Panasonic PV-D4734SK User Manual

DVD/VCR DECK

Operating Instructions

(Connection)

Initial Setup

Model No.

Connections and Initial Setup Procedures are on pages 12 to 17.

PV-D4734S-K

Operation

Basic

Operation

VCR

Operation

DVD

MULTI FORMAT PLAYBACK

Ability to play back may depend on recording conditions.

As an ENERGY STAR ® Participant, Panasonic has determined that this product or product model meets the ENERGY STAR guidelines for energy efficiency.

Please read these instructions carefully before attempting to connect, operate or adjust this product. Please save this manual.

For assistance, please call : 1-800-561-5505 or visit us at www.panasonic.ca

D4734S-K P1-25 (040202).p65 2004/02/02, 15:131

Information

For Your

LSQT0828 A

Important Safeguards and Precautions

TO REDUCE THE RISK OF ELECTRIC SHOCK, FIRE, INJURY TO PERSONS OR DAMAGE TO THIS PRODUCT, READ AND RETAIN ALL SAFETY AND OPERATING INSTRUCTIONS. HEED ALL WARNINGS IN THE MANUAL AND ON THE PRODUCT.

INSTALLATION

1 POWER SOURCE CAUTION

Operate only from a power source indicated on the unit or in this manual. If necessary, have your Electric Utility Service Company or Video Products Dealer verify the power source in your home.

2 POLARIZED OR GROUNDING PLUG

As a safety feature, this product comes with either a polarized power cord plug (one blade is wider than the other), or a three-

wire grounding type plug. POLARIZED PLUG CAUTION: This plug will only fit into an outlet one way. If you cannot fully insert the plug, try reversing it. If it still will not fit, have an electrician install the proper wall outlet. Do not defeat the safety feature by tampering with the plug. GROUNDING PLUG CAUTION: This plug will only fit into a three-hole grounding outlet. If necessary, have an electrician install the proper outlet. Do not defeat the safety feature by tampering with the plug.

3 POWER CORD

Make sure power cords are routed so that they are not likely to

have anything rest on them, roll over them, or be in the way of

walking traffic. If an extension cord is used, make sure it also

has either a polarized or grounded plug and that the cords can

be securely connected. Frayed cords, damaged plugs, and

damaged or cracked wire insulation are hazardous and should

be replaced by a qualified service technician.

Overloaded outlets and extension cords are fire hazards and

should be avoided.

4 DO NOT BLOCK VENTILATION HOLES

Ventilation openings in the cabinet release heat generated during

operation. If they are blocked, heat build-up inside the unit can

cause failures that may result in a fire hazard or heat damage to

cassettes or discs.

For protection, follow these rules:

a. Never cover ventilation slots or the unit while in use, or

operate the unit when placed on a bed, sofa, rug, or other soft surface.

b. Avoid built-in installation, such as a book case or rack,

unless proper ventilation is provided.

5 PLACEMENT: AVOID EXTREMELY HOT LOCATIONS OR

SUDDEN TEMPERATURE CHANGES

Do not place the unit over or near heater or radiator, in direct

sunlight, inside closed vehicles, in high temperature [over 104°F

(40°C)], or in over 75% humidity. If the unit is suddenly moved

from a cold place to a warm one, moisture may condense in the

unit and on the tape causing damage. Never subject the unit to

vibration, impact, or place it so that the surface is tilted as

internal parts may be seriously damaged.

6 TO AVOID PERSONAL INJURY

• Do not place unsecured equipment on a sloping surface.

• Do not place this unit on any support that is not firm, level, and adequately strong. The unit could fall causing serious injury to a child or adult and damage to the unit.

• An appliance and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the appliance and cart combination to overturn.

• Carefully follow all operating instructions and use the manufacturer's recommended accessories when operating this unit or connecting it to any other equipment.

1 SAFE ANTENNA AND CABLE CONNECTION

If an outside antenna or cable system is connected to the equipment, be sure the antenna or cable system is grounded so as to provide some protection against built up static charges and voltage surges. Part 1 of the Canadian Electrical Code, in USA Section 810 of the National Electrical Code, ANSI/NFPA 70, provides information with respect to proper grounding of the mast and supporting structure, grounding of the leadin wire to an antenna discharge unit, size of grounding conductors, location of antenna discharge unit, connection to grounding electrodes and requirements for the grounding electrode.

2 KEEP ANTENNA CLEAR OF HIGH VOLTAGE POWER LINES OR

CIRCUITS

An outside antenna system should be located well away from power lines, electric light or power circuits and where it will never come into contact with these power sources if it should happen to fall. When installing an outside antenna, extreme care should be taken to avoid touching power lines, circuits or other power sources as this could be fatal. Because of the hazards involved, antenna installation should be left to a professional.

If the unit has been in storage or moved to a new location, refer first to the INSTALLATION section of these safeguards.

1 KEEP THE UNIT AWAY FROM WATER OR MOISTURE OF ANY KIND. 2 IF EQUIPMENT IS EXPOSED TO RAIN, MOISTURE, OR STRONG

IMPACT, unplug the unit and have it inspected by a qualified service technician

before use.

3 DURING AN ELECTRICAL STORM

During a lightning storm, whether indoors or outdoors, or before leaving the unit unused for extended periods of time, disconnect all equipment from the power source as well as the antenna and cable system.

4 WHEN THE UNIT IS PLUGGED IN

• Never expose the unit to rain or water. DO NOT OPERATE if liquid has been spilled into the unit. Immediately unplug the unit, and have it inspected by a service technician. Fire and shock hazards can result from electrical shorts caused by liquid contact inside.

• Never drop or push any object through openings in the unit. Some internal parts carry hazardous voltages and contact can cause electric shock or fire hazard. Do not put any foreign object on the disc tray.

• Avoid placing the unit directly above or below your TV set as this may cause electrical interference. Keep all magnets away from electronic equipment.

5 USING ACCESSORIES

Use only accessories recommended by the manufacturer to avoid risk of fire, shock, or other hazards.

6 CLEANING THE UNIT

Unplug the unit. Then, use a clean, dry, chemically untreated cloth to gently remove dust or debris. DO NOT USE cleaning fluids, aerosols, or forced air that could over-spray, or seep into the unit and cause electrical shock. Any substance such as wax, adhesive tape, etc. may mar the cabinet surface. Exposure to greasy, humid, or dusty areas may adversely affect internal parts.

1 DO NOT SERVICE THIS PRODUCT YOURSELF

If, after carefully following the detailed operating instructions, this product does not operate properly, do not attempt to open or remove covers, or make any adjustments not described in the manual. Unplug the unit and contact a qualified service technician.

2 IF REPLACEMENT PARTS ARE REQUIRED

Make sure the service technician uses only parts specified by the manufacturer, or those having the same safety characteristics as the original parts. The use of unauthorized substitutes may result in fire, electric shock, or other hazards.

3 HAVE THE SERVICE TECHNICIAN PERFORM A SAFETY CHECK

After any service or repairs to the unit, request the service technician to conduct a thorough safety check as described in the manufacturer’s service literature to ensure that the unit is in safe operating condition.

OUTDOOR ANTENNA INSTALLATION

NEC - NATIONAL

ELECTRICAL CODE

ELECTRIC SERVICE EQUIPMENT

USING THE UNIT

SERVICE

GROUND CLAMP

ANTENNA LEAD IN WIRE

ANTENNA DISCHARGE UNIT (NEC SECTION 810-20)

GROUNDING CONDUCTORS (NEC SECTION 810-21)

GROUND CLAMPS

POWER SERVICE GROUNDING ELECTRODE SYSTEM (NEC ART 250, PART H)

D4734S-K P1-25 (040202).p65 2004/02/02, 15:132

Safety Precautions

To prevent fire or shock hazard, do not expose this equipment to rain or moisture.

To prevent electric shock, match wide blade of plug to wide slot, fully insert.

This symbol warns the user that uninsulated voltage

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK)

NO USER-SERVICEABLE PARTS INSIDE

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL

within the unit may have sufficient magnitude to cause electric shock. Therefore, it is dangerous to make any kind of contact with any inside part of this unit.

This symbol alerts the user that important literature concerning the operation and maintenance of this unit has been included. Therefore, it should be read carefully in order to avoid any problems.

CAUTION:

UNIT IS A CLASS I LASER PRODUCT. HOWEVER THIS UNIT USES A VISIBLE LASER BEAM WHICH COULD CAUSE HAZARDOUS RADIATION EXPOSURE IF DIRECTED. BE SURE TO OPERATE THE UNIT CORRECTLY AS INSTRUCTED.

WHEN THIS UNIT IS PLUGGED TO THE WALL OUTLET, DO NOT PLACE YOUR EYES CLOSE TO THE OPENING OF THE DISC TRAY AND OTHER OPENINGS TO LOOK INTO THE INSIDE OF THIS UNIT.

USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.

DO NOT OPEN COVERS AND DO NOT ATTEMPT TO REPAIR YOURSELF. REFER SERVICING TO QUALIFIED PERSONNEL.

CAUTION:

LASER RADIATION WHEN OPEN DO NOT STARE INTO BEAM.

(Inside of product)

FCC NOTE:

This equipment has been tested and found to comply with part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when operated in a residential environment. If this equipment does cause interference to radio or television reception, which can be determined by turning the equipment off and on, use the equipment in another location and/or utilize an electrical outlet different from that used by the receiver. If necessary, consult the dealer or an experienced radio/TV technician for help. The user may find the booklet, “Something About Interference” available from FCC local regional offices helpful.

FCC Caution:

To assure continued compliance, (example- use only shielded interface cables when connecting to other devices.) Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.

Region Management Information:

This DECK is designed and manufactured to respond to the Region Management Information that is recorded on a DVD disc. If the Region number described on the DVD disc does not correspond to the Region number of this DECK, this DECK cannot play this disc.

● The Region number for this DECK is “1”.

● The Player will play DVD-Video marked with labels

containing “1” or “ALL”.

Example:

ALL

D4734S-K P1-25 (040202).p65 2004/02/02, 15:133

Before Using

Congratulations

on your purchase of one of the most sophisticated and reliable products on the market today. Used properly, it will bring you years of enjoyment. Please fill in the information below. The serial number is on the tag located on the back of your DECK.

• Date of Purchase

• Dealer Purchased From

• Dealer Address

• Dealer Phone No.

• Model No.

• Serial No.

Accessories

Remote Control

EUR7724KC0

Loading the Batteries

Battery replacement caution

• Do not mix old and new batteries.

• Do not mix alkaline with manganese batteries.

Record/ Playback Time

Only use tapes with the mark in this DECK.

Tape Speed

Setting

(Standard Play)

SLP

(Super Long Play)

PV-D4734S-K

Batteries 2 “AA”

RF Coaxial Cable LSJA0418

1) Open cover.

2) Insert batteries as marked.

3) Close cover.

Type of Video Cassette

2 Hours

6 Hours 8 Hours

2 Hours

40 Minutes

T180T160T120

3 Hours

9 Hours

Head Cleaning

Playing older or damaged tapes may eventually cause video heads to become clogged.

Video Head Clog Sensor

V I D

During playback, this screen appears if clogging is detected. To remove screen, press PLAY on the remote or DECK.

• Use “dry” type head cleaning cassette only.

(Part No. NV-TCL30PT is recommended.)

• Follow cleaning tape instructions carefully. Excessive use of tape can shorten head life.

• If head clog symptoms persist, contact your nearest Factory Servicentre or authorized Servicentre (see p. 61).

EO HEADS MAY

EED

CLEAN I NG PLEASE I NSERT HEAD CLEAN I NG CASSETTE OR REFER

MANUAL

END

: PL

Cleaning DECK

Use a soft cloth or dusting attachment of a vacuum cleaner to remove dust from the ventilation holes on the back sides and bottom of the cabinet. Plastic surfaces are easily scratched and can be marred by alcohol and various solvents. Avoid excessive use of oil-based furniture polishes since the materials used in the cabinet will accumulate more dust. We recommend using a non-abrasive, antistatic cleaner and polisher.

Features for a Quality Picture (VCR)

Digital Auto Picture

Automatically controls the video output signal for less noise depending on the tape condition.

Digital Auto Tracking

Continuously analyzes the signal and adjusts for optimum picture quality.

Manual Tracking Control (to reduce picture noise)

Use during Playback and Slow Motion mode to reduce picture noise. Press CH (TRACKING) / on the remote control or on DECK until the picture clears up. To return to Auto Tracking, press POWER off, then on again a few seconds later.

V-Lock Control (to reduce picture jitter)

In Still mode, CH (TRACKING) / operate as a V-Lock control.

D4734S-K P1-25 (040202).p65 2004/02/02, 15:134

Table of Contents

DVD / VCR

Important Safeguards and Precautions ............................ 2, 3

Before Using ............................................................................4

DECK & Cassette Information ........................................... 6 , 7

Location of Controls ....................................................... 8 ~ 10

Displays (On Screen Displays and Multi Function Display) .................... 11

Connections .................................................................. 12 ~ 15

Initial Setup for Basic Connections (Ready to Play) .......... 16, 17

VCR Reset Language, Channels, Clock, VCR’s Output Channel ... 18, 19

Playback/ Record on a Tape........................................... 20, 21

DVD

Basic DVD Operation ...................................................... 22, 23

Timer Recording .............................................................. 24, 25

MTS Broadcast/ VHS Hi-Fi Stereo System .................... 26, 27

Multi-Brand Control Feature ........................................... 28, 29

Tape Operation (Search System) ......................................... 30, 31

Special VCR Features ................................................... 32 ~ 34

Copying Your Tapes (Dubbing) ......................................................... 35

(Connection)

Initial Setup

Operation

Basic

Operation

VCR

Disc Operation ............................................................... 36 ~ 41

DVD-RAM Operation (DVD-RAM only)................................. 42, 43

DVD Operation using On-Screen Displays .................44 ~ 48

MP3/WMA/JPEG Playback Operation .......................... 49 ~ 51

Settings for DVD Operation .......................................... 52 ~ 55

Language Code List .............................................................. 56

DVD / VCR

Warning and Instruction Displays........................................ 57

Before Requesting Service............................................. 58, 59

Limited Warranty ................................................................... 60

Servicentre List...................................................................... 61

Index ................................................................................. 62, 63

D4734S-K P1-25 (040202).p65 2004/02/02, 15:135

Operation

DVD

Information

For Your

DECK & Cassette Information

Prevent Accidental Tape Erasure

Break off the tab to prevent recording.

Record Tab

Screw driver

To record again

Cover the hole with cellophane tape.

Built-in Head Cleaner

A clean video head helps produce a clear picture. So, we have equipped your DECK with a built-in, nonchemical head cleaning system that helps prevent clogging of the video heads. Cleaning is performed each time you load or unload a video cassette.

• This feature is preventative only, If your video heads are seriously clogged, consider the use of a chemical non-abrasive head cleaning kit or take your DECK to a Servicentre (see p. 61).

Disc formats supported by this DECK

DECK can play back discs bearing any of the following marks:

Logo Disc type

DVD-RAM (Version 1.1 of the Video Recording Format a unified video recording standard)

DVD (DVD-Video)

DVD-R (DVD-Video formatted discs [finalized])

CD (CD-DA)

CD-R/CD-RW

• CD-DA format

• WMA/MP3/JPEG file

and finalized.*

[Discs Played 8cm (3") or 12cm (5")] *A process that allows play on compatible equipment.

Discs which cannot be played

• DVD with Region No. other than “1” or “ALL”

• PAL discs, DVD-ROM, DVD-Audio, DVD-RW,

DVD+R, DVD+RW, CD-ROM, CDV, CD-G, CVD, SVCD, SACD, CD-TEXT, Divx Video Disc, Photo-CD and Video CD

Notes

• Do not use irregularly shaped discs (e.g. heart-

shaped), as these can damage the unit.

• It may not be possible to play CD-R, CD-RW,

DVD-R and DVD-RAM in all cases due to the type of disc or condition of the recording.

DVD-RAM discs

DVD-RAM discs must meet the following conditions for this unit to be able to play them.

Type

Capacity

• Remove TYPE 2 and 4 discs from their cartridges

before use, then return them when you are finished. Read the instructions for the disc carefully.

• Some parts of the disc, for example where one program

ends and another begins, may not play smoothly.

• Non-cartridge discs

• Discs that can be removed from

their cartridges (TYPE 2 and 4)

• 12 cm (5”) 9.4 GB (double-sided) and 4.7 GB (single-sided)

• 8 cm (3”) 2.8 GB (double-sided)

Disc Handling

Handling precautions

• Sticking a label on the disc may impair DVD-R playback.

• Do not attach sticker to discs. (Do not use discs with

exposed adhesive from tape or left over peeled-off stickers.)

• Only hold disc by edges as shown below. Fingerprints, dirt and scratches can cause skipping and distortion.

• Do not write on label side of disc.

• Never use record cleaning

sprays, benzine, thinner, static electricity prevention liquids, or any other solvent.

• Do not try to close disc tray when disc is not properly placed.

To clean disc surface

With a soft, damp (water only) cloth, gently wipe from the center hole to the outer edge as shown below. (Wiping in a circular pattern will scratch the surface.)

• DVD-RAM, DVD-R : Clean only with the DVD-RAM disc cleaner available. Never use cloths or cleaners for CDs etc.

If disc is brought from a cold to a warm environment, moisture may form on the disc

Wipe away moisture with a soft, dry, lint-free cloth before using disc. (See above.)

Improper disc storage

Discs could be damaged if stored or left in areas:

• exposed to direct sunlight.

• that are humid or dusty.

• near heat (i.e. heater, radiator, etc.).

Disc tray

Disc

D4734S-K P1-25 (040202).p65 2004/02/02, 15:136

Specifications

Power Source: 120 V AC, 60 Hz Power Consumption: Power On: Approx. 28 watts, Power Off: Approx. 0.85 watts

Video Signal: EIA Standard NTSC colour Video Recording System: 4 rotary heads helical scanning system

Audio Track: 1 track (Normal), 2 channel (Hi-Fi Audio Sound) Tuner Broadcast Channels: VHF 2 ~ 13, UHF 14 ~ 69 CABLE Channels: Midband A through I (14 ~ 22), Superband J through W (23 ~ 36)

Input/Output Terminal: Audio/Video Line Input/Output, RF Input/Output Input Terminal: Audio/Video Line Input (Front) Output Terminal: S-Video Output (DVD only), Component Video Output (DVD only)

Operating Temperature: 5 °C ~ 40 °C (41 °F ~ 104 °F) Operating Humidity: 10 % ~ 75 % Weight: 3.85 kg (8.5 lbs). Dimensions: 430 (W) x 95 (H) x 273 (D) mm

Discs Played (1) DVD-Video Disc 5” (12 cm) single-sided single-layer

DVD-RAM Disc 5” (12 cm) 9.4 GB (double-sided) and 4.7 GB (single-sided)

(2) Compact Disc 5” (12 cm) disc

(CD-DA) 3” (8 cm) disc (CD-R/CD-RW, MP3, WMA, JPEG)

Digital Audio Output: Digital Optical Connector Pickup: Wavelength: 655 nm (DVD), 790 nm (CD)

Note: • Designs and specifications are subject to change without notice.

Hyperband AA ~ EEE (37 ~ 64), Lowband A-5 ~ A-1 (95 ~ 99) Special CABLE channel 5A (01), Ultraband 65 ~ 94, 100 ~ 125

Audio Output 2 (L), (R)

16-15/16” (W) x 3-3/4” (H) x 10-3/4” (D) inch

5” (12 cm) single-sided double-layer 5” (12 cm) double-sided double-layer (one layer per side) 3” (8 cm) single-sided single-layer 3” (8 cm) single-sided double-layer 3” (8 cm) double-sided double-layer (one layer per side)

3” (8 cm) 2.8 GB (double-sided)

Laser power: CLASS II

(Connection)

Initial Setup

Definition of Terms (DVD)

Angle: Some DVD discs feature scenes simultaneously shot from different angles.

Chapter Number: Titles are subdivided into numbered sections. You can quickly search for

DVD: A high-density optical disc on which high-quality pictures and sound have

Subtitles: Written dialogue which appears at the bottom of the screen. Time Number: The elapsed play time from the start of a disc or title. Use to quickly find

Title Number: For DVD discs with two or more titles, the title is numbered as title 1, title 2, etc. Track Number: Numbers assigned to tracks on CDs to allow specific tracks to be quickly

Apparatus Claims of U.S. Patent Nos. 4,631,603, 4,577,216, 4,819,098 and 4,907,093, licensed for limited viewing uses only.

This product incorporates copyright protection technology that is protected by method claims of certain U.S. Patents and other intellectual property rights owned by Macrovision Corporation and other rights owners. Use of this copyright protection technology must be authorized by Macrovision Corporation, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision Corporation. Reverse engineering or disassembly is prohibited.

D4734S-K P1-25 (040202).p65 2004/02/02, 15:137

The ANGLE button can be used to view the scene from different angles. (ANGLE Indicator lights on DECK when a scene recorded at different angles is detected.)

a favorite scene using these numbers.

been digitally recorded. DVD incorporates video compression technology (MPEG II) and high-density recording technology which allow entire movies to be recorded with incredible playback quality.

scenes. (May not work with some discs.)

located.

Location of Controls

Remote Control

EJECT /

OPEN / CLOSE

pp. 20,

POWER

NUMBER keys

ADD/DELETE /

pp. 19,

ACTION

pp. 18

, 52

SET

VCR mode

p. 28

STOP

pp. 20,

REWIND /

SLOW-

pp. 20,

FAST FORWARD /

SEARCH / SLOW+

pp. 20,

PAUSE /

pp. 20,

ANGLE

. 37

SUB TITLE

. 36

TITLE

DIRECT NAVIGATOR

. 38, 42

CLEAR

STILL

Bold: VCR Function /

Italic

DVD Function

Bold Italic:VCR and DVD Functions

/ Normal: Others

TRACKING

CHANNEL

V-LOCK

pp. 4, 21,

VOLUME

MENU / PLAY LIST

DVD mode

Virtual Surround Sound (V.S.S.)

TAPE POSITION

VOLUME ADJUST

AUDIO

(SAP / Hi-Fi)

VCR/TV

TV mode

/ /

. 38, 43

SELECT

PLAY

pp. 20,

SKIP+

SKIP-

ENTER

pp.

23,

ZOOM

STATUS

p. 31,

pp. 27,

p. 21

p. 28

. 23

. 37

INPUT

p. 35

DISPLAY

p. 11,

RECORD

p. 21

SPEED

p. 21

EJECT button: When this button is pressed in VCR mode, the tape is ejected.

This button is inoperative if pressed during recording. If pressed in DVD mode, the disc tray opens or closes.

D4734S-K P1-25 (040202).p65 2004/02/02, 15:138

RETURN /

COMMERCIAL SKIP

COUNTER RESET

. 22,

ZERO SEARCH

p. 30

PROGRAM

p. 24

Front View of DECK

Bold: VCR Function

Italic

DVD Function

Bold Italic

Normal: Others

PLAY

p. 20

VCR and DVD Functions

If the disc cannot be removed...

First, unplug DECK. Then, prepare a rigid wire (e.g. an extended paper clip) and, applying moderate force, insert it straight into the hole at the base of the tray. The tray will eject a little. Now, pull the tray all the way out and remove the disc.

(Connection)

Initial Setup

STOP/EJECT

p. 20

POWER

Audio/Video Input Connector 2 (LINE 2)

REC

p. 21

CHANNEL / TRACKING/V-LOCK

pp. 4, 21

p. 35

Reset All Memory Functions

Cassette Compartment

Multi Function

Display

p. 11

Remote Sensor

Over 2 inches

Disc Tray

OPEN/CLOSE

FAST FORWARD

REWIND /

SKIP

p. 20,

SKIP

p. 20,

PLAY

STOP

Returns to factory setting. Use if relocating DECK, or if Initial Setup needs to be redone.

• Make sure a tape is not inserted in the DECK.

Turn DECK Power on.

Press and hold both VCR PLAY

and CHANNEL on the DECK for more than 5 seconds.

• The power shuts off. Perform “Initial Setup (Ready to Play)”

D4734S-K P1-25 (040202).p65 2004/02/02, 15:139

on page 16.

Location of Controls (continued)

Rear View of DECK

AC Power Plug

• While plugged into an AC outlet, this DECK consumes 0.85 W of electrical power in off mode.

Component Video Output Connector (Y, PB, PR) (DVD Only)

Optical Digital Audio Output Connector (DVD Only)

S-Video Out Connector (DVD Only)

pp.

10, 13

Bold: VCR Function

Bold Italic:VCR and DVD Functions

VHF/UHF Antenna Output Terminal p.12

VHF/UHF Antenna Input Terminal p. 12

Video Output Connector

•

Video Input Connector p. 35

Audio Output 1 Connector (L/R)

Audio Output 2 Connector (L/R)

Italic:DVD Function

•

Audio Input Connector (L/R) p.

The following table shows the status of the output jacks when in VCR or DVD mode.

VCR

DVD

Video Output Audio Out 1 Audio Out 2

YES YES

Component Video Output

N/A

S-VIDEO OUT

N/A

YES

• PROG functions on the remote are not available when using Component Video Output and

Note

S-VIDEO OUT. Please set TV to either RF INPUT or VIDEO INPUT, and then press PROG.

To enjoy PROGRESSIVE SCAN video

(1). Connect

(See p. 13.)

(2). When PROGRESSIVE OUT is set to “ON” in the DVD Main Menu (p. 55), a Progressive

Scan signal is output from the

Notes

• The screen may shift off-center when using progressive output. Please adjust the screen position if this occurs. (Refer to your TV manual.)

• If the television is not progressive compatible, a progressive scan picture is not available. Connect the Video Output or S-Video Output connector (see p. 12, 13) and set PROGRESSIVE OUT to “OFF” in the DVD Main Menu. (See p. 55.)

Component Video Output

Component Video Output Connector

to the component video input terminals of a television.

D4734S-K P1-25 (040202).p65 2004/02/02, 15:1310

Displays (On Screen & Multi Function)

On Screen Displays (VCR)

Function & Channel Displays

CH 0 8

When a function button is pressed, e.g. PLAY, or you change channels, a 5-second display appears.

VCR Status & Clock Displays To display or remove screen shown at right,

➛➛

➛ press DISPLAY.

➛➛

Rec Time Remaining (OTR mode only, see p. 21.)

Multi Function Display

VCR mode Indicator

Lights up when DECK is in VCR mode.

Function Status

Broadcast Audio Being Received (See pp. 26, 27.)

Blank Tape/ No Video Signal Indications

Whenever a blank section of a tape comes up in Play mode, or when the selected channel has no broadcast signal with Weak Signal Display Feature (p. 33) set to OFF, the TV screen will turn solid blue.

Current Time

Channel

REW

1 2 : 0 0A 0 : 25 STER SAP M

ONO

CH 02

-0 : 1 2 : 3 4 SP

Counter

Tape Speed (See p. 4.)

DVD mode Indicator

Lights up when DECK is in DVD mode.

(Connection)

Initial Setup

Tape Indicator

Lights up when a tape is inserted.

Hi-Fi Indicator

Lights up when Hi-Fi audio is present in Play mode.

VCR

Hi - Fi

ANGLE

ANGLE Indicator

Lights up when a scene recorded at different angles is detected. (See p. 37.) (DVD only)

Clock/ Status/ Channel/ Speed Display

Displays current time. Briefly displays DECK status when you press a function button, channel number or “L1” or “L2” when you select channel or line input, and recording speed when you press SPEED.

D4734S-K P1-25 (040202).p65 2004/02/02, 15:1311

DVD

REC

A M

TIMER

AM/PM Indicator

DISC Indicator

Lights up when a disc is inserted.

VCR REC Indicator

Lights up during recording.

Timer Indicator

Lights up when DECK is set for Timer Recording, or when One Touch Recording (OTR) is used. Flashes when Timer Recording is set, but a tape has not been inserted into DECK and when a power interruption occurs during Timer Programming.

Connections

Basic Connections

• If your TV has AUDIO and VIDEO IN terminals, connect them to DECK for higher

quality picture and sound.

• You can enjoy stereo sound even if your TV is not stereo by connecting a stereo

amplifier to DECK.

• Connect DECK and TV with an RF Coaxial Cable a (supplied) or an AV Cable (not supplied) as shown in the figure below.

■ ■

■ DSS Receiver DECK TV

■ ■

■ DECK TV

■ ■

Antenna or Cable

■ Cable Box DECK TV

■ ■

DSS Receiver

OUT

DVD/VCR DECK

IN FROM ANT.

IN 1

OUT

VIDEO

AUDIO

When using “Nut type” RF coaxial cables, tighten with fingers only. Overtightening may damage terminals.

VHF/UHF

OUT TO TV

OUT

Cable Box

1 Disconnect antenna or cable from TV

and connect to DECK.

2 Connect DECK to TV with RF Coaxial Cable.

RF COAXIAL CABLE

AUDIO IN

(supplied)

VIDEO

AV CABLE

VHF/ UHF

(not supplied)

Note to CABLE system installer

This reminder is provided to call the CABLE system installer’s attention to Article 820-40 of the NEC in USA (and to the Canadian Electrical Code in Canada) that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical.

D4734S-K P1-25 (040202).p65 2004/02/02, 15:1312

Other Connections

■ ■

■ With a Cable Box (DECK

■ ■

DVD/VCR DECK

IN FROM ANT.

IN 1

OUT

VHF/UHF

OUT TO TV

■■

■

Connect With Two Cable Boxes

■■

ANT or CATV

Cable Box

Cable Box TV)

OUTIN

DVD/VCR DECK

ANT

CATV

Cable Box

OUT

2-Way Splitter

OUT 1

OUT 2

OUT

Cable Box

OUTIN

IN 1

IN FROM ANT.

VHF/UHF

OUT TO TV

A/B Switch

VHF/ UHF

IN 2IN 1

• view any (including

• use Remote

• record and view

AUDIO

VIDEO

scrambled) channel.

Control to select channels without using Multi-brand control feature.

both scrambled and unscrambled channels if additional equipment is added. This connection requires: two converter boxes, an A/B switch, and a 2-way splitter.

OUT

AUDIO

VIDEO

OUT

R L

VHF/ UHF

You CannotYou Can

• record scrambled channels.

You CannotYou Can

• view a channel other than the one selected for any type of recording.

• set a Timer recording of a channel unless you select it on the Cable Box.

Connections For DVD Only (enjoying higher picture quality)

Connect AUDIO OUT2 (L, R) to the AUDIO IN (L, R) of the TV. (audio input for COMPONENT

or S-VIDEO mode). If your TV has COMPONENT VIDEO INPUT, connect to COMPONENT VIDEO OUT.

If your TV does not have COMPONENT VIDEO INPUT but has S-VIDEO INPUT, connect to S-VIDEO OUT.

When in DVD mode, set your TV to either COMPONENT VIDEO IN or S-VIDEO IN.

Notes

• You can watch DVDs through the S-VIDEO or COMPONENT VIDEO, VHF/UHF OUT TO TV,

and VIDEO OUT connections to your TV. The VCR and TUNER pictures are available only from the VIDEO OUT and VHF/UHF OUT TO TV connections to your TV.

• PROG functions on the remote are not available when using S-VIDEO OUT and COMPONENT Video Output. Please set TV to either RF INPUT or VIDEO INPUT, and then press PROG.

• TV must have capability to accept and display a progressive scan signal to use PROGRESSIVE mode. Consult your TV operating instructions.

DVD/VCR DECK

DVD OUTPUT

S-VIDEO OUT

COMPONENT

VIDEO OUT

P R

AUDIO OUT2

AUDIO

VIDEO

S-VIDEO IN

From DECK’s

A/V OUTPUT

(Connection)

Initial Setup

D4734S-K P1-25 (040202).p65 2004/02/02, 15:1313

Connections (continued)

Audio Connections

Ready Checklist

Turn down the volume, then turn DECK, as well as other equipment to be connected, off before proceeding with connection. Do not block ventilation holes of any of the equipment and arrange them so that air can circulate freely. Read through the instructions before connecting other equipment. Ensure that you observe the colour coding when connecting audio and video cables.

■ Connecting Amplifier (2ch stereo system)

DVD/VCR DECK

AUDIO OUT2

Speaker

Amplifier

AUDIO IN

R L

Enjoying digital audio output from the digital audio output connector

Notes on audio output from the optical digital audio output connector

Disc

DVD-Video

DVD-RAM

Sound recording format

Dolby Digital

Linear PCM (48/96 kHz 16/20/24 bit)

DTS Dolby Digital

Optical digital audio output from connector

Dolby Digital bitstream (1 - 5.1 ch) or PCM (48 kHz sampling/16 bit only)*

Linear PCM (2 ch) (48 kHz sampling/16 bit only)*

Bitstream or PCM (48 kHz sampling/16 bit only)* Dolby Digital bitstream (1 - 5.1 ch)

or PCM (48 kHz sampling/16 bit only)

Linear PCM(48 kHz/16 bit)

CD MP3 WMA

*1 The type of audio output from the connector can be selected by the Settings for DVD

Operation. (See p. 53.)

*2 When “LPCM(DVD)” is set to OFF in the DVD Main Menu, only 48 kHz sampling/16 bit is ouput.

When set to ON, sampling of sound quality greater than 48 kHz/16 bit is reduced to 48 kHz/16 bit. (See page 53.)

Linear PCM MP3 WMA

Linear PCM (2 ch) Linear PCM (44.1 kHz sampling)

Linear PCM (It depends on the MP3 file) Linear PCM (It depends on the WMA file)

For your reference:

• Dolby Digital is a digital sound compression technique developed by the Dolby Laboratories Licensing Corporation. Supporting 5.1-channel surround sound, as well as stereo (2-channel) sound, this technique enables a large quantity of sound data to be efficiently recorded on a disc.

• Linear PCM is a signal recording format used in CDs. While CDs are recorded in 44.1 kHz/16 bit, DVDs are recorded in 48 kHz/16 bit up to 96 kHz/24 bit.

• If you have a Dolby Pro Logic Surround decoder, you will obtain the full benefit of Pro Logic from the same DVD movies that provide full 5.1 channel Dolby Digital soundtracks, as well as from titles with the Dolby Surround mark. For information on Panasonic Dolby Pro Logic Surround Sound Decoders please contact your local dealer.

Manufactured under license from Digital Theater Systems, Inc. US Pat. No’s. 5,451,942, 5,956,674, 5,974,380, 5,978,762, 6,487,535 and other US. and world-wide patents issued and pending. “DTS” and “DTS 2.0 + Digital Out” are trademarks of Digital Theater Systems, Inc. Copyright 1996, 2003 Digital Theater Systems, Inc. All Rights Reserved.

Manufactured under license from Dolby Laboratories. “Dolby,” “Pro Logic,” and the double-D symbol are trademarks of Dolby Laboratories.

Speaker

D4734S-K P1-25 (040202).p65 2004/02/02, 15:1314

■ Connecting Amplifier (5.1 ch Surround system) [Digital connection]

DECK Dolby Digital Receiver Amplifier Speaker

DECK DTS (Digital Theater Systems) Receiver Amplifier Speaker

When DVDs recorded in Dolby Digital or DTS are played, Dolby Digital bitstream or DTS bitstream is output from the DECK OPTICAL digital audio output connector. When DECK is connected to a Dolby Digital or DTS receiver, you can enjoy theater-quality audio in your home. [An optical digital audio cable (optional) is required when an optional Dolby Digital or DTS receiver is used.]

(Connection)

Initial Setup

Notes on connecting an optical digital audio cable (optional)

• Firmly connect the cable to the connector.

DVD/VCR DECK (Rear)

Optical Digital Audio Cable

Surround Speaker

[5.1 ch Surround system]

Front Speaker

To Optical Digital Audio Input Connector

Center Speaker

Amplifier

Decoder with Dolby Digital / DTS processing

Receiver

Surround Speaker

Front Speaker

Subwoofer

(optional)

Caution for optical digital audio output connector:

• When connecting an amplifier (with an Optical Digital Input Connector) which does not contain the Dolby Digital or DTS receiver, be sure to select “PCM” at “Dolby Digital” and “PCM” at “dts” of the Settings for DVD Operation “Audio Output”

(see p. 53). Otherwise, any attempt to play DVDs may cause such a high level of noise that it may be harmful to your ears and damage your speakers.

• When a Dolby Digital/DTS receiver is connected, please select “Bitstream” at “dts” or “Dolby Digital” of the Settings for DVD Operation “Audio Output”. If “PCM” is selected, there will be stereo sound. (See p. 53.)

• CDs can be played as usual.

Note:

• Some DTS receivers which do not support DVD-DTS interface may not work properly with DECK.

D4734S-K P1-25 (040202).p65 2004/02/02, 15:1315

Initial Setup for Basic Connections (Ready to Play)

Before doing Initial Setup

Turn TV on.

See connections a RF Coaxial Cable Connection and b AV Cable Connection on page 12.

<RF Coaxial Cable Connection> Set TV to channel 3.

Set TV to VIDEO.

[DECK

• Go to “Initial Setup (Ready to Play).” (See below.)

[Cable Box

• Turn on Cable Box and set it to your Public Broadcasting Station (PBS) channel

• If you use a DSS Receiver, it must be turned off.

Initial Setup (Ready to Play)

Press VCR on remote for VCR mode.

Plug DECK Power Cord into AC wall outlet. DECK comes on and SELECT LANGUAGE screen appears. When one of “1”, “2”, “3” keys is pressed, auto

channel and clock set starts.

• If screen below does not appear, check DECK - TV connection and, if TV is tuned to

• To change VCR’s output channel, please refer to “VCR’s Output Channel” on page 19.

• If wrong language is set, do “Reset All Memory Functions” (p. 9).

➛➛

➛ TV]

➛➛

➛ DECK

➛➛

in your time zone.

channel 3, try switching it to channel 4.

➛➛

➛ TV], [DSS

➛➛

➛ DECK

➛➛

➛ TV]

➛➛

Plug VCR Power plug into an AC wall outlet.

SELECT LANGUAGE

SH :PRESS 1

ENGL

S :APPUYER 2

FRANÇA ESPAÑOL :OPR

CH AUTO SET PROCEEDING

CANCEL : STOP

AUTO CLOCK SET

PROCEEDING

CANCEL : STOP

D4734S-K P1-25 (040202).p65 2004/02/02, 15:1316

I M I

Select language Press 1 : English Press 2 : French Press 3 : Spanish

Notes

• Function buttons are void during Initial Setup.

• To eject a tape during Auto Set, press EJECT on remote

or STOP/EJECT twice on DECK. Then make settings manually. (See p. 18.)

• If Auto Clock Set takes more than 30 minutes, press STOP and perform settings manually. (See p. 18.)

Continued on next page...

*Important: If a remote control button does not work when pressed,

press the VCR button on the remote and try the button again.

EJECT

ACTION

SELECT

SET

VCR

Settings are made automatically. When complete, this screen appears.

If “AUTO CLOCK SET IS INCOMPLETE” appears, manually set clock (below).

AUTO CLOCK SET

I NCOM

PLETE

PLEASE SET CLOCK BY PRESSING

ACT I ON KEY

Manual Clock Set

If Auto Clock Set was incomplete.

Press ACTION* on remote to display CLOCK screen.

SET CLOCK

1 / 1/2004

- - - - - - - - -- - - - - - - -- - - - - -

THU

-- -12:00 DST : O

(Connection)

Initial Setup

STOP/EJECT

D4734S-K P1-25 (040202).p65 2004/02/02, 15:1317

SELECT : END:

Press set. In the same manner, select and set

to select the month and SET to

SET : SET

ACT I ON

the date, year, time, and DST (Daylight Saving Time).

SET CLOCK

6 /20/2004

- - - - - - - - -- - - - - - - -- - - - - -

SELECT : START

Press ACTION to start clock and exit.

SUN

- -15:30

SET : SET

: ACT I ON

DST : O

Reset Language, Channels, Clock, VCR’s O

SELECT : EXIT

: ACTION

SET : SET

MENU SET UP VCR

SET UP CLOCK

SET UP CHANNEL IDIOMA/LANGUE : ENGLISH VCR’S OUTPUT CH:3

AUTO CLOCK SET

MANUNU

T I M

E ZONE AD

JUS

T :

SET CLOCK

SELECT :

SET : SET

EXIT:

ACT I ON

DST : O

1 / 1/2004

THU

-- -12:00

- - - - - - - - -- - - - - - - -- - - - - -

SET CLOCK

SELECT :

SET : SET

END:

ACT I ON

SET UP VCR

SET UP CLOCK SET UP CHANNEL IDIOMA/LANGUE : ENGLISH VCR’S OUTPUT CH:3

SELECT :

: ACTION

SET : SET

EXIT

Press ACTION*

to display MENU.

Language

1) Press to select language item.

MENU SET UP VCR SET UP CLOCK SET UP CHANNEL

IDIOMA/LANGUE : ENGLISH

VCR’S OUTPUT CH:3

SELECT : EXIT

2) Press SET repeatedly to change language item as shown below.

MENU PREPARAR VCR FIJAR RELOJ FIJAR CANAL

LANGUE/LANGUAGE:ESPAÑOL

SALIDA DE VCR CANAL : 3

ELEGIR : SALIR

For Spanish

SET : SET

: ACTION

FIJAR : SET

: ACTION

For French

➡

• PROGRAM functions are not available when using COMPONENT Video Output and S-VIDEO OUT. Please set TV to either RF INPUT or VIDEO INPUT, and then press PROGRAM.

Channels

1) Press to select

“SET UP CHANNEL,” and press SET.

MENU SET UP VCR SET UP CLOCK

SET UP CHANNEL

IDIOMA/LANGUE : ENGLISH VCR’S OUTPUT CH:3

SELECT :

: ACTION

CABLE

: ACT I ON

SET : SET

NNE

SPLAY : OFF

SET : SET

EXIT

2) Press to select “ANTENNA,” then press SET to set your antenna system (“TV” or “CABLE.”)

SET UP CHA

ANT

ENNA

AUTO SET WEAK

S I GNAL D I

SELECT : EXIT

3) Press to select “AUTO SET,” then press SET.

• If you use a Cable Box,

set it to the PBS channel in your time zone.

Clock

1) Press to select

“SET CLOCK,” and

press SET.

2) Press to select “MANUAL,” and press SET. (For Auto Clock Set, select “AUTO CLOCK SET.”)

(“TIME ZONE ADJUST”

appears only when auto clock is set.)

MENU SET UP VCR SET UP CLOCK SET UP CHANNEL

IDIOMA/LANGUE : ENGLISH

VCR’S OUTPUT CH:3

SELECT : EXIT

For English

3) Press ACTION to exit.

D4734S-K P1-25 (040202).p65 2004/02/02, 15:1318

: ACTION

SET : SET

CH AUTO SET PROCEEDING

CANCEL : STOP

• After Channel Auto Set is finished, Auto Clock Set will be performed.

3) Press and to select, then set the date, time, and DST (Daylight Saving Time).

4) Press ACTION to start Clock and exit this mode.

HANNEL

08 ADDED

HANNEL

08 DELE T

*Important: If a remote control button does not work

when pressed, press the VCR button on the remote and try the button again.

Time Zone Adjust

(Only when Auto Clock is set.)

1) Press to select “SET CLOCK,” and press SET.

MENU SET UP VCR

SET UP CLOCK

SET UP CHANNEL IDIOMA/LANGUE : ENGLISH VCR’S OUTPUT CH:3

SELECT :

: ACTION

SET : SET

EXIT

VCR’s Output Channel

1) Press to select

“VCR’S OUTPUT CH.,” and press SET.

MENU SET UP VCR SET UP CLOCK SET UP CHANNEL IDIOMA/LANGUE : ENGLISH

VCR’S OUTPUT CH:3

SELECT :

: ACTION

SET : SET

EXIT

POWER

NUMBER keys

CH /

ADD/DLT ACTION SELECT

SET VCR

Operation

Basic

2) Press to select

“TIME ZONE ADJUST,”

SET CLOCK

AUTO CLOCK SET MANU

T I M

E ZONE AD

JUS

T :

SELECT :

SET : SET

EXIT

: ACT I ON

and press SET to subtract or add hour(s) as necessary.

3) Press ACTION.

•“TIME ZONE ADJUST”

returns to “0” if clock is set manually.

2) Press SET.

I F YOU PRESS KEY, VCR’ SW I

TCHES TO

ACT I O

S OUTPUT CH

CH 4.

3) Press ACTION.

PLEASE TUNE YOUR TV TO CH 4.

➡

After 3 seconds

MENU SET UP VCR SET UP CLOCK SET UP CHANNEL IDIOMA/LANGUE : ENGLISH

VCR’S OUTPUT CH:4

SELECT :

: ACTION

SET : SET

EXIT

• To Make Corrections, repeat steps 1) ~ 3).

Add or Delete a Channel

To add channel: Select channel with NUMBER keys

and press ADD/DLT.

To delete channel: Select channel with CH / or

NUMBER keys and press ADD/DLT.

DST (Daylight Saving Time)

DECK auto adjusts clock for DST. (p. 17.)

Spring (First Sunday in April)

DST:ON

Autumn (Last Sunday in October)

DST:ON

• If your area does not observe

• Keep these time changes in mind

➛➛

➛ Sets clock ahead one hour.

➛➛

➛ Turns clock back one hour.

➛➛

Daylight Saving Time, select DST:OFF.

when programming DECK for timer recordings.

D4734S-K P1-25 (040202).p65 2004/02/02, 15:1319

Playback/ Record on a Tape

Ready Checklist

All connections are made. (pp. 12 ~ 15) TV and DECK are plugged in. TV is on and tuned to CH 3, 4, or VIDEO. Remote is in VCR mode. (Press VCR.)

Playback a Tape

Insert a tape.

• DECK power comes on. If Auto VCR/TV (see p. 32) is set to “OFF,” press VCR/TV on the remote for VCR mode.

Press PLAY* to play a tape.

• If tape has no rec. tab (p. 6), auto play begins.

Special Features During Play

Forward/Reverse Scene Search

➛➛

➛ Press FF/SLOW+ or REW/SLOW-.

➛➛ ➛➛

➛ Press PLAY to release.

➛➛

After search has begun, each additional press of

FF or REW changes speed

Notes

• Picture interruption may occur with some TVs.

• FF and REW search speed may vary depending

on current tape position.

• After 10 minutes in search mode, VCR returns to Play mode to protect the tape and the video heads.

Still (Freeze) Picture

➛➛

➛ Press PAUSE/STILL.

➛➛ ➛➛

➛ Press PLAY to release.

➛➛

Frame by Frame Picture

➛➛

➛ Press PAUSE/STILL in Still mode.

➛➛ ➛➛

➛ Press PLAY to release.

➛➛

Slow Motion Picture

➛➛

➛ Press FF/SLOW+ (increase speed) or

➛➛

REW/SLOW- (decrease speed) in Still mode.

➛➛

➛ Press PLAY to release.

➛➛

EJECT

VCR

FF/ SLOW+

REW/ SLOW-

PAUSE/ STILL

REC

Notes

• These features work best in SP or SLP mode.

• The sound will be muted.

• To reduce picture noise, see “Manual Tracking Control” on page 4.

• After 3 minutes in Still or Slow mode, VCR

stops to protect the tape and the video heads.

VCR/TV

CH /

DVD

PLAY

STOP

SPEED

Playback using DECK buttons

Insert a tape.

Press PLAY.

Press STOP to stop a tape.

Rapid Rewind/FF

Press REW/SLOW- or FF/SLOW+ in Stop mode to rewind or fast forward a tape.

• Rewinds a T-120 tape in approx. 1 minute.

Press EJECT on remote, or STOP/EJECT on DECK to eject a tape.

D4734S-K P1-25 (040202).p65 2004/02/02, 15:1320

Multi Function Display

Press STOP/EJECT to stop and/ or eject a tape.

*Important: If a remote control button does not work when pressed,

REC T I ME : 0 :

ME : PRESS REC KEY

CANCEL : PRESS STOP KEY

CH 02

: 0 0 : 0

press the VCR button on the remote and try the button again.

Record on a Tape

Insert a tape with a record tab (p. 6).

• DECK power comes on. If Auto VCR/TV (see p. 32) is set to “OFF,” press VCR/TV on the remote for VCR mode.

Press CH , or NUMBER keys

to select the channel.

• If channel number is over 100, first press 100 key then the other 2 digits.

• For “LINE” input, see p. 35.

Press SPEED

to select the record speed (p. 4).

SP = Standard Play SLP = Super Long Play

• Speed appears on-screen and on Multi Function Display.

Press REC

to start recording.

(The VCR REC indicator lights up on Multi Function Display),

• To edit out unwanted scenes, press PAUSE/STILL to pause, and again to resume recording.

• You cannot view another channel during recording.

Press STOP

to stop recording.

One Touch Recording (recording in progress),

➛➛

➛ press REC repeatedly to set the recording length

➛➛

(30 min. ~ 4 hours) (see right).

• DECK shuts off after the preset record length.

Record one station, watch another,

➛➛

➛ press VCR/TV on the remote

➛➛

(change to TV mode),

➛➛

➛ select channels at TV (recording continues).

➛➛

Select Channels at DECK (In Stop or Rec. Pause mode)

➛➛

➛ press VCR/TV on the remote

➛➛

(change to TV mode),

➛➛

➛ select channels at DECK.

➛➛

Play a disc while recording a tape.

➛➛

➛ insert a disc during recording,

➛➛ ➛➛

➛ press

➛➛

DVD

, and then press

PLAY

This video recorder, equipped with HQ (High Quality) system, is compatible with existing VHS equipment. Only use tapes with the mark. Only tapes tested and inspected for use in 2, 4, 6, and 8 hour machines are recommended.

Note

Remove loose or peeling labels from tapes to prevent tape jam.

Normal Rec

0:30 1:00

1:302:003:004:00

Record using DECK buttons

Press REC to start recording.

Insert a tape.

Operation

Basic

Notes

• It is not possible to record from DVD/ CD to

VHS tape using DECK.

• Watching one channel and recording another is not possible when using Cable Box or DSS Receiver.

• After 5 minutes in Pause mode, DECK stops to protect a tape and video heads.

D4734S-K P1-25 (040202).p65 2004/02/02, 15:1321

Select

Channel.

Multi Function Display

Press STOP/EJECT to stop.

Basic DVD Operation

Ready Checklist

All connections are made. (pp. 12 ~ 15) DECK is plugged in. If DECK is connected to an audio amplifier,

turn the stereo system’s power on.

OPEN/ CLOSE

POWER

NUMBER keys

SELECT

SET FF/

SLOW+ REW/

SLOWPAUSE/

STILL TITLE

STOP DVD

PLAY

SKIP+ SKIP

VSS

RETURN

If an interactive DVD*1 is used and TITLE MENU appears, go to step 5.

Operation using DECK buttons

Press

POWER.

Insert a disc.

3, 7

OPEN/CLOSE.

Press PLAY.

Press STOP.6

Using NUMBER keys starts play automatically.

The number of available titles varies with each disc.

<Input

Example>

Press previous menu screen.

• SKIP function not available with all discs.

To return to menu (play stops)

Press

*1Interactive DVD...

May include multiple camera angles, stories, etc.

Press

POWER*

Press

DVD

• If a disc is already inserted, go to step 4. (Depending on the disc, playback may start automatically.)

Press

OPEN/CLOSE

and then place a disc into the disc tray.

Press

PLAY

Disc tray closes automatically.

READING

SKIP+

| or

Please refer to disc jacket for operation information.

TITLE, MENU,

Press

STOP

Press

OPEN/CLOSE

on the remote or DECK.

to select DVD mode.

• Hold disc by its edges only (p. 6) with printed side up and use guides to place into tray.

Use 3” (8 cm)

to start playing.

• You may also close tray by

pressing

• Data reading time differs with each disc.

1 digit number 1 •••• 1 2 digit number 12 ••• 10 ➛ 1 ➛ 2

SKIP-

RETURN

to stop playing.

or 5” (12 cm) disc.

DVD-RAM ➡ see p. 42

OPEN/CLOSE

T I TLE MENU

Cas t l es

Dogs

i r

SET

(see

PLAY

Love

Press or

NUMBER keys

below) to select title, and press

PLAY

to start playing.

• Pressing is not necessary when using

NUMBER keys.

| to go to next or

to eject the disc.

D4734S-K P1-25 (040202).p65 2004/02/02, 15:1322

*Important: If a remote control button does not work when pressed,

VSS OFF (default)

VSS1

VSS3

VSS2

press the DVD button on the remote and try the button again.

■ Forward/Reverse Scene Search

Press

FF/SLOW+

PLAY

Press

• Search speed, slow at first, increases with each additional press of the button up to 5 levels.

REW/SLOW-

to release.

during play.

■ Forward/Reverse Chapter/Track Skip

Press

SKIP+

| or

SKIP- |

during play. Each press skips a chapter (DVD), track (CD) or Program/Play List/Marker (DVD-RAM).

DVD and CD

• Pressing

chapter/track returns to the start of that chapter/track. Each additional press skips back one chapter/track.

DVD-RAM

• Pressing

program/play list returns to the start of that program/play list. Each additional press skips back one program/play list.

Current playback position Marker

Program/Play List Program/Play List Program/Play List

SKIP- |

Current playback position

Chapter/Track Chapter/Track Chapter/Track

Reverse Skip Forward Skip

SKIP- |

Reverse Skip Forward Skip

once midway through a

■ Still Picture or Pause

Press

PAUSE/STILL

Press

PLAY

• DVD : DECK will enter still picture mode.

• CD : DECK will enter pause mode.

to release.

during play.

■ Frame by Frame Picture (DVD)

Press

PAUSE/STILL PLAY

Press

• Each press advances picture one frame.

• Hold button down for consecutive frame advance.

• Whether pictures are advanced by “FRAME” or

“FIELD” is selected automatically. (See p. 54.)

to release.

in still mode.

■ Slow Motion Picture (DVD)

Press

FF/SLOW+

Press

PLAY

• Slow motion speed, slow at first, is increased

with each additional press of the button up to 5 levels.

REW/SLOW-

to release.

in still mode.

Auto-Power Off Function

Power turns off after DECK has been in Stop mode (DVD) for about 5 minutes.

• When appears on the screen while a button is being operated, it means that the corresponding operation is prohibited by DECK or the disc.

V.S.S. (Virtual Surround Sound)

Enjoy a surround-like effect if you are using two front speakers only. The effect is broadened and sound seems to come from virtual speakers on either side if the disc has surround signals recorded on it.

Press

VSS

• The Surround sound effect can be changed by pressing VSS repeatedly as shown by the figure below.

in DVD mode.

VSS OFF

Note

• Surround sound effect is available in DVD mode only.

• Turn off the surround effects on the other equipment.

• V.S.S. will not work, or will have less effect, with some discs.

• Turn V.S.S. off if it causes distortion.

• Sound will only come from the two front

speakers if V.S.S. is on.

Resume Function

DECK memorizes the point where STOP is pressed (STOP is displayed on screen).

Press

PLAY

Pressing

cancels RESUME, however, RESUME is not cancelled when power is turned off and on.

• RESUME works only with discs for which elapsed play time is displayed during play.

• When a DVD-RAM still picture is played back, the counter will not be displayed, however RESUME will function.

Notes

• Please read the disc jacket for operation information.

• If a single sided disc is placed in upside down, “THIS TYPE OF DISC CANNOT BE PLAYED. PLEASE INSERT A DIFFERENT DISC” is displayed.

• Remove disc and press DECK POWER off when not in use.

• Disc continues to rotate with menu displayed even after play is done. Press STOP to clear menu display when finished with menu.

to resume play from this point.

STOP

again or opening the tray

Operation

Basic

D4734S-K P1-25 (040202).p65 2004/02/02, 15:1323

Timer Recording

Ready Checklist

All connections are made. (pp. 12 ~ 15) TV and DECK are plugged in. Clock set correctly. (p. 18) Tape has record tab intact. (p. 6) Remote is in VCR mode. (Press VCR.) Sufficient tape remaining for recording time.

Press PROG*

to display Program.

POWER

P DT START

1 -- --:-- --:-- --

2 -- --:-- --:-- --

3 -- --:-- --:-- -- 4 -- --:-- --:-- --

SELECT : EXIT

Example

Today

P DT START

1 13 2:00p 3:20p 02

2 -- --:-- --:-- -- 3 -- --:-- --:-- -- 4 -- --:-- --:-- --

CANCEL: SELECT : EXIT : PROG

STOP CH

SET : SET

: PROG

SELECT / Selection Order

WEEKLY

(SA)

STOP CH

SET COMPLETED

ADD/DLT

SET : SET

1) Press .

SPD

2) Set record DATE,

press

1~31= one time, or DAILY=Monday~Friday,

to select:

SELECT

SET VCR

or WEEKLY= same time each week.

ADD/DLT

• See selection order left.

3) Set remaining items,

DAILY

WEEKLY

(SU)

WEEKLY

(MO)

press SET

to set START/ STOP times, CH (channel) or LINE input (p. 35), and tape

PROG

speed (SP, SLP). Then press

to select.

Press PROG

to end programming.

VCR REC Indicator

To Enter More Programs,

SPD

SLP

press

to select and

press SET

to set an unused program number, and then repeat step 2.

Press PROG

to exit.

VCR mode Indicator

Multi Function Display

VCR

Hi - Fi

REC

A M

TIMER

TIMER Indicator

• The “Timer” Indicator lights up on DECK.

• You can set Timer Recording with the power on or off.

•“TIMER REC WILL START SOON” appears on-screen for 2 minutes

D4734S-K P1-25 (040202).p65 2004/02/02, 15:1324

before Timer Recording starts. If DECK is in DVD mode, no message appears, but the VCR REC Indicator, the VCR mode indicator and “REC” will flash on Multi function Display.

*Important: If a remote control button does not work when pressed,

press the VCR button on the remote and try the button again.

Review, Replace or Clear Program Contents:

(Recording is not in progress)

Press PROG

to display Program List.

P DT START

STOP CH

1 13 2:00p 3:20p 02

2 14 7:00p 7:30p 10

3 -- --:-- --:-- -- 4 -- --:-- --:-- --

CANCEL:

ADD/DLT

SET : SET

SELECT : EXIT : PROG

To Replace program...

P DT START

STOP CH

1 13 2:00p 3:20p 02

2 14

00p 7:30p 10 3 -- --:-- --:-4 -- --:-- --:--

SELECT : EXIT : PROG

To Clear program...

P DT START

1 -- --:-- --:-- --

2 14 7:00p 7:30p 10 3 -- --:-- --:-4 -- --:-- --:--

SELECT : EXIT

Press PROG

to end the programming.

SET : SET

STOP CH

SET : SET

: PROG

SPD

Press

SLP SP

to select number.

SPD

Repeat Step 2 (p. 24)

SLP

to set new programs.

Press ADD/DLT.

SPD

To cancel a Timer Recording in progress...

Hold down STOP in VCR mode for

a few seconds to cancel the Timer Recording.

( The “TIMER” Indicator goes out

on Multi Function Display.)

• Any future daily or weekly recording will be performed as programmed.

Operation

VCR

Notes

• If you are using a Cable Box, the VCR’s channel for Timer Recording must be set to the Cable Box input channel and Cable Box must be manually set to the desired channel. Cable Box power must be left on.

• 2 minutes before Timer Recording is performed, “PLEASE PREPARE FOR TIMER REC” appears and Timer Indicator flashes. Be sure a cassette with record tab is loaded and DECK is in Stop mode.

• If a power interruption occurs while programming the timer, the timer program(s) may be cancelled. If “TIMER PROGRAMS WERE LOST DUE TO POWER INTERRUPTION” appears on-screen, please re-enter the timer programs.

• If the start time for Timer Recording comes up during recording and playing back, Timer Recording will not be performed.

Important notes when using DSS Receiver

• When recording programs via DSS Receiver, DSS Receiver must be left on.

• When recording programs via an antenna or cable, DSS Receiver must be turned off.

D4734S-K P1-25 (040202).p65 2004/02/02, 15:1325

MTS Broadcast/ VHS Hi-Fi Stereo System

Connection

Make the Audio/Video Connection as shown on pp. 12 ~ 15.

• You can use TV connected to a Stereo amplifier and speakers instead of Stereo TV.

Receivable Broadcast Types

The following are possible audio broadcast types and onscreen displays.

The signal being received is indicated with a “ the selected audio mode is indicated with an arrow.

To display the broadcast signal being received,

➛➛

➛ press DISPLAY*.

➛➛

MTS Stereo and SAP broadcast

Multi-channel Television Sound Stereo (main language) and Secondary Audio Program (sub language) broadcasts are being received simultaneously. Select STEREO or SAP audio mode.

” mark while

STOP 1 2 : 0 0A

STER

EO SAP M

ONO

0 : 0 0 : 0 0

CH 02

MTS Stereo broadcast

Multi-channel Television Sound Stereo broadcast. Select STEREO audio mode.

• If stereo broadcast is weak and display flickers, select MONO audio mode for possible better results.

SAP broadcast

Secondary Audio Program (sub language) broadcast. Select SAP audio mode for the sub language.

MONO broadcast

Normal monaural sound broadcast.

STOP 1 2 : 0 0A

STER

EO SAP M

ONO

STOP 1 2 : 0 0A

STER

EO SAP M

ONO

STOP 1 2 : 0 0A

STER

EO SAP M

ONO

0 : 0 0 : 0 0

CH 02

AUDIO

(SAP/Hi-Fi)

DISPLAY

Equipped with ®-TV Noise Reduction for true MTS reproduction.

-TV Noise Reduction is required for good stereo

separation and audio fidelity.

is a registered trademark, and is licensed by

Technology Licensing.

D4734S-K P26-35 (040202).p65 2004/02/02, 15:1326

*Important: If a remote control button does not work when pressed,

press the VCR button on the remote and try the button again.

Audio Mode for Recording

Press AUDIO (SAP/Hi-Fi)

to display audio mode.

(Display disappears after 5 seconds.)

Press AUDIO (SAP/Hi-Fi) repeatedly

STER

EO SAP M

ONO

Make a recording.

See p. 21.

to select desired mode.

• Refer to “Receivable Broadcast Types” on p. 26.

• Arrow indicates selection.

Operation

Audio Mode for Playback

Start playback.

See p. 20.

Press AUDIO (SAP/Hi-Fi)

to display audio mode.

H I F I

: L / R H I F I

: L H I F I

ORM

• Arrow indicates selection.

Notes

• Only tapes recorded in Hi-Fi stereo will playback with true stereo sound. Standard stereo tapes will playback in monaural sound.

• To listen to Hi-Fi stereo playback, the DECK AUDIO (L/R) jacks must be connected to a stereo TV or an external stereo amplifier and speakers. (See pp. 12, 14.)

• If tracking is adjusted during playback, Hi-Fi audio may revert to normal audio.

• Hi-Fi and normal audio playback volume level may differ.

Press AUDIO (SAP/Hi-Fi) repeatedly to select desired mode.

• Select “HIFI (L/R)” or “HIFI (L)” or “HIFI (R)” to listen to stereo recordings in stereo sound. Select “NORMAL” for monaural sound.

• Display disappears after 5 seconds.

VCR

D4734S-K P26-35 (040202).p65 2004/02/02, 15:1327

Multi-Brand Control Feature

Multi-Brand Control Setup

The Remote Control can be set to control some TVs.

Find your TV Brand Code Number on the

following page.

Set up for TV control,

➛➛

➛ hold down TV button,

➛➛ ➛➛

➛ enter code with NUMBER keys.

➛➛

Confirm code entry,

➛ press POWER to turn selected unit on or off.

• See table below for controllable functions in each mode.

Notes

• Repeat setup after remote battery replacement.

• Remote will not control every TV made by the

manufacturer listed. If you get no response, your particular unit cannot be controlled. There are NO additional codes for the products listed. If your product is not listed, then the remote is not compatible with that product.

Using Multi-Brand Control

After remote is set up, you can select VCR, DVD, or TV for the desired function.

Press VCR,

(Table below shows available remote buttons for each mode.)

Mode

DVD VCR

DVD

, or TV on the remote.

Unit

EJECT/

DISPLAY, PLAY, STOP FF/SLOW+, REW/SLOW-

VCR/TV, PAUSE

AUDIO

TAPE POSITION, COUNTER RESET

DVD/VCR TV

OPEN/CLOSE

, CM/ZERO, SPEED, REC,

All

/STILL, SKIP

PAGE

POWER, INPUT, NUMBER keys, ENTER, CH / , VOL +/

VOL

* Bold: VCR Function

Italic: DVD Function

Notes

• Not all functions listed may be controllable.

• In TV mode, it may be necessary to press ENTER after pressing NUMBER keys

for channel selection.

Bold Italic: VCR and DVD Functions

Normal: TV

D4734S-K P26-35 (040202).p65 2004/02/02, 15:1328

TV Brand Code Numbers

Panasonic ......................................... 01, 02

Quasar.............................................. 01, 02

RCA ......................................................... 03

GE ........................................................... 03

Zenith ...................................................... 04

Magnavox ............................................... 05

Sylvania .................................................. 05

Sharp................................................. 06, 07

Sony ........................................................ 08

Toshiba ................................................... 09

Sanyo ...................................................... 10

Fisher...................................................... 10

JVC ......................................................... 11

Hitachi ..................................................... 12

Mitsubishi .......................................... 07, 13

Samsung ................................................ 14

Gold Star .................................... 15, 16, 17

Important Notes

• Some manufacturers use several codes for one brand. If the first code entered fails, try the next one listed.

• Some TVs require you to turn on the power manually.

Operation

POWER

VCR

NUMBER keys

DVD

ENTER

VCR

D4734S-K P26-35 (040202).p65 2004/02/02, 15:1329

Tape Operation

Search System

For each recording, an invisible index mark is placed on the tape. A program index and information are also included for timer recordings. These marks are used to access or scan recordings.

Index Search

INDEX SEARCH

ENTER INDEX NUMBER :1

USING 1- 9 KEYS

FORWARD SEARCH :FF REVERSE SEARCH :REW

EXIT :SEARCH

INDEX SEARCH

FORWARD SEARCH : FF REVERSE

To Calculate Index Number

Example 1:

To go to rec. 2 from rec. 4, enter 3 and press REW.

Example 2:

To go to rec. 6 from rec. 2, enter 4 and press FF.

SEARCH : REW

Press SEARCH*

to display SEARCH in Stop or Play mode, and then

press NUMBER keys to select

recording number.

• To calculate number, see below.

Press FF/SLOW+

or REW/SLOW- on the remote to start search.

Play begins at search end. To search forward or back 1 index,

press FF/SLOW+ or REW/SLOW- on the

remote while screen left is displayed (10 sec.).

• To cancel, press PLAY or STOP.

61572 34

Zero Search

To quickly return to a specified tape location.

Press DISPLAY during play

to display Counter.

PLAY

1 2 : 0 0A

0 : 0 0 : 0 0

Press COUNTER

RESET on remote at desired position to reset to “0:00:00”.

Continue to record, playback etc.

Press STOP.

REW

1 2 : 3 0A

M CH 02

Press CM/ZERO

0 : 30 : 30

in Stop mode to start Zero Search.

STOP

1 2 : 3 1AM CH 02

0 : 0 0 : 0 0

• DECK will go into FF or REW mode and stop at the last point the Counter was set to 0:00:00.

Commercial Skip

DECK fast forwards (skips) over 1, 2, or 3 minutes of recorded tape as desired.

Press CM/ZERO in Play mode.

• The skip time can be changed by pressing CM/ZERO repeatedly as shown by the figure below.

PLAY

1st Press

1 min Skip

17534 62

NOTE: indicates start points of each recording.

Note

• If Index Search is started very close to an index mark, that index mark may not be counted in the search.

D4734S-K P26-35 (040202).p65 2004/02/02, 15:1330

2nd Press

3rd Press

• No indication appears on-screen.

2 min Skip

3 min Skip

+ 98 hidden pages