PANASONIC Service manual / Схема, сервісна інструкція Service manual & schematics

Page 1
Service Manual
TOP NEXT
MTNC030312A1
B05
Color Television
CT-2733HF
NA8MS
This simplified service manual is issued to add listed models to the simplified service manual order MTNC020203A1 (CT­27SX12F). Unique settings and parts list are included in this simplified manual.Please file and use this simplified service manualtogether with the simplified service manual order MTNC020203A1 (CT-27SX12F) and the main service manual order No. MTNC010527C1 (CT-27SX11E).
© 2003 Matsushita Electric Corporation of America. All rights reserved. Unauthorized copying and distribution is a violation of law.
Page 2
TOP NEXT
Page 3
4 Receiver feature table
TOP PREVIOUS NEXT
FEATURE/MODEL CT-2733HF CHASSIS GP368 TUNNING SYSTEM GEN III CLOSE CAPTION X V-CHIP X CHANNEL COUNT 181 75 OHM INPUT X REMOTE NOT INCLUDED CRT SUPPLIER SAMSUNG (FLAT) CHASSIS NA8MS COMB FILTER 3 DIG HEC/VEC (X=BOTH) VEC VM X V/A NORM (X=BOTH) V COLOR TEMP X AUTO ON X MTS/SAP/DBX X BUILT-IN AUDIO POWER 7WX2 No. OF SPEAKERS 2 SPEAKER TYPE DOME BASS/BALANCE/TREBLE CONTROL X AI SOUND X (ALWAYS ON) SURROUND/BBE BBE A/V (REAR/FRONT) 3(2/1) S-VHS INPUT (REAR/FRONT) 1/1 COMPONENT INPUT (REAR/FRONT) 1/0 SMART PLUG INTERFACE SMART PLUG (RJ-11) AUDIO LINE OUT STEREO MISC GEN 3 MICRO FOR SPECTRADYNE EPJ/HPJ/MISC HPJ
Page 4
TOP PREVIOUS NEXT
Page 5
6 Clone Box Use
TOP PREVIOUS NEXT
The clone box uploads (LEARN) the settings of one television and downloads (TEACH) them to other televisions. This places the television into Hotel Mode.
NOTE:
The Clone Box is not supplied with the set. It can be purchased separately.
6.1 Setting the“Master” Television
6.2 Uploading Television Settings into the Clone Box (LEARN)
6.3 Downloading Settings into Other Televisions (TEACH)
6.4 Setting Individual Volume Limits
6.4.1 For lower volume
6.4.2 For higher volume
6.5 Testing the Settings in the Clone Box
6.6 Testing the Clone Box Battery
6.7 Resetting the Television to Normal TV Mode
6.8 Setting the Television without a Clone Box
6.8.1 Switching to Hotel Mode (All Models)
6.8.2 Switching to Normal TV Mode
TOP PREVIOUS NEXT
Page 6
6.1 Setting the“Master” Television
TOP PREVIOUS NEXT
The features listed in the HOTEL Mode table must be adjusted before cloning can begin.
1. Turn the television ON.
2. Access the Main Menu by pressing the ACTION button.
3. Access the Set Up menu.
Use the CH and VOL buttons to highlight the Set Up icon, then press the ACTION button
Use the CH buttons to highlight AUTO PROG (Auto Channel Programming), then press
the VOL button to begin programming.
NOTE:
This step is mandatory.
If necessary, use MANUAL PROG (Manual Channel Programming) to delete any
undesired channels.
Press the ACTION button to return to the Main Menu.
4. If necessary, access the Picture menu.
Use the CH and VOL buttons to highlight the Picture icon, then press the ACTION button.
Use the CH buttons to highlight a feature, then press the VOL buttons to adjust them.
Press the ACTION button to return to the Main Menu.
5. If desired, access the CHANNELS menu
Use the CH and VOL buttons to highlight CHANNELS icon, then press the ACTION
button.
Page 7
Highlight MANUAL CAPTION and press VOL →.
Use numeric keypad or Vol buttons to select desired channels. Use the CH buttons to
highlight the character position, then press the VOL buttons to select characters for the channel caption.
Press the ACTION button to return to the Main Menu.
6. If desired, access the SET UP menu to set the Energy Management feature. This feature lets you program the television to turn OFF after a pre-determined period of time from the last keyed-in instruction (pressing any buttons on the TV or onthe remote control) received by the television.
Use the CH and VOL buttons to highlight the Setup icon, then press the ACTION button.
Use the CH buttons to highlight the Energy Management feature.
Press VOL or → button to select OFF or 1 through 15 Hours.
7. Exit the Main Menu by pressing the ACTION button.
8. If necessary, set the maximum volume level.
9. If the hotel has hotel “barker” channel, tune the set to the “barker” channel.
NOTE:
Auto Power On feature setting, Audio settings and Channels menu settings can also be cloned.
TOP PREVIOUS NEXT
Page 8
6.2 Uploading Television Settings into the Clone Box (LEARN)
TOP PREVIOUS NEXT
1. Press the POWER ON button on the clone box.
The LEDs will flash red and green to confirm power is ON.
2. Connect the clone box to the Digital Interface port on the back of the television.
The television must be plugged into an AC outlet but can be either OFF or ON.
3. Hold the ALT button while pressing the LEARN button.
The red LED will flash while the data is uploaded to the box. The green LED will light for
about two (2) seconds when the procedure is complete.
NOTE:
The television is now in HOTEL Mode.
4. Disconnect the clone box from the television and turn it OFF.
NOTE:
Data is not lost even if the battery is removed.
TOP PREVIOUS NEXT
Page 9
6.3 Downloading Settings into Other Televisions (TEACH)
TOP PREVIOUS NEXT
1. Press the POWER ON button on the clone box.
The LEDs will flash red and green to confirm power is ON.
2. Connect the clone box to the Digital Interface port on the back of the television.
The television must be plugged into an AC outlet but can be either OFF or ON.
3. Press the TEACH button.
The green LED will flash while data is downloaded to the television. The green LED will
light for about two (2) seconds when the procedure is complete.
NOTE:
The television is now in HOTEL Mode.
4. Disconnect the clone box from the television and turn it OFF.
5. Repeat steps 1 through 4 to set up other televisions.
TOP PREVIOUS NEXT
Page 10
6.4 Setting Individual Volume Limits
TOP PREVIOUS NEXT
This procedure allows the maximum volume level to be changed on individual televisions.
6.4.1 For lower volume
6.4.2 For higher volume
TOP PREVIOUS NEXT
Page 11
6.4.1 For lower volume
TOP PREVIOUS NEXT
The television must be in HOTEL mode.
1. Turn television ON.
2. Adjust the television volume to desired level.
NOTE:
This will become the new maximum volume level
3. Press the POWER ON button on the clone box.
The LEDs will flash red and green to confirm power is ON.
4. Connect the clone box to the Digital Interface port on the back of the television.
5. Hold the ALT button while pressing the LEARN button on the clone box.
The red LED will flash while the data is uploaded into the box. The green LED will light
for about two (2) seconds when the procedure is complete.
6. Disconnect the clone box from the television and turn it OFF.
7. Reset the volume on the television.
8. Refer to the section entitled Downloading Settings into Other Televisions (TEACH).
TOP PREVIOUS NEXT
Page 12
6.4.2 For higher volume
TOP PREVIOUS NEXT
The television must be in Normal TV mode. Refer to the section entitled Resetting the Television to Normal TV mode.
1. Turn television ON.
2. Adjust the television volume to the minimum setting.
3. Press the POWER ON button on the clone box.
The LEDs will flash red and green to confirm power is ON.
4. Connect the clone box to the Digital Interface port on the back of the television.
5. Adjust the television volume to maximum desired level.
6. Hold the ALT button while pressing the LEARN button on the clone box
The red LED will flash while the data is uploaded into the box. The green LED will light
for about two (2) seconds when the procedure is complete.
If the green LED does not light for about two (2) seconds, retry by holding the ALT button
while pressing the LEARN button.
7. Disconnect the clone box from the television and turn it OFF.
8. Reset the volume on the television.
9. Refer to the section entitled Downloading Settings into Other Televisions (TEACH).
TOP PREVIOUS NEXT
Page 13
6.5 Testing the Settings in the Clone Box
TOP PREVIOUS NEXT
This test compares the clone box settings with the television settings. The television must be in HOTEL mode
1. Press the POWER ON button on the clone box.
The LEDs will flash red and green to confirm power is ON.
2. Connect the clone box to the Digital Interface port on the back of the television.
The television must be plugged into an AC outlet but can be either OFF or ON.
3. Press the TEST button.
The LEDs will flash red and green while the data is compared. The green LED will light
for about two (2) seconds if the settings in the box match the television.
4. Disconnect the clone box from the television and turn it OFF.
TOP PREVIOUS NEXT
Page 14
6.6 Testing the Clone Box Battery
TOP PREVIOUS NEXT
1. Press the POWER ON button on the clone box.
The LEDs will flash red and green to confirm power is ON.
2. Hold the ALT button while pressing the TEST button.
The LEDs will alternately flash red and green while the box is tested.
NOTE:
Replace the 9 volt battery if the LEDs do not flash red and green.
The green LED will light for about two (2) seconds, if battery is charged.
NOTE:
If the green LED does not light for about two (2) seconds at the end of the test, new data must be downloaded into the box.
TOP PREVIOUS NEXT
Page 15
6.7 Resetting the Television to Normal TV Mode
TOP PREVIOUS NEXT
1. Press the POWER ON button on the clone box
The LEDs will flash red and green to confirm power is ON
2. Connect the clone box to the Digital Interface port on the back of the television.
The television must be plugged into an AC outlet but can be either OFF or ON
3. Press the AMS button.
NOTE:
Insert a slender tool about 3/4 inch (paper clip) into the opening.
The green LED will flash while the television is reset to TV mode. The green LED will
light for about two (2) seconds when the procedure is complete.
4. Disconnect the clone box from the television and turn it OFF.
5. Press the ACTION + POWER buttons on the front of the set for 5 seconds to reset the TV to factory default mode. Any programed channel, channel caption and other user defined settings will be lost.
TOP PREVIOUS NEXT
Page 16
6.8 Setting the Television without a Clone Box
TOP PREVIOUS NEXT
6.8.1 Switching to Hotel Mode (All Models)
6.8.2 Switching to Normal TV Mode
TOP PREVIOUS NEXT
Page 17
6.8.1 Switching to Hotel Mode (All Models)
TOP PREVIOUS NEXT
Adjust the features listed in the HOTEL Mode Feature Chart before switching modes.
1. Press the ACTION and the VOL buttons on the front control panel simultaneously.
2. Within a second, press the ACTION and the CH buttons on the front control panel simultaneously.
3. ON will flash in red in the lower corner of the screen, indicating HOTEL Mode.
TOP PREVIOUS NEXT
Page 18
6.8.2 Switching to Normal TV Mode
TOP PREVIOUS NEXT
1. Repeat steps 1 and 2 from the previous section.
2. OFF will flash in red in the lower corner of the screen, indicating Normal TV Mode.
TOP PREVIOUS NEXT
Page 19
Page 20
Page 21
J
I
H
G
F
E
D
C
B
A
1 234 56 7 8
DI-BOARD LEFT-SIDE TNP2AA125 CT-2733H
Page 22
J
I
H
G
F
E
D
C
B
A
1 234 56 7 8
DI-BOARD RIGHT-SIDE TNP2AA125 CT-2733H
Page 23
J
I
H
G
F
E
D
C
B
A
1 234 56 7 8
DI-BOARD TNP2AA125 CT-2733H
Page 24
J
I
H
G
F
E
D
C
B
A
1 234 56 7 8
A-BOARD LEFT-SIDE SER2AH025AG CT-2733H
Page 25
J
I
H
G
F
E
D
C
B
A
1 234 56 7 8
A-BOARD LEFT-MIDDLE-SIDE SER2AH025AG CT-2733H
Page 26
J
I
H
G
F
E
D
C
B
A
1 234 56 7 8
A-BOARD RIGHT-MIDDLE-SIDE SER2AH025AG CT-2733H
Page 27
J
I
H
G
F
E
D
C
B
A
1 234 56 7 8
A-BOARD RIGHT-SIDE SER2AH025AG CT-2733H
Page 28
J
I
H
G
F
E
D
C
B
A
1 234 56 7 8
P-BOARD LEFT-PORTION TNP2AA078AH CT-2733H
Page 29
J
I
H
G
F
E
D
C
B
A
1 234 56 7 8
P-BOARD RIGHT-PORTION TNP2AA078AH CT-2733H
Loading...