Panasonic PVD4743S DoubleFeature OmniVision VHS, PVD4743 DoubleFeature OmniVision VHS User Manual [es]

Download

DVD/VCR DECK

Operating Instructions

(Connection)

Initial Setup

Model No. PV-D4743

PV-D4743S

Connections and Initial Setup Procedures are on pages 12 to 17.

Operation

Basic

Operation

VCR

Operation

DVD

MULTI FORMAT PLAYBACK

Ability to play back may depend on recording conditions.

As an ENERGY STAR Partner, Matsushita Electric Corporation of America has determined that this product or product model meets the ENERGY STAR guidelines for energy efficiency.

Please read these instructions carefully before attempting to connect, operate or adjust this product. Please save this manual. Spanish Quick Use Guide is included. (Guía para rápida consulta en español está incluida.)

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : consumerproducts@panasonic.com

D4743-4743S P1-25 (030318 C-lot).p65 2003/03/18, 15:281

LSQT0674C

Information

For Your

Important Safeguards and Precautions

FOR YOUR SAFETY, READ AND RETAIN ALL SAFETY AND OPERATING INSTRUCTIONS. HEED ALL WARNINGS IN THE MANUAL AND ON THE UNIT

INSTALLATION

1 POWER SOURCE CAUTION

Operate only from a power source indicated on the unit or in this manual. If necessary, have your Electric Utility Service Company or Video Products Dealer verify the power source in your home.

2 POLARIZED OR GROUNDING PLUG

As a safety feature, this product comes with either a polarized power cord plug (one blade is wider

than the other), or a three-wire grounding type plug. POLARIZED PLUG CAUTION: This plug will only fit into an outlet one way. If you cannot

fully insert the plug, try reversing it. If it still will not fit, have an electrician install the proper wall outlet. Do not defeat the safety feature by tampering with the plug.

GROUNDING PLUG CAUTION: This plug will only fit into a three-hole grounding

outlet. If necessary, have an electrician install the proper outlet. Do not defeat the safety feature by tampering with the plug.

3 POWER CORD

Make sure power cords are routed so that they

are not likely to have anything rest on them, roll

over them, or be in the way of walking traffic.

If an extension cord is used, make sure it also

has either a polarized or grounded plug and that

the cords can be securely connected.

Frayed cords, damaged plugs, and damaged or

cracked wire insulation are hazardous and should

be replaced by a qualified service technician.

Overloaded outlets and extension cords are fire

hazards and should be avoided.

4 DO NOT BLOCK VENTILATION HOLES

Ventilation openings in the cabinet release heat

generated during operation. If they are blocked,

heat build-up inside the unit can cause failures that

may result in a fire hazard or heat damage to

cassettes or discs.

For protection, follow these rules:

a. Never cover ventilation slots or the unit while in

use, or operate the unit when placed on a bed, sofa, rug, or other soft surface.

b. Avoid built-in installation, such as a book case

or rack, unless proper ventilation is provided.

5 PLACEMENT: AVOID EXTREMELY HOT LOCATIONS

OR SUDDEN TEMPERATURE CHANGES

Do not place the unit over or near heater or

radiator, in direct sunlight, inside closed vehicles,

in high temperature [over 104°F (40°C)], or in over

75% humidity. If the unit is suddenly moved from

a cold place to a warm one, moisture may

condense in the unit and on the tape causing

damage. Never subject the unit to vibration,

impact, or place it so that the surface is tilted as

internal parts may be seriously damaged.

6 TO AVOID PERSONAL INJURY

• Do not place unsecured equipment on a sloping surface.

• Do not place this unit on any support that is not firm, level, and adequately strong. The unit could fall causing serious injury to a child or adult and damage to the unit.

• An appliance and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the appliance and cart combination to overturn.

• Carefully follow all operating instructions and use the manufacturer's recommended accessories when operating this unit or connecting it to any other equipment.

1 SAFE ANTENNA AND CABLE CONNECTION

If an outside antenna or cable system is connected to the equipment, be sure the antenna or cable system is grounded so as to provide some protection against built up static charges and voltage surges. Section 810 of the National Electrical Code, ANSI/NFPA 70 (in Canada, part 1 of the Canadian Electrical Code) provides information with respect to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna discharge unit, connection to grounding electrodes and requirements for the grounding electrode.

KEEP ANTENNA CLEAR OF HIGH VOLTAGE POWER LINES OR CIRCUITS

An outside antenna system should be located well away from power lines, electric light or power circuits and where it will never come into contact with these power sources if it should happen to fall. When installing an outside antenna, extreme care should be taken to avoid touching power lines, circuits or other power sources as this could be fatal. Because of the hazards involved, antenna installation should be left to a professional.

If the unit has been in storage or moved to a new location, refer first to the INSTALLATION section of these safeguards.

KEEP THE UNIT AWAY FROM WATER OR MOISTURE OF ANY KIND.

2 IF EQUIPMENT IS EXPOSED TO RAIN, MOISTURE, OR

STRONG IMPACT, unplug the unit and have it inspected by a

qualified service technician before use.

3 DURING AN ELECTRICAL STORM

During a lightning storm, whether indoors or outdoors, or before leaving the unit unused for extended periods of time, disconnect all equipment from the power source as well as the antenna and cable system.

4 WHEN THE UNIT IS PLUGGED IN

• Never expose the unit to rain or water. DO NOT OPERATE

• Never drop or push any object through openings in the unit.

• Avoid placing the unit directly above or below your TV set

5 USING ACCESSORIES

Use only accessories recommended by the manufacturer to avoid risk of fire, shock, or other hazards.

6 CLEANING THE UNIT

Unplug the unit. Then, use a clean, dry, chemically untreated cloth to gently remove dust or debris. DO NOT USE cleaning fluids, aerosols, or forced air that could over-spray, or seep into the unit and cause electrical shock. Any substance such as wax, adhesive tape, etc. may mar the cabinet surface. Exposure to greasy, humid, or dusty areas may adversely affect internal parts.

1 DO NOT SERVICE THIS PRODUCT YOURSELF

If, after carefully following the detailed operating instructions, this product does not operate properly, do not attempt to open or remove covers, or make any adjustments not described in the manual. Unplug the unit and contact a qualified service technician.

2 IF REPLACEMENT PARTS ARE REQUIRED

Make sure the service technician uses only parts specified by the manufacturer, or those having the same safety characteristics as the original parts. The use of unauthorized substitutes may result in fire, electric shock, or other hazards.

HAVE THE SERVICE TECHNICIAN PERFORM A SAFETY CHECK

After any service or repairs to the unit, request the service technician to conduct a thorough safety check as described in the manufacturer’s service literature to ensure that the unit is in safe operating condition.

OUTDOOR ANTENNA INSTALLATION

NEC

- NATIONAL ELECTRICAL CODE

ELECTRIC SERVICE EQUIPMENT

USING THE UNIT

if liquid has been spilled into the unit. Immediately unplug the unit, and have it inspected by a service technician. Fire and shock hazards can result from electrical shorts caused by liquid contact inside.

Some internal parts carry hazardous voltages and contact can cause electric shock or fire hazard. Do not put any foreign object on the disc tray.

as this may cause electrical interference. Keep all magnets away from electronic equipment.

SERVICE

GROUND CLAMP

ANTENNA LEAD IN WIRE

ANTENNA DISCHARGE UNIT (NEC SECTION 810-20)

GROUNDING CONDUCTORS (NEC SECTION 810-21)

GROUND CLAMPS

POWER SERVICE GROUNDING ELECTRODE SYSTEM (NEC ART 250, PART H)

D4743-4743S P1-25 (030318 C-lot).p65 2003/03/18, 15:282

Safety Precautions/Mesures de sécurité

WARNING: To prevent fire or shock hazard, do not expose this

equipment to rain or moisture.

CAUTION: To prevent electric shock, match wide blade of plug to

wide slot, fully insert.

Avertissement: Afin de prévenir tout risque d’incendie ou de chocs

électriques, ne pas exposer cet appareil à la pluie ou à une humidité excessive.

Attention: Pour éviter les chocs électriques, introduire la lame la

plus large de la fiche dans la borne correspondante de la prise et pousser jusqu’au fond.

This symbol warns the user that uninsulated voltage

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK)

NO USER-SERVICEABLE PARTS INSIDE

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL

within the unit may have sufficient magnitude to cause electric shock. Therefore, it is dangerous to make any kind of contact with any inside part of this unit.

This symbol alerts the user that important literature concerning the operation and maintenance of this unit has been included. Therefore, it should be read carefully in order to avoid any problems.

CAUTION:

UNIT IS A CLASS I LASER PRODUCT. HOWEVER THIS UNIT USES A VISIBLE LASER BEAM WHICH COULD CAUSE HAZARDOUS RADIATION EXPOSURE IF DIRECTED. BE SURE TO OPERATE THE UNIT CORRECTLY AS INSTRUCTED.

WHEN THIS UNIT IS PLUGGED TO THE WALL OUTLET, DO NOT PLACE YOUR EYES CLOSE TO THE OPENING OF THE DISC TRAY AND OTHER OPENINGS TO LOOK INTO THE INSIDE OF THIS UNIT.

USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.

DO NOT OPEN COVERS AND DO NOT ATTEMPT TO REPAIR YOURSELF. REFER SERVICING TO QUALIFIED PERSONNEL.

FCC NOTE:

This equipment has been tested and found to comply with part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when operated in a residential environment. If this equipment does cause interference to radio or television reception, which can be determined by turning the equipment off and on, use the equipment in another location and/or utilize an electrical outlet different from that used by the receiver. If necessary, consult the dealer or an experienced radio/TV technician for help. The user may find the booklet, “Something About Interference” available from FCC local regional offices helpful.

FCC Caution:

To assure continued compliance, (example- use only shielded interface cables when connecting to other devices.) Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.

FCC Warning: Any unauthorized changes or modifications to this equipment would void the user’s

authority to operate.

CAUTION:

LASER RADIATION WHEN OPEN DO NOT STARE INTO BEAM.

ATTENTION:

RAYONNEMENT LASER EN CAS D’OUVERTURE. NE PAS REGARDER DANS LE FAISCEAU.

(Inside of product)

Region Management Information:

This DECK is designed and manufactured to respond to the Region Management Information that is recorded on a DVD disc. If the Region number described on the DVD disc does not correspond to the Region number of this DECK, this DECK cannot play this disc.

● The Region number for this DECK is “1”.

● The Player will play DVD-Video marked with labels

containing “1” or “ALL”.

Example:

ALL

D4743-4743S P1-25 (030318 C-lot).p65 2003/03/18, 15:283

Before Using

Congratulations

on your purchase of one of the most sophisticated and reliable products on the market today. Used properly, it will bring you years of enjoyment. Please fill in the information below. The serial number is on the tag located on the back of your DECK.

• Date of Purchase

• Dealer Purchased From

• Dealer Address

• Dealer Phone No.

• Model No.

• Serial No.

Accessories

Remote Control

LSSQ0374 (PV-D4743) LSSQ0375 (PV-D4743S)

Batteries 2 “AA”

RF Coaxial Cable LSJA0372

To order accessories, call toll free 1-800-332-5368.

Loading the Batteries

1) Open cover.

2) Insert batteries as marked.

3) Close cover.

Battery replacement caution

• Do not mix old and new batteries.

• Do not mix alkaline with manganese

batteries.

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : consumerproducts@panasonic.com

Disc formats supported by this DECK

DECK can play back discs bearing any of the following marks:

Logo Disc type

Discs which cannot be played

• DVD with Region No. other than “1” or “ALL”

• DVD of PAL system, DVD-Audio, DVD-RAM, DVD-ROM,

DVD-RW, DVD+RW, CD-ROM, CDV, CD-G, CVD, SVCD, SACD, Divx Video Disc and Photo-CD

[Discs Played 8cm (3") or 12cm (5")]

DVD (DVD-Video) DVD-R (DVD-Video formatted

discs [finalized]) Video CD CD (CD-DA)

CD-R/CD-RW (CD-DA,Video CD formatted discs [finalized]) WMA, MP3, JPEG

Notes

• Do not use irregularly shaped discs (e.g. heartshaped), as these can damage the unit.

• It may not be possible to play CD-R, CD-RW and DVD-R in all cases due to the type of disc or condition of the recording.

Disc Handling

Handling precautions

• Sticking a label on the disc may impair DVD-R playback.

• Do not attach sticker to discs. (Do not use discs with exposed adhesive from tape or left over peeled-off stickers.)

• Only hold disc by edges as shown below. Fingerprints, dirt and scratches can cause skipping and distortion.

• Do not write on label side of disc.

• Never use record cleaning sprays, benzine, thinner,

static electricity prevention liquids, or any other solvent.

Disc tray

Disc

• Do not try to close disc tray when disc is not properly placed.

To clean disc surface

With a soft, damp (water only) cloth, gently wipe from the center hole to the outer edge as shown below. (Wiping in a circular pattern will scratch the surface.)

If disc is brought from a cold to a warm environment, moisture may form on the disc

Wipe away moisture with a soft, dry, lint-free cloth before using disc. (See above.)

Improper disc storage

Discs could be damaged if stored or left in areas:

• exposed to direct sunlight.

• that are humid or dusty.

• near heat (i.e. heater, radiator, etc.).

D4743-4743S P1-25 (030318 C-lot).p65 2003/03/18, 15:284

Table of Contents

DVD / VCR

Important Safeguards and Precautions ............................ 2, 3

Before Using ............................................................................ 4

DECK & Cassette Information ........................................... 6 , 7

Location of Controls ....................................................... 8 ~ 10

Displays (On Screen Displays and Multi Function Display) .................... 11

Connections .................................................................. 12 ~ 15

Initial Setup for Basic Connections (Ready to Play) .......... 16, 17

VCR Reset Language, Channels, Clock, VCR’s Output Channel ... 18, 19

Playback/ Record on a Tape........................................... 20, 21

DVD

Basic DVD Operation ...................................................... 22, 23

Timer Recording.............................................................. 24, 25

MTS Broadcast/ VHS Hi-Fi Stereo System .................... 26, 27

Multi-Brand Control Feature ........................................... 28, 29

Tape Operation (Search System) ....................................... 30 ~ 32

Special VCR Features ..................................................... 33, 34

Copying Your Tapes (Dubbing) ......................................................... 35

(Connection)

Initial Setup

Operation

Basic

Operation

VCR

Disc Operation ............................................................... 36 ~ 40

DVD Operation using On-Screen Displays ................. 41 ~ 42

MP3/WMA/JPEG Playback Operation .......................... 43 ~ 45

DVD Lock Feature ................................................................. 46

Settings for DVD Operation .......................................... 47 ~ 49

Language Code List.............................................................. 50

DVD / VCR

Warning and Instruction Displays........................................ 51

Before Requesting Service............................................. 52, 53

Limited Warranty ............................................................. 54, 55

Customer Services Directory ............................................... 55

Spanish (Español) Quick Use Guide............................ 56 ~ 61

Index ................................................................................. 62, 63

D4743-4743S P1-25 (030318 C-lot).p65 2003/03/18, 15:285

Operation

DVD

Information

For Your

DECK & Cassette Information

Head Cleaning

Playing older or damaged tapes may eventually cause video heads to become clogged.

Video Head Clog Sensor

During playback, this screen appears if clogging is detected. To remove screen, press PLAY on the remote or DECK.

• Use “dry” type head cleaning cassette only. (Part No. NV-TCL30PT is recommended.)

• Follow cleaning tape instructions carefully. Excessive use of tape can shorten head life.

• If head clog symptoms persist, contact your nearest servicenter by visiting our Web Site (see p. 55).

V I D

EO HEADS MAY

EED

CLEAN I NG PLEASE I NSERT HEAD CLEAN I NG CASSETTE OR REFER

MANUAL

END

: PL

Prevent Accidental Tape Erasure

Break off the tab to prevent recording.

Record Tab

Screw driver

To record again

Cover the hole with cellophane tape.

Record/ Playback Time

Only use tapes with the mark in this DECK.

Tape Speed

Setting

(Standard Play)

(Long Play)

SLP

(Super Long Play)

Type of Video Cassette

T160T120T60

1 Hour 2 Hours

2 Hours 4 Hours

2 Hours

40 Minutes

5 Hours

20 Minutes

3 Hours 6 Hours 8 Hours

Cleaning DECK

Use a soft cloth or dusting attachment of a vacuum cleaner to remove dust from the ventilation holes on the back sides and bottom of the cabinet. Plastic surfaces are easily scratched and can be marred by alcohol and various solvents. Avoid excessive use of oil-based furniture polishes since the materials used in the cabinet will accumulate more dust. We recommend using a non-abrasive, antistatic cleaner and polisher.

Features for a Quality Picture (VCR)

Digital Auto Picture

Automatically controls the video output signal for less noise depending on the tape condition.

Digital Auto Tracking

Continuously analyzes the signal and adjusts for optimum picture quality.

Manual Tracking Control (to reduce picture noise)

Use during Playback and Slow Motion mode to reduce picture noise. Press CH (TRACKING) / on the remote control or on DECK until the picture clears up. To return to Auto Tracking, press POWER off, then on again a few seconds later.

V-Lock Control (to reduce picture jitter) In Still mode, CH (TRACKING) / operate as a V-Lock control.

D4743-4743S P1-25 (030318 C-lot).p65 2003/03/18, 15:286

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : consumerproducts@panasonic.com

Specifications

Power Source: 120 V AC, 60 Hz Power Consumption: Power On: Approx. 32 watts, Power Off: Approx. 4 watts

Video Signal: EIA Standard NTSC color Video Recording System: 4 rotary heads helical scanning system

Audio Track: 1 track (Normal), 2 channel (Hi-Fi Audio Sound) Tuner: Broadcast Channels: VHF 2 ~ 13, UHF 14 ~ 69 CABLE Channels: Midband A through I (14 ~ 22), Superband J through W (23 ~ 36)

Input/Output Terminal: Audio/Video Line Input/Output, RF Input/Output Input Terminal: Audio/Video Line Input (Front) Output Terminal: S-Video Output (DVD only), Component Video Output (DVD only)

Operating Temperature: 5 °C ~ 40 °C (41 °F ~ 104 °F) Operating Humidity: 10 % ~ 75 % Weight: 4.9 kg (10.8 lbs). Dimensions: 430 (W) x 95.5 (H) x 344 (D) mm

Discs Played (1) DVD-Video Disc 5” (12 cm) single-sided single-layer

(2) Compact Disc 5” (12 cm) disc

(CD-DA, Video CD) 3” (8 cm) disc (CD-R/CD-RW, MP3, WMA, JPEG)

Digital Audio Output: Digital Optical Connector Pickup: Wavelength: 655 nm (DVD), 790 nm (Video CD/CD)

Note: • Designs and specifications are subject to change without notice.

Hyperband AA ~ EEE (37 ~ 64), Lowband A-5 ~ A-1 (95 ~ 99) Special CABLE channel 5A (01), Ultraband 65 ~ 94, 100 ~ 125

Audio Output 2 (L), (R)

16-15/16” (W) x 3-12/16” (H) x 13-9/16” (D) inch

5” (12 cm) single-sided double-layer 5” (12 cm) double-sided double-layer (one layer per side) 3” (8 cm) single-sided single-layer 3” (8 cm) single-sided double-layer 3” (8 cm) double-sided double-layer (one layer per side)

Laser power: CLASS II

Definition of Terms (DVD)

Angle: Some DVD discs feature scenes simultaneously shot from different angles.

Chapter Number:Titles are subdivided into numbered sections. You can quickly search for

DVD: A high-density optical disc on which high-quality pictures and sound have

Playback Control:With Video CD (version 2.0), scenes or information may be selected for

Subtitles: Written dialogue which appears at the bottom of the screen. Time Number: The elapsed play time from the start of a disc or title. Use to quickly find

Title Number: For DVD discs with two or more titles, the title is numbered as title 1, title 2, etc. Track Number: Numbers assigned to tracks on Video CDs and CDs to allow specific tracks

Video CD: CD containing picture and sound with same quality level as video tape.

Apparatus Claims of U.S. Patent Nos. 4,631,603, 4,577,216, 4,819,098 and 4,907,093, licensed for limited viewing uses only.

This product incorporates copyright protection technology that is protected by method claims of certain U.S. Patents and other intellectual property rights owned by Macrovision Corporation and other rights owners. Use of this copyright protection technology must be authorized by Macrovision Corporation, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision Corporation. Reverse engineering or disassembly is prohibited.

The ANGLE button can be used to view the scene from different angles. (ANGLE Indicator lights on DECK when a scene recorded at different angles is detected.)

a favorite scene using these numbers.

been digitally recorded. DVD incorporates new video compression technology (MPEG II) and high-density recording technology which allow entire movies to be recorded with incredible playback quality.

viewing or listening from an interactive menu that appears on the TV screen.

scenes. (May not work with some discs.)

to be quickly located.

This DECK also supports Video CDs with playback control (version 2.0).

(Connection)

Initial Setup

D4743-4743S P1-25 (030318 C-lot).p65 2003/03/18, 15:287

Location of Controls

Remote Control

EJECT /

OPEN / CLOSE

pp. 20,

POWER

NUMBER keys

ACTION

pp. 18

, 47

SET

VCR mode

p. 28

STOP

pp. 20,

FAST FORWARD /

SEARCH / SLOW+

pp. 20,

REWIND /

SLOW-

pp. 20,

PAUSE /

pp. 20,

COMMERCIAL SKIP ZERO

pp. 31, 32

STILL

Bold: VCR Function

Italic

DVD Function

Bold Italic:VCR and DVD Functions

Normal: Others

INPUT

p. 35

TV mode

p. 28

CHANNEL

TRACKING

VOLUME

ADD/DELETE /

pp. 19,

V-LOCK

pp. 6, 21

p. 28

CLEAR

39, 46

p. 38

SELECT

DVD mode

p. 28

PLAY

pp. 20,

SKIP SKIP

p. 23

TITLE

p. 38

ZOOM

p. 37

ANGLE

p. 37

AUDIO

(SAP / Hi-Fi)

pp. 27,

COUNTER RESET

p. 32

VCR/TV

p. 21

RECORD

p. 21

PROGRAM

p. 24

EJECT button: When this button is pressed in VCR mode, the tape is ejected.

D4743-4743S P1-25 (030318 C-lot).p65 2003/03/18, 15:288

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : consumerproducts@panasonic.com

This button is inoperative if pressed during recording. If pressed in DVD mode, the disc tray opens or closes.

SUB TITLE

p. 36

Virtual Surround Sound

(V.S.S)

TAPE POSITION

VOLUME ADJUST

RETURN /

/ ENTER

pp. 23,

p. 34,

pp. 22,

DISPLAY

p. 11,

SPEED

p. 21

Front View of DECK

Bold: VCR Function

Italic

DVD Function

Bold Italic

Normal: Others

STOP/EJECT

p. 20

FAST FORWARD/SEARCH

p. 20

PLAY

p. 20

REWIND/SEARCH

p. 20

POWER

Audio/Video Input Connector 2 (LINE 2)

CHANNEL / TRACKING/V-LOCK

pp. 6, 21

REC

p. 21

VCR and DVD Functions

p. 35

Reset All Memory Functions

If the disc cannot be removed...

First, unplug DECK. Then, prepare a rigid wire (e.g. an extended paper clip) and, applying moderate force, insert it straight into the hole at the base of the tray. The tray will eject a little. Now, pull the tray all the way out and remove the disc.

Cassette Compartment

Multi Function

Display

p. 11

Remote Sensor

Over 2 inches

Disc Tray

Over 2 inches

OPEN/CLOSE

PROGRESSIVE

PAUSE

SKIP SKIP

p. 22

p. 10

p. 23

PLAY

p. 22

STOP

p. 22

(Connection)

Initial Setup

Use when moving DECK to new location, or if a mistake was made in the Initial Setup section (return to Factory Setting).

• Make sure a tape is not inserted in the DECK.

Turn DECK Power on.

Press and hold both VCR PLAY

D4743-4743S P1-25 (030318 C-lot).p65 2003/03/18, 15:289

and CHANNEL more than 5 seconds.

• The power shuts off. Do “Initial Setup (Ready to Play)”

on page 16.

on the DECK for

Location of Controls (continued)

Rear View of DECK

AC Power Plug

• While plugged into an AC outlet, this DECK consumes 4 W of electrical power in off mode.

Component Video Output Connector (Y, P p. 13

Optical Digital Audio Output Connector (DVD Only) p. 15

, PR) (DVD Only)

Bold: VCR Function

Bold Italic:VCR and DVD Functions

VHF/UHF Antenna Output Terminal p.12

VHF/UHF Antenna Input Terminal p. 12

Video Output Connector p. 12

••

S-Video Out Connector (DVD Only) pp. 10, 13

Audio Output 2 Connector (L/R) p. 13

Audio Output 1

Italic:DVD Function

Video Input Connector p. 35

Audio Input Connector (L/R) p. 35

Connector (L/R) p. 12

The following table shows the status of the output jacks when in VCR or DVD mode.

VCR

DVD

Video Output Audio Out 1 Audio Out 2

YES YES

Component Video Output

N/A

S-VIDEO OUT

N/A

YES

• PROG functions on the remote are not available when using Component Video Output

Note

and S-VIDEO OUT. Please set TV to either RF INPUT or VIDEO INPUT, and then press PROG.

To enjoy PROGRESSIVE SCAN video

(1). Connect

(See p. 13.)

(2). When the PROGRESSIVE button is pressed, the ON lamp lights up (see p. 9) and the

PROGRESSIVE SCAN signal is output from the

Notes

• The PROGRESSIVE button can be operated when the DECK is in DVD function mode.

• The screen may shift off-center when using progressive output. Please adjust the screen

position if this occurs. (Refer to your TV manual.)

• The DECK outputs video signals (not PROGRESSIVE SCAN) from the “VIDEO OUT” and “SVIDEO OUT” terminals when the ON lamp is lit.

D4743-4743S P1-25 (030318 C-lot).p65 2003/03/18, 15:2810

Component Video Output

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : consumerproducts@panasonic.com

to the component video input terminals of a television.

Component Video Output Connector

Displays (On Screen & Multi Function)

On Screen Displays (VCR)

Function & Channel Displays

CH 0 8

When a function button is pressed, e.g. PLAY, or you change channels, a 5-second display appears.

VCR Status & Clock Displays To display or remove overlay at right,

➛➛

➛ press DISPLAY.

➛➛

Rec Time Remaining (OTR mode only, see p. 21.)

Multi Function Display

VCR mode Indicator

Lights up when DECK is VCR mode.

Function Status

Broadcast Audio Being Received (See p. 26.)

Blank Tape/ No Video Signal Indications

Whenever a blank section of a tape comes up in Play mode, or when the selected channel has no broadcast signal with Weak Signal Display Feature (p. 33) set to OFF, the TV screen will turn solid blue.

Current Time

REC

1 2 : 0 0A

0 : 25

STER

EO SAP M

ONO

-0 : 1 2 : 3 4

CH 02

Channel

Counter

Tape Speed (See p. 6.)

DVD mode Indicator

Lights up when DECK is DVD mode.

(Connection)

Initial Setup

Tape Indicator

Lights up when a tape is inserted.

Hi-Fi Indicator

Lights up when Hi-Fi audio is monitored in Play mode.

VCR

Hi - Fi

ANGLE

ANGLE Indicator

Lights up when a scene recorded at different angles is detected. (See p. 37.) (DVD only).

Clock/ Status/ Channel/ Speed Display

Displays the current time. Briefly displays DECK status when a function button is pressed. Briefly displays the channel number, or “L1” or “L2” when a channel or line input is selected. Briefly displays the recording speed when SPEED is pressed.

D4743-4743S P1-25 (030318 C-lot).p65 2003/03/18, 15:2811

DVD

REC

A M

TIMER

AM/PM Indicator

DISC Indicator

Lights up when a disc is inserted.

VCR REC Indicator

Lights up during recording.

Timer Indicator

Lights up when DECK is set for Timer Recording, or when One Touch Recording (OTR) is used. Flashes when Timer Recording is set, but a tape has not been inserted into DECK and when a power interruption occurs during Timer Programming.

Connections

Basic Connections

• If your TV has AUDIO and VIDEO IN terminals, connect them to DECK for higher

quality picture and sound.

• You can enjoy stereo sound even if your TV is not stereo by connecting a stereo

amplifier to DECK.

• Connect DECK and TV with an RF Coaxial Cable a (supplied) or an AV Cable (not supplied) as shown in the figure below.

■ ■

■ DSS Receiver DECK TV

■ ■

■ DECK TV

■ ■

Antenna or Cable

■ Cable Box DECK TV

■ ■

DSS Receiver

OUT

DVD/VCR DECK

IN FROM ANT.

IN 1

OUT

VIDEO

AUDIO

WARNING

When using “Nut type” RF coaxial cables, tighten with fingers only. Overtightening may damage terminals.

VHF/UHF

OUT TO TV

OUT

Cable Box

1 Disconnect antenna or cable from TV

and connect to DECK.

2 Connect DECK to TV with RF Coaxial Cable.

RF COAXIAL CABLE

AUDIO IN

(supplied)

VIDEO

AV CABLE

VHF/ UHF

(not supplied)

Note to CABLE system installer

This reminder is provided to call the CABLE system installer’s attention to Article 820-40 of the NEC in USA (and to the Canadian Electrical Code in Canada) that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical.

D4743-4743S P1-25 (030318 C-lot).p65 2003/03/18, 15:2812

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : consumerproducts@panasonic.com

Other Connections

■ ■

■ With a Cable Box (DECK

■ ■

DVD/VCR DECK

IN FROM ANT.

IN 1

OUT

VHF/UHF

OUT TO TV

■■

■

Connect With Two Cable Boxes

■■

ANT or CATV

Cable Box

Cable Box TV)

OUTIN

DVD/VCR DECK

ANT

CATV

Cable Box

OUT

2-Way Splitter

OUT 1

OUT 2

OUT

Cable Box

OUTIN

IN 1

IN FROM ANT.

VHF/UHF OUT TO TV

A/B Switch

VHF/ UHF

IN 2IN 1

• view any (including

• use Remote

• record and view

AUDIO

VIDEO

scrambled) channel.

Control to select channels without using Multi-brand control feature.

both scrambled and unscrambled channels if additional equipment is added. This connection requires: two converter boxes, an A/B switch, and a 2-way splitter.

OUT

AUDIO

VIDEO

OUT

R L

VHF/ UHF

You CannotYou Can

• record scrambled channels.

You CannotYou Can

• view a channel other than the one selected for any type of recording.

• do a Timer recording of a channel unless you select it on the Cable Box.

Connections For DVD Only (enjoying higher picture quality)

Connect AUDIO OUT2 (L, R) to the AUDIO IN (L, R) of the TV. (audio input for COMPONENT

or S-VIDEO mode). If your TV has COMPONENT VIDEO INPUT, connect to COMPONENT VIDEO OUT.

If your TV does not have COMPONENT VIDEO INPUT but has S-VIDEO INPUT, connect to S-VIDEO OUT.

When in DVD mode, set your TV to either COMPONENT VIDEO IN or S-VIDEO IN.

Notes

• You can watch DVDs through the S-VIDEO or COMPONENT VIDEO, VHF/UHF OUT TO TV, and VIDEO OUT connections to your TV. The VCR and TUNER pictures are available only from the VIDEO OUT and VHF/UHF OUT TO TV connections to your TV.

• PROG functions on the remote are not available when using S-VIDEO OUT and COMPONENT Video Output. Please set TV to either RF INPUT or VIDEO INPUT, and then press PROG.

• TV must have capability to accept and display a progressive scan signal to use PROGRESSIVE mode. Consult your TV operating instructions.

DVD/VCR DECK

DVD OUTPUT

S-VIDEO OUT

COMPONENT

VIDEO OUT

P R

AUDIO OUT2

AUDIO

VIDEO

S-VIDEO IN

From DECK’s

A/V OUTPUT

(Connection)

Initial Setup

D4743-4743S P1-25 (030318 C-lot).p65 2003/03/18, 15:2813

Connections (continued)

Audio Connections

Ready Checklist

Turn down the volume, then turn DECK, as well as other equipment to be connected, off before proceeding with connection. Do not block ventilation holes of any of the equipment and arrange them so that air can circulate freely. Read through the instructions before connecting other equipment. Ensure that you observe the color coding when connecting audio and video cables.

■ Connecting Amplifier (2ch stereo system) [Analog connection]

DVD/VCR DECK

AUDIO OUT2

Speaker

Amplifier

AUDIO IN

R L

Enjoying digital audio output from the digital audio output connector

Notes on audio output from the optical digital audio output connector

Disc DVD

Sound recording format

Dolby Digital

Linear PCM (48/96 kHz 16/20/24bit)

DTS

Video CD CD MP3

WMA

*1 The type of audio output from the connector can be selected by the Settings for DVD

Operation. (See p. 48.)

*2 Sound having 96 kHz sampling is converted into 48 kHz sampling when it is output

from the DECK’s optical digital audio output connector.

MPEG 1 Linear PCM

MP3 WMA

For your reference:

• Dolby Digital is a digital sound compression technique developed by the Dolby Laboratories Licensing Corporation. Supporting 5.1-channel surround sound, as well as stereo (2-channel) sound, this technique enables a large quantity of sound data to be efficiently recorded on a disc.

• Linear PCM is a signal recording format used in CDs. While CDs are recorded in 44.1 kHz/16 bit, DVDs are recorded in 48 kHz/16 bit up to 96 kHz/24 bit.

• If you have a Dolby Pro Logic Surround decoder, you will obtain the full benefit of Pro Logic from the same DVD movies that provide full 5.1 channel Dolby Digital soundtracks, as well as from titles with the Dolby Surround mark. For information on Panasonic or Technics Dolby Pro Logic Surround Sound Decoders please contact your local dealer.

Optical digital audio output from connector

Dolby Digital bitstream (1 - 5.1 ch) or PCM (48 kHz sampling/16 bit only)*

Linear PCM (2 ch) (48 kHz sampling/16 bit only)*

Bitstream or PCM (48 kHz sampling/16 bit only)* PCM (44.1 kHz sampling)

Linear PCM (44.1 kHz sampling) Linear PCM (It depends on the MP3 file) Linear PCM (It depends on the WMA file)

Speaker

Manufactured under license from Digital Theater Systems, Inc. US Pat. No. 5,451,942, 5,956,674, 5,974,380, 5,978,762 and other world-wide patents issued and pending. “DTS” is a registered trademark of Digital Theater Systems, Inc. Copyright 1996, 2000 Digital Theater Systems, Inc. All rights reserved.

Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol are trademarks of Dolby Laboratories.

D4743-4743S P1-25 (030318 C-lot).p65 2003/03/18, 15:2814

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : consumerproducts@panasonic.com

■ Connecting Amplifier (5.1 ch Surround system) [Digital connection] DECK Dolby Digital Decoder Amplifier Speaker

DECK DTS (digital theater systems) Decoder Amplifier Speaker

When DVDs recorded in Dolby Digital or DTS are played, Dolby Digital bitstream or DTS bitstream is output from the DECK OPTICAL digital audio output connector. When DECK is connected to a Dolby Digital decoder or DTS decoder, you can enjoy theater-quality audio in your home. [An optical digital audio cable (optional) is required when an optional Dolby Digital decoder or DTS decoder is used.]

Notes on connecting an optical digital audio cable (optional)

• Firmly connect the cable to the connector.

(Connection)

Initial Setup

Surround Speaker

[5.1 ch Surround system]

Center Speaker

Surround Speaker

DVD/VCR DECK (Rear)

Optical Digital Audio Cable (optional)

Caution for optical digital audio output connector:

• When connecting an amplifier (with an Optical Digital Input Connector) which does not contain the Dolby Digital or DTS decoder, be sure to select “PCM” at “Dolby Digital” and “PCM” at “dts” of the Settings for DVD Operation “Audio Output” (see p. 48). Otherwise, any attempt to play DVDs may cause such a high level of noise that it may be harmful to your ears and damage your speakers.

• When a Dolby Digital/DTS decoder is connected, please select “Bitstream” at “dts” or “Dolby Digital” of the Settings for DVD Operation “Audio Output”. If “PCM” is selected, there will be stereo sound. (See p. 48.)

• Video CDs and CDs can be played as usual.

Note:

• Some DTS decoders which do not support DVD-DTS interface may not work properly with DECK.

Decoder with Dolby Digital /DTS processing (optional)

To Optical Digital Audio Input Connector

Front Speaker

Amplifier

Subwoofer

D4743-4743S P1-25 (030318 C-lot).p65 2003/03/18, 15:2815

Initial Setup for Basic Connections (Ready to Play)

Before doing Initial Setup

Turn TV on.

See connections a RF Coaxial Cable Connection and b AV Cable Connection on page 12.

<RF Coaxial Cable Connection> Set TV to channel 3.

Set TV to VIDEO.

[DECK

• Go to “Initial Setup (Ready to Play).” (See below.)

[Cable Box

• Turn on Cable Box and set it to your Public Broadcasting Station (PBS) channel

• If you use a DSS Receiver, it must be turned off.

Initial Setup (Ready to Play)

Press VCR on remote for VCR mode.

Plug DECK Power Cord into AC wall outlet. DECK comes on and auto channel and clock set starts.

• If screen below does not appear, check DECK - TV connection and, if TV is tuned to

• To change VCR’s output channel, please refer to “VCR’s Output Channel” on page 19.

➛➛

➛ TV]

➛➛

➛ DECK

➛➛

in your time zone.

channel 3, try switching it to channel 4.

➛➛

➛ TV], [DSS

➛➛

➛ DECK

➛➛

➛ TV]

➛➛

CH AUTO SET PROCEEDING

CANCEL : STOP

AUTO CLOCK SET

PROCEEDING

CANCEL : STOP

D4743-4743S P1-25 (030318 C-lot).p65 2003/03/18, 15:2816

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : consumerproducts@panasonic.com

Plugging the AC Power Plug into an AC outlet

Notes

• Function buttons are inoperative during Initial Setup.

• To remove a cassette during Auto Set, press EJECT on

the remote or STOP/EJECT twice on the DECK. In this case, settings must be made manually. (See p. 18.)

• Depending on conditions, Auto Clock Set may take longer than 30 minutes. If so, press STOP to stop setup and perform settings manually. (See p. 18.)

Continued on next page...

*Important: If a remote control button does not work when pressed,

press the VCR button on the remote and try the button again.

EJECT

ACTION

SELECT

SET

VCR

Settings are made automatically. When setup is done, this screen appears.

6 / 8/ 20 03

SUN 2 : 20P

SETT I NG

: CH

AUTO CLOCK SET

COMPLETED

DST :

If “AUTO CLOCK SET IS INCOMPLETE” appears, manually set clock. See below.

AUTO CLOCK SET IS I NCOM

PLETE

PLEASE SET CLOCK BY

ACT I ON KEY

PRESSING

Manual Clock Set

If Auto Clock Set was incomplete.

Press ACTION* on remote to display CLOCK screen.

(Connection)

Initial Setup

STOP

D4743-4743S P1-25 (030318 C-lot).p65 2003/03/18, 15:2817

SET CLOCK

1 / /

- - - - - - - - -- - - - - - - -- - - - - -

SELE CT MONTH

SELECT : SET :SET EXIT

: ACT I ON

Press set. In the same manner, select and set the

to select the month and SET to

DST : O

date, year, time, and DST (Daylight Saving Time).

SET CLOCK

6 / 8 / 2003 SUN 2: 2 0 PM

- - - - - - - - -- - - - - - - -- - - - - -

SET COMPLETE

SET : S START :

Press ACTION to start clock and exit.

DST :

ET BACK :

ACT I O

SELECT : EXIT

: ACTION

SET : SET

MENU SET UP VCR

SET CLOCK

SET UP CHANNEL IDIOMA/LANGUE : ENGLISH VCR’S OUTPUT CH:3

Reset Language, Channels, Clock, VCR’s

AUTO CLOCK SET

MANUNU

T I M

E ZONE AD

JUS

T :

SELECT :

SET :

SET

EXIT

: ACT I ON

SET CLOCK

DST :

6 / 8 / 2003 SUN 12: 0 0 PM

SELECT HOUROUR

- - - - - - - - -- - - - - - - -- - - - - -

SET CLOCK

SELE

CT :

SET

SET BACK :

EXIT

: ACT I ON

SET UP VCR

SET CLOCK SET UP CHANNEL IDIOMA/LANGUE : ENGLISH VCR’S OUTPUT CH:3

SELECT :

: ACTION

SET:SET

EXIT

Press ACTION*

to display MENU.

Language

1) Press to select

language item.

MENU SET UP VCR SET CLOCK SET UP CHANNEL

IDIOMA/LANGUE : ENGLISH

VCR’S OUTPUT CH:3

SELECT :

: ACTION

SET:SET

FIJAR : SET

➡

REGLER:SET

➡

SET:SET

EXIT

: ACTION

2) Press SET repeatedly to

change language item as shown below.

MENU PREPARAR VCR FIJAR RELOJ FIJAR CANAL

LANGUE/LANGUAGE:ESPAÑOL

CANAL DE SALIDA : 3

ELEGIR : SALIR

For Spanish

MENU REGLAGE MAGNETOSCOPE REGLAGE HORLOGE REGLAGE CANAL

LANGUAGE/IDIOMA:FRANÇAIS

CA SORTIE : 3

SEL. : QUITTER

For French

MENU SET UP VCR SET CLOCK SET UP CHANNEL

IDIOMA/LANGUE : ENGLISH

VCR’S OUTPUT CH:3

SELECT : EXIT

: ACTION

For English

3) Press ACTION to exit.

• PROGRAM functions are not available when using COMPONENT Video Output and S-VIDEO OUT. Please set TV to either RF INPUT or VIDEO INPUT, and then press PROGRAM.

Channels

1) Press to select

“SET UP CHANNEL,” and press SET.

MENU SET UP VCR SET CLOCK

SET UP CHANNEL

IDIOMA/LANGUE : ENGLISH VCR’S OUTPUT CH:3

SELECT :

CABLE

: ACT I ON

SET : SET

NNE

SPLAY : OFF

SET : SET

EXIT

: ACTION

2) Press to select

“ANTENNA,” then press SET to set your antenna system (“TV” or “CABLE.”)

SET UP CHA

ANT

ENNA

AUTO SET WEAK

S I GNAL D I

SELECT : EXIT

3) Press to select

“AUTO SET,” then press SET.

• If you use a Cable Box, set it to the PBS channel in your time zone.

CH AUTO SET PROCEEDING

CANCEL : STOP

• After Channel Auto Set is finished, Auto Clock Set will be performed.

Clock

1) Press to select

“SET CLOCK,” and

press SET.

2) Press to select “MANUAL,” and press SET. (For Auto Clock Set, select “AUTO CLOCK SET.”)

(“TIME ZONE ADJUST”

appears only when auto clock is set.)

3) Press and to

select, then set the date, time, and DST (Daylight Saving Time).

4) Press ACTION to start

Clock and exit this mode.

D4743-4743S P1-25 (030318 C-lot).p65 2003/03/18, 15:2818

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : consumerproducts@panasonic.com

HANNEL

08 ADDED

HANNEL

08 DELE T

*Important: If a remote control button does not work

when pressed, press the VCR button on the remote and try the button again.

POWER

CH /

NUMBER keys

Time Zone Adjust

(Only when Auto Clock is set.)

1) Press to select

“SET CLOCK,” and press SET.

MENU SET UP VCR

SET CLOCK

SET UP CHANNEL IDIOMA/LANGUE : ENGLISH VCR’S OUTPUT CH:3

SELECT : EXIT

: ACTION

2) Press to select

“TIME ZONE ADJUST,”

AUTO CLOCK SET MANU

T I M

SELECT : EXIT

: ACT I ON

and press SET to subtract or add hour(s) as necessary.

3) Press ACTION twice.

•“TIME ZONE ADJUST” returns to “0” if clock is set manually.

SET : SET

SET CLOCK

E ZONE AD

JUS

SET : SET

T :

VCR’s Output Channel

1) Press to select

“VCR’S OUTPUT CH.,” and press SET.

MENU SET UP VCR SET CLOCK SET UP CHANNEL IDIOMA/LANGUE : ENGLISH

VCR’S OUTPUT CH:3

SELECT : EXIT

: ACTION

2) Press SET.

I F YOU PRESS KEY, VCR’ SW I

TCHES TO

3) Press ACTION.

PLEASE TUNE YOUR TV TO CH 4.

➡

After 3 seconds

MENU SET UP VCR SET CLOCK SET UP CHANNEL IDIOMA/LANGUE : ENGLISH

VCR’S OUTPUT CH:4

SELECT : EXIT

: ACTION

• To Make Corrections, repeat steps 1) ~ 3).

SET : SET

ACT I O

S OUTPUT CH

CH 4.

SET : SET

ADD/DLT SELECT

SET

VCR

ACTION

Add or Delete a Channel

To add channel: Select channel with NUMBER keys

and press ADD/DLT.

To delete channel: Select channel with CH / or

NUMBER keys and press ADD/DLT.

DST (Daylight Saving Time)

DECK auto adjusts clock for DST. (p. 17.)

Spring (First Sunday in April)

DST:ON

Autumn (Last Sunday in October)

DST:ON

➛➛

➛ Sets clock ahead one hour.

➛➛

➛ Turns clock back one hour.

➛➛

Operation

Basic

• If your area does not observe Daylight Saving Time, select DST:OFF.

• Keep these time changes in mind when programming DECK for timer recordings.

D4743-4743S P1-25 (030318 C-lot).p65 2003/03/18, 15:2819

Playback/ Record on a Tape

Ready Checklist

All connections are made. (pp. 12 ~ 15) TV and DECK are plugged in. TV is on and tuned to CH 3, 4, or VIDEO. Remote is in VCR mode. (Press VCR.)

Playback a Tape

Insert a tape.

• DECK power comes on. If Auto VCR/TV (see p. 32) is set to “OFF,” press VCR/TV on the remote to be VCR mode.

Press PLAY* to play a tape.

• If tape has no rec. tab (p. 6), auto play begins.

Special Features During Play

Forward/Reverse Scene Search

➛➛

➛ Press FF/SLOW+ or REW/SLOW-.

➛➛ ➛➛

➛ Press PLAY to release.

➛➛

After search has begun, each additional press of FF or REW changes speed as shown below.

[SLP] : Approx. 21X [LP] : Approx. 9X [SP] : Approx. 7X

If at 21X, 9X, or 7X speed the picture is interrupted, change speed to 9X, 7X, or 3X.

Notes

• Picture interruption may occur with some TVs.

• FF and REW search speed may vary

depending on current tape position.

Still (Freeze) Picture

➛➛

➛ Press PAUSE/STILL.

➛➛ ➛➛

➛ Press PLAY to release.

➛➛

Frame by Frame Picture

➛➛

➛ Press PAUSE/STILL in Still mode.

➛➛ ➛➛

➛ Press PLAY to release.

➛➛

Slow Motion Picture

➛➛

➛ Press FF/SLOW+ (increase speed) or

➛➛

REW/SLOW- (decrease speed) in Still mode.

➛➛

➛ Press PLAY to release.

➛➛

↔ Approx. 9X ↔ Approx. 7X ↔ Approx. 3X

EJECT

CH /

VCR

STOP

REW/

SLOW-

PAUSE/

STILL

VCR/TV

REC

Notes

• These features work best in SP or SLP mode.

• The sound will be muted.

• To reduce picture noise, see “Manual Tracking Control” on page 6.

• After DECK is in Still or Slow mode for 3 minutes,

it will switch to Stop mode automatically to protect the tape and the video head.

DVD

PLAY

FF/ SLOW+

SPEED

Playback using DECK buttons

Press PLAY.

Insert a tape.

Press STOP to stop a tape.

Press REW/SLOW- or FF/SLOW+ in Stop mode to rewind or fast forward a tape.

Press EJECT on remote, or STOP/EJECT

on DECK to eject a tape.

D4743-4743S P1-25 (030318 C-lot).p65 2003/03/18, 15:2820

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : consumerproducts@panasonic.com

Multi Function Display

Press STOP/EJECT to stop and/ or eject a tape.

*Important: If a remote control button does not work when pressed,

press the VCR button on the remote and try the button again.

Record on a Tape

Insert a tape with a record tab (p. 6).

• DECK power comes on. If Auto VCR/TV (see p. 32)

is set to “OFF,” press VCR/TV on the remote to be VCR mode.

Press CH , or NUMBER keys

to select the channel.

• For “LINE” input, see page 35.

• If channel is over 100, press 100 key then press

the remaining 2 digits.

Press SPEED

to select the record speed (p. 6).

SP = Standard Play LP = Long Play SLP = Super Long Play

• Speed appears on-screen and on Multi Function Display.

Press REC

to start recording.

(The VCR REC indicator lights up on Multi Function Display),

• To edit out unwanted scenes, press PAUSE/STILL

to pause, and again to resume recording.

• You cannot view another channel during recording.

Press STOP

to stop recording.

One Touch Recording (recording in progress),

➛➛

➛ press REC repeatedly to set the recording length

➛➛ ➛➛

➛ (30 min. ~ 4 hours).

➛➛

• DECK shuts off after the preset record length.

Record one station, watch another,

➛➛

➛ press VCR/TV on the remote

➛➛

(change to TV mode),

➛➛

➛ select channels at TV (recording continues).

➛➛

Select Channels at DECK (In STOP or REC. PAUSE mode),

➛➛

➛ press VCR/TV on the remote

➛➛

(change to TV mode),

➛➛

➛ select channels at DECK.

➛➛

Play a disc while recording a tape.

➛➛

➛ insert a disc during recording,

➛➛ ➛➛

➛ press

➛➛

Notes

• It is not possible to record from DVD/ Video CD/ CD to VHS tape using DECK.

• Watching one channel and recording another is not possible when using Cable Box or DSS Receiver.

• After 5 minutes in Pause mode, DECK stops to protect a tape and video heads.

DVD

, and then press

PLAY

This video recorder, equipped with HQ (High Quality) system, is compatible with existing VHS equipment. Only use tapes with the mark. Only tapes tested and inspected for use in 2, 4, 6, and 8 hour machines are recommended.

Note

Remove loose or peeling labels from tapes to prevent tape jam.

Normal Rec

0:30 1:00

1:302:003:004:00

Record using DECK buttons

Insert a tape.

Select

Channel.

Multi Function Display

Press STOP/EJECT to stop.

Press REC to start recording.

Operation

Basic

D4743-4743S P1-25 (030318 C-lot).p65 2003/03/18, 15:2821

Basic DVD Operation

Ready Checklist

All connections are made. (pp. 12 ~ 15) DECK is plugged in. If DECK is connected to an audio amplifier,

turn the stereo system’s power on.

POWER

SELECT

SET

STOP

REW/

SLOW-

FF/

SLOW+ PAUSE/

STILL

OPEN/ CLOSE

NUMBER keys

DVD PLAY

SKIP SKIP

TITLE

VSS

RETURN

1 2

If an interactive DVD*1 or a Video CD with playback control*2 is used and TITLE MENU appears, go to step 5.

Press

POWER*

Press

DVD

• If a disc is already inserted, go to step 4. (Depending on the disc, playback may start automatically.)

Press

OPEN/CLOSE

and then place a disc into the disc tray.

Press

PLAY

Disc tray closes automatically.

READING

on the remote or DECK.

to select DVD mode.

• Hold disc by its edges only (p. 4) with printed side up and use guides to

place into tray.

Use 3” (8 cm)

or 5” (12 cm) disc.

to start playing.

• You may also close tray by

pressing

• Data reading time differs with each disc.

OPEN/CLOSE

T I TLE MENU

Dogs

Love

Cas t l es

i r

Operation using DECK buttons

Press

3, 7

Press POWER.

Insert a disc.

*1Interactive DVD...

May include multiple camera angles, stories, etc.

*2Video CD with playback control...

Particular scenes or information can be interactively selected from a menu that appears on the screen.

D4743-4743S P1-25 (030318 C-lot).p65 2003/03/18, 15:2822

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : consumerproducts@panasonic.com

OPEN/CLOSE.

Press PLAY.

Press STOP.

T I TLE MENU

Using NUMBER keys starts playing automatically.

The number of available titles varies with each disc.

<Input

Example>

Press menu screen.

• SKIP function not available with all discs. Please refer to disc jacket for operation information.

To return to menu (play stops)

Press Press

Press

Cas t l es

Dogs

i r

Love

SKIP

TITLE, MENU, RETURN

Dogs

of the world

1 digit number 1 ••• 1 2 digit number 12 ••• 10 1 2 3 digit number 123 •••100 1 2 3

| or | to go to next or previous

. (Video CD)

STOP

OPEN/CLOSE

Press or

NUMBER keys

below) to select title, and press

PLAY

to start playing.

•“Pressing is not necessary when using

NUMBER keys.

RETURN

to stop playing.

. (DVD)

to eject the disc.

SET

(see

PLAY

”

*Important: If a remote control button does not work when pressed,

VSS OFF (default)

VSS1

VSS3

VSS2

press the DVD button on the remote and try the button again.

■ Forward/Reverse Scene Search

Press

FF/SLOW+

REW/SLOW-

during play.

PLAY

Press

• Starting forward/reverse search during play started from menu on Video CDs may recall menu.

• Search speed, slow at first, increases with each additional press of the button up to 5 levels.

to release.

■ Forward/Reverse Chapter/Track Skip

Press

SKIP

| or |

SKIP

during play. Each press skips a chapter (DVD) or track (Video CD/CD).

• Pressing |

chapter/track returns to the start of that chapter/track. Each additional press skips back one chapter/track.

• Pressing

from menu on Video CDs may recall menu.

Chapter/Track Chapter/Track Chapter/TrackChapter/Track

Reverse Skip Forward Skip

SKIP

once midway through a

SKIP

| or | during play started

Current playback position

■ Still Picture or Pause

Press

PAUSE/STILL PLAY

Press

• DVD/Video CD : DECK will enter still picture mode.

• CD : DECK will enter pause mode.

to release.

during play.

■ Frame by Frame Picture

(DVD/Video CD) Press

PAUSE/STILL

PLAY

Press

• Each press advances picture one frame.

• Hold button down for consecutive frame advance.

• Whether pictures are advanced by “FRAME” or

“FIELD” is selected automatically. (See p. 49.)

to release.

in still mode.

■ Slow Motion Picture (DVD/Video CD)

Press

FF/SLOW+

REW/SLOW-

in still mode.

PLAY

Press

• Slow motion speed, slow at first, is increased

with each additional press of the button up to 5 levels.

• Reverse slow motion is not available for Video CDs.

to release.

Auto-Power Off Function

Power turns off after DECK has been in Stop mode (DVD) for about 5 minutes.

• When appears on the screen while a button

is being operated, it means that the corresponding operation is prohibited by DECK or the disc.

V.S.S. (Virtual Surround Sound)

Enjoy a surround-like effect if you are using two front speakers only. The effect is broadened and sound seems to come from virtual speakers on either side if the disc has surround signals recorded on it.

Press

VSS

• The Surround sound effects can be changed by pressing VSS repeatedly as shown by the figure below.

in DVD mode.

VSS OFF

Note

• Surround sound effects is available in DVD mode only.

• Turn off the surround effects on the other equipment.

• V.S.S. will not work, or will have less effect, with some discs.

• Turn V.S.S. off if it causes distortion.

• Sound will only come from the two front

speakers if V.S.S. is on.

Resume Function

DECK memorizes the point where STOP is pressed (STOP is displayed on screen).

Press

PLAY

Pressing

cancels RESUME, however, RESUME is not canceled when power is turned off and on.

• RESUME works only with discs for which elapsed play time is displayed during play.

Enjoy Video CDs featuring playback control without using menus (Video CDs only)

1. Do steps 1-4 (previous page).

When menu appears, press

2. Press

track (play begins).

• Check disc for track numbers.

• Press “1” to start at beginning of disc.

To Resume Menu use,

Press

menu will be displayed. Now, go to step 5 (previous page).

Notes

• Please read the disc jacket for operation information.

• If a single sided disc is placed in upside down, “THIS TYPE OF DISC CANNOT BE PLAYED. PLEASE INSERT A DIFFERENT DISC” is displayed.

• Remove disc and press DECK POWER off when not in use.

• Disc continues to rotate with menu displayed even after play is done. Press STOP to clear menu display when finished with menu.

to resume play from this point.

STOP

again or opening the tray

NUMBER keys

STOP

and press

to select desired

PLAY

STOP

, then the

Operation

Basic

D4743-4743S P1-25 (030318 C-lot).p65 2003/03/18, 15:2823

Timer Recording

Ready Checklist

All connections are made. (pp. 12 ~ 15) TV and DECK are plugged in. Clock set correctly. (p. 18) Tape has rec.tab. (p. 6) Remote is in VCR mode. (Press VCR.) Sufficient tape remaining for recording time.

Press PROG*

to display Program.

POWER

DATE START ST

SUN --:-- --:-- --

TODA

- - - - - - - - -- - - - - - - -- - - - - - -

SESELE CT START DAT

CT :

SELE SET

END

: PROG

Example

Today

SELECT /

Selection Order

WEEKLY

(SAT)

START

13 10 : 00 P 12 : 00 P 02

-- -- : --

-- : -- -- : -- --

CANCEL : ADD / DLT SELECT 1-8 : E

NTER

EXIT

: PROG

OPC

SET

WEEKLY

STOP CH

-- : -- --

: SET

1) To set record DATE,

SLP

press

1~31= one time, or DAILY= MON~ FRI, or WEEKLY= same time each week and press SET.

• See selection order left.

2) To set remaining items,

DAILY

(SUN)

WEEKLY

(MON)

press

to select and

press SET

to set START/ STOP times, CH (channel) or LINE input (p. 35), and tape speed (SP, LP, SLP).

Press PROG

to end programming.

To Enter More Programs,

SPD

press

to select and

press SET

to set an unused program number, and then repeat step 2.

Press PROG

to exit.

to select:

VCR mode Indicator

Multi Function Display

VCR

Hi - Fi

ADD/DLT SELECT

SET VCR

PROG

VCR REC Indicator

REC

A M

TIMER

TIMER Indicator

• The “Timer” Indicator lights up on DECK.

• You can do Timer Recording with the power on or off.

•“TIMER REC WILL START SOON” appears on-screen for 2 minutes

D4743-4743S P1-25 (030318 C-lot).p65 2003/03/18, 15:2824

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : consumerproducts@panasonic.com

before Timer Recording starts. If DECK is in DVD mode, no message appears, but the VCR REC Indicator, the VCR mode indicator and “REC” will flash on Multi function Display.

*Important: If a remote control button does not work when pressed,

press the VCR button on the remote and try the button again.

Review, Replace or Clear Program Contents:

(Recording is not in progress)

Press PROG

to display Program List.

START

STOP CH

7 9 : 00A 12 : 00A 08

10 : 00P

12 : 00P 02 SP

8 : 00P

9 : 00P 10

9 : 00P 10 : 00P

CANC

EL : ADD /

SELECT

1-8 : ENTER : SET EXIT

: PROG

DLT

To Replace program...

DATE

TART

7 SUN 9:00A 12:

TODA

----------------------------------------

SELE CT

SELECT : SET

END

To Clear program...

START

-- -- : --

10 : 00P

8 : 00P

SU 9 : 00P 10 : 00P

CANC

EL : ADD / SELECT ENTER : SET EXIT

Press PROG

to end the programming.

TOP

START DAT

SET

: PROG

STOP CH

-- : -- -- 12 : 00P 02 SP

9 : 00P 10

DLT

1-8 :

: PROG

00A 08

SPD

BACK :

SPD

SP LP

Press

to select number and

press SET

to display.

Repeat Step 2 (p. 24) to set new programs.

Press ADD/DLT.

To cancel a Timer Recording in progress...

Hold down STOP in VCR mode for

a few seconds to cancel the Timer Recording.

(The “TIMER” Indicator goes out on Multi Function Display.)

• Any future daily or weekly recording will be performed as programmed.

Operation

VCR

Notes

• If you are using a Cable Box, the VCR’s channel for Timer Recording must be set to the Cable Box input channel and Cable Box must be manually set to the desired channel. Cable Box power must be left on.

• 2 minutes before Timer Recording is performed, “PLEASE PREPARE FOR TIMER REC” appears and Timer Indicator flashes. Be sure a cassette with record tab is loaded and DECK is in Stop mode.

• If a power interruption occurs while programming the timer, the timer program(s) may be canceled. If “TIMER PROGRAMS WERE LOST DUE TO POWER INTERRUPTION” appears on-screen, please re-enter the timer programs.

• If the start time for Timer Recording comes up during recording and playing back, Timer Recording will not be performed.

• When recording programs via DSS Receiver, DSS Receiver must be left on.

• When recording programs via an antenna or cable, DSS Receiver must be turned off.

D4743-4743S P1-25 (030318 C-lot).p65 2003/03/18, 15:2825

Important notes when using DSS Receiver

MTS Broadcast/ VHS Hi-Fi Stereo System

Connection

Make the Audio/Video Connection as shown on pp. 12 ~ 15.

• You can use TV connected to a Stereo amplifier and speakers instead of Stereo TV.

Receivable Broadcast Types

The following are possible audio broadcast types and onscreen displays.

The signal being received is indicated with an “ while the selected audio mode is indicated with an arrow.

To display the broadcast signal being received,

➛➛

➛ press DISPLAY*.

➛➛

” mark

MTS Stereo and SAP broadcast

Multi-channel Television Sound Stereo (main language) and Secondary Audio Program (sub language) broadcasts are being received simultaneously. Select STEREO or SAP audio mode.

MTS Stereo broadcast

Multi-channel Television Sound Stereo broadcast. Select STEREO audio mode.

• If stereo broadcast is weak and display flickers, select MONO audio mode for possible better results.

SAP broadcast

Secondary Audio Program (sub language) broadcast. Select SAP audio mode for the sub language.

MONO broadcast

Normal monaural sound broadcast.

STOP 1 2 : 0 0A

STER

EO SAP M

ONO

STOP 1 2 : 0 0A

STER

EO SAP M

ONO

STOP 1 2 : 0 0A

STER

EO SAP M

ONO

STOP 1 2 : 0 0A

STER

EO SAP M

ONO

0 : 0 0 : 0 0

CH 02

AUDIO

(SAP/Hi-Fi)

DISPLAY

Equipped with ®-TV Noise Reduction for true MTS reproduction.

-TV Noise Reduction is required for good stereo

separation and audio fidelity.

is a registered trademark, and is licensed by

Technology Licensing.

D4743-4743S P26-35 (030318 C-lot).p65 2003/03/18, 15:2826

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : consumerproducts@panasonic.com

*Important: If a remote control button does not work when pressed,

press the VCR button on the remote and try the button again.

Audio Mode for Recording

Press AUDIO (SAP/Hi-Fi)

to display audio mode.

(Display disappears after 5 seconds.)

Press AUDIO (SAP/Hi-Fi) repeatedly

STER

EO SAP M

ONO

Make a recording.

See p. 21.

to select desired mode.

• Refer to “Receivable Broadcast Types” on p. 26.

• Arrow indicates selection.

Operation

Audio Mode for Playback

Start playback.

See p. 20.

Press AUDIO (SAP/Hi-Fi)

to display audio mode.

H I F I

: L / R

H I F I

: L

H I F I

ORM

• Arrow indicates selection.

Notes

• Only tapes recorded in Hi-Fi stereo will playback with true stereo sound. Standard stereo tapes will playback in monaural sound.

• To listen to Hi-Fi stereo playback, the DECK AUDIO (L/R) jacks must be connected to a stereo TV or an external stereo amplifier and speakers. (See pp. 12, 14.)

• If tracking is adjusted during playback, Hi-Fi audio may revert to normal audio.

• Hi-Fi and normal audio playback volume level may differ.

Press AUDIO (SAP/Hi-Fi) repeatedly to select desired mode.

• Select “HIFI (L/R)” or “HIFI (L)” or “HIFI (R)” to listen to stereo recordings in stereo sound. Select “NORMAL” for monaural sound.

• Display disappears after 5 seconds.

VCR

D4743-4743S P26-35 (030318 C-lot).p65 2003/03/18, 15:2827

Multi-Brand Control Feature

Multi-Brand Control Setup

The Remote Control can be set to control some TV functions.

Find your TV Brand Code Number on the

following page.

POWER

Set up for TV control,

➛➛

➛ hold down TV button,

➛➛ ➛➛

➛ enter code with NUMBER keys.

➛➛

• If code number is 100 or greater,

➛ e.g., press 1 - 0 - 2 for 102.

Confirm code entry,

➛ press POWER to turn selected unit on or off.

• See table below for controllable functions in each mode.

Notes

• Repeat setup after remote battery replacement.

• Remote will not control every TV made by the

manufacturer listed. If you get no response, your particular unit cannot be controlled. There are NO additional codes for the products listed. If your product is not listed, then the remote is not compatible with that product.

Using Multi-Brand Control

After remote is set up, you can select VCR, DVD, or TV for the desired function.

Press VCR,

(Table below shows available remote buttons for each mode.)

Mode

DVD/VCR

DVD

, or TV on the remote.

Unit

EJECT/

DISPLAY, PLAY, STOP FF/SLOW+, REW/SLOW-

VCR/TV, PAUSE

AUDIO

TAPE POSITION, COUNTER RESET, SPEED, REC

DVD/VCR

OPEN/CLOSE

, CM/ZERO,

All

/STILL, SKIP

VOL +/

POWER, INPUT, NUMBER keys, ENTER, CH / , VOL +/

NUMBER keys

DVD

VCR

ENTER

* Bold: VCR Function

Italic: DVD Function

Notes

• Not all functions listed may be controllable.

• In TV mode, it may be necessary to press ENTER after pressing NUMBER keys

for channel selection.

D4743-4743S P26-35 (030318 C-lot).p65 2003/03/18, 15:2828

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : consumerproducts@panasonic.com

Bold Italic: VCR and DVD Functions

Normal: TV

TV Brand Code Numbers

Panasonic ....................... 01, 02

Quasar ............................ 01, 02

RCA ....................................... 03

GE ......................................... 03

Zenith .................................... 04

Magnavox .............................. 05

Sylvania ................................ 05

Sharp ............................... 06, 07

Sony ...................................... 08

Toshiba ................................. 09

Sanyo .................................... 10

Fisher .................................... 10

JVC........................................ 11

Hitachi ................................... 12

Mitsubishi ........................ 07, 13

Samsung ............................... 14

Gold Star ................... 15, 16, 17

Important Notes

• Some manufacturers use several codes for one brand. If the first code entered fails, try the next one listed.

• Some TV brands require you to turn on the power manually.

Operation

VCR

D4743-4743S P26-35 (030318 C-lot).p65 2003/03/18, 15:2829

Tape Operation

Search System

For each recording, an invisible index mark is placed on the tape. A program index and information are also included for timer recordings. These marks are used to access or scan recordings.

Index Search

Program End Search

INDEX SEARCH

ENTER INDEX NUMBER :1 USING 1- 9 KEYS

FORWARD SEARCH :FF REVERSE SEARCH :REW NEXT :SEARCH EXIT :STOP

Press SEARCH*

to display SEARCH in Stop or Play mode, and then

press NUMBER keys

to select recording number.

• To calculate number, see below.

Press FF/SLOW+

or REW/SLOW- on the remote to start search.

INDEX SEARCH

Play begins at search end. To search forward

FORWARD SEARCH : FF REVERSE

SEARCH : REW

or back 1 index,

press FF/SLOW+ or REW/SLOW- on the

remote while screen left is displayed (10 sec.).

• To cancel, press PLAY or STOP.

To Calculate Index Number

Example 1:

To go to rec. 2 from rec. 4, enter 3 and press REW.

61572 34

Locates end point of recording for continuity.

Press SEARCH twice to display SEARCH in Stop or Play

mode.

PROGRAM END SEARCH

Press FF/SLOW+

on the remote to start PROGRAM

SEARCH START : FF

EXIT

:SEARCH

END SEARCH.

• To cancel, press PLAY or STOP.

Examples of Program End Search.

Fig. 1

Program 1

the current tape position Press SEARCH button

INDEX

Program 2 or BLANK

End Point

Fig. 2

INDEX

Program 1

Fig. 3

INDEX

Program 1

End Point

the current tape position Press SEARCH button

BLANK

INDEX

Program 2

If search exceeds

a few seconds in BLANK area.

BLANK

End Point

Program 2

Example 2:

To go to rec. 6 from rec. 2, enter 4 and press FF.

17534 62

NOTE: indicates start points of each recording.

Note

• If Index Search is started very close to an index mark, that index mark may not be counted in the search.

D4743-4743S P26-35 (030318 C-lot).p65 2003/03/18, 15:2830

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : consumerproducts@panasonic.com

Upon locating end point,

➛➛

➛ search continues 7 sec. past end point,

➛➛ ➛➛

➛ tape rewinds to 10 sec. before end point,

➛➛ ➛➛

➛ tape plays to end point and stops.

➛➛

Note

• If Program End Search is started very close to an index mark, that mark may be skipped over.

PLAY

1st Press

2nd Press

3rd Press

1 min Skip

2 min Skip

3 min Skip

*Important: If a remote control button does not work when pressed,

press the VCR button on the remote and try the button again.

Auto Operation Functions

Auto Play

Insert a tape ➛ Power comes on, ➛ Play starts if there is no record tab

(see p. 6).

Auto Rewind

NUMBER keys

Play Fast Forward

Play Auto Eject

(Repeat Play must be off)

➛ ➛

➛ Tape end

Play

➛ ➛

➛ Tape ejects if set some programs.

➛ ➛

➛ Tape end ➛ Rewind

➛ ➛

➛ Rewind

➛ ➛

Operation

STOP

PLAY

REW/SLOWFF/SLOW+ CM/ZERO

VCR

Commercial Skip

VCR fast forwards (skips) over 1~3 minutes of recorded tape.

Press CM/ZERO in Play mode.

• The skip time can be changed by pressing CM/ZERO repeatedly as shown by the figure below.

• No indication appears on-screen.

D4743-4743S P26-35 (030318 C-lot).p65 2003/03/18, 15:2831

Tape Operation (continued)

REPEAT

REPEAT PLAY : O

REMOTE W

ARN I NG

: O

AUTO

SHU

T-OFF

: O

AUTO

VCR/TV

: OFF

SELE

CT :

SET: SET

END

: ACT I ON

SET

UP VCR

SELECT : EXIT

: ACTION

SET : SET

SET UP VCR

SET CLOCK SET UP CHANNEL IDIOMA/LANGUE : ENGLISH VCR’S OUTPUT CH:3

Repeat Play

Set to playback a recording over and over.

Press ACTION*

to display MENU.

1 2

SELECT : EXIT

REPEAT

REMOTE W AUTO AUTO

SELE END

SET UP VCR

SET CLOCK SET UP CHANNEL IDIOMA/LANGUE : ENGLISH VCR’S OUTPUT CH:3

SET : SET

: ACTION

SET

UP VCR

PLAY : O

ARN I NG

: O

SHU

T-OFF

: O

VCR/TV

CT :

: ACT I ON

Press

to select “SET UP VCR,” and

press SET.

Press

to select “REPEAT PLAY,”

: OFF

and press SET to set “ON” or “OFF.”

SET: SET

• Play repeats at tape end or if unrecorded portion over 30 sec. is detected.

Press ACTION twice to return to normal screen.

Note

• For repeat play in DVD mode, see page 42.

Zero Search

To quickly return to a specified tape location.

Press DISPLAY during play

to display Counter.

PLAY

1 2 : 0 0A

0 : 0 0 : 0 0

Press COUNTER RESET

at desired position to reset to “0:00:00”.

VCR/TV Selector Feature

The VCR/TV selection can be set to auto or manual.

Press ACTION

to display MENU.

1 2

• OFF(Manual):You select “VCR” or

• ON(Auto): “VCR” mode is

Press ACTION

to return to normal screen.

Note

• For more on VCR/TV selection, see “Record one station, watch another”

and “Select channels at DECK” sections (see p. 21).

“TV” mode using the VCR/TV button on the remote.

automatically set when VCR is turned on, or in Play mode.

Press

to select “SET UP VCR,” and

press SET.

Press

to select

“AUTO VCR/

TV,” and

press SET

to set “ON” or “OFF.”

Continue to record, playback etc.

Press STOP.

REW

1 2 : 3 0A

STOP

1 2 : 3 1AM CH 02

M CH 02

0 : 0 0 : 0 0

Press CM/ZERO in

0 : 30 : 30

to start Zero Search.

Stop mode

• DECK will go into FF or REW mode and stop at the last point the Counter was set to 0:00:00.

D4743-4743S P26-35 (030318 C-lot).p65 2003/03/18, 15:2832

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : consumerproducts@panasonic.com

Special VCR Features

Weak Signal Display Feature

When “ON,” picture is displayed regardless of signal strength.

Press ACTION

to display MENU.

ACTION

SELECT

SET STOP

CM/ZERO COUNTER

RESET

DISPLAY

VCR Lock Feature

When set to ON, all operations except for timer record and tape eject are prohibited. Useful for households with small children.

To turn on, hold down REC on DECK in Stop mode with no tape inserted for 7 seconds.

(Please ignore “NO CASSETTE” warning.)

VCR LOCK ACT I VA

To turn off, repeat above.

VCR LOCK OFF

• VCR Lock cancels in 24 hours if clock is set.

TED

MENU SET UP VCR SET CLOCK

SET UP CHANNEL

IDIOMA/LANGUE : ENGLISH VCR’S OUTPUT CH:3

SELECT : EXIT

: ACTION

SET UP CHA

ANT

ENNA

: CABLE

UTO SE

WEAK

S I GNAL D I

SELECT : EXIT

: ACT I ON

• ON: Picture is displayed regardless of signal condition, and may not always be clearly visible.

OFF: Screen turns solid blue when signal is weak or

non-existent.

• Selecting ON has no effect on connected equipment

with blue back feature.

Press ACTION twice to return to normal screen.

Auto Shut-Off Feature

The power shuts off at a preset time.

Press ACTION

to display MENU.

SET UP VCR

SET CLOCK

SET UP CHANNEL IDIOMA/LANGUE : ENGLISH VCR’S OUTPUT CH:3

SELECT : EXIT

: ACTION

SET

UP V REPEAT PLAY : O REMOTE W

AUTO

SHUT-

AUTO

VCR/TV

CT :

SELE EXIT

: ACT I ON

ARN I NG

*Important: If a remote control button does not work

when pressed, press the VCR button on the remote and try the button again.

Press

to select “SET UP CHANNEL,” and

SET : SET

NNE

SPLAY:OFF

press SET.

Press

to select “WEAK SIGNAL DISPLAY,” and

press SET

SET: SET

to set “ON” or “OFF.”

Press

to select “SET UP VCR,” and

press SET.

SET : SET

Press

FF N

to select “AUTO SHUT-OFF.”

Press SET repeatedly to change shutoff time as

SET: SET

shown below.

OFF

2 Hours

4 Hours

6 Hours

OFF

: O

Operation

VCR

REC

D4743-4743S P26-35 (030318 C-lot).p65 2003/03/18, 15:2833

Press ACTION twice

to return to normal screen.

Note

• The shut-off countdown will not function during Play or Record.

Special VCR Features (continued)

Remote Warning Feature

*Important: If a remote control button does not work

If Multi-brand feature is used (p. 28), and this feature is set to on, a warning appears whenever an invalid key is pressed in TV mode.

Press ACTION*

to display MENU.

SET UP VCR

SET CLOCK

SET UP CHANNEL IDIOMA/LANGUE : ENGLISH VCR’S OUTPUT CH:3

SELECT : EXIT

: ACTION

REPEAT PLAY : O

REMOTE W

AUTO

SHUT-

AUTO

VCR/TV

CT :

SELE EXIT

: ACT I ON

SET

ARN I NG

UP V

OFF

: O

SET : SET

: O

: OFF

SET: SET

Press

to select “SET UP VCR,” and

press SET.

Press

to select

“REMOTE WARNING,” and

press SET to set “ON” or “OFF.”

• If “OFF,” remote warning will not appear when invalid key is pressed.

Press ACTION twice to return to normal screen.

Tape Position and Tape Status Feature

To find out the present tape position and amount of tape remaining.

Tape position is displayed for VHS-C type Cassettes, tapes under 30 minute long, and some other tapes, but the position is not correct.

Press TAPE POS.

to detect current tape position.

DETECTING TAPE POSITION

R 120 M

BEG I

N END

•“DETECTING TAPE POSITION” is displayed only when a cassette is first inserted, and it takes several seconds for correct tape position to appear.

• The present tape position indication and amount of tape remaining (according to tape speed) is displayed.

• Tape remaining time display may not be precise.

when pressed, press the VCR button on the remote and try the button again.

INPUT

ACTION

SELECT

SET STOP

PAUSE/ STILL

Tape Position REC

Press TAPE POS.

to return to normal screen.

Note

This function cannot display exact amount of tape remaining for tapes 30 minutes or less, or for tapes over 120 minutes in length.

D4743-4743S P26-35 (030318 C-lot).p65 2003/03/18, 15:2834

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : consumerproducts@panasonic.com

Copying Your Tapes (Dubbing)

Connection

VCR/ Camcorder (Hi-Fi)

VIDEO

AUDIO

OUT

Connect VIDEO OUT terminal on Playing VCR to VIDEO IN terminal on DECK. To monitor the dubbing, also connect TV as shown.

Connect “L” and “R” AUDIO OUT terminals on Playing VCR to “L” and “R” AUDIO IN terminals on DECK.

In place of Playing VCR, you can use other equipment, such as a Camcorder. Simply connect the unit’s Audio/Video outputs to DECK.

DVD/VCR DECK

VIDEO

AUDIO

OUT

IN FROM ANT.

IN 1

VHF/UHF

OUT TO TV

Playing (Source) VCR Recording (Editing) DECK

VHF/ UHF

Front of DECK

VIDEO IN 2

(Audio/Video In Terminals on the front of DECK are available)

L-AUDIO IN2-R

Insert a pre-recorded tape.

1 2

Press PLAY, then PAUSE/STILL

immediately to enter PLAY/PAUSE mode.

Press PLAY to start dubbing. Playing VCR starts playback.

Press STOP to stop dubbing.

To Monitor Dubbing on TV

1 Turn TV on and tune to the Recording

VCR channel (CH 3 or CH 4).

2 If Auto VCR/TV (see p.32) is set to

“OFF,” press VCR/TV on the remote to be VCR mode.

Note

Caution:• Unauthorized exchanging and/or copying of copyrighted recordings may be

The operation of steps 4 and 5 must be done on the playing and recording VCRs at the same time.

• Dubbing tapes protected with Copy Guard will result in poor quality recordings.

• Please note that some tapes cannot be dubbed on DECK. Also, it is not possible to dub DVD/ Video CD/ CD to VHS tapes using DECK.

Insert a blank tape with record tab.

Press INPUT to set DECK Input mode to LINE for Video Input.

(See “Selecting the Input Mode” below.)

Press REC, then PAUSE/STILL immediately to enter REC/PAUSE mode.

Press PAUSE/STILL to start dubbing. DECK starts recording.

Press STOP to stop dubbing.

Selecting the Input Mode

Method 1: Press INPUT repeatedly.

Method 2: Press CH / .

Press

•“L1” or “L2” lights up on Multi Function Display (about 4 seconds) when LINE1 or LINE2 is selected.

• LINE1: For rear audio/video connection. LINE2: For front audio/video connection.

Channel Number

Display will change as below.

LINE1

LINE2

(CABLE)

125

↔↔

↔ LINE1

↔↔

(TV)

↔↔

↔ LINE2

↔↔

Press

Operation

VCR

D4743-4743S P26-35 (030318 C-lot).p65 2003/03/18, 15:2835

3 ESP

SELECT END

AUDIO

1 ENG

SELECT END

AUDIO

ENG FRA DEU ITA ESP NLD

English French German Italian Spanish Dutch

SVE NOR DAN POR RUS JPN

Swedish Norwegian Danish Portuguese Russian Japanese

CHI KOR MAL VIE THA

∗

Chinese Korean Malay Vietnamese Thai Other

Disc Operation

Subtitle Language (DVD only)

You can select a different subtitle language (if offered) than the one set at the Settings for DVD Operation. (See p. 47.)

Press

in Play mode to display the subtitle selection on-screen.

SUB TITLE

• Display disappears after 5 seconds.

• When no subtitles are offered, “-” will be displayed instead of

the language number.

Press

Te amo

Subtitle language being played back (see chart, right).

to select a language.

Press

to select “ON” or “OFF.”

Notes

• If after several presses of the button the language does not change, language selection is not offered on the disc.

• When disc is removed, subtitles revert to initial setting language. If the initial language is not recorded on the disc, the disc’s priority language will appear.

Ready Checklist

Please read “Basic DVD Operation” on page 22.

[Subtitle language] [Audio sound track language]

Audio Soundtrack Language (DVD only)

You can change the audio soundtrack language, selected at the Settings for DVD Operation, to a different language if available. (See p. 47.) (This operation works only with discs on which multiple audio soundtrack languages are recorded.)

Press

AUDI O: 1 ENG

Dolby Digital 3/2.1ch

Hello

SELECT

END

:AUDIO

AUDI O: 3 ESP

Dolby Digital 3/2.1ch

Hola

SELECT

END

:AUDIO

Audio soundtrack language being played back (see chart, above right).

D4743-4743S P36-60 (030318 C-lot).p65 2003/03/18, 15:2836

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : consumerproducts@panasonic.com

AUDIO

in Play mode to display the audio selection on-screen.

• Display disappears after 5 seconds.

Audio attribute 1 type, sampling frequency, bit No. of the disc or number of speaker channel.

Press

to select desired language.

• Change the No. by pressing , and press

SET

[Audio attribute 1 type, sampling frequency, bit No. of the disc (see p. 48.)]

LPCM

Dolby Digital

DTS

96 kHz

48 kHz

1c h - 5.1 ch 1 ch - 5.1 ch

20 bit 24 bit

Linear PCM disc

Dolby Digital disc DTS disc

16 bit

Notes

• If, after several presses of the

AUDIO button the language does not change, language selection is not offered on the disc.

• When disc is removed, language

reverts to initial setting. If this language is not recorded on the disc, the language recorded will be heard.

• DVD Karaoke (1 vocal) VOCAL ON VOCAL OFF

• DVD Karaoke (2 vocals) VOCAL V1 VOCAL V2 VOCAL V1+V2 VOCAL OFF

• Video CD LR L R

Important: if a remote control button does not work when pressed,

press the DVD button on the remote and try the button again.

When appears on the screen while a button is being operated, it means that the corresponding operation is prohibited by DECK or the disc.

ANGLE Indicator

Notes

• The ANGLE Indicator lights up on DECK when a scene recorded at different angles is detected.

• The angle number can be set beforehand so that the angle is switched whenever the ANGLE Indicator lights up.

SELECT

SET

ZOOM

SUB TITLE

ANGLE AUDIO

Notes

• The subtitle cannot be enlarged nor

can it’s position be changed.

• The picture zoom feature does not

work with a Video CD.

• During picture zoom, “ZOOM1” or

“ZOOM2” appears on-screen for 5

second.

• Zooming, on some discs, may result

in poor picture quality, or may not operate at all.

Multiple Angle Viewing (DVD only)

DVDs may contain scenes shot from multiple camera angles allowing the same scene to be viewed at different angles. You can view these angles, if available, using the ANGLE button.

Press

ANGLE

SELECT :

Number of angle being played back.

Vocal Selection for Karaoke Discs

Press

AUDIO

to display the audio screen.

SELECT : END :AUDIO

in Play mode to display the angle selection on-screen.

• Display disappears after 5 seconds.

Press

to select the desired angle.

(DVD/Video CD)

in Play mode

Press (or ) to select as shown below, and press (DVD only)

(or ) to set.

Picture Zoom (DVD only)

You can enlarge specific portions of a picture and select the zoom ratio using the ZOOM button during DVD playback.

Press

ZOOM

as follows.

• You can enlarge the center portion of the image to one of 2 magnifications.

■ Use the , , and buttons to move the position

up, down, left and right.

repeatedly to change display

Operation

DVD

D4743-4743S P36-60 (030318 C-lot).p65 2003/03/18, 15:2837

Disc Operation (continued)

Title Menu (DVD only)

Some DVDs have more than one title, e.g. movies. If the disc offers a title menu, you can select the desired title number. (Operation may vary according to the disc.)

Press

TITLE

T I TLE MENU

Dogs

Love

Cas t l es

in Play mode to display the title screen.

i r

T I TLE MENU

Cas t l es

Dogs

Love

B i rds

of the world

i r

Press or

NUMBER keys

to select a title, and

press

to start playing.

•“Pressing not necessary when using

NUMBER keys.

SET

PLAY

” is

DVD Menu (DVD only)

DVDs may offer a special menu. This menu may include guides to unique contents, audio/subtitle languages, etc. Although contents and operation may vary, the following steps show basic steps for using the menu.

Press

DVD MENU

1 . SUBT I TLE

2 . AUD

3 . ANGLE

DVD MENU

1 . SUBT I TLE

2 . AUD

3 . ANGLE

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : consumerproducts@panasonic.com

in Play mode to display DVD MENU.

Press or

NUMBER keys

to select an item, and

press

SET

PLAY

to perform.

•“Pressing not necessary when using

NUMBER keys.

Repeat step 2 if there is more than one menu.

SET

PLAY

” is

NUMBER keys

CLEAR

ACTION MENU

SELECT

SET PLAY

STOP

TITLE

D4743-4743S P36-60 (030318 C-lot).p65 2003/03/18, 15:2838

PROGRAM PLAY

Important: if a remote control button does not work when pressed,

press the DVD button on the remote and try the button again.

Program Play (Video CD/CD only)

You can program specific tracks and order of play.

Press

Notes

• Up to 15 tracks can be programmed.

•“ ” or “ ” (depending on disc) indicates additional

PROGRAM PLAY screen. Press for next or previous screen.

• To clear the last program one by one

Press to move to “CLEAR LAST” and press also clears last program.)

• To clear all programs

Press to move to “CLEAR ALL” and press

SET.

is turned off or the disc is removed.)

ACTION

to display DVD MAIN MENU.

DVD MAIN MENU

DI SC LANGUAGES AUDIO OUTPUT ST IL L MODE : AUTO TV MODE : 4: 3 L e tt er b ox PARENTAL LOCK :

PLAY MODE

SELECT : SET : SET END : ACTI ON

PROGRAM PLAY

RANDOM PLAY

LEVEL 8

PLAY MODE

Press

to select “PLAY MODE,” and

press

SET

to display.

Press

to select “PROGRAM PLAY,” and

SELECT : SET : SET END : ACTI ON

PROGRAM PLAY

DI SC PROGRAM

1 61116 5 8

2 7 12 17 15 6 3 8 13 18 1 13 4 9 14 19 3 2 5101520 2

CLEAR LAST

CLEAR ALL START SELECT : SET : SET END : ACTI ON

• Repeat step 4 to select another track.

• The selected track is added on the right side.

PROGRAM PLAY

DI SC PROGRAM

1 61116 5 8

2 7 12 17 15 6 3 8 13 18 1 13 4 91419 3 2 5101520 2

CLEAR LAST

CLEAR ALL START SELECT : SET : SET END : ACTI ON

SET

. (Pressing

(Programs are also cleared when the power

press

SET

to display.

Press

to select a track number (Track numbers on disc are displayed.), and

press

SET

Press

to select “START,” and

press

SET

to start play of programs in the sequence selected.

• To cancel, press during play, then press

CLEAR

on remote control

STOP

Ready Checklist

DECK is in DVD mode, press DVD. Video CD or CD is inserted.

Program Repeat Play (Video CD/CD only)

Do operation steps 1 through 5

at left on this page.

Press

DISPLAY

Information screen.

(Disc Information Screen)

TRACK : 1 VIDEO CD

PBC : OFF 01 :35 : 12

SET : SET NEXT : DISPLAY

Press

DISPLAY

DECK Information screen.

Press

SET

Cursor move to “OFF.”

(DECK Information Screen)

SET : SET END : DI SPLAY

Press to select “DISC.”

(DECK Information Screen)

PLAY REPEAT : DISC PROGRAM PLAY

SELECT : SET : SET END : DI SPLAY

Press

SET

Cursor move to “REPEAT.” To cancel, select “REPEAT : OFF” in step 5, then press

to display Disc

to display

to enter Select mode.

to set mode.

SET

Operation

DVD

D4743-4743S P36-60 (030318 C-lot).p65 2003/03/18, 15:2839

Disc Operation (continued)

Random Play (Video CD/CD only)

Tracks are played in a random order.

Press

ACTION

to display DVD MAIN MENU.

DVD MAI N MENU

DI SC LANGUAGES

AUDIO OUTPUT ST IL L MODE : AUTO TV MODE : 4 :3 Le t te r bo x PARENTAL LOCK :

PLAY MODE

SELECT : SET : SET END : ACT ION

PLAY MODE

PROGRAM PLAY

RANDOM PLAY

SELECT : SET : SET END : ACT ION

LEVEL 8

Press

to select “PLAY MODE,” and

press

SET

to display.

Press

to select “RANDOM PLAY,” and

press

SET

to begin random play.

• To cancel, press during play, then press

CLEAR

STOP

Ready Checklist

DECK is in DVD mode, press DVD.

*Important: If a remote control button does not work when pressed, press the DVD button on the remote and try the button again.

CLEAR

ACTION

SELECT

SET

STOP

VOLUME ADJUST

Setting the VOLUME ADJUST

Some DVDs are recorded in lower than average volume levels. For these DVDs, this DECK can be set so that the average volume is increased.

Press

VOL.ADJ

•“ON” or “OFF” lights up on Multi Function Display (about 3 seconds) when press VOL.ADJ.

repeatedly to change “ON”

VOLUME ADJUST “OFF”

Some DVD

[Volume level is low]

Volume is the original level.

•“ON” is set ..... When a DVD is played back, the average volume is increased.

•“OFF” is set .... The volume level recorded on the disc is played back just as it is.

Notes

• This feature is available only for Dolby Digital sound tracks.

• When audio equipment is connected, setting the Sound Output level to “OFF” is recommended.

• If the sound becomes abnormal while playing a disc, set the Sound Output level to “OFF.”

D4743-4743S P36-60 (030318 C-lot).p65 2003/03/18, 15:2840

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : consumerproducts@panasonic.com

↔↔

↔ “OFF.”

↔↔

VOLUME ADJUST “ON”

Volume level is increased

when played back.

DVD Operation using On-Screen Displays

When

DISPLAY

disc information (title/chapter/track number, elapsed playing time) and DECK information (repeat play, play mode).

Press

to display “On-Screen Displays.”

• Each press of

display as follows. (Refer to p. 42.)

Note

DISPLAY

TITLE MENU is displayed.

Press (or )

to select

press

is pressed, On-Screen Displays show

DISPLAY

button does not function while DVD

in Play or Stop mode

DISPLAY

changes the on-screen

Selected disc information

➡

Selected DECK information

➡

Normal Screen

an item, and

SET

Ready Checklist

DECK is in DVD mode, press DVD.

NUMBER keys

CLEAR

SELECT

SET

Press or

to select the setting, and

press

SET

TRACK : 12 V IDEO CD

PBC : OFF 00 :12 : 34

SET : SET NEXT : D ISPLAY

NUMBER keys

• When numbers are displayed (e.g. title number), are also available.

• If the number entered is not on the disc, the entry will have no effect. Re-enter the correct number.

• For more details, refer to the disc operation information.

To return to normal screen, press

DISPLAY

NUMBER keys

CLEAR

repeatedly.

DISPLAY

Notes

• When

• When appears on the screen

DISPLAY

pressed during playback of a Video CD with Playback control,

NUMBER keys

on the displayed screen. In this case, press remove the displayed screen.

while a button is being operated, it means that the corresponding operation is prohibited by DECK or the disc.

button is

are not available

DISPLAY

again to

Operation

DVD

D4743-4743S P36-60 (030318 C-lot).p65 2003/03/18, 15:2841

DVD Operation using On-Screen Displays (continued)

PLAY

REPEAT : CHAPTER

PLAY

REPEAT : DISC

RANDOM PLAY

ENTER : 0 - 9 SET : SET NEXT : DISPLAY

T ITLE : 1 DVD CHAPTER : 12 01:

--:--

SELECT : SET : SET NEXT : DISPLAY

T ITLE : 1 DVD

CHAPTER : 12 01: 12 :55

SET : SET NEXT : DISPLAY

TRACK : 1 VIDEO CD

PBC : OFF 01 :35 : 12

Detailed Descriptions of each On-Screen Display

■■

■ Disc information screen (for DVD)

■■

1. TITLE No.

• Select “TITLE”, and press

• Change the No. by pressing or

SET

NUMBER keys

, and press

2. CHAPTER No.

• Select “CHAPTER”, and press

• Change the No. by pressing or

SET

NUMBER keys

, and press

3. Disc currently being played

4. Elapsed playing time

The screen may be changed by selecting the elapsed time.

• Select the elapsed playing time (“xx:xx:xx”), and press

• Change the elapsed time by pressing

NUMBER keys

. Hours ➛ Minutes ➛ Seconds are entered in order. If the time entered is not on the disc, the entry will have no effect. Re-enter the correct time. e.g., press 0 - 1 - 2 - 3 - 4 - 5 for 01 : 23 : 45.

Hour Minutes Seconds

• This function does not work with some discs.

■■

■ Disc information screen (for Video CD/ CD)

■■

A. TRACK No.

• Select “TRACK”, and press

• Change the No. by pressing or

SET

NUMBER keys

, and press

B. Playback control ON/OFF

[Video CD with playback control only]

ON Video CD menu play is displayed. OFF Video CD menu play is not displayed.

C. Disc currently being played

Video CD CD

D. Elapsed playing time

• Track No. and the elapsed playing time are not displayed during play started from menu of

Note

Video CDs with playback control.

• When appears on the screen while a button is being operated, it means that the corresponding operation is prohibited by DECK or the disc.

■■

■ DECK information screen (for DECK)

■■

a. Repeat Play

• Select “REPEAT”, and press

SET

• Change the desired mode during play by pressing , and press

DVD REPEAT CHAPTER REPEAT TITLE REPEAT OFF Video CD/CD REPEAT TRACK REPEAT DISC REPEAT OFF

b. Play mode [Video CD/ CD only] (See p. 39 or 40.)

PROGRAM PLAY program play RANDOM PLAY random play

----

normal play

For your reference

•

CHAPTER/TITLE REPEAT PLAY (DVD)

CHAPTER REPEAT

Note

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : consumerproducts@panasonic.com

CURRENT PLAYBACK POSITION

TITLE

chapter

TITLE REPEAT

NORMAL PLAY

chapter

• For repeat play in VCR mode, see p. 32.

•

TRACK/DISC REPEAT PLAY (Video CD/CD)

TRACK REPEAT

DISC REPEAT

NORMAL PLAY

SET

1 2

If SET is pressed while making entries, unit returns to the condition it was in before entries were made.

A B

SET

CURRENT PLAYBACK POSITION

track

3 4

C D

D4743-4743S P36-60 (030318 C-lot).p65 2003/03/18, 15:2842

MP3/WMA/JPEG Playback Operation

This unit can play MP3/WMA/JPEG format CD-R or CD-RW recorded for personal use on a PC, etc. Some discs may not play due to the condition of the recording.

Press

POWER

Press

OPEN/CLOSE

then place an MP3/WMA/JPEG disc into

on the remote or DECK.

the disc tray.

Press

OPEN/CLOSE

• MP3/WMA/JPEG menu is displayed.

• Playback starts automatically

(except JPEG files).

• CD directory is displayed.

Function

Status

Folder area

(Current folder

appears green.)

:MP3 file :WMA file

:Folder :Parent folder :JPEG file

ROOT

TECHNO

POPS

AZZ

• Select file (During STOP mode)

1)Press to select an MP3/WMA file ( / ).

2)Press to select a JPEG file ( ).

3)Press

• Select folder (During STOP mode)

1)Press to select a folder ( ).

2)Press

• Select parent folder (During STOP mode)

1)Press to select a folder ( ).

2)Press

Press

MENU. (➛ Press

PLAY

ROOT . .

END_W

TECHNO

POPS J

AZZ

PLAY MODE : NORMAL

PLAY MODE

(Diagram left shows CD directory structure as displayed in example OSD above.)

END_W

ALTZ DD_CUB I C N

CTURNE

➡ MP3/WMA Playback (see right)

➡ JPEG Playback (see p. 44)

(previous) to skip a file/folder page (7files) in the File area.

in the folder.

directory display.

Notes

• Only File (not Folder) area operation is possible.

• Files are displayed in the following order:

(!...0,1....9,A,B......Z).

SKIP

SET

to display files/folders contained

SET

to make changes to the previous

ACTION

to close.

00 : 00 :

Counter

Parent folder

File area

(Selected file/ folder is highlighted. Titles are displayed up to 11 characters.)

SKIP

ALTZ

DD_

CUB I C

NOCTURNE

NORN

| (next) or |

to return to the DVD MAIN

ACTION

again to return

to the MP3/WMA/JPEG MENU.)

MP3/WMA Playback

Do steps 1~3 on left.

Press to select an MP3/WMA file (

(During STOP mode)

Press

SET

PLAY

■ Forward/Reverse Search Press

FF/SLOW+

Press

PLAY

• Search speed, slow at first, increases with each

additional press of the button up to 5 levels.

■ Forward/Reverse Track Skip Press

Each press skips a track.

• If pressed within first 3 seconds of playback,

skips to the previous track. If over 3 seconds, returns to top of track. (|

• Put DECK in Stop mode before performing

folder/file selection (see step 4.)

■ Pause Press Press

Press

The MP3/WMA/JPEG MENU is closed

automatically.

Note

■ Select PLAY MODE [MP3/WMA Playback]

(During STOP mode)

1) Press to move cursor to

PLAY MODE.

2) Press to select the desired PLAY

MODE (see below).

[PLAY MODE] NORMAL:

All MP3/WMA files are selected and played back one time only.

SINGLE REPEAT:

The selected MP3/WMA file is played back repeatedly.

FOLDER REPEAT:

The MP3/WMA files contained in the selected folder are played back repeatedly. However, folders below the selected folder are not played back.

DISC REPEAT:

All MP3/WMA files are played back repeatedly.

Important:

if a remote control button does not work when pressed, press the DVD button on the remote and try the button again.

to release.

SKIP

| or |

PAUSE PLAY

to release.

STOP

OPEN/CLOSE

• Copyright protected files and files containing errors cannot be played back. The DECK skips to the next file.

to start playback.

REW/SLOW-

SKIP

during play.

to stop play.

during play.

SKIP

only.)

to eject the disc.

Operation

DVD

D4743-4743S P36-60 (030318 C-lot).p65 2003/03/18, 15:2843

MP3/WMA/JPEG Playback Operation (continued)

JPEG Playback

You can play back JPEG images. Displayable Image Size: 32x32~7680x7680 pixels

• Some JPEG format may not be played

Note

Do steps 1~3 on page 43.

■ Returned on the MP3/WMA/JPEG MENU

■ Next/Previous Search

■ Start Slide-show ➡ Press

■ Enlarging an image ➡ Press

■ Rotating an image ➡ Press

back.

Press to select an JPEG file ( ).

Press

SET

PLAY

Selected JPEG file is displayed.

[JPEG Playback Screen]

➡ Press

REW/SLOW-

Press

JPEG MENU.

STOP

. (See p. 43)

SKIP

| or |

. (below)

STOP

to return to the MP3/WMA/

SKIP

FF/SLOW+

ZOOM

ANGLE

. (P. 45) . (P. 45)

■ Select PLAY MODE [JPEG Slide-show]

(During STOP mode) (See p.43)

1) Press to move cursor to

PLAY MODE.

2) Press to select the desired PLAY

MODE (see below).

[PLAY MODE] NORMAL:

All JPEG files are selected and played back one time only.

SINGLE REPEAT:

The selected JPEG file is played back repeatedly.

FOLDER REPEAT:

The JPEG files contained in the selected folder are played back repeatedly. However, folders below the selected folder are not played back.

DISC REPEAT:

All JPEG files are played back repeatedly.

JPEG Slide-show

(During JPEG Playback.)

JPEG files are displayed automatically (about every 3 seconds) as a slide-show.

Press

Image changes every 3 seconds.

■ Cancel slide show

■ Still picture

■ Forward/Reverse File Skip

D4743-4743S P36-60 (030318 C-lot).p65 2003/03/18, 15:2844

FF/SLOW+

➡ Press

➡ Press ➡ Press

➡ Press

Press MENU.

STOP

JPEG MENU. (See p. 43)

STILL

PLAY

SKIP

Each press skips a file.

ACTION

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : consumerproducts@panasonic.com

REW/SLOW-

to return to the MP3/WMA/

(only SLIDE).

to release.

| or |

to return to the DVD MAIN

SKIP

Operation can be done when files are in order, such as in the diagram below.

ROOT

01 PIC

REW/SLOW-

FF/SLOW+

AAA DDD TTT UUU VVV WWW ZZZ

REW/SLOW-

FF/SLOW+

ACTION

STOP

REW/

SLOW-

FF/

SLOW+

STILL

JPEG Zoom

(During JPEG Playback.)

You can enlarge specific portions of a JPEG picture and select the zoom ratio using the ZOOM button on the remote during JPEG Playback screen.

Set Zoom size.

Press

ZOOM

repeatedly to change display as

STOP

to return to the MP3/WMA/JPEG MENU.

X 1.5 (ZOOM 1) X 2.0 (ZOOM 2)

1st press

SELECT

SET

PLAY SKIP SKIP

ZOOM ANGLE

follows.

Press

➡

• You can enlarge the center portion of the image to one of 2 magnifications.

• Operation can be done during Rotation (below).

X 1.0 (ORIGINAL)

■ Use the , , and buttons to move the

position up, down, left and right. (Position cannot be changed on X1.0 ORIGINAL images.)

JPEG Rotation

(During JPEG Playback.)

You can rotate a JPEG picture using the ANGLE button on the remote during JPEG Playback screen. (The JPEG picture will be rotated 90 ° clockwise.)

Set rotation.

Press

ANGLE

as below.

Press

➡

MENU.

• Operation can be done during Zoom (above).

• The vertical/horizontal ratio of rotated JPEG

images may vary when they are displayed.

1st press 2nd press 3rd press

repeatedly to change display

STOP

to return to the MP3/WMA/JPEG

2nd press

3rd press

Operation

DVD

MPEG Layer-3 audio decoding technology licensed from Fraunhofer IIS and Thomson multimedia.

Windows Media, and the Windows logo are trademarks, or registered trademarks of Microsoft Corporation in the United States and/or other countries. WMA is a compression format developed by Microsoft Corporation. It achieves the same sound quality as MP3 with a file size that is smaller than that of MP3.

D4743-4743S P36-60 (030318 C-lot).p65 2003/03/18, 15:2845

4th press

DVD Lock Feature

*Important: If a remote control button does not work when

pressed, press the DVD button on the remote and try the button again.

You can prevent playback of DVDs of a specific rating level which may be unsuitable for children.

• Some DVDs are encoded with a rating level. If the disc rating is higher (stricter) than the one you preset, playback will be prohibited.

DVD Lock (DVD only)

A 4-digit code must be entered to view a blocked program or change rating settings.

Press

ACTION

to display DVD MAIN MENU.

DVD MAIN MENU

DI SC LANGUAGES AUDIO OUTPUT

ST IL L MODE : AUTO TV MODE : 4:3 Letterbox

PARENTAL LOCK : LEVEL 8

SELECT : SET : SET END : ACTI ON

ENTER 4-D I G I T

----

ENTER : 0 END

: ACT I O

To Make Corrections

Press repeatedly to

move the cursor.

Press

NUMBER keys

make the correction.

LEVEL 0 : LOCK ALL, Playback of all DVDs, CDs, Video

LEVEL 1 : mature theme DVDs LEVEL 2 : DVDs expressly for children can be played back. LEVEL 3 to 7 : DVDs for general audiences/children can be

LEVEL 8 : NO LIMIT: (Factory preset)

CDs, MP3, WMA and JPEG is prohibited. (Use to prohibit play of mature theme DVDs not encoded with rating level.)

All DVDs can be played back.

Press

to select “PARENTAL LOCK,” and

press

SET

to display.

1) Press

CODE

2) Enter same secret code

3) Press

• Step 2) not necessary when changing rating or secret code.

• Take care that you are not

observed entering the secret code.

NUMBER keys

to enter your secret code.

again for confirmation.

SET

to display.

Press

to select rating level, and

press

SET

to select “LOCKED” or “UNLOCKED.”

played back. (DVDs with mature content are prohibited.)

Ready Checklist

DECK is in DVD mode, press DVD.

Caution

Discs not encoded with rating level will play even if the jacket states it is for mature audiences. For these discs, the DVD Lock Ratings will not work.

YOUR SELECTI ON EXCEEDS THE

PLAYER S RATI NG LIMIT. DO YOU WANT TO CHANGE THE LIMIT?

YES

SELECT: SET : SET END : D ISPLAY

After DVD Lock is set and a blocked DVD is played, this message will appear. The message may differ depending on the disc.

To continue viewing a blocked program for now,

Press to select “YES” and

SET. Then, enter your 4 digit secret code (see step 3 left).

When “NO” is selected, blocked programs cannot be viewed.

PROGRAM RATING EXCEEDED

Change your secret code

• You will need your current code. Do steps 1 ~ 2 left. Enter current secret code.

Press

CLEAR

Do step 4 to enter new code.

to clear the code.

D4743-4743S P36-60 (030318 C-lot).p65 2003/03/18, 15:2846

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : consumerproducts@panasonic.com

Note

• DO NOT forget your secret code.

Settings for DVD Operation

Press

ACTION

to display DVD MAIN MENU.

DVD MAIN MENU

DI SC LANGUAGES

AUDIO OUTPUT

ST IL L MODE : TV MODE : 4:3 Letterbox PARENTAL LOCK :

SELECT : SET : SET END : ACTI ON

AUTO

LEVEL 8

Press

to select an item, and

press

SET

DISC LANGUAGES (See below)

All languages offered on the disc can be set. If the language not offered is set, the original disc language will be selected.

AUDIO OUTPUT (See p. 48.)

You can set the audio output that comes from the digital audio output terminal.

STILL MODE (See p. 49.)

To select “FIELD” (Field still) or “FRAME” (Frame still) to prevent jitter or make small text or fine patterns clearly visible in a still picture. When “AUTO” is set “FIELD” or “FRAME” is selected automatically.

TV MODE (See p. 49.)

To select whether the video material for a widescreen will be played back in the Pan & Scan style, Letterbox style or 16 : 9 style.

Disc Languages (DVD only)

To select and set the language of the audio soundtrack, subtitles, or title/DVD menus for all discs to be played.

DVD MAIN MENU

DI SC LANGUAGES

AUDIO OUTPUT

ST IL L MODE : TV MODE : 4:3 Letterbox PARENTAL LOCK :

SELECT : SET : SET END : ACTI ON

AUDIO : English

SUBT ITLE : AUTO

MENUS : English

SELECT : SET : SET END : ACTI ON

Press

MENU and go to step 2 to setup another

AUTO

LEVEL 8

DI SC LANGUAGES

ACTION

item. Or, press

ACTION

Press

to select “DISC LANGUAGES,” and

press

SET

to display screen.

Press

to select an item, and

press

SET

repeatedly for desired language. (Please refer right.)

to redisplay DVD MAIN

twice to exit.

Once initial settings are done, they remain in memory (even after power off) until changed. This means DECK will operate under the same conditions (especially DVDs) each time.

Ready Checklist

DECK is in DVD mode, press DVD.

NUMBER keys

CLEAR

ACTION

SELECT

SET

“AUDIO” selections

(Factory preset: English)

To select the audio soundtrack language.

English/Spanish/French/Japanese Original: Original disc language

OTHER ✱✱✱✱: Other language selection*

“SUBTITLE” selections

(Factory preset: AUTO)

To select the subtitle language.

AUTO: Same language selected

for “AUDIO”

• If language set for “AUDIO” is used in

playback, subtitles will not appear.

• If another language is used during

playback, the subtitles will appear in the language selected at “AUDIO” setup.

English/Spanish/French/Japanese OTHER ✱✱✱✱: Other language selection*

“MENUS” selections

(factory preset: English) To select the language used in title menus or DVD menus.

English/Spanish/French/Japanese OTHER ✱✱✱✱:

To enter OTHER ✱✱✱✱

Other language selection*

code

number,

Press

NUMBER keys

language codes on page 50). To make corrections, press repeatedly to delete language code number, and correct.

*1If the selected language is not offered,

the original disc language is selected.

(Please refer to

Operation

DVD

D4743-4743S P36-60 (030318 C-lot).p65 2003/03/18, 15:2847

Settings for DVD Operation (continued)

Audio Output

Select the digital output to be output from the optical digital audio output connector of DECK.

ACTION

Press

to display DVD MAIN MENU.

DVD MAI N MENU

DI SC LANGUAGES

AUDIO OUTPUT

ST IL L MODE : AUTO TV MODE : 4:3 Letterbox PARENTAL LOCK :

SELECT : SET : SET END : ACT ION

AUDI O OUTPUT

LPCM(DVD) : OFF

Dolby Digital : Bitstream dts : Bitstream DRC : OFF

SELECT : SET : SET END : ACT ION

■■

■ “LPCM (DVD)” selections

■■

OFF: Linear PCM of less than 48 kHz/16 bit is

output. When playing DVDs recorded in linear PCM of over 48 kHz/20 bit, no digital audio is output. (Factory preset)

PCM: When playing DVDs recorded in linear PCM of

48 kHz/20 bit/24 bit or more, digital audio converted to 44.1 kHz/16 bit or 48 kHz/16 bit is output. (Digital output of PCM audio is restricted to 48 kHz/16 bit or below for copyright protection.)

■■

■ “Dolby Digital” selections

■■

Bitstream: Dolby Digital bitstream (1 ch - 5.1 ch) is

PCM: When you have connected a amplifier that

■■

■ “dts” selections

■■

Bitstream: DTS bitstream is output. (Factory preset) PCM: When you have connected a amplifier that

■■

■

“DRC (Dynamic Range Compression)”

■■

output. (Factory preset)

doesn’t have a built-in Dolby Digital decoder.

doesn’t have a built-in DTS decoder.

selections

OFF: Normal audio range is selected. (Factory preset) ON: For dynamic sound even at low volume, this

is useful for late-night listening. [Dolby Digital DVDs only].

LEVEL 8

Press

to select “AUDIO OUTPUT,” and

press

to display screen.

Press

to select an item, and

press

repeatedly for output. (See below.)

SET

Ready Checklist

DECK is in DVD mode, press DVD.

Type of amplifier to be connected

No amplifier is connected AV amplifier (with digital

audio input connector) without Dolby Digital/DTS decoder

AV amplifier including Dolby Digital decoder

AV amplifier including Dolby Digital/DTS decoder

• Make settings according to amplifier connected to optical audio output as shown in above table.

*1 When connecting an amplifier (with an

optical digital input connector) which does not contain the Dolby Digital or DTS decoder, be sure to select “PCM”. If “Bitstream” is selected, starting DVD play may cause such a high level of noise as to be harmful to your ears and damage the speakers.

*2 When a DTS decoder is connected, please

select “Bitstream” in “dts”.

Recommended setting

LPCM

(DVD)

PCM

Dolby

Digital

PCM*

Bitstream

DTS

PCM*

PCM

Bitstream

Press

ACTION

MENU and go to step 2 to setup another

to redisplay DVD MAIN

item. Or, press

D4743-4743S P36-60 (030318 C-lot).p65 2003/03/18, 15:2848

ACTION

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : consumerproducts@panasonic.com

twice to exit.

TILLLL

MODE

: AUTO

*Important: If a remote control button does not work when pressed,

press the DVD button on the remote and try the button again.

Still Mode

Set to reduce jitter in a displayed still picture or a motion picture.

ACTION

Press

to display DVD MAIN MENU.

DVD MAI N MENU

DI SC LANGUAGES

AUDIO OUTPUT

STI

MODE

TV MODE : 4 :3 Le t te r bo x PARENTAL LOCK :

SELECT : SET : SET END : ACT ION

AUTO: “FIELD” (Field still) or “FRAME” (Frame still) is

FIELD: “FIELD” (Field still) is always selected.

FRAME:“FRAME” (Frame still) is always selected.

Press

to exit this mode.

: AUTO

LEVEL 8

automatically selected during the still mode. (Factory preset)

This setting will reduce jitter when compared with “AUTO” on some discs.

Some texts and fine patterns will be seen clearly when compared with “AUTO” on some discs.

ACTION

Press

to select “STILL MODE,” and

SET

press

repeatedly

for mode. (See below.)

TV Mode

Set the screen display style for wide-screen video material playback.

Press

ACTION

to display DVD MAIN MENU.

DVD MAI N MENU

DI SC LANGUAGES

AUDIO OUTPUT ST IL L MODE : AUTO

TV MODE : 4 :3 Le t te rb o x

PARENTAL LOCK :

SELECT : SET : SET END : ACT ION

4:3 Pan & Scan (Factory preset) :

Wide-screen video data is played in Pan & Scan style (left and right of screen is trimmed.)

• Video data not formatted in Pan & Scan will play in letterbox style.

4:3 Letterbox :

Wide-screen video data is played in Letterbox style (top and bottom of screen has black margin).

16:9 :

Set “16:9” when using Wide-screen TV.

LEVEL 8

Press

to select “TV MODE,” and press

SET

repeatedly for mode. (See below.)

ACTION

SELECT

SET

Example

• Pan & Scan (Factory preset)

• Letterbox

Operation

DVD

Press

ACTION

to exit this mode.

D4743-4743S P36-60 (030318 C-lot).p65 2003/03/18, 15:2849

Language Code List

Enter the appropriate code number for the initial settings “AUDIO”, “SUBTITLE” and/or “MENUS” (see p. 47).

Code Language

6565 Afar 6566 Abkhazian 6570 Afrikaans 6577 Ameharic 6582 Arabic 6583 Assamese 6588 Aymara 6590 Azerbaijani 6665 Bashkir 6669 Byelorussian 6671 Bulgarian 6672 Bihari

Bengali; Bangla

6678 6679 Tibetan 6682 Breton 6765 Catalan 6779 Corsican 6783 Czech 6789 Welsh 6865 Danish 6869 German 6890 Bhutani 6976 Greek 6978 English 6979 Esperanto 6983 Spanish 6984 Estonian 6985 Basque 7065 Persian 7073 Finnish 7074 Fiji

Code Language

7079 Faroese 7082 French 7089 Frisian 7165 Irish 7168 Scots Gaelic 7176 Galician 7178 Guarani 7185 Gujarati 7265 Hausa 7273 Hindi 7282 Croatian 7285 Hungarian 7289 Armenian 7365 Interlingua 7378 Indonesian 7383 Icelandic 7384 Italian 7387 Hebrew 7465 Japanese 7473 Yiddish 7487 Javanese 7565 Georgian 7575 Kazakh 7576 Greenlandic 7577 Cambodian 7578 Kannada 7579 Korean 7583 Kashmiri 7585 Kurdish 7589 Kirghiz 7665 Latin

Code Language

7678 Lingala 7679 Laothian 7684 Lithuanian

Latvian, Lettish

7686 7771 Malagasy 7773 Maori 7775 Macedonian 7776 Malayalam 7778 Mongolian 7779 Moldavian 7782 Marathi 7783 Malay 7784 Maltese 7789 Burmese 7865 Nauru 7869 Nepali 7876 Dutch 7879 Norwegian 7982 Oriya 8065 Panjabi 8076 Polish

Pashto, Pushto

8083 8084 Portuguese 8185 Quechua

Rhaeto-Romance

8277 8279 Romanian 8285 Russian 8365 Sanskrit 8368 Sindhi

Serbo-Croatian

8372 8373 Singhalese

Code Language

8375 Slovak 8376 Slovenian 8377 Samoan 8378 Shona 8379 Somali 8381 Albanian 8382 Serbian 8385 Sundanese 8386 Swedish 8387 Swahili 8465 Tamil 8469 Telugu 8471 Tajik 8472 Thai 8473 Tigrinya 8475 Turkmen 8476 Tagalog 8479 Tonga 8482 Turkish 8484 Tatar 8487 Twi 8575 Ukrainian 8582 Urdu 8590 Uzbek 8673 Vietnamese 8679 Volapük 8779 Wolof 8872 Xhosa 8979 Yoruba 9072 Chinese 9085 Zulu

D4743-4743S P36-60 (030318 C-lot).p65 2003/03/18, 15:2850

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : consumerproducts@panasonic.com

Warning and Instruction Displays

These displays will alert you to a missed operation or provide further instructions.

CautionOSD

Page

PLEASE SET CLOCK BY PRESSING ACTION KEY

PLEASE PREPARE FOR TIMER REC

CHECK CASSETTE RECORD TAB

NO CASSETTE

TO CANCEL TIMER REC HOLD DOWN STOP KEY FOR APPROX 3 SEC

VIDEO HEADS MAY NEED CLEANING PLEASE INSERT HEAD CLEANING CASSETTE OR REFER TO MANUAL

END : PLAY

VCR LOCK ACTIVATED

REMOTE CONTROL IS SET TO TV MODE USE VCR : VCR KEY USE DVD : DVD KEY

PLEASE CHECK THE DISC, AND FOR STAINS OR SCRATCHES ON DISC

THIS DISC MAY NOT BE PLAYED IN YOUR REGION

THIS TYPE OF DISC CANNOT BE PLAYED. PLEASE INSERT A DIFFERENT DISC

CANNOT PLAY THIS FILE

THIS FILE IS PROTECTED

IT IS PROHIBITED TO COPY DVD/VIDEO CD/CD TO VHS

If you attempt to set or review a Timer Recording and the Clock is not set...

If DECK is not in Stop mode or a cassette with record tab is not inserted 2 minutes before a Timer Recording is about to begin...

If you press REC on the remote control or DECK, and a cassette is inserted with no record tab...

If you press PLAY, FF, REW, or REC on the remote control or DECK without a cassette inserted...

If you press STOP or POWER during a Timer Recording... (visible in VCR mode only)

If head cleaning becomes necessary while playing back a tape...

If you press a function button other than STOP/ EJECT or POWER while DECK is in VCR Lock mode...

If you press an invalid key on the remote while in TV mode...

If you press PLAY, and DECK reads data from a stained or scratched disc in DVD mode.

Playback of a disc with different region number was attempted. Only discs marked region “1”, “ALL”, or those that include “1” are playable on this DECK.

An unusable disc is inserted in the DECK.

This file format cannot be played. (Appears during MP3/WMA/JPEG file playback)

This file is copyright protected and cannot be played back. (Playback is prohibited.) [WMA only]

If you press REC in DVD mode...

24 25

20 21

28 29 34

Information

For Your

D4743-4743S P36-60 (030318 C-lot).p65 2003/03/18, 15:2851

Before Requesting Service

Check the following points if you are having trouble with your DECK.

Power

No power…

Power turns itself off...

Recording & Playback

TV program cannot be recorded...

Timer recording cannot be performed…

There is no playback picture, or the playback picture is noisy or contains streaks...

During special effects playback, picture may contain some vertical jitter when using a TV with an Automatic Vertical Hold Control...

DECK cannot be controlled...

Remote Control

DECK cannot be remote controlled...

PROG buttons do not respond...

Correction

• Completely insert Power Plug into an AC outlet.

• Set POWER button to on.

• Make sure power source is active.

• Auto power-off (shutoff) occurs after about 5 min.

in DVD mode with no operation, or if there is no broadcast signal in TV or Playback mode. Turn the power back on. (pp. 23, 33)

Correction

• Check connections between DECK, external antenna, and TV.

• Check channel selections.

• Make sure your antenna system (CABLE or TV) is

correctly set. (Channels [p. 18])

• Make sure cassette record tab is intact. (p. 6)

• Confirm that clock is set to current time and date.

• Make sure Cable/DSS box (if used) is left on and

tuned to channel to be recorded.

• Set recording start/stop times correctly. (p. 24)

• Timer recording may not be performed or continued

if a power interruption occurs before or during a Timer Recording, even after power is restored.

• Select channel 3 or 4 on TV to match VCR output channel (3 or 4) (p. 16) or select LINE.

• Set VCR/TV selector to “VCR.”

• Adjust TRACKING control in either direction. (p. 6)

• Try Head Cleaning. (p. 6)

• Set TV’s Vertical Hold Control to MANUAL, then

adjust.

• Make sure DECK power is on.

• Check Remote batteries.

• Make sure VCR LOCK is set to off. (p. 33)

• Make sure Remote is in proper mode. (p. 28)

• Make sure Timer Recording is not in progress.

Correction

• Make sure DECK power is on.

• Make sure Remote is in VCR mode.

• Aim Remote Control directly at remote sensor on DECK. (p.9)

• Avoid any object blocking signal path.

• Check Remote batteries. (p. 4)

• Exposing DECK remote sensor to direct fluorescent

or outdoor light may cause signal interference.

• PROG functions are not available in COMPONENT Video Output and S-VIDEO OUT. Set TV to either RF IN or VIDEO IN. (p. 10)

• Check Remote batteries. (p. 4)

• Press VCR or DVD button for DVD/VCR mode. (p. 28)

D4743-4743S P36-60 (030318 C-lot).p65 2003/03/18, 15:2852

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : consumerproducts@panasonic.com

Check the following points if you are having trouble with your DECK.

DVD/ Video CD/ CD

Play fails to start even when PLAY is pressed...

Play starts but then stops immediately... Picture is distorted during rapid

advance or rapid reverse... No Forward/Reverse Scene Search

play... Play does not start even when title is

selected... Audio soundtrack and/or subtitle

language is not the one selected at the initial settings...

No subtitles...

Alternative audio soundtrack (or subtitle) language cannot be selected...

Angle cannot be changed...

Miscellaneous

Programs cannot be viewed on TV...

Video cassette cannot be inserted...

Video cassette ejects when a recording is started or the power is turned off for timer recording...

In Stop mode, the motor (CYLINDER) continues to rotate...

The disc cannot be removed..

Correction

• This DECK cannot play discs other than DVDs, Video CDs and CDs.

• The disc may be dirty and require cleaning.

• Be sure disc is installed with label side up.

• The picture will be somewhat distorted at times:

this is normal.

• Some discs may have sections which prohibit Forward/Reverse Scene Search. (p. 23)

• Confirm the “DVD LOCK” setting. (p. 46)

• If the audio soundtrack and/or subtitle language

selected at DVD initial settings does not exist on the disc, it will not be accessible.

• Subtitles appear only when available on disc.

•“OFF” is selected at the changing subtitle

language. Select “ON” at the “Subtitle Languages” section (p. 36) to display the subtitles.

• Alternative language cannot be selected with discs which do not contain more than one language.

• For some discs, alternative language cannot be selected with the AUDIO or SUB TITLE button. Try selecting it from the DVD MAIN MENU if available.

• This function is dependent on software availability. Even if disc has multiple angles, they may be recorded for specific scenes only (ANGLE indicator on DECK lights up). (p. 37)

Correction

• Make sure TV is set to output of DECK.

• Check connections between DECK,

external antenna, and TV.

• Set VCR/TV selector to “TV.” (p. 21)

• Make sure proper signal source is selected.

• Insert the cassette with window side up; record

tab facing you.

• Make sure cassette record tab is intact. (p. 6)

• To enable Quick play mechanism, the cylinder will

rotate for about 3 minutes. This reduces response time from Stop to Play mode.

• First, unplug DECK. Then, prepare a rigid wire (e.g. an extended paper clip) and, applying moderate force, insert it straight into the hole at the base of the tray. The tray will eject a little. Now, pull the tray all the way out and remove the disc. (p. 9)

Information

For Your

If you cannot resolve the problem, please call the Customer Call Center for product assistance at 1-800-211-PANA (7262). To locate an authorized servicenter, please call toll free 1-800-211-PANA (7262). or send e-mail to : consumerproducts@panasonic.com

D4743-4743S P36-60 (030318 C-lot).p65 2003/03/18, 15:2853

Limited Warranty

PANASONIC CONSUMER ELECTRONICS COMPANY, DIVISION OF MATSUSHITA ELECTRIC CORPORATION OF AMERICA One Panasonic Way Secaucus, New Jersey 07094

PANASONIC SALES COMPANY, DIVISION OF MATSUSHITA ELECTRIC OF PUERTO RICO, INC., AVE. 65 de Infantería, Km. 9.5 San Gabriel Industrial Park Carolina, Puerto Rico 00985

Panasonic DVD/VCR Deck Limited Warranty

Limited Warranty Coverage

If your product does not work properly because of a defect in materials or workmanship, Panasonic Consumer Electronics Company or Panasonic Sales Company (collectively referred to as “the warrantor”) will, for the length of the period indicated on the chart below, which starts with the date of original purchase (“Limited Warranty period”), at its option either (a) repair your product with new or refurbished parts, or (b) replace it with a new or a refurbished product. The decision to repair or replace will be made by the warrantor.

Product or Part Name

DVD/VCR Deck Rechargeable Batteries

(in exchange for defective item)

During the “Labor” Limited Warranty period there will be no charge for labor. During the “Parts” warranty period, there will be no charge for parts. You must mail-in your product during the warranty period. If non-rechargeable batteries are included, they are not warranted. This Limited Warranty only applies to products purchased and serviced in the United States or Puerto Rico. This Limited Warranty is extended only to the original purchaser and only covers product purchased as new. A purchase receipt or other proof of original purchase date is required for Limited Warranty service.

Parts

One (1) Year

Ten (10) Days

Labor

Ninety (90) Days

Not Applicable

Mail-In Service

For assistance in the continental U.S.A. in obtaining repairs please ship the product to:

For assistance in Puerto Rico call Panasonic Sales Company (787)-750-4300 or fax (787)-768-2910. When shipping the unit carefully pack and send it prepaid, adequately insured and preferably in the original

carton. Include a letter detailing the complaint and provide a day time phone number where you can be reached.

IF REPAIR IS NEEDED DURING THE LIMITED WARRANTY PERIOD THE PURCHASER WILL BE REQUIRED TO FURNISH A SALES RECEIPT/PROOF OF PURCHASE INDICATING DATE OF PURCHASE, AMOUNT PAID AND PLACE OF PURCHSE. CUSTOMER WILL BE CHARGED FOR THE REPAIR OF ANY UNIT RECEIVED WITHOUT SUCH PROOF OF PURCHASE.

D4743-4743S P36-60 (030610 C-lot).p65 2003/06/10, 18:4854

Panasonic Services Company Customer Servicenter Suite B 4900 George McVay Drive McAllen, TX 78503

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : consumerproducts@panasonic.com

Limited Warranty Limits And Exclusions

This Limited Warranty ONLY COVERS failures due to defects in materials or workmanship, and DOES NOT COVER normal wear and tear or cosmetic damage. The Limited Warranty ALSO DOES NOT COVER damages which occurred in shipment, or failures which are caused by products not supplied by the warrantor, or failures which result from accidents, misuse, abuse, neglect, mishandling, misapplication, alteration, faulty installation, set-up adjustments, misadjustment of consumer controls, improper maintenance, power line surge, lightning damage, modification, or commercial use (such as hotel, office, restaurant, or other business), rental use of the product, or service by anyone other than a Factory Servicenter or other Authorized Servicer, or damage that is attributable to acts of God.

THERE ARE NO EXPRESS WARRANTIES EXCEPT AS LISTED UNDER “LIMITED WARRANTY COVERAGE”. THE WARRANTOR IS NOT LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM THE USE OF THIS PRODUCT, OR ARISING OUT OF ANY BREACH OF THIS WARRANTY. (As examples, this excludes damages for lost time, cost of having

someone remove or re-install an installed unit if applicable, travel to and from the servicer, loss of or damage to media or images, data or other recorded content. The items listed are not exclusive, but are for illustration only.)

ALL EXPRESS AND IMPLIED WARRANTIES, INCLUDING THE WARRANTY OF MERCHANTABILITY, ARE LIMITED TO THE PERIOD OF THE LIMITED WARRANTY.

Some states do not allow the exclusion or limitation of incidental or consequential damages, or limitations on how long an implied Limited Warranty lasts, so the exclusions may not apply to you.

This Limited Warranty gives you specific legal rights and you may also have other rights which vary from state to state. If a problem with this product develops during or after the Limited Warranty period, you may contact your dealer or Servicenter. If the problem is not handled to your satisfaction, then write to the warrantor’s Consumer Affairs Department at the addresses listed for the warrantor.

PARTS AND SERVICE, WHICH ARE NOT COVERED BY THIS LIMITED WARRANTY, ARE YOUR RESPONSIBILITY.

Customer Services Directory

For Product Information, Operating Assistance, Literature Request, Dealer Locations, and

Customer Services DirectoryCustomer Services Directory

Customer Service inquiries please visit Web Site:

http://www.panasonic.com

You can purchase parts, accessories, locate your nearest servicenter and more by visiting our Web Site

or E-mail us via web:

http://www.panasonic.com/consumer_electronics/support/customerfeedback.asp

Contact: 1-800-211-PANA (7262), Monday-Friday 9 am-9 pm; Saturday-Sunday 10 am-7 pm, EST.

For hearing or speech impaired TTY users, TTY : 1-877-833-8855

Accessory Purchases

1-800-332-5368 (Customer Orders Only) 1-800-237-9080 (Fax Only)

(Monday-Friday 9 am-8 pm, EST.) Panasonic Services Company 20421 84th Avenue South, Kent, WA 98032 (Accepts Visa, MasterCard, Discover Card, American Express, and Personal Check)

http://www.pasc.panasonic.com or email to parts@panasonic.com

For hearing or speech impaired TTY users, TTY : 1-866-605-1277

Service in Puerto Rico

Matsushita Electric of Puerto Rico, Inc. Panasonic Sales Company/ Factory Servicenter:

Ave. 65 de Infantería, Km. 9.5, San Gabriel Industrial Park, Carolina, Puerto Rico 00985

Phone (787)750-4300 Fax (787)768-2910

As of May 2003

D4743-4743S P36-60 (030610 C-lot).p65 2003/06/10, 18:4855

Information

For Your

Spanish Quick Use Guide/ Guía para rápida consulta

AUTO CLOCK SET IS I NCOM

PLETE

PLEASE SET CLOCK BY PRESSING

ACT I ON KEY

6 / 8/ 20 03

SUN 2 : 20P

DST :

SETT I NG

: CH

AUTO CLOCK SET

COMPLETED

DST :

6 / 8 / 2003 SUN 2: 2 0 PM

SET COMPLETE

- - - - - - - - -- - - - - - - -- - - - - -

SET CLOCK

DST : O

SELE CT MONTH

1 / /

SELECT : SET :SET EXIT

: ACT I ON

- - - - - - - - -- - - - - - - -- - - - - -

SET CLOCK

CONEXIONES/CONFIGURACION INICIAL (READY TO PLAY)

Para ajustar el idioma, canal yPara ajustar el idioma, canal y

Realice la conexión de la antena o TV por cable antes de enchufar el cable de CA.

El DVD/VCR iniciará automáticamente la fijación de los canales y del reloj al enchufar el cable de CA.

CONEXIONES

Para Ant/Cable

Conecte el cable de la antena al terminal IN

FROM ANT del DVD/VCR. Conecte el terminal OUT TO TV del DVD/VCR

a la entrada de la antena VHF/UHF del TV con

➛➛

DVD/VCR

➛

➛➛

➛

➛➛

Televisor

el cable RF incluido.

Para Sistema Digital de Satelite (DSS)/ Convertidor de cable

Conecte la salida de convertidor de cable

al terminal IN FROM ANT. Conecte el terminal OUT TO TV del DVD/VCR

a la entrada de la antena VHF/UHF del TV con el cable RF incluido.

CONFIGURACION INICIAL

Encienda el TV y cambie al canal 3.

Enchufe el cable de CA.

El DVD/VCR se encenderá e iniciará las fijaciones de los canales y del reloj.

• Si no aparece la pantalla de abajo, compruebe la conexión del DVD/VCR-TV y si el canal del TV está a 3, intennte cambiando al canal 4.

• Para cambiar el canal de salida del DVD/VCR, consulte las instrucciones de “Canal de salida del VCR” (informaciones en inglés página 19).

Enchufe el cable de CA.

Televisor

VHF/UHF

Las fijaciones se realizan automáticamente.

Cuando termina las fijaciones, aparecerá la siguiente pantalla.

Si aparece en la pantalla “AUTO CLOCK SET IS INCOMPLETE (FIJACION AUTOMATICA DEL RELOJ ES INCOMPLETO)”, Ajuste el reloj como se describe a continuación.

DVD/VCR

VHF/UHF

➛➛

➛ DVD/VCR

➛➛

DVD/VCR

Terminal OUT TO TV

Terminal IN FROM ANT.

Entrada (IN) desde ANT./CABLE

➛➛

➛ TV

➛➛

Estuche convertidor de TV por cable

Entrada (IN) desde ANT./CABLE

CH AUTO SET PROCEEDING

CANCEL : STOP

AUTO CLOCK SET

PROCEEDING

CANCEL : STOP

Al inicio, el idioma de la pantalla está fijado a inglés. Para cambiar el idioma, seleccione la pantalla MENU (informaciones en inglés página 18).

Si está usanndo un convertidor de TV por cable y en su area hay un canal de Public Broadcast Station (PBS), ajuste su convertidor al canal PBS de su area. Si está usando un receptor DSS, este debe estar apagado.

Nota

• Los botones de funciones no funcionan durante la configuración inicial.

• Para retirar un cassette durante el ajuste automático, presione EJECT en el control remoto o STOP dos veces en el aparato. En este caso, los ajustes de los canales y la hora se deben hacer manualmente. Para los ajustes seleccione la pantalla MENU (informaciones en inglés página 18).

• Dependiendo de las condiciones, el ajuste automático puede durar más de 30 minutos. En ese caso, presione STOP para detener el ajuste automático y realice los ajustes manualmente en la pantalla MENU.

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : consumerproducts@panasonic.com

D4743-4743S P36-60 (030318 C-lot).p65 2003/03/18, 15:2856

Por ayuda llame al 1-800-211-PANA(7262) o envie e-mail a : consumerproducts@panasonic.com

AJUSTE MANUAL DEL RELOJ

Si la fijación ha sido incompleta.

Presione la tecla ACTION en el control remoto

para visualizar la pantalla del menú SET CLOCK.

Presione para seleccionar el mes y SET

para ajustar. De la misma forma, seleccione y ajuste la fecha, año, hora y DST (hora de verano).

Presione dos veces la tecla ACTION para

poner el RELOJ en marcha y salir.

PRECAUCIÓN

Al usar cables coaxiales RF del tipo “tuerca”, apriételos solamente con los dedos. Un apriete excesivo puede dañar los terminales.

Operaciones básicas para la reproducción

Inserte un cassette,

• La alimentación del DECK se activa. En la Pantalla de Visualización Multi Función se ilumina “VCR”.

Presione PLAY para reproducir el cassette.

• Si el cassette no tiene la lengüeta de prevención de grabación (página 6), se inicia la reproducción automáticamente.

Detalles especiales durante la grabación

Presione FF/SLOW+ o REW/SLOW- para

búsqueda de escenas hacia delante/ hacia atrás. Presione PLAY para liberar. Durante la búsqueda, cada vez que presione FF o REW se cambia la velocidad como sigue: [SLP] aprox. 21X [LP] aprox. 9X [SP] aprox. 7X

↔↔

↔ aprox. 9X

↔↔ ↔↔

↔ aprox. 7X

↔↔ ↔↔

↔ aprox. 3X

↔↔

Si la imágen se interrumpe con la velocidad de 21X, 9X o 7X, cambie la velocidad a 9X, 7X o 3X. Presione PAUSE/STILL para imagen Fija (Congelada).

Presione PLAY para liberar. Presione PAUSE/STILL en el modo de

imagen fija para imágenes cuadro a cuadro.

Presione PLAY para liberar. Presione FF/SLOW+ o REW/SLOW- en el

modo de imagen fija para cambiar la velocidad de las imágenes a cámara lenta.

Presione STOP para detener el cassette.

Presione REW/SLOW- o FF/SLOW+ en el

modo de parada para rebobinado/avance rápido del cassette. Presione EJECT en el control remoto, o STOP/EJECT en el DECK para expulsar el cassette.

Operaciones básicas para la grabación

Inserte el cassette con lengüeta de

protección de grabación (página 6).

Presione CH / , o las teclas de números

para seleccionar el canal.

Presione SPEED para seleccionar la

velocidad de grabación (página 6).

• SP = Reproducción estándar,

• LP = Larga duración,

• SLP = Superlarga duración.

Presione REC para comenzar a grabar.

• Para eliminar escenas indeseadas, presione PAUSE/STILL para hacer una pausa, y al presionar nuevamente continua la grabación.

• No podrá ver otro canal durante la grabación.

Presione STOP para detener la grabación.

Programación fácil para la grabación con temporizador

Presione PROG

para visualizar la pantalla de Programacion.

N I C I

FECHA

7 SAB

SLP

HOY

ELEGIR FECHA DE I N I C I O

ELEGIR FIJAR TERMINAR

PARADA

--:-- --:-- --

:SET

PROG

Orden para elegir

Ejemplo

Fecha de hoy

2) Para ajustar los ítems que quedan, presione para seleccionar y presione SET para ajustar los tiempos de INICIO/

PARADA, CANAL, o entrada de LINEA (página

35), y velocidad del cassette (SP, LP, SLP). Presione PROG para finalizar PROGRAM.

I N I C

2 : 00 P 3 : 20 P

-- -- : --

-- : --

CANC

ELAR: ADD / DLT

ELEGIR 1- 8 :

: SET

ENTRAR SAL I R

: PROG

PARADA CA VEL

-- : -- --

Grabación de un toque

Presione REC repetidamente para ajustar la

hora de grabación (30 min - 4 horas).

• La videograbadora termina la grabación

a una hora programada.

Grabación normal

1) Para ajustar la FECHA de

grabación, presione

para seleccionar: 1-31 = una vez, o DIARIO = a la misma hora de lunes a viernes, o SEMANA = a la misma hora cada semana y presione SET para ajustar.

/ Orden para elegir

SEMANAL

Presione

02 SLP

para seleccionar un número

que no está usando para ingresar mas programas y

presione SET

(

SAB

SEMANAL

(

LUN

)

para ajustar. Luego repita el paso 2. O

Presione nuevamente PROG para salir.

0:30 1:00

1:302:003:004:00

)

68 9

SEMANAL

(

DOM

)

DIARIO

Guía para rápida

consulta

D4743-4743S P36-60 (030318 C-lot).p65 2003/03/18, 15:2857

Spanish Quick Use Guide/ Guía para rápida consulta

Operaciones básicas del DVD

Presione

aparato.

Presione

1) Presione

2) Ponga un disco en la bandeja de disco.

• Sujete el disco sin tocar ninguna de sus superficies, póngalo con el lado donde esté impreso el título hacia arriba, alinéelo con las guías y póngalo en su posición apropiada. Disco de 3” (8 cm) / Disco de 5” (12 cm)

Presione

La bandeja del disco se cierra automáticamente.

• Si está usando un DVD interactivo (Interactive DVD) o un Vídeo CD con contol de reproducción (playback control) y aparece un menú de títulos (TITLE MENU) en la pantalla, siga al paso 5.

Presione o las teclas numéricas para

seleccionar el artículo deseado.

Presione Si usa las teclas numéricas, la reproducción comienza automáticamente.

Presione

■ Para buscar una escena particular Búsqueda hacia adelante

Presione

Búsqueda hacia atrás

Presione (Para liberar, presione

■ Para saltar un capítulo o una pista Salto hacia adelante

Presione

Un capítulo (DVD) o una pista (Vídeo CD/CD) se salta cada ves que se oprime la tecla.

Salto hacia atrás

Presione l

■■

■ Para ver una imagen fija

■■

Presione (Para liberar, presione

■ Para ver imágenes cuadro a cuadro (DVD/Vídeo CD) Presione

La imagen avanza un cuadro cada vez que presiona la tecla. (Para volver a la reproducción normal, presione

■ Para ver en cámara lenta (DVD/Vídeo CD) Presione

de imagen fija. (Para liberar, presione

POWER

DVD

SET o PLAY

OPEN/CLOSE

FF/SLOW+

REW/SLOW-

SKIP

PAUSE/STILL

FF/SLOW+

en el control remoto o el

para seleccionar el modo DVD.

OPEN/CLOSE

PLAY

para iniciar la reproducción.

STOP

para parar la reproducción.

en el modo de reproducción.

l en el modo de reproducción.

SKIP

en el modo de reproducción.

para la reproducción.

para expulsar el disco.

en el modo de reproducción.

PLAY

)

durante la reproducción.

PLAY

)

en el modo de imagen fija.

REW/SLOW-

PLAY

)

PLAY

)

en el modo

POWER

SELECT

SET

STOP

REW/

SLOW-

FF/

SLOW+

PAUSE/

STILL

OPEN/ CLOSE

NUMBER keys

DVD PLAY

SKIP SKIP

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : consumerproducts@panasonic.com

D4743-4743S P36-60 (030318 C-lot).p65 2003/03/18, 15:2858

Por ayuda llame al 1-800-211-PANA(7262) o envie e-mail a : consumerproducts@panasonic.com

Funcionnamiento del DVD utilizando visualizaciones en pantalla

Cuando se presiona DISPLAY, la visualización en pantalla muestra la información del disco (título / capítulo / número de lista, tiempo transcurrido de reproducción, audio / idioma del subtítulo, y ángulo) e información (repetir la reproducción, modo reproducción, Karaoke vocal encendido / apagado, etc.).

Presione

o parada para visualizar las visualizaciones en pantalla.

• Cada vez que se presione

visualización en pantalla cambia como se muestra a continuación.

Presione (o ) para seleccionar el ítem

deseado.

Presione Presione para seleccionar el ajuste

deseado.

Presione Para volver a la pantalla normal, Presione repetidamente

DISPLAY

Información seleccionada del disco

Información seleccionada del DECK

en el modo reproducción

DISPLAY

➡

,la

Pantalla normal

SET

para ajustar.

SET

para ajustar.

CLEAR o DISPLAY

T ITULO : 12 DVD

CAPI TULO:11 00:12:34

T ITULO : 12 DVD CAPI TULO: 24 00: 12 : 34

ADD/DLT SELECT

SET

DISPLAY

ELEGI R: FI JAR : SET SIGUI ENTE: DI SPLAY

PI STA : 12 VIDEO CD

PBC : I NACTIVO 00 :12 : 34

FI JAR : SET SIGUI ENTE: DI SPLAY

D4743-4743S P36-60 (030318 C-lot).p65 2003/03/18, 15:2859

PI STA : 17 VIDEO CD PBC : I NACTIVO 00 :12 : 34

FI JAR : SET SIGUI ENTE: DI SPLAY

Guía para rápida

consulta

Spanish Quick Use Guide/ Guía para rápida consulta

Utilización de un menú de títulos [DVD solamente]

Algunos discos con películas, vienen con dos o más títulos. Por ejemplo, si el disco tiene un menú de títulos grabados, el botón TITLE podrá utilizarse para seleccionar el título de la película.

Presione

Ahora se visualiza una lista de los títulos del disco.

TITLE

T I TLE MENU

Cas t l es

Dogs

Love

Dogs

of the world

durante la reproducción.

Presione o las teclas de números para

i r

seleccionar el título

deseado.

Presione

SET

para elegir.

Utilización de un menú de DVD [DVD solamente]

Algunos discos DVD ofrecen un menú especial. Este menú incluye guías para contenidos únicos, audio, subtitulos, idiomas, etc. Aunque los contenidos y las operaciones se cambian, los siguientes son unos pasos básicos para el uso del menú.

Presione

El menú de DVD introducido en el disco se visualiza ahora.

DVD MENU

1 . SUBT I TLE 2 . AUD

3 . ANGLE

durante la reproducción.

Presione o las teclas de números para

seleccionar el ítem deseado.

Presione

SET

para elegir.

Ampliación de la imagen [DVD solamente]

Durante la reproducción de un DVD, puede ampliar partes específicas de una imagen y seleccionar la relación de zoom usando el botón ZOOM.

Presione

tamaño de la imagen como se indica a continuación:

■ Use los botones , , y para desplazar

ZOOM

repetidamente para cambiar el

la posición hacia arriba, hacia abajo, hacia la izquierda o hacia la derecha.

2da

3da

Funcionamiento de la ejecución de MP3/WMA/JPEG

Puede utilizar esta unidad para reproducir audio de formato MP3/WMA/JPEG, grabado para uso personal con una computadora, etc., en un CD-ROM o CD-RW. La ejecución no podrá realizarse en algunos casos, debido a las condiciones de la grabación.

Presione

coloque un disco MP3/WMA/JPEG en la bandeja

POWER

en el control remoto o DECK.

OPEN/CLOSE

y a continuacion

de discos.

Presione

Se visualizará el MENU MP3/WMA/JPEG y la

ejecución se iniciará automáticamente. (Se

OPEN/CLOSE

para cerrarla.

visualizará el directorio del CD.)

Estado de la función

Area de las carpetas

(La carpeta visualizada actualmente se volverá verde)

:Archivo MP3 :Archivo WMA :Archivo JPEG

:Carpeta :Carpeta principal

REPROD

ROOT . .

END_W

TECHNO

POPS

NOCTURNE

AZZ

NORN

MODE DE REPRODUCCION: NORMAL

MODO DE REPRODUCCIÓN

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : consumerproducts@panasonic.com

Por ayuda llame al 1-800-211-PANA(7262) o envie e-mail a : consumerproducts@panasonic.com

DD_

ALTZ

CUB I C

00 : 00 :

(El archivo/ la carpeta se visualiza con un cursor.)

Contador Carpeta

principal Area de

archivos

■ Ejecución MP3/WMA/JPEG (Durante el modo STOP)

Presione para seleccionar un archivo MP3/WMA

) o un archivo JPEG ( ), y presione

(

PLAY

• MP3/WMA

Búsqueda hacia adelante/hacia atrás

➡Presione

Salto de pista hacia adelante/hacia atrás

➡Presione

• JPEG

Búsqueda siguiente/anterior

➡Presione

Inicie la muestra-diapositiva

➡Presione

Ampliar una imagen ➡ Presione Girar una imagen ➡ Presione

Presione

■ Seleccione MODO DE REPRODUCCION

(Durante el modo STOP)

Presione para mover el cursor a MODO DE REPRODUCCION, y Presione

MODO DE REPRODUCCIÓN deseado.

[MODO DE REPRODUCCIÓN] NORMAL: Todos los archivos se reproducen sólo una vez REPETICION DE UNA MUSIC:

El archivo seleccionado se reproduce repetidamente. REPETICION DE UN ARCHIVO: Los archivos que se encuentran en la carpeta seleccionada se reproducen repetidamente. REPETICION DEL DISCO: Todos los archivos se reproducen repetidamente.

Presione

PRINCIPAL.

FF/SLOW+

SKIP

STOP

ACTION

REW/SLOW-

| o |

SKIP

| o |

FF/SLOW+

para detener la operacion descrita arriba.

para regresar al DVD MENU

SKIP

REW/SLOW-

ANGLE

durante la ejecución.

ZOOM

para seleccionar el

durante la ejecución.

SET

D4743-4743S P36-60 (030318 C-lot).p65 2003/03/18, 15:2860

Fijaciones iniciales

Presione DVD para seleccionar el modo DVD.

Presione ACTION en el modo de parada para

visualizar MENU.

Presione para seleccionar el artículo deseado.

Presione

IDIOMAS DEL DISCO

Todos los idiomas ofrecidos en el disco pueden ser ajustados. Si el idioma ajustado no es ofrecido en el disco, se seleccionará el idioma original del disco.

SALIDA DE AUDIO

Puede usted ajustar la salida audio procedente del terminal de salida audio digital.

DETENER RASTREO

Para seleccionar “CAMPO” o “CUADRO fijo” para prevenir inestabilidad o para permitir ver textos pequeños o patrones finos claramente en el modo de imagen fija.

TV PREFERENCIA

Para seleccionar cuando el material del vídeo es para pantalla ancha y se quiere reproducir en el estilo Pan&Scan, en el estilo Letterbox o en el estilo 16 : 9 en la pantalla.

Presione para seleccionar el artículo deseado.

Presione Volver a visualizar el menú de DVD para

continuar el ajuste. Presione ajuste o, para salir, presione

SET

ACTION

y pase al paso 3 para ajustar otro

ACTION

tres veces.

Cambio del idioma de subtítulos [DVD solamente]

EI idioma de los subtítulos seleccionado al hacer las fijaciones iniciales se puede cambiar por otro idioma diferente, si éste se encuentra disponible.

ELEGIR : ACTIVO / INACTIVO : TERMINAR : SUB TITLE

Presione

la reproducción. Cuando no haya subtítulos grabados, se visualizará “-” en lugar del número de idioma.

Presione para seleccionar el idioma deseado. Presione para seleccionar “ACTIVO” o “INACTIVO.”

SUBTITLE

durante

Selección de vocal para los discos de Karaoke [DVD/Vídeo CD]

Presione

para visualizar la pantalla AUDIO.

ELEG I R: TERMI

• DVD Karaoke (1 vocal) VOCAL ON VOCAL OFF

• DVD Karaoke (2 vocals) VOCAL V1 VOCAL V2 VOCAL V1+V2 VOCAL OFF

• Video CD LR L R

NAR : AUDIO

AUDIO

durante la reproducción

Presione (o ) para seleccionar el ajuste deseado. Presione (o ) para ajustar. (DVD solamente)

Selección de IDIOMAS DEL DISCO [DVD solamente]

Seleccione “AUDIO”

(Fijación de fábrica : inglés)

Inglés / Español / Francés / Japonesa : Original : Se seleccionará el idioma

OTRO

Seleccione “SUBTITULO”

AUTO : Se seleccionará el mismo que fue

• Si el idioma seleccionado en la preparación de “AU DIO ” se utiliza durante la reproducción, los subtítulos no aparecerán.

• Si se utiliza otro idioma durante la reproducción, los subtítulos aparecerán en el idioma seleccionado en la preparación de “AUDIO”

Inglés / Español / Francés / Japonesa : OTRO

original de cada disco.

✱✱✱✱

:Se puede seleccionar el otro

idioma.

seleccionado en la preparación de “AUDIO”. (Fijación de fábrica)

✱✱✱✱

: Se puede seleccionar el otro

idioma.

Seleccione “MENU”

(Fijación de fábrica : inglés)

Inglés / Español / Francés / Japonesa : OTRO

✱✱✱✱

: Se puede seleccionar el otro

idioma.

Visión desde otro ángulo [DVD solamente]

Algunos discos DVD tienen escenas que han sido filmadas simultáneamente desde un número de ángulos diferentes. Con estos discos, la misma escena podrá verse desde cada uno de estos ángulos diferentes utilizando el botón ANGLE.

ANGULO

ELEGIR :

ANGULO

ELEGIR :

: 1

: 2

Presione

reproducción para visualizar la selección del ángulo.

Presione para seleccionar el ángulo deseado.

ANGLE

durante la

Cambio del idioma de la pista de sonido [DVD solamente]

EI idioma de la pista de sonido seleccionado al hacer las fijaciones iniciales se puede cambiar por otro idioma diferente, si éste se encuentra disponible.

ELEG I R: TERMI

NAR : AUDIO

ELEG I R: TERMI

NAR : AUDIO

Presione

durante la reproducción para visualizar SONIDO en la pantalla.

Presione para seleccionar idioma.

AUDIO

Guía para rápida

consulta

D4743-4743S P36-60 (030318 C-lot).p65 2003/03/18, 15:2861

Index

DECK & VCR

A ACTION button ................................. 8, 18

Accessories ............................................ 4

ADD/DELETE button

(Add or Delete a Channel) .................. 8, 19

Audio Broadcast types

(Stereo/SAP/Mono) ............................ 26

Audio Mode (Playback, Recording) .... 27

Auto Operation Functions .................... 31

Auto Shut-Off ........................................ 33

B Batteries ................................................. 4

C Channel (“SET UP CHANNEL”).......... 18

Channel Up/Down,

Tracking/V-Lock Button ......................6, 8

Clock (“SET CLOCK”) .......................... 18

Commercial Skip ................................. 31

Connections................................. 12 ~ 15

Copy Your Tapes (Dubbing) ............... 35

COUNTER RESET button ............... 8, 32

Customer Services Directory............... 55

D DISPLAY button ............................... 8, 11

DST (Daylight Saving Time) ................ 19

E EJECT button ................................... 8, 20

ENTER button

(For tuning TV Channel) ................ 8, 28

F FAST FORWARD/SEARCH button .. 8, 20

H Head Cleaning ...................................... 6

I Index Search ........................................ 30

Indicator (Multi Function Display) ....... 11

Initial Setup (Ready to Play) ......... 16, 17

INPUT button ................................... 8, 35

L Limited Warranty ........................... 54, 55

Location of Controls

(Remote, DECK) .......................... 8 ~ 10

MMulti-Brand Control ....................... 28, 29

O On-Screen Displays (VCR) .................. 11

One Touch Recording ......................... 21

P PAUSE/STILL button (Still Picture) .. 8, 20

PLAY button (Playback a Tape) ...... 8, 20

POWER button ....................................... 8

PROG button (PROGRAM) .............. 8, 24

Program Clear, Review, Replace ....... 25

Program End Search ........................... 30

Q Quality Picture ........................................ 6

R REC button (Record on a Tape) ..... 8, 21

Record Tab ............................................ 6

Remote Sensor ...................................... 9

Remote Warning .................................. 34

Repeat Play ......................................... 32

Reset All Memory Functions ................. 9

REWIND/SEARCH button ............... 8, 20

S SAP/Hi-Fi ............................................. 27

(Index and Program End Search) ..... 30

SLOW+/SLOW

(Slow Motion Picture) ........................ 8, 20

Spanish Quick Use Guide ...........56 ~ 61

Specifications......................................... 7

SPEED button .................................. 8, 21

Still (Freeze) Picture ............................ 20

STOP button ..................................... 8, 20

T Tape Position, Tape Status ................. 34

Timer Recording .................................. 24

Trouble Shooting ........................... 52, 53

TV mode button ................................ 8, 28

V VCR Lock ............................................. 33

VCR mode button ............................ 8, 28

VCR/TV button ................................. 8, 21

VCR/TV Selector Feature .................... 32

VOLUME +/

WWarning and Instruction Displays ....... 51

Weak Signal Display ........................... 33

Z ZERO SEARCH button .................... 8, 32

button

button (TV Volume) ... 8, 28

D4743-4743S P36-60 (030318 C-lot).p65 2003/03/18, 15:2862

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : consumerproducts@panasonic.com

DVD

A ACTION button ................................. 8, 47

ANGLE button

(Multiple Angle Viewing) ......... 8, 37, 45

AUDIO button

(Audio Soundtrack Language) ....... 8, 36

Audio Output

(For Selecting Audio Output) ............. 48

Auto-Power Off Function ..................... 23

C CLEAR button ............................ 8, 39, 46

Component Video Output .............. 10, 13

D Disc Languages................................... 47

DISPLAY button

(“On-Screen Display”).................... 8, 41

DTS ...................................................... 14

DVD Menu ........................................... 38

DVD mode button ............................ 8, 28

DVD Lock Ratings ............................... 46

F Frame by Frame Picture ...................... 23

Forward/Reverse Chapter/Track Skip... 23

Forward/Reverse Scene Search ........... 23

J JPEG ............................................ 43 ~ 45

K Karaoke

(Vocal Selection for Karaoke Discs) .... 37

L Language Code List ............................ 50

MMENU button

(To display DVD Menu) ................. 8, 38

MP3 ...................................................... 43

Multiple Angle Viewing........................ 37

O OPEN/CLOSE button ....................... 8, 22

Optical Digital Audio Output .......... 10, 15

P PLAY button (Play a Disc) ............... 8, 22

Program Play (For Video CD/ CD) ...... 39

PROGRESSIVE button .......................... 9

Progressive Scan................................. 10

R Random Play (For Video CD/ CD) ...... 40

Repeat Play ......................................... 42

Resume Function................................. 23

RETURN button ............................... 8, 22

Rotation................................................ 45

S SEARCH button

(Forward/Reverse Scene Search) .. 8, 23 SKIP (Forward/Reverse Chapter/Track) .. 8, 23

Slide-show ........................................... 44

SLOW+/SLOW

(Slow Motion Picture)....................... 8, 23

STILL button

(Still Picture or Pause) ................... 8, 23

Still Mode

(For selecting “FIELD” or “FRAME”)...... 49

STOP button ..................................... 8, 22

SUB TITLE button (For selecting Subtitle Language) .. 8, 36

S-Video Out.................................... 10, 13

T TITLE button (Title Menu) ................ 8, 38

TV Mode

(For selecting the screen display style) ...... 49

V Video CD ............................................. 23

VOLUME ADJUST button ................ 8, 40

V.S.S. (Virtual Surround Sound) ..... 8, 23

WWMA ..................................................... 43

Z ZOOM button (Picture Zoom) ..... 8, 37, 45

l or l button

button

Information

For Your

D4743-4743S P36-60 (030318 C-lot).p65 2003/03/18, 15:2863

Panasonic Consumer Electronics Company, Division of Matsushita Electric Corporation of America

One Panasonic Way Secaucus, New Jersey 07094

Panasonic Sales Company (“PSC”), Division of Matsushita Electric of Puerto Rico, Inc.

Ave. 65 de Infantería. Km. 9.5 San Gabriel Industrial Park, Carolina, Puerto Rico 00985

D4743-4743S P36-60 (030610 C-lot).p65 2003/06/10, 18:4864

Printed in Indonesia

LSQT0674C

S0103-2063

Panasonic PVD4743S DoubleFeature OmniVision VHS, PVD4743 DoubleFeature OmniVision VHS User Manual [es]

Specifications and Main Features

Frequently Asked Questions

User Manual