Panasonic PV-D4742, PV-D4752 User Manual

Download

Page 1

DVD/VCR DECK

Operating Instructions

(Connection)

Initial Setup

Model No.

PV-D4742/PV-D4752

Operation

Basic

Operation

VCR

Operation

DVD

Connections and Initial Setup Procedures are on pages 12 to 17.

Information

(PV-D4752 only)

As an ENERGY STAR Partner, Matsushita Electric Corporation of America has determined that this product or product model meets the

NERGY STAR guidelines for energy efficiency.

Please read these instructions carefully before attempting to connect, operate or adjust this product. Please save this manual. Spanish Quick Use Guide is included. (Guía para rápida consulta en español está incluida.)

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : consumerproducts@panasonic.com

LSQT0580A

For Your

Page 2

Important Safeguards and Precautions

FOR YOUR SAFETY, READ AND RETAIN ALL SAFETY AND OPERATING INSTRUCTIONS. HEED ALL WARNINGS IN THE MANUAL AND ON THE UNIT

INSTALLATION

1 POWER SOURCE CAUTION

Operate only from a power source indicated on the unit or in this manual. If necessary, have your Electric Utility Service Company or Video Products Dealer verify the power source in your home.

2 POLARIZED OR GROUNDING PLUG

As a safety feature, this product comes with either a polarized power cord plug (one blade is wider

than the other), or a three-wire grounding type plug. POLARIZED PLUG CAUTION: This plug will only fit into an outlet one way. If you cannot

fully insert the plug, try reversing it. If it still will not fit, have an electrician install the proper wall outlet. Do not defeat the safety feature by tampering with the plug.

GROUNDING PLUG CAUTION: This plug will only fit into a three-hole grounding

outlet. If necessary, have an electrician install the proper outlet. Do not defeat the safety feature by tampering with the plug.

3 POWER CORD

Make sure power cords are routed so that they

are not likely to have anything rest on them, roll

over them, or be in the way of walking traffic.

If an extension cord is used, make sure it also

has either a polarized or grounded plug and that

the cords can be securely connected.

Frayed cords, damaged plugs, and damaged or

cracked wire insulation are hazardous and should

be replaced by a qualified service technician.

Overloaded outlets and extension cords are fire

hazards and should be avoided.

4 DO NOT BLOCK VENTILATION HOLES

Ventilation openings in the cabinet release heat

generated during operation. If they are blocked,

heat build-up inside the unit can cause failures that

may result in a fire hazard or heat damage to

cassettes or discs.

For protection, follow these rules:

a. Never cover ventilation slots or the unit while in

use, or operate the unit when placed on a bed, sofa, rug, or other soft surface.

b. Avoid built-in installation, such as a book case

or rack, unless proper ventilation is provided.

5 PLACEMENT: AVOID EXTREMELY HOT LOCATIONS

OR SUDDEN TEMPERATURE CHANGES

Do not place the unit over or near heater or

radiator, in direct sunlight, inside closed vehicles,

in high temperature [over 104°F (40°C)], or in over

75% humidity. If the unit is suddenly moved from

a cold place to a warm one, moisture may

condense in the unit and on the tape causing

damage. Never subject the unit to vibration,

impact, or place it so that the surface is titled as

internal parts may be seriously damaged.

6 TO AVOID PERSONAL INJURY

• Do not place unsecured equipment on a sloping surface.

• Do not place this unit on any support that is not firm, level, and adequately strong. The unit could fall causing serious injury to a child or adult and damage to the unit.

• An appliance and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the appliance and cart combination to overturn.

• Carefully follow all operating instructions and use the manufacturer's recommended accessories when operating this unit or connecting it to any other equipment.

1 SAFE ANTENNA AND CABLE CONNECTION

If an outside antenna or cable system is connected to the equipment, be sure the antenna or cable system is grounded so as to provide some protection against built up static charges and voltage surges. Section 810 of the National Electrical Code, ANSI/NFPA 70 (in Canada, part 1 of the Canadian Electrical Code) provides information with respect to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna discharge unit, connection to grounding electrodes and requirements for the grounding electrode.

KEEP ANTENNA CLEAR OF HIGH VOLTAGE POWER LINES OR CIRCUITS

An outside antenna system should be located well away from power lines, electric light or power circuits and where it will never come into contact with these power sources if it should happen to fall. When installing an outside antenna, extreme care should be taken to avoid touching power lines, circuits or other power sources as this could be fatal. Because of the hazards involved, antenna installation should be left to a professional.

If the unit has been in storage or moved to a new location, refer first to the INSTALLATION section of these safeguards.

KEEP THE UNIT AWAY FROM WATER OR MOISTURE OF ANY KIND.

2 IF EQUIPMENT IS EXPOSED TO RAIN, MOISTURE, OR

STRONG IMPACT, unplug the unit and have it inspected by a

qualified service technician before use.

3 DURING AN ELECTRICAL STORM

During a lightning storm, whether indoors or outdoors, or before leaving the unit unused for extended periods of time, disconnect all equipment from the power source as well as the antenna and cable system.

4 WHEN THE UNIT IS PLUGGED IN

• Never expose the unit to rain or water. DO NOT OPERATE

• Never drop or push any object through openings in the unit.

• Avoid placing the unit directly above or below your TV set

5 USING ACCESSORIES

Use only accessories recommended by the manufacturer to avoid risk of fire, shock, or other hazards.

6 CLEANING THE UNIT

Unplug the unit. Then, use a clean, dry, chemically untreated cloth to gently remove dust or debris. DO NOT USE cleaning fluids, aerosols, or forced air that could over-spray, or seep into the unit and cause electrical shock. Any substance such as wax, adhesive tape, etc. may mar the cabinet surface. Exposure to greasy, humid, or dusty areas may adversely affect internal parts.

1 DO NOT SERVICE THIS PRODUCT YOURSELF

2 IF REPLACEMENT PARTS ARE REQUIRED

OUTDOOR ANTENNA INSTALLATION

NEC

- NATIONAL ELECTRICAL CODE

ELECTRIC SERVICE EQUIPMENT

USING THE UNIT

if liquid has been spilled into the unit. Immediately unplug the unit, and have it inspected by a service technician. Fire and shock hazards can result from electrical shorts caused by liquid contact inside.

Some internal parts carry hazardous voltages and contact can cause electric shock or fire hazard. Do not put any foreign object on the disc tray.

as this may cause electrical interference. Keep all magnets away from electronic equipment.

SERVICE

If, after carefully following the detailed operating instructions, this product does not operate properly, do not attempt to open or remove covers, or make any adjustments not described in the manual. Unplug the unit and contact a qualified service technician.

Make sure the service technician uses only parts specified by the manufacturer, or those having the same safety characteristics as the original parts. The use of unauthorized substitutes may result in fire, electric shock, or other hazards.

HAVE THE SERVICE TECHNICIAN PERFORM A SAFETY CHECK

After any service or repairs to the unit, request the service technician to conduct a thorough safety check as described in the manufacture’s service literature to ensure that the unit is in safe operating condition.

GROUND CLAMP

ANTENNA LEAD IN WIRE

ANTENNA DISCHARGE UNIT (NEC SECTION 810-20)

GROUNDING CONDUCTORS (NEC SECTION 810-21)

GROUND CLAMPS

POWER SERVICE GROUNDING ELECTRODE SYSTEM (NEC ART 250, PART H)

Page 3

Safety Precautions/Mesures de sécurité

WARNING: To prevent fire or shock hazard, do not expose this

equipment to rain or moisture.

CAUTION: To prevent electric shock, match wide blade of plug to

wide slot, fully insert.

Avertissement: Afin de prévenir tout risque d’incendie ou de chocs

électriques, ne pas exposer cet appareil à la pluie ou à une humidité excessive.

Attention: Pour éviter les chocs électriques, introduire la lame la

plus large de la fiche dans la borne correspondante de la prise et pousser jusqu’au fond.

This symbol warns the user that uninsulated voltage

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK)

NO USER-SERVICEABLE PARTS INSIDE

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL

within the unit may have sufficient magnitude to cause electric shock. Therefore, it is dangerous to make any kind of contact with any inside part of this unit.

This symbol alerts the user that important literature concerning the operation and maintenance of this unit has been included. Therefore, it should be read carefully in order to avoid any problems.

CAUTION:

UNIT IS A CLASS I LASER PRODUCT. HOWEVER THIS UNIT USES A VISIBLE LASER BEAM WHICH COULD CAUSE HAZARDOUS RADIATION EXPOSURE IF DIRECTED. BE SURE TO OPERATE THE UNIT CORRECTLY INSTRUCTED.

WHEN THIS UNIT IS PLUGGED TO THE WALL OUTLET, DO NOT PLACE YOUR EYES CLOSE TO THE OPENING OF THE DISC TRAY AND OTHER OPENINGS TO LOOK INTO THE INSIDE OF THIS UNIT.

USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.

DO NOT OPEN COVERS AND DO NOT ATTEMPT TO REPAIR YOURSELF. REFER SERVICING TO QUALIFIED PERSONNEL.

FCC NOTE:

This equipment has been tested and found to comply with part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when operated in a residential environment. If this equipment does cause interference to radio or television reception, which can be determined by turning the equipment off and on, use the equipment in another location and/or utilize an electrical outlet different from that used by the receiver. If necessary, consult the dealer or an experienced radio/TV technician for help. The user may find the booklet, “Something About Interference” available from FCC local regional offices helpful.

FCC Caution:

To assure continued compliance, (example- use only shielded interface cables when connecting to other devices.) Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.

Apparatus Claims of U.S. Patent Nos. 4,631,603, 4,577,216, and 4,819,098, licensed for limited viewing uses only.

FCC Warning: Any unauthorized changes or modifications to this equipment would void the user’s

authority to operate.

CAUTION:

LASER RADIATION WHEN OPEN DO NOT STARE INTO BEAM.

ATTENTION:

RAYONNEMENT LASER EN CAS D’OUVERTURE. NE PAS REGARDER DANS LE FAISCEAU.

(Inside of product)

Region Management Information:

This DECK is designed and manufactured to respond to the Region Management Information that is recorded on a DVD disc. If the Region number described on the DVD disc does not correspond to the Region number of this DECK, this DECK cannot play this disc.

The Region number for this DECK is 1.

Page 4

Before Using

Congratulations

on your purchase of one of the most sophisticated and reliable products on the market today. Used properly, it will bring you years of enjoyment. Please fill in the information below. The serial number is on the tag located on the back of your DECK.

• Date of Purchase

• Dealer Purchased From

• Dealer Address

• Dealer Phone No.

• Model No.

• Serial No.

Accessories

Remote Control

LSSQ0333 (PV-D4742) LSSQ0344 (PV-D4752)

Batteries 2 “AA”

RF Coaxial Cable VJAS0196

Disc formats supported by this DECK

DECK can play back discs bearing any of the following marks:

DVD

3” (8 cm) disc / 5” (12 cm) disc

Video CD

3” (8 cm) disc / 5” (12 cm) disc

Discs which cannot be played

• DVD with Region No. other than “1” or “ALL”

• DVD of PAL system • DVD-R/DVD-RAM

• DVD-ROM • CD-ROM

• CDV • CD-G

Do not try to play Photo CD.

is a registered trademark.

Disc Handling

Handling precautions

• Only hold disc by edges as shown below. Fingerprints, dirt and scratches can cause skipping and distortion.

• Do not write on label side of disc.

• Never use record cleaning sprays, benzine,

thinner, static electricity prevention liquids, or any other solvent.

• Be careful not to drop or bend disc.

To order accessories, call toll free 1-800-332-5368.

Loading the Batteries

1) Open cover.

2) Insert batteries as marked.

3) Close cover.

Battery replacement caution

• Do not mix old and new batteries.

• Do not mix alkaline with manganese

batteries.

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : consumerproducts@panasonic.com

• Do not place more than 1 disc on disc tray.

• Do not try to close disc tray when disc is not properly placed.

• Always store discs in their proper cases when not in use.

Disc tray

Disc

To clean disc surface

With a soft, damp (water only) cloth, gently wipe from the center hole to the outer edge as shown below. (Wiping in a circular pattern will scratch the surface.)

If disc is brought from a cold to a warm environment, moisture may form on the disc

Wipe away moisture with a soft, dry, lint-free cloth before using disc. (See above.)

Improper disc storage

Discs could be damaged if stored or left in areas:

• exposed to direct sunlight.

• that are humid or dusty.

• near heat (i.e. heater, radiator, etc.).

Page 5

DVD / VCR

Important Safeguards and Precautions ............................ 2, 3

Before Using ............................................................................ 4

DECK & Cassette Information ........................................... 6 , 7

Location of Controls ....................................................... 8 ~ 10

Displays (On Screen Displays and Multi Function Display) .................... 11

Connections .................................................................. 12 ~ 15

Initial Setup for Basic Connections (Ready to Play) .......... 16, 17

VCR Reset Language, Channels, Clock, VCR’s Output Channel ... 18, 19

Playback/ Record on a Tape........................................... 20, 21

DVD

Basic DVD Operation ...................................................... 22, 23

Timer Recording .............................................................. 24, 25

MTS Broadcast/ VHS Hi-Fi Stereo System .................... 26, 27

Multi-Brand Control Feature ........................................... 28, 29

Tape Operation (Search System) ....................................... 30 ~ 32

Special VCR Features ..................................................... 33, 34

Copying Your Tapes (Dubbing) ......................................................... 35

(Connection)

Initial Setup

Operation

Basic

Operation

VCR

Disc Operation ............................................................... 36 ~ 40

DVD Operation using On-Screen Displays ................. 41 ~ 42

MP3 Playback Operation....................................................... 43

DVD Lock Feature ................................................................. 44

Settings for DVD Operation .......................................... 45 ~ 47

Language Code List .............................................................. 48

DVD / VCR

Warning and Instruction Displays........................................ 49

Before Requesting Service............................................. 50, 51

Servicenter List...................................................................... 52

Limited Warranty ................................................................... 53

Spanish (Español) Quick Use Guide............................ 54 ~ 59

Index ....................................................................... Back Cover

Operation

DVD

Information

For Your

Page 6

DECK & Cassette Information

Head Cleaning

Playing older or damaged tapes may eventually cause video heads to become clogged.

Video Head Clog Sensor

During playback, this screen appears if clogging is detected. To remove screen, press PLAY on the remote or DECK.

• Use “dry” type head cleaning cassette only. (Part No. NV-TCL30PT is recommended.)

• Follow cleaning tape instructions carefully. Excessive use of tape can shorten head life.

• If head clog symptoms persist, contact your nearest Factory Servicenter or authorized Servicenter (see p. 52).

V I D

EO HEADS MAY

EED

CLEAN I NG PLEASE I NSERT HEAD CLEAN I NG CASSETTE OR REFER

MANUAL

END

: PL

Built-in Head Cleaner

A clean video head helps produce a clear picture. So, we have equipped your DECK with a built-in, non-chemical head cleaning system that helps prevent clogging of the video heads. Cleaning is performed each time you load or unload a video cassette.

• This feature is preventative only, If your video heads are seriously clogged, consider the use of a chemical non-abrasive head cleaning kit or take your DECK to a Servicenter.

Prevent Accidental Tape Erasure

Break off the tab to prevent recording.

Record Tab

Screw driver

To record again

Cover the hole with cellophane tape.

Record/ Playback Time

Only use tapes with the mark in this DECK.

Tape Speed

Setting

(Standard Play)

(Long Play)

SLP

(Super Long Play)

Type of Video Cassette

T160T120T60

1 Hour 2 Hours

2 Hours 4 Hours

2 Hours

40 Minutes

5 Hours

20 Minutes

3 Hours 6 Hours 8 Hours

Cleaning DECK

Use a soft cloth or dusting attachment of a vacuum cleaner to remove dust from the ventilation holes on the back sides and bottom of the cabinet. Plastic surfaces are easily scratched and can be marred by alcohol and various solvents. Avoid excessive use of oil-based furniture polishes since the materials used in the cabinet will accumulate more dust. We recommend using a non-abrasive, antistatic cleaner and polisher.

Features for a Quality Picture (VCR)

Digital Auto Picture

Automatically controls the video output signal for less noise depending on the tape condition.

Digital Auto Tracking

Continuously analyzes the signal and adjusts for optimum picture quality.

Manual Tracking Control (to reduce picture noise)

Use during Playback and Slow Motion mode to reduce picture noise. Press CH (TRACKING) / on the remote control or on DECK until the picture clears up. To return to Auto Tracking, press POWER off, then on again a few seconds later.

V-Lock Control (to reduce picture jitter) In Still mode, CH (TRACKING) / operate as a V-Lock control.

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : consumerproducts@panasonic.com

Page 7

Specifications

Power Source: 120 V AC, 60 Hz Power Consumption: Power On: Approx. 32 watts, Power Off: Approx. 4 watts

Video Signal: EIA Standard NTSC color Video Recording System: 4 rotary heads helical scanning system

Audio Track: 1 track (Normal), 2 channel (Hi-Fi Audio Sound) Tuner: Broadcast Channels: VHF 2 ~ 13, UHF 14 ~ 69 CABLE Channels: Midband A through I (14 ~ 22), Superband J through W (23 ~ 36)

Input/Output Terminal: Audio/Video Line Input/Output, RF Input/Output Input Terminal: Audio/Video Line Input (Front) Output Terminal: S-VHS Output (DVD only), Component Video Output (DVD only)

Operating Temperature: 5 °C ~ 40 °C (41 °F ~ 104 °F) Operating Humidity: 10 % ~ 75 % Weight: 6.9 kg (15.2 lbs). Dimensions: 430 (W) x 118 (H) x 364 (D) mm

Discs Played (1) DVD-VIDEO Disc 5” (12 cm) single-sided single-layer

(2) Compact Disc 5” (12 cm) disc

(CD-DA, VIDEO CD) 3” (8 cm) disc

Digital Audio Output: Digital Optical Connector Pickup: Wavelength: 655 nm (DVD), 790 nm (Video CD/CD)

Note: • Designs and specifications are subject to change without notice.

Hyperband AA ~ EEE (37 ~ 64), Lowband A-5 ~ A-1 (95 ~ 99) Special CABLE channel 5A (01), Ultraband 65 ~ 94, 100 ~ 125

Audio Output 2 (L), (R)

16-15/16” (W) x 4-5/8” (H) x 14-5/16” (D) inch

5” (12 cm) single-sided double-layer 5” (12 cm) double-sided double-layer (one layer per side) 3” (8 cm) single-sided single-layer 3” (8 cm) single-sided double-layer 3” (8 cm) double-sided double-layer (one layer per side)

Laser power: CLASS II

Definition of Terms (DVD)

Angle: Some DVD discs feature scenes simultaneously shot from different angles.

Chapter Number: Titles are subdivided into numbered sections. You can quickly search for

DVD: A high-density optical disc on which high-quality pictures and sound have

Playback Control:With Video CD (version 2.0), scenes or information may be selected for

Subtitles: Written dialogue which appears at the bottom of the screen. Time Number: The elapsed play time from the start of a disc or title. Use to quickly find

Title Number: For DVD discs with two or more titles, the title is numbered as title 1, title 2, etc. Track Number: Numbers assigned to tracks on Video CDs and CDs to allow specific tracks

Video CD: CD containing picture and sound with same quality level as video tape.

This product incorporates copyright protection technology that is protected by method claims of certain U.S. Patents and other intellectual property rights owned by Macrovision Corporation and other rights owners. Use of this copyright protection technology must be authorized by Macrovision Corporation, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision Corporation. Reverse engineering or disassembly is prohibited.

The ANGLE button can be used to view the scene from different angles. (ANGLE Indicator lights on DECK when a scene recorded at different angles is detected.)

a favorite scene using these numbers.

been digitally recorded. DVD incorporates new video compression technology (MPEG II) and high-density recording technology which allow entire movies to be recorded with incredible playback quality.

viewing or listening from an interactive menu that appears on the TV screen.

scenes. (May not work with some discs.)

to be quickly located.

This DECK also supports Video CDs with playback control (version 2.0).

(Connection)

Initial Setup

Page 8

Location of Controls

Remote Control

EJECT/

OPEN/CLOSE

pp. 20,

POWER

VCR mode

p. 28

DSS/CABLE mode

p. 28

PLAY

pp. 20,

REWIND/

SLOW-

pp. 20,

VCR/TV

p. 21

NUMBER keys

RETURN

pp. 22,

ACTION

pp. 18

SKIP SKIP

p. 23

TITLE

p. 38

/ SEARCH

, 45

Bold: VCR Function

Italic

DVD Function

Bold Italic:VCR and DVD Functions

Normal: Others

DISPLAY

p. 11,

TV mode

p. 28

DVD mode

p. 28

INPUT

p. 35

FAST FORWARD/

ADD/DELETE/

SURROUND/

SLOW+

pp. 20,

PAUSE

pp. 20,

CLEAR

pp. 19,

ENTER

pp. 23,

PROGRAM

/STILL

STOP

39, 44

p. 24

SELECT

p. 38

SET

ANGLE

p. 37

AUDIO

(SAP/ Hi-Fi)

pp. 27,

VOLUME +/

p. 28

COMMERCIAL SKIP/

TRACKING/V-LOCK

COUNTER RESET

p. 32

SPEED

p. 21

EJECT button: When this button is pressed in VCR mode, the tape is ejected.

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : consumerproducts@panasonic.com

This button is inoperative if pressed during recording. If pressed in DVD mode, the disc tray opens or closes.

SUB TITLE

p. 36

ZOOM

p. 37

ZERO

pp. 31, 32

CHANNEL /

pp. 21, 6

TAPE POSITION/

AUDIO CONTROL

p. 34,

RECORD

p. 21

Page 9

Front View of DECK

Bold: VCR Function

Italic

DVD Function

Bold Italic

Normal: Others

STOP/EJECT

p. 20

FAST FORWARD/SEARCH

p. 20

PLAY

p. 20

VCR and DVD Functions

If the disc cannot be removed...

First, unplug DECK. Then, prepare a rigid wire (e.g. an extended paper clip) and, applying moderate force, insert it straight into the hole at the base of the tray. The tray will eject a little. Now, pull the tray all the way out and remove the disc.

Over 2 inches

(Connection)

Initial Setup

REWIND/SEARCH

p. 20

POWER

Audio/Video Input Connector 2 (LINE 2)

CHANNEL / TRACKING/V-LOCK

pp. 21, 6

VCR/TV

p. 21

p. 35

Cassette Compartment

Multi Function

Display

p. 11

OPEN/CLOSE

Disc Tray

PROGRESSIVE

pp. 10, 13

Remote

Sensor

SKIP SKIP

p. 22

PAUSE

p. 23

PLAY

p. 22

p. 23

REC

p. 21

STOP

p. 22

Page 10

Location of Controls (continued)

Rear View of DECK

AC Power Plug

• While plugged into an AC outlet,

Bold: VCR Function

Bold Italic:VCR and DVD Functions

VHF/UHF Antenna Output Terminal p.12

Italic:DVD Function

this DECK consumes 4 W of electrical power in off mode.

Component Video Output Connector (Y, P p. 13

SELECT SW (DVD Only) p. 13

Optical Digital Audio Output Connector (DVD Only) p. 15

, PR) (DVD Only)

DVD OUTPUT

DIGITAL

SEE MANUAL

AUDIO OUT

(PCM/BITSTREAM)

OPTICAL

S-VIDEO OUT

S-Video Out Connector (DVD Only) p. 10, 13

SELECT

Audio Output 2 Connector (L/R) p. 13

VHF/UHF Antenna Input Terminal p. 12

Video Output Connector p. 12

COMPONENT

VIDEO OUT

OUT

L AUDIO2

••

Video Input Connector p. 35

OUT IN1

VIDEO

AUDIO1

Audio Output 1 Connector (L/R)

IN FROM ANT.

VHF/UHF

OUT TO TV

Audio Input Connector (L/R) p. 35

p. 12

The following table shows the status of the output jacks when in VCR or DVD mode.

Video Output Audio Out 1 Audio Out 2

VCR

DVD

• PROG functions on the remote are not available when using Component Video Output

Note

and S-VIDEO OUT. Please set TV to either RF INPUT or VIDEO INPUT, and then press PROG.

YES YES

Component Video Output

N/A N/A

YES

➛

SELECT SW

(Switchable)➛YES

S-VIDEO OUT

To enjoy PROGRESSIVE SCAN video (PV-D4752 only)

(1). Connect

(See p. 13.)

(2). Set the “COMPONENT VIDEO OUT”/“S-VIDEO OUT”

DECK, to “COMPONENT VIDEO OUT.” (See above.)

(3). When the PROGRESSIVE button is pressed, the ON lamp lights up (see p. 9) and the

PROGRESSIVE SCAN signal is output from the

Note

• The PROGRESSIVE button can be operated when the DECK is in DVD function mode.

• The screen may shift off-center when using progressive output. Please adjust the screen

position if this occurs. (Refer to your TV manual.)

• The unit does not output video signals from the “VIDEO OUT” or “S-VIDEO OUT” terminals when the ON lamp is lit.

Component Video Output

to the component video input terminals of a television.

SELECT SWITCH

, in the back of the

Component Video Output Connector

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : consumerproducts@panasonic.com

Page 11

Displays (On Screen & Multi Function)

•

On Screen Displays (VCR)

Function & Channel Displays

CH 0 8

When a function button is pressed, e.g. PLAY, or you change channels, a 5-second display appears.

VCR Status & Clock Displays To display or remove overlay at right,

➛➛

➛ press DISPLAY.

➛➛

Rec Time Remaining (OTR mode only, see p. 21.)

Multi Function Display

VCR Indicator

Lights up when the VCR/TV selector is set to VCR.

Power Indicator

Lights up when power is on.

Function Status

Broadcast Audio Being Received (See p. 26.)

Hi-Fi Indicator

Lights up when Hi-Fi audio is monitored in Play mode.

Blank Tape/ No Video Signal Indications

Whenever a blank section of a tape comes up in Play mode, or when the selected channel has no broadcast signal with Weak Signal Display Feature (p. 33) set to OFF, the TV screen will turn solid blue.

Current Time

REC

1 2 : 0 0A

0 : 25

STER

EO SAP M

ONO

-0 : 1 2 : 3 4

CH 02

Channel

Counter

Tape Speed (See p. 6.)

Timer Indicator

Lights up when DECK is set for Timer Recording, or when One Touch Recording (OTR) is used. Flashes when Timer Recording is set, but a tape has not been inserted into DECK and when a power interruption occurs during Timer Programming.

(Connection)

Initial Setup

VCR mode Indicator

Lights up when DECK is VCR mode.

VCR

VCR REC

VCR REC Indicator

Lights up during recording.

Clock/ Status/ Channel/ Speed Display

Displays the current time. Briefly displays VCR status when a function button is pressed. Briefly displays the channel number, or “L1” or “L2” when a channel or line input is selected. Briefly displays the recording speed when SPEED is pressed.

VCR

TIMER

Hi-Fi

A M

DVD

ANGLE

Lights up before noon. PM is not displayed.

DVD mode Indicator

Lights up when DECK is DVD mode.

ANGLE Indicator

Lights up when a scene recorded at different angles is detected. See p. 37. (DVD only).

Page 12

Connections

Basic Connections

• If your TV has AUDIO and VIDEO IN terminals, connect them to DECK for higher

quality picture and sound.

• You can enjoy stereo sound even if your TV is not stereo by connecting a stereo

amplifier to DECK.

• Connect DECK and TV with an RF Coaxial Cable a (supplied) or an AV Cable (not supplied) as shown in the figure below.

■ ■

■ DSS Receiver DECK TV

■ ■

■ DECK TV

■ ■

Antenna or Cable

■ Cable Box DECK TV

■ ■

DSS Receiver

OUT

DVD/VCR DECK

IN FROM ANT.

IN 1

OUT

VIDEO

AUDIO

WARNING

When using “Nut type” RF coaxial cables, tighten with fingers only. Overtightening may damage terminals.

VHF/UHF

OUT TO TV

OUT

Cable Box

1 Disconnect antenna or cable from TV

and connect to DECK.

2 Connect DECK to TV with RF Coaxial Cable.

RF COAXIAL CABLE

VHF/ UHF

AUDIO IN

VIDEO

AV CABLE

(not supplied)

Note to CABLE system installer

This reminder is provided to call the CABLE system installer’s attention to Article 820-40 of the NEC in USA (and to the Canadian Electrical Code in Canada) that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical.

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : consumerproducts@panasonic.com

Page 13

Other Connections

■ ■

■ With a Cable Box (DECK

■ ■

DVD/VCR DECK

IN FROM ANT.

IN 1

OUT

VHF/UHF

OUT TO TV

■■

■

Connect With Two Cable Boxes

■■

ANT or CATV

Cable Box

Cable Box TV)

OUTIN

DVD/VCR DECK

ANT

CATV

Cable Box

OUT

2-Way Splitter

OUT 1

OUT 2

OUT

Cable Box

OUTIN

IN 1

IN FROM ANT.

VHF/UHF OUT TO TV

A/B Switch

IN 2IN 1

VHF/ UHF

• view any (including

• use Remote

• record and view

AUDIO

VIDEO

scrambled) channel.

Control to select channels without using Multi-brand control feature.

both scrambled and unscrambled channels if additional equipment is added. This connection requires: two converter boxes, an A/B switch, and a 2-way splitter.

OUT

AUDIO

VIDEO

OUT

R L

VHF/ UHF

You CannotYou Can

• record scrambled channels.

You CannotYou Can

• view channel other than the one selected for any type of recording.

• do a Timer recording of a channel unless you select it on the Cable Box.

Connections For DVD Only

Connect AUDIO OUT2 (L, R) to the AUDIO IN (L, R) of the TV. (audio input for COMPONENT

or S-VIDEO mode). If your TV has COMPONENT VIDEO INPUT, set SELECT SW to COMPONENT VIDEO OUT.

If your TV does not have COMPONENT VIDEO INPUT but has S-VIDEO INPUT, set SELECT SW to S-VIDEO OUT.

Note

Notes

• The picture will not be displayed if the SELECT SW is not set to the correct video output.

When in DVD mode, set your TV to either COMPONENT VIDEO IN or S-VIDEO IN.

• You can watch DVDs through the S-VIDEO or COMPONENT VIDEO, VHF/UHF OUT TO TV, and VIDEO OUT connections to your TV. The VCR and TUNER pictures are available only from the VIDEO OUT and VHF/UHF OUT TO TV connections to your TV.

• PROG functions on the remote are not available when using S-VIDEO OUT and COMPONENT

Video Output. Please set TV to either RF INPUT or VIDEO INPUT, and then press PROG.

DVD/VCR DECK

DVD OUTPUT

S-VIDEO OUT

SELECT

COMPONENT

VIDEO OUT

P R

AUDIO OUT2

AUDIO

VIDEO

S-VIDEO IN

From DECK’s

A/V OUTPUT

(Connection)

Initial Setup

Page 14

Connections (continued)

Audio Connections

Ready Checklist

Turn down the volume, then turn DECK, as well as other equipment to be connected, off before proceeding with connection. Do not block ventilation holes of any of the equipment and arrange them so that air can circulate freely. Read through the instructions before connecting other equipment. Ensure that you observe the color coding when connecting audio and video cables.

■ DECK

Amplifier

DVD/VCR DECK

AUDIO OUT2

Enjoying digital audio output from the digital audio output connector

Notes on audio output from the optical digital audio output connector

Disc

DVD

Video CD CD MP3

*1 The type of audio output from the connector can be selected by the Settings for DVD

Operation. (See p. 46.)

*2 Sound having 96 kHz sampling is converted into 48 kHz sampling when it is output

from the DECK’s optical digital audio output connector.

For your reference:

• Dolby Digital is a digital sound compression technique developed by the Dolby Laboratories Licensing Corporation. Supporting 5.1-channel surround sound, as well as stereo (2-channel) sound, this technique enables a large quantity of sound data to be efficiently recorded on a disc.

• Linear PCM is a signal recording format used in CDs. While CDs are recorded in 44.1 kHz/16 bit, DVDs are recorded in 48 kHz/16 bit up to 96 kHz/24 bit.

• If you have a Dolby Pro Logic Surround decoder, you will obtain the full benefit of Pro Logic from the same DVD movies that provide full 5.1 channel Dolby Digital soundtracks, as well as from titles with the Dolby Surround mark. For information on Panasonic or Technics Dolby Pro Logic Surround Sound Decoders please contact your local dealer.

Sound recording format

Dolby Digital

Linear PCM (48/96 kHz 16/20/24bit)

dts MPEG 1

Linear PCM

MP3

Speaker

Amplifier

Speaker

AUDIO IN

R L

Optical digital audio output from connector

Dolby Digital bitstream (1-5.1 ch) or OFF (no output)*

Linear PCM (2ch) (48 kHz sampling/16 bit only)*2 or no output*

Bitstream or no output*

PCM (44.1 kHz sampling) Linear PCM (44.1 kHz sampling)

Linear PCM (It depends on the MP3 file)

Manufactured under license from Dolby Laboratories. “Dolby,” “Pro Logic” and the double-D symbol are trademarks of Dolby Laboratories. Confidential Unpublished Works. © 1992-1997 Dolby Laboratories, Inc. All rights reserved.

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : consumerproducts@panasonic.com

Page 15

■ DECK Dolby Digital Decoder Amplifier Speaker

DECK dts (digital theater systems) Decoder Amplifier Speaker

When DVDs recorded in Dolby Digital or dts are played, Dolby Digital bitstream or dts bitstream is output from the DECK OPTICAL digital audio output connector. When DECK is connected to a Dolby Digital decoder or dts decoder, you can enjoy theater-quality audio in your home. [An optical digital audio cable (optional) is required when an optional Dolby Digital decoder or dts decoder is used.]

Notes on connecting an optical digital audio cable (optional)

• Firmly connect the cable to the connector.

(Connection)

Initial Setup

Surround Speaker

Center Speaker

Decoder with Dolby

DVD/VCR DECK

OPTICAL

Optical Digital Audio Cable (optional)

Caution for optical digital audio output connector:

• When connecting an amplifier (with an optical digital input connector) which does not contain the Dolby Digital or dts decoder, be sure to select “OFF” at “Dolby Digital” and “OFF” at “dts” of the Settings for DVD Operation “AUDIO OUTPUT” (see p. 46). Otherwise, any attempt to play DVDs may cause such a high level of noise that it may be harmful to your ears and damage your speakers.

• When a dts decoder is connected, please select “Bitstream” at “dts” of the Settings for DVD Operation “AUDIO OUTPUT”. If “OFF” is selected, there will be no sound. (See p. 46).

• Video CDs and CDs can be played as usual.

Note:

• Some dts decoders which do not support DVD-dts interface may not work properly with DECK.

Digital dts processing (optional)

To Optical Digital Audio Input Connector

Front Speaker

Amplifier

Surround Speaker

Front Speaker

Subwoofer

Page 16

Initial Setup for Basic Connections (Ready to Play)

Before doing Initial Setup

Turn TV on.

See connections a RF Coaxial Cable Connection and b AV Cable Connection on p. 12.

<RF Coaxial Cable Connection> Set TV to channel 3.

Set TV to VIDEO.

[DECK

• Go to “Doing Initial Setup (Ready to Play).” (See below.)

[Cable Box

• Turn on Cable Box and set it to your Public Broadcasting Station (PBS) channel

• If you use a DSS Receiver, it must be turned off.

Doing Initial Setup (Ready to Play)

Press VCR on remote for VCR mode.

Plug DECK Power Cord into AC wall outlet. DECK comes on and auto channel and clock set starts.

• If screen below does not appear, check DECK - TV connection and, if TV is tuned to

• To change VCR’s output channel, please refer to “VCR’s Output Channel” on p. 19.

➛➛

➛ TV]

➛➛

➛ DECK

➛➛

in your time zone.

channel 3, try switching it to channel 4.

➛➛

➛ TV], [DSS

➛➛

➛ DECK

➛➛

➛ TV]

➛➛

Plugging the AC Power Plug into an AC outlet

CH AUTO SET PROCEEDING

CANCEL : STOP

AUTO CLOCK SET

PROCEEDING

CANCEL : STOP

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : consumerproducts@panasonic.com

Page 17

*Important: If a remote control button does not work when pressed,

press the VCR button on the remote and try the button again.

ACTION

SELECT

SET

Settings are made automatically. When setup is done, this screen appears.

9 / 29 / 20 02 SUN 2 : 20P

SETT I NG

: CH

AUTO CLOCK SET

COMPLETED

DST :

If “AUTO CLOCK SET IS INCOMPLETE” appears, manually set clock. See below.

AUTO CLOCK SET IS I NCOM

PLETE

PLEASE SET CLOCK BY

ACT I ON KEY

PRESSING

Manual Clock Set

If Auto Clock Set was incomplete.

Press ACTION* on remote to display CLOCK screen.

SET CLOCK

1 / /

- - - - - - - - -- - - - - - - -- - - - - -

SELE CT MONTH

SELECT : SET :SET EXIT

: ACT I ON

DST : O

(Connection)

Initial Setup

Press set. In the same manner, select and set the

to select the month and SET to

date, year, time, and DST (daylight saving time).

SET CLOCK

9 / 29 / 2002 SUN 2: 2 0 PM

- - - - - - - - -- - - - - - - -- - - - - -

SET COMPLETE

SET : S START :

Press ACTION to start clock and exit.

DST :

ET BACK :

ACT I O

Page 18

SELECT : EXIT

: ACTION

SET : SET

MENU SET UP VCR

SET CLOCK

SET UP CHANNEL IDIOMA/LANGUE : ENGLISH VCR’S OUTPUT CH:3

Reset Language, Channels, Clock

AUTO CLOCK SET

MANUNU

T I M

E ZONE AD

JUS

T :

SELECT :

SET :

SET

EXIT

: ACT I ON

SET CLOCK

DST :

9 / 30 / 2002 SUN 12: 0 0 PM

SELECT HOUROUR

- - - - - - - - -- - - - - - - -- - - - - -

SET CLOCK

SELE

CT :

SET

SET BACK :

EXIT

: ACT I ON

SET UP VCR

SET CLOCK SET UP CHANNEL IDIOMA/LANGUE : ENGLISH VCR’S OUTPUT CH:3

SELECT :

: ACTION

SET:SET

EXIT

Language

1) Press to select

language item.

MENU SET UP VCR SET CLOCK SET UP CHANNEL

IDIOMA/LANGUE : ENGLISH

VCR’S OUTPUT CH:3

SELECT : EXIT

: ACTION

2) Press SET repeatedly.

MENU PREPARAR VCR FIJAR RELOJ FIJAR CANAL

LANGUE/LANGUAGE:ESPAÑOL

CANAL DE SALIDA : 3

ELEGIR : SALIR

MENU REGLAGE MAGNETOSCOPE REGLAGE HORLOGE REGLAGE CANAL

LANGUAGE/IDIOMA:FRANÇAIS

CA SORTIE : 3

SEL. : QUITTER

MENU SET UP VCR SET CLOCK SET UP CHANNEL

IDIOMA/LANGUE : ENGLISH

VCR’S OUTPUT CH:3

SELECT : EXIT

: ACTION

3) Press ACTION to exit.

SET:SET

FIJAR : SET

: ACTION

For Spanish

REGLER:SET

: ACTION

For French

SET:SET

For English

Press ACTION*

to display MENU.

Channels

1) Press to select

“SET UP CHANNEL,” and press SET.

MENU SET UP VCR SET CLOCK

SET UP CHANNEL

IDIOMA/LANGUE : ENGLISH VCR’S OUTPUT CH:3

SELECT : EXIT

: ACTION

2) Press to select

“ANTENNA,” then press SET to set your antenna system (“TV” or “CABLE.”)

SET UP CHA

ANT

ENNA

AUTO SET WEAK

C VCR Plus+ CH SET UP

3) Press to select

• If you use a Cable Box,

CH AUTO SET PROCEEDING

CANCEL : STOP

• After Channel Auto Set

CABLE

S I GNAL D I

ABLE / DSS BOX SET UP

SELECT : EXIT

: ACT I ON

“AUTO SET,” then

press SET.

set it to the PBS channel in your time zone.

is finished, Auto Clock Set will be performed.

• PROGRAM functions are not available when using COMPONENT Video Output and S-VIDEO OUT. Please set TV to either RF INPUT or VIDEO INPUT, and then press PROGRAM.

Clock

1) Press to select

“SET CLOCK,” and

press SET.

SET : SET

2) Press to select “MANUAL,” and press SET. (For Auto Clock Set, select “AUTO CLOCK SET.”)

NNE

SPLAY : OFF

SET : SET

(“TIME ZONE ADJUST”

appears only when auto clock is set.)

3) Press and to

select, then set the date, time, and DST (Daylight Saving Time).

4) Press ACTION to start

Clock and exit this mode.

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : consumerproducts@panasonic.com

Page 19

HANNEL

08 ADDED

HANNEL

08 DELE T

*Important: If a remote control button does not work

when pressed, press the VCR button on the remote and try the button again.

POWER

VCR

Time Zone Adjust

(Only when Auto Clock is set.)

1) Press to select

“SET CLOCK,” and press SET.

MENU SET UP VCR

SET CLOCK

SET UP CHANNEL IDIOMA/LANGUE : ENGLISH VCR’S OUTPUT CH:3

SELECT : EXIT

: ACTION

2) Press to select

“TIME ZONE ADJUST,”

AUTO CLOCK SET MANU

T I M

SELECT : EXIT

: ACT I ON

and press SET to subtract or add hour(s) as necessary.

3) Press ACTION twice.

•“TIME ZONE ADJUST” returns to “0” if clock is set manually.

SET : SET

SET CLOCK

E ZONE AD

JUS

SET : SET

T :

VCR’s Output Channel

1) Press to select

“VCR’S OUTPUT CH.,” and press SET.

MENU SET UP VCR SET CLOCK SET UP CHANNEL IDIOMA/LANGUE : ENGLISH

VCR’S OUTPUT CH:3

SELECT : EXIT

: ACTION

2) Press SET.

I F YOU PRESS KEY, VCR’ SW I

TCHES TO

3) Press ACTION.

PLEASE TUNE YOUR TV TO CH 4.

After 3 seconds

MENU SET UP VCR SET CLOCK SET UP CHANNEL IDIOMA/LANGUE : ENGLISH

VCR’S OUTPUT CH:4

SELECT : EXIT

: ACTION

• To Make Corrections, repeat steps 1) ~ 3).

SET : SET

ACT I O

S OUTPUT CH

CH 4.

SET : SET

NUMBER keys

ACTION ADD/DLT

SELECT

SET

CH /

Add or Delete a Channel

To add channel: Select channel with NUMBER keys

and press ADD/DLT.

To delete channel: Select channel with CH / or

NUMBER keys and press ADD/DLT.

DST (Daylight Saving Time)

DECK auto adjusts clock for DST. (p. 17.)

Spring (First Sunday in April)

DST:ON

Autumn (Last Sunday in October)

DST:ON

➛➛

➛ Sets clock ahead one hour.

➛➛

➛ Turns clock back one hour.

➛➛

Operation

Basic

• If your area does not observe Daylight Saving Time, select DST:OFF.

• Keep these time changes in mind when programming DECK for timer recordings.

Page 20

Playback/ Record on a Tape

Ready Checklist

All connections are made (pp. 12 ~ 15). TV and DECK are plugged in. TV is on and tuned to CH3, 4, or VIDEO. Remote is in VCR mode. (Press VCR.)

Playback a Tape

Insert a tape.

• DECK power comes on. The VCR mode and “VCR” indicator light up on Multi Function Display.

Press PLAY* to play a tape.

• If tape has no rec. tab (p. 6), auto play begins.

Special Features During Play

Forward/Reverse Scene Search

➛➛

➛ Press FF/SLOW+ or REW/SLOW-.

➛➛ ➛➛

➛ Press PLAY to release.

➛➛

After search has begun, each additional press of FF or REW changes speed as shown below.

[SLP] : Approx. 21X [LP] : Approx. 9X [SP] : Approx. 7X

If at 21X, 9X, or 7X speed the picture is interrupted, change speed to 9X, 7X, or 3X.

Notes

• Picture interruption may occur with some TVs.

• FF and REW search speed may vary

depending on current tape position.

Still (Freeze) Picture

➛➛

➛ Press PAUSE/STILL.

➛➛ ➛➛

➛ Press PLAY to release.

➛➛

Frame by Frame Picture

➛➛

➛ Press PAUSE/STILL in Still mode.

➛➛ ➛➛

➛ Press PLAY to release.

➛➛

Slow Motion Picture

➛➛

➛ Press FF/SLOW+ (increase speed) or

➛➛

REW/SLOW- (decrease speed) in Still mode.

➛➛

➛ Press PLAY to release.

➛➛

↔ Approx. 9X ↔ Approx. 7X ↔ Approx. 3X

EJECT

REW/SLOWVCR/TV STOP

Notes

• These features work best in SP or SLP mode.

• The sound will be muted.

• To reduce picture noise, see “Manual Tracking Control” on p. 6.

• After DECK is in Still or Slow mode for 3 minutes,

it will switch to Stop mode automatically to protect the tape and the video head.

DVD

PLAY

FF/SLOW+ PAUSE/

STILL

CH /

REC

SPEED

Playback using DECK buttons

Press PLAY.

Insert a tape.

Press STOP to stop a tape.

Press REW/SLOW- or FF/SLOW+ in Stop mode to rewind or fast forward a tape.

Press EJECT on remote, or STOP/EJECT

on DECK to eject a tape.

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : consumerproducts@panasonic.com

Multi Function Display

Press STOP/EJECT to stop and/ or eject a tape.

Page 21

*Important: If a remote control button does not work when pressed,

press the VCR button on the remote and try the button again.

Record on a Tape

Insert a tape with a record tab (p. 6).

• DECK power comes on. The VCR mode and “VCR” indicator light up on Multi Function Display.

Press CH , or NUMBER keys

to select the channel.

• For “LINE” input, see p. 35.

• If channel is over 100, press 100 key then press

the remaining 2 digits.

Press SPEED

to select the record speed (p. 6).

SP = Standard Play LP = Long Play SLP = Super Long Play

• Speed appears on-screen and on Multi Function Display.

Press REC

to start recording.

(The VCR REC indicator lights up on Multi Function Display),

• To edit out unwanted scenes, press PAUSE/STILL to pause, and again to resume recording.

• You cannot view another channel during recording.

Press STOP

to stop recording.

One Touch Recording (recording in progress),

➛➛

➛ Press REC repeatedly to set the recording length

➛➛ ➛➛

➛ (30 min. ~ 4 hours).

➛➛

• DECK shuts off after the preset record length.

Record one station, watch another,

➛➛

➛ press VCR/TV

➛➛

(“VCR” goes out on Multi Function Display),

➛➛

➛ select channels at TV (recording continues).

➛➛

Select Channels at DECK (In STOP or REC. PAUSE mode),

➛➛

➛ press VCR/TV

➛➛

(“VCR” lights up on Multi Function Display),

➛➛

➛ select channels at DECK.

➛➛

Play a disc while recording a tape.

➛➛

➛ insert a disc during recording,

➛➛ ➛➛

➛ press

➛➛

DVD

, and then press

PLAY

This video recorder, equipped with HQ (High Quality) system, is compatible with existing VHS equipment. Only use tapes with the mark. Only tapes tested and inspected for use in 2, 4, 6, and 8 hour machines are recommended.

Note

Remove loose or peeling labels from tapes to prevent tape jam.

Normal Rec

0:30 1:00

1:302:003:004:00

Record using DECK buttons

Insert a tape.

VCR/TV

Press REC to start Recording.

Operation

Basic

Notes

• It is not possible to record from DVD/ Video CD/ CD to VHS tape using DECK.

• Watching one channel and recording another is not possible when using Cable Box or DSS Receiver.

• After 5 minutes in Pause mode, DECK stops to protect a tape and video heads.

Select

Channel.

Multi Function Display

Press STOP/EJECT to stop.

Page 22

Basic DVD Operation

Ready Checklist

All connections are made. (pp. 12 ~ 15) DECK is plugged in. If DECK is connected to an audio amplifier,

turn the stereo system’s power on.

POWER

PLAY

REW/ SLOW-

STOP

NUMBER

keys

RETURN

SKIP SELECT

SET

TITLE

OPEN/ CLOSE

DVD

FF/ SLOW+

PAUSE/ STILL

SURROUND

SKIP

1 2

If an interactive DVD*1 or a Video CD with playback control*2 is used and TITLE MENU appears, go to step 5.

Press

POWER*

DVD

Press

• If a disc is already inserted, go to step 4. (Depending on the disc, playback may start automatically.)

Press

OPEN/CLOSE

and then place a disc into the disc tray.

Press

PLAY

Disc tray closes automatically.

READING

on the remote or DECK.

to select DVD mode.

• Hold disc by its edges only (p. 4) with printed side up and use guides to

place into tray.

Use 3”(8 cm)

or 5” (12 cm) disc.

to start playing.

• You may also close tray by

pressing

• Data reading time differs with each disc.

OPEN/CLOSE

T I TLE MENU

Dogs

Love

Cas t l es

i r

Operation using DECK buttons

Press

3, 7

OPEN/CLOSE.

Insert a disc.

Press

POWER

*1Interactive DVD...

May include multiple camera angles, stories, etc.

*2Video CD with playback control...

Particular scenes or information can be interactively selected from a menu that appears on the screen.

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : consumerproducts@panasonic.com

Press PLAY.

Press STOP.6

T I TLE MENU

Using NUMBER keys starts playing automatically.

<Example> 1 digit number 1 ••• 1

Press menu screen.

• SKIP function not available with all discs. Please refer to disc jacket for operation information.

To return to menu (play stops)

Press Press

Press

Cas t l es

Dogs

i r

Love

SKIP

TITLE, MENU, RETURN

Dogs

of the world

2 digit number 12 ••• 10 1 2 3 digit number 123 •••100 1 2 3

| or | to go to next or previous

. (Video CD)

STOP

OPEN/CLOSE

Press or

NUMBER keys

below) to select title, and

press

SET

RETURN

to stop playing.

. (DVD)

to eject the disc.

(see

to play.

Page 23

*Important: If a remote control button does not work when pressed,

press the DVD button on the remote and try the button again.

■ Forward/Reverse Scene Search

Press

FF/SLOW+

REW/SLOW-

during play.

PLAY

Press

• Starting forward/reverse search during play started from menu on Video CDs may recall menu.

• Search speed, slow at first, increases with each additional press of the button up to 5 levels.

to release.

■ Forward/Reverse Chapter/Track Skip

Press

SKIP

| or |

SKIP

during play. Each press skips a chapter (DVD) or track (Video CD/CD).

• Pressing |

chapter/track returns to the start of that chapter/track. Each additional press skips back one chapter/track.

• Pressing

from menu on Video CDs may recall menu.

Chapter/Track Chapter/Track Chapter/Track

Reverse Skip Forward Skip

SKIP

once midway through a

SKIP

| or | during play started

Current playback position

Chapter/Track

■ Still Picture or Pause

Press

PAUSE/STILL

Press

PLAY

to release.

• DVD/Video CD : DECK will enter still picture

• CD : DECK will enter pause mode.

during play.

mode.

■ Frame by Frame Picture

(DVD/Video CD) Press

PAUSE/STILL

PLAY

Press

• Each press advances picture one frame.

• Hold button down for consecutive frame advance.

• Whether pictures are advanced by “FRAME” or

“FIELD” is selected automatically. (See p. 47)

to release.

in still mode.

■ Slow Motion Picture (DVD/Video CD)

Press

FF/SLOW+

in still mode.

Press

PLAY

• Slow motion speed, slow at first, is increased

with each additional press of the button up to 5 levels.

• Reverse slow motion is not available for Video

CDs.

• When appears on the screen while a button

is being operated, it means that the corresponding operation is prohibited by DECK or the disc.

REW/SLOW-

to release.

Surround Sound System

Press

SURROUND

SURROUND ON

SURROUND OFF

to set Surround sound.

To cancel, press

SURROUND

Note

• Surround sound effects is available in DVD mode only.

Resume Function

DECK memorizes the point where STOP is pressed ( flashes on screen).

Press

PLAY

Pressing

cancels RESUME, however, RESUME is not canceled when power is turned off and on.

• RESUME works only with discs for which elapsed play time is displayed during play.

to resume play from this point.

STOP

again or opening the tray

Auto-Power Off Function

Power turns off after DECK has been in Stop mode (DVD) for about 5 minutes.

Enjoy Video CDs featuring playback control without using menus (Video CDs only)

1. Do steps 1-4 (previous page).

When menu appears, press

2. Press

NUMBER keys

track (play begins).

• Check disc for track numbers.

• Press “1” to start at beginning of disc.

To Resume Menu use,

Press

STOP

menu will be displayed. Now, go to step 5 (previous page).

and press

Notes

• Please read the disc jacket for operation information.

• If a single sided disc is placed in upside down, “PLEASE CHECK THE DISC, AND FOR STAINS OR SCRATCHES ON DISC” is displayed.

• Remove disc and press DECK POWER off when not in use.

• Disc continues to rotate with menu displayed even after play is done.

Press STOP to clear menu display when finished with menu.

STOP

to select desired

PLAY

, then the

Operation

Basic

Page 24

Timer Recording

•

Ready Checklist

All connections are made (pp. 12 ~ 15). TV and DECK are plugged in. Clock set correctly. Tape has rec.tab. (p. 6) Remote is in VCR mode. (Press VCR.) Sufficient tape remaining for recording time.

Press PROG*

to display Program.

POWER

DATE START ST

SUN --:-- --:-- --

TODA

- - - - - - - - -- - - - - - - -- - - - - - -

SESELE CT START DAT

CT :

SELE SET

END

: PROG

Example

Today

SELECT /

Selection Order

WEEKLY

(SAT)

START

13 10 : 00 P 12 : 00 P 02

-- -- : --

-- : -- -- : -- --

CANCEL : ADD / DLT SELECT 1-8 : E

NTER

EXIT

: PROG

OPC

SET

STOP CH

-- : -- --

: SET

1) To set record DATE,

SLP

press

1~31= one time, or DAILY= MON~ FRI, or WEEKLY= same time each week and press SET.

• See selection order left.

2) To set remaining items,

DAILY

WEEKLY

(SUN)

WEEKLY

(MON)

press

to select and

press SET

to set START/ STOP times, CH(channel) or LINE input (p. 35), and tape speed (SP, LP, SLP).

Press PROG

to end programming.

To Enter More Programs,

SPD

press

to select and

press SET

to set an unused program number, and then repeat step 2.

Press PROG

to exit.

to select:

VCR mode Indicator

Multi Function Display

VCR

VCR REC

VCR REC Indicator

ADD/DLT

PROG

SELECT

SET

VCR

TIMER

Hi-Fi

A M

TIMER Indicator

DVD

ANGLE

• The “Timer” Indicator lights up on DECK.

• You can do Timer Recording with the power or off.

•“TIMER REC WILL START SOON” appears on-screen for 2 minutes

before Timer Recording starts. If DECK is in DVD mode, no message appears, but the VCR REC Indicator, the VCR mode indicator and “REC” will flash on Multi function Display.

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : consumerproducts@panasonic.com

Page 25

*Important: If a remote control button does not work when pressed,

press the VCR button on the remote and try the button again.

Review, Replace or Clear Program Contents:

(Recording is not in progress)

Press PROG

to display Program List.

START

STOP CH

7 9 : 00A 12 : 00A 08

10 : 00P

12 : 00P 02 SP

8 : 00P

9 : 00P 10

9 : 00P 10 : 00P

CANC

EL : ADD /

SELECT

1-8 : ENTER : SET EXIT

: PROG

DLT

To Replace program...

DATE

TART

9:00A 12:

START DAT

SET

: PROG

STOP CH

-- : -- -- 12 : 00P 02 SP 9 : 00P 10

DLT

1-8 :

: PROG

TOP

00A 08

7 SUN

TODA

----------------------------------------

SELE CT

SELECT : SET

END

To Clear program...

START

-- -- : --

10 : 00P

8 : 00P

SU 9 : 00P 10 : 00P

CANC

EL : ADD / SELECT ENTER : SET EXIT

Press PROG

to end the programming.

SPD

SP LP

BACK :

SPD

Press

to select number and

press SET

to display.

Repeat Step 2 (p. 24) to set new programs.

Press ADD/DLT.

To cancel a Timer Recording in progress...

Hold down STOP on VCR mode for

a few seconds to cancel the Timer Recording.

(The “TIMER” Indicator goes out on Multi Function Display.)

• Any future daily or weekly recording will be performed as programmed.

Operation

VCR

Notes

• If you are using a Cable Box, the VCR’s channel for Timer Recording must be set to the Cable Box input channel and Cable Box must be manually set to the desired channel. Cable Box power must be left on.

• 2 minutes before Timer Recording is performed, “PLEASE PREPARE FOR TIMER REC” appears and Timer Indicator flashes. Be sure a cassette with record tab is loaded and DECK is in Stop mode.

• If a power interruption occurs while programming the timer, the timer program(s) may be canceled. If “TIMER PROGRAMS WERE LOST DUE TO POWER INTERRUPTION” appears on-screen, please re-enter the timer programs.

• If the start time for Timer Recording comes up during recording and playing back, Timer Recording will not be performed.

Important notes when using DSS Receiver

• When recording programs via DSS Receiver, DSS Receiver must be left on.

• When recording programs via an antenna or cable, DSS Receiver must be turned off.

Page 26

MTS Broadcast/ VHS Hi-Fi Stereo System

Connection

Make the Audio/Video Connection as shown on pp. 12 ~ 15.

• You can use TV connected to a Stereo amplifier and speakers instead of Stereo TV.

Receivable Broadcast Types

The following are possible audio broadcast types and onscreen displays.

The signal being received is indicated with an “

” mark

while the selected audio mode is indicated with an arrow.

To display the broadcast signal being received,

➛➛

➛ press DISPLAY*.

➛➛

MTS Stereo and SAP broadcast

Multi-channel Television Sound Stereo (main language) and Secondary Audio Program (sub language) broadcasts are being

STOP 1 2 : 0 0A

STER

EO SAP M

ONO

0 : 0 0 : 0 0

CH 02

received simultaneously. Select STEREO or SAP audio mode.

DISPLAY

MTS Stereo broadcast

Multi-channel Television Sound Stereo broadcast. Select STEREO audio mode.

• If stereo broadcast is weak and display flickers, select MONO audio mode for possible better results.

SAP broadcast

Secondary Audio Program (sub language) broadcast. Select SAP audio mode for the sub language.

MONO broadcast

Normal monaural sound broadcast.

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : consumerproducts@panasonic.com

STOP 1 2 : 0 0A

STER

EO SAP M

ONO

STOP 1 2 : 0 0A

STER

EO SAP M

ONO

STOP 1 2 : 0 0A

STER

EO SAP M

ONO

0 : 0 0 : 0 0

CH 02

AUDIO

Equipped with ®-TV

(SAP/Hi-Fi)

Noise Reduction for true MTS reproduction.

-TV Noise Reduction is required for good stereo

separation and audio fidelity.

is a registered trademark, and is licensed by

Technology Licensing.

Page 27

*Important: If a remote control button does not work when pressed,

press the VCR button on the remote and try the button again.

Audio Mode for Recording

Press AUDIO (SAP/Hi-Fi)

to display audio mode.

(Display disappears after 5 seconds.)

Press AUDIO (SAP/Hi-Fi) repeatedly

STER

EO SAP M

ONO

Do a recording.

See p. 21.

to select desired mode.

• Refer to “Receivable Broadcast Types” on p. 26.

• Arrow indicates selection.

Operation

Audio Mode for Playback

Start playback.

See p. 20.

Press AUDIO (SAP/Hi-Fi)

to display audio mode.

H I F I

: L / R

H I F I

: L

H I F I

ORM

• Arrow indicates selection.

Notes

• Only tapes recorded in Hi-Fi stereo will playback with true stereo sound. Standard stereo tapes will playback in monaural sound.

• To listen to Hi-Fi stereo playback, the DECK AUDIO (L/R) jacks must be connected to a stereo TV or an external stereo amplifier and speakers. (See pp. 12, 14, 15.)

• If tracking is adjusted during playback, Hi-Fi audio may revert to normal audio.

• Hi-Fi and normal audio playback volume level may differ.

Press AUDIO (SAP/Hi-Fi) repeatedly to select desired mode.

• Select “HIFI (L/R)” or “HIFI (L)” or “HIFI (R)” to listen to stereo recordings in stereo sound. Select “NORMAL” for monaural sound.

• Display disappears after 5 seconds.

VCR

Page 28

Multi-Brand Control Feature

Multi-Brand Control Setup

The Remote Control can be set to control some TV and Cable Box/DSS functions.

Find your TV and Cable Box/DSS Receiver

Brand Code Number on the following page.

Setup for TV control,

➛➛

➛ hold down TV button,

➛➛ ➛➛

➛ enter code with NUMBER keys.

➛➛

Setup for Cable or DSS control,

➛➛

➛ hold down DSS/CABLE button,

➛➛ ➛➛

➛ enter code with NUMBER keys.

➛➛

• If code number is 100 or greater,

➛ e.g., press 1 - 0 - 2 for 102.

Confirm code entry,

➛ press POWER to turn selected unit on or off.

• See table below for controllable functions in each mode.

Notes

• Repeat setup after remote battery replacement.

• Remote will not control every TV, Cable Box, or

DSS made by the manufacturer listed. If you get no response, your particular unit cannot be controlled. There are NO additional codes for the products listed. If your product is not listed, then the remote is not compatible with that product.

Using Multi-Brand Control

After remote is set up, you can select VCR, DVD, TV, or DSS/CABLE for the desired function.

Press VCR,

(Table below shows available remote buttons for each mode.)

Mode

Unit

DVD

, TV, or DSS/CABLE on the remote.

DVD/VCR TV

CABLE/ DSS

POWER

VCR

DSS/ CABLE

DVD

NUMBER keys

ENTER

DVD/VCR

CABLE/ DSS

Notes

• Not all functions listed may be controllable.

• In TV or DSS/CABLE mode, it may be necessary to press ENTER after pressing

NUMBER keys for channel selection.

EJECT/

DISPLAY, PLAY, STOP FF/SLOW+, REW/SLOW-

VCR/TV, PAUSE

AUDIO

TAPE POSITION, COUNTER RESET , SPEED, REC

* Bold: VCR Function

Italic: DVD Function

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : consumerproducts@panasonic.com

All

OPEN/CLOSE

/STILL, SKIP

, CM/ZERO,

VOL +/

POWER, INPUT, NUMBER keys, ENTER, CH / ,

VOL +/

POWER, ENTER,

VOL +/-

Bold Italic: VCR and DVD Functions

Normal: TV, Cable Box or DSS Receiver

NUMBER keys (except 100key), CH /

Page 29

TV Brand Code Numbers

Panasonic ....................... 01, 02

Quasar ............................ 01, 02

RCA ....................................... 03

GE ......................................... 03

Zenith .................................... 04

Magnavox .............................. 05

Sylvania ................................ 05

Sharp ............................... 06, 07

Sony ...................................... 08

Toshiba ................................. 09

Sanyo .................................... 10

Fisher .................................... 10

Cable Box Brand Code Numbers

Archer ......................... 44, 06, 01, 120, 05, 63, 126

Cableview ................ 29, 09, 01, 63, 120, 44, 42, 30

52, 04, 124, 126

Citizen ................... 44, 52, 30, 63, 42, 04, 124, 126

Curtis ..................................... 08, 09, 25, 61, 53, 87

Century ...................................... 44, 51, 75, 59, 126

Cabletenna .................. 29, 09, 01, 63, 120, 44, 126

Cable Cinema .............. 29, 09, 01, 63, 120, 44, 126

Diamond ...................... 29, 09, 01, 63, 120, 44, 126

Eagle ....................... 62, 40, 22, 13, 58, 20, 26, 107

Eastern ................................................... 28, 29, 130

Explorer .................................. 08, 09, 25, 61, 53, 87

Gemini ..................................................... 30, 04, 124

General Electric ...................................... 01, 57, 120

General Instruments . 01, 84, 83, 34, 03, 02, 04, 55 65, 66, 67, 68, 120, 106, 121, 122, 115, 117, 118, 124

Gerrard ............................................... 44, 51, 75, 59

GC Electronics ............... 44, 42, 63, 29, 30, 52, 04

124, 126

Hamlin ............... 41, 14, 15, 28, 102, 104, 103, 130

Hitachi ................................................................... 31

Jerrold .......... 01, 84, 83, 34, 03, 02, 04, 55, 65, 66

67, 68, 120, 106, 121, 122, 115, 117, 118, 124

Jasco ...................................................... 30, 04, 124

Macom ................................................................... 31

Magnavox ...................................................... 26, 112

Matsushita ................................. 17, 16, 08, 87, 109

Movietime ...................... 32, 39, 42, 44, 126, 38, 40

Maestro ........................................................... 74, 35

NEC .................................................... 40, 19, 38, 32

NSC .................................................... 40, 19, 38, 32

Novavision ............................. 08, 09, 25, 61, 53, 87

Next Level ...........01, 84, 83, 34, 03, 02, 04, 55, 65

66, 67, 68, 120, 106, 121, 122

Oak................................................. 46, 11, 129, 101

DSS Brand Code Numbers

Toshiba ....................................................... 90

Hitachi/ Hughes.................................... 91, 99

Primestar .................................................... 92

Drake .......................................................... 93

Magnavox ............................................. 94, 95

Uniden ................................................... 94, 95

JVC........................................ 11

Hitachi ................................... 12

Mitsubishi ........................ 07, 13

Samsung ............................... 14

Gold Star ................... 15, 16, 17

Oak Sigma ..................................... 46, 11, 129, 101

Panasonic .................................. 17, 16, 08, 87, 109

Philips ................... 23, 24, 20, 13, 07, 50, 128, 129

Pioneer ...................................................... 06, 05, 12

Pulsar .................... 04, 42, 63, 44, 30, 52, 124, 126

Quest ........................................................ 06, 05, 12

Radio Shack ............................... 44, 51, 75, 59, 126

RCA ............................................ 17, 16, 08, 87, 109

Realistic ..................................... 44, 51, 75, 59, 126

Recoton ...................................... 44, 51, 75, 59, 126

Regal ................. 41, 14, 15, 28, 102, 104, 103, 130

Regency .................................................. 28, 29, 130

Rembrandt ....... 44, 42, 63, 29, 01, 32, 39, 120, 126

Samsung ...................................... 42, 06, 32, 05, 40

Scientific Atlanta ................... 08, 09, 25, 61, 53, 87

Sheritech ............................................................... 27

Signal ............................................................ 26, 112

SL Marx ............. 42, 06, 32, 40, 43, 44, 52, 63, 126

Sprucer ...................................... 17, 16, 08, 87, 109

Standard Components ............... 32, 39, 42, 44, 126

Stargate .............. 04, 42, 32, 40, 63, 44, 30, 52, 06

124, 126

Sylvania .......................................................... 19, 18

Teknika ........................................................... 74, 35

Telecaption .................................................... 77, 127

Teleview ................................. 40, 19, 38, 32, 42, 06

Texscan .......................................................... 19, 18

Tocom ................................... 34, 33, 01, 42, 66, 120

Toshiba ................................................................. 36

Unika ........................... 44, 42, 63, 29, 01, 126, 120

Universal .............................. 52, 43, 44, 63, 42, 126

Viewstar .................. 62, 40, 22, 13, 58, 20, 26, 107

Videoway .......................................... 07, 23, 50, 129

Vidtek .................................................................... 64

Zenith ............................................... 07, 23, 50, 129

Optimus ................................................ 94, 95

Panasonic ................................................... 96

ProScan ...................................................... 97

RCA ............................................................. 97

SONY .................................................. 98, 105

Operation

VCR

Important Notes

• Due to changes in infra-red commands used by manufacturers, some brands have several codes. If your unit does not respond to the first code, please try the next one.

• Some TV, Cable Box and DSS Receiver brands require you to turn on the power manually.

Page 30

Tape Operation

Search System

For each recording, an invisible index mark is placed on the tape. A program index and information are also included for timer recordings. These marks are used to access or scan recordings.

Index Search

Program End Search

INDEX SEARCH

ENTER INDEX NUMBER :1 USING 1- 9 KEYS

FORWARD SEARCH :FF REVERSE SEARCH :REW NEXT :SEARCH EXIT :STOP

Press SEARCH*

to display SEARCH in Stop or Play mode, and then

press NUMBER keys

to select recording number.

• To calculate number, see below.

Press FF/SLOW+

or REW/SLOW- on the remote to start search.

INDEX SEARCH

Play begins at search end. To search forward

FORWARD SEARCH : FF REVERSE

SEARCH : REW

or back 1 index,

press FF/SLOW+ or REW/SLOW- on the

remote while screen left is displayed (10 sec.).

• To cancel, press PLAY or STOP.

To Calculate Index Number

Example 1:

To go to rec. 2 from rec. 4, enter 3 and press REW.

61572 34

Locates end point of recording for continuity.

Press SEARCH twice to display SEARCH in Stop or Play

mode.

PROGRAM END SEARCH

Press FF/SLOW+

on the remote to start PROGRAM

SEARCH START : FF

EXIT

:SEARCH

END SEARCH.

• To cancel, press PLAY or STOP.

Examples of Program End Search. Fig. 1

Program 1

the current tape position Press SEARCH button

INDEX

Program 2 or BLANK

End Point

Fig. 2

INDEX

Program 1

Fig. 3

INDEX

Program 1

End Point

the current tape position Press SEARCH button

BLANK

INDEX

Program 2

If search exceeds

a few seconds in BLANK area.

BLANK

End Point

Program 2

Example 2:

To go to rec. 6 from rec. 2, enter 4 and press FF.

17534 62

NOTE: indicates start points of each recording.

Note

• If Index Search is started very close to an index mark, that index mark may not be counted in the search.

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : consumerproducts@panasonic.com

Upon locating end point,

➛➛

➛ search continues 7 sec. past end point,

➛➛

➛ tape rewinds to 10 sec. before end point,

➛➛

➛ tape plays to end point and stops.

➛➛

Note

• If Program End Search is started very close to an index mark, that mark may be skipped over.

Page 31

PLAY

1st Press

2nd Press

3rd Press

1 min Skip

2 min Skip

3 min Skip

*Important: If a remote control button does not work when pressed,

press the VCR button on the remote and try the button again.

Auto Operation Functions

Auto Play

Insert a tape ➛ Power comes on, ➛ Play starts if no record tab

(see p. 6).

Auto Rewind

REW/SLOW-

PLAY

FF/SLOW+

STOP

Play Fast Forward

Play Auto Eject

(Repeat Play must be off)

➛ ➛

➛ Tape end

Play

➛ ➛

➛ Tape ejects if no record tab

➛ ➛

➛ Tape end ➛ Rewind

➛ ➛

➛ Rewind

➛ ➛

NUMBER keys

CM/ZERO

Operation

VCR

Commercial Skip

VCR fast forwards (skips) over 1~3 minutes of recorded tape.

Press CM/ZERO in Play mode.

• The skip time can be changed by pressing CM/ZERO repeatedly as shown by the figure below.

• No indication appears on-screen.

Page 32

Tape Operation (continued)

REPEAT

Repeat Play

Set to playback a recording over and over.

Press ACTION*

to display MENU.

SET UP VCR

SET CLOCK

SET UP CHANNEL IDIOMA/LANGUE : ENGLISH VCR’S OUTPUT CH:3

SELECT :

: ACTION

SET

UP VCR

PLAY : O

ARN I NG

SHU

T-OFF

: O

CT :

: ACT I ON

SET : SET

: O

EXIT

REPEAT

REMOTE W

AUTO

SELE END

• Play repeats at tape end or if unrecorded portion over 30 sec. is detected.

Press

to select “SET UP VCR,” and

press SET.

Press

to select “REPEAT PLAY,”

and press SET to set “ON” or “OFF.”

SET: SET

Press ACTION twice to return to normal screen.

Note

• For repeat play in DVD mode, see page 42.

Zero Search

To quickly return to a specified tape location.

Press DISPLAY during play

to display Counter.

PLAY

1 2 : 0 0A

Press COUNTER RESET

0 : 0 0 : 0 0

at desired position to reset to “0:00:00”.

DISPLAY

STOP

ACTION

SELECT

SET

CM/ZERO

COUNTER RESET

Continue to record, playback etc.

Press STOP.

REW

1 2 : 3 0A

M CH 02

STOP

1 2 : 3 1AM CH 02

• DECK will go into FF or REW mode and stop at the last point the Counter was set to 0:00:00.

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : consumerproducts@panasonic.com

Press CM/ZERO in Stop

0 : 30 : 30

mode to start Zero Search.

0 : 0 0 : 0 0

Page 33

Special VCR Features

Weak Signal Display Feature

When “ON,” picture is displayed regardless of signal strength.

Press ACTION

to display MENU.

MENU SET UP VCR SET CLOCK

SET UP CHANNEL

IDIOMA/LANGUE : ENGLISH VCR’S OUTPUT CH:3

SELECT :

ACTION

SELECT

SET

VCR Lock Feature

When set to ON, all operations except for timer record and tape eject are prohibited. Useful for households with small children.

To turn on, hold down REC on DECK in Stop mode with no tape inserted for 7 seconds.

(Please ignore “NO CASSETTE” warning.)

VCR LOCK ACT I VA

To turn off, repeat above.

VCR LOCK OFF

• VCR Lock cancels in 24 hours if clock is set.

TED

• ON: Picture is displayed regardless of signal

OFF: Screen turns solid blue when signal is weak or

• Selecting ON has no effect on connected equipment with blue back feature.

Auto Shut-Off Feature

The power shuts off at a preset time.

1 2

EXIT

: ACTION

SET UP CHA

ANT

ENNA

: CABLE

UTO SE

WEAK

S I GNAL D I

SELECT : EXIT

: ACT I ON

condition, and may not always be clearly visible.

non-existent.

Press ACTION twice to return to normal screen.

Press ACTION

to display MENU.

SET UP VCR

SET CLOCK SET UP CHANNEL IDIOMA/LANGUE : ENGLISH VCR’S OUTPUT CH:3

SELECT : EXIT

: ACTION

SET

UP V REPEAT PLAY : O REMOTE W

ARN I NG

AUTO

SHUT-

CT :

SELE EXIT

: ACT I ON

*Important: If a remote control button does not work

when pressed, press the VCR button on the remote and try the button again.

Press

to select “SET UP CHANNEL,” and

SET : SET

NNE

SPLAY:OFF

press SET.

Press

to select “WEAK SIGNAL DISPLAY,” and

press SET

SET: SET

to set “ON” or “OFF.”

Press

to select “SET UP VCR,” and

press SET.

SET : SET

Press

FF N

to select “AUTO SHUT-OFF.”

Press SET repeatedly to change shutoff time as

SET: SET

shown below.

OFF

2 Hours

6 Hours

OFF

: O

Operation

VCR

4 Hours

REC

Press ACTION twice

to return to normal screen.

Note

• The shut-off countdown will not function during Play or Record.

Page 34

Special VCR Features (continued)

Remote Warning Feature

*Important: If a remote control button does not work

If Multi-brand feature is used (p. 28), and this feature is set to on, a warning appears whenever an invalid key is pressed in TV, DSS or CABLE mode.

Press ACTION*

to display MENU.

SET UP VCR

SET CLOCK

SET UP CHANNEL IDIOMA/LANGUE : ENGLISH VCR’S OUTPUT CH:3

SELECT : EXIT

: ACTION

REPEAT PLAY : O

REMOTE W

AUTO

SHUT-

CT :

SELE EXIT

: ACT I ON

SET

ARN I NG

UP V

OFF

: O

SET : SET

: O

SET: SET

Press

to select “SET UP VCR,” and

press SET.

Press

to select

“REMOTE WARNING,” and

press SET to set “ON” or “OFF.”

• If “OFF,” remote warning will not appear when invalid key is pressed.

Press ACTION twice to return to normal screen.

Tape Position and Tape Status Feature

To find out the present tape position and amount of tape remaining.

Tape position is displayed for VHS-C Cassettes type, tapes under 30 minutes, and some other tapes, but the position is not correct.

Press TAPE POSITION

to detect current tape position.

DETECTING TAPE POSITION

R 120 M

BEG I

N END

•“DETECTING TAPE POSITION” is displayed only when a cassette is first inserted, and it takes several seconds for correct tape position to appear.

• The present tape position indication and amount of tape remaining (according to tape speed) is displayed.

• Tape remaining time display may not be precise.

when pressed, press the VCR button on the remote and try the button again.

INPUT

STOP

PAUSE/ STILL

ACTION

SELECT

SET

TAPE POSITION

REC

Press TAPE POSITION

to return to normal screen.

Note

This function cannot display exact amount of tape remaining for tapes 30 minutes or less, or for tapes over 120 minutes in length.

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : consumerproducts@panasonic.com

Page 35

Copying Your Tapes (Dubbing)

Connection

VCR/ Camcorder (Hi-Fi)

VIDEO

AUDIO

OUT

Connect VIDEO OUT terminal on Playing VCR to VIDEO IN terminal on DECK. To monitor the dubbing, also connect TV as shown.

Connect “L” and “R” AUDIO OUT terminals on Playing VCR to “L” and “R” AUDIO IN terminals on DECK.

In place of Playing VCR, you can use other equipment, such as a Camcorder. Simply connect the unit’s Audio/Video outputs to DECK.

DVD/VCR DECK

VIDEO

AUDIO

OUT

IN FROM ANT.

IN 1

VHF/UHF

OUT TO TV

Playing (Source) VCR Recording (Editing) DECK

VHF/

UHF

Front of DECK

VIDEO IN 2

(Audio/Video In Terminals on the front of DECK are available)

L-AUDIO IN2-R

Insert a pre-recorded tape.

Insert a blank tape with record tab.

Press INPUT to set DECK Input mode to

Press PLAY, then PAUSE/STILL

immediately to enter PLAY/PAUSE mode.

The operation of steps 4 and 5 must be done on both playing and recording VCRs at the same time.

Press PLAY to start dubbing.

Playing VCR starts playback.

Press STOP to stop dubbing.

LINE for Video Input.

(See “Selecting the Input Mode” below.)

Press REC, then PAUSE/STILL immediately to enter REC/PAUSE mode.

Press PAUSE/STILL to start dubbing. DECK starts recording.

Press STOP to stop dubbing.

To Monitor Dubbing on TV

1 Turn TV on and tune to the Recording

VCR channel (CH 3 or CH 4).

2 Set the VCR/TV Selector on DECK to

“VCR.”

Note

Caution:• Unauthorized exchanging and/or copying of copyrighted recordings may be

• Dubbing tapes protected with Copy Guard will have poor quality results.

• Please note that some tapes cannot be dubbed on DECK. Also, it is not possible to dub DVD/ Video CD/ CD to VHS tapes using DECK.

Selecting the Input Mode

Method 1: Press INPUT repeatedly.

Method 2: Press CH / .

Press

•“L1” or “L2” lights up on Multi Function Display (about 4 seconds) when LINE1 or LINE2 is selected.

• LINE1: For rear audio/video connection. LINE2: For front audio/video connection.

Channel Number

Display will change as below.

LINE1

LINE2

(CABLE)

125

↔↔

↔ LINE1

↔↔

(TV)

↔↔

↔ LINE2

↔↔

Press

Operation

VCR

Page 36

3 ESP

SELECT

SET

1 ENG

SELECT

SET

ESP

Te amo

ENG

FRA

DEU

ITA

ESP

NLD

English French German Italian Spanish Dutch

SVE

NOR

DAN

POR

RUS

JPN

Swedish Norwegian Danish Portuguese Russian Japanese

CHI

KOR

MAL

VIE

THA

∗

Chinese Korean Malay Vietnamese Thai Other

Disc Operation

Subtitle Language (DVD only)

You can select a different subtitle language (if offered) than the one set at the Settings for DVD Operation. (See p. 45.)

Press

in Play mode to display the subtitle selection on-screen.

SUB TITLE

• Display disappears after 5 seconds.

• When no subtitles are offered, “-” will be displayed instead of the language number.

ESP

Press

to select a language.

Press

(or )

to set.

Te amo

Press

to select “ON” or “OFF.”

Number of subtitle language being played back.

Notes

• If after several presses of the button the language does not change, language selection is not offered on the disc.

• When power is turned on again or disc is removed, subtitles revert to initial setting language. If the initial language is not recorded on the disc, the disc’s priority language will appear.

Ready Checklist

Please read “Basic DVD Operation” on p. 22.

[Subtitle language (No.)] [Audio sound track language (No.)]

Audio Soundtrack Language (DVD only)

You can change the audio soundtrack language, selected at the Settings for DVD Operation, to a different language if available. (See p. 45.) (This operation works only with discs on which multiple audio soundtrack languages are recorded.)

Press

AUDI O: 1 ENG

Number of the audio soundtrack language being played back.

Dolby Digital 3/2.1ch

Hello

SELECT

: SESET:T:SET

AUDI O: 3 ESP

Dolby Digital 3/2.1ch

Hola

SELECT

: SESET:T:SET

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : consumerproducts@panasonic.com

AUDIO

in Play mode to display the audio selection on-screen.

• Display disappears after 5 seconds.

Audio attribute 1 type, sampling frequency, bit No. of the disc.

Press

to select desired language.

• Change the No. by pressing , and press

SET

[Audio attribute 1 type, sampling frequency, bit No. of the disc (see p. 46.)]

LPCM

Dolby Digital

DTS

96KHz

48KHz

1ch - 5.1ch 1ch - 5.1ch

Linear PCM disc

20bit 24bit

Dolby Digital disc DTS disc

16bit

Notes

• If, after several presses of the

AUDIO button the language does not change, language selection is not offered on the disc.

• When power is turned on again or

disc is removed, language reverts to initial setting. If this language is not recorded on the disc, the language recorded will be heard.

Page 37

• DVD Karaoke (1 vocal) VOCAL ON VOCAL OFF

• DVD Karaoke (2 vocals) VOCAL V1 + V2 VOCAL V1 VOCAL V2 VOCAL OFF

• Video CD LR L R

VOCAL ON

Important: if a remote control button does not work when pressed,

press the DVD button on the remote and try the button again.

When appears on the screen while a button is being operated, it means that the corresponding operation is prohibited by DECK or the disc.

Multiple Angle Viewing (DVD only)

DVDs may contain scenes shot from multiple camera angles allowing the same scene to be viewed at different angles. You can view these angles, if available, using the ANGLE button.

ANGLE Indicator

Notes

• The ANGLE Indicator lights up on DECK when a scene recorded at different angles is detected.

• The angle number can be set beforehand so that the angle is switched whenever the ANGLE Indicator lights up.

Number of angle being played back.

Vocal Selection for Karaoke Discs

SET

SELECT

SUB TITLE ZOOM

ANGLE AUDIO

Notes

• The subtitle cannot be enlarged nor

can it’s position be changed.

• The picture zoom feature does not

work with a Video CD.

• During picture zoom, “ZOOM1” or

“ZOOM2” is displayed on-screen.

• Zooming, on some discs, may result

in poor picture quality, or may not operate at all.

Picture Zoom (DVD only)

You can enlarge specific portions of a picture and select the zoom ratio using the ZOOM button during DVD playback.

Press

as follows.

• You can enlarge the center portion of the image to one of 2 magnifications.

■ Use the , , and buttons to move the position

up, down, left and right.

ANGLE : 1

SELECT : SET:SET

Press

AUDIO

to display the audio screen.

AUDIO:2 ENG VOCAL ON

SELECT : SET: SET

ZOOM

repeatedly to change display

Press

in Play mode to display the angle selection on-screen.

• Display disappears after 5 seconds.

Press

to select the desired angle.

in Play mode

Press (or ) to select as shown below, and press (DVD only)

ANGLE

(DVD/Video CD)

(or ) to set.

Operation

DVD

Page 38

Disc Operation (continued)

Title Menu (DVD only)

Some DVDs have more than one title, e.g. movies. If the disc offers a title menu, you can select the desired title number. (Operation may vary according to the disc.)

Press

TITLE

T I TLE MENU

Dogs

Love

Cas t l es

in Play mode to display the title screen.

i r

T I TLE MENU

Cas t l es

Dogs

Love

B i rds

of the world

i r

Press or

NUMBER keys

to select a title, and

press

to start playing.

•“Pressing not necessary when using

NUMBER keys.

SET

PLAY

” is

DVD Menu (DVD only)

DVDs may offer a special menu. This menu may include guides to unique contents, audio/subtitle languages, etc. Although contents and operation may vary, the following steps show basic steps for using the menu.

Press

DVD MENU

1 . SUBT I TLE

2 . AUD

3 . ANGLE

DVD MENU

1 . SUBT I TLE

2 . AUD

3 . ANGLE

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : consumerproducts@panasonic.com

in Play mode to display DVD MENU.

Press or

NUMBER keys

to select an item, and

press

SET

PLAY

to perform.

•“Pressing not necessary when using

NUMBER keys.

Repeat step 2 if there is more than one menu.

SET

PLAY

” is

PLAY

STOP

NUMBER keys

CLEAR ACTION

SELECT

SET

TITLE

Page 39

PLAY MODE

PROGRAM PLAY

DISC REPEAT

REPEAT OFF

TRACK

Important: if a remote control button does not work when pressed,

press the DVD button on the remote and try the button again.

Program Play (Video CD/CD)

You can program specific tracks and order of play.

Press

ACTION

to display MENU.

DVD MAIN MENU

DI SC LANGUAGES AUDIO OUTPUT ST IL L MODE : F I EL D TV MODE : Le t te r box 4:3 PARENTAL LOCK :

PLAY MODE

SELECT : SET : SET END : ACTI ON

PROGRAM PLAY

RANDOM PLAY

LEVEL 8

PLAY MODE

Press

to select “PLAY MODE,” and

press

SET

to display.

Press

to select “PROGRAM PLAY,” and

SELECT : SET : SET END : ACTI ON

PROGRAM PLAY

DI SC PROGRAM

1 61116 5 8

2 7 12 17 15 6 3 8 13 18 1 13 4 9 14 19 3 2 5101520 2

CLEAR LAST

CLEAR ALL START SELECT : SET : SET END : ACTI ON

• Repeat step 4 to select another track.

• The selected track is added on the right side.

PROGRAM PLAY

DI SC PROGRAM

1 61116 5 8

2 7 12 17 15 6 3 8 13 18 1 13 4 91419 32 5101520 2

CLEAR LAST

CLEAR ALL START SELECT : SET : SET END : ACTI ON

press

SET

to display.

Press

to select a track number (Track numbers on disc are displayed.), and

press

SET

Press

to select “START,” and

press

SET

to start play of programs in the sequence selected.

• To cancel, press during play, then press

CLEAR

STOP

Ready Checklist

DECK is in DVD mode, press DVD. Video CD or CD is inserted.

Program Repeat Play (Video CD/CD)

Do operation steps 1 through 5

at left on this page.

Press

DISPLAY

Information screen.

(Disc Information Screen)

TRACK

: 1 V IDEO CD

PBC : OFF 1 : 35: 12

SET : SET NEXT : DISPLAY

Press

DISPLAY

DECK Information screen.

Press

SET

“REPEAT OFF” will flash.

(DECK Information Screen)

PLAY

REPEAT OFF

PROGRAM PLAY

SET : SET END : DI SPLAY

Press to select “DISC

REPEAT.”

(DECK Information Screen)

PLAY

DISC REPEAT

PROGRAM PLAY

to display Disc

to display

to enter Select mode.

Operation

DVD

Notes

• Up to 15 tracks can be programmed.

•“ ” or “ ” (depending on disc) indicates additional

PROGRAM PLAY screen. Press for next or previous screen.

• To clear the last program one by one

Press to move to “CLEAR LAST” and press

SET

also clears last program.)

• To clear all programs

Press to move to “CLEAR ALL” and press

SET.

is turned off or the disc is removed.)

. (Pressing

(Programs are also cleared when the power

CLEAR

on remote control

SELECT : SET : SET END : DISPLAY

Press

SET

REPEAT” will stop flashing.)

to set mode. (“DISC

To cancel, select “REPEAT OFF” in step 5, then press

SET

Page 40

Disc Operation (continued)

PLAY MODE

Random Play (Video CD/CD)

Tracks are played in a random order.

Press

to display MENU.

ACTION

Ready Checklist

DECK is in DVD mode, press DVD.

*Important: If a remote control button does not work when pressed, press the DVD button on the remote and try

DVD MAI N MENU

DI SC LANGUAGES

AUDIO OUTPUT ST IL L MODE : F I E LD TV MODE : L et t er b ox 4: 3 PARENTAL LOCK :

PLAY MODE

SELECT : SET : SET END : ACT ION

PROGRAM PLAY

RANDOM PLAY

LEVEL 8

PLAY MODE

Press

to select “PLAY MODE,” and

press

SET

to display.

Press

to select

the button again.

“RANDOM PLAY,” and

press

SELECT : SET : SET END : ACT ION

SET

to begin random play.

• To cancel, press during play, then press

CLEAR

STOP

Setting the Sound Output Level

Audio recorded on a DVD or Video CD often incorporates a dynamic range of sound. This means that, when compared to a music CD, etc., the average volume is generally lower and the peaks may be higher. This unit can be set so that the average volume is increased automatically.

Press

AUDIO CONTROL

•“ON” or “OFF” lights up on Multi Function Display (about 3 seconds) when press AUDIO CONTROL.

repeatedly to change “ON”

↔↔

↔ “OFF.”

↔↔

STOP

CLEAR ACTION

SELECT

SET AUDIO

CONTROL

DVD /Video CD

Audio Control “OFF”

Volume level is low.

Audio Control “ON”

Volume level is increased

automatically when played back.

Music CD

•“ON” is set ..... When a DVD or Video CD is played back, the average volume is increased.

•“OFF” is set .... The volume level recorded on the disc is played back just as it is.

Notes

• When audio equipment is connected, setting the Sound Output level to “OFF” is recommended.

• If the sound becomes abnormal while playing a disc, set the Sound Output level to “OFF.”

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : consumerproducts@panasonic.com

Page 41

TRACK

CHAPTER

DVD Operation using On-Screen Displays

TRACK

When

DISPLAY

disc information (title/chapter/track number, elapsed playing time) and DECK information (repeat play, play mode).

Press

to display “On-Screen Displays.”

• Each press of

display as follows. (refer to p. 42.)

is pressed, On-Screen Displays show

DISPLAY

in Play or Stop mode

DISPLAY

changes the on-screen

Selected disc information

Ready Checklist

DECK is in DVD mode, press DVD.

Note

DISPLAY

TITLE MENU is displayed.

button does not function while DVD

Press (or )

to select

press

an item, and

SET

Press

to select the setting, and

press

SET

T ITLE : 12 DVD

CHAPTER

: 11

T ITLE : 12 DVD

CHAPTER

: 24 0:12:34

SELECT : SET : SET NEXT : DI SPLAY

TRACK

: 12

PBC : OFF 0 : 12 :34

TRACK

: 17

PBC : OFF 0 : 12 :34

SET : SET NEXT : DI SPLAY

Selected DECK information

Normal Screen

0:12:34

• For some functions the setting will be registered immediately without pressing

• When numbers are displayed (e.g. title number), are also available.

To make corrections, press

repeatedly to move to the error, then correct.

• Pressing is effective for elapsing time

VI DEO CD

instead of the above buttons. Press repeatedly to delete the error, then correct.

To return to normal screen, press

DISPLAY

SET

NUMBER keys

and

CLEAR

repeatedly.

SET

DISPLAY

NUMBER keys

CLEAR

SELECT

SET

Notes

• When

• When appears on the screen

DISPLAY

pressed during playback of a Video CD with Playback control,

NUMBER keys

on the displayed screen. In this case, press remove the displayed screen.

while a button is being operated, it means that the corresponding operation is prohibited by DECK or the disc.

button is

are not available

DISPLAY

again to

Operation

DVD

Page 42

DVD Operation using On-Screen Displays (continued)

SELECT : SET : SET NEXT : DISPLAY

TITLE : 1 DVD

CHAPTER : 12 1 : 12: 55

SET : SET NEXT : DISPLAY

TRACKTRACK : 1 VI DEO CD

PBC : OFF 1 : 35: 12

SELECT : SET : SET END : DISPLAY

PLAY

CHAPTER REPEAT

SET : SET END : DI SPLAY

PLAY

DISC REPEAT

RANDOM PLAY

Detailed Descriptions of each On-Screen Display

■■

■ Disc information screen (for DVD)

■■

1. TITLE No.

• Change the No. by pressing * or

2. Chapter No.

• Change the No. by pressing or

3. Disc currently being played

4. Elapsed playing time

The screen may be changed by selecting the elapsed time.

• Change the elapsed time by pressing e.g., press 0 - 1 - 2 - 3 - 4 - 5 for 01 : 23 : 45.

• This function does not work with some discs.

■■

■ Disc information screen (for Video CD/ CD)

■■

A.Track No.

• Change the No. by pressing or

B.Playback control ON/OFF

[Video CD with playback control only]

ON Video CD menu play is displayed. OFF Video CD menu play is cleared.

C.Disc currently being played

Video CD CD

D.Elapsed playing time

Note

• Track No. and the elapsed playing time are not displayed during play started from menu of Video CDs with playback control.

• When appears on the screen while a button is being operated, it means that the corresponding operation is prohibited by DECK or the disc.

■■

■ DECK information screen (for DECK)

■■

• Change the desired mode during play by pressing , and press

a. Repeat Play

DVD CHAPTER REPEAT TITLE REPEAT REPEAT OFF Video CD/CD TRACK REPEAT DISC REPEAT REPEAT OFF

b. Play mode [Video CD/ CD only] (See p. 39 or 40.)

PROGRAM PLAY program play RANDOM PLAY random play

----

normal play

NUMBER keys

, and press

SET

1 2

A B

3 4

C D

For your reference

•

CHAPTER/TITLE REPEAT PLAY (DVD)

CURRENT PLAYBACK POSITION

TITLE

chapter

CHAPTER REPEAT

TITLE REPEAT

NORMAL PLAY

Note

• For repeat play in VCR mode, see p. 32.

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : consumerproducts@panasonic.com

chapter

•

TRACK/DISC REPEAT PLAY (Video CD/CD)

CURRENT PLAYBACK POSITION

track

TRACK REPEAT

DISK REPEAT

NORMAL PLAY

track

Page 43

MP3 Playback Operation

MP3 Playback

You can use this unit to play MP3 format audio recorded for personal use with a computer etc. onto a CD-R or CD-RW. Play may not be possible in some cases due to the condition of the recording.

Press

1 2

POWER

Press

OPEN/CLOSE

and then place a MP3 disc into the disc tray.

Press

OPEN/CLOSE

MP3 MENU is displayed and playback is started automatically.

displayed.)

Function

Status

Folder area

(The currently

displayed folder

turns green)

ROOT

END_W DD_CUB I C N

CTURNE

TECHNO

POPS

AZZ

■ Forward/Reverse Search Press

FF/SLOW+

Press

PLAY

• Search speed, slow at first, increases with each

additional press of the button up to 4 levels.

■ Forward/Reverse Track Skip Press

SKIP

Each press skips a track.

• If pressed within first 3 seconds of playback, skips

to the previous track. If over 3 seconds, returns to first of that track. (|

• Only the

for track skip selection during playback. Place unit into Stop mode before performing folder/ file selection (see above right.)

SKIP

on the remote or DECK.

to close.

(The MP3 CD directory is

PLAY

MP3

ROOT . .

END_W

TECHNO

POPS

NOCTURNE

AZZ

NORN

PLAY MODE : NORMAL

PLAY MODE

ALTZ

(The MP3 CD directory structure displayed in the above example OSD is shown in the diagram at left.)

REW/SLOW-

to release.

| or |

DD_

SKIP

00 : 00 :

ALTZ

CUB I C

during play.

only.)

button can be used

Counter

Parent

folder

File area

(The selected MP3 file/folder is displayed with a cursor.)

: MP3 file : Folder : Parent folder

during play.

*Important: If a remote control button does not work

when pressed, press the DVD button on the remote and try the button again.

■ MP3 playback (During STOP mode)

1) Press

2) Press

to select an MP3 file ( ).

SET

PLAY

to start playback.

■ Select folder (During STOP mode)

1) Press

2) Press

to select a folder ( ).

SET

to display files/folders

contained in the folder.

■ Select parent folder (During STOP mode)

1) Press

2) Press

to select a folder ( ).

SET

to make changes to

the previous directory display.

Note

• Folder area operation cannot be done. Only file area operation is possible.

■ Select PLAY MODE (During STOP mode)

1) Press

to move cursor to

PLAY MODE.

2) Press to select the desired

PLAY MODE (see below).

[PLAY MODE]

NORMAL:

All MP3 files are selected and played back one time only.

Operation

SINGLE REPEAT:

The selected MP3 file is played back repeatedly.

FOLDER REPEAT:

The MP3 files contained in the selected folder are played back repeatedly. However, folders below the selected folder are not played back.

DISC REPEAT:

All MP3 files are played back repeatedly.

DVD

Press

STOP

Press

The MP3 MENU is closed automatically.

to stop playing.

OPEN/CLOSE

to eject the disc.

Page 44

DVD Lock Feature

*Important: If a remote control button does not work when

pressed, press the DVD button on the remote and try the button again.

You can prevent playback of DVDs of a specific rating level which may be unsuitable for children.

• Some DVDs are encoded with a rating level. If the disc rating is higher (stricter) than the one you preset, playback will be prohibited.

DVD Lock (DVD only)

A 4-digit code must be entered to view a blocked program or change rating settings.

Press

ACTION

to display MENU.

DVD MAIN MENU

DI SC LANGUAGES AUDIO OUTPUT

ST IL L MODE : FIELD TV MODE : Letterbox 4:3

PARENTAL LOCK : LEVEL 8

SELECT : SET : SET END : ACTI ON

ENTER 4-D I G I T

END

: ACT I O

ENTER : 0

----

To Make Corrections

Press repeatedly to

move the cursor.

Press

NUMBER keys

make the correction.

LEVEL 0 : LOCK ALL, Playback of all DVDs, CDs and

LEVEL 1 : mature theme DVDs LEVEL 2 : DVDs expressly for children can be played back. LEVEL 3 to 7 : DVDs for general audiences/children can be

LEVEL 8 : NO LIMIT: (Factory preset)

Video CDs is prohibited. (Use to prohibit play of mature theme DVDs not encoded with rating level.)

All DVDs can be played back.

Press

to select “PARENTAL LOCK,” and

press

SET

to display.

1) Press

CODE

2) Enter same secret code

3) Press

• Step 2) not necessary when changing rating or secret code.

• Take care that you are not

observed entering the secret code.

NUMBER keys

to enter your secret code.

again for confirmation.

SET

to display.

Press

to select rating level, and

press

SET

to select “LOCKED” or “UNLOCKED.”

played back. (DVDs with mature content are prohibited.)

Ready Checklist

DECK is in DVD mode, press DVD.

Caution

Discs not encoded with rating level will play even if the jacket states it is for mature audiences. For these discs, the DVD Lock Ratings will not work.

YOUR SELECTI ON EXCEEDS THE

PLAYER S RATI NG LIMIT. DO YOU WANT TO CHANGE THE LIMIT?

YES

SELECT: SET : SET END : DISPLAY

After DVD Lock is set and a blocked DVD is played, this message will appear. The message may differ depending on the disc.

To continue viewing a blocked program for now, Press to select “YES” and

SET. Then, enter your 4 digit secret code. When “NO” is selected, blocked programs cannot be viewed.

Change your secret code

• You will need your current code. Do step 1 ~ 2 left. Enter current secret code.

Press

CLEAR

Do step 4 to enter new code.

to clear the code.

Press

to end setup.

ACTION

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : consumerproducts@panasonic.com

twice

Note

• DO NOT forget your secret code.

Page 45

Settings for DVD Operation

Press

ACTION

to display MENU.

DVD MAIN MENU

DISC LANGUAGES

AUDIO OUTPUT

ST IL L MODE : TV MODE : Letterbox 4:3 PARENTAL LOCK :

SELECT : SET : SET END : ACTI ON

AUTO

LEVEL 8

Press

to select an item, and

press

SET

DISC LANGUAGES (See below)

All languages offered on the disc can be set. If the language not offered is set, the original disc language will be selected.

AUDIO OUTPUT (See p. 46.)

You can set the audio output that comes from the digital audio output terminal.

STILL MODE (See p. 47.)

To select “FIELD” (Field still) or “FRAME” (Frame still) to prevent jitter or make small text or fine patterns clearly visible in a still picture. When “AUTO” is set “FIELD” or “FRAME” is selected automatically.

TV MODE (See p. 47.)

To select whether the video material for a widescreen will be played back in the Pan & Scan style, Letterbox style or 16 : 9 style.

Disc Languages (DVD only)

To select and set the language of the audio soundtrack, subtitles, or title/DVD menus for all discs to be played.

DVD MAIN MENU

DISC LANGUAGES

AUDIO OUTPUT

ST IL L MODE : TV MODE : Letterbox 4:3 PARENTAL LOCK :

SELECT : SET : SET END : ACTI ON

AUDIO : English

SUBT ITLE : AUTO

MENUS : English

SELECT : SET : SET END : ACTI ON

Press

and go to step 2 to setup another item.

Or, press

AUTO

LEVEL 8

DI SC LANGUAGES

ACTION

Press

to select “DISC LANGUAGES,” and

press

SET

to display screen.

Press

to select an item, and

press

SET

repeatedly for desired language. (Please refer right.)

to redisplay DVD menu

twice to exit.

Once initial settings are done, they remain in memory (even after power off) until changed. This means DECK will operate under the same conditions (especially DVDs) each time.

Ready Checklist

DECK is in DVD mode, press DVD.

NUMBER keys

CLEAR ACTION

SELECT

SET

“AUDIO” selections

(Factory preset: English)

To select the audio soundtrack language.

English/Spanish/French/Japanese Original: Original disc language

OTHER ✱✱✱✱: Other language selection*

“SUBTITLE” selections

(Factory preset: AUTO)

To select the subtitle language.

AUTO: Same language selected

for “AUDIO”

• If language set for “AUDIO” is used in playback, subtitles will not appear.

• If another language is used during playback, the subtitles will appear in the language selected at “AUDIO” setup.

English/Spanish/French/Japanese OTHER ✱✱✱✱: Other language selection*

“MENUS” selections

(factory preset: English) To select the language used in title menus or DVD menus.

English/Spanish/French/Japanese OTHER ✱✱✱✱:

To enter OTHER ✱✱✱✱

Other language selection*

code

number,

Press

NUMBER keys

language codes on p. 48). To make corrections, press repeatedly to delete language code number, and correct. *1If the selected language is not offered,

the original disc language is selected.

(Please refer to

Operation

DVD

Page 46

Settings for DVD Operation (continued)

AUDIDI

O OUTPUT

LPCM(DVD)

: OFF

Audio Output

Select the digital output to be output from the optical digital audio output connector of DECK.

Press

ACTION

to display MENU.

DVD MAI N MENU

DI SC LANGUAGES

O OUTPUT

ST IL L MODE : F I LED TV MODE : L et t er b ox 4: 3 PARENTAL LOCK :

SELECT : SET : SET END : ACT ION

AUDI O OUTPUT

LPCM(DVD)

Dolby Digital : Bitstream d ts : OFF DRC : OFF SURROUND : OFF

SELECT : SET : SET END : ACT ION

■■

■ “LPCM (DVD)” selections

■■

OFF: Linear PCM of less than 48 kHz/16 bit is

output. When playing DVDs recorded in linear PCM of over 48 kHz/20 bit or 96 kHz, no digital audio is output. (Factory preset)

PCM: When playing DVDs recorded in linear PCM

of 48 kHz/20 bit/24 bit or 96 kHz, digital audio converted to 48 kHz/16 bit is output. (Digital output of PCM audio is restricted to 48 kHz/16 bit or below for copyright protection.)

■■

■ “Dolby Digital” selections

■■

Bitstream: Dolby Digital bitstream (1ch-5.1ch) is

OFF: No output.

■■

■ “dts” selections

■■

Bitstream: dts bitstream is output. (Factory preset) OFF: No output.

■■

■

“DRC (Dynamic Range Compression)” selections

■■

OFF: Normal audio range is selected. (Factory

ON: For dynamic sound even at low volume, this

■■

■ “SURROUND” selections

■■

Surround Sound creates the effect of sound coming from non-existent rear speakers even when only connected to a 2-channel stereo system.

OFF: No Surround Sound effect. (Factory preset) ON: Surround Sound effect.

Press

and go to step 2 to setup another item.

Or, press

output. (Factory preset)

preset)

is useful for late-night listening. [Dolby Digital DVDs only].

ACTION

Press

to select

LEVEL 8

“AUDIO OUTPUT,” and

press

to display screen.

: OFF

Press

to select an item, and

press

repeatedly for output. (See below.)

to redisplay DVD menu

ACTION

twice to exit.

SET

Ready Checklist

DECK is in DVD mode, press DVD.

Type of amplifier to be connected

No amplifier is connected AV amplifier (with digital

audio input connector) without Dolby Digital/dts decoder

AV amplifier including Dolby Digital decoder

AV amplifier including Dolby Digital/dts decoder

• Make settings according to amplifier connected to optical audio output as shown in above table.

• When a dts decoder is not connected, to enjoy dts DVD, please select audio output other than dts at the dts DVD menu screen. Otherwise, there will be no sound.

*1 Audio Output 2 from DECK is converted to

48 kHz/16 bit in addition to audio from digital audio output. To enjoy high quality sound at 48 kHz/20 bit /24 bit or 96 kHz, connect the amplifier or decoder directly to the Audio Output 2 connectors, not to the Digital Audio Output connector. [Select “OFF” at the “LPCM (DVD)”.]

*2 When connecting an amplifier (with an

optical digital input connector) which does not contain the Dolby Digital or dts decoder, be sure to select “OFF”. If “Bitstream” is selected, starting DVD play may cause such a high level of noise as to be harmful to your ears and damage the speakers.

*3 When a dts decoder is connected, please

select “Bitstream” in “dts”. If “OFF” is selected, there will be no sound.

Recommended setting

OFF

Dolby

Digital

OFF

OFF*

Bitstream

OFF*

Bitstream

dts

OFF

LPCM (DVD)

PCM*

Notes

• Turn off other surround effects when using this surround effect.

• For optimum effect, the distance between DECK and the listener should be about 3 or 4 times the distance between the right and left front speakers.

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : consumerproducts@panasonic.com

Page 47

TILLLL

MODE

ELD

TV MODE

Letterbox 4:3

*Important: If a remote control button does not work when pressed,

press the DVD button on the remote and try the button again.

Still Mode

Set to reduce jitter in a displayed still picture or a motion picture.

Press

ACTION

to display MENU.

DVD MAI N MENU

DI SC LANGUAGES

AUDIO OUTPUT

STI

MODE

TV MODE : L et t er b ox 4: 3 PARENTAL LOCK :

SELECT : SET : SET END : ACT ION

AUTO : “FIELD” (Field still) or “FRAME” (Frame still) is

FIELD: “FIELD” (Field still) is always selected.

FRAME:“FRAME” (Frame still) is always selected.

: F I ELD

LEVEL 8

automatically selected during the still mode. (Factory preset)

This setting will reduce jitter when compared with “AUTO” on some discs.

Some texts and fine patterns will be seen clearly when compared with “AUTO” on some discs.

Press

to select “STILL MODE,” and

SET

press

repeatedly

for mode. (See below.)

Press ACTION

to exit this mode.

TV Mode

Set the screen display style for wide-screen video material playback.

Press

ACTION

to display MENU.

DVD MAI N MENU

DI SC LANGUAGES

AUDIO OUTPUT ST IL L MODE : F

TV MODE

PARENTAL LOCK :

SELECT : SET : SET END : ACT ION

Pan & Scan 4 : 3 (Factory preset) :

Wide-screen video data is played in Pan & Scan style (left and right of screen is trimmed.)

• Video data not formatted in Pan & Scan will play

Letterbox 4 : 3 :

16 : 9 :

in letterbox style.

Wide-screen video data is played in Letterbox style (top and bottom of screen has black margin).

Set “16: 9” when using Wide-screen TV.

LED

: Letterbox 4:3

LEVEL 8

Press

to select “TV MODE,” and press

SET

repeatedly for mode. (See below.)

ACTION

SELECT

SET

Example

• Pan & Scan (Factory preset)

• Letterbox

Operation

DVD

Press

to exit this mode.

ACTION

Page 48

Language Code List

Enter the appropriate code number for the initial settings “AUDIO”, “SUBTITLE” and/or “MENUS” (see p. 45).

Code Language

6565 Afar 6566 Abkhazian 6570 Afrikaans 6577 Ameharic 6582 Arabic 6583 Assamese 6588 Aymara 6590 Azerbaijani 6665 Bashkir 6669 Byelorussian 6671 Bulgarian 6672 Bihari

Bengali; Bangla

6678 6679 Tibetan 6682 Breton 6765 Catalan 6779 Corsican 6783 Czech 6789 Welsh 6865 Danish 6869 German 6890 Bhutani 6976 Greek 6978 English 6979 Esperanto 6983 Spanish 6984 Estonian 6985 Basque 7065 Persian 7073 Finnish 7074 Fiji

Code Language

7079 Faroese 7082 French 7089 Frisian 7165 Irish 7168 Scots Gaelic 7176 Galician 7178 Guarani 7185 Gujarati 7265 Hausa 7273 Hindi 7282 Croatian 7285 Hungarian 7289 Armenian 7365 Interlingua 7378 Indonesian 7383 Icelandic 7384 Italian 7387 Hebrew 7465 Japanese 7473 Yiddish 7487 Javanese 7565 Georgian 7575 Kazakh 7576 Greenlandic 7577 Cambodian 7578 Kannada 7579 Korean 7583 Kashmiri 7585 Kurdish 7589 Kirghiz 7665 Latin

Code Language

7678 Lingala 7679 Laothian 7684 Lithuanian

Latvian, Lettish

7686 7771 Malagasy 7773 Maori 7775 Macedonian 7776 Malayalam 7778 Mongolian 7779 Moldavian 7782 Marathi 7783 Malay 7784 Maltese 7789 Burmese 7865 Nauru 7869 Nepali 7876 Dutch 7879 Norwegian 7982 Oriya 8065 Panjabi 8076 Polish

Pashto, Pushto

8083 8084 Portuguese 8185 Quechua

Rhaeto-Romance

8277 8279 Romanian 8285 Russian 8365 Sanskrit 8368 Sindhi

Serbo-Croatian

8372 8373 Singhalese

Code Language

8375 Slovak 8376 Slovenian 8377 Samoan 8378 Shona 8379 Somali 8381 Albanian 8382 Serbian 8385 Sundanese 8386 Swedish 8387 Swahili 8465 Tamil 8469 Telugu 8471 Tajik 8472 Thai 8473 Tigrinya 8475 Turkmen 8476 Tagalog 8479 Tonga 8482 Turkish 8484 Tatar 8487 Twi 8575 Ukrainian 8582 Urdu 8590 Uzbek 8673 Vietnamese 8679 Volapük 8779 Wolof 8872 Xhosa 8979 Yoruba 9072 Chinese 9085 Zulu

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : consumerproducts@panasonic.com

Page 49

Warning and Instruction Displays

These displays will alert you to a missed operation or provide further instructions.

PLEASE SET CLOCK BY PRESSING ACTION KEY

PLEASE PREPARE FOR TIMER REC

CHECK CASSETTE RECORD TAB

NO CASSETTE

TO CANCEL TIMER REC HOLD DOWN STOP KEY FOR APPROX 3 SEC

VIDEO HEADS MAY NEED CLEANING PLEASE INSERT HEAD CLEANING CASSETTE

OR REFER TO MANUAL

END : PLAY

VCR LOCK ACTIVATED

REMOTE CONTROL IS SET

TO CABLE/DSS MODE

USE VCR : VCR KEY

USE DVD : DVD KEY

CautionOSD

If you attempt to set or review a Timer Recording and the Clock is not set...

If DECK is not in Stop mode or a cassette with record tab is not inserted 2 minutes before a Timer Recording is about to begin...

If you press REC on the remote control or DECK, and a cassette is inserted with no record tab...

If you press PLAY, FF, REW, or REC on the remote control or DECK without a cassette inserted...

If you press STOP or POWER during a Timer Recording... (visible in VCR mode only)

If head cleaning becomes necessary while playing back a tape...

If you press a function button other than STOP/EJECT or POWER while DECK is in VCR Lock mode...

If you press an invalid key on the remote while in CABLE/DSS mode...

Page

24 25

20 21

28 29 34

REMOTE CONTROL IS SET TO TV MODE USE VCR : VCR KEY USE DVD : DVD KEY

PLEASE CHECK THE DISC,

AND FOR STAINS OR

SCRATCHES ON DISC

IT IS PROHIBITED TO COPY DVD/VIDEO CD/CD TO VHS

If you press an invalid key on the remote while in TV mode...

If you press PLAY, or DECK reads data from a stained or scratched disc in DVD mode. Also, if the type of disc is other than DVD, Video CD or CD...

If you press REC in DVD mode...

28 29 34

Information

For Your

Page 50

Before Requesting Service

Check the following points if you are having trouble with your DECK.

Power

No power…

Power turns itself off...

Recording & Playback

TV program cannot be recorded...

Timer recording cannot be performed…

There is no playback picture, or the playback picture is noisy or contains streaks...

Special effects playback, picture may contain some vertical jitter when using a TV with an Automatic Vertical Hold Control...

DECK cannot be controlled...

Remote Control

DECK cannot be remote controlled...

PROG buttons do not respond...

Correction

• Completely insert Power Plug into an AC outlet.

• Set POWER button to on.

• Make sure power source is active.

• Auto power-off (shutoff) occurs after about 5 min.

in DVD mode with no operation, or if there is no broadcast signal in TV or Playback mode. Turn the power back on. (pp. 23, 33)

Correction

• Check connections between DECK, external antenna, and TV.

• Check channel selections.

• Make sure your antenna system (CABLE or TV) is

correctly set. (Channels [p. 18])

• Make sure cassette record tab is intact. (p. 6)

• Confirm that clock is set to current time and date.

• Make sure Cable/DSS box (if used) is left on and

tuned to channel to be recorded.

• Set recording start/stop times correctly. (p. 24)

• Timer recording may not be performed or continued

if a power interruption occurs before or during a Timer Recording, even after power is restored.

• Select channel 3 or 4 on TV to match VCR output channel (3 or 4) (p. 16) or select LINE.

• Set VCR/TV selector to “VCR.”

• Adjust TRACKING control in either direction. (p. 6)

• Try Head Cleaning. (p. 6)

• Set TV’s Vertical Hold Control to MANUAL, then

adjust.

• Make sure DECK power is on.

• Check Remote batteries.

• Make sure VCR LOCK is set to off. (p. 33)

• Make sure Remote is in proper mode.(p. 28)

• Make sure Timer Recording is not in progress.

Correction

• Make sure DECK power is on.

• Make sure Remote is in VCR mode.

• Aim Remote Control directly at remote sensor on DECK. (p.9)

• Avoid any object blocking signal path.

• Check Remote batteries. (p. 4)

• Exposing DECK remote sensor to direct fluorescent

or outdoor light may cause signal interference.

• PROG functions are not available in COMPONENT

Video Output and S-VIDEO OUT. Set TV to either RF IN or VIDEO IN. (p. 10)

• Check Remote batteries. (p. 4)

• Press VCR or DVD button for DVD/VCR mode. (p. 28)

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : consumerproducts@panasonic.com

Page 51

Check the following points if you are having trouble with your DECK.

DVD/ Video CD/ CD

Play fails to start even when PLAY is pressed...

Play starts but then stops immediately... Picture is distorted during rapid

advance or rapid reverse... No Forward/Reverse Scene Search

play... Play does not start even when title is

selected... Audio soundtrack and/or subtitle

language is not the one selected at the initial settings...

No subtitles...

Alternative audio soundtrack (or subtitle) language cannot be selected...

Angle cannot be changed...

Miscellaneous

Programs cannot be viewed on TV...

Video cassette cannot be inserted...

Video cassette ejects when a recording is started or the power is turned off for timer recording...

In Stop mode, the motor (CYLINDER) continues to rotate...

The disc cannot be removed..

Correction

• This DECK cannot play discs other than DVDs, Video CDs and CDs.

• The disc may be dirty and require cleaning.

• Be sure disc is installed with label side up.

• The picture will be somewhat distorted at times:

this is normal.

• Some discs may have sections which prohibit Forward/Reverse Scene Search. (p. 23)

• Confirm the “DVD LOCK” setting. (p. 44)

• If the audio soundtrack and/or subtitle language

selected at DVD initial settings does not exist on the disc, it will not be accessible.

• Subtitles appear only when available on disc.

•“OFF” is selected at the changing subtitle

language. Select “ON” at the “Subtitle Languages” section (p. 36) to display the subtitles.

• Alternative language cannot be selected with discs which do not contain more than one language.

• For some discs, alternative language cannot be selected with the AUDIO or SUB TITLE button. Try selecting it from the DVD MENU if available.

• This function is dependent on software availability. Even if disc has multiple angles, they may be recorded for specific scenes only (ANGLE indicator on DECK lights up). (p. 37)

Correction

• Make sure TV is set to output of DECK.

• Check connections between DECK,

external antenna, and TV.

• Set VCR/TV selector to “TV.” (p. 21)

• Make sure proper signal source is selected.

• Insert the cassette with window side up; record

tab facing you.

• Make sure cassette record tab is intact. (p. 6)

• To enable Quick play mechanism, the cylinder will

rotate for about 3 minutes. This reduces response time from Stop to Play mode.

• First, unplug DECK. Then, prepare a rigid wire (e.g. an extended paper clip) and, applying moderate force, insert it straight into the hole at the base of the tray. The tray will eject a little. Now, pull the tray all the way out and remove the disc. (p. 9)

Information

For Your

If you cannot resolve the problem, please call the Customer Call Center for product assistance at 1-800-211-PANA (7262). To locate an authorized servicenter, please call toll free 1-800-211-PANA (7262). or send e-mail to : consumerproducts@panasonic.com

Page 52

Servicenter List

For Product Information, Operating Assistance, Literature Request, Dealer Locations, and all Customer Service inquiries please contact:

1-800-211-PANA (7262), Monday-Friday 9am-9pm Saturday-Sunday 9am-7pm,

EST. or send e-mail to : consumerproducts@panasonic.com

Web Site: http://www.panasonic.com You can purchase parts, accessories or locate your nearest servicenter by visiting our Web Site.

Accessory Purchases:

Customer Orders Only 800-332-5368 (Customer Orders Only) Panasonic Services Company 20421 84th Avenue South, Kent, WA 98032 (6 am to 5 pm Monday - Friday; 6 am to 10:30 am Saturday; PST) (Visa, MasterCard, Discover Card, American Express, Check)

Factory Servicenters Locations

CALIFORNIA

6550 Katella Avenue Cypress, CA 90630

800 Dubuque Avenue S. San Francisco, CA 94080

3878 Ruffin Road Suite A San Diego, CA 92123

FLORIDA

3700 North 29th Avenue Suite 102 Hollywood, FL 33020

GEORGIA

8655 Roswell Road Suite 100 Atlanta, GA 30350

ILLINOIS

1709 North Randall Road Elgin, IL 60123

MASSACHUSETTS

60 Glacier Drive Suite G Westwood, MA 02090

MINNESOTA

7850-12th Avenue South Airport Business Center Bloomington, MN 55425

OHIO

2236 Waycross Road Civic Center Plaza Forest Park, OH 45240

PENNSYLVANIA

2221 Cabot Blvd. West Suite B Langhorne, PA 19047

TEXAS

13615 Welch Road Suite 101 Farmers Branch, TX 75244

WASHINGTON

20425-84th Avenue South Kent, WA 98032

HAWAII

99-859 Iwaiwa Street Aiea, Hawaii 96701 Phone (808)488-1996 Fax (808)486-4369

Service in Puerto Rico

Matsushita Electric of Puerto rico, Inc. Panasonic Sales Company/ Factory Servicenter:

Ave. 65 de Infantería, Km. 9.5, San Gabriel Industrial Park, Carolina, Puerto Rico 00985

Phone (787)750-4300 Fax (787)768-2910

As of Sep. 2001

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : consumerproducts@panasonic.com

Page 53

Limited Warranty

Panasonic Consumer Electronics Company, Division of Matsushita Electric Corporation of America, One Panasonic Way Secaucus, New Jersey 07094

Panasonic Sales Company, Division of Matsushita Electric of Puerto Rico, Inc. AVE. 65 de Infantería, Km. 9.5 San Gabriel Industrial Park, Carolina, Puerto Rico 00985

PANASONIC/QUASAR Video Products

Panasonic Consumer Electronics Company or Panasonic Sales Company (collectively referred to as “the Warrantor”) will repair or replace this product with new or refurbished parts or equivalent product, free of charge, in the USA or Puerto Rico, in the event of a defect in materials or workmanship as follows (all time periods commence from the date of the original purchase):

PRODUCT

CAMCORDER

DVD/VCR DECK

DIGITAL STILL CAMERA

A/V MIXER TV/VCR, TV/DVD

TV/DVD/VCR COMBINATION

TV/HDR COMBINATION

Batteries (if included) - New rechargeable batteries in exchange for defective rechargeable batteries for ten (10) days. Non-rechargeable batteries are not warranted.

Tape (if included) - New video cassette tape in exchange for a defective video cassette tape for five (5) days. Memory cards (if included) - Exchange defective item for new one for ninety (90) days.

In-home, carry-in or mail-in service, as applicable, in the USA can be obtained during the warranty period by contacting a Panasonic Services Company (PASC) Factory Servicenter listed in the Servicenter Directory. Or call toll free contact number listed above, to locate an authorized PASC Servicenter. Carry-in or mail-in service in Puerto Rico can be obtained during the warranty period by calling the Panasonic Sales Company telephone number listed in the Servicenter Directory. This warranty is extended only to the original purchaser. A purchase receipt or other proof of the date of the original purchase is requires before warranty service is rendered.

This warranty only covers failures due to defects in materials and workmanship, which occur during normal use and does not cover normal maintenance, including, but not limited to, video and audio head cleaning. The warranty does not cover damage which occurs in shipment, or failures which are caused by products not supplied by the warrantor, or failures which result from accident, misuse, abuse, neglect, mishandling, misapplication, alteration, modification, faulty installation, set-up adjustments, improper antenna, inadequate signal pickup, maladjustment of consumer controls, improper operation, power line surge, improper voltage supply, lightning damage, commercial use such as hotel, office, restaurant, or other business or rental use of the product, or service by anyone other than a PASC Factory Servicenter or a PASC authorized Servicenter, or damage that is attributable to acts of God.

LIMITS AND EXCLUSIONS There are no express warranties except as listed above. THE WARRANTOR SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGE TO RECORDING MEDIA) RESULTING FROM THE USE OF THIS PRODUCTS, OR ARISING OUT OF ANY BREACH OF THE WARRANTY. ALL EXPRESS AND IMPLIED WARRANTIES, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR PARTICULAR PURPOSE, ARE LIMITED TO THE APPLICABLE WARRANTY PERIOD SET FORTH ABOVE. Some states do not allow the exclusion or limitation of incidental or consequential damages, or limitations on how long an implied warranty lasts, so the above exclusions or limitations may not apply to you. This warranty gives you specific legal rights and you may also have other rights, which vary, from state to state. If a problem with this product develops during or after the warranty period, you may contact your dealer or Servicenter. If the problem is not handled to your satisfaction, then write to the Consumer Affairs Department at the Panasonic Consumer Electronics Company address above.

SERVICE CALLS WHICH DO NOT INVOLVE DEFECTIVE MATERIALS OR WORKMANSHIP AS DETERMINED BY THE WARRANTOR, IN ITS SOLE DISCRETION, ARE NOT COVERED. COSTS OF SUCH SERVICE CALLS ARE THE RESPONSIBILITY OF THE PURCHASER. warvid 02/ 12/ 2001

PARTS

ONE (1) YEAR, EXCEPT CCD IMAGE SENSOR CCD IMAGE SENSOR

- SIX (6) MONTHS ONE (1) YEAR ONE (1) YEAR, EXCEPT

CCD IMAGE SENSOR CCD IMAGE SENSOR

- SIX (6) MONTHS ONE (1) YEAR

ONE (1) YEAR, EXCEPT CRT CRT - TWO (2) YEARS

Limited Warranty

LABOR

NINETY (90) DAYS

NINETY (90) DAYS NINETY (90) DAYS

CRT - NINETY (90) DAYS

NINETY (90) DAYS CRT - NINETY (90) DAYS

SERVICE

Carry-In or Mail-In

Carry-In or Mail-In Carry-In: 21” CRT

and Smaller In-Home or Carry-In:

22” CRT and Larger In-Home or Carry-In

CONTACT NUMBER

1-800-211-PANA(7262)

1-800-272-7033

1-800-211-PANA(7262) 1-800-211-PANA(7262)

1-888-843-9788

Information

For Your

Page 54

Spanish Quick Use Guide/ Guía para rápida consulta

F I JAC I ON AUTOMATICA DEL RELOJ ES I

NCOMPLETO

POR FAVOR FIJE

EL RELOJ

CON LA TECLA ACTION

9 /29 / 20 0 2

DOM 2 : 20P

HORA VERAN I EGA : ACT

CANAL FIJADO : CA

F I JAC I ON AUTOMAT I CA

COMPLETO

VERANO : ACT

ELEGIR : FIJAR :

SET

SALIR

ACT I ON

FIJAR RELOJ

1 /-- /----

ELEGIR MES

- - - - - - - - -- - - - - - - -- - - - - -

VERANO : ACT

FIJAR RELOJ

9 / 29 / 2002

DOM

12:00PM

FIJACION ES COMPLETO

- - - - - - - - -- - - - - - - -- - - - - -

Conexiones/Configuracion Inicial (READY TO PLAY)

Para ajustar el idioma, canal yPara ajustar el idioma, canal y

Favor realice la conexion de antena o cable antes de conectar el cordon de AC a la toma de pared.

Conectando el cordon de AC de la DECK en toma de pared iniciara automaticamente la busqueda de canales y colocacion de tiempo.

Conectando

Para Ant/Cable-DECK-TV

Conecte Ant/Cable a la entrada de antena

de la DECK (DECK In) Conecte la salida de la DECK (DECK Out) a

la entrada de antena de la TV (TV In) con el cable-accesorio RF incluido.

Televisor

DECK

VHF/UHF

Para Sistema Digital de Satelite (DSS)/ Convertidor de cable-DECK-TV

Conecte la salida del convertidor de cable

a la ”DECK In” con el RF cable accesorio incluido. Conecte “DECK Out” a la “TV In” con el

cable-accesorio incluido.

Realizando configuracion inicial

Presione el boton DECK del control remoto

para dicha modalidad. Encienda la TV y cambie a canal 3.

Conecte cordon de AC de la DECK a la

toma de pared. La DECK se activara e iniciara busqueda de canales y colocacion de tiempo.

• Si la pantalla abajo no aparece cheque la conexion DECK-TV y si la TV fue cambiada a el canal 3,trate cambiando a el canal 4.

• Para cambios a el canal de salida de la DECK favor hacer referencia a “VCR’s Output Channel” (p. 19).

Conectando cordon de AC a la toma de pared.

Televisor

Selecciones se realizaron automaticamente

cuando la configuracion termino, esta

VHF/UHF

DECK

Terminal OUT TO TV

pantalla aparece.

Si “Auto clock set is incomplete” aparece, coloque manualmente el tiempo, vealo abajo.

Realizando configuracion inicial

AUTOPROGRAMACION EN PROCESO

CANCELAR : STOP

FIJACION AUTOMATICA

RELOJ EN PROCESO

DEL

Al inicio, el idioma de la pantalla está fijado a inglés. Para cambiar el idioma consulte la página 18.

Si la colocacion de tiempo fue incompleta.

Presione la tecla ACTION en el control remoto

para visualizar la pantalla del menú RELOJ.

Terminal OUT TO TV

Terminal IN FROM ANT.

Entrada (IN) desde

ANT./CABLE

Estuche convertidor de TV por cable

Entrada (IN) desde ANT./CABLE

CANCELAR : STOP

Si usa convertidor de cable solo enciendala y seleccione el canal PBS en su horario de uso u horario de zona. Si utiliza receptor DSS este debe estar apagado.

PRECAUCION

Si se sobre ajusta “NUT TYPE” el cable coaxial RF podria dañar las terminales de conexion. Ajusta ligeramente utiliza solo los dedos.

Presione para seleccionar el mes y SET

para ajustar. De la misma forma, seleccione y ajuste la fecha, año, hora y DST (Hora de Verano).

Presione dos veces la tecla ACTION para

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : consumerproducts@panasonic.com

Por ayuda llame al 1-800-211-PANA(7262) o envie e-mail a : consumerproducts@panasonic.com

poner el RELOJ en marcha y salir.

Page 55

Operaciones básicas para la reproducción

Inserte un cassette,

• La alimentación del DECK se activa. En la Pantalla de Visualización Multi Función se ilumina “VCR”.

Presione PLAY para reproducir el cassette.

• Si el cassette no tiene lengüeta de prevención de grabación (página 6), se inicia la reproducción automáticamente.

Detalles especiales durante la grabación

Presione FF/SLOW+ o REW/SLOW- para

búsqueda de escenas hacia delante/ hacia atrás. Presione PLAY para liberar. Luego de que la búsqueda se ha iniciado, cada vez que presione FF/SLOW+ o REW/SLOW- se cambia la velocidad como sigue: [SLP] aprox. 21X [LP] aprox. 9X [SP] aprox. 7X

↔↔

↔ aprox. 9X

↔↔

↔ aprox. 7X

↔↔ ↔↔

↔ aprox. 3X

↔↔

Si la imágen se interrumpe con la velocidad de 21x, 9x o 7x, cambie la velocidad a 9x, 7x o 3x. Presione PAUSE/STILL para imagen Fija (Congelada).

Presione PLAY para liberar. Presione PAUSE/STILL en el modo de

imagen fija para imágenes cuadro a cuadro.

Presione PLAY para liberar. Presione FF/SLOW+ o REW/SLOW- en el

modo de imagen fija para imágenes cuadro a cuadro. Presione PLAY para liberar.

Presione STOP para detener el cassette.

Presione REW/SLOW- o FF/SLOW+ en el

modo de parada para rebobinado/avance rápido del cassette. Presione EJECT en el control remoto, o STOP/EJECT en el DECK para expulsar el cassette.

Operaciones básicas para la grabación

Inserte el cassette con lengüeta de

protección de grabación (pág. 6).

Presione CH / , o las teclas de números

para seleccionar el canal.

Presione SPEED para seleccionar la

velocidad de grabación (pág.6)

• SP = Reproducción estándar,

• LP = Larga duración,

• SLP = Superlarga duración.

Presione REC para comenzar a grabar.

• Para eliminar escenas indeseadas, presione PAUSE/STILL para pausar, y al presionar nuevamente se reanuda la grabación.

• No podrá ver otro canal durante la grabación.

Presione STOP para detener la grabación.

Programación fácil para la grabación con temporizador

Presione PROG

para visualizar PROGRAM.

N I C I

FECHA

7 SAB

SLP

HOY

ELEGIR FECHA DE I N I C I O

ELEGIR FIJAR TERMINAR

PARADA

--:-- --:-- --

:SET

PROG

Orden para elegir

Ejemplo

Fecha de hoy

2) Para ajustar los ítems que quedan,

presione para seleccionar y presione SET para ajustar los tiempos de INICIO/

PARADA, CANAL, o entrada de LÍNEA (pág.

35), y velocidad del cassette (SP, LP, SLP). Presione PROG para finalizar PROGRAM.

I N I C

2 : 00 P 3 : 20 P

-- -- : --

-- : --

CANC

ELAR: ADD / DLT

ELEGIR 1- 8 :

: SET

ENTRAR SAL I R

: PROG

PARADA CA VEL

-- : -- --

Grabación de un toque (grabar en

marcha),

Presione REC repetidamente para ajustar la hora de grabación (30 min - 4 horas).

• La videograbadora termina la grabación a una hora programada.

Grabación normal

1) Para ajustar la FECHA de

grabación, presione

para seleccionar: 1-31 = una vez, o DIARIO = a la misma hora de lunes a viernes, o SEMANA = a la misma hora cada semana y presione SET para ajustar.

/ Orden para elegir

SEMANAL

Presione

02 SLP

para seleccionar un número

que no está usando para ingresar mas programas y

presione SET

(

SAB

SEMANAL

(

LUN

)

para ajustar. Luego repita el paso 2. O

Presione nuevamente PROG para salir.

0:30 1:00

1:302:003:004:00

)

SEMANAL

(

DOM

68 9

DIARIO

)

Guía para rápida

consulta

Page 56

Spanish Quick Use Guide/ Guía para rápida consulta

Operaciones básicas del DVD

Presione

1) Presione

2) Ponga un disco en la bandeja de disco.

• Sujete el disco sin tocar ninguna de sus superficies, póngalo con el lado donde esté impreso el título hacia arriba, alinéelo con las guías y póngalo en su posición apropiada.

Disco de 3”(8 cm) Disco de 5” (12 cm)

Presione

La bandeja del disco se cierra automáticamente.

• Si está usando un DVD interactivo (Interactive DVD)

o un Vídeo CD con contol de reproducción (playback control) y aparece un menú de títulos (TITLE MENU) en la pantalla, siga al paso 5.

Presione o las teclas numéricas para

seleccionar el artículo deseado.

Presione Si usa las teclas numéricas, la reproducción

comienza automáticamente.

Presione

■ Para buscar una escena particular

Búsqueda hacia adelante

Presione

Búsqueda hacia atrás

Presione (Para liberar, presione

■ Para saltar un capítulo o una pista

Salto hacia adelante

Presione

Un capítulo (DVD) o una pista (Vídeo CD/CD) se salta cada ves que se oprime la tecla.

Salto hacia atrás

Presione l

■■

■ Para ver una imagen fija

■■

Presione (Para liberar, presione

■ Para ver imágenes cuadro a cuadro

(DVD/Vídeo CD) Presione

La imagen avanza un cuadro cada vez que presiona la tecla. (Para volver a la reproducción normal, presione

■ Para ver en cámara lenta (DVD/Vídeo CD)

Presione (Para liberar, presione

POWER

en el control remoto o el aparato.

DVD

para seleccionar el modo DVD.

OPEN/CLOSE

PLAY

para iniciar la reproducción.

SET

para la reproducción.

STOP

para parar la reproducción.

OPEN/CLOSE

FF/SLOW+

REW/SLOW-

SKIP

PAUSE/STILL

FF/SLOW+

para expulsar el disco.

en el modo de reproducción.

PLAY

)

l en el modo de reproducción.

en el modo de reproducción.

durante la reproducción.

PLAY

)

en el modo de imagen fija.

REW/SLOWPLAY

)

POWER

PLAY

REW/ SLOW-

STOP

NUMBER

keys

SKIP SELECT

SET

PLAY

en el modo de imagen fija.

OPEN/ CLOSE

DVD

FF/ SLOW+

PAUSE/ STILL

SKIP

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : consumerproducts@panasonic.com

Por ayuda llame al 1-800-211-PANA(7262) o envie e-mail a : consumerproducts@panasonic.com

Page 57

Funcionnamiento del DVD utilizando

CAPIPI

TULO

STA

visualizaciones en pantalla

Cuando se presiona DISPLAY, la visualización en pantalla muestra la información del disco (título / capítulo / número de lista, tiempo transcurrido de reproducción, audio / idioma del subtítulo, y ángulo) e información (repetir la reproducción, modo reproducción, Karaoke vocal encendido / apagado, etc.).

DISPLAY

Presione

para visualizar Visualizaciones en pantalla.

• Cada vez que se presione en pantalla cambia como se muestra a continuación.

DISPLAY

en el modo reproducción o parada

DISPLAY

, la visualización

Información seleccionada del disco

Información seleccionada de del DECK

Pantalla normal

Presione (o ) para seleccionar el ítem deseado.

Presione

Presione para seleccionar el ajuste deseado.

Presione

SET

para ajustar.

SET

para ajustar.

Para volver a la pantalla normal, Presione repetidamente

PIPISTA

: 12

PBC : I NACTIVO 0 : 12 :34

PIPISTA

PBC : I NACTIVO 0 : 12 :34

FI JAR : SET SIGUI ENTE: DI SPLAY

VI DEO CD

: 17

VI DEO CD

CLEAR o DISPLAY

T ITULO : 12 DVD

CAPITULO

: 11 0:12:34

T ITULO : 12 DVD

TULO

: 24

ELEGI R: FI JAR : SET SIGUI ENTE: DI SPLAY

0:12:34

CLEAR

SELECT

SET

Guía para rápida

consulta

Page 58

Spanish Quick Use Guide/ Guía para rápida consulta

Fijaciones iniciales

Presione DVD para seleccionar el mode DVD.

Presione ACTION en el modo de parada para

visualizar MENU.

Presione para seleccionar el artículo deseado.

Presione

IDIOMAS DEL DISCO

Todos los idiomas ofrecidos en el disco pueden ser ajustados, Si el idioma ajustado no es ofrecido en el disco, se seleccionará el idioma original del disco.

SALIDA DE AUDIO

Puede usted ajustar la salida audio procedente del terminal de salida audio digital.

DETENER RASTREO

Para seleccionar “CAMPO” o “CUADRO fijo” para prevenir inestabilidad o para permitir ver textos pequeños o patrones finos claramente en el modo de imagen fija.

PREFERENCIA

Para seleccionar si el material del vídeo para pantalla ancha será vuelto a reproducir en el estilo Pan&Scan, en el estilo Letterbox o en el estilo 16 : 9 en la pantalla.

Presione para seleccionar el artículo deseado.

Presione

Volver a visualizar el menú de DVD para

continuar el ajuste.

Presione

otro ajuste o, para salir, presione veces.

SET

ACTION

y pase al paso 3 para ajustar

ACTION

tres

Selección de IDIOMAS DEL DISCO [DVD solamente]

Seleccione “AUDIO”

(Fijación de fábrica : inglés)

Inglés / Español / Francés / Japonesa : Originl : Se seleccionará el idioma

OTRO **** : Se puede seleccionar el otro

Seleccione “SUBTITULO”

AUTO : Se seleccionará el mismo que fue

• Si el idioma seleccionado en la preparación de “AUDIO” se utiliza durante la reproducción, los subtítulos no aparecerán.

• Si se utiliza otro idioma durante la reproducción, los subtítulos aparecerán en el idioma seleccionado en la preparación de “AUDIO”

Inglés / Español / Francés / Japonesa : OTRO **** : Se puede seleccionar el otro

Seleccione “MENU”

(Fijación de fábrica : inglés)

Inglés / Español / Francés / Japonesa : OTRO **** : Se puede seleccionar el otro

original de cada disco.

idioma.

(Fijación de fábrica)

seleccionado en la preparación de “AUDIO”.

idioma.

Cambio del idioma de subtítulos [DVD solamente]

EI idioma de los subtítulos seleccionado al hacer las fijaciones iniciales se puede cambiar por otro idioma diferente, si éste se encuentra disponible.

Presione

durante la reproducción. Cuando no haya subtítulos grabados, “-” se visualizará en lugar del número de idioma.

Presione para seleccionar el idioma deseado.

Presione (o ) para ajustar.

Presione para seleccionar “ACTIVO” o “INACTIVO.”

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : consumerproducts@panasonic.com

Por ayuda llame al 1-800-211-PANA(7262) o envie e-mail a : consumerproducts@panasonic.com

SUBTITLE

Cambio del idioma de la pista de

sonido [DVD solamente]

EI idioma de la pista de sonido seleccionado al hacer las fijaciones iniciales se puede cambiar por otro idioma diferente, si éste se encuentra disponible.

Presione

la reproducción para visualizar la pantalla AUDIO.

Presione para seleccionar idioma.

AUDIO

durante

Page 59

Visión desde otro ángulo

ANGULO

• DVD Karaoke (1 vocal) VOCAL ON VOCAL OFF

• DVD Karaoke (2 vocals) VOCAL V1 + V2 VOCAL V1 VOCAL V2 VOCAL OFF

• Video CD LR L R

[DVD solamente]

Algunos discos DVD tienen escenas que han sido filmadas simultáneamente desde un número de ángulos diferentes. Con estos discos, la misma escena podrá verse desde cada uno de estos ángulos diferentes utilizando el botón ANGLE.

ANGULO

: 1

ELEGI R : FI JAR :SET

ANGULO

: 2

ELEGI R : FI JAR :SET

Presione

durante la reproducción para visualizar la pantalla de ángulo.

Presione para seleccionar el ángulo deseado.

ANGLE

Utilización de un menú de títulos [DVD solamente]

Algunos discos con películas, por ejemplo, vienen con dos o más títulos. Si el disco tiene un menú de títulos grabados, el botón TITLE podrá utilizarse para seleccionar el título de la película.

Presione

Ahora se visualiza una lista de los títulos del disco.

T I TLE MENU

Dogs

Love

of the world

TITLE

Cas t l es

i r

Dogs

durante la reproducción.

Presione o las teclas de números para

seleccionar el título deseado.

Presione

SET

Selección de vocal para los discos de Karaoke [DVD/Video CD]

Presione

para visualizar la pantalla AUDIO.

AUDIO

durante la reproducción

Presione (o ) para seleccionar el ajuste deseado.

Presione (o ) para ajustar. (DVD solamente)

Utilización de un menú de DVD [DVD solamente]

Algunos discos DVD tienen estructuras únicas de menús llamadas menús DVD. Por ejemplo, los DVDs programados con un contenido complejo proporcionan menús guía, y los grabados con varios idiomas proporcionan menús para audio e idiomas de subtítulos. Aunque los contenidos de los menús DVD y la operación cambian de disco a disco, a continuación se explica la operación básica cuando se utiliza esta característica.

Presione

El menú de DVD introducido en el disco se visualiza ahora.

DVD MENU

1 . SUBT I TLE 2 . AUD

3 . ANGLE

durante la reproducción.

Presione o las teclas de números

para seleccionar el ítem deseado.

Presione

SET

Ampliación de la imagen [DVD solamente]

Durante la reproducción de un DVD, puede ampliar partes específicas de una imagen y seleccionar la relación de zoom usando el botón ZOOM.

Presione

tamaño de la imagen como se indica a continuación:

■ Use los botones , , y para desplazar la posición hacia arriba, hacia abajo, hacia la

ZOOM

repetidamente para cambiar el

izquierda o hacia la derecha.

2da

3da

Guía para rápida

consulta

Page 60

Index

DECK & VCR

A ACTION button ..............................................8, 18

Accessories ......................................................... 4

ADD/DELETE button (Add or Delete a Channel) . 8, 19

Audio Broadcast types (Stereo/SAP/Mono) .... 26

Audio Mode (Playback, Recording) ................. 27

Auto Operation Functions ...............................31

Auto Shut-Off .................................................... 33

B Batteries .............................................................. 4

C Channel (“SET UP CHANNEL”) ....................... 18

Channel Up/Down, Tracking/V-Lock Button ...6, 8

Clock (“SET CLOCK”) ....................................... 18

Commercial Skip ............................................... 31

Connections .............................................12 ~ 15

Copy Your Tapes (Dubbing) ............................ 35

COUNTER RESET button ............................ 8, 32

D DISPLAY button ........................................... 8, 11

DSS/CABLE mode button ...........................8, 28

DST (Daylight Saving Time) ............................. 19

E EJECT button ...............................................8, 20

ENTER button (For tuning TV Channel) .....8, 28

F FAST FORWARD/SEARCH button .............8, 20

H Head Cleaning .................................................... 6

I Index Search .................................................... 30

Indicator (Multi Function Display) ....................11

Initial Setup (Ready to Play) ..................... 16, 17

INPUT button ................................................ 8, 35

L Limited Warranty .............................................. 53

Location of Controls (Remote, DECK) ..... 8 ~ 10

M Multi-Brand Control .................................... 28, 29

O On-Screen Displays (VCR) ................................ 11

One Touch Recording ...................................... 21

DVD

A ACTION button .............................................8, 45

ANGLE button (Multiple Angle Viewing) .....8, 37

AUDIO CONTROL button ............................8, 40

AUDIO button (Audio Soundtrack Language) ..8, 36 Audio Output (For Selecting Audio Output) ... 46

Auto Power Off Function .................................. 23

C CLEAR button ........................................ 8, 39, 44

Component Video Output ......................... 10, 13

D Disc Languages ................................................ 45

DISPLAY button (“On-Screen Display”) ...... 8, 41

DVD Menu ......................................................... 3 8

DVD mode button.........................................8, 28

DVD Lock Ratings ............................................ 4 4

F Frame by Frame Picture ...................................23

Forwards/Reverse Chapter/Track .................... 23

Forwards/Reverse Scene Search.................... 23

K Karaoke (Vocal Selection for Karaoke Discs) .... 37

L Language Code List ........................................ 48

M MENU button (To display DVD Menu) ........ 8, 38

MP3 ................................................................... 43

Multiple Angle Viewing ..................................... 37

O OPEN/CLOSE button ................................... 8, 22

Optical Digital Audio Output ..................... 10, 15

Panasonic Consumer Electronics Company, Division of Matsushita Electric Corporation of America

One Panasonic Way Secaucus, New Jersey 07094

Panasonic Sales Company (“PSC”), Division of Matsushita Electric of Puerto Rico, Inc.

Ave. 65 de Infantería. Km. 9.5 San Gabriel Industrial Park, Carolina, Puerto Rico 00985

P PAUSE/STILL button (Still Picture) ............. 8, 20

PLAY button (Playback a Tape) .................8, 20

POWER button ................................................... 8

PROG button (PROGRAM) .......................... 8, 24

Program Clear, Review, Replace ..................... 25

Program End Search ........................................30

Q Quality Picture ..................................................... 6

R REC button (Record on a Tape) .................8, 21

Record Tab ......................................................... 6

Remote Sensor ................................................... 9

Remote Warning ............................................... 34

Repeat Play ...................................................... 32

REWIND/SEARCH button ............................ 8, 20

S SAP/Hi-Fi ........................................................... 27

SEARCH (Index and Program End Search) ... 30

Servicenter List ................................................. 52

SLOW+/SLOW- button (Slow Motion Picture) .. 8, 20

Spanish Quick Use Guide ....................... 54 ~ 59

Specifications ...................................................... 7

SPEED button ..............................................8, 21

Still (Freeze) Picture ......................................... 20

STOP button .................................................8, 20

T Tape Position, Tape Status............................. 34

Timer Recording ............................................... 24

Trouble Shooting ....................................... 50, 51

TV mode button ............................................8, 28

V VCR Lock .......................................................... 3 3

VCR mode button......................................... 8, 28

VCR/TV button......................................... 8, 9, 21

VOLUME +/- button (TV Volume) ...............8, 28

W Warning and Instruction Displays ....................49

Weak Signal Display ......................................... 33

Z ZERO SEARCH button ................................8, 32

P PLAY button (Play a Disc) ...........................8, 22

Program Play (For Video CD/ CD) ................... 39

PROGRESSIVE button ...................................... 9

Progressive Scan .............................................10

R Random Play (For Video CD/ CD) ................... 40

Repeat Play ...................................................... 42

Resume Function .............................................23

RETURN button ............................................8, 22

S SEARCH button

(Forward/Reverse Scene Search) .............8, 23

SKIP l or l button

(Forward/Reverse Chapter/Track) ............. 8, 23

SLOW+/SLOW- button (Slow Motion Picture) . 8, 23

Sound Output Level ......................................... 40

STILL button (Still Picture or Pause) ..........8, 23

Still Mode (For selecting “FIELD” or “FRAME”)... 47

STOP button .................................................8, 22

SUBTITLE button

(For selecting Subtitle Language) ............. 8, 36

SURROUND button ...................................... 8, 23

S-Video Out ............................................... 10, 13

T TITLE button (Title Menu) ............................8, 38

TV Mode (For selecting the screen display style) ....47

V Video CD ........................................................... 23

Z ZOOM button (Picture Zoom) ......................8, 37

Printed in Indonesia

LSQT0580A

S0102-0

Panasonic PV-D4742, PV-D4752 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual

Important Safeguards and Precautions

Before Using

Table of Contents

DECK & Cassette Information

Location of Controls

Connections

Initial Setup for Basic Connections (Ready to Play)

Playback/ Record on a Tape

Basic DVD Operation

Timer Recording

MTS Broadcast/ VHS Hi-Fi Stereo System

Multi-Brand Control Feature

Special VCR Features

Copying Your Tapes (Dubbing)

Disc Operation

DVD Operation using On-Screen Displays

MP3 Playback Operation

DVD Lock Feature

Settings for DVD Operation

Language Code List

Warning and Instruction Displays

Before Requesting Service

Servicenter List

Limited Warranty

Index