Panasonic PV-VM202 User Manual

Digital Video Camcorder

Operating Instructions

Model No.

PV-VM202

Mini

Before attempting to connect, operate or adjust this product, please read these instructions thoroughly. Spanish Quick Use Guide is included.

Guía para rápida consulta en español está incluida.

For USA assistance, please call: 1-800-211-PANA(7262) or send e-mail to : consumerproducts@panasonic.com

For Canadian assistance, please call: 1-800-561-5505 or visit us at www.panasonic.ca

LSQT0511A

Things You Should Know

Date of Purchase

Thank you for choosing Panasonic!

You have purchased one of the most sophisticated and reliable products on the market today. Used properly, we’re sure it will bring you and your family years of enjoyment. Please take time to fill in the information on the right. The serial number is on the tag located on the underside of your Palmcorder. Be sure to retain this manual as your convenient Palmcorder information source.

Dealer Purchased From

Dealer Address

Dealer Phone No.

Model No. PV-VM202

Serial No.

Safety Precautions

WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE.

Your It is recommended that only cassette tapes that have been tested and inspected for use in Palmcorder with the

Palmcorder is designed to record and play back in Standard Play (SP) mode and Long Play (LP) mode.

mark be used.

This symbol warns the user that uninsulated

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL

DO NOT REMOVE COVER (OR BACK)

NO USER-SERVICEABLE PARTS INSIDE

voltage within the unit may have sufficient magnitude to cause electric shock. Therefore, it is dangerous to make any kind of contact with any inside part of this unit.

This symbol alerts the user that important literature concerning the operation and maintenance of this unit has been included. Therefore, it should be read carefully in order to avoid any problems.

The above markings are located on the appliance bottom cover.

Note: This equipment has been tested and found to comply with Part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference when operated in a residential environment. If this equipment does cause interference to radio or television reception, which can be determined by turning the equipment off and on, use the equipment in another location and/or utilize an electrical outlet different from that used by the receiver. If necessary, consult the dealer or an experienced radio/TV technician for help. You may find the booklet, ‘Something About Interference’ available from FCC local regional offices helpful.

FCC Warning:

≥To assure continued FCC compliance, the user must use only the provided shielded interfacing cable with ferrite core when

connecting the digital Palmcorder to computer in accordance with instruction herein. Also, any unauthorized changes or modifications to this equipment could void the user’s authority to operate.

Declaration of Conformity

Model No.: PV-VM202 Trade Name: Panasonic Responsible party: Matsushita Electric Corporation of America Address: One Panasonic Way, Secaucus, New Jersey 07094 Telephone number: 1-800-211-PANA (7262)

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

CAUTION: TO PREVENT FIRE OR SHOCK HAZARD AND ANNOYING INTERFERENCE, USE THE RECOMMENDED

CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT. CAUTION: DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY REPLACED. REPLACE ONLY WITH THE SAME OR

≥Since this product gets hot during use, operate it in well ventilated place; do not install this equipment in a confined space such

as a bookcase or similar unit.

ACCESSORIES ONLY.

EQUIVALENT TYPE.

IMPORTANT SAFETY INSTRUCTIONS

1) Read these instructions.

2) Keep these instructions.

3) Heed all warnings.

4) Follow all instructions.

5) Do not use this apparatus near water.

6) Clean only with dry cloth.

7) Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

9) Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10) Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

11) Only use attachments/accessories specified by the manufacturer.

12) Use only with the cart, stand, tripod, bracket, or the table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

13) Unplug this apparatus during lightning storms or when unused for long periods of time.

14) Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as when the power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

S3125A

Precautions

USE & LOCATION

≥TO AVOID SHOCK HAZARD ... Your Palmcorder and

power supply should not be exposed to rain or moisture. Do not connect the power supply or operate your Palmcorder if it gets wet. Your Palmcorder has been designed for outdoor use, however, it is not designed to sustain direct exposure to water, rain, sleet, snow, sand, dust, or a direct splashing from a pool or even a cup of coffee. This action could permanently damage the internal parts of your Palmcorder. Do not attempt to disassemble this unit. There are no user serviceable parts inside. Unplug your Palmcorder from the power supply before cleaning.

≥DO NOT AIM YOUR PALMCORDER AT THE SUN OR

OTHER BRIGHT OBJECTS

≥DO NOT LEAVE THE PALMCORDER WITH THE EVF

AIMED DIRECTLY AT THE SUN AS THIS MAY CAUSE DAMAGE TO THE INTERNAL PARTS OF THE EVF

≥DO NOT EXPOSE YOUR PALMCORDER TO

EXTENDED HIGH TEMPERATURE ... Such as, in direct

sunlight, inside a closed car, next to a heater, etc... This action could permanently damage the internal parts of your Palmcorder.

≥AVOID SUDDEN CHANGES IN TEMPERATURE ... If the

unit is suddenly moved from a cold place to a warm place, moisture may form on the tape and inside the unit.

≥DO NOT LEAVE YOUR PALMCORDER OR THE POWER

SUPPLY TURNED ON WHEN NOT IN USE.

≥STORAGE OF YOUR PALMCORDER ... Store and handle

your Palmcorder in a manner that will not subject it to unnecessary movement (avoid shaking and striking). Your Palmcorder contains a sensitive pick-up device which could be damaged by improper handling or storage.

CARE

≥TO CLEAN YOUR PALMCORDER ... Do not use strong or

abrasive detergents when cleaning your Palmcorder body.

≥TO PROTECT THE LENS ... Do not touch the surface of

the lens with your hand. Use a commercial Palmcorder lens solution and lens paper when cleaning the lens. Improper cleaning can scratch the lens coating.

≥TO PROTECT THE FINISH OF YOUR PALMCORDER ...

Before handling your Palmcorder, make sure your hands and face are free from any chemical products, such as suntan lotion, as it may damage the finish.

This class B digital apparatus complies with CANADIAN ICES-003.

This Product has fluorescent lamps that contain a small amount of mercury. It also contains lead in some components. Disposal of these materials may be regulated in your community due to environmental considerations. For disposal or recycling information please contact your local authorities, or the Electronics Industries Alliance: <http://www.eiae.org

Contents

Before Using

Standard Accessories ......................................................... 6

Quick Guide......................................................................... 7

To View the Playback Picture.............................................. 7

Controls and Components................................................... 8

Remote Controller............................................................. 10

Power Supply .................................................................... 12

Charging Time and Available Recording Time.................. 12

Attaching the Lens Cap ..................................................... 13

Adjusting the Grip Belt....................................................... 13

Inserting a Cassette .......................................................... 13

Turning on/off the Palmcorder and Selecting Modes ........ 14

Using the Viewfinder ......................................................... 14

Using the LCD Monitor ...................................................... 14

Using the Menu Screen..................................................... 15

List of Menus..................................................................... 16

Setting Date and Time....................................................... 19

Internal Lithium Battery Recharge..................................... 19

LP Mode............................................................................ 19

Audio Recording Mode...................................................... 19

CAMERA Mode

Recording.......................................................................... 20

PhotoShot Recording on the DV Cassette........................ 21

Zoom In/Out Functions...................................................... 21

Digital Zoom Function ....................................................... 22

Digital Electronic Image Stabilizer Function...................... 22

Fade In/Out Functions....................................................... 22

Cinema Function............................................................... 23

Backlight Compensation Function..................................... 23

Recording in Special Situations (Program AE).................. 23

Manual Shutter Speed Adjustment.................................... 24

Manual Iris Adjustment (F Number) .................................. 24

Manual Focus Adjustment................................................. 24

Recording in Natural Colors (White Balance).................... 25

Adjusting White Balance Manually .................................... 25

Digital Effect Functions...................................................... 26

VCR Mode

Playing Back...................................................................... 28

Finding a Scene You Want to Play Back........................... 28

Slow Motion Playback ....................................................... 29

Still Playback/Still Advance Playback................................ 29

Finding the End of a Recording......................................... 29

Index Search Functions..................................................... 30

Playback Zoom Function................................................... 31

Playback Digital Effect Functions...................................... 31

Playing Back on Your TV .................................................. 33

Audio Dubbing................................................................... 33

Special Features

DV Camera Style and SD Camera Style ...........................34

Attaching the Battery Adaptor Unit ....................................34

Attaching the Battery .........................................................34

Using a Memory Card........................................................35

Recording on the Memory Card.........................................35

Using the Video Flash........................................................37

Playing Back Files from the Memory Card ........................39

Copying pictures on a Memory Card to a Cassette ........... 40

Slide Show.........................................................................41

Creating a Title ..................................................................42

Inserting a Title ..................................................................42

Protecting the Files on a Memory Card from Accidental

Erasure (File Lock).........................................................43

Deleting the Files recorded on a Memory Card ................. 43

Formatting a Memory Card................................................44

DPOF Setting.....................................................................44

Copying your DV Cassette to an S-VHS or VHS Cassette

(Dubbing) .......................................................................45

Copying an S-VHS or VHS Cassette to your

DV Cassette...................................................................45

Using your Palmcorder with Digital Video Equipment

(Dubbing) .......................................................................46

Using the Software with a Computer .................................47

ArcSoft Software................................................................48

Using the Supplied USB Connection Kit............................ 49

Installing USB Driver..........................................................49

Connecting Computer and Palmcorder ............................. 49

Using the G726 Decoder ...................................................50

Installing the G726 Decoder ..............................................50

Check if Palmcorder is correctly recognized...................... 51

To disconnect USB cable safely ........................................51

Verifying and updating driver .............................................52

If you no longer need software or driver (uninstall)............55

Notes .................................................................................56

Others

Indications..........................................................................57

Warning/Alarm Indications.................................................59

Notes & Precautions..........................................................60

Cautions for Use................................................................65

Explanation of Terms.........................................................68

Specifications.....................................................................69

Palmcorder Accessory System..........................................70

Palmcorder Accessory Order Form

(For USA Customers)......................................................71

Before Requesting Service (Problems and Solutions)....... 72

Request for Service Notice (USA only).............................. 74

Limited Warranty (For USA Customers) ............................75

Customer Services Directory .............................................76

Limited Warranty (For Canadian Customers) .................... 77

Index ..................................................................................78

Spanish Quick Use Guide/

Guía española para el uso rápido..................................79

PV-DAC12

Before Using

Standard Accessories

Illustrated on the left are accessories packaged with the Palmcorder.

1) AC Adaptor, DC Cable and AC Cable (l 12)

≥Supplies power to the Palmcorder.

CR2025

CGA-D07

VSK0611

N2QAEC000003

VFC3731

VYP8344

CAUTION:

This unit will operate on 110/120/220/240 V AC. An AC plug adaptor may be required for voltages other than 120 V AC. Please contact either a local or foreign electrical parts distributor for assistance in selecting an alternate AC plug. We recommend using the accessory power plug adaptor (VJSS0070) in an area which has special AC outlets.

2) Battery Pack (l 12)

≥Supplies power to the Palmcorder.

3) Battery Adaptor Unit (l 34)

4) Remote Controller and Button-Type Battery (l 10, 11)

5) Lens Cap and Lens Cap Cord (l 13)

6) Lens Hood for MEGA STILL

≥By attaching supplied Lens Hood for MEGA STILL

Recording that blocks direct sunlight in Mega-Pixel Recording, you can record better images. However, Lens Cap cannot be attached when the lens hood is being used.

7) A/V Cable (l 33, 45)

8) SD Memory Card (l 56)

9) CD-ROM:

USB Driver for Panasonic DVC (l 49) G726 Decoder (l 47, 50) ArcSoft Software (l 47, 48)

Microsoft United States and other countries. ≥Macintosh is a registered trademark of Apple Computer, Inc. 2001. ArcSoft,

the ArcSoft logo, ArcSoft PhotoImpression 3.0, ArcSoft PhotoBase 3.0, ArcSoft Panorama Maker 3.0 and ArcSoft PhotoPrinter 2000 Pro are trademarks of ArcSoft, Inc.

≥All product/brand names are trademarks or registered trademarks of the

respective holders.

≥Intel ≥i.LINK and “¥” are trademarks. ≥IBM is a registered trademark of IBM Company. ≥MultiMediaCard is a registered trademark. ≥SD is a trademark.

10) USB Cable (l 49)

and Windows® are registered trademarks of Microsoft in the

Pentium® is a registered trademark.

Pictures Recording (l 35, 67)

Pictures

K2KC4CB00002

LSFT0259

9) 10)

LSFT0489 VFA0366

Quick Guide

CHARGEPOWER

QUICK 100%

Charge the Battery.

≥Connect the AC Cable to the AC Adaptor and plug it into Wall Outlet. ≥Attach the Battery to the AC Adaptor. (This will start the charging

process.)

≥After the [POWER] Lamp has lit up, the [CHARGE] Lamp flashes.

When the [100%] Lamp

≥Since the Battery will not be charged when the DC Cable is connected

to the AC Adaptor, disconnect it.

(l 12)

on the AC Adaptor is lit, charging is finished.

OFF ON

CAMERA

VCR

CARD P. B.

OPEN/EJECT

MODE

POWER

Attach the Charged Battery to the Palmcorder.

Turn the Palmcorder on.

≥Slide the

Insert the Cassette.

≥Slide the [OPEN/EJECT]

Cassette compartment cover completely.

≥Insert the Cassette. ≥Press the [PUSH TO CLOSE] ≥Close the lower compartment Cover.

Switch to [ON]. (The [CAMERA] Lamp lights up.)

(l 14)

(l 13)

lever to the right and pull down to open the

to load the Cassette.

(l 12)

6, 7

CAMERA

VCR

CARD P. B.

OFF ON

POWER

CAMERA

VCR

CARD P. B.

MODE

OFF ON

POWER

BACKLIGHT

CAMERA

STILL

MODE

Start recording.

≥Press the ≥Press the

(l 20)

Button. (Recording starts.)

Button again to pause the recording.

To View the Playback Picture

Switch to the VCR Mode, rewind the tape, and play the tape

(l 28)

back.

≥Set the ≥Press the ≥Press the ≥Press the

Turn the Palmcorder off.

≥Set the 6 Switch to [OFF].

Switch to VCR mode. (The [VCR] Lamp lights up.)

Button. (Rewind the tape.)

Button. (Playback starts.)

Button. (Playback stops.)

(l 14

)

10)

13)

14)

15)

16)

17)

Controls and Components

Palmcorder (DV Camera Style)

BACKLIGHT

CAMERA

STILL

12)

11)

18)

19)

W.B./SHUTTER/IRIS/

MF/VOL/JOG

PUSH

1) Menu Button [MENU] (l 15)

2) Title Button [TITLE] (l 42)

3) Multi-Picture Button [MULTI] (l 27, 32, 40, 42) Picture-in-Picture Button [P-IN-P] (l 27)

4) Backlight Button [BACKLIGHT] (l 23) Play Button [1] (l 28, 39, 41)

5) Still Button [CAMERA STILL] (l 21) Camera Still Button [;] (l 29, 39)

6) Fade Button [FADE] (l 22) Stop Button [∫] (l 28, 39, 41)

7) Forward Search Button [SEARCHi] (l 20)

(l 28)

Fast Forward/Cue Button [5]

8) Reverse Search Button [SEARCHj] (l 20) Rewind/Review Button [6] (l 28) Recording Check Button [S] (l 20)

9) LCD Monitor (l 14)

................................................................................................................................

.....................................................................................................................................................................

................................................................................................................................................................................................................................................................

.....................................

..........................................................................

≥Due to limitations in LCD production technology, there may be some

tiny bright or dark spots on the LCD Monitor screen. However, this is not a malfunction and does not affect the recorded picture.

................................................................................................................................

.....................................................................................................................................................................

.....................................

..........................................................................

10) LCD Monitor Open Button [PUSH OPEN] (l 14)

11) Battery Holder

12) Battery Eject Lever [BATTERY EJECT] (l 12)

13) Speaker

14) Microphone (Built-in, stereo)

15) Lens Hood (l 67)

16) Tally Lamp (l 20)

17) Remote Control Sensor (l 11)

18) PhotoShot Button [PHOTO SHOT] (l 21, 35, 36)

19) Multi-Function Dial [PUSH] (l 15, 19, 24, 25, 28, 29)

20) Viewfinder (l 14, 67)

.........................................................................................................................

≥Due to limitations in LCD production technology, there may be some

tiny bright or dark spots on the Viewfinder screen. However, this is not a malfunction and does not affect the recorded picture.

.........................................................................................................................

21) Recording Start/Stop Button (l 20, 38)

22) Audio-Video Input/Output Jack [A/V IN/OUT] (l 33, 45) Headphone Jack [PHONES] (l 62)

≥Connecting an AV Cable to this Jack activates the Palmcorder’s built-in

speaker, but connecting a headphone, etc. deactivates it.

23) Tape/Card Selector [TAPE/CARD] (l 35)

24) Zoom Lever [W/T] (l 21, 22)

25) Card Slot (l 35)

20)

25)

21)

22)

18)

A/V IN/OUT PHONES

PHOTO SHOT

TAPE

24)

CARD

23)

41)

40)

39)

38)

37)

44)

48)

49)

26)

27)

28)

29) 32)

STILL

MPEG4 VOICE

RESET

OFF ON

CAMERA VCR

CARD P. B.

POWER

ACCESS

CARD EJECT

MODE

31)

CARD MODE

30)

AUTO MANUAL

CAMERA RELEASE

TO PC

46)

47)

33)

34)

FOCUS

45)

42)

S-VIDEO IN/OUT

D.STILL PICTURE

35)

36)

26) Reset Button [RESET] (l 72)

27) Operation Mode Lamps [CAMERA/VCR/CARD P.B.] (l 14, 20, 28, 39)

28) Card Access Lamp [ACCESS] (l 35)

29) Card Mode Selector [STILL/MPEG4/VOICE] (l 36, 38, ,39)

30) Power Off/On Mode Selector Switch [OFF/ON/MODE] (l 14, 28, 39)

31) Card Eject Lever [CARD EJECT] (l 35)

32) Mode Selector Switch [AUTO/MANUAL/FOCUS] (l 20, 23, 24, 25)

33) Camera Release Lever [CAMERA RELEASE] (l 34)

34) USB Jack [TO PC] (l 49)

35) White Balance Sensor (l 68)

36) Lens Cap Installation Hole (l 13)

37) Upper Cassette Compartment Cover (l 13)

38) Cassette Holder (l 13)

39) Lower Cassette Compartment Cover (l 13)

40) Cassette Eject Lever [OPEN/EJECT] (l 13)

41) Eyepiece Corrector Knob (l 14)

42) Tripod Receptacle

≥ Use for mounting the Palmcorder on an optional tripod.

43) Grip Belt (l 13)

44) Lens (LEICA DICOMAR)

≥LEICA is a registered trademark of Leica microsystems IR GmbH and

DICOMAR is a registered trademark of Leica Camera AG.

45) S-Video Input/Output Jack [S-VIDEO IN/OUT] (l 33, 45)

46) Digital Still Picture Terminal [D.STILL PICTURE]

47) DV Terminal (i.LINK) [¥] (l 46)

≥Connect this to the digital video equipment. ≥“i.LINK” is the name of connectors in accordance with IEEE1394-1995.

“¥” is a logo marked on products conforming with the “i.LINK” specifications.

Battery Adaptor Unit (for Use in Digital Still Camera Mode)

43)

48) Sensor

49) Tally Lamp (l 38)

≥This Lamp indicates that it’s in use when recording Moving Picture

(MPEG4) or recording Voice.

50) Video Flash (l 37)

51) Microphone (Built-in, Monaural) (l 38)

52) Audio-Video Output/Phones Selector Switch [AV OUT/PHONES]

≥Set this switch to [AV OUT] when watching on a TV (l 33) or dubbing

(l 33, 45), to [PHONES] when using headphones.

≥If this switch is not set to [PHONES], you may hear some noise. ≥If an AV Cable is connected while [AV OUT] is selected, LCD display

will disappear.

53) Zoom Lever [W/T]

≥This functions in the same manner as the 24) of the DV Camera Style.

54) Audio-Video Output/Phones Jack [AV OUT/PHONES] (l 33, 45, 62)

55) Battery Eject Lever (l 34)

≥It is located behind the battery.

56) Recording Start/Stop Button (l 38)

≥This Button is to record Moving Picture (MPEG4) and Voice.

57) Battery Open Lever [OPEN] (l 34)

58) Grip Belt

≥This functions in the same manner as the 43) of the DV Camera Style.

50)

53)

54)

52)

51)

56)

57)

58)

55)

11)

12)

13)

14)

15)

OSD

COUNTER

MULTI/

P-IN-P

/REW

61 5

STILL ADV

INDEX INDEX

SELECT

STORE

OFF/ON

P.B.DIGITAL

OSD

COUNTER

MULTI/

P-IN-P

/REW

61 5

STILL ADV

INDEX INDEX

SELECT

STORE

OFF/ON

P.B.DIGITAL

TIME

RESET

¥REC

PLAY

PAUSE

;

STOP

∫

VAR.

DATE/

TIME

RESET

¥REC

PLAY

PAUSE

;

STOP

∫

VAR.

SHOT

TITLE

A.DUB

FF/

STILL ADV

PHOTO

SHOT

TITLE

A.DUB

FF/

STILL ADV

sVOL r

ITEM

START/

sVOL r

ITEM

START/

PHOTO

DATE/

STOP

ZOOM

P.B.

ZOOM

STOP

ZOOM

P.B.

ZOOM

SET

10)

16)

17)

18)

19)

Remote Controller

Using the wireless remote controller that is supplied with the Palmcorder, most of the Palmcorder functions can be operated from a distance.

Remote Controller Buttons

1) Date and Time Button [DATE/TIME] (l 59)

2) Indication Output Button [OSD] (l 33)

3) Counter Reset Button [RESET] (l 68)

4) Indication Shift Button [COUNTER] (l 59)

5) Multi-Picture/Picture-in-Picture Button [MULTI/P-IN-P] (l 27, 32, 40, 42)

6) Recording Button [REC] (l 45, 46)

7) Audio Dubbing Button [A.DUB] (l 33)

8) Upward Direction Button [π] (for Playback Zoom Function) (l 31)

9) Left/Right Direction Button [∑, ∏] (for Playback Zoom Function) (l 31)

10) Downward Direction Button [∫] (for Playback Zoom Function) (l 31)

11) Slow Motion/Still Advance Button [E, D] (E : reverse direction, D: normal direction) (l 29)

12) Index Search Button [:, 9] (:: reverse direction, 9: normal direction) (l 30)

13) Selection Button [SELECT] (l 31)

14) Store Button [STORE] (l 31)

15) Off/On Button [OFF/ON] (l 31)

16) Zoom/Volume Button [ZOOM/VOL] (l 21, 22, 28, 31)

17) Variable Speed Search Button [VAR. SEARCH] (l 28)

18) Playback Zoom Button [P.B. ZOOM] (l 31)

19) Speed Selection Button [π, ∫] (for variable speed search function) (l 28)

The following buttons function in the same manner as the corresponding buttons on the Palmcorder.

20) PhotoShot Button [PHOTO SHOT] (l 21, 35)

21) Recording Start/Stop Button [START/STOP] (l 20)

22) Title Button [TITLE] (l 42)

23) Menu Button [MENU] (l 15)

24) Item Set Button [SET] (l 15)

25) Item Select Button [ITEM] (l 15)

26) Fast-forward/Cue Button [5] (l 28)

27) Play Button [1] (l 28, 39)

28) Rewind/Review Button [6] (l 28)

29) Pause Button [;] (l 29, 39)

30) Stop Button [∫] (l 28, 29, 39)

26)

27)

28)

29)

30)

OSD

COUNTER

MULTI/

P-IN-P

/REW

61 5

STILL ADV

INDEX INDEX

SELECT

STORE

OFF/ON

P.B.DIGITAL

TIME

RESET

¥REC

PLAY

PAUSE

;

STOP

∫

VAR.

SHOT

TITLE

A.DUB

FF/

STILL ADV

sVOL r

ITEM

START/

PHOTO

DATE/

STOP

ZOOM

P.B.

ZOOM

SET

20)

21)

22)

23)

24)

25)

ª Inserting a Button-type Battery

Before using the remote controller, insert the supplied button-type battery.

While pressing the Stopper 1, pull out the Battery Holder.

Insert the button-type battery with the imprint (i) facing

upward. Insert the Battery Holder into the Remote Controller.

≥When the button-type battery becomes weak, replace it with a new CR2025

battery. (A battery is normally expected to last about one year. However, it depends on operation frequency.)

≥Be sure to match the poles properly when inserting the battery.

................................................................................................................................

.....................................................................................................................................................................

.....................................

..........................................................................

Warning

Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the equipment manufacturer. Discard used batteries according to manufacturer’s instructions. Risk of fire, explosion and burns. Do not recharge, disassemble, heat above 212° F (100° C) or incinerate. Keep the Button-Type battery out of the reach of children. Never put Button-Type battery in mouth. If swallowed, call your doctor.

................................................................................................................................

.....................................................................................................................................................................

Replace battery with Panasonic PART NO. VSBW0004 (CR2025) only. Use of another battery may present a risk of fire or explosion. Caution: Battery may explode if mistreated. Dispose of used battery promptly. Keep away from children. Do not recharge, disassemble or dispose of in fire.

.....................................

..........................................................................

~~~~~~~~~~~~~~~~~~~~~~~~~

ª Using the Remote Controller 1

Direct the Remote Controller at the Remote Control Sensor on the Palmcorder and press the desired button.

≥Distance from the Palmcorder: Within approximately 15 feet (5 meters)

15˚

START/

PHOTO

DATE/

OSD

TIME

RESET

COUNTER

MULTI/

¥REC

P-IN-P

PLAY

/REW

615

STILL ADV

PAUS E

INDEX INDEX

STOP

SELECT

STORE

OFF/ON

P.B.DIGITAL

STOP

SHOT

TITLE

ZOOM

A.DUB

sVOLr

FF/

STILL ADV

;

∫

VAR.

ITEM

P.B.

ZOOM

SET

≥Angle: Approximately 15 degrees in the vertical and horizontal

directions from the central axis

≥The above operating ranges are for indoor use. Outdoors, or under strong

light, the equipment may not operate properly even within the above ranges.

≥Within 3 feet (1 meter) range, you can also use the Remote Controller on

the side (the LCD Monitor side) of the Palmcorder.

Selecting Remote Controller Modes

When two Palmcorders are used simultaneously, they can be operated individually by selecting different Remote Controller Modes. ≥If the Remote Controller Mode on the Palmcorder and Remote Controller do

not match, [REMOTE] is displayed.

Setting on the Palmcorder:

Set [REMOTE] on the [OTHER FUNCTIONS] Sub-Menu to the desired Remote Controller Mode.

Setting on the Remote Controller:

[VCR1]: Press the [D] Button and [∫] Button simultaneously. [VCR2]: Press the [E] Button and [∫] Button simultaneously. ≥When the battery in the Remote Controller is replaced, the Mode is

automatically reset to [VCR1] Mode.

1 2

Power Supply

ª Using the AC Adaptor

Insert the battery-shaped connector of the DC Cable into the

Battery Holder on the Palmcorder. Connect the DC connector plug to the [DC OUT] Jack on the

AC Adaptor. Connect the AC Adaptor and AC Cable.

≥Before disconnecting the power supply, set the [OFF/ON/MODE] Switch on

the Palmcorder to [OFF].

≥Battery cannot be charged if DC Cable is connected to AC Adaptor.

ª Using the Battery

CHARGEPOWER

QUICK 100%

CAMERA

VCR

CARD P. B.

OFF ON

POWER

MODE

Before use, fully charge the battery.

Attach the Battery to AC Adaptor and charge it.

1111

≥Since the Battery will not be charged when the DC Cable is connected

to the AC Adaptor, disconnect it.

≥After the [POWER] Lamp has lighted, the [CHARGE] Lamp flashes.

When the [100%] Lamp

Attach the charged Battery to the Palmcorder.

2222

on the AC Adaptor is lit, charging is finished.

Disconnecting the Power Source

Set the [OFF/ON/MODE] Switch 2 to [OFF], and the [BATTERY EJECT] Lever to the right

≥When attaching or removing battery, set [OFF/ON/MODE] Switch to

[OFF] and make sure the Operation Mode Lamp is not lit.

≥For other notes, see page 60.

, and then slide the Battery to remove it.

~~~~~~~~~~~~~~~~~~~~~~~~

Charging Time and Available Recording Time

A Charging Time

1 h 10 min.

1 h. (55 min.)

1 h.

1 h 15 min. (1 h 5 min.)

1 h 10 min.

2 h 30 min. (2 h 5 min.)

4 h 30 min.

8 h 15 min. (6 h 45 min.)

CGA-D07

CGR-D08A/1B

CGR-D16A/1B

CGR-D53A/1K

B Maximum Continuous Recording Time

≥“1 h 20 min.” indicates 1 hour and 20 minutes. ≥Battery CGA-D07 is supplied. ≥The hours shown in the table are approximate hours. The numeric

characters in parentheses indicate the recording time when the LCD monitor is used. In actual use, the available recording time may be shorter in some cases.

≥The hours shown in the table are for continuous recording at a temperature

of 68xF (20xC) and humidity of 60 %. If the Battery is charged at a higher or lower temperature, the charging time may be longer.

ATTENTION:

A lithium ion/polymer battery that is recyclable powers the product you have purchased. Please call 1-800-8-BATTERY for information on how to recycle this battery.

Attaching the Lens Cap

To protect the Lens surface, attach the Lens Cap.

Pass the loop of the Lens Cap Cord through the Lens Cap

Installation Hole on the Palmcorder. Pass the opposite side of the Lens Cap Cord through the

cord’s hoop. Pull the Lens Cap to the direction of the arrow.

Attach the Lens Cap.

≥The removed Lens Cap can be hooked onto the Grip Belt 1. (When you

are not recording, be sure to keep the Lens Cap attached to the Lens for protection.)

≥If the supplied Lens Hood for MEGA STILL

attached, the Lens Cap cannot be attached.

Pictures Recording is

~~~~~~~~~~~~~~~~~~~~~~~~~

Adjusting the Grip Belt

Adjust the length of the Grip Belt to the size of your hand.

Pass your hand through the Grip Belt and adjust its length.

Fold back the end of the Grip Belt to securely fasten the

velcro tape closure.

≥The Grip Belt can also be adjusted in SD Camera Style.

~~~~~~~~~~~~~~~~~~~~~~~~~

Inserting a Cassette

When power is supplied to the Palmcorder, the cassette can be taken out without turning the Palmcorder on.

OPEN/EJECT

R E C

SAVE

Slide the [OPEN/EJECT] Lever 1 to the right and pull down

to open the Cassette Compartment. Insert a Cassette.

Close the Cassette Compartment and lock the Cassette

Compartment by pressing the [PUSH TO CLOSE] mark. Close the Lower Cassette Compartment Cover.

≥For other notes, see page 60.

ª Accidental Erasure Prevention

Opening the accidental erasure prevention slider 2 on the cassette (by sliding it in the [SAVE] arrow direction) prevents recording. To enable recording, close the accidental erasure protection slider (by sliding it in the [REC] arrow direction.)

12:30:45PM

OCT 10 2002

Turning on/off the Palmcorder and Selecting Modes

Turn on the power first and then select Modes.

ª How to Turn on the Power 1

CAMERA

VCR

CARD P. B.

1, 2, 3

OFF ON

MODE

Set the [OFF/ON/MODE] Switch to [ON] while pressing the center Button

≥The [CAMERA] Lamp lights up.

ª How to Switch Modes 2

Slide the [OFF/ON/MODE] Switch.

≥With each slide of the Switch, the Mode switches in the order of Camera

Mode, VCR Mode, and Card Playback Mode.

≥The appropriate Mode Lamp lights up.

ª How to Turn off the Power

Set the [OFF/ON/MODE] Switch to [OFF] while pressing the

center Button

~~~~~~~~~~~~~~~~~~~~~~~~

Using the Viewfinder

12:30:45PM OCT 10 2002

OFF ON

MODE

Before using the Viewfinder, adjust the field of view so that the displays inside the viewfinder become clear and easy to read.

Slide the Viewfinder backward to access the Eyepiece

Corrector Knob. Adjust by sliding the Eyepiece Corrector Knob 1.

Using the LCD Monitor

With the LCD Monitor open, you can also record the picture while watching it.

Set the [OFF/ON/MODE] Switch to [ON].

180x 90x

LCD/EVF SET

LCD BRIGHTNESS

LOW||||----HIGH

LCD COLOR LEVEL LOW||||----HIGH

EVF BRIGHTNESS LOW||||----HIGH

PUSH MENU TO RETURN

1111

Press the [PUSH OPEN] Button and, at the same time, bring

2222

out the LCD Monitor about 90x in the direction of the arrow.

≥The Viewfinder goes off.

Adjust the LCD Monitor angle according to the desired

3333

recording angle.

≥The LCD Monitor can rotate a maximum of 180x 2 from the vertical

position to the upward direction and a maximum of 90x downward direction. Forcefully rotating the LCD monitor beyond these ranges will damage the Palmcorder.

Closing the LCD monitor

Push the LCD Monitor until the [PUSH OPEN] Button is securely locked.

ª Adjusting Brightness and Color Level

When [LCD/EVF SET] on the [DISPLAY SETUP] Sub-menu is set to [YES], the following items are displayed:

LCD Brightness [LCD BRIGHTNESS]

Adjusts the brightness of the image on the LCD screen.

LCD Color Level [LCD COLOR LEVEL]

Adjusts the color saturation of the image on the LCD screen.

Brightness of the Viewfinder [EVF BRIGHTNESS]

Adjust the brightness of the image in the Viewfinder.

Press the [PUSH] Dial and select the item you want to adjust.

Rotate the [PUSH] Dial and increase or decrease the number

of the vertical bars on the Bar Indication.

≥The Bar Indication has 8 steps. A larger number of vertical bars

indicates stronger brightness or color saturation.

Increasing the Brightness of the Entire LCD Monitor

Set the [LCD MODE] on the [DISPLAY SETUP] Sub-Menu to [BRIGHT].

≥These adjustments do not affect the recorded images.

≥For other notes, see page 67.

to the

2, 3, 4, 5

W.B./SHUTTER/IRIS/

MF/VOL/JOG

PUSH

CAMERA FUNCTIONS

CAMERA SETUP

DIGITAL EFFECT

CARD SETUP

MULTI-PICTURES

RECORDING SETUP

DISPLAY SETUP

OTHER FUNCTIONS

PUSH MENU TO EXIT

VCR FUNCTIONS

PLAYBACK FUNCTIONS

DIGITAL EFFECT

CARD SETUP

MULTI-PICTURES

RECORDING SETUP

AV IN/OUT SETUP

DISPLAY SETUP

OTHER FUNCTIONS

PUSH MENU TO EXIT

CARD FUNCTIONS

DELETE CARD FILE

CARD EDITING

DISPLAY SETUP

OTHER FUNCTIONS

1 2 3

CAMERA

VCR

CARD P. B.

Using the Menu Screen

To facilitate the selection of a desired function or setting, this Palmcorder displays various function settings on menus.

Press the [MENU] Button.

≥When the [CAMERA] Lamp is on, the Camera Function Menu is

displayed.

≥When the [VCR] Lamp is on, the VCR Function Menu is displayed. ≥When the [CARD P.B.] Lamp is on, the Card Function Menu is

displayed.

Rotate the [PUSH] Dial to select a desired Sub-Menu.

≥Rotate the [PUSH] dial to display the items highlighted.

Press the [PUSH] Dial to display the selected Sub-Menu.

Rotate the [PUSH] Dial to select the item to be set.

Press the [PUSH] Dial to set the selected item to a desired

Mode.

≥With each press of the [PUSH] Dial, the cursor [1] brings up a

subsequent Mode. Menu items that cannot be used in combination with the selected menu items are displayed in dark blue.

≥While a Menu is displayed, you cannot begin to record or play back. Menus

can be displayed during playback but not during recording.

≥The above operations can be carried out using the Remote Controller.

(l 10)

≥To display the Menu, press the [MENU] Button

Controller.

≥To select items on the Menu, press the [ITEM] Button

Remote Controller.

≥To set the mode for the selected items, press the [SET] Button

on the Remote Controller.

To Exit the Menu Screen

Press the [MENU] Button again.

About the Menu Mode Setting

The setting selected on the Menu will be retained even when the Palmcorder is turned off. However, if the Battery or AC Adaptor is disconnected before Turning the Palmcorder off, the selected setting may not be retained.

on the Remote

on the

PUSH MENU TO EXIT

START/

PHOTO

DATE/

TIME

¥REC

PLAY

PAUSE

;

STOP

∫

VAR.

SHOT

TITLE

A.DUB

FF/

STILL ADV

STOP

ZOOM

sVOLr

P.B.

ZOOM

SET

ITEM

OSD

RESET

COUNTER

MULTI/ P-IN-P

/REW

615

STILL ADV

INDEX INDEX

SELECT

STORE

OFF/ON

P.B.DIGITAL

4 6

PROG.AE OFF 5 7

PROGRESSIVE AUTO ON OFF

EIS D.ZOOM

CINEMA

RETURN ---- YES

EFFECT1

EFFECT2 OFF NEGA SEPIA

RETURN ---- YES

PICTURE SIZE PICTURE QUALITY

10)

FINE NORMAL ECONOMY CREATE TITLE

11)

RETURN ---- YES

12)

SCAN MODE

13)

SPEED FAST NORMAL SLOW SWING OFF ON

14)

P-IN-P 1 2 3 4

15)

RETURN ---- YES

16)

17)

REC-SPEED

18)

AUDIO-REC 12bit INDEX 2HOUR DAY

19)

WIND-CUT OFF ON

FLASH

20)

RED EYE REDUCTION

21)

RETURN ---- YES

22)

DATE/TIME

23)

C.DISPLAY LINEAR MEMORY

24)

C.RESET ---- YES DISPLAY ALL PARTIAL OFF

25)

LCD MODE NORMAL BRIGHT LCD/EVF SET

26)

RETURN ---- YES

27)

28)

29)

REMOTE TALLY LED OFF ON

30)

BEEP OFF ON

31)

SHUTTER OFF ON CLOCK-SET

32)

SELF-REC NORMAL MIRROR VOICE POWER SAVE OFF ON

33)

RETURN ---- YES

34)

CAMERA SETUP

N Ω º

OFF ON OFF 25 200 OFF ON

PUSH MENU TO EXIT

DIGITAL EFFECT

OFF MULTI P-IN-P WIPE MIX STROBE MAGICPIX TRAIL MOSAIC MIRROR

MONO SOLARI

PUSH MENU TO EXIT

CARD SETUP

PUSH MENU TO EXIT

MULTI-PICTURES

STROBE MANUAL

PUSH MENU TO EXIT

RECORDING SETUP

SP LP

OFF

PUSH

MENU TO EXIT

DISPLAY SETUP

OFF D/T DATE

T.CODE

PUSH MENU TO EXIT

OTHER FUNCTIONS

VCR1 VCR2 OFF

---- YES

PUSH MENU TO EXIT

1200 900 640 480

---- YES

16bit

ON AUTO

OFF ON

---- YES

List of Menus

The illustrations of the Menus are for explanation purposes only, and they are different from the actual Menus.

Camera Mode Main-Menu [CAMERA FUNCTIONS]

[CAMERA SETUP] Sub-Menu

1) Auto Exposure Mode [PROG.AE] (l 23)

2) Progressive PhotoShot

3) Digital Electronic Image Stabilizer [EIS] (l 22)

4) Digital Zoom [D.ZOOM] (l 22)

5) Cinema-like Format Recording [CINEMA] (l 23)

6) Returning to the Main-Menu [RETURN]

[DIGITAL EFFECT] Sub-Menu

7) Digital Effects 1 [EFFECT1] (l 26)

8) Digital Effects 2 [EFFECT2] (l 26)

[CARD SETUP] Sub-Menu

9) Picture Size [PICTURE SIZE] (l 35)

10) Picture Quality [PICTURE QUALITY] (l 36)

11) Title Creation [CREATE TITLE] (l 42)

[MULTI-PICTURES] Sub-Menu

12) Multi-Picture Mode [SCAN MODE] (l 27)

13) Strobe Multi-Picture Speed [SPEED] (l 27)

14) Swing Mode [SWING] (l 27)

15) Position of Small Picture inside Normal Picture [P-IN-P] (l 27)

[RECORDING SETUP] Sub-Menu

16) Recording Speed Mode [REC-SPEED] (l 19)

17) Audio Recording Mode [AUDIO-REC] (l 19, 33)

18) Index Mode [INDEX] (l 30)

19) Wind Noise Reduction [WIND-CUT] ≥If this function is set to [ON], the sound of wind hitting the microphone

can be reduced for recording.

20) Video Flash [FLASH] (l 37)

21) Red Eye Reduction [RED EYE REDUCTION] (l 37)

[DISPLAY SETUP] Sub-Menu

22) Date and Time Indication [DATE/TIME] (l 59)

23) Counter Display Mode [C.DISPLAY] (l 59)

24) Counter Reset [C.RESET] (l 68) ≥Set the counter value to zero. However, it cannot reset the Time Code.

25) Display Mode [DISPLAY] (l 59)

26) LCD Brightness [LCD MODE] (l 14)

27) LCD and Viewfinder Adjustment [LCD/EVF SET] (l 14)

[OTHER FUNCTIONS] Sub-Menu

28) Remote Controller Mode [REMOTE] (l 11)

29) Recording Lamp [TALLY LED] (l 20)

30) Beep Sound [BEEP] (l 60)

31) Shutter Effect [SHUTTER] (l 21)

32) Date and Time Setting [CLOCK-SET] (l 19)

33) Self-Recording [SELF-REC] (l 20)

34) Voice Power Save [VOICE POWER SAVE] (l 63)

Mode [PROGRESSIVE] (l 21)

10)

11)

12)

13)

14)

15)

16)

17)

18)

PLAYBACK FUNCTIONS

BLANK SEARCH ---- YES RECORD TO CARD ---- YES INDEX PHOTO SCENE AUDIO ST1 ST2 MIX AUDIO OUT

RETURN ---- YES

PUSH MENU TO EXIT

DIGITAL EFFECT

EFFECT OFF ON EFFECT SELECT OFF MULTI WIPE MIX STROBE NEGA SEPIA MONO TRAIL SOLARI MOSAIC MIRROR

RETURN ---- YES

PUSH MENU TO EXIT

PICTURE QUALITY FINE NORMAL ECONOMY CREATE TITLE

RETURN ---- YES

SCAN MODE

SPEED FAST NORMAL SLOW SWING OFF ON

RETURN ---- YES

CARD SETUP

PUSH MENU TO EXIT

MULTI-PICTURES

STROBE MANUAL PHOTO SCENE

PUSH MENU TO EXIT

RECORDING SETUP

REC-SPEED SP LP AUDIO-REC 12bit

RETURN ---- YES

PUSH MENU TO EXIT

AV IN/OUT SETUP

AV JACK

A.DUB INPUT DV OUT

IN/OUT OUT/PHONES

STEREO L R

---- YES

16bit

MIC AV IN

OFF ON

VCR Mode Main-Menu [VCR FUNCTIONS]

[PLAYBACK FUNCTIONS] Sub-Menu

1) Blank Search [BLANK SEARCH] (l 29)

2) Recording to Card [RECORD TO CARD] (l 37)

3) Index Search Mode [INDEX] (l 30)

4) Audio Selector [AUDIO] (l 33)

5) Audio Output Mode [AUDIO OUT] (l 62)

6) Returning to the Main-Menu [RETURN]

[DIGITAL EFFECT] Sub-Menu

7) Digital Effect On/Off [EFFECT] (l 31, 32)

8) Digital Effect Selection [EFFECT SELECT] (l 31, 32)

[CARD SETUP] Sub-Menu

9) Picture Quality [PICTURE QUALITY] (l 36)

10) Title Creation [CREATE TITLE] (l 42)

[MULTI-PICTURES] Sub-Menu

11) Multi-Picture Mode [SCAN MODE] (l 32)

12) Strobe Multi-Picture Speed [SPEED] (l 32)

13) Swing Mode [SWING] (l 32)

[RECORDING SETUP] Sub-Menu

14) Recording Speed Mode [REC-SPEED] (l 19, 45, 46)

15) Audio Recording Mode [AUDIO-REC] (l 19, 33)

[AV IN/OUT SETUP] Sub-Menu

16) AV Jack [AV JACK] (l 33, 45, 62)

17) Audio Dubbing Input [A.DUB INPUT] (l 33)

18) AD Conversion Output [DV OUT] (l 45)

[DISPLAY SETUP] Sub-Menu

19) Camera Data [REC DATA]

≥If you set [REC DATA] to [ON], the settings (shutter speed (l 24), iris

(l 24) and white balance settings (l 25), etc.) used during the

recordings are displayed during playback. [---] appears on the display when there is no data.

≥The settings information may not displayed properly if the camera data

of this Palmcorder are played back on other equipment.

The camera data will not be recorded in the following cases:

≥When the data are recorded from a card to a tape. ≥When recording proceeds with no input signals supplied. ≥When recording involves the use of the S-Video or AV Input Jack. ≥When pictures with no camera data are recorded using the DV

Terminal.

≥When displaying a list of titles.

All of the other items on the [DISPLAY SETUP] Sub-Menu are the same as those on the [DISPLAY SETUP] Sub-Menu of the [CAMERA FUNCTIONS] Main-Menu.

[OTHER FUNCTIONS] Sub-Menu

≥Same as described on page 16.

RETURN ---- YES

PUSH MENU TO EXIT

DISPLAY SETUP

DATE/TIME OFF D/T DATE C.DISPLAY LINEAR MEMORY T.CODE C.RESET ---- YES DISPLAY ALL PARTIAL OFF

REC DATA OFF ON

19)

LCD MODE NORMAL BRIGHT LCD/EVF SET ---- YES RETURN ---- YES

PUSH MENU TO EXIT

OTHER FUNCTIONS

REMOTE VCR1 VCR2 OFF CLOCK-SET ---- YES

RETURN ---- YES

PUSH MENU TO EXIT

DELETE CARD FILE

DELETE FILE

BY SELECTION

DELETE ALL FILES

DELETE TITLE

BY SELECTION

PUSH MENU TO EXIT

CARD EDITING

RECORD TO TAPE ---- YES FILE SEARCH ---- YES FILE LOCK - ---- YES SLIDE SHOW ---- YES DPOF SETTING ---- YES CARD FORMAT ---- YES

RETURN ---- YES

PUSH MENU TO EXIT

DISPLAY SETUP

DATE/TIME OFF D/T DATE C.DISPLAY LINEAR MEMORY T.CODE C.RESET ---- YES DISPLAY ALL PARTIAL OFF LCD MODE NORMAL BRIGHT LCD/EVF SET ---- YES

RETURN ---- YES

PUSH MENU TO EXIT

OTHER FUNCTIONS

REMOTE VCR1 VCR2 OFF CLOCK-SET ---- YES

VOICE POWER SAVE OFF ON

Card Playback Mode Main-Menu [CARD FUNCTIONS]

[DELETE CARD FILE] Sub-Menu

1) Selecting and deleting a File [DELETE FILE BY SELECTION] (l 43)

2) Deleting All Files [DELETE ALL FILES] (l 43)

3) Selecting and Deleting a Title [DELETE TITLE BY SELECTION] (l 43)

[CARD EDITING] Sub-Menu

4) Recording to Cassette [RECORD TO TAPE] (l 40)

5) Searching a File [FILE SEARCH] (l 40)

6) Setting the Lock [FILE LOCK] (l 43)

7) Setting a Slide Show [SLIDE SHOW] (l 41)

8) Setting DPOF [DPOF SETTING] (l 44)

9) Formatting a Card [CARD FORMAT] (l 44)

[DISPLAY SETUP] Sub-Menu

≥Same as described on page 16.

[OTHER FUNCTIONS] Sub-Menu

≥Same as described on page 16.

RETURN ---- YES

PUSH MENU TO EXIT

10)

11)

12)

FILE SEARCH DELETE FILE

13)

FILE LOCK DPOF SETTING

14)

EXIT

Short-Cut Menus of the Card Playback Mode

If you use the Short-Cut Menu, the Card Playback Mode Menu can be called up quickly. Press the [PUSH] Dial to display the Short-Cut Menu, and turn the [PUSH] Dial to select the desired Menu.

10) [FILE SEARCH]: The [FILE SEARCH] Menu for finding files by number appears. (l 40)

11) [DELETE FILE]: The [DELETE FILE] Menu for deleting the file being displayed appears. (l 43) Use this Menu after the file to be erased appears.

12) [FILE LOCK]: The [FILE LOCK] Menu to prevent the accidental erasure of files (Lock Setting) being displayed appears. (l 43) Use this Menu after the file to be locked appears.

13) [DPOF SETTING]: The [DPOF SETTING] Menu for performing the DPOF settings for the displayed picture appears. (l 44) Use this Menu after the picture whose DPOF settings are to be performed has appeared.

14) [EXIT]: For terminating the Short-Cut Menu.

CLOCK SET

YEAR :2002

MONTH :DEC DAY :21 HOUR :12AM MINUTE:15

PUSH MENU TO RETURN

1, 2

W.B./SHUTTER/IRIS/

MF/VOL/JOG

PUSH

1, 3

Setting Date and Time

Press the [MENU] Button and rotate the [PUSH] Dial to select [OTHER FUNCTIONS] >> [CLOCK-SET] >> [YES].

Rotate and press the [PUSH] Dial to select [YEAR]/[MONTH]/[DAY]/[HOUR]/[MINUTE] and set it to a desired value.

≥Year will cycle in the order shown below.

2000, 2001, ..., 2089, 2000, ...

Press the [MENU] Button to finish setting the date and time.

≥The clock operation starts from [00] second. ≥The menu will disappear when the [MENU] button is pressed again.

≥It is possible that the built-in clock in the Palmcorder may become

inaccurate. Please check the time before recording. If the [0] Indication

is flashing, charge the built-in lithium battery and reset the date and

time.

~~~~~~~~~~~~~~~~~~~~~~~~~

Internal Lithium Battery Recharge

The internal lithium battery sustains the operation of the clock. When the [0] Indication

Connect the AC Adaptor to the Palmcorder with the power

turned off and then connect to the AC Jack.

≥After charging for 4 hours, the built-in lithium battery can power the

is lit, the internal lithium battery is near discharge.

clock for approximately 3 months.

CAMERA FUNCTIONS

CAMERA SETUP

DIGITAL EFFECT

CARD SETUP

MULTI-PICTURES

RECORDING SETUP

DISPLAY SETUP

OTHER FUNCTIONS

PUSH MENU TO EXIT

RECORDING SETUP

REC-SPEED

AUDIO-REC 12bit INDEX 2HOUR WIND-CUT OFF FLASH RED EYE REDUCTION

RETURN ---- YES

REC-SPEED

AUDIO-REC

INDEX 2HOUR WIND-CUT OFF FLASH RED EYE REDUCTION

RETURN ---- YES

SP LP

PUSH

MENU TO EXIT

RECORDING SETUP

SP 12bit

PUSH

MENU TO EXIT

ON OFF

16bit

ON OFF

~~~~~~~~~~~~~~~~~~~~~~~~~

LP Mode

A desired recording speed can be selected with [REC-SPEED] on the [RECORDING SETUP] Sub-Menu.

If LP Mode is selected, the recording time becomes 1.5 times longer than that of SP Mode.

Although the image quality does not decrease with the LP Mode recording, mosaic-like noise patterns may appear on a playback image, or some normal functions may be restricted. ≥The contents that are recorded in LP Mode are not completely compatible

with other equipment.

≥Audio Dubbing is not possible with LP Mode. (l 33)

~~~~~~~~~~~~~~~~~~~~~~~~~

Audio Recording Mode

The sound quality of the recorded sound can be selected with [AUDIO-REC] on the [RECORDING SETUP] Sub-Menu. High sound-quality recording is possible with “16bit 48kHz 2 track” Mode. With the “12bit 32kHz 4 track” Mode, the original sound can be recorded on 2 tracks in stereo, while the other 2 tracks can be used for re-recording.

CARD MODE

MODE

AUTO MANUAL

FOCUS

RESET

CAMERA VCR

CARD P. B.

ACCESS

STILL MPEG4 VOICE

OFF ON

POWER

3, 4

TAPE

CARD

REC

RECORD

PAUSE

BACKLIGHT

CAMERA

STILL

7 6

CAMERA Mode

Recording

Set the [OFF/ON/MODE] Switch to [ON].

≥The [CAMERA] Lamp lights up.

Slide the [TAPE/CARD] Selector towards [TAPE].

Press the Recording Start/Stop Button.

≥Recording starts. ≥After the [RECORD] Indicatior is displayed, it changes to [REC]. ≥The Tally Lamp (LED Lamp)

those being recorded that recording is in progress. The Tally Lamp does not light up if the [TALLY LED] on the [OTHER FUNCTIONS] Sub-menu is set to [OFF].

Press the Recording Start/Stop Button again to pause the

recording.

≥[PAUSE] Indication is displayed.

≥If the Recording Pause Mode continues for more than 5 minutes, the power

is turned off automatically for tape protection and power conservation. To resume recording from this condition, turn on the power again.

≥When recording while the Mode Selector Switch is set to [AUTO]

Palmcorder automatically adjusts the focus and white balance. (In some cases, they cannot be adjusted automatically and need to be adjusted manually.) (l 24, 25)

ª To Check the Recording

By pressing the [S] Button 6 in the Recording Pause Mode, you can play back the last few seconds of the recorded scene. ≥[CHK]

is displayed. After checking, the Palmcorder resumes the Recording

Pause Mode.

ª To View the recorded scene while the Recording is

paused

The recorded scene can be viewed by holding down the [SEARCHj] Button

or [SEARCHi] Button 7 in the Recording Pause Mode.

The Camera Search function is useful for finding the starting point of a new scene to create a smooth transition from one scene to another. ≥When the [SEARCHj] Button is pressed, images are played back in the

reverse direction.

≥When the [SEARCHi] Button is pressed, images are played back in the

forward direction.

(Camera Search)

ª Self-Recording

By opening the LCD Monitor and turning it so that it faces forward (to the lens side), you can let the subject in front of the Palmcorder monitor the shot while shooting is in progress. ≥When the LCD Monitor is opened, the Viewfinder is disabled automatically.

However, when the LCD Monitor is rotated forward, the image is also shown in the Viewfinder.

≥If you prefer to have the image on the LCD Monitor to look like an image in

a mirror, set [SELF-REC] on the [OTHER FUNCTIONS] Sub-Menu to [MIRROR]. (Mirror Mode) Images are recorded normally and no left and right reversal occurs.

≥If [MIRROR] is selected, only recording Indication [¥], recording pause

Indication [¥;], Card PhotoShot Indication [ ] and Remaining Battery Power Indication [x] are displayed Indication [°] appears, return the LCD Monitor to the original position in order to check the specific content of the Warning/Alarm Indication.

ª To Finish the Recording

Set the [OFF/ON/MODE] Switch to [OFF].

≥For other notes, see page 60.

lights up during recording and alerts

. If a general Warning/Alarm

, the

BACKLIGHT

CAMERA

STILL

PhotoShot Recording on the DV Cassette

With this function, you can record still pictures with sound for approximately 7 seconds each on the Cassette.

Slide the [TAPE/CARD] Selector to [TAPE].

Press the [PHOTO SHOT] Button in the Recording Pause

Mode.

≥The Palmcorder records a still picture for about 7 seconds and then

switches back to the Recording Pause Mode.

≥PhotoShot Recording results in slightly inferior image quality.

PHOTO

TAPE

CARD

PHOTO

PHOTO SHOT

ª Progressive PhotoShot

With the Progressive PhotoShotTM Mode, you can record still pictures with higher resolution than with the normal PhotoShot Function. ≥After setting [PROGRESSIVE] on the [CAMERA SETUP] Sub-menu to [ON]

or [AUTO], press the [PHOTO SHOT] Button in the Recording Pause Mode. [æ] is displayed.

≥This Function may not work with some function settings. (l 60) ≥If you select Card Mode, [PROGRESSIVE] is set to [ON].

Mode

ª Continuous PhotoShot

If the [PHOTO SHOT] Button is held down with the [SHUTTER] of the Sub-Menu [OTHER FUNCTIONS] set to [ON], the Palmcorder will record still images without interruptions every 0.7 seconds until the button is released. ≥The screen blinks and, at the same time, a shutter clicking sound is

recorded. (This function, however, is not enabled when Progressive PhotoShot is set to [ON] or [AUTO].)

ª Digital Still Picture

When the [CAMERA STILL] Button 2 is pressed, images become still pictures. When the Button is pressed again, the Digital Still Picture Mode is cancelled. ≥We recommend that you press the [CAMERA STILL] Button first at the

position where you want to record the picture and then press the [PHOTO SHOT] Button.

≥For the still pictures taken in the Continuous PhotoShot Mode or Digital Still

Picture Mode, PhotoShot index signals are not recorded.

1t W

5t W

10t W

Zoom In/Out Functions

It gives special effects to the Palmcorder by Recording objects close by or with wide-angle shot.

For wide-angle shots (zoom out):

Press the [W/T] zoom lever towards [W]. For close-ups (zoom in): Press the [W/T] zoom lever towards [T].

≥Zoom magnification is displayed for a few seconds. ≥Generally speaking, when the [W/T] zoom lever is pressed further towards

[W] or [T], the zooming speed gradually increases.

Taking Close-up Shots of Small Subjects (Macro Close-up Function)

When the zoom magnification is 1k, the Palmcorder can focus on a subject that is as close as approximately 1.5 inches (35 mm) from the lens. With this, small subjects such as insects can be recorded.

≥For other notes, see page 60.

~~~~~~~~~~~~~~~~~~~~~~~~~

20t W

D.ZOOM

EIS

W.B./SHUTTER/IRIS/

MF/VOL/JOG

PUSH

W.B./SHUTTER/IRIS/

MF/VOL/JOG

PUSH

Digital Zoom Function

This function is useful when you want to record close-up shots of subjects located beyond a normal zoom range of 1k to 10k magnification. With the Digital Zoom Function, you can select a magnification of 25k or 200k.

Set [CAMERA FUNCTIONS] >> [CAMERA SETUP] >>

[D.ZOOM] >> [25t

≥25k: Digital zooming to 25k ≥200k: Digital zooming to 200k

To zoom in or out, press the [W/T] zoom lever towards [T] or

] or [200

tttt

]

towards [W].

≥As the magnification of digital zooming increases, the quality of image may

deteriorate.

Canceling the Digital Zoom Function

Set [D.ZOOM] on the [CAMERA SETUP] Sub-menu to [OFF].

≥For other notes, see page 60.

~~~~~~~~~~~~~~~~~~~~~~~~

Digital Electronic Image Stabilizer Function

If you are recording in unstable situations and the Palmcorder is shaky, you can use this function to correct for camera shake in these images. ≥If the Palmcorder shakes too much, this Function may not be able to

stabilize images.

Set [CAMERA FUNCTIONS] >> [CAMERA SETUP] >> [EIS] >>

[ON].

≥The [EIS] Indication 1 appears.

Canceling Digital Electronic Image Stabilizer

Set [EIS] on the [CAMERA SETUP] Sub-Menu to [OFF].

EIS function may not work when...

≥Palmcorder movement is too extreme. ≥Recording a subject with distinct horizontal or vertical stripes. ≥Recording in low light situations. ≥Recording a subject under a great amount of fluorescent light. ≥Recording a scene with very fast movement.

1 2

1, 3

≥For other notes, see page 60.

~~~~~~~~~~~~~~~~~~~~~~~~

Fade In/Out Functions

Fade In

Fade In brings out images and sounds gradually from a black screen at the beginning of a scene.

Fade Out

Fade Out causes images and sounds to disappear gradually, leaving a black screen at the end of a scene.

≥Fade in/out function cannot be used in MPEG4 Recording Mode (l 38),

≥For other notes, see page 60.

Hold down the [FADE] Button while the Palmcorder is set to the Recording Pause Mode.

≥The image fades out gradually.

When the image is completely gone, press the Recording Start/Stop Button to start recording. Release the [FADE] Button about 3 seconds after starting recording.

≥The image reappears gradually.

Hold down the [FADE] Button while recording.

≥The image fades out gradually.

About 3 seconds after the image is completely gone, press the recording Start/Stop Button to stop recording. Release the [FADE] Button.

PhotoShot Recording Mode, or Still Picture Mode (l 21).

CINEMA

W.B./SHUTTER/IRIS/

MF/VOL/JOG

PUSH

Cinema Function

This function is for recording in a cinema-like wide screen.

Set [CAMERA FUNCTIONS] >> [CAMERA SETUP] >>

[CINEMA] >> [ON].

≥Black bars appear at the top and bottom of the screen.

To Cancel the Cinema Mode

Set [CAMERA FUNCTIONS] >> [CAMERA SETUP] >> [CINEMA] >> [OFF].

≥For other notes, see page 61.

~~~~~~~~~~~~~~~~~~~~~~~~~

Backlight Compensation Function

This prevents a recording subject from being recorded darker in backlight. (Backlight is the light that shines from behind a recording subject.)

Press the [BACKLIGHT] Button.

≥The [ª] Indication 1 flashes and then is displayed.

To resume normal Recording

Press the Backlight Button [BACKLIGHT].

BACKLIGHT

W.B./SHUTTER/IRIS/

MF/VOL/JOG

PUSH

AUTO MANUAL

FOCUS

≥When the [BACKLIGHT] Button is pressed, the entire screen becomes

brighter.

≥By operating the [OFF/ON/MODE] Switch, the Backlight Compensation

Function is cancelled.

≥This function cannot be used when the Iris is set.

~~~~~~~~~~~~~~~~~~~~~~~~~

Recording in Special Situations

(Program AE)

Select optimal automatic exposures under specific recording situations.

Set the Mode Selector Switch to [MANUAL].

≥The [MNL] Indication appears.

Set [CAMERA FUNCTIONS] >> [CAMERA SETUP] >>

1 2

], [7], [4], [Ω], [º].

[PROG.AE] >> a desired Mode [

≥The Indication of the selected Mode is displayed.

[5] Sports Mode

For Recording scenes involving quick movements, such as sports scenes.

[7] Portrait Mode

Focuses on the main subject of the image and leaves the background slightly out of focus.

[4] Low Light Mode

Preserves the mood of dim light settings without altering picture brightness.

[Ω] Spotlight Mode

Neutralizes the additional brightness created by a spotlight.

[º] Surf & Snow Mode

Compensates for excessive illumination from sun glare to produce a clear picture.

Canceling the Program AE Function

Set [PROG.AE] on the [CAMERA SETUP] Sub-Menu to [OFF]. Or, set the Mode Selector Switch to [AUTO].

≥For other notes, see page 61.

MNL

1/800

MNL

1/60

F2.4

2, 3

W.B./SHUTTER/IRIS/

AUTO MANUAL

1 2

AUTO MANUAL

MF/VOL/JOG

PUSH

FOCUS

2, 3

W.B./SHUTTER/IRIS

MF/VOL/JOG

PUSH

FOCUS

1 2

Manual Shutter Speed Adjustment

Useful for Recording fast-moving subjects

Set the Mode Selector Switch to [MANUAL].

≥The [MNL] Indication 1 appears.

Press the [PUSH] Dial repeatedly until the shutter speed

appears.

Indication Rotate the [PUSH] Dial to adjust the shutter speed.

The Range of Shutter Speed Adjustment

Tape Mode 1/60–1/8000 Card Mode 1/60–1/500 (or 1/30-1/500: for Mega Pixel Recording) The standard shutter speed is 1/60 (or 1/30: for Mega Pixel Recording). Selecting a speed closer to [1/8000] causes the shutter speed to be faster and light level to be lower. ≥When the progressive function is [ON], a speed only up to 1/500 can be

used.

To Resume Automatic Adjustment

Set the Mode Selector Switch to [AUTO].

≥For other notes, see page 61.

~~~~~~~~~~~~~~~~~~~~~~~~

Manual Iris Adjustment

You can use this function when the screen is too bright or too dark.

Set the Mode Selector Switch to [MANUAL].

≥The [MNL] Indication 1 appears.

Press the [PUSH] Dial repeatedly until the iris Indication 2

appears. Rotate the [PUSH] Dial to adjust the iris.

Adjustable Range of the Iris

CLOSE (Closed), F16, ..., F2.0 OP (Opened), i0dB, ..., OPi18dB When a value closer to [CLOSE] is selected, the image becomes darker. When a value closer to [OPi18dB] is selected, the image becomes brighter. The value to which idB is attached indicates a gain value. If this value is too large, the quality of the image deteriorates.

To Resume Automatic Adjustment

Set the Mode Selector Switch to [AUTO].

(F Number)

MNL

≥For other notes, see page 61.

~~~~~~~~~~~~~~~~~~~~~~~~

Manual Focus Adjustment

Focus can be adjusted manually for recording in a situation where auto focus

W.B./SHUTTER/IRIS/

MF/VOL/JOG

PUSH

AUTO MANUAL

FOCUS

1, 2

may not function well.

Set the Mode Selector Switch to [MANUAL].

≥The [MNL] Indication 1 appears.

Slide the Mode Selector Switch to [FOCUS].

≥The [1MF] Indication (Manual Focus Mode) 2 appears.

Rotate the [PUSH] Dial to adjust the focus.

To Resume Automatic Adjustment

Set the Mode Selector Switch to [AUTO].

2, 3

W.B./SHUTTER/IRIS/

MF/VOL/JOG

PUSH

10 000K

9 000K 8 000K

7 000K

6 000K

5 000K

4 000K

3 000K

2 000K

1 000K

10)

1AWB

Recording in Natural Colors

(White Balance)

Depending on the scene or light conditions, the Automatic White Balance

Adjustment Mode may not be able to bring out natural colors. In such a case, the white balance can be adjusted manually.

Set the Mode Selector Switch to [MANUAL].

≥The [MNL] Indication appears.

Press the [PUSH] Dial.

≥The [AWB] Indication appears.

Rotate the [PUSH] Dial to set a desired White Balance Mode.

Automatic White Balance Adjustment [AWB]

Indoor Mode (shooting under incandescent lamp)

Outdoor Mode

Fluorescent light Mode

The White Balance setting that was previously set manually

To Resume Automatic Adjustment

Rotate the [PUSH] Dial until the [AWB] Indication appears. Or, set the Mode Selector Switch to [AUTO].

≥For other notes, see page 61.

2, 3

W.B./SHUTTER/IRIS/

AUTO MANUAL

MF/VOL/JOG

PUSH

FOCUS

~~~~~~~~~~~~~~~~~~~~~~~~~

Adjusting White Balance Manually

When the Auto White Balance Adjustment function does not operate under

AUTO MANUAL

FOCUS

MNL

the existing light conditions, use the Manual White Balance Adjustment mode.

Set the Mode Selector Switch to [MANUAL].

≥The [MNL] Indication 1 appears.

Press the [PUSH] Dial.

≥The [AWB] Indication appears.

Rotate the [PUSH] Dial until the [1] Indication 2 is displayed.

Point the Palmcorder at a full-screen white subject, and then keep the [PUSH] Dial pressed until Indication [

] stops

flashing.

≥When the [1] Indication flashes after turning the Palmcorder on, the

previously adjusted white balance setting is still kept.

To Resume Automatic Adjustment

Rotate [PUSH] Dial until the [AWB] Indication is displayed. Or, set the Mode Selector Switch to [AUTO].

ª About White Balance Sensor

The White Balance Sensor determines the nature of the light source during recording. ≥Do not cover the White Balance Sensor with your hand during recording.

Otherwise, White Balance will not work normally.

Use of Auto White Balance Adjustment in inappropriate lighting conditions may result in reddish or bluish images. Where the subject is found on the left but surrounded by many light-sources, Auto White Balance Adjustment may not operate properly. In such a case, we suggest that you adjust the White Balance.

1) The range that is controlled by the Auto White Balance Adjustment Mode of this Palmcorder

2) Blue sky

3) Cloudy sky (Rain)

4) TV screen

5) Sunlight

6) White fluorescent light

7) Halogen light bulb

8) Incandescent light bulb

9) Sunrise and sunset

10) Candlelight

≥For other notes, see page 61.

1) MULTI 2) P-IN-P

3) WIPE 4) MIX

5) STROBE

6) MAGICPIX 7) TRAIL

8) MOSAIC 9) MIRROR

Digital Effect Functions

This Palmcorder is equipped with digital effect functions that add special effects to the scene.

Digital Effects 1 [EFFECT1]

1) [MULTI] Multi-Picture Mode

2) [P-IN-P] Picture-in-Picture Mode

3) [WIPE] Wipe Mode

4) [MIX] Mix Mode

5) [STROBE] Strobe Mode

≥Records images with a stroboscopic effect.

6) [MAGICPIX] Gain-up Mode

≥Brightens images electronically. ≥Adjust focus manually when using this Mode.

7) [TRAIL] Trailing Effect Mode

≥Records images with a trailing effect.

8) [MOSAIC] Mosaic Mode

≥Produces a mosaic-like image.

9) [MIRROR] Mirror Mode

≥The right half of an image becomes a mirror image of the left half.

Digital Effects 2 [EFFECT2]

10) [NEGA] Negative Mode

≥The colors of the recorded image are inverted as seen in a negative.

11) [SEPIA] Sepia Mode

≥Records a scene with a brownish tint, like the color of old pictures.

12) [MONO] Black & White Mode

≥Records an image in black and white.

13) [SOLARI] Solarization Mode

≥Records an image with a painting-like effect.

10) NEGA 11) SEPIA

12) MONO 13) SOLARI

MIX

WIPE

W.B./SHUTTER/IRIS/

MF/VOL/JOG

PUSH

2, 3, 4

WIPE

Selecting a desired digital effect

Set [CAMERA FUNCTIONS] >> [DIGITAL EFFECT] >> [EFFECT1] or [EFFECT2] >> a desired digital effect.

Canceling the digital effect

Set [CAMERA FUNCTIONS] >> [DIGITAL EFFECT] >> [EFFECT1] or [EFFECT2] >>[OFF].

≥For other notes, see page 61.

~~~~~~~~~~~~~~~~~~~~~~~~

ª Wipe Mode and Mix Mode

Wipe Mode:

Like a curtain is being pulled, the still picture of the last recorded scene

gradually changes to the moving image of a new scene.

Mix Mode:

While the moving image of a new scene fades in, the still image of the last recorded scene gradually fades out.

Set [DIGITAL EFFECT] >> [EFFECT1] >> [WIPE] or [MIX] after

pressing the [MENU] Button.

≥The [WIPE] or [MIX] Indication appears.

Press the Recording Start/Stop Button to start the

Recording. Press the Recording Start/Stop Button to pause the

Recording.

≥The last scene is stored in memory. The [WIPE] or [MIX] Indication

changes to[B] or [C].

Press the Recording Start/Stop Button to restart the

Recording.

≥The last image of the previous scene gradually changes to the new

scene.

≥For other notes, see page 61.

W.B./SHUTTER/IRIS/

MF/VOL/JOG

PUSH

1, 2

PHOTO SHOT

ª Multi-Picture Mode

Strobe Multi-Picture Mode 1:

You can capture and record 9 consecutive small still pictures.

Manual Multi-Picture Mode

You can manually capture and record 9 small still pictures.

After setting [CAMERA FUNCTIONS] >> [DIGITAL EFFECT] >>

[EFFECT1] >> [MULTI].....

Set [MULTI-PICTURES] >> [SCAN MODE] >> [STROBE] or

[MANUAL].

When [STROBE] is selected:

≥Set the [SPEED] to a desired strobe speed.

[FAST]: You can capture 9 consecutive still pictures within

[NORMAL]: You can capture 9 consecutive still pictures within

[SLOW]: You can capture 9 consecutive still pictures within

≥If you set [SWING] on the [MULTI-PICTURES] Sub-Menu to [ON], the

intervals at which the 9 still pictures are taken are longer at the beginning and end than in the middle of the swing strobe period, and it is useful for analyzing swing motion, etc., in sports.

When [MANUAL] is selected:

≥You can select a desired scene one at a time up to 9 small pictures.

Exit the menu by pressing the [MENU] Button.

Press the [MULTI] Button.

≥If [MANUAL] is selected, press the [MULTI] Button at each scene you

want to capture.

Press the Recording Start/Stop Button or the [PHOTO SHOT]

approximately 1 second

approximately 1.5 seconds

approximately 2 seconds

Button to record on the Cassette.

Deleting all the captured Multi-Pictures

While 9 multi-pictures are displayed, press the [MULTI] Button. ≥If [MANUAL] has been selected, press the [MULTI] Button after 9 pictures

are displayed.

To Display the Multi-Pictures again

Press the [MULTI] Button for 1 second or longer.

To Delete Multi-Pictures one by one (When pictures were captured in [MANUAL]

When the [MULTI] Button is pressed for 1 second or longer while the still pictures are displayed, the picture captured last is deleted. If you keep pressing the [MULTI] Button, the pictures are deleted continuously. ≥After still pictures are deleted one by one, they cannot be displayed again.

））））

W.B./SHUTTER/IRIS/

MF/VOL/JOG

PUSH

1, 2

PHOTO SHOT

≥For other notes, see page 61.

~~~~~~~~~~~~~~~~~~~~~~~~~

ª Picture-in-Picture Mode

You can display a sub-screen (still picture) inside the screen.

After setting [CAMERA FUNCTIONS] >> [DIGITAL EFFECT] >>

[EFFECT1] >> [P-IN-P]......

Select [P-IN-P] on the [MULTI-PICTURES] Sub-Menu and set

the position (

1234

picture. Exit the menu by pressing the [MENU] Button.

Aim the Palmcorder at the scene you want to capture and

press the [P-IN-P] Button to insert a small still picture.

≥A small still picture is displayed in a Normal picture. ≥If the [P-IN-P] Button is pressed again, the small still picture is cleared.

Press the Recording Start/Stop Button or the [PHOTO SHOT]

Button to record on the Cassette.

≥For other notes, see page 61.

) where you want to insert a small still

VCR Mode

Playing Back

The recorded scene can be played back immediately after recording.

Slide the [OFF/ON/MODE] Switch and set the Palmcorder in

the VCR Mode.

≥The [VCR] Lamp lights up.

Press the [6] Button to rewind the tape.

≥Rewind the tape to the point where you want to start playback. ≥When the tape reaches the beginning, rewinding stops automatically.

Press the [1] Button to start playback.

To Stop Playback

Press the [∫] Button 2. ≥If a Cassette recorded with copyright protection signals is played back, the

screen becomes blue or mosaic-like noise patterns appear.

ª Adjusting the Sound Volume

Until the [VOLUME] Indication 3 appears, keep pressing the [PUSH] Dial

. Then, rotate the [PUSH] Dial to adjust the volume. After the adjustment,

press the [PUSH] Dial to make the [VOLUME] Indication disappear. To adjust the volume with the Remote Controller, press the [T] or [W] Button to display the [VOLUME] Indication. Press the [T] Button to increase the volume or press the [W] Button to decrease the volume. The [VOLUME] Indication goes off 2 or 3 seconds after the adjustment is finished. ≥When the Playback Zoom Function is in use, the sound volume cannot be

adjusted.

≥For other notes, see page 62.

CAMERA VCR

CARD P. B.

OFF ON

POWER

BACKLIGHT

CAMERA

STILL

W.B./SHUTTER/IRIS/

MF/VOL/JOG

PUSH

MODE

~~~~~~~~~~~~~~~~~~~~~~~~

Finding a Scene You Want to Play Back

ª Cue/Review Playback

Cue Playback

Press the [5] Button 1 during playback.

Review Playback

W.B./SHUTTER/IRIS/

MF/VOL/JOG

PUSH

BACKLIGHT

CAMERA

STILL

1 2

Press the [6] Button 2 during playback. ≥If the Button is held continuously, it turns to Cue Playback or Review

Playback until you release it.

≥If the Button is pressed briefly, Cue Playback or Review Playback continues

even when it is released.

ª Hyper Check Function

If you press the [5] Button during fast-forwarding of the tape or the [6] Button during rewinding of the tape, Cue Playback or Review Playback continues for as long as the Button is held down.

ª Variable Speed Search Function

The speed of Cue Playback or Review Playback can be varied.

During playback, press the [1] Button.

≥[1k!] Indication appears.

Rotate the [PUSH] Dial and select a desired search speed.

The following 6 playback speeds are available for the Variable Speed Search Function in both the fast-forwarding and rewinding directions. 1/5k (slow playback, SP mode only), 1/3k (slow playback, LP mode only),1k, 2k, 5k, 10k, and 20k. ≥The same setting can be performed using the Remote Controller’s the

[VAR.SEARCH] Button, the [π] Button and the [∫] Button.

Resuming Normal Playback

Push the [1] Button. ≥During Cue or Review Playback, fast-moving images may show mosaic-like

noise patterns. This is not a malfunction.

≥The sound is muted during search.

ª Repeat Playback

If you hold down the [1] Button for 5 seconds or longer, the Palmcorder switches to Repeat Playback Mode, and the [R !] Indication appears (To cancel Repeat Playback Mode, set the [OFF/ON/MODE] Switch to [OFF].)

1 2

COUNTER

PHOTO

DATE/

OSD

SHOT

TIME

RESET

COUNTER

STILL ADV

OFF/ON

P.B.DIGITAL

OSD

MULTI/ P-IN-P

/REW

615

STILL ADV

INDEX INDEX

SELECT

STORE

TITLE

MULTI/

¥REC

A.DUB

P-IN-P

/REW

615

INDEX INDEX

SELECT

STORE

DATE/

TIME

RESET

¥REC

PLAY

PAUSE

STOP

;

∫

VAR.

PLAY

PAUSE

;

STOP

∫

VAR.

PHOTO

SHOT

TITLE

A.DUB

FF/

STILL ADV

FF/

STILL ADV

START/ STOP

ZOOM

sVOLr

P.B.

ZOOM

ITEM

START/

STOP

ZOOM

sVOLr

ZOOM

P.B.

SET

CAMERA

STILL

W.B./SHUTTER/IRIS/

BACKLIGHT

1 2

MF/VOL/JOG

PUSH

Slow Motion Playback

This Palmcorder can play back at a slow speed.

Press the [1] Button.

Press the [E] Button or the [D] Button on the Remote

Controller.

≥When the [E] Button is pressed, Slow Motion Playback proceeds in the

reverse direction, while pressing the [

D] Button starts Slow Motion

Playback in the forward direction. Scenes recorded in the SP mode are played back at approximately 1/5th of the normal speed. Scenes recorded in the LP mode are played back at approximately 1/3rd of the normal speed.

Resuming Normal Playback

Press the [1] Button.

~~~~~~~~~~~~~~~~~~~~~~~~~

Still Playback/Still Advance Playback

This Palmcorder is capable of still picture playback and frame-advance playback.

Press the [1] Button.

Press the [;] Button.

≥The playback image stops in the Still Playback Mode.

Press the [E] Button or the [D] Button on the Remote

Controller.

≥With each pressing of the [E] Button, still pictures advance in the

reverse direction. With each pressing of the [

advance in the forward direction. If either one of the Buttons is pressed

continuously, still pictures advance continuously one frame at a time

until the Button is released.

D] Button, still pictures

Resuming Normal Playback

Press the [1] Button or [;] Button.

ª Jog Playback

By rotating the Jog Dial ([PUSH] Dial) 1 of the Palmcorder in the Still Playback Mode, still pictures can be advanced one frame at a time in the forward or reverse direction.

≥If the Palmcorder is left in the Still Playback Mode for more than 5 minutes,

the Palmcorder switches to the Stop Mode to protect the video heads from excessive wear and tear.

W.B./SHUTTER/IRIS/

MF/VOL/JOG

PUSH

BLANK

~~~~~~~~~~~~~~~~~~~~~~~~~

Finding the End of a Recording

(Blank Search Function)

The Blank Search Function helps you to locate the end of a Recording on the Cassette quickly.

Set [VCR FUNCTIONS] >> [PLAYBACK FUNCTIONS] >>

[BLANK SEARCH] >> [YES].

≥The [BLANK] Indication 1 appears. ≥Approximately 1 second before the last recorded scene, the Palmcorder

switches to the Still Playback Mode.

≥If there is no blank portion left on the Cassette, the Palmcorder stops at

the end of the tape.

Canceling Blank Search prior to completion

Press the [∫] Button.

2, 2

4 2

DATE/

OSD

TIME

COUNTER

RESET

MULTI/

¥REC

P-IN-P

/REW

PLAY

615

STILL ADV

PAUSE

;

INDEX INDEX

STOP

∫

SELECT

VAR.

STORE

OFF/ON

P.B.DIGITAL

INDEX

S 1

PHOTO

SHOT

TITLE

A.DUB

FF/

STILL ADV

ITEM

START/

STOP

ZOOM

sVOLr

P.B.

ZOOM

W.B./SHUTTER/IRIS/

MF/VOL/JOG

PUSH

SET

Index Search Functions

To facilitate searching of desired scene, this Palmcorder automatically

records index signals during recording, as explained in the following.

PhotoShot Index Signal

These signals are automatically recorded whenever still pictures are taken in

PhotoShot Mode (l 21).

When recording still pictures using the Continuous PhotoShot Mode (l 21),

the index signal is not recorded.

Scene Index Signal

Scene Index Signals are automatically recorded when you start recording

after inserting a Cassette.

However, if the Palmcorder is switched from the VCR Mode to Camera Mode,

or if the date and time is set before the start of recording, the index signal is

not recorded.

≥If [INDEX] of [RECORDING SETUP] Sub-Menu on the

[CAMERA FUNCTIONS] Main-Menu is set to [2HOUR], an index signal is recorded when Recording is restarted after a lapse of 2 hours or longer. If it is set to [DAY], an index signal is recorded when recording is restarted after the date has changed since the last recording. (While the index signal is

flashes for a few seconds.)

recorded, the [INDEX] Indication

ª PhotoShot Index Search

Set [VCR FUNCTIONS] >> [PLAYBACK FUNCTIONS] >> [INDEX] >> [PHOTO].

Press the [9] Button 1 or the [

] Button 2 on the

Remote Controller.

≥With each press of the corresponding button, still pictures recorded in

PhotoShot Mode are searched.

≥After Pictures with Sounds are played back for 4 seconds, the Palmcorder

switches to the Still Playback Mode.

ª Scene Index Search

Set [VCR FUNCTIONS] >> [PLAYBACK FUNCTIONS] >>

1111

[INDEX] >> [SCENE]. Press the [9] Button 1 or the [

2222

Remote Controller.

≥When the corresponding Button is pressed once, the [S 1] Indication 2

appears, and searching of the subsequent scene marked with an index signal starts. Each time the button is pressed after the start of Scene Index Search, the indication changes from [S 2] to [S 9], and the beginning of the scene corresponding to the selected number will be searched. After reaching the desired scene, playback starts automatically.

≥Up to 9 scene numbers can be selected.

Top Scan

If the [9] Button or the [:] Button is pressed for more than 2 seconds,

the Palmcorder will scan for scenes (or PhotoShots) and playback the first

few seconds of each. (To cancel, press the [

] Button 2 on the

1] Button

or the [∫] Button

≥For other notes, see page 62.

+ 130 hidden pages