Panasonic PV-D4744 User Manual

DVD/VCR DECK
Operating Instructions
(Connection)
Initial Setup
Model No.
PV-D4744 / PV-D4744S
Connections and Initial Setup Procedures are on pages 12 to 17.
Operation
Basic
Operation
VCR
Operation
DVD
Information
For Your
MULTI FORMAT PLAYBACK
Ability to play back may depend on recording conditions.
*
As an ENERGY STAR Partner, Matsushita Electric Corporation of America has determined that this product or product model meets the ENERGY STAR guidelines for energy efficiency.
Please read these instructions carefully before attempting to connect, operate or adjust this product. Please save this manual. Spanish Quick Use Guide is included. (Guía para rápida consulta en español está incluida.)
For assistance, please call : 1-800-211-PANA(7262) or, contact us via the web at:http://www.panasonic.com/contactinfo
PV-D4744S P1-25 (040202).p65 2004/02/02, 13:211
®
®
LSQT0795 A
Important Safeguards and Precautions
TO REDUCE THE RISK OF ELECTRIC SHOCK, FIRE, INJURY TO PERSONS OR DAMAGE TO THIS PRODUCT, READ AND RETAIN ALL SAFETY AND OPERATING INSTRUCTIONS. HEED ALL WARNINGS IN THE MANUAL AND ON THE PRODUCT.
INSTALLATION
1 POWER SOURCE CAUTION
Operate only from a power source indicated on the unit or in this manual. If necessary, have your Electric Utility Service Company or Video Products Dealer verify the power source in your home.
2 POLARIZED OR GROUNDING PLUG
As a safety feature, this product comes with either a polarized power cord plug (one blade is wider than the other), or a three-
wire grounding type plug. POLARIZED PLUG CAUTION: This plug will only fit into an outlet one way. If you cannot fully insert the plug, try reversing it. If it still will not fit, have an electrician install the proper wall outlet. Do not defeat the safety feature by tampering with the plug. GROUNDING PLUG CAUTION: This plug will only fit into a three-hole grounding outlet. If necessary, have an electrician install the proper outlet. Do not defeat the safety feature by tampering with the plug.
3 POWER CORD
Make sure power cords are routed so that they are not likely to
have anything rest on them, roll over them, or be in the way of
walking traffic. If an extension cord is used, make sure it also
has either a polarized or grounded plug and that the cords can
be securely connected. Frayed cords, damaged plugs, and
damaged or cracked wire insulation are hazardous and should
be replaced by a qualified service technician.
Overloaded outlets and extension cords are fire hazards and
should be avoided.
4 DO NOT BLOCK VENTILATION HOLES
Ventilation openings in the cabinet release heat generated during
operation. If they are blocked, heat build-up inside the unit can
cause failures that may result in a fire hazard or heat damage to
cassettes or discs.
For protection, follow these rules:
a. Never cover ventilation slots or the unit while in use, or
operate the unit when placed on a bed, sofa, rug, or other soft surface.
b. Avoid built-in installation, such as a book case or rack,
unless proper ventilation is provided.
5 PLACEMENT: AVOID EXTREMELY HOT LOCATIONS OR
SUDDEN TEMPERATURE CHANGES
Do not place the unit over or near heater or radiator, in direct
sunlight, inside closed vehicles, in high temperature [over 104°F
(40°C)], or in over 75% humidity. If the unit is suddenly moved
from a cold place to a warm one, moisture may condense in the
unit and on the tape causing damage. Never subject the unit to
vibration, impact, or place it so that the surface is tilted as
internal parts may be seriously damaged.
6 TO AVOID PERSONAL INJURY
Do not place unsecured equipment on a sloping surface.
Do not place this unit on any support that is not firm, level, and adequately strong. The unit could fall causing serious injury to a child or adult and damage to the unit.
An appliance and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the appliance and cart combination to overturn.
Carefully follow all operating instructions and use the manufacturer's recommended accessories when operating this unit or connecting it to any other equipment.
2
1 SAFE ANTENNA AND CABLE CONNECTION
If an outside antenna or cable system is connected to the equipment, be sure the antenna or cable system is grounded so as to provide some protection against built up static charges and voltage surges. Section 810 of the National Electrical Code, ANSI/NFPA 70 (in Canada, part 1 of the Canadian Electrical Code) provides information with respect to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna discharge unit, connection to grounding electrodes and requirements for the grounding electrode.
2 KEEP ANTENNA CLEAR OF HIGH VOLTAGE POWER LINES OR
CIRCUITS
An outside antenna system should be located well away from power lines, electric light or power circuits and where it will never come into contact with these power sources if it should happen to fall. When installing an outside antenna, extreme care should be taken to avoid touching power lines, circuits or other power sources as this could be fatal. Because of the hazards involved, antenna installation should be left to a professional.
If the unit has been in storage or moved to a new location, refer first to the INSTALLATION section of these safeguards.
1 KEEP THE UNIT AWAY FROM WATER OR MOISTURE OF ANY KIND. 2 IF EQUIPMENT IS EXPOSED TO RAIN, MOISTURE, OR STRONG
IMPACT, unplug the unit and have it inspected by a qualified service technician
before use.
3 DURING AN ELECTRICAL STORM
During a lightning storm, whether indoors or outdoors, or before leaving the unit unused for extended periods of time, disconnect all equipment from the power source as well as the antenna and cable system.
4 WHEN THE UNIT IS PLUGGED IN
Never expose the unit to rain or water. DO NOT OPERATE if liquid has been spilled into the unit. Immediately unplug the unit, and have it inspected by a service technician. Fire and shock hazards can result from electrical shorts caused by liquid contact inside.
Never drop or push any object through openings in the unit. Some internal parts carry hazardous voltages and contact can cause electric shock or fire hazard. Do not put any foreign object on the disc tray.
Avoid placing the unit directly above or below your TV set as this may cause electrical interference. Keep all magnets away from electronic equipment.
5 USING ACCESSORIES
Use only accessories recommended by the manufacturer to avoid risk of fire, shock, or other hazards.
6 CLEANING THE UNIT
Unplug the unit. Then, use a clean, dry, chemically untreated cloth to gently remove dust or debris. DO NOT USE cleaning fluids, aerosols, or forced air that could over-spray, or seep into the unit and cause electrical shock. Any substance such as wax, adhesive tape, etc. may mar the cabinet surface. Exposure to greasy, humid, or dusty areas may adversely affect internal parts.
1 DO NOT SERVICE THIS PRODUCT YOURSELF
If, after carefully following the detailed operating instructions, this product does not operate properly, do not attempt to open or remove covers, or make any adjustments not described in the manual. Unplug the unit and contact a qualified service technician.
2 IF REPLACEMENT PARTS ARE REQUIRED
Make sure the service technician uses only parts specified by the manufacturer, or those having the same safety characteristics as the original parts. The use of unauthorized substitutes may result in fire, electric shock, or other hazards.
3 HAVE THE SERVICE TECHNICIAN PERFORM A SAFETY CHECK
After any service or repairs to the unit, request the service technician to conduct a thorough safety check as described in the manufacturers service literature to ensure that the unit is in safe operating condition.
OUTDOOR ANTENNA INSTALLATION
NEC - NATIONAL
ELECTRICAL CODE
ELECTRIC SERVICE EQUIPMENT
USING THE UNIT
SERVICE
GROUND CLAMP
ANTENNA LEAD IN WIRE
ANTENNA DISCHARGE UNIT (NEC SECTION 810-20)
GROUNDING CONDUCTORS (NEC SECTION 810-21)
GROUND CLAMPS
POWER SERVICE GROUNDING ELECTRODE SYSTEM (NEC ART 250, PART H)
PV-D4744S P1-25 (040202).p65 2004/02/02, 13:212
Safety Precautions/Mesures de sécurité
1
To prevent fire or shock hazard, do not expose this equipment to rain or moisture.
To prevent electric shock, match wide blade of plug to wide slot, fully insert.
AVERTISSEMENT:
Afin de prévenir tout risque dincendie ou de chocs électriques, ne pas exposer cet appareil à la pluie ou à une humidité excessive.
ATTENTION:
Pour éviter les chocs électriques, introduire la lame la plus large de la fiche dans la borne correspondante de la prise et pousser jusquau fond.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK)
NO USER-SERVICEABLE PARTS INSIDE
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL
This symbol warns the user that uninsulated voltage within the unit may have sufficient magnitude to cause electric shock. Therefore, it is dangerous to make any kind of contact with any inside part of this unit.
This symbol alerts the user that important literature concerning the operation and maintenance of this unit has been included. Therefore, it should be read carefully in order to avoid any problems.
CAUTION:
UNIT IS A CLASS I LASER PRODUCT. HOWEVER THIS UNIT USES A VISIBLE LASER BEAM WHICH COULD CAUSE HAZARDOUS RADIATION EXPOSURE IF DIRECTED. BE SURE TO OPERATE THE UNIT CORRECTLY AS INSTRUCTED.
WHEN THIS UNIT IS PLUGGED TO THE WALL OUTLET, DO NOT PLACE YOUR EYES CLOSE TO THE OPENING OF THE DISC TRAY AND OTHER OPENINGS TO LOOK INTO THE INSIDE OF THIS UNIT.
USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.
DO NOT OPEN COVERS AND DO NOT ATTEMPT TO REPAIR YOURSELF. REFER SERVICING TO QUALIFIED PERSONNEL.
CAUTION:
LASER RADIATION WHEN OPEN DO NOT STARE INTO BEAM.
ATTENTION:
RAYONNEMENT LASER EN CAS DOUVERTURE. NE PAS REGARDER DANS LE FAISCEAU.
(Inside of product)
FCC NOTE:
This equipment has been tested and found to comply with part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when operated in a residential environment. If this equipment does cause interference to radio or television reception, which can be determined by turning the equipment off and on, use the equipment in another location and/or utilize an electrical outlet different from that used by the receiver. If necessary, consult the dealer or an experienced radio/TV technician for help. The user may find the booklet, Something About Interference available from FCC local regional offices helpful.
FCC Caution:
To assure continued compliance, (example- use only shielded interface cables when connecting to other devices.) Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.
Region Management Information:
This DECK is designed and manufactured to respond to the Region Management Information that is recorded on a DVD disc. If the Region number described on the DVD disc does not correspond to the Region number of this DECK, this DECK cannot play this disc.
The Region number for this DECK is 1”.
The Player will play DVD-Video marked with labels
containing “1” or ALL”.
Example:
ALL
1
2
4
33
PV-D4744S P1-25 (040202).p65 2004/02/02, 13:213
Before Using
Congratulations
on your purchase of one of the most sophisticated and reliable products on the market today. Used properly, it will bring you years of enjoyment. Please fill in the information below. The serial number is on the tag located on the back of your DECK.
Date of Purchase
Dealer Purchased From
Dealer Address
Dealer Phone No.
Model No.
Serial No.
Accessories
Remote Control
EUR7724KA0
Loading the Batteries
Battery replacement caution
Do not mix old and new batteries.
Do not mix alkaline with manganese batteries.
Record/ Playback Time
Only use tapes with the mark in this DECK.
Tape Speed
Setting
SP
(Standard Play)
SLP
(Super Long Play)
4
For assistance, please call : 1-800-211-PANA(7262) or, contact us via the web at:http://www.panasonic.com/contactinfo
Type of Video Cassette
2 Hours
6 Hours 8 Hours
Batteries 2 AA
RF Coaxial Cable LSJA0418
To order accessories, call toll free 1-800-332-5368.
1) Open cover.
2) Insert batteries as marked.
3) Close cover.
T180T160T120
2 Hours
40 Minutes
3 Hours
9 Hours
Head Cleaning
Playing older or damaged tapes may eventually cause video heads to become clogged.
Video Head Clog Sensor
V I D
During playback, this screen appears if clogging is detected. To remove screen, press PLAY on the remote or DECK.
Use dry type head cleaning cassette only.
(Part No. NV-TCL30PT is recommended.)
Follow cleaning tape instructions carefully. Excessive use of tape can shorten head life.
If head clog symptoms persist, contact your nearest servicenter by visiting our Web Site (see p. 61).
EO HEADS MAY
N
EED
CLEAN I NG PLEASE I NSERT HEAD CLEAN I NG CASSETTE OR REFER
TO
MANUAL
END
: PL
AY
Cleaning DECK
Use a soft cloth or dusting attachment of a vacuum cleaner to remove dust from the ventilation holes on the back sides and bottom of the cabinet. Plastic surfaces are easily scratched and can be marred by alcohol and various solvents. Avoid excessive use of oil-based furniture polishes since the materials used in the cabinet will accumulate more dust. We recommend using a non-abrasive, antistatic cleaner and polisher.
Features for a Quality Picture (VCR)
Digital Auto Picture
Automatically controls the video output signal for less noise depending on the tape condition.
Digital Auto Tracking
Continuously analyzes the signal and adjusts for optimum picture quality.
Manual Tracking Control (to reduce picture noise)
Use during Playback and Slow Motion mode to reduce picture noise. Press CH (TRACKING) / on the remote control or on DECK until the picture clears up. To return to Auto Tracking, press POWER off, then on again a few seconds later.
R
R
R
R
V-Lock Control (to reduce picture jitter)
In Still mode, CH (TRACKING) / operate as a V-Lock control.
R
R
R
R
PV-D4744S P1-25 (040202).p65 2004/02/02, 13:214
Table of Contents
Initial Setup (Connection)
DVD / VCR
Important Safeguards and Precautions ......................... 2, 3
Before Using ......................................................................... 4
DECK & Cassette Information ........................................ 6 , 7
Location of Controls .................................................... 8 ~ 10
Displays (On Screen Displays and Multi Function Display) ................. 11
Connections ............................................................... 12 ~ 15
Initial Setup for Basic Connections (Ready to Play) ....... 16, 17
Basic Operation
VCR
Reset Language, Channels, Clock, VCR’s Output Channel .. 18, 19
Playback/ Record on a Tape........................................ 20, 21
DVD
Basic DVD Operation ................................................... 22, 23
VCR Operation
Timer Recording ........................................................... 24, 25
MTS Broadcast/ VHS Hi-Fi Stereo System ................. 26, 27
Multi-Brand Control Feature ........................................ 28, 29
Tape Operation (Search System) ...................................... 30, 31
Special VCR Features ................................................ 32 ~ 34
Copying Your Tapes (Dubbing) ...................................................... 35
(Connection)
Initial Setup
Operation
Basic
Operation
VCR
Operation
DVD
DVD Operation
Disc Operation ............................................................ 36 ~ 41
DVD-RAM Operation (DVD-RAM only) .............................. 42, 43
DVD Operation using On-Screen Displays .............. 44 ~ 48
MP3/JPEG Playback Operation ................................. 49 ~ 51
Settings for DVD Operation ....................................... 52 ~ 55
Language Code List ........................................................... 56
For Your Information
Warning and Instruction Displays..................................... 57
Before Requesting Service.......................................... 58, 59
Limited Warranty .......................................................... 60, 61
Customer Services Directory ............................................ 61
Spanish (Español) Quick Use Guide......................... 62 ~ 69
Index .............................................................................. 70, 71
PV-D4744S P1-25 (040202).p65 2004/02/02, 13:215
Information
For Your
5
DECK & Cassette Information
Prevent Accidental Tape Erasure
Break off the tab to prevent recording.
Record Tab
Screw driver
To record again
Cover the hole with cellophane tape.
Disc formats supported by this DECK
DECK can play back discs bearing any of the following marks:
Logo Disc type
DVD-RAM (Version 1.1 of the Video Recording Format a unified video recording standard)
DVD (DVD-Video)
DVD-R (DVD-Video formatted discs [finalized])
CD (CD-DA)
CD-R/CD-RW
CD-DA format
MP3/JPEG file
and finalized.*
[Discs Played 8cm (3") or 12cm (5")] *A process that allows play on compatible equipment.
Discs which cannot be played
DVD with Region No. other than “1” or “ALL”
PAL discs, DVD-ROM, DVD-Audio, DVD-RW,
DVD+R, DVD+RW, CD-ROM, CDV, CD-G, CVD, SVCD, SACD, CD-TEXT, Divx Video Disc, Photo-CD and Video CD
Notes
Do not use irregularly shaped discs (e.g. heart­shaped), as these can damage the unit.
It may not be possible to play CD-R, CD-RW, DVD-R and DVD-RAM in all cases due to the type of disc or condition of the recording.
6
For assistance, please call : 1-800-211-PANA(7262) or, contact us via the web at:http://www.panasonic.com/contactinfo
DVD-RAM discs
DVD-RAM discs must meet the following conditions for this unit to be able to play them.
Type
Capacity
Remove TYPE 2 and 4 discs from their cartridges
before use, then return them when you are finished. Read the instructions for the disc carefully.
Some parts of the disc, for example where one program
ends and another begins, may not play smoothly.
Non-cartridge discs
Discs that can be removed from
their cartridges (TYPE 2 and 4)
12 cm (5) 9.4 GB (double-sided) and 4.7 GB (single-sided)
8 cm (3) 2.8 GB (double-sided)
Disc Handling
Handling precautions
Sticking a label on the disc may impair DVD-R playback.
Do not attach sticker to discs. (Do not use discs with
exposed adhesive from tape or left over peeled-off stickers.)
Only hold disc by edges as shown below. Fingerprints, dirt and scratches can cause skipping and distortion.
Do not write on label side of disc.
Never use record cleaning
sprays, benzine, thinner, static electricity prevention liquids, or any other solvent.
Do not try to close disc tray when disc is not properly placed.
To clean disc surface
With a soft, damp (water only) cloth, gently wipe from the center hole to the outer edge as shown below. (Wiping in a circular pattern will scratch the surface.)
DVD-RAM, DVD-R : Clean only with the DVD-RAM disc cleaner available. Never use cloths or cleaners for CDs etc.
If disc is brought from a cold to a warm environment, moisture may form on the disc
Wipe away moisture with a soft, dry, lint-free cloth before using disc. (See above.)
Improper disc storage
Discs could be damaged if stored or left in areas:
exposed to direct sunlight.
that are humid or dusty.
near heat (i.e. heater, radiator, etc.).
Disc tray
Disc
PV-D4744S P1-25 (040202).p65 2004/02/02, 13:216
Specifications
Power Source: 120 V AC, 60 Hz Power Consumption: Power On: Approx. 28 watts, Power Off: Approx. 0.85 watts
Video Signal: EIA Standard NTSC color Video Recording System: 4 rotary heads helical scanning system
Audio Track: 1 track (Normal), 2 channel (Hi-Fi Audio Sound) Tuner Broadcast Channels: VHF 2 ~ 13, UHF 14 ~ 69 CABLE Channels: Midband A through I (14 ~ 22), Superband J through W (23 ~ 36)
Input/Output Terminal: Audio/Video Line Input/Output, RF Input/Output Input Terminal: Audio/Video Line Input (Front) Output Terminal: S-Video Output (DVD only), Component Video Output (DVD only)
Operating Temperature: 5 °C ~ 40 °C (41 °F ~ 104 °F) Operating Humidity: 10 % ~ 75 % Weight: 3.85 kg (8.5 lbs). Dimensions: 430 (W) x 95 (H) x 273 (D) mm
Discs Played (1) DVD-Video Disc 5 (12 cm) single-sided single-layer
DVD-RAM Disc 5 (12 cm) 9.4 GB (double-sided) and 4.7 GB (single-sided)
(2) Compact Disc 5 (12 cm) disc
(CD-DA) 3 (8 cm) disc (CD-R/CD-RW, MP3, JPEG)
Digital Audio Output: Digital Optical Connector Pickup: Wavelength: 655 nm (DVD), 790 nm (CD)
Note: Designs and specifications are subject to change without notice.
Hyperband AA ~ EEE (37 ~ 64), Lowband A-5 ~ A-1 (95 ~ 99) Special CABLE channel 5A (01), Ultraband 65 ~ 94, 100 ~ 125
Audio Output 2 (L), (R)
16-15/16 (W) x 3-3/4 (H) x 10-3/4 (D) inch
5 (12 cm) single-sided double-layer 5 (12 cm) double-sided double-layer (one layer per side) 3 (8 cm) single-sided single-layer 3 (8 cm) single-sided double-layer 3 (8 cm) double-sided double-layer (one layer per side)
3 (8 cm) 2.8 GB (double-sided)
Laser power: CLASS II
(Connection)
Initial Setup
Definition of Terms (DVD)
Angle: Some DVD discs feature scenes simultaneously shot from different angles.
Chapter Number:Titles are subdivided into numbered sections. You can quickly search for
DVD: A high-density optical disc on which high-quality pictures and sound have
Subtitles: Written dialogue which appears at the bottom of the screen. Time Number: The elapsed play time from the start of a disc or title. Use to quickly find
Title Number: For DVD discs with two or more titles, the title is numbered as title 1, title 2, etc. Track Number: Numbers assigned to tracks on CDs to allow specific tracks to be quickly
Apparatus Claims of U.S. Patent Nos. 4,631,603, 4,577,216, 4,819,098 and 4,907,093, licensed for limited viewing uses only.
This product incorporates copyright protection technology that is protected by method claims of certain U.S. Patents and other intellectual property rights owned by Macrovision Corporation and other rights owners. Use of this copyright protection technology must be authorized by Macrovision Corporation, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision Corporation. Reverse engineering or disassembly is prohibited.
PV-D4744S P1-25 (040202).p65 2004/02/02, 13:217
The ANGLE button can be used to view the scene from different angles. (ANGLE Indicator lights on DECK when a scene recorded at different angles is detected.)
a favorite scene using these numbers.
been digitally recorded. DVD incorporates video compression technology (MPEG II) and high-density recording technology which allow entire movies to be recorded with incredible playback quality.
scenes. (May not work with some discs.)
located.
7
Location of Controls
Remote Control
EJECT /
OPEN / CLOSE
pp. 20,
22
POWER
NUMBER keys
ADD/DELETE /
pp. 19,
39
ACTION
pp. 18
, 52
SET
VCR mode
p. 28
STOP
pp. 20,
22
REWIND /
SLOW-
pp. 20,
23
FAST FORWARD /
SEARCH / SLOW+
pp. 20,
23
PAUSE /
pp. 20,
23
ANGLE
p
. 37
SUB TITLE
p
. 36
TITLE
/
DIRECT NAVIGATOR
p
. 38, 42
CLEAR
SEARCH
STILL
Bold: VCR Function /
Italic
:
DVD Function
/
Bold Italic:VCR and DVD Functions
/ Normal: Others
TRACKING
CHANNEL
/
V-LOCK
pp. 4, 21,
VOLUME
MENU / PLAY LIST
DVD mode
Virtual Surround Sound (V.S.S.)
TAPE POSITION
VOLUME ADJUST
AUDIO
(SAP / Hi-Fi)
VCR/TV
TV mode
/ /
/
+
p
. 38, 43
SELECT
PLAY
pp. 20,
SKIP+
SKIP-
ENTER
pp.
ZOOM
/
STATUS
p. 31,
pp. 27,
p. 21
p. 28
/
p. 28
p.
p
23,
p
. 23
. 37
10
22
-
28
22
28
41
36
/
INPUT
p. 35
DISPLAY
p. 11,
44
RECORD
p. 21
SPEED
p. 21
EJECT button: When this button is pressed in VCR mode, the tape is ejected.
8
PV-D4744S P1-25 (040202).p65 2004/02/02, 13:218
For assistance, please call : 1-800-211-PANA(7262) or, contact us via the web at:http://www.panasonic.com/contactinfo
This button is inoperative if pressed during recording. If pressed in DVD mode, the disc tray opens or closes.
RETURN /
COMMERCIAL SKIP
COUNTER RESET
SEARCH
pp
. 22,
ZERO SEARCH
pp. 30
p. 30
PROGRAM
p. 24
30
/
Front View of DECK
Front View of DECK
Bold: VCR Function
Italic
:
DVD Function
:
Bold Italic
Normal: Others
PLAY
p. 20
VCR and DVD Functions
If the disc cannot be removed...
First, unplug DECK. Then, prepare a rigid wire (e.g. an extended paper clip) and, applying moderate force, insert it straight into the hole at the base of the tray. The tray will eject a little. Now, pull the tray all the way out and remove the disc.
(Connection)
Initial Setup
STOP/EJECT
p. 20
POWER
Audio/Video Input Connector 2 (LINE 2)
REC
p. 21
CHANNEL / TRACKING/V-LOCK
pp. 4, 21
p. 35
Reset All Memory Functions
Cassette Compartment
Multi Function
Display
p. 11
Remote Sensor
Over 2 inches
Disc Tray
OPEN/CLOSE
FAST FORWARD
/
SEARCH
REWIND /
SEARCH
SKIP
p. 20,
SKIP
p. 20,
PLAY
STOP
p.
22
/
23
/
23
p.
22
p.
22
Returns to factory setting. Use if relocating DECK, or if Initial Setup needs to be redone.
Make sure a tape is not inserted in the DECK.
Turn DECK Power on.
1
Press and hold both VCR PLAY
2
and CHANNEL on the DECK for more than 5 seconds.
The power shuts off. Perform Initial Setup (Ready to Play)
3
121
PV-D4744S P1-25 (040202).p65 2004/02/02, 13:219
on page 16.
9
Location of Controls (continued)
Rear View of DECK
AC Power Plug
While plugged into an AC outlet, this DECK consumes 0.85 W of electrical power in off mode.
Component Video Output Connector (Y, PB, PR) (DVD Only)
p.
13
Optical Digital Audio Output Connector (DVD Only)
p.
15
S-Video Out Connector (DVD Only)
pp.
10, 13
Bold: VCR Function
Bold Italic:VCR and DVD Functions
VHF/UHF Antenna Output Terminal p.12
VHF/UHF Antenna Input Terminal p. 12
Video Output Connector
p.
12
Video Input Connector p. 35
Audio Output 1 Connector (L/R)
p.
12
Audio Output 2 Connector (L/R)
p.
13
Audio Input Connector (L/R) p. 35
Italic:DVD Function
The following table shows the status of the output jacks when in VCR or DVD mode.
VCR
DVD
Video Output Audio Out 1 Audio Out 2
YES YES
Component Video Output
N/A
S-VIDEO OUT
N/A
YES
PROG functions on the remote are not available when using Component Video Output and
Note
S-VIDEO OUT. Please set TV to either RF INPUT or VIDEO INPUT, and then press PROG.
To enjoy PROGRESSIVE SCAN video
(1). Connect
(See p. 13.)
(2). When PROGRESSIVE OUT is set to ON in the DVD Main Menu (p. 55), a Progressive
Scan signal is output from the
Notes
The screen may shift off-center when using progressive output. Please adjust the screen position if this occurs. (Refer to your TV manual.)
If the television is not progressive compatible, a progressive scan picture is not available. Connect the Video Output or S-Video Output connector (see p. 12, 13) and set PROGRESSIVE OUT to OFF in the DVD Main Menu. (See p. 55.)
10
PV-D4744S P1-25 (040202).p65 2004/02/02, 13:2110
Component Video Output
For assistance, please call : 1-800-211-PANA(7262) or, contact us via the web at:http://www.panasonic.com/contactinfo
to the component video input terminals of a television.
Component Video Output Connector
.
Displays (On Screen & Multi Function)
On Screen Displays (VCR)
(Connection)
Initial Setup
Function & Channel Displays
CH 0 8
When a function button is pressed, e.g. PLAY, or you change channels, a 5-second display appears.
VCR Status & Clock Displays To display or remove screen shown at right,
➛➛
press DISPLAY.
➛➛
Multi Function Display
VCR mode Indicator
Lights up when DECK is in VCR mode.
Tape Indicator
Lights up when a tape is inserted.
Hi-Fi Indicator
Lights up when Hi-Fi audio is present in Play mode.
Function Status
Rec Time Remaining (OTR mode only, see p. 21.)
Broadcast Audio Being Received (See pp. 26, 27.)
VCR
Hi - Fi
ANGLE
Blank Tape/ No Video Signal Indications
Whenever a blank section of a tape comes up in Play mode, or when the selected channel has no broadcast signal with Weak Signal Display Feature (p. 33) set to OFF, the TV screen will turn solid blue.
Current Time
Channel
REW 0 : 25 STER SAP M
ONO
1 2 : 0 0A
EO
CH 02
M
-0 : 1 2 : 3 4 SP
Counter
Tape Speed (See p. 4.)
DVD mode Indicator
Lights up when DECK is in DVD mode.
DISC Indicator
Lights up when a disc is inserted.
VCR REC Indicator
Lights up during recording.
A M
DVD
REC
TIMER
ANGLE Indicator
Lights up when a scene recorded at different angles is detected. (See p. 37.) (DVD only)
Clock/ Status/ Channel/ Speed Display
Displays current time. Briefly displays DECK status when you press a function button, channel number or L1 or L2 when you select channel or line input, and recording speed when you press SPEED.
PV-D4744S P1-25 (040202).p65 2004/02/02, 13:2111
AM/PM Indicator
Timer Indicator
Lights up when DECK is set for Timer Recording, or when One Touch Recording (OTR) is used. Flashes when Timer Recording is set, but a tape has not been inserted into DECK and when a power interruption occurs during Timer Programming.
11
Connections
Basic Connections
If your TV has AUDIO and VIDEO IN terminals, connect them to DECK for higher
quality picture and sound.
You can enjoy stereo sound even if your TV is not stereo by connecting a stereo
amplifier to DECK.
Connect DECK and TV with an RF Coaxial Cable a (supplied) or an AV Cable (not supplied) as shown in the figure below.
DSS Receiver DECK TV
DECK TV
Antenna or Cable
Cable Box DECK TV
b
DSS Receiver
IN
IN
OUT
or
DVD/VCR DECK
IN FROM ANT.
IN 1
OUT
VIDEO
L
AUDIO
R
When using Nut type RF coaxial cables, tighten with fingers only. Overtightening may damage terminals.
VHF/UHF
OUT TO TV
IN
OUT
Cable Box
1 Disconnect antenna or cable from TV
and connect to DECK.
2 Connect DECK to TV with RF Coaxial Cable.
RF COAXIAL CABLE
a
TV
AUDIO IN
R
(supplied)
VIDEO
IN
L
b
AV CABLE
VHF/ UHF
(not supplied)
Note to CABLE system installer
This reminder is provided to call the CABLE system installers attention to Article 820-40 of the NEC in USA (and to the Canadian Electrical Code in Canada) that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical.
12
PV-D4744S P1-25 (040202).p65 2004/02/02, 13:2112
For assistance, please call : 1-800-211-PANA(7262) or, contact us via the web at:http://www.panasonic.com/contactinfo
Other Connections
With a Cable Box (DECK
DVD/VCR DECK
IN FROM ANT.
IN 1
OUT
VHF/UHF
OUT TO TV
■■
Connect With Two Cable Boxes
■■
ANT or CATV
Cable Box
Cable Box TV)
OUTIN
DVD/VCR DECK
ANT
or
CATV
Cable Box
OUT
IN
2-Way Splitter
OUT 1
OUT 2
OUT
Cable Box
OUTIN
IN 1
IN FROM ANT.
VHF/UHF
OUT TO TV
A/B Switch
VHF/ UHF
IN 2IN 1
view any (including
use Remote
record and view
TV
AUDIO
VIDEO
scrambled) channel.
Control to select channels without using Multi-brand control feature.
both scrambled and unscrambled channels if additional equipment is added. This connection requires: two converter boxes, an A/B switch, and a 2-way splitter.
TV
IN
OUT
R
AUDIO
L
VIDEO
IN
OUT
R L
VHF/ UHF
You CannotYou Can
record scrambled channels.
You CannotYou Can
view a channel other than the one selected for any type of recording.
set a Timer recording of a channel unless you select it on the Cable Box.
Connections For DVD Only (enjoying higher picture quality)
Connect AUDIO OUT2 (L, R) to the AUDIO IN (L, R) of the TV. (audio input for COMPONENT
1
or S-VIDEO mode). If your TV has COMPONENT VIDEO INPUT, connect to COMPONENT VIDEO OUT.
2
If your TV does not have COMPONENT VIDEO INPUT but has S-VIDEO INPUT, connect to S-VIDEO OUT.
When in DVD mode, set your TV to either COMPONENT VIDEO IN or S-VIDEO IN.
3
Notes
You can watch DVDs through the S-VIDEO or COMPONENT VIDEO, VHF/UHF OUT TO TV, and VIDEO OUT connections to your TV. The VCR and TUNER pictures are available only from the VIDEO OUT and VHF/UHF OUT TO TV connections to your TV.
PROG functions on the remote are not available when using S-VIDEO OUT and COMPONENT Video Output. Please set TV to either RF INPUT or VIDEO INPUT, and then press PROG.
TV must have capability to accept and display a progressive scan signal to use PROGRESSIVE mode. Consult your TV operating instructions.
DVD/VCR DECK
DVD OUTPUT
S-VIDEO OUT
COMPONENT
VIDEO OUT
Y
P
B
P R
AUDIO OUT2
L
R
Y
PB
PR
IN
L
L
R
R
TV
IN
AUDIO
VIDEO
S-VIDEO IN
From DECK’s
A/V OUTPUT
IN
(Connection)
Initial Setup
or
PV-D4744S P1-25 (040202).p65 2004/02/02, 13:2113
13
Connections (continued)
Audio Connections
Ready Checklist
Turn down the volume, then turn DECK, as well as other equipment to be connected, off before proceeding with connection. Do not block ventilation holes of any of the equipment and arrange them so that air can circulate freely. Read through the instructions before connecting other equipment. Ensure that you observe the color coding when connecting audio and video cables.
Connecting Amplifier (2ch stereo system)
DVD/VCR DECK
AUDIO OUT2
L
Speaker
Amplifier
AUDIO IN
R L
R
Enjoying digital audio output from the digital audio output connector
Notes on audio output from the optical digital audio output connector
Disc
DVD-Video
Sound recording format
Dolby Digital
Linear PCM (48/96 kHz 16/20/24 bit)
DTS
DVD-RAM
Dolby Digital
Linear PCM(48 kHz/16 bit)
CD MP3
*1 The type of audio output from the connector can be selected by the Settings for DVD
Operation. (See p. 53.)
*2 When LPCM(DVD)” is set to OFF in the DVD Main Menu, only 48 kHz sampling/16 bit is ouput.
When set to ON, sampling of sound quality greater than 48 kHz/16 bit is reduced to 48 kHz/16 bit. (See page 53.)
Linear PCM MP3
For your reference:
Dolby Digital is a digital sound compression technique developed by the Dolby Laboratories Licensing Corporation. Supporting 5.1-channel surround sound, as well as stereo (2-channel) sound, this technique enables a large quantity of sound data to be efficiently recorded on a disc.
Linear PCM is a signal recording format used in CDs. While CDs are recorded in 44.1 kHz/16 bit, DVDs are recorded in 48 kHz/16 bit up to 96 kHz/24 bit.
If you have a Dolby Pro Logic Surround decoder, you will obtain the full benefit of Pro Logic from the same DVD movies that provide full 5.1 channel Dolby Digital soundtracks, as well as from titles with the Dolby Surround mark. For information on Panasonic or Technics Dolby Pro Logic Surround Sound Decoders please contact your local dealer.
Manufactured under license from Digital Theater Systems, Inc. US Pat. Nos. 5,451,942, 5,956,674, 5,974,380, 5,978,762, 6,487,535 and other US. and world-wide patents issued and pending. DTS and DTS 2.0 + Digital Out are trademarks of Digital Theater Systems, Inc. Copyright 1996, 2003 Digital Theater Systems, Inc. All Rights Reserved.
Manufactured under license from Dolby Laboratories. Dolby,Pro Logic, and the double-D symbol are trademarks of Dolby Laboratories.
Optical digital audio output from connector
Dolby Digital bitstream (1 - 5.1 ch) or PCM (48 kHz sampling/16 bit only)*
Linear PCM (2 ch) (48 kHz sampling/16 bit only)*
Bitstream or PCM (48 kHz sampling/16 bit only)* Dolby Digital bitstream (1 - 5.1 ch)
or PCM (48 kHz sampling/16 bit only) Linear PCM (2 ch) Linear PCM (44.1 kHz sampling)
Linear PCM (It depends on the MP3 file)
Speaker
1
2
1
14
PV-D4744S P1-25 (040202).p65 2004/02/02, 13:2114
For assistance, please call : 1-800-211-PANA(7262) or, contact us via the web at:http://www.panasonic.com/contactinfo
Connecting Amplifier (5.1 ch Surround system) [Digital connection] DECK Dolby Digital Decoder Amplifier Speaker
or
DECK DTS (Digital Theater Systems) Decoder Amplifier Speaker
When DVDs recorded in Dolby Digital or DTS are played, Dolby Digital bitstream or DTS bitstream is output from the DECK OPTICAL digital audio output connector. When DECK is connected to a Dolby Digital decoder or DTS decoder, you can enjoy theater-quality audio in your home. [An optical digital audio cable (optional) is required when an optional Dolby Digital decoder or DTS decoder is used.]
Notes on connecting an optical digital audio cable (optional)
Firmly connect the cable to the connector.
(Connection)
Initial Setup
Surround Speaker
[5.1ch Surround system]
Surround Speaker
Center Speaker
DVD/VCR DECK (Rear)
Optical Digital Audio Cable (optional)
Caution for optical digital audio output connector:
When connecting an amplifier (with an Optical Digital Input Connector) which does not contain the Dolby Digital or DTS decoder, be sure to select “PCM” at “Dolby Digital” and PCM at dts” of the Settings for DVD Operation “Audio Output” (see p. 53). Otherwise, any attempt to play DVDs may cause such a high level of noise that it may be harmful to your ears and damage your speakers.
When a Dolby Digital/DTS decoder is connected, please select Bitstream at “dts orDolby Digital of the Settings for DVD Operation “Audio Output”. If PCM is selected, there will be stereo sound. (See p. 53.)
CDs can be played as usual.
Note:
Some DTS decoders which do not support DVD-DTS interface may not work properly with DECK.
Decoder with Dolby Digital /DTS processing (optional)
To Optical Digital Audio Input Connector
Front Speaker
Front Speaker
Amplifier
Subwoofer
15
PV-D4744S P1-25 (040202).p65 2004/02/02, 13:2115
Initial Setup for Basic Connections (Ready to Play)
Before doing Initial Setup
Turn TV on.
1
See connections a RF Coaxial Cable Connection and b AV Cable Connection on page 12.
2
<RF Coaxial Cable Connection> Set TV to channel 3.
<AV Cable Connection>
Set TV to VIDEO.
[DECK
3
Go to Initial Setup (Ready to Play). (See below.)
[Cable Box
Turn on Cable Box and set it to your Public Broadcasting Station (PBS) channel
If you use a DSS Receiver, it must be turned off.
Initial Setup (Ready to Play)
Press VCR on remote for VCR mode.
1
Plug DECK Power Cord into AC wall outlet. DECK comes on and auto channel and clock set starts.
2
If screen below does not appear, check DECK - TV connection and, if TV is tuned to
To change VCRs output channel, please see VCRs Output Channel on page 19.
➛➛
TV]
➛➛
➛➛
DECK
➛➛
in your time zone.
channel 3, try switching it to channel 4.
➛➛
TV], [DSS
➛➛
Plug VCR Power plug into an AC wall outlet.
➛➛
DECK
➛➛
➛➛
TV]
➛➛
CH AUTO SET PROCEEDING
CANCEL : STOP
AUTO CLOCK SET
PROCEEDING
CANCEL : STOP
16
PV-D4744S P1-25 (040202).p65 2004/02/02, 13:2116
For assistance, please call : 1-800-211-PANA(7262) or, contact us via the web at:http://www.panasonic.com/contactinfo
Notes
Function buttons are void during Initial Setup.
To eject a tape during Auto Set, press EJECT on remote
or STOP/EJECT twice on DECK. Then make settings manually. (See p. 18.)
If Auto Clock Set takes more than 30 minutes, press STOP and perform settings manually. (See p. 18.)
Continued on next page...
*Important: If a remote control button does not work when pressed,
press the VCR button on the remote and try the button again.
Settings are made automatically. When complete, this screen appears.
3
EJECT
If AUTO CLOCK SET IS INCOMPLETE
ACTION
SELECT
SET
VCR
appears, manually set clock (below).
AUTO CLOCK SET
IS
I NCOM
PLETE
PLEASE SET CLOCK BY PRESSING
ACT I ON KEY
Manual Clock Set
(Connection)
Initial Setup
STOP/EJECT
If Auto Clock Set was incomplete.
Press ACTION* on remote to display CLOCK screen.
1
SET CLOCK
1 / 1/2004
- - - - - - - - -- - - - - - - -- - - - - -
SELECT : END:
Press set. In the same manner, select and set
2
to select the month and SET to
THU
SET : SET
ACT I ON
-- -12:00 DST : O
PM
N
the date, year, time, and DST (Daylight Saving Time).
SET CLOCK
6 /20/2004
- - - - - - - - -- - - - - - - -- - - - - -
SELECT : START
Press ACTION to start clock and exit.
3
SUN
- -15:30
SET : SET
: ACT I ON
DST : O
PM
N
17
PV-D4744S P1-25 (040202).p65 2004/02/02, 13:2117
Reset Language, Channels, Clock, VCR’s O
SELECT : EXIT
: ACTION
SET : SET
MENU SET UP VCR
SET UP CLOCK
SET UP CHANNEL IDIOMA/LANGUE : ENGLISH VCRS OUTPUT CH:3
AUTO CLOCK SET
MANUNU
AL
T I M
E ZONE AD
JUS
T :
0
SET CLOCK
SELECT :
SET : SET
EXIT:
ACT I ON
DST : O
N
1 / 1/2004
THU
-- -12:00
PM
- - - - - - - - -- - - - - - - -- - - - - -
SET CLOCK
SELECT :
SET : SET
END:
ACT I ON
1
2
MENU
SET UP VCR
SET UP CLOCK SET UP CHANNEL IDIOMA/LANGUE : ENGLISH VCR’S OUTPUT CH:3
SELECT :
: ACTION
SET : SET
EXIT
Press ACTION*
to display MENU.
Language
1) Press to select
language item.
MENU SET UP VCR SET UP CLOCK SET UP CHANNEL
IDIOMA/LANGUE : ENGLISH
VCRS OUTPUT CH:3
SELECT : EXIT
2) Press SET repeatedly to
change language item as shown below.
MENU PREPARAR VCR FIJAR RELOJ FIJAR CANAL
LANGUE/LANGUAGE:ESPAÑOL
SALIDA DE VCR CANAL : 3
ELEGIR : SALIR
For Spanish
SET : SET
: ACTION
FIJAR : SET
: ACTION
For French
PROGRAM functions are not available when using COMPONENT Video Output and S-VIDEO OUT. Please set TV to either RF INPUT or VIDEO INPUT, and then press PROGRAM.
Channels
1) Press to select
SET UP CHANNEL, and press SET.
MENU SET UP VCR SET UP CLOCK
SET UP CHANNEL
IDIOMA/LANGUE : ENGLISH VCRS OUTPUT CH:3
SELECT :
: ACTION
:
CABLE
: ACT I ON
SET : SET
NNE
L
SPLAY : OFF
SET : SET
EXIT
2) Press to select
ANTENNA, then press SET to set your antenna system (“TV” or “CABLE.”)
SET UP CHA
ANT
ENNA
AUTO SET WEAK
S I GNAL D I
SELECT : EXIT
3) Press to select
AUTO SET, then press SET.
If you use a Cable Box, set it to the PBS channel in your time zone.
Clock
1) Press to select
SET CLOCK, and
press SET.
2) Press to select MANUAL, and press SET. (For Auto Clock Set, select AUTO CLOCK SET.)
(TIME ZONE ADJUST
appears only when auto clock is set.)
MENU SET UP VCR SET UP CLOCK SET UP CHANNEL
IDIOMA/LANGUE : ENGLISH
VCRS OUTPUT CH:3
SELECT : EXIT
3) Press ACTION to exit.
18
PV-D4744S P1-25 (040202).p65 2004/02/02, 13:2118
For assistance, please call : 1-800-211-PANA(7262) or, contact us via the web at:http://www.panasonic.com/contactinfo
SET : SET
: ACTION
For English
CH AUTO SET PROCEEDING
CANCEL : STOP
After Channel Auto Set is finished, Auto Clock Set will be performed.
3) Press and to
select, then set the date, time, and DST (Daylight Saving Time).
4) Press ACTION to start
Clock and exit this mode.
C
HANNEL
08 ADDED
C
HANNEL
08 DELE T
ED
*Important: If a remote control button does not work
when pressed, press the VCR button on the remote and try the button again.
Time Zone Adjust
(Only when Auto Clock is set.)
1) Press to select
SET CLOCK, and press SET.
MENU SET UP VCR
SET UP CLOCK
SET UP CHANNEL IDIOMA/LANGUE : ENGLISH VCRS OUTPUT CH:3
SELECT :
: ACTION
SET : SET
EXIT
VCRs Output Channel
1) Press to select
VCRS OUTPUT CH., and press SET.
MENU SET UP VCR SET UP CLOCK SET UP CHANNEL IDIOMA/LANGUE : ENGLISH
VCRS OUTPUT CH:3
SELECT :
: ACTION
SET : SET
EXIT
POWER NUMBER
keys CH /
ADD/DLT ACTION SELECT
SET VCR
Operation
Basic
2) Press to select
TIME ZONE ADJUST,
SET CLOCK
AUTO CLOCK SET MANU
AL
T I M
E ZONE AD
JUS
T :
0
SELECT :
SET : SET
EXIT
: ACT I ON
and press SET to subtract or add hour(s) as necessary.
3) Press ACTION.
•“TIME ZONE ADJUST returns to “0” if clock is set manually.
2) Press SET.
I F YOU PRESS KEY, VCR SW I
TCHES TO
ACT I O
S OUTPUT CH
CH 4.
N
3) Press ACTION.
PLEASE TUNE YOUR TV TO CH 4.
After 3 seconds
MENU SET UP VCR SET UP CLOCK SET UP CHANNEL IDIOMA/LANGUE : ENGLISH
VCRS OUTPUT CH:4
SELECT :
: ACTION
SET : SET
EXIT
To Make Corrections, repeat steps 1) ~ 3).
Add or Delete a Channel
To add channel: Select channel with NUMBER keys
and press ADD/DLT.
To delete channel: Select channel with CH / or
NUMBER keys and press ADD/DLT.
DST (Daylight Saving Time)
DECK auto adjusts clock for DST. (p. 17.)
Spring (First Sunday in April)
DST:ON
Autumn (Last Sunday in October)
DST:ON
If your area does not observe
Keep these time changes in mind
➛➛
Sets clock ahead one hour.
➛➛
➛➛
Turns clock back one hour.
➛➛
Daylight Saving Time, select DST:OFF.
when programming DECK for timer recordings.
19
PV-D4744S P1-25 (040202).p65 2004/02/02, 13:2119
Playback/ Record on a Tape
Ready Checklist
All connections are made. (pp. 12 ~ 15) TV and DECK are plugged in. TV is on and tuned to CH 3, 4, or VIDEO. Remote is in VCR mode. (Press VCR.)
Playback a Tape
Insert a tape.
1
DECK power comes on. If Auto VCR/TV (see p. 32) is set to “OFF,” press VCR/TV on the remote for VCR mode.
Press PLAY* to play a tape.
2
If tape has no rec. tab (p. 6), auto play begins.
Special Features During Play
Forward/Reverse Scene Search
➛➛
Press FF/SLOW+ or REW/SLOW-.
➛➛ ➛➛
Press PLAY to release.
➛➛
After search has begun, each additional press of
FF or REW changes speed
Notes
Picture interruption may occur with some TVs.
FF and REW search speed may vary depending
on current tape position.
After 10 minutes in search mode, VCR returns to Play mode to protect the tape and the video heads.
Still (Freeze) Picture
➛➛
Press PAUSE/STILL.
➛➛ ➛➛
Press PLAY to release.
➛➛
Frame by Frame Picture
➛➛
Press PAUSE/STILL in Still mode.
➛➛ ➛➛
Press PLAY to release.
➛➛
Slow Motion Picture
➛➛
Press FF/SLOW+ (increase speed) or
➛➛
REW/SLOW- (decrease speed) in Still mode.
➛➛
Press PLAY to release.
➛➛
.
EJECT
VCR
FF/ SLOW+
REW/ SLOW-
PAUSE/ STILL
REC
Notes
These features work best in SP or SLP mode.
The sound will be muted.
To reduce picture noise, see Manual Tracking Control on page 4.
After 3 minutes in Still or Slow mode, VCR
stops to protect the tape and the video heads.
VCR/TV
CH /
DVD
PLAY
STOP
SPEED
Playback using DECK buttons
1
Insert a tape.
2
Press PLAY.
Press STOP to stop a tape.
3
Rapid Rewind/FF
Press REW/SLOW- or FF/SLOW+ in Stop mode to rewind or fast forward a tape.
Rewinds a T-120 tape in approx. 1 minute.
Press EJECT on remote, or STOP/EJECT on DECK to eject a tape.
20
PV-D4744S P1-25 (040202).p65 2004/02/02, 13:2120
For assistance, please call : 1-800-211-PANA(7262) or, contact us via the web at:http://www.panasonic.com/contactinfo
Multi Function Display
Press STOP/EJECT to stop and/ or eject a tape.
*Important: If a remote control button does not work when pressed,
REC T I ME : 0 :
30
T
I
ME : PRESS REC KEY
CANCEL : PRESS STOP KEY
CH 02
0
: 0 0 : 0
0
SP
press the VCR button on the remote and try the button again.
Record on a Tape
Insert a tape with a record tab (p. 6).
1
DECK power comes on. If Auto VCR/TV (see p. 32) is set to “OFF,” press VCR/TV on the remote for VCR mode.
Press CH , or NUMBER keys
2
to select the channel.
If channel number is over 100, first press 100 key then the other 2 digits.
For LINE input, see p. 35.
Press SPEED
to select the record speed (p. 4).
3
SP = Standard Play SLP = Super Long Play
Speed appears on-screen and on Multi Function Display.
Press REC
to start recording.
4
(The VCR REC indicator lights up on Multi Function Display),
To edit out unwanted scenes, press PAUSE/STILL to pause, and again to resume recording.
You cannot view another channel during recording.
Press STOP
to stop recording.
5
One Touch Recording (recording in progress),
➛➛
press REC repeatedly to set the recording length
➛➛
(30 min. ~ 4 hours) (see right).
DECK shuts off after the preset record length.
Record one station, watch another,
➛➛
press VCR/TV on the remote
➛➛
(change to TV mode),
➛➛
select channels at TV (recording continues).
➛➛
Select Channels at DECK (In Stop or Rec. Pause mode)
➛➛
press VCR/TV on the remote
➛➛
(change to TV mode),
➛➛
select channels at DECK.
➛➛
Play a disc while recording a tape.
➛➛
insert a disc during recording,
➛➛ ➛➛
press
➛➛
DVD
, and then press
PLAY
.
This video recorder, equipped with HQ (High Quality) system, is compatible with existing VHS equipment. Only use tapes with the mark. Only tapes tested and inspected for use in 2, 4, 6, and 8 hour machines are recommended.
Note
Remove loose or peeling labels from tapes to prevent tape jam.
<One Touch Recording screen>
Normal Rec
0:30 1:00
1:302:003:004:00
Record using DECK buttons
4
Press REC to start recording.
Insert a tape.
1
Operation
Basic
Notes
It is not possible to record from DVD/ CD to VHS tape using DECK.
Watching one channel and recording another is not possible when using Cable Box or DSS Receiver.
After 5 minutes in Pause mode, DECK stops to protect a tape and video heads.
PV-D4744S P1-25 (040202).p65 2004/02/02, 13:2121
Select
2
Channel.
Multi Function Display
Press STOP/EJECT to stop.
21
Basic DVD Operation
Ready Checklist
All connections are made. (pp. 12 ~ 15) DECK is plugged in. If DECK is connected to an audio amplifier,
turn the stereo systems power on.
1
2 3
OPEN/ CLOSE
POWER
10
NUMBER keys
SELECT
SET FF/
SLOW+ REW/
SLOW­PAUSE/
STILL TITLE
MENU
STOP DVD
PLAY
SKIP+ SKIP
-
VSS
RETURN
4
If an interactive DVD*1 is used and TITLE MENU appears, go to step 5.
5
Operation using DECK buttons
Press
Press
1
POWER.
3
Insert a disc.
3, 7
OPEN/CLOSE.
Press PLAY.
4
Press STOP.6
Using NUMBER keys starts play automatically.
The number of available titles varies with each disc.
<Input
Example>
Press previous menu screen.
SKIP function not available with all discs.
To return to menu (play stops)
Press
6
*1Interactive DVD...
May include multiple camera angles, stories, etc.
7
Press
POWER*
Press
DVD
If a disc is already inserted, go to step 4. (Depending on the disc, playback may start automatically.)
Press
OPEN/CLOSE
and then place a disc into the disc tray.
Press
PLAY
Disc tray closes automatically.
CLOSE
READING
<Example2>
SKIP+
| or
Please refer to disc jacket for operation information.
TITLE, MENU,
Press
STOP
Press
OPEN/CLOSE
on the remote or DECK.
to select DVD mode.
,
Hold disc by its edges only (p. 6) with printed side up and use guides to place into tray.
1
Use 3 (8 cm)
2
to start playing.
You may also close tray by
pressing
Data reading time differs with each disc.
1 digit number 1 •••• 1 2 digit number 12 ••• 10 1 2
SKIP-
or
RETURN
to stop playing.
1
or 5 (12 cm) disc.
2
DVD-RAM see p. 42
OPEN/CLOSE
<Example1>
T I TLE MENU
Cas t l es
Dogs
i r
SET
SET
r
s
or
B
(see
or
PLAY
Love
Press or
NUMBER keys
below) to select title, and press
PLAY
to start playing.
Pressing is not necessary when using
NUMBER keys.
| to go to next or
.
to eject the disc.
.
ds
22
PV-D4744S P1-25 (040202).p65 2004/02/02, 13:2122
For assistance, please call : 1-800-211-PANA(7262) or, contact us via the web at:http://www.panasonic.com/contactinfo
Loading...
+ 50 hidden pages