Panasonic PVD4745 DoubleFeature OmniVision VHS, PVD4745S DoubleFeature OmniVision VHS User Manual

DVD/VCR DECK

Operating Instructions

Model No.

PV-D4745 / PV-D4745S

For Your InformationVCR Operation DVD OperationBasic OperationInitial Setup

Connections and Initial Setup Procedures are on pages 12 to 17.

MULTI FORMAT PLAYBACK

Ability to play back may depend on recording conditions.

*

As an ENERGY STAR Partner, Panasonic Corporation of North
America has determined that this product or product model meets the

E

NERGY STAR guidelines for energy efficiency.

Please read these instructions carefully before attempting to connect,
operate or adjust this product. Please save this manual.
Spanish Quick Use Guide is included.
(Guía para rápida consulta en español está incluida.)

For assistance, please call : 1-800-211-PANA(7262) or, contact us via the web at:http://www.panasonic.com/contactinfo

®

®

LSQT0908 A

Important Safeguards and Precautions

TO REDUCE THE RISK OF ELECTRIC SHOCK, FIRE, INJURY TO PERSONS OR DAMAGE TO
THIS PRODUCT, READ AND RETAIN ALL SAFETY AND OPERATING INSTRUCTIONS. HEED ALL
WARNINGS IN THE MANUAL AND ON THE PRODUCT.

INSTALLATION

1 POWER SOURCE CAUTION

Operate only from a power source indicated on the unit or in this
manual. If necessary, have your Electric Utility Service
Company or Video Products Dealer verify the power source in
your home.

2 POLARIZED OR GROUNDING PLUG

As a safety feature, this product comes with either a polarized
power cord plug (one blade is wider than the other), or a three-

wire grounding type plug.
POLARIZED PLUG CAUTION:
This plug will only fit into an outlet one way. If you cannot fully insert
the plug, try reversing it. If it still will not fit, have an electrician
install the proper wall outlet. Do not defeat the safety feature by
tampering with the plug.
GROUNDING PLUG CAUTION:
This plug will only fit into a three-hole grounding outlet. If necessary,
have an electrician install the proper outlet. Do not defeat the safety
feature by tampering with the plug.

3 POWER CORD

Make sure power cords are routed so that they are not likely to

have anything rest on them, roll over them, or be in the way of

walking traffic. If an extension cord is used, make sure it also

has either a polarized or grounded plug and that the cords can

be securely connected. Frayed cords, damaged plugs, and

damaged or cracked wire insulation are hazardous and should

be replaced by a qualified service technician.

Overloaded outlets and extension cords are fire hazards and

should be avoided.

4 DO NOT BLOCK VENTILATION HOLES

Ventilation openings in the cabinet release heat generated during

operation. If they are blocked, heat build-up inside the unit can

cause failures that may result in a fire hazard or heat damage to

cassettes or discs.

For protection, follow these rules:

a. Never cover ventilation slots or the unit while in use, or

operate the unit when placed on a bed, sofa, rug, or other
soft surface.

b. Avoid built-in installation, such as a book case or rack,

unless proper ventilation is provided.

5 PLACEMENT: AVOID EXTREMELY HOT LOCATIONS OR

SUDDEN TEMPERATURE CHANGES

Do not place the unit over or near heater or radiator, in direct

sunlight, inside closed vehicles, in high temperature [over 104°F

(40°C)], or in over 75% humidity. If the unit is suddenly moved

from a cold place to a warm one, moisture may condense in the

unit and on the tape causing damage. Never subject the unit to

vibration, impact, or place it so that the surface is tilted as

internal parts may be seriously damaged.

6 TO AVOID PERSONAL INJURY

• Do not place unsecured equipment on a
sloping surface.

• Do not place this unit on any support that
is not firm, level, and adequately strong.
The unit could fall causing serious injury
to a child or adult and damage to the unit.

• An appliance and cart combination should
be moved with care. Quick stops, excessive force, and
uneven surfaces may cause the appliance and cart
combination to overturn.

• Carefully follow all operating instructions and use the
manufacturer's recommended accessories when operating
this unit or connecting it to any other equipment.

2

OUTDOOR ANTENNA INSTALLATION

1 SAFE ANTENNA AND CABLE CONNECTION

If an outside antenna or cable system is connected to the equipment, be sure the
antenna or cable system is grounded so as to provide some protection against
built up static charges and voltage surges.
Section 810 of the National
Electrical Code, ANSI/NFPA 70
(in Canada, part 1 of the Canadian Electrical
Code) provides information with respect to
proper grounding of the mast and supporting
structure, grounding of the lead-in wire to an
antenna discharge unit, size of grounding conductors,
location of antenna discharge unit, connection to grounding

NEC - NATIONAL

ELECTRICAL CODE

ELECTRIC
SERVICE
EQUIPMENT

GROUND
CLAMP

ANTENNA
LEAD IN
WIRE

ANTENNA
DISCHARGE UNIT
(NEC SECTION 810-20)

GROUNDING CONDUCTORS
(NEC SECTION 810-21)

GROUND CLAMPS

POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250, PART H)

electrodes and requirements for the grounding electrode.

2 KEEP ANTENNA CLEAR OF HIGH VOLTAGE POWER LINES OR

CIRCUITS

An outside antenna system should be located well away from power lines,
electric light or power circuits and where it will never come into contact with
these power sources if it should happen to fall. When installing an outside
antenna, extreme care should be taken to avoid touching power lines, circuits or
other power sources as this could be fatal. Because of the hazards involved,
antenna installation should be left to a professional.

USING THE UNIT

If the unit has been in storage or moved to a new location, refer first to the
INSTALLATION section of these safeguards.

1 KEEP THE UNIT AWAY FROM WATER OR MOISTURE OF ANY KIND.
2 IF EQUIPMENT IS EXPOSED TO RAIN, MOISTURE, OR STRONG

IMPACT, unplug the unit and have it inspected by a qualified service technician

before use.

3 DURING AN ELECTRICAL STORM

During a lightning storm, whether indoors or outdoors, or before leaving the unit
unused for extended periods of time, disconnect all equipment from the power
source as well as the antenna and cable system.

4 WHEN THE UNIT IS PLUGGED IN

• Never expose the unit to rain or water. DO NOT OPERATE if liquid has been
spilled into the unit. Immediately unplug the unit, and have it inspected by a
service technician. Fire and shock hazards can result from electrical shorts
caused by liquid contact inside.

• Never drop or push any object through openings in the unit. Some internal parts
carry hazardous voltages and contact can cause electric shock or fire hazard.
Do not put any foreign object on the disc tray.

• Avoid placing the unit directly above or below your TV set as this may cause
electrical interference. Keep all magnets away from electronic equipment.

5 USING ACCESSORIES

Use only accessories recommended by the manufacturer to avoid risk of fire,
shock, or other hazards.

6 CLEANING THE UNIT

Unplug the unit. Then, use a clean, dry, chemically untreated cloth to gently
remove dust or debris. DO NOT USE cleaning fluids, aerosols, or forced air that
could over-spray, or seep into the unit and cause electrical shock. Any substance
such as wax, adhesive tape, etc. may mar the cabinet surface. Exposure to
greasy, humid, or dusty areas may adversely affect internal parts.

SERVICE

1 DO NOT SERVICE THIS PRODUCT YOURSELF

If, after carefully following the detailed operating instructions, this product
does not operate properly, do not attempt to open or remove covers, or make
any adjustments not described in the manual. Unplug the unit and contact a
qualified service technician.

2 IF REPLACEMENT PARTS ARE REQUIRED

Make sure the service technician uses only parts specified by the
manufacturer, or those having the same safety characteristics as the original
parts. The use of unauthorized substitutes may result in fire, electric shock,
or other hazards.

3 HAVE THE SERVICE TECHNICIAN PERFORM A SAFETY CHECK

After any service or repairs to the unit, request the service technician to
conduct a thorough safety check as described in the manufacturer’s service
literature to ensure that the unit is in safe operating condition.

Safety Precautions/Mesures de sécurité

1

To prevent fire or shock hazard, do not expose this equipment to rain
or moisture.

To prevent electric shock, match wide blade of plug to wide slot, fully insert.

AVERTISSEMENT:

Afin de prévenir tout risque d’incendie ou de chocs électriques, ne pas
exposer cet appareil à la pluie ou à une humidité excessive.

ATTENTION:

Pour éviter les chocs électriques, introduire la lame la plus large de la
fiche dans la borne correspondante de la prise et pousser jusqu’au fond.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK)

NO USER-SERVICEABLE PARTS INSIDE

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL

CAUTION:

UNIT IS A CLASS I LASER PRODUCT.
THIS UNIT USES A VISIBLE LASER BEAM WHICH COULD CAUSE
HAZARDOUS RADIATION EXPOSURE IF DIRECTED.
BE SURE TO OPERATE THE UNIT CORRECTLY AS INSTRUCTED.

WHEN THIS UNIT IS PLUGGED TO THE WALL OUTLET, DO NOT PLACE
YOUR EYES CLOSE TO THE OPENING OF THE DISC TRAY AND OTHER
OPENINGS TO LOOK INTO THE INSIDE OF THIS UNIT.

USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF
PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN
HAZARDOUS RADIATION EXPOSURE.

DO NOT OPEN COVERS AND DO NOT ATTEMPT TO REPAIR YOURSELF.
REFER SERVICING TO QUALIFIED PERSONNEL.

This symbol warns the user that uninsulated voltage within the unit may
have sufficient magnitude to cause electric shock. Therefore, it is
dangerous to make any kind of contact with any inside part of this unit.

This symbol alerts the user that important literature concerning the
operation and maintenance of this unit has been included.
Therefore, it should be read carefully in order to avoid any problems.

CAUTION:

LASER RADIATION
WHEN OPEN. DO NOT
STARE INTO BEAM.

ATTENTION:

RAYONNEMENT
LASER EN CAS
D’OUVERTURE.
NE PAS REGARDER
DANS LE FAISCEAU.

(Inside of product)

FCC NOTE:

This equipment has been tested and found to comply with part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference when operated in a
residential environment. If this equipment does cause interference to radio or television reception,
which can be determined by turning the equipment off and on, use the equipment in another
location and/or utilize an electrical outlet different from that used by the receiver.
If necessary, consult the dealer or an experienced radio/TV technician for help. The user may find
the booklet, “Something About Interference” available from FCC local regional offices helpful.

FCC Caution:

To assure continued compliance, (example- use only shielded interface cables when connecting
to other devices.) Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate this equipment.

Region Management Information:

This DECK is designed and manufactured to respond to the
Region Management Information that is recorded on a DVD
disc. If the Region number described on the DVD disc does
not correspond to the Region number of this DECK, this
DECK cannot play this disc.

● The Region number for this DECK is “1”.

● The Player will play DVD-Video marked with labels

containing “1” or “ALL”.

Example:

ALL

1

2

4

3

Before Using

Congratulations

on your purchase of one of the most
sophisticated and reliable products on the
market today. Used properly, it will bring you
years of enjoyment. Please fill in the information
below. The serial number is on the tag located
on the back of your DECK.

• Date of Purchase

• Dealer Purchased From

• Dealer Address

• Dealer Phone No.

• Model No.

• Serial No.

Accessories

Remote Control

EUR7724KF0

Batteries 2 “AA”

RF Coaxial Cable
LSJA0418

To order accessories,
call toll free
1-800-332-5368.

Head Cleaning

Playing older or damaged tapes may eventually
cause video heads to become clogged.

Video Head Clog Sensor

During playback, this screen
appears if clogging is detected.
To remove screen, press PLAY
on the remote or DECK.

• Use “dry” type head cleaning cassette only.

(Part No. NV-TCL30PT is recommended.)

• Follow cleaning tape instructions carefully.
Excessive use of tape can shorten head life.

• If head clog symptoms persist, contact your
nearest servicenter by visiting our Web Site
(see p. 61).

Cleaning DECK

Use a soft cloth or dusting attachment of a vacuum
cleaner to remove dust from the ventilation holes on
the back sides and bottom of the cabinet.
Plastic surfaces are easily scratched and can be
marred by alcohol and various solvents.
Avoid excessive use of oil-based furniture polishes
since the materials used in the cabinet will
accumulate more dust. We recommend using a
non-abrasive, antistatic cleaner and polisher.

Loading the Batteries

1) Open cover.

2) Insert batteries as
marked.

3) Close cover.

Battery replacement caution

• Do not mix old and new batteries.

• Do not mix alkaline with manganese batteries.

Record/ Playback Time

Only use tapes with the mark in this DECK.

Tape Speed

Setting

SP

(Standard Play)

SLP

(Super Long Play)

Type of Video Cassette

2 Hours

6 Hours 8 Hours

2 Hours

40 Minutes

3 Hours

9 Hours

T180T160T120

Features for a Quality Picture (VCR)

Digital Auto Picture

Automatically controls the video output signal for
less noise depending on the tape condition.

Digital Auto Tracking

Continuously analyzes the signal and adjusts for
optimum picture quality.

Manual Tracking Control
(to reduce picture noise)

Use during Playback and Slow Motion mode to
reduce picture noise.
Press CH (TRACKING) / on the remote control
or on DECK until the picture clears up.
To return to Auto Tracking, press POWER off, then
on again a few seconds later.

R

R

R

R

V-Lock Control (to reduce picture jitter)

In Still mode, CH (TRACKING) / operate as a
V-Lock control.

R

R

R

R

4

For assistance, please call : 1-800-211-PANA(7262) or, contact us via the web at:http://www.panasonic.com/contactinfo

Table of Contents

Initial Setup (Connection)

DVD / VCR

Important Safeguards and Precautions ............................... 2, 3

Before Using ...............................................................................4

DECK & Cassette Information .............................................. 6 , 7

Location of Controls .......................................................... 8 ~ 10

On Screen Displays / Light-up Indicators............................... 11

Connections ..................................................................... 12 ~ 15

Initial Setup for Basic Connections (Ready to Play) ............. 16, 17

Basic Operation

VCR

Reset Language, Channels, Clock, VCR’s Output Channel ........ 18, 19

Playback/ Record on a Tape.............................................. 20, 21

DVD

Basic DVD Operation ......................................................... 22, 23

Initial Setup Basic Operation VCR Operation DVD Operation For Your Information

VCR Operation

Timer Recording ................................................................. 24, 25

MTS Broadcast/ VHS Hi-Fi Stereo System ....................... 26, 27

Multi-Brand Control Feature .............................................. 28, 29

Tape Operation (Search System) .......................................... 30 ~ 32

Special VCR Features ........................................................ 33, 34

Copying Your Tapes (Dubbing) ............................................................ 35

DVD Operation

Disc Operation .................................................................. 36 ~ 41

DVD-RAM Operation (DVD-RAM only) ....................................42, 43

DVD Operation using On-Screen Displays .................... 44 ~ 48

MP3/JPEG Playback Operation ....................................... 49 ~ 51

Settings for DVD Operation ............................................. 52 ~ 55

A/V OPTIMIZER ......................................................................... 55

Language Code List .................................................................56

For Your Information

Warning and Instruction Displays........................................... 57

Before Requesting Service................................................ 58, 59

Limited Warranty ................................................................ 60, 61

Customer Services Directory .................................................. 61

Spanish (Español) Quick Use Guide............................... 62 ~ 69

Index .................................................................................... 70, 71

5

DECK & Cassette Information

Prevent Accidental Tape Erasure

Break off the tab to
prevent recording.

Record Tab

Screw driver

To record again

Cover the hole
with cellophane tape.

Disc formats supported by this DECK

DECK can play back discs bearing any of the
following marks:

Logo Disc type

DVD-RAM (Version 1.1 of the
Video Recording Format a
unified video recording
standard)

DVD (DVD-Video)

DVD-R (DVD-Video formatted
discs [finalized])

Video CD

CD (CD-DA)
CD-R/CD-RW

• CD-DA format

• MP3/JPEG file

and finalized.*

DVD-RAM discs

DVD-RAM discs must meet the following conditions
for this unit to be able to play them.

• Non-cartridge discs

Type

Capacity

• Remove TYPE 2 and 4 discs from their cartridges

before use, then return them when you are finished.
Read the instructions for the disc carefully.

• Some parts of the disc, for example where one program

ends and another begins, may not play smoothly.

• Discs that can be removed from
their cartridges (TYPE 2 and 4)

• 12 cm (5”) 9.4 GB (double-sided)
and 4.7 GB (single-sided)

• 8 cm (3”) 2.8 GB (double-sided)

Disc Handling

Handling precautions

• Sticking a label on the disc may impair DVD-R playback.

• Do not attach sticker to discs. (Do not use discs with

exposed adhesive from tape or left over peeled-off
stickers.)

• Only hold disc by edges as shown below. Fingerprints,
dirt and scratches can cause skipping and distortion.

• Do not write on label side of disc.

• Never use record cleaning

sprays, benzine, thinner,
static electricity prevention
liquids, or any other solvent.

Disc tray

Disc

[Discs Played 8cm (3") or 12cm (5")]
*A process that allows play on compatible equipment.

Discs which cannot be played

• DVD with Region No. other than “1” or “ALL”

• PAL discs, DVD-ROM, DVD-Audio, DVD-RW,

DVD+R, DVD+RW, CD-ROM, CDV, CD-G, CVD,
SVCD, SACD, CD-TEXT, Divx Video Disc,
Photo-CD and MPEG4 Video Disc

Notes

• Do not use irregularly shaped discs (e.g. heart­shaped), as these can damage the unit.

• It may not be possible to play CD-R, CD-RW,
DVD-R and DVD-RAM in all cases due to the
type of disc or condition of the recording.

6

For assistance, please call : 1-800-211-PANA(7262) or, contact us via the web at:http://www.panasonic.com/contactinfo

• Do not try to close disc tray when disc is not
properly placed.

To clean disc surface

With a soft, damp (water only) cloth,
gently wipe from the center hole to the
outer edge as shown below. (Wiping in a
circular pattern will scratch the surface.)

• DVD-RAM, DVD-R :
Clean only with the DVD-RAM disc
cleaner available. Never use cloths or
cleaners for CDs etc.

If disc is brought from a cold to a warm
environment, moisture may form on the disc

Wipe away moisture with a soft, dry, lint-free cloth
before using disc. (See above.)

Improper disc storage

Discs could be damaged if stored or left in areas:

• exposed to direct sunlight.

• that are humid or dusty.

• near heat (i.e. heater, radiator, etc.).

Specifications

Power Source: 120 V AC, 60 Hz
Power Consumption: Power On: Approx. 22 watts, Power Off: Approx. 0.9 watts
Video Signal: EIA Standard NTSC color
Video Recording System: 4 rotary heads helical scanning system
Audio Track: 1 track (Normal), 2 channel (Hi-Fi Audio Sound)
Tuner
Broadcast Channels: VHF 2 ~ 13, UHF 14 ~ 69
CABLE Channels: Midband A through I (14 ~ 22), Superband J through W (23 ~ 36)

Hyperband AA ~ EEE (37 ~ 64), Lowband A-5 ~ A-1 (95 ~ 99)
Special CABLE channel 5A (01), Ultraband 65 ~ 94, 100 ~ 125

Input/Output Terminal: Audio/Video Line Input/Output, RF Input/Output
Input Terminal: Audio/Video Line Input (Front)
Output Terminal: S-Video Output (DVD only), Component Video Output (DVD only)

Audio Output 2 (L), (R)

Operating Temperature: 5 °C ~ 40 °C (41 °F ~ 104 °F)
Operating Humidity: 10 % ~ 75 %
Weight: 3.7 kg (8.2 lbs.)
Dimensions: 430 (W) x 93 (H) x 255 (D) mm

16-15/16” (W) x 3-11/16” (H) x 10-1/16” (D) inch

Discs Played
(1) DVD-Video Disc 5” (12 cm) single-sided single-layer

5” (12 cm) single-sided double-layer
5” (12 cm) double-sided double-layer (one layer per side)
3” (8 cm) single-sided single-layer
3” (8 cm) single-sided double-layer
3” (8 cm) double-sided double-layer (one layer per side)

DVD-RAM Disc 5” (12 cm) 9.4 GB (double-sided) and 4.7 GB (single-sided)

3” (8 cm) 2.8 GB (double-sided)

(2) Compact Disc 5” (12 cm) disc
(CD-DA, Video CD) 3” (8 cm) disc
(CD-R/CD-RW, MP3, JPEG)

Digital Audio Output: Digital Optical Connector
Pickup: Wavelength : 655 nm (DVD), 790 nm (Video CD/CD)

Laser power: CLASS II

Note: Designs and specifications are subject to change without notice.

Initial Setup

Definition of Terms (DVD)

Angle: Some DVD discs feature scenes simultaneously shot from different angles.

The ANGLE button can be used to view the scene from different angles.

Chapter Number:Titles are subdivided into numbered sections. You can quickly search for

a favorite scene using these numbers.

DVD: A high-density optical disc on which high-quality pictures and sound have been

digitally recorded. DVD incorporates video compression technology (MPEG II)
and high-density recording technology which allow entire movies to be recorded
with incredible playback quality.

Playback Control:With Video CD (version 2.0), scenes or information may be selected for viewing or

listening from an interactive menu that appears on the TV screen.

Subtitles: Written dialogue which appears at the bottom of the screen.
Time Number: The elapsed play time from the start of a disc or title. Use to quickly find scenes.

(May not work with some discs.)

Title Number: For DVD discs with two or more titles, the title is numbered as title 1, title 2, etc.
Track Number: Numbers assigned to tracks on Video CDs and CDs to allow specific tracks to be

quickly located.

Video CD: CD containing picture and sound with same quality level as video tape.

This DECK also supports Video CDs with playback control (version 2.0).

U.S. Patent Nos. 4,631,603; 4,577,216; 4,819,098; 4,907,093; 5,315,448; and 6,516,132.

This product incorporates copyright protection technology that is protected by U.S. Patents and other
intellectual property rights. Use of this copyright protection technology must be authorized by
Macrovision, and is intended for home and other limited viewing uses only unless otherwise authorized
by Macrovision. Reverse engineering or disassembly is prohibited.

7

Location of Controls

Remote Control

EJECT /

OPEN / CLOSE

pp. 20,

POWER

NUMBER keys

ADD/DELETE /

pp. 19,

ACTION

pp. 18

SET

VCR mode

p. 28

STOP

pp. 20,

REWIND /

SLOW-

pp. 20,

FAST FORWARD /

SEARCH / SLOW+

pp. 20,

PAUSE /

pp. 20,

22

CLEAR

38, 40

, 52

22

SEARCH

23

23

STILL

23

Bold: VCR Function /

Italic

:

DVD Function

/

Bold Italic:VCR and DVD Functions

/ Normal: Others

CHANNEL

TRACKING

/

V-LOCK

VOLUME

MENU / PLAY LIST

Virtual Surround Sound (V.S.S.)

VCR/TV

p. 21

TV mode

p. 28

/ /

/

pp. 4, 21,

SELECT

DVD mode

pp. 20,

SKIP+

SKIP-

pp.

10

22

+

/

-

p. 28

p

. 41, 43

p.

28

PLAY

22

p

. 23

ENTER

23,

28

ZOOM

p

. 37

/

ANGLE

p

. 37

TAPE POSITION

SUB TITLE

p

. 36

TITLE

/

DIRECT NAVIGATOR

p

. 41, 42

RETURN /

INPUT

p. 35

COMMERCIAL SKIP

DISPLAY

p. 11,

44

RECORD

p. 21

SPEED

p. 21

EJECT button: When this button is pressed in VCR mode, the tape is ejected.

This button is inoperative if pressed during recording.
If pressed in DVD mode, the disc tray opens or closes.

/

STATUS

p. 32

AUDIO

(SAP / Hi-Fi)

pp. 27,

SEARCH

pp

. 22,

ZERO SEARCH

A/V OPTIMIZER

pp. 30,

COUNTER RESET

p. 30

PROGRAM

p. 24

36

30

55

/

8

For assistance, please call : 1-800-211-PANA(7262) or, contact us via the web at:http://www.panasonic.com/contactinfo

Front View of DECK

Bold: VCR Function

Italic

:

Bold Italic

Normal: Others

PLAY

p. 20

DVD Function

:

VCR and DVD Functions

If the disc cannot be removed...

Initial Setup

First, unplug DECK. Then, prepare a rigid
wire (e.g. an extended paper clip) and,
applying moderate force, insert it straight
into the hole at the base of the tray.
The tray will eject a little. Now, pull the tray
all the way out and remove the disc.

STOP/EJECT

p. 20

POWER

Audio/Video
Input Connector 2
(LINE 2)

REC

p. 21

CHANNEL /
TRACKING/V-LOCK

pp. 4, 21

p. 35

Cassette
Compartment

Light-up

Indicators

Remote
Sensor

p. 11

Over 2 inches

Disc Tray

OPEN/CLOSE

p.

22

PLAY

p.

22

STOP

p.

22

FAST FORWARD

/

SEARCH

SKIP

p. 20,

23

/

REWIND /

Reset All Memory Functions

Returns to factory setting. Use if relocating DECK, or if Initial Setup needs to be redone.

• Make sure a tape is not inserted in the DECK.

Turn DECK Power on.

1

Press and hold both VCR PLAY

2

and CHANNEL on the DECK for
more than 5 seconds.

• The power shuts off.
Perform “Initial Setup (Ready to Play)”

3

21

on page 16.

SEARCH

SKIP

p. 20,

/

23

9

Location of Controls (continued)

Rear View of DECK

AC Power Plug

• While plugged into an AC outlet,
this DECK consumes 0.9 W of
electrical power in off mode.

Component Video Output
Connector (Y, P
(DVD Only)

p.

13

Optical Digital Audio
Output Connector
(DVD Only)

p.

15

Bold: VCR Function

:

Bold Italic

VCR and DVD Functions

VHF/UHF Antenna Output Terminal
p.12

VHF/UHF Antenna Input Terminal
p. 12

Video Output

B

, PR)

Connector

p.

12

•

Video Input
Connector
p. 35

•

•

Audio Input
Connector (L/R)
p. 35

Italic:DVD Function

S-Video Out Connector
(DVD Only)

pp.

10, 13

Audio Output 2
Connector (L/R)

p.

13

Audio Output 1
Connector (L/R)

p.

12

The following table shows the status of the output jacks when in VCR or DVD mode.

Note

Video Output
Audio Out 1
Audio Out 2

VCR

DVD

• PROG functions on the remote are not available when using Component Video Output and
S-VIDEO OUT. Please set TV to either RF INPUT or VIDEO INPUT, and then press PROG.

YES
YES

Component
Video Output

N/A

S-VIDEO OUT

N/A

YES

To enjoy PROGRESSIVE SCAN video

(1). Connect

(See p. 13.)

(2). When PROGRESSIVE OUT is set to “ON” in the DVD Main Menu (p. 55), a Progressive Scan

signal is output from the

Notes

• The screen may shift off-center when using progressive output. Please adjust the screen
position if this occurs. (Refer to your TV manual.)

• If the television is not progressive compatible, a progressive scan picture is not available.
Connect the Video Output or S-Video Output connector (see p. 12, 13) and
set PROGRESSIVE OUT to “OFF” in the DVD Main Menu. (See p. 55.)

Component Video Output

Component Video Output Connector

to the component video input terminals of a television.

.

10

For assistance, please call : 1-800-211-PANA(7262) or, contact us via the web at:http://www.panasonic.com/contactinfo

On Screen Displays / Light-up Indicators

On Screen Displays (VCR)

Function & Channel Displays

When a function button
is pressed, e.g. PLAY,
or you change channels,
and also if a cassette is
inserted, a 5-second
display appears.

VCR Status & Clock Displays
To display or remove
screen shown at right,

➛➛

➛ press DISPLAY.

➛➛

Note

• For on Screen Displays in
DVD mode, see p. 44.

Cassette inserted
(Rec Time Remaining

is displayed in OTR
mode, e.g.“0:25”.
See p.21.)

Broadcast Audio
Being Received
(See pp. 26, 27.)

Light-up Indicators

Light-up indicators allow easy confirmation
of current DECK function status.

Blank Tape/ No Signal Indications

Whenever a blank section of a tape comes
up in Play mode, or when the selected
channel has no broadcast signal with Weak
Signal Display Feature (p. 33) set to OFF,
the TV screen will turn solid blue.

Function Status

Current Time Channel

Counter

Tape Speed

(See p. 4.)
Date
(When clock is set, a 5-second

display appears.)

Timer Indicator

Lights up when DECK is set for Timer Recording, or
when One Touch Recording (OTR) is used. Flashes
when Timer Recording is set, but a tape has not been
inserted into DECK and when a power interruption
occurs during Timer Programming.

Initial Setup

VCR mode Indicator

Lights when output
selection is VCR mode.
Flashes in Auto Clock
Set or Channel Auto Set.

VCR REC Indicator

Lights up during
recording. Flashes in
Rec. Pause mode.

<Light-up combination example>

Light-up Indicator Function Status

VCR +

VCR

VCR

VCR

DVD

VCR

PLAY

+

+

+

+

➛➛

➛

➛➛

➛➛

➛

➛➛

PLAY

REC

TIMER

TIMER

PLAY

REC

TIMER

+

REC

➛➛

➛

➛➛

TIMER PLAY

➛➛

➛

➛➛

REC VCR

➛➛

➛

➛➛

➛➛

➛

➛➛

PLAY Indicator

Lights during playback in
either VCR mode or
DVD mode. Flashes in
Still, Frame by Frame, or
Slow mode.

VCR playback in progress [See p. 20]

VCR recording in progress [See p. 21]

VCR timer setting in progress [See pp. 24, 25]

VCR Timer Recording in progress [See pp. 24, 25]

DVD playback in progress [See pp. 22, 23]

VCR fast forward in progress [See p. 20]

VCR rewind in progress [See p. 20]

DVD mode Indicator

Lights when output
selection is DVD mode.

11

Connections

Basic Connections

• If your TV has AUDIO and VIDEO IN terminals, connect them to DECK for higher

quality picture and sound.

• You can enjoy stereo sound even if your TV is not stereo by connecting a stereo

amplifier to DECK.

• Connect DECK and TV with an RF Coaxial Cable a (supplied) or an AV Cable
(not supplied) as shown in the figure below.

■ ■

■ DSS Receiver DECK TV

■ ■

DSS
Receiver

IN

IN

OUT

■ ■

■ DECK TV

■ ■

Antenna or Cable

or

■ ■

■ Cable Box DECK TV

■ ■

IN

OUT

Cable Box

1 Disconnect antenna or cable from TV

and connect to DECK.

2 Connect DECK to TV with RF Coaxial Cable.

DVD/VCR DECK

OUT

VIDEO

L

AUDIO

R

IN 1

IN FROM ANT.

VHF/UHF

OUT TO TV

TV

AUDIO IN

RL

RF COAXIAL CABLE

a

(supplied)

VHF/
UHF

VIDEO

IN

b

12

b

AV CABLE

When using “Nut type” RF coaxial cables, tighten with
fingers only. Overtightening may damage terminals.

Note to CABLE system installer

This reminder is provided to call the CABLE system installer’s attention to Article 820-40 of the
NEC in USA (and to the Canadian Electrical Code in Canada) that provides guidelines for proper
grounding and, in particular, specifies that the cable ground shall be connected to the grounding
system of the building, as close to the point of cable entry as practical.

For assistance, please call : 1-800-211-PANA(7262) or, contact us via the web at:http://www.panasonic.com/contactinfo

(not supplied)

Other Connections

You CannotYou Can

Initial Setup

■ ■

■ With a Cable Box (DECK

■ ■

DVD/VCR DECK

IN FROM ANT.

IN 1

OUT

VHF/UHF

OUT TO TV

■■

■

Connect With Two Cable Boxes

■■

ANT or CATV

Cable Box

Cable Box TV)

OUTIN

DVD/VCR DECK

ANT

or

CATV

Cable Box

OUT

IN

2-Way Splitter

OUT 1

OUT 2

OUT

Cable Box

IN 1

OUTIN

IN FROM ANT.

VHF/
UHF

VHF/UHF
OUT TO TV

A/B Switch

IN 2IN 1

IN

R

L

TV

OUT

IN

AUDIO

VIDEO

OUT

R
L

VHF/
UHF

TV

AUDIO

VIDEO

• view any
(including
scrambled)
channel.

• use Remote
Control to select
channels without
using Multi-brand
control feature.

• record and view
both scrambled
and unscrambled
channels if
additional
equipment is
added.
This connection
requires: two
converter boxes,
an A/B switch,
and a 2-way
splitter.

• record
scrambled
channels.

You CannotYou Can

• view a channel
other than the
one selected
for any type of
recording.

• set a Timer
recording of a
channel unless
you select it on
the Cable Box.

Connections For DVD Only (enjoying higher picture quality)

Connect AUDIO OUT2 (L, R) to the AUDIO IN (L, R) of the TV. (audio input for COMPONENT or

1

S-VIDEO mode).
If your TV has COMPONENT VIDEO INPUT, connect to COMPONENT VIDEO OUT.

2

If your TV does not have COMPONENT VIDEO INPUT but has S-VIDEO INPUT, connect to
S-VIDEO OUT.

When in DVD mode, set your TV to either COMPONENT VIDEO IN or S-VIDEO IN.

3

Notes

DVD OUTPUT

S-VIDEO OUT

• You can watch DVDs through the S-VIDEO or COMPONENT VIDEO, VHF/UHF OUT TO TV,
and VIDEO OUT connections to your TV. The VCR and TUNER pictures are available only
from the VIDEO OUT and VHF/UHF OUT TO TV connections to your TV.

• PROG functions on the remote are not available when using S-VIDEO OUT and COMPONENT
Video Output. Please set TV to either RF INPUT or VIDEO INPUT, and then press PROG.

• TV must have capability to accept and display a progressive scan signal to use
PROGRESSIVE mode. Consult your TV operating instructions.

DVD/VCR DECK

COMPONENT

VIDEO OUT

Y

P

B

P R

AUDIO OUT2

L

R

Y

PB

PR

IN

IN

L

L

AUDIO

R

R

VIDEO

S-VIDEO
IN

From DECK’s

TV

A/V OUTPUT

IN

or

13

Connections (continued)

Audio Connections

Ready Checklist

Turn down the volume, then turn DECK, as well as other equipment to be connected, off before
proceeding with connection.
Do not block ventilation holes of any of the equipment and arrange them so that air can circulate freely.
Read through the instructions before connecting other equipment.
Ensure that you observe the color coding when connecting audio and video cables.

■ Connecting Amplifier (2ch stereo system) [Analog connection]

DVD/VCR DECK

AUDIO OUT2

L

Speaker

Amplifier

AUDIO IN

R L

R

Enjoying digital audio output from the digital audio output connector

Notes on audio output from the optical digital audio output connector

Speaker

Disc

DVD-Video

DVD-RAM

Sound recording format

Dolby Digital

Linear PCM
(48/96 kHz 16/20/24 bit)

DTS
Dolby Digital

Optical digital audio output from connector

Dolby Digital bitstream (1 - 5.1 ch)
or PCM (48 kHz sampling/16 bit only)*

1

Linear PCM (2 ch)
(48 kHz sampling/16 bit only)*

2

Bitstream or PCM (48 kHz sampling/16 bit only)*
Dolby Digital bitstream (1 - 5.1 ch)

or PCM (48 kHz sampling/16 bit only)

Linear PCM(48 kHz/16 bit)

Video CD
CD
MP3

*1 The type of audio output from the connector can be selected by the Settings for DVD Operation.

(See p. 53.)

*2 When “LPCM(DVD)” is set to OFF in the DVD Main Menu, only 48 kHz sampling/16 bit is ouput.

When set to ON, sampling of sound quality greater than 48 kHz/16 bit is reduced to 48 kHz/16
bit. (See page 53.)

MPEG1
Linear PCM
MP3

Linear PCM (2 ch)
PCM (44.1 kHz sampling)
Linear PCM (44.1 kHz sampling)

PCM (It depends on the MP3 file)

For your reference:

• Dolby Digital is a digital sound compression technique developed by the Dolby Laboratories
Licensing Corporation. Supporting 5.1-channel surround sound, as well as stereo (2-channel)
sound, this technique enables a large quantity of sound data to be efficiently recorded on a disc.

• Linear PCM is a signal recording format used in CDs. While CDs are recorded in 44.1 kHz/16 bit,
DVDs are recorded in 48 kHz/16 bit up to 96 kHz/24 bit.

• If you have a Dolby Pro Logic Surround decoder, you will obtain the full benefit of Pro Logic from
the same DVD movies that provide full 5.1 channel Dolby Digital soundtracks, as well as from titles
with the Dolby Surround mark. For information on Panasonic or Technics Dolby Pro Logic Surround
Sound Decoders please contact your local dealer.

Manufactured under license from Digital Theater Systems, Inc. US Pat. No’s. 5,451,942, 5,956,674,
5,974,380, 5,978,762, 6,487,535 and other US. and world-wide patents issued and pending. “DTS”
and “DTS 2.0 + Digital Out” are trademarks of Digital Theater Systems, Inc.
Copyright 1996, 2003 Digital Theater Systems, Inc. All Rights Reserved.

1

14

Manufactured under license from Dolby Laboratories.
Dolby and the double-D symbol are trademarks of Dolby Laboratories.

For assistance, please call : 1-800-211-PANA(7262) or, contact us via the web at:http://www.panasonic.com/contactinfo

■ Connecting Amplifier (5.1 ch Surround system) [Digital connection]
DECK Dolby Digital Decoder Amplifier Speaker

or

DECK DTS (Digital Theater Systems) Decoder Amplifier Speaker

When DVDs recorded in Dolby Digital or DTS are played, Dolby Digital bitstream or DTS
bitstream is output from the DECK OPTICAL digital audio output connector. When DECK
is connected to a Dolby Digital decoder or DTS decoder, you can enjoy theater-quality
audio in your home. [An optical digital audio cable (optional) is required when an optional
Dolby Digital decoder or DTS decoder is used.]

Notes on connecting an optical
digital audio cable (optional)

• Remove the attached cap, and
firmly connect the cable to the
connector.

Initial Setup

Surround
Speaker

[5.1ch Surround system]

Surround
Speaker

Center
Speaker

DVD/VCR DECK
(Rear)

Optical Digital
Audio Cable
(optional)

Caution for optical digital audio output connector:

• When connecting an amplifier (with an Optical Digital Input Connector) which does not
contain the Dolby Digital or DTS decoder, be sure to select “PCM” at “Dolby Digital” and
“PCM” at “dts” of the Settings for DVD Operation “Audio Output” (see p. 53).
Otherwise, any attempt to play DVDs may cause such a high level of noise that it may be
harmful to your ears and damage your speakers.

• When a Dolby Digital/DTS decoder is connected, please select “Bitstream” at “dts” or
“Dolby Digital” of the Settings for DVD Operation “Audio Output”.
If “PCM” is selected, there will be stereo sound. (See p. 53.)

• Video CDs and CDs can be played as usual.

Decoder with
Dolby Digital /DTS
processing (optional)

To Optical
Digital Audio
Input Connector

Front
Speaker

Front
Speaker

Amplifier

Subwoofer

Note

• Some DTS decoders which do not support DVD-DTS interface may not work properly with DECK.

15

Initial Setup for Basic Connections (Ready to Play)

Before doing Initial Setup

Turn TV on.

1

See connections RF Coaxial Cable Connection and AV Cable Connection on page 12.

2

<RF Coaxial Cable Connection>

ÖSet TV to channel 3.

<AV Cable Connection>

ÖSet TV to VIDEO.

[DECK

3

• Go to “Initial Setup (Ready to Play).” (See below.)

[Cable Box

• Turn on Cable Box and set it to your Public Broadcasting Station (PBS) channel
in your time zone.

• If you use a DSS Receiver, it must be turned off.

➛➛

➛ TV]

➛➛

➛➛

➛ DECK

➛➛

➛➛

➛ TV], [DSS

➛➛

➛➛

➛ DECK

➛➛

➛➛

➛ TV]

➛➛

Initial Setup (Ready to Play)

Press VCR on remote for VCR mode.

1

Plug DECK Power Cord into AC wall outlet. DECK comes on and auto channel
and clock set starts.

2

• If screen below does not appear, check DECK - TV connection and, if TV is tuned to
channel 3, try switching it to channel 4.

• To change VCR’s output channel, please see “VCR’s Output Channel” on page 19.

Plug VCR Power plug into an AC wall outlet.

16

Notes

• Function buttons are void during Initial Setup.

• To eject a tape during Auto Set, press EJECT on remote

or STOP/EJECT twice on DECK.
Then make settings manually. (See p. 18.)

• If Auto Clock Set takes more than 30 minutes,
press STOP and perform settings manually. (See p. 18.)

Continued on next page...

For assistance, please call : 1-800-211-PANA(7262) or, contact us via the web at:http://www.panasonic.com/contactinfo

*Important: If a remote control button does not work when pressed,

press the VCR button on the remote and try the button again.

EJECT

ACTION

SELECT

SET

VCR

Settings are made automatically.
When complete, this screen appears.

3

If “AUTO CLOCK SET IS INCOMPLETE” appears,
manually set clock (below).

Initial Setup

STOP/EJECT

Manual Clock Set

If Auto Clock Set was incomplete.

Press ACTION* on remote to display
CLOCK screen.

1

Press
In the same manner, select and set the date,

2

year, time, and DST (Daylight Saving Time).

to select the month and SET to set.

Press ACTION to start clock and exit.

3

17

Reset Language, Channels, Clock, VCR’s O

1

2

Press ACTION*

to display MENU.

Language

1) Press to select

language item.

2) Press SET repeatedly to

change language item as
shown below.

• PROGRAM functions are not available

Channels

1) Press to select

“SET UP CHANNEL,”
and press SET.

2) Press to select

“ANTENNA,” then
press SET to set your
antenna system
(“TV” or “CABLE.”)

when using COMPONENT Video Output
and S-VIDEO OUT. Please set TV to
either RF INPUT or VIDEO INPUT, and
then press PROGRAM.

Clock

1) Press to select

“SET CLOCK,” and

press SET.

2) Press to select
“MANUAL,” and press SET.
(For Auto Clock Set, select
“AUTO CLOCK SET.”)

For Spanish

➡

➡

For French

For English

3) Press ACTION to exit.

3) Press to select

“AUTO SET,” then
press SET.

• If you use a Cable Box,
set it to the PBS channel
in your time zone.

• After Channel Auto Set
is finished, Auto Clock
Set will be performed.

(“TIME ZONE ADJUST”

appears only when auto
clock is set.)

3) Press and to

select, then set the date,
time, and DST (Daylight
Saving Time).

4) Press ACTION to start

Clock and exit this
mode.

18

For assistance, please call : 1-800-211-PANA(7262) or, contact us via the web at:http://www.panasonic.com/contactinfo

*Important: If a remote control button does not work

when pressed, press the VCR button
on the remote and try the button again.

Time Zone Adjust

(Only when Auto Clock is set.)

1) Press to select

“SET CLOCK,” and

press SET.

VCR’s Output
Channel

1) Press to select

“VCR’S OUTPUT CH.,”
and press SET.

POWER
NUMBER

keys
CH /

ADD/DLT
ACTION
SELECT

SET
VCR

Basic Operation

2) Press to select

“TIME ZONE ADJUST,”

and press SET to
subtract or add hour(s)
as necessary.

3) Press ACTION.

•“TIME ZONE ADJUST”
returns to “0” if clock is
set manually.

2) Press SET.

3) Press ACTION.

➡

After 3 seconds

Add or Delete a Channel

To add channel:
Select channel with NUMBER keys

and press ADD/DLT.

To delete channel:
Select channel with CH / or

NUMBER keys and press ADD/DLT.

DST (Daylight Saving Time)

DECK auto adjusts clock for DST.
(p. 17.)

Spring (First Sunday in April)

DST:ON

➛➛

➛ Sets clock ahead one hour.

➛➛

• To Make Corrections,
repeat steps 1) ~ 3).

Autumn (Last Sunday in October)

DST:ON

• If your area does not observe

• Keep these time changes in mind

➛➛

➛ Turns clock back one hour.

➛➛

Daylight Saving Time, select
DST:OFF.

when programming DECK for timer
recordings.

19

Playback/ Record on a Tape

Ready Checklist

All connections are made. (pp. 12 ~ 15)
TV and DECK are plugged in.
TV is on and tuned to CH 3, 4, or VIDEO.
Remote is in VCR mode. (Press VCR.)

➛ ➛

(

➛ The VCR mode Light-up Indicator lights on DECK)

➛ ➛

Playback a Tape

Insert a tape.

1

• DECK power comes on. If Auto VCR/TV (see
p. 34) is set to “OFF,” press VCR/TV on the
remote for VCR mode.

Press PLAY* to play a tape.

2

• If tape has no rec. tab (p. 6), auto play begins.

• The PLAY Light-up Indicator lights on DECK.

Special Features During Play

Forward/Reverse Scene Search

➛➛

➛ Press FF/SLOW+ or REW/SLOW-.

➛➛
➛➛

➛ Press PLAY to release.

➛➛

After search has begun, each additional press
of FF/SLOW+ or REW/SLOW- changes speed
as shown below.

[SP] : Approx. 5X ↔ Approx. 7X
[SLP] : Approx. 11X

↔ Approx. 21X

EJECT

VCR

FF/
SLOW+

REW/
SLOW-

PAUSE/
STILL

REC

VCR/TV

CH /

DVD

PLAY

STOP

SPEED

Notes

• Picture interruption may occur with some TVs.

• FF and REW search speed may vary depending

on current tape position.

• After 10 minutes in search mode, VCR returns to
Play mode to protect the tape and the video heads.

Still (Freeze) Picture

➛➛

➛ Press PAUSE/STILL.

➛➛
➛➛

➛ Press PLAY to release.

➛➛

Frame by Frame Picture

➛➛

➛ Press PAUSE/STILL in Still mode.

➛➛
➛➛

➛ Press PLAY to release.

➛➛

Slow Motion Picture

➛➛

➛ Press FF/SLOW+ (increase speed) or

➛➛

REW/SLOW- (decrease speed) in Still
mode.

➛➛

➛ Press PLAY to release.

➛➛

Press STOP to stop a tape.

3

Press REW/SLOW- or FF/SLOW+ in Stop
mode to rewind or fast forward a tape.

Press EJECT on remote,
or STOP/EJECT on DECK to eject a tape.

20

For assistance, please call : 1-800-211-PANA(7262) or, contact us via the web at:http://www.panasonic.com/contactinfo

Notes

• These features work best in SP or SLP mode.

• The sound will be muted.

• To reduce picture noise, see “Manual
Tracking Control” on page 4.

• After 3 minutes in Still or Slow mode, VCR

stops to protect the tape and the video heads.

Playback using DECK buttons

2

Press PLAY.

Press STOP/EJECT to stop
and/ or eject a tape.

1

Insert a tape.

Light-up Indicators

*Important: If a remote control button does not work when pressed,

press the VCR button on the remote and try the button again.

Record on a Tape

Insert a tape with a record tab (p. 6).

1

• DECK power comes on. If Auto VCR/TV (see p. 34)
is set to “OFF,” press VCR/TV on the remote for
VCR mode.

Press CH , or NUMBER keys

2

to select the channel.

• If channel number is over 100, first press 100 key
then the other 2 digits.

• For “LINE” input, see p. 35.

Press SPEED

to select the record speed (p. 4).

3

SP = Standard Play
SLP = Super Long Play

Press REC

to start recording.

4

(The VCR REC Light-up Indicator lights on DECK),

• To edit out unwanted scenes, press PAUSE/STILL
to pause, and again to resume recording.

• You cannot view another channel during recording.

This video recorder, equipped with HQ
(High Quality) system, is compatible
with existing VHS equipment.
Only use tapes with the mark.
Only tapes tested and inspected for
use in 2, 4, 6, and 8 hour machines
are recommended.

Basic Operation

Note

Remove loose or peeling labels
from tapes to prevent tape jam.

Press STOP

to stop recording.

5

One Touch Recording (recording in progress),

➛➛

➛ press REC repeatedly to set the recording length

➛➛

(30 min. ~ 4 hours) (see right).

• DECK shuts off after the preset record length.

Record one station, watch another,

➛➛

➛ press VCR/TV on the remote

➛➛

(change to TV mode),

➛➛

➛ select channels at TV (recording continues).

➛➛

Select Channels at DECK

(In Stop or Rec. Pause mode)

➛➛

➛ press VCR/TV on the remote

➛➛

(change to TV mode),

➛➛

➛ select channels at DECK.

➛➛

Play a disc while recording a tape.

➛➛

➛ insert a disc during recording,

➛➛
➛➛

➛ press

➛➛

Notes

• It is not possible to record from DVD/ Video CD/ CD
to VHS tape using DECK.

• Watching one channel and recording another is not
possible when using Cable Box or DSS Receiver.

• After 5 minutes in Pause mode, DECK stops to protect a
tape and video heads.

DVD

, and then press

PLAY

.

<One Touch Recording screen>

Normal Rec

Press REC repeatedly

0:30 1:00

1:302:003:004:00

Record using DECK buttons

4

Press REC
to start
recording.

Select

2

Channel.

Press STOP/EJECT to stop.

Insert a tape.

1

Light-up
Indicators

21

Basic DVD Operation

Ready Checklist

All connections are made. (pp. 12 ~ 15)
DECK is plugged in.
If DECK is connected to an audio amplifier,

turn the stereo system’s power on.

OPEN/
CLOSE

POWER

10

NUMBER
keys

SELECT

SET
FF/

SLOW+
REW/

SLOW­PAUSE/

STILL
TITLE

MENU

STOP
DVD

PLAY

SKIP+
SKIP

VSS

RETURN

Press

• The DVD mode Light-up Indicator lights on

1

• If a disc is already inserted, go to step 3.

Press

2

and then place a disc into the disc tray.

Press

3

Disc tray closes automatically.

-

If an interactive DVD*1 or
a Video CD with playback
control*2 is used and TITLE
MENU appears, go to step 4.

DVD

to select DVD mode.

DECK.

(Depending on the disc, playback may start
automatically.)

OPEN/CLOSE

PLAY

to start playing.

*,

• Hold disc by its edges
only (p. 6) with printed
side up and use guides
to place into tray.

1

Use 3” (8 cm)

2

• The PLAY Light-up Indicator
lights on DECK.

• You may also close tray by

pressing

• Data reading time differs with
each disc.

1

or 5” (12 cm) disc.

2

DVD-RAM ➡ see p. 42

OPEN/CLOSE

<Example1>

TITLE MENU

Cats

Samurai

Friend

Music

.

Operation using DECK buttons

3, 7

Press

1

POWER.

Insert a disc.

3

*1Interactive DVD...

May include multiple camera angles,
stories, etc.

*2Video CD with playback control...

Particular scenes or information can be
interactively selected from a menu that
appears on the screen.

4

Press
OPEN/CLOSE.

Press PLAY.

Press STOP.6

TITLE MENU

4

Using NUMBER keys starts play automatically.

The number of available titles varies with each disc.

<Input

Example>

Press
previous menu screen.

• SKIP function not available with all discs.
Please refer to disc jacket for operation information.

To return to menu (play stops)

Press
Press

5

6

Cats

Samurai

Friend

Music

<Example2>

1 digit number 1 •••• 1
2 digit number 12 ••• 10 ➛ 1 ➛ 2

SKIP+

Press

Press

| or

TITLE, MENU,
RETURN

STOP

OPEN/CLOSE

. (Video CD)

to stop playing.

Press or

NUMBER keys

below) to select title,
and press

SKIP-

or

RETURN

PLAY

• Pressing

to start playing.

is not necessary when
using

| to go to next or

NUMBER keys.

. (DVD)

to eject the disc.

SET

SET

or

(see

or

PLAY

22

For assistance, please call : 1-800-211-PANA(7262) or, contact us via the web at:http://www.panasonic.com/contactinfo