off timer has been set.
3D
PC
4:3
Memory name: MEMORY2
NANODRIFT
H Delay
3D Colour Compensation Off
1
2
R Off
PC button
Press to select PC input. (see page 18)
COMPO. button
Press to select Component or RGB input. (see page 18)
SLOT buttons
Press to select SLOT Terminal Board. (see page 18)
MENU button
Displays menu screen. (see page 24)
POS. /SIZE button
(see page 25) RETURN button (see page 24)
Press the RETURN button to return to previous menu screen.
FUNCTION buttons
(see page 57, 62)
VIDEO MENU button
Press to select Picture Mode. (see page 29)
Normal Monitor
Dynamic Cinema
EX.SCALER button
(see page 42)
OFF TIMER button
The Plasma Display can be preset to switch to stand-by after a fi xed period. The setting changes to 30 minutes, 60 minutes, 90 minutes and 0 minutes (off timer cancelled) each time the button is pressed.
30 min 60 min
90 min
0 min
When three minutes remain, “Off timer 3 min” will fl ash. The off timer is cancelled if a power interruption occurs.
Off timer 90 min
3
ASPECT button
Press to adjust the aspect. (see page 21)
Numeric buttons
(see page 36)
MEM. LOAD button
(see page 36)
20
ASPECT Controls
MENU
ENTER/
INPUT
The Plasma Display will allow you to enjoy viewing the picture at its maximum size, including wide screen cinema format picture.
Note:
Be aware that if you put the display in a public place for commercial purposes or a public showing and then use the aspect mode select function to shrink or expand the picture, you may be violating the copyright under copyright law. It is prohibited to show or alter the copyrighted materials of other people for commercial purposes without the prior permission of the copyright holder.
Press repeatedly to move through the aspect options: For details about the aspect mode, please see “List of Aspect Modes” (page 70).
[from the unit]
The aspect mode changes each time the ENTER button is pressed.
For VIDEO (S VIDEO) signal input:
4:3 Zoom1 16:9Zoom2 Zoom3 14:9 Just
For PC signal input: For SD signal input (525 (480) / 60i • 60p, 625 (575) / 50i • 50p):
4:3 Zoom 16:9
4:3 Zoom1 16:9Zoom2 Zoom3 14:9 Just
For HD signal input [1125 (1080) / 60i • 50i • 60p • 50p • 24p • 25p • 30p • 24sF, 1250 (1080) / 50i, 750 (720) / 60p • 50p]:
4:3
4:3 Full Zoom1
14:9Just
16:9
Zoom2
Zoom3
[For 3D images] The aspect is fi xed as “16:9” and you cannot switch.
Notes:
• The aspect mode is memorized separately for each input terminal.
• Do not allow the picture to be displayed in 4:3 mode for an extended period, as this can cause a permanent image retention to remain on the Plasma Display Panel.
All Aspect mode
Set “All Aspect” to “On” in Options menu to enable the extended aspect mode (page 61). When All Aspect mode, the aspect mode of pictures is switched as follows. For details about the aspect mode, please see “List of Aspect Modes”. (page 70)
For VIDEO (S VIDEO) signal input:
4:3 Zoom1 16:9Zoom2 Zoom3 14:9 Just
For PC signal input:
4:3 Zoom 16:9
For SD signal input (525 (480) / 60i
4:3 Zoom1 16:9 JustZoom2 Zoom3 14:9
60p, 625 (575) / 50i
50p):
For HD signal input [1125 (1080) / 60i • 50i • 60p • 50p • 24p • 25p • 30p • 24sF, 1250 (1080) / 50i, 750 (720) / 60p • 50p]:
4:3 Full Zoom1 16:9 Just1Zoom2 Zoom3 14:9 Just2 4:3 (1) 4:3 (2)
21
Viewing 3D images
You can enjoy viewing 3D images with contents or programmes compatible with 3D effect by using the 3D eyewear (optional).
Note:
You need the 3D eyewear (optional) to view the 3D images on this display. For further information, see the instruction manuals of the 3D eyewear.
This display supports “Frame Sequential
*
1:
The 3D format that the images for the left and right eyes are recorded with the high defi nition quality and alternately played back
*
2, *3: See “Table of images that can be seen for each 3D Picture Format and the source image format” on page 23.
*
4: To view “Simultaneous” 3D images, one of the following terminal boards should be installed:
Dual HD-SDI Terminal Board for 3D (TY-FB30DHD3D), Dual DVI-D Terminal Board for 3D (TY-FB30DD3D)
To view the 3D images
To view the contents of the Frame Sequential format (ex. 3D-compatible Blu-ray Disc, etc.) with 3D effect
Connect the 3D-compatible player via an HDMI cable (see page 12) and playback the contents.
• Use fully wired HDMI compliant cable.
• For the settings of the player, read the manual of the player.
• If you use the non 3D-compatible player, the images will be displayed without 3D effect.
To view the contents of 3D formats other than Frame Sequential with 3D effect.
Match the picture format in “3D Picture Format” (see page 45) before viewing.
• You can view “Side by Side” and “Top and Bottom” with 3D effect even if you use the non 3D-compatible player.
• Please consult the suppliers of contents or programmes for availability of this service.
Turn the 3D Eyewear on
• See the instruction manual of 3D eyewear for handling.
Put on the 3D Eyewear Watch the 3D images
*1
”, “Side by Side*2”, “Top and Bottom*3” and “Simultaneous*4” 3D formats.
Notes:
• If the room is lit by uorescent lights and light appears to fl icker when using the 3D Eyewear, switch off the uorescent light. Alternatively, please set “3D Refresh Rate” to “100Hz” or “120Hz” whichever reduces fl icker.
(see page 47)
• 3D content will not be correctly visible if the 3D Eyewear is worn upside down or back-to-front.
• Do not wear the 3D Eyewear when watching anything other than 3D images. Liquid crystal displays (such as computer screens, digital clocks or calculators, etc.) may be diffi cult to see while wearing the 3D Eyewear.
• Do not use the 3D Eyewear as sunglasses.
• 3D effects may be perceived differently depending on the person.
22
Viewing 3D images
Troubleshooting for 3D Eyewear
Symptoms Checks
Cannot see 3D images • Has the 3D Eyewear been switched On?
• Ensure that “3D Function” in “3D Settings” is set to “On”. (see page 45)
• Some 3D image signals may not be automatically recognized as 3D images. Set “3D Picture Format” in “3D Settings” to match the picture format. (see page 45)
• Check that there are no obstacles between the display (or 3D IR TRANSMITTER) and the 3D Eyewear. If the 3D Eyewear stops receiving the infrared signal for about 5 minutes, the 3D Eyewear will be turned off automatically.
• Check the available area to use the 3D Eyewear.
• Depending on the person, the 3D images may be diffi cult to see, or cannot be seen, especially in users that have a different level of eyesight between the left and right eyes. Take the necessary steps (wearing glasses etc.) to correct your eyesight before use.
3D Eyewear is turned off automatically • Check that there are no obstacles between the Display (or 3D IR
TRANSMITTER) and the 3D Eyewear or that the 3D Eyewear is placed inside the coverage area. If the 3D Eyewear stops receiving the infrared signal for about 5 minutes, the 3D Eyewear will be turned off automatically.
There is something wrong with the 3D images Indicator lamp will not light when the 3D glasses are turned ON.
• Switch “Reverse” and “Normal” under “3D Picture Sequence” in “3D Settings” (see page 45).
• The battery may be running low or fl at. Change the battery or charge the 3D glasses.
Table of images that can be seen for each 3D Picture Format and the source image format
If the picture appears to be abnormal, refer to the table below to choose the correct 3D picture format setting.
3D Picture Format
Source image format
Side by side
Top and bottom
Normal format
(2D)
*1
When the source image is not recognized correctly
*2
When “3D Function” is set to “On”, the images will be displayed with 3D effect. When set to “Off”, displayed
without 3D effect.
• Depending on the player or contents, the image may be different from the above illustrations.
Auto Side by Side Top and Bottom Native
1
*
1
*
Normal Normal
Normal
2
*
2
*
Normal
23
Loading...
+ 51 hidden pages