Panasonic PV-D4735S User Manual

DVD/VCR DECK

Operating Instructions

Model No.

PV-D4735S

Connections and Initial Setup Procedures are on pages 12 to 17.

For Your InformationVCR Operation DVD OperationBasic OperationInitial Setup

MULTI FORMAT PLAYBACK

Ability to play back may depend on recording conditions.

As an ENERGYSTAR Partner, Panasonic Corporation of North America has determined that this product or product model meets the

NERGYSTAR guidelines for energy efficiency.

Please read these instructions carefully before attempting to connect, operate or adjust this product. Please save this manual. Spanish Quick Use Guide is included. (Guía para rápida consulta en español está incluida.)

For assistance, please call : 1-800-211-PANA(7262) or, contact us via the web at:http://www.panasonic.com/contactinfo

LSQT0907 A

Important Safeguards and Precautions

TO REDUCE THE RISK OF ELECTRIC SHOCK, FIRE, INJURY TO PERSONS OR DAMAGE TO THIS PRODUCT, READ AND RETAIN ALL SAFETY AND OPERATING INSTRUCTIONS. HEED ALL WARNINGS IN THE MANUAL AND ON THE PRODUCT.

INSTALLATION

1 POWER SOURCE CAUTION

Operate only from a power source indicated on the unit or in this manual. If necessary, have your Electric Utility Service Company or Video Products Dealer verify the power source in your home.

2 POLARIZED OR GROUNDING PLUG

As a safety feature, this product comes with either a polarized power cord plug (one blade is wider than the other), or a three-

wire grounding type plug. POLARIZED PLUG CAUTION: This plug will only fit into an outlet one way. If you cannot fully insert the plug, try reversing it. If it still will not fit, have an electrician install the proper wall outlet. Do not defeat the safety feature by tampering with the plug. GROUNDING PLUG CAUTION: This plug will only fit into a three-hole grounding outlet. If necessary, have an electrician install the proper outlet. Do not defeat the safety feature by tampering with the plug.

3 POWER CORD

Make sure power cords are routed so that they are not likely to

have anything rest on them, roll over them, or be in the way of

walking traffic. If an extension cord is used, make sure it also

has either a polarized or grounded plug and that the cords can

be securely connected. Frayed cords, damaged plugs, and

damaged or cracked wire insulation are hazardous and should

be replaced by a qualified service technician.

Overloaded outlets and extension cords are fire hazards and

should be avoided.

4 DO NOT BLOCK VENTILATION HOLES

Ventilation openings in the cabinet release heat generated during

operation. If they are blocked, heat build-up inside the unit can

cause failures that may result in a fire hazard or heat damage to

cassettes or discs.

For protection, follow these rules:

a. Never cover ventilation slots or the unit while in use, or

operate the unit when placed on a bed, sofa, rug, or other soft surface.

b. Avoid built-in installation, such as a book case or rack,

unless proper ventilation is provided.

5 PLACEMENT: AVOID EXTREMELY HOT LOCATIONS OR

SUDDEN TEMPERATURE CHANGES

Do not place the unit over or near heater or radiator, in direct

sunlight, inside closed vehicles, in high temperature [over 104°F

(40°C)], or in over 75% humidity. If the unit is suddenly moved

from a cold place to a warm one, moisture may condense in the

unit and on the tape causing damage. Never subject the unit to

vibration, impact, or place it so that the surface is tilted as

internal parts may be seriously damaged.

6 TO AVOID PERSONAL INJURY

• Do not place unsecured equipment on a sloping surface.

• Do not place this unit on any support that is not firm, level, and adequately strong. The unit could fall causing serious injury to a child or adult and damage to the unit.

• An appliance and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the appliance and cart combination to overturn.

• Carefully follow all operating instructions and use the manufacturer's recommended accessories when operating this unit or connecting it to any other equipment.

1 SAFE ANTENNA AND CABLE CONNECTION

If an outside antenna or cable system is connected to the equipment, be sure the antenna or cable system is grounded so as to provide some protection against built up static charges and voltage surges. Section 810 of the National Electrical Code, ANSI/NFPA 70 (in Canada, part 1 of the Canadian Electrical Code) provides information with respect to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna discharge unit, connection to grounding electrodes and requirements for the grounding electrode.

2 KEEP ANTENNA CLEAR OF HIGH VOLTAGE POWER LINES OR

CIRCUITS

An outside antenna system should be located well away from power lines, electric light or power circuits and where it will never come into contact with these power sources if it should happen to fall. When installing an outside antenna, extreme care should be taken to avoid touching power lines, circuits or other power sources as this could be fatal. Because of the hazards involved, antenna installation should be left to a professional.

If the unit has been in storage or moved to a new location, refer first to the INSTALLATION section of these safeguards.

1 KEEP THE UNIT AWAY FROM WATER OR MOISTURE OF ANY KIND. 2 IF EQUIPMENT IS EXPOSED TO RAIN, MOISTURE, OR STRONG

IMPACT, unplug the unit and have it inspected by a qualified service technician

before use.

3 DURING AN ELECTRICAL STORM

During a lightning storm, whether indoors or outdoors, or before leaving the unit unused for extended periods of time, disconnect all equipment from the power source as well as the antenna and cable system.

4 WHEN THE UNIT IS PLUGGED IN

• Never expose the unit to rain or water. DO NOT OPERATE if liquid has been spilled into the unit. Immediately unplug the unit, and have it inspected by a service technician. Fire and shock hazards can result from electrical shorts caused by liquid contact inside.

• Never drop or push any object through openings in the unit. Some internal parts carry hazardous voltages and contact can cause electric shock or fire hazard. Do not put any foreign object on the disc tray.

• Avoid placing the unit directly above or below your TV set as this may cause electrical interference. Keep all magnets away from electronic equipment.

5 USING ACCESSORIES

Use only accessories recommended by the manufacturer to avoid risk of fire, shock, or other hazards.

6 CLEANING THE UNIT

Unplug the unit. Then, use a clean, dry, chemically untreated cloth to gently remove dust or debris. DO NOT USE cleaning fluids, aerosols, or forced air that could over-spray, or seep into the unit and cause electrical shock. Any substance such as wax, adhesive tape, etc. may mar the cabinet surface. Exposure to greasy, humid, or dusty areas may adversely affect internal parts.

1 DO NOT SERVICE THIS PRODUCT YOURSELF

If, after carefully following the detailed operating instructions, this product does not operate properly, do not attempt to open or remove covers, or make any adjustments not described in the manual. Unplug the unit and contact a qualified service technician.

2 IF REPLACEMENT PARTS ARE REQUIRED

Make sure the service technician uses only parts specified by the manufacturer, or those having the same safety characteristics as the original parts. The use of unauthorized substitutes may result in fire, electric shock, or other hazards.

3 HAVE THE SERVICE TECHNICIAN PERFORM A SAFETY CHECK

After any service or repairs to the unit, request the service technician to conduct a thorough safety check as described in the manufacturer’s service literature to ensure that the unit is in safe operating condition.

OUTDOOR ANTENNA INSTALLATION

NEC - NATIONAL

ELECTRICAL CODE

ELECTRIC SERVICE EQUIPMENT

USING THE UNIT

SERVICE

GROUND CLAMP

ANTENNA LEAD IN WIRE

ANTENNA DISCHARGE UNIT (NEC SECTION 810-20)

GROUNDING CONDUCTORS (NEC SECTION 810-21)

GROUND CLAMPS

POWER SERVICE GROUNDING ELECTRODE SYSTEM (NEC ART 250, PART H)

Safety Precautions/Mesures de sécurité

To prevent fire or shock hazard, do not expose this equipment to rain or moisture.

To prevent electric shock, match wide blade of plug to wide slot, fully insert.

AVERTISSEMENT:

Afin de prévenir tout risque d’incendie ou de chocs électriques, ne pas exposer cet appareil à la pluie ou à une humidité excessive.

ATTENTION:

Pour éviter les chocs électriques, introduire la lame la plus large de la fiche dans la borne correspondante de la prise et pousser jusqu’au fond.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK)

NO USER-SERVICEABLE PARTS INSIDE

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL

This symbol warns the user that uninsulated voltage within the unit may have sufficient magnitude to cause electric shock. Therefore, it is dangerous to make any kind of contact with any inside part of this unit.

This symbol alerts the user that important literature concerning the operation and maintenance of this unit has been included. Therefore, it should be read carefully in order to avoid any problems.

CAUTION:

UNIT IS A CLASS I LASER PRODUCT. THIS UNIT USES A VISIBLE LASER BEAM WHICH COULD CAUSE HAZARDOUS RADIATION EXPOSURE IF DIRECTED. BE SURE TO OPERATE THE UNIT CORRECTLY AS INSTRUCTED.

WHEN THIS UNIT IS PLUGGED TO THE WALL OUTLET, DO NOT PLACE YOUR EYES CLOSE TO THE OPENING OF THE DISC TRAY AND OTHER OPENINGS TO LOOK INTO THE INSIDE OF THIS UNIT.

USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.

DO NOT OPEN COVERS AND DO NOT ATTEMPT TO REPAIR YOURSELF. REFER SERVICING TO QUALIFIED PERSONNEL.

CAUTION:

LASER RADIATION WHEN OPEN. DO NOT STARE INTO BEAM.

ATTENTION:

RAYONNEMENT LASER EN CAS D’OUVERTURE. NE PAS REGARDER DANS LE FAISCEAU.

(Inside of product)

FCC NOTE:

This equipment has been tested and found to comply with part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when operated in a residential environment. If this equipment does cause interference to radio or television reception, which can be determined by turning the equipment off and on, use the equipment in another location and/or utilize an electrical outlet different from that used by the receiver. If necessary, consult the dealer or an experienced radio/TV technician for help. The user may find the booklet, “Something About Interference” available from FCC local regional offices helpful.

FCC Caution:

To assure continued compliance, (example- use only shielded interface cables when connecting to other devices.) Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.

Region Management Information:

This DECK is designed and manufactured to respond to the Region Management Information that is recorded on a DVD disc. If the Region number described on the DVD disc does not correspond to the Region number of this DECK, this DECK cannot play this disc.

● The Region number for this DECK is “1”.

● The Player will play DVD-Video marked with labels

containing “1” or “ALL”.

Example:

ALL

Before Using

Congratulations

on your purchase of one of the most sophisticated and reliable products on the market today. Used properly, it will bring you years of enjoyment. Please fill in the information below. The serial number is on the tag located on the back of your DECK.

• Date of Purchase

• Dealer Purchased From

• Dealer Address

• Dealer Phone No.

• Model No.

• Serial No.

Accessories

Remote Control

EUR7724KE0

Loading the Batteries

Battery replacement caution

• Do not mix old and new batteries.

• Do not mix alkaline with manganese batteries.

Record/ Playback Time

Only use tapes with the mark in this DECK.

Tape Speed

Setting

(Standard Play)

(Super Long Play)

SLP

For assistance, please call : 1-800-211-PANA(7262) or, contact us via the web at:http://www.panasonic.com/contactinfo

2 Hours

6 Hours 8 Hours

PV-D4735S

Batteries 2 “AA”

RF Coaxial Cable LSJA0418

To order accessories, call toll free 1-800-332-5368.

1) Open cover.

2) Insert batteries as marked.

3) Close cover.

Type of Video Cassette

2 Hours

40 Minutes

T180T160T120

3 Hours

9 Hours

Head Cleaning

Playing older or damaged tapes may eventually cause video heads to become clogged.

Video Head Clog Sensor

During playback, this screen appears if clogging is detected. To remove screen, press PLAY on the remote or DECK.

• Use “dry” type head cleaning cassette only.

(Part No. NV-TCL30PT is recommended.)

• Follow cleaning tape instructions carefully. Excessive use of tape can shorten head life.

• If head clog symptoms persist, contact your nearest servicenter by visiting our Web Site (see p. 61).

Cleaning DECK

Use a soft cloth or dusting attachment of a vacuum cleaner to remove dust from the ventilation holes on the back sides and bottom of the cabinet. Plastic surfaces are easily scratched and can be marred by alcohol and various solvents. Avoid excessive use of oil-based furniture polishes since the materials used in the cabinet will accumulate more dust. We recommend using a non-abrasive, antistatic cleaner and polisher.

Features for a Quality Picture (VCR)

Digital Auto Picture

Automatically controls the video output signal for less noise depending on the tape condition.

Digital Auto Tracking

Continuously analyzes the signal and adjusts for optimum picture quality.

Manual Tracking Control (to reduce picture noise)

Use during Playback and Slow Motion mode to reduce picture noise. Press CH (TRACKING) / on the remote control or on DECK until the picture clears up. To return to Auto Tracking, press POWER off, then on again a few seconds later.

V-Lock Control (to reduce picture jitter)

In Still mode, CH (TRACKING) / operate as a V-Lock control.

Initial Setup (Connection)

DVD / VCR

Important Safeguards and Precautions ............................... 2, 3

Before Using ...............................................................................4

DECK & Cassette Information .............................................. 6 , 7

Location of Controls .......................................................... 8 ~ 10

On Screen Displays / Light-up Indicators............................... 11

Connections ..................................................................... 12 ~ 15

Initial Setup for Basic Connections

Basic Operation

VCR

Reset Language, Channels, Clock, VCR’s Output Channel ........ 18, 19

Playback/ Record on a Tape.............................................. 20, 21

DVD

Basic DVD Operation ......................................................... 22, 23

VCR Operation

Timer Recording ................................................................. 24, 25

MTS Broadcast/ VHS Hi-Fi Stereo System ....................... 26, 27

Multi-Brand Control Feature .............................................. 28, 29

Tape Operation (Search System) .......................................... 30 ~ 32

Special VCR Features ........................................................ 33, 34

Copying Your Tapes (Dubbing) ............................................................ 35

(Ready to Play) ............. 16, 17

Initial Setup Basic Operation VCR Operation DVD Operation For Your Information

DVD Operation

Disc Operation .................................................................. 36 ~ 41

DVD-RAM Operation (DVD-RAM only) ....................................42, 43

DVD Operation using On-Screen Displays .................... 44 ~ 48

MP3/JPEG Playback Operation ....................................... 49 ~ 51

Settings for DVD Operation ............................................. 52 ~ 55

Language Code List ................................................................. 56

For Your Information

Warning and Instruction Displays........................................... 57

Before Requesting Service................................................ 58, 59

Limited Warranty ................................................................ 60, 61

Customer Services Directory .................................................. 61

Spanish (Español) Quick Use Guide............................... 62 ~ 69

Index .................................................................................... 70, 71

DECK & Cassette Information

Prevent Accidental Tape Erasure

Break off the tab to prevent recording.

Record Tab

Screw driver

To record again

Cover the hole with cellophane tape.

Disc formats supported by this DECK

DECK can play back discs bearing any of the following marks:

Logo Disc type

DVD-RAM (Version 1.1 of the Video Recording Format a unified video recording standard)

DVD (DVD-Video)

DVD-R (DVD-Video formatted discs [finalized])

Video CD

CD (CD-DA) CD-R/CD-RW

• CD-DA format

• MP3/JPEG file

and finalized.*

[Discs Played 8cm (3") or 12cm (5")] *A process that allows play on compatible equipment.

Discs which cannot be played

• DVD with Region No. other than “1” or “ALL”

• PAL discs, DVD-ROM, DVD-Audio, DVD-RW, DVD+R, DVD+RW, CD-ROM, CDV, CD-G, CVD, SVCD, SACD, CD-TEXT, Divx Video Disc, Photo-CD and MPEG4 Video Disc

Notes

• Do not use irregularly shaped discs (e.g. heartshaped), as these can damage the unit.

• It may not be possible to play CD-R, CD-RW, DVD-R and DVD-RAM in all cases due to the type of disc or condition of the recording.

For assistance, please call : 1-800-211-PANA(7262) or, contact us via the web at:http://www.panasonic.com/contactinfo

DVD-RAM discs

DVD-RAM discs must meet the following conditions for this unit to be able to play them.

Type

Capacity

• Remove TYPE 2 and 4 discs from their cartridges

before use, then return them when you are finished. Read the instructions for the disc carefully.

• Some parts of the disc, for example where one program

ends and another begins, may not play smoothly.

• Non-cartridge discs

• Discs that can be removed from their cartridges (TYPE 2 and 4)

• 12 cm (5”) 9.4 GB (double-sided) and 4.7 GB (single-sided)

• 8 cm (3”) 2.8 GB (double-sided)

Disc Handling

Handling precautions

• Sticking a label on the disc may impair DVD-R playback.

• Do not attach sticker to discs. (Do not use discs with exposed adhesive from tape or left over peeled-off stickers.)

• Only hold disc by edges as shown below. Fingerprints, dirt and scratches can cause skipping and distortion.

• Do not write on label side of disc.

• Never use record cleaning sprays, benzine, thinner, static electricity prevention liquids, or any other solvent.

• Do not try to close disc tray when disc is not properly placed.

To clean disc surface

With a soft, damp (water only) cloth, gently wipe from the center hole to the outer edge as shown below. (Wiping in a circular pattern will scratch the surface.)

• DVD-RAM, DVD-R : Clean only with the DVD-RAM disc cleaner available. Never use cloths or cleaners for CDs etc.

If disc is brought from a cold to a warm environment, moisture may form on the disc

Wipe away moisture with a soft, dry, lint-free cloth before using disc. (See above.)

Improper disc storage

Discs could be damaged if stored or left in areas:

• exposed to direct sunlight.

• that are humid or dusty.

• near heat (i.e. heater, radiator, etc.).

Disc tray

Disc

Specifications

Power Source: 120 V AC, 60 Hz Power Consumption: Power On: Approx. 22 watts, Power Off: Approx. 0.9 watts Video Signal: EIA Standard NTSC color Video Recording System: 4 rotary heads helical scanning system Audio Track: 1 track (Normal), 2 channel (Hi-Fi Audio Sound) Tuner Broadcast Channels: VHF 2 ~ 13, UHF 14 ~ 69 CABLE Channels: Midband A through I (14 ~ 22), Superband J through W (23 ~ 36)

Input/Output Terminal: Audio/Video Line Input/Output, RF Input/Output Input Terminal: Audio/Video Line Input (Front) Output Terminal: S-Video Output (DVD only), Component Video Output (DVD only)

Operating Temperature: 5 °C ~ 40 °C (41 °F ~ 104 °F) Operating Humidity: 10 % ~ 75 % Weight: 3.7 kg (8.2 lbs.) Dimensions: 430 (W) x 93 (H) x 255 (D) mm

Discs Played (1) DVD-Video Disc 5” (12 cm) single-sided single-layer

DVD-RAM Disc 5” (12 cm) 9.4 GB (double-sided) and 4.7 GB (single-sided)

(2) Compact Disc 5” (12 cm) disc

(CD-DA, Video CD) 3” (8 cm) disc (CD-R/CD-RW, MP3, JPEG)

Digital Audio Output: Digital Optical Connector Pickup: Wavelength : 655 nm (DVD), 790 nm (Video CD/CD)

Note: Designs and specifications are subject to change without notice.

Hyperband AA ~ EEE (37 ~ 64), Lowband A-5 ~ A-1 (95 ~ 99) Special CABLE channel 5A (01), Ultraband 65 ~ 94, 100 ~ 125

Audio Output 2 (L), (R)

16-15/16” (W) x 3-11/16” (H) x 10-1/16” (D) inch

5” (12 cm) single-sided double-layer 5” (12 cm) double-sided double-layer (one layer per side) 3” (8 cm) single-sided single-layer 3” (8 cm) single-sided double-layer 3” (8 cm) double-sided double-layer (one layer per side)

3” (8 cm) 2.8 GB (double-sided)

Laser power: CLASS II

Initial Setup

Definition of Terms (DVD)

Angle: Some DVD discs feature scenes simultaneously shot from different angles.

Chapter Number:Titles are subdivided into numbered sections. You can quickly search for

DVD: A high-density optical disc on which high-quality pictures and sound have been

Playback Control:With Video CD (version 2.0), scenes or information may be selected for viewing or

Subtitles: Written dialogue which appears at the bottom of the screen. Time Number: The elapsed play time from the start of a disc or title. Use to quickly find scenes.

Title Number: For DVD discs with two or more titles, the title is numbered as title 1, title 2, etc. Track Number: Numbers assigned to tracks on Video CDs and CDs to allow specific tracks to be

Video CD: CD containing picture and sound with same quality level as video tape.

U.S. Patent Nos. 4,631,603; 4,577,216; 4,819,098; 4,907,093; 5,315,448; and 6,516,132.

This product incorporates copyright protection technology that is protected by U.S. Patents and other intellectual property rights. Use of this copyright protection technology must be authorized by Macrovision, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision. Reverse engineering or disassembly is prohibited.

The ANGLE button can be used to view the scene from different angles.

a favorite scene using these numbers.

digitally recorded. DVD incorporates video compression technology (MPEG II) and high-density recording technology which allow entire movies to be recorded with incredible playback quality.

listening from an interactive menu that appears on the TV screen.

(May not work with some discs.)

quickly located.

This DECK also supports Video CDs with playback control (version 2.0).

Location of Controls

Remote Control

EJECT

OPEN/ CLOSE

pp. 20,

POWER

NUMBER keys

ADD/DELETE

pp. 19,

38, 40

CLEAR

ACTION

pp. 18

, 52

SET

VCR mode

p. 28

STOP

pp. 20,

REWIND

SLOW-

pp. 20,

FAST FORWARD

SEARCH/SLOW+

pp. 20,

PAUSE

pp. 20,

ANGLE

. 37

SUB TITLE

. 36

TITLE DIRECT NAVIGATOR

. 41, 42

STILL

Bold: VCR Function /

Italic

DVD Function

Bold Italic:VCR and DVD Functions

/ Normal: Others

TRACKING/V-LOCK

CHANNEL

VOLUME+/

MENU/ PLAY LIST

Virtual Surround Sound (V.S.S.)

TAPE POSITION/STATUS

AUDIO

(SAP / Hi-Fi)

VCR/TV

p. 21

TV mode

p. 28

. 41, 43

pp. 4, 21,

SELECT

DVD mode

PLAY

pp. 20,

SKIP+

SKIP-

. 23

ENTER

. 23,

ZOOM

. 37

p. 32

pp. 27,

INPUT

p. 35

DISPLAY

p. 11,

RECORD

p. 21

SPEED

p. 21

EJECT button: When this button is pressed in VCR mode, the tape is ejected.

For assistance, please call : 1-800-211-PANA(7262) or, contact us via the web at:http://www.panasonic.com/contactinfo

This button is inoperative if pressed during recording. If pressed in DVD mode, the disc tray opens or closes.

RETURN

COMMERCIAL SKIP

COUNTER RESET

. 22,

ZERO SEARCH

p. 30

PROGRAM

p. 24

Front View of DECK

Bold: VCR Function

Italic

DVD Function

Bold Italic

Normal: Others

PLAY

p. 20

VCR and DVD Functions

If the disc cannot be removed...

First, unplug DECK. Then, prepare a rigid wire (e.g. an extended paper clip) and, applying moderate force, insert it straight into the hole at the base of the tray. The tray will eject a little. Now, pull the tray all the way out and remove the disc.

Initial Setup

STOP/EJECT

p. 20

POWER

Audio/Video Input Connector 2 (LINE 2)

REC

p. 21

CHANNEL / TRACKING/V-LOCK

pp. 4, 21

p. 35

Cassette Compartment

Remote Sensor

Reset All Memory Functions

Light-up

Indicators

p. 11

Over 2 inches

Disc Tray

OPEN/CLOSE

FAST FORWARD

REWIND

PLAY

STOP

SKIP

p. 20,

SKIP

p. 20,

Returns to factory setting. Use if relocating DECK, or if Initial Setup needs to be redone.

• Make sure a tape is not inserted in the DECK.

Turn DECK Power on.

Press and hold both VCR PLAY

and CHANNEL on the DECK for more than 5 seconds.

• The power shuts off. Perform “Initial Setup (Ready to Play)”

on page 16.

Location of Controls (continued)

Rear View of DECK

AC Power Plug

• While plugged into an AC outlet, this DECK consumes 0.9 W of electrical power in off mode.

Component Video Output Connector (Y, P (DVD Only)

Optical Digital Audio Output Connector (DVD Only)

S-Video Out Connector (DVD Only)

pp.

10, 13

Bold: VCR Function

Bold Italic

VCR and DVD Functions

VHF/UHF Antenna Output Terminal p.12

VHF/UHF Antenna Input Terminal p. 12

Video Output

, PR)

Connector

•

Audio Output 2 Connector (L/R)

Italic:DVD Function

Video Input Connector p. 35

•

Audio Input Connector (L/R) p. 35

Audio Output 1 Connector (L/R)

The following table shows the status of the output jacks when in VCR or DVD mode.

Video Output Audio Out 1 Audio Out 2

VCR

DVD

• PROG functions on the remote are not available when using Component Video Output and

Note

S-VIDEO OUT. Please set TV to either RF INPUT or VIDEO INPUT, and then press PROG.

YES YES

Component Video Output

N/A

S-VIDEO OUT

N/A

YES

To enjoy PROGRESSIVE SCAN video

(1). Connect

(See p. 13.)

(2). When PROGRESSIVE OUT is set to “ON” in the DVD Main Menu (p. 55), a Progressive Scan

signal is output from the

Notes

• The screen may shift off-center when using progressive output. Please adjust the screen

position if this occurs. (Refer to your TV manual.)

• If the television is not progressive compatible, a progressive scan picture is not available.

Connect the Video Output or S-Video Output connector (see p. 12, 13) and set PROGRESSIVE OUT to “OFF” in the DVD Main Menu. (See p. 55.)

For assistance, please call : 1-800-211-PANA(7262) or, contact us via the web at:http://www.panasonic.com/contactinfo

Component Video Output

Component Video Output Connector

to the component video input terminals of a television.

On Screen Displays / Light-up Indicators

On Screen Displays (VCR)

Function & Channel Displays

When a function button is pressed, e.g. PLAY, or you change channels, and also if a cassette is inserted, a 5-second display appears.

VCR Status & Clock Displays To display or remove screen shown at right,

➛➛

➛ press DISPLAY.

➛➛

Note

• For on Screen Displays in DVD mode, see p. 44.

Cassette inserted (Rec Time Remaining

is displayed in OTR mode, e.g.“0:25”. See p.21.)

Broadcast Audio Being Received (See pp. 26, 27.)

Light-up Indicators

Light-up indicators allow easy confirmation of current DECK function status.

Blank Tape/ No Signal Indications

Whenever a blank section of a tape comes up in Play mode, or when the selected channel has no broadcast signal with Weak Signal Display Feature (p. 33) set to OFF, the TV screen will turn solid blue.

Function Status

Current Time Channel

Counter

Tape Speed

(See p. 4.) Date (When clock is set, a 5-second

display appears.)

Timer Indicator

Lights up when DECK is set for Timer Recording, or when One Touch Recording (OTR) is used. Flashes when Timer Recording is set, but a tape has not been inserted into DECK and when a power interruption occurs during Timer Programming.

Initial Setup

VCR mode Indicator

Lights when output selection is VCR mode. Flashes in Auto Clock Set or Channel Auto Set.

VCR REC Indicator

Lights up during recording. Flashes in Rec. Pause mode.

<Light-up combination example>

Light-up Indicator Function Status

VCR +

VCR

DVD

VCR

PLAY

➛➛

➛

➛➛

➛

➛➛

PLAY

REC

TIMER

PLAY

REC

TIMER

REC

➛➛

➛

➛➛

TIMER PLAY

➛➛

➛

➛➛

➛

➛➛

➛

➛➛

REC VCR

PLAY Indicator

Lights during playback in either VCR mode or DVD mode. Flashes in Still, Frame by Frame, or Slow mode.

VCR playback in progress [See p. 20]

VCR recording in progress [See p. 21]

VCR timer setting in progress [See pp. 24, 25]

VCR Timer Recording in progress [See pp. 24, 25]

DVD playback in progress [See pp. 22, 23]

VCR fast forward in progress [See p. 20]

VCR rewind in progress [See p. 20]

DVD mode Indicator

Lights when output selection is DVD mode.

Connections

Basic Connections

• If your TV has AUDIO and VIDEO IN terminals, connect them to DECK for higher

quality picture and sound.

• You can enjoy stereo sound even if your TV is not stereo by connecting a stereo

amplifier to DECK.

• Connect DECK and TV with an RF Coaxial Cable a (supplied) or an AV Cable (not supplied) as shown in the figure below.

■ ■

■ DSS Receiver DECK TV

■ ■

DSS Receiver

OUT

DVD/VCR DECK

IN FROM ANT.

IN 1

OUT

VIDEO

AUDIO

VHF/UHF

OUT TO TV

■ ■

■ DECK TV

■ ■

Antenna or Cable

1 Disconnect antenna or cable from TV

and connect to DECK.

2 Connect DECK to TV with RF Coaxial Cable.

■ ■

■ Cable Box DECK TV

■ ■

IN OUT

AUDIO IN

Cable Box

RF COAXIAL CABLE

(supplied)

VHF/ UHF

VIDEO

AV CABLE

When using “Nut type” RF coaxial cables, tighten with fingers only. Overtightening may damage terminals.

Note to CABLE system installer

This reminder is provided to call the CABLE system installer’s attention to Article 820-40 of the NEC in USA (and to the Canadian Electrical Code in Canada) that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical.

For assistance, please call : 1-800-211-PANA(7262) or, contact us via the web at:http://www.panasonic.com/contactinfo

(not supplied)

Other Connections

■ ■

■ With a Cable Box (DECK

■ ■

DVD/VCR DECK

IN FROM ANT.

IN 1

OUT

VHF/UHF

OUTTO TV

■■

■

Connect With Two Cable Boxes

■■

ANT or CATV

Cable Box

DVD/VCR DECK

ANT

CATV

Cable Box

OUT

2-Way Splitter

OUT 1

OUT 2

IN 1

OUT

Cable Box

OUTIN

Cable Box TV)

OUT

VHF/

OUTIN

UHF

IN FROM ANT.

VHF/UHF OUT TOTV

A/B Switch

IN 2IN 1

R L

AUDIO

VIDEO

OUT

VHF/ UHF

AUDIO

VIDEO

• view any (including scrambled) channel.

• use Remote Control to select channels without using Multi-brand control feature.

• record and view both scrambled and unscrambled channels if additional equipment is added. This connection requires: two converter boxes, an A/B switch, and a 2-way splitter.

You CannotYou Can

• record scrambled channels.

You CannotYou Can

• view a channel other than the one selected for any type of recording.

• set a Timer recording of a channel unless you select it on the Cable Box.

Connections For DVD Only (enjoying higher picture quality)

Connect AUDIO OUT2 (L, R) to the AUDIO IN (L, R) of the TV. (audio input for COMPONENT or

S-VIDEO mode). If your TV has COMPONENT VIDEO INPUT, connect to COMPONENT VIDEO OUT.

If your TV does not have COMPONENT VIDEO INPUT but has S-VIDEO INPUT, connect to S-VIDEO OUT.

When in DVD mode, set your TV to either COMPONENT VIDEO IN or S-VIDEO IN.

Notes

• You can watch DVDs through the S-VIDEO or COMPONENT VIDEO, VHF/UHF OUT TO TV, and VIDEO OUT connections to your TV. The VCR and TUNER pictures are available only from the VIDEO OUT and VHF/UHF OUT TO TV connections to your TV.

• PROG functions on the remote are not available when using S-VIDEO OUT and COMPONENT Video Output. Please set TV to either RF INPUT or VIDEO INPUT, and then press PROG.

• TV must have capability to accept and display a progressive scan signal to use PROGRESSIVE mode. Consult your TV operating instructions.

DVD/VCR DECK

DVD OUTPUT

S-VIDEO OUT

COMPONENT

VIDEO OUT

P R

AUDIO OUT2

AUDIO

VIDEO

S-VIDEO IN

From DECK’s

A/V OUTPUT

Initial Setup

Connections (continued)

Audio Connections

Ready Checklist

Turn down the volume, then turn DECK, as well as other equipment to be connected, off before proceeding with connection. Do not block ventilation holes of any of the equipment and arrange them so that air can circulate freely. Read through the instructions before connecting other equipment. Ensure that you observe the color coding when connecting audio and video cables.

■ Connecting Amplifier (2ch stereo system) [Analog connection]

DVD/VCR DECK

Speaker

AUDIO OUT2

L R

Enjoying digital audio output from the digital audio output connector

Notes on audio output from the optical digital audio output connector

Disc

DVD-Video

Sound recording format

Dolby Digital

Linear PCM (48/96 kHz 16/20/24 bit)

DTS

DVD-RAM

Dolby Digital

Linear PCM(48 kHz/16 bit)

Video CD CD MP3

*1 The type of audio output from the connector can be selected by the Settings for DVD Operation.

(See p. 53.)

*2 When “LPCM(DVD)” is set to OFF in the DVD Main Menu, only 48 kHz sampling/16 bit is ouput.

When set to ON, sampling of sound quality greater than 48 kHz/16 bit is reduced to 48 kHz/16 bit. (See page 53.)

MPEG1 Linear PCM MP3

For your reference:

• Dolby Digital is a digital sound compression technique developed by the Dolby Laboratories Licensing Corporation. Supporting 5.1-channel surround sound, as well as stereo (2-channel) sound, this technique enables a large quantity of sound data to be efficiently recorded on a disc.

• Linear PCM is a signal recording format used in CDs. While CDs are recorded in 44.1 kHz/16 bit, DVDs are recorded in 48 kHz/16 bit up to 96 kHz/24 bit.

• If you have a Dolby Pro Logic Surround decoder, you will obtain the full benefit of Pro Logic from the same DVD movies that provide full 5.1 channel Dolby Digital soundtracks, as well as from titles with the Dolby Surround mark. For information on Panasonic or Technics Dolby Pro Logic Surround Sound Decoders please contact your local dealer.

Manufactured under license from Digital Theater Systems, Inc. US Pat. No’s. 5,451,942, 5,956,674, 5,974,380, 5,978,762, 6,487,535 and other US. and world-wide patents issued and pending. “DTS” and “DTS 2.0 + Digital Out” are trademarks of Digital Theater Systems, Inc. Copyright 1996, 2003 Digital Theater Systems, Inc. All Rights Reserved.

Manufactured under license from Dolby Laboratories. Dolby and the double-D symbol are trademarks of Dolby Laboratories.

For assistance, please call : 1-800-211-PANA(7262) or, contact us via the web at:http://www.panasonic.com/contactinfo

Optical digital audio output from connector

Dolby Digital bitstream (1 - 5.1 ch) or PCM (48 kHz sampling/16 bit only)*

Linear PCM (2 ch) (48 kHz sampling/16 bit only)*

Bitstream or PCM (48 kHz sampling/16 bit only)* Dolby Digital bitstream (1 - 5.1 ch)

or PCM (48 kHz sampling/16 bit only) Linear PCM (2 ch) PCM (44.1 kHz sampling) Linear PCM (44.1 kHz sampling)

PCM (It depends on the MP3 file)

Amplifier

AUDIO IN

R L

Speaker

■ Connecting Amplifier (5.1 ch Surround system) [Digital connection] DECK Dolby Digital Decoder Amplifier Speaker

DECK DTS (Digital Theater Systems) Decoder Amplifier Speaker

When DVDs recorded in Dolby Digital or DTS are played, Dolby Digital bitstream or DTS bitstream is output from the DECK OPTICAL digital audio output connector. When DECK is connected to a Dolby Digital decoder or DTS decoder, you can enjoy theater-quality audio in your home. [An optical digital audio cable (optional) is required when an optional Dolby Digital decoder or DTS decoder is used.]

Notes on connecting an optical digital audio cable (optional)

• Remove the attached cap, and firmly connect the cable to the connector.

Initial Setup

Surround Speaker

[5.1ch Surround system]

Center Speaker

Surround Speaker

DVD/VCR DECK (Rear)

Optical Digital Audio Cable (optional)

Caution for optical digital audio output connector:

• When connecting an amplifier (with an Optical Digital Input Connector) which does not contain the Dolby Digital or DTS decoder, be sure to select “PCM” at “Dolby Digital” and “PCM” at “dts” of the Settings for DVD Operation “Audio Output” (see p. 53). Otherwise, any attempt to play DVDs may cause such a high level of noise that it may be harmful to your ears and damage your speakers.

• When a Dolby Digital/DTS decoder is connected, please select “Bitstream” at “dts” or “Dolby Digital” of the Settings for DVD Operation “Audio Output”. If “PCM” is selected, there will be stereo sound. (See p. 53.)

• Video CDs and CDs can be played as usual.

Note

• Some DTS decoders which do not support DVD-DTS interface may not work properly with DECK.

Decoder with Dolby Digital /DTS processing (optional)

To Optical Digital Audio Input Connector

Front Speaker

Amplifier

Front Speaker

Subwoofer

Initial Setup for Basic Connections (Ready to Play)

Before doing Initial Setup

Turn TV on.

See connections RF Coaxial Cable Connection and AV Cable Connection on page 12.

ÖSet TV to channel 3.

ÖSet TV to VIDEO.

[DECK

• Go to “Initial Setup (Ready to Play).” (See below.)

[Cable Box

• Turn on Cable Box and set it to your Public Broadcasting Station (PBS) channel

• If you use a DSS Receiver, it must be turned off.

Initial Setup (Ready to Play)

Press VCR on remote for VCR mode.

Plug DECK Power Cord into AC wall outlet. DECK comes on and auto channel and clock set starts.

• If screen below does not appear, check DECK - TV connection and, if TV is tuned to

• To change VCR’s output channel, please see “VCR’s Output Channel” on page 19.

➛➛

➛ TV]

➛➛

➛ DECK

➛➛

in your time zone.

channel 3, try switching it to channel 4.

➛➛

➛ TV], [DSS

➛➛

Plug VCR Power plug into an AC wall outlet.

➛➛

➛ DECK

➛➛

➛ TV]

➛➛

Notes

• Function buttons are void during Initial Setup.

• To eject a tape during Auto Set, press EJECT on remote or STOP/EJECT twice on DECK. Then make settings manually. (See p. 18.)

• If Auto Clock Set takes more than 30 minutes, press STOP and perform settings manually. (See p. 18.)

Continued on next page...

For assistance, please call : 1-800-211-PANA(7262) or, contact us via the web at:http://www.panasonic.com/contactinfo

*Important: If a remote control button does not work when pressed,

press the VCR button on the remote and try the button again.

EJECT

ACTION

SELECT

SET

VCR

Settings are made automatically. When complete, this screen appears.

If “AUTO CLOCK SET IS INCOMPLETE” appears, manually set clock (below).

Manual Clock Set

If Auto Clock Set was incomplete.

Press ACTION* on remote to display CLOCK screen.

Initial Setup

STOP/EJECT

Press In the same manner, select and set the date,

year, time, and DST (Daylight Saving Time).

Press ACTION to start clock and exit.

to select the month and SET to set.

Reset Language, Channels, Clock,

Press ACTION*

to display MENU.

Language

1) Press to select

language item.

2) Press SET repeatedly to

change language item as shown below.

For Spanish

For French

➡

• PROGRAM functions are not available when using COMPONENT Video Output and S-VIDEO OUT. Please set TV to either RF INPUT or VIDEO INPUT, and then press PROGRAM.

Channels

1) Press to select

“SET UP CHANNEL,” and press SET.

2) Press to select

“ANTENNA,” then press SET to set your antenna system (“TV” or “CABLE.”)

3) Press to select

“AUTO SET,” then press SET.

• If you use a Cable Box, set it to the PBS channel in your time zone.

Clock

1) Press to select

“SET CLOCK,” and press SET.

2) Press to select “MANUAL,” and press SET. (For Auto Clock Set, select “AUTO CLOCK SET.”)

(“TIME ZONE ADJUST”

appears only when auto clock is set.)

3) Press and to

select, then set the date, time, and DST (Daylight

• After Channel Auto Set

For English

3) Press ACTION to exit.

For assistance, please call : 1-800-211-PANA(7262) or, contact us via the web at:http://www.panasonic.com/contactinfo

is finished, Auto Clock Set will be performed.

Saving Time).

4) Press ACTION to start

Clock and exit this mode.

VCR’s Output Channel

*Important: If a remote control button does not work

Time Zone Adjust

(Only when Auto Clock is set.)

1) Press to select

“SET CLOCK,” and press SET.

2) Press to select

“TIME ZONE ADJUST,”

and press SET to subtract or add hour(s) as necessary.

3) Press ACTION.

• “TIME ZONE ADJUST” returns to “0” if clock is set manually.

when pressed, press the VCR button on the remote and try the button again.

VCR’s Output Channel

1) Press to select

“VCR’S OUTPUT CH.,” and press SET.

2) Press SET.

3) Press ACTION.

➡

After 3 seconds

POWER NUMBER

keys CH /

ADD/DLT ACTION SELECT

SET VCR

Add or Delete a Channel

To add channel: Select channel with NUMBER keys

and press ADD/DLT.

To delete channel: Select channel with CH / or

NUMBER keys and press ADD/DLT.

DST (Daylight Saving Time)

Basic Operation

• To Make Corrections, repeat steps 1) ~ 3).

DECK auto adjusts clock for DST. (p. 17.)

Spring (First Sunday in April)

DST:ON

Autumn (Last Sunday in October)

DST:ON

• If your area does not observe

• Keep these time changes in mind

➛➛

➛ Sets clock ahead one hour.

➛➛

➛ Turns clock back one hour.

➛➛

Daylight Saving Time, select DST:OFF.

when programming DECK for timer recordings.

Playback/ Record on a Tape

Ready Checklist

All connections are made. (pp. 12 ~ 15) TV and DECK are plugged in. TV is on and tuned to CH 3, 4, or VIDEO. Remote is in VCR mode. (Press VCR.)

➛ ➛

(

➛ The VCR mode Light-up Indicator lights on DECK)

➛ ➛

Playback a Tape

Insert a tape.

• DECK power comes on. If Auto VCR/TV (see p. 34) is set to “OFF,” press VCR/TV on the remote for VCR mode.

Press PLAY* to play a tape.

• If tape has no rec. tab (p. 6), auto play begins.

• The PLAY Light-up Indicator lights on DECK.

Special Features During Play

Forward/Reverse Scene Search

➛➛

➛ Press FF/SLOW+ or REW/SLOW-.

➛➛ ➛➛

➛ Press PLAY to release.

➛➛

After search has begun, each additional press of FF/SLOW+ or REW/SLOW- changes speed as shown below. [SP] : Approx. 5X ↔ Approx. 7X

[SLP] : Approx. 11X

Notes

• Picture interruption may occur with some TVs.

• FF and REW search speed may vary depending on current tape position.

• After 10 minutes in search mode, VCR returns to Play mode to protect the tape and the video heads.

Still (Freeze) Picture

➛➛

➛ Press PAUSE/STILL.

➛➛ ➛➛

➛ Press PLAY to release.

➛➛

Frame by Frame Picture

➛➛

➛ Press PAUSE/STILL in Still mode.

➛➛ ➛➛

➛ Press PLAY to release.

➛➛

Slow Motion Picture

➛➛

➛ Press FF/SLOW+ (increase speed) or

➛➛

REW/SLOW- (decrease speed) in Still mode.

➛➛

➛ Press PLAY to release.

➛➛

↔ Approx. 21X

EJECT

VCR

FF/ SLOW+

REW/ SLOW-

PAUSE/ STILL

REC

Notes

• These features work best in SP or SLP mode.

• The sound will be muted.

• To reduce picture noise, see “Manual Tracking Control” on page 4.

• After 3 minutes in Still or Slow mode, VCR stops to protect the tape and the video heads.

VCR/TV

CH /

DVD

PLAY

STOP

SPEED

Playback using DECK buttons

Press PLAY.

Insert a tape.

Press STOP to stop a tape.

Press REW/SLOW- or FF/SLOW+ in Stop

mode to rewind or fast forward a tape. Press EJECT on remote,

or STOP/EJECT on DECK to eject a tape.

For assistance, please call : 1-800-211-PANA(7262) or, contact us via the web at:http://www.panasonic.com/contactinfo

Light-up Indicators

Press STOP/EJECT to stop and/ or eject a tape.

*Important: If a remote control button does not work when pressed,

press the VCR button on the remote and try the button again.

Record on a Tape

Insert a tape with a record tab (p. 6).

• DECK power comes on. If Auto VCR/TV (see p. 34) is set to “OFF,” press VCR/TV on the remote for VCR mode.

Press CH , or NUMBER keys

to select the channel.

• If channel number is over 100, first press 100 key then the other 2 digits.

• For “LINE” input, see p. 35.

Press SPEED

to select the record speed (p. 4).

SP = Standard Play SLP = Super Long Play

Press REC

to start recording.

(The VCR REC Light-up Indicator lights on DECK),

• To edit out unwanted scenes, press PAUSE/STILL to pause, and again to resume recording.

• You cannot view another channel during recording.

Press STOP

to stop recording.

One Touch Recording (recording in progress),

➛➛

➛ press REC repeatedly to set the recording length

➛➛

(30 min. ~ 4 hours) (see right).

• DECK shuts off after the preset record length.

Record one station, watch another,

➛➛

➛ press VCR/TV on the remote

➛➛

(change to TV mode),

➛➛

➛ select channels at TV (recording continues).

➛➛

Select Channels at DECK

(In Stop or Rec. Pause mode)

➛➛

➛ press VCR/TV on the remote

➛➛

(change to TV mode),

➛➛

➛ select channels at DECK.

➛➛

Play a disc while recording a tape.

➛➛

➛ insert a disc during recording,

➛➛ ➛➛

➛ press

➛➛

DVD

, and then press

PLAY

This video recorder, equipped with HQ (High Quality) system, is compatible with existing VHS equipment. Only use tapes with the mark. Only tapes tested and inspected for use in 2, 4, 6, and 8 hour machines are recommended.

Note

Remove loose or peeling labels from tapes to prevent tape jam.

Normal Rec

Press REC repeatedly

0:30 1:00

1:302:003:004:00

Record using DECK buttons

Press REC to start recording.

Insert a tape.

Basic Operation

Notes

• It is not possible to record from DVD/ Video CD/ CD to VHS tape using DECK.

• Watching one channel and recording another is not possible when using Cable Box or DSS Receiver.

• After 5 minutes in Pause mode, DECK stops to protect a tape and video heads.

Select

Channel.

Press STOP/EJECT to stop.

Light-up Indicators

Basic DVD Operation

Ready Checklist

All connections are made. (pp. 12 ~ 15) DECK is plugged in. If DECK is connected to an audio amplifier,

turn the stereo system’s power on.

OPEN/ CLOSE

POWER

NUMBER keys

SELECT

SET FF/

SLOW+ REW/

SLOWPAUSE/

STILL TITLE

STOP DVD

PLAY

SKIP+ SKIP

VSS

RETURN

If an interactive DVD*1 or a Video CD with playback control*2 is used and TITLE MENU appears, go to step 4.

Press

DVD

• The DVD mode Light-up Indicator lights on DECK.

• If a disc is already inserted, go to step 3. (Depending on the disc, playback may start automatically.)

Press

and then place a disc into the disc tray.

Press

Disc tray closes automatically.

to select DVD mode.

OPEN/CLOSE

• Hold disc by its edges

1 2

PLAY

to start playing.

• The PLAY Light-up Indicator lights on DECK.

• You may also close tray by

pressing

• Data reading time differs with each disc.

only (p. 6) with printed side up and use guides to place into tray.

Use 3” (8 cm)

or 5” (12 cm) disc.

DVD-RAM ➡ see p. 42

OPEN/CLOSE

TITLE MENU

Cats

Samurai

Friend

Music

Operation using DECK buttons

3, 7

Press

POWER.

*1Interactive DVD...

May include multiple camera angles, stories, etc.

*2Video CD with playback control...

Particular scenes or information can be interactively selected from a menu that appears on the screen.

For assistance, please call : 1-800-211-PANA(7262) or, contact us via the web at:http://www.panasonic.com/contactinfo

Insert a disc.

Press OPEN/CLOSE.

Press PLAY.

Press STOP.6

TITLE MENU

Using NUMBER keys starts play automatically.

The number of available titles varies with each disc.

<Input

Press previous menu screen.

• SKIP function not available with all discs.

To return to menu (play stops)

Press Press

Cats

Samurai

Friend

Music

1 digit number 1 •••• 1

Example>

SKIP+

Please refer to disc jacket for operation information.

TITLE, MENU, RETURN

Press

2 digit number 12 ••• 10 ➛ 1 ➛ 2

| or

. (Video CD)

STOP

OPEN/CLOSE

Press or

NUMBER keys

below) to select title, and press

PLAY

to start playing.

• Pressing is not necessary when using

NUMBER keys.

SKIP-

| to go to next or

RETURN

to stop playing.

. (DVD)

to eject the disc.

SET

(see

PLAY

+ 50 hidden pages

Panasonic PV-D4735S User Manual

Important Safeguards and Precautions

Before Using

Table of Contents

Location of Controls

On Screen Displays / Light-up Indicators

Connections

Initial Setup for Basic Connections (Ready to Play)

Playback/ Record on a Tape

Basic DVD Operation