Panasonic pt-dz770 Operation Manual

Operating Instructions

Functional Manual

DLPTM Projector

Model No.

 PT-DZ770U

Commercial Use

 PT-DZ770UL

Thank you for purchasing this Panasonic product.

■ This manual is common to all the models regardless of sufxes of the Model No.

zS: Silver model, the standard zoom lens supplied LS: Silver model, the lens sold separately

K: Black model, the standard zoom lens supplied LK: Black model, the lens sold separately

■ Before operating this product, please read the instructions carefully and save this manual

for future use.

■ Before using your projector,

be sure to read “Read this rst!” ( pages 2 to 10).

ENGLISH

TQBJ0442-1

Information

Read this rst!

Information

Important

WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DONOT EXPOSE THIS PRODUCT

CAUTION: This equipment is equipped with a three-pin grounding-type power

CAUTION: To assure continued compliance, follow the attached installation instructions, which include using

TO RAIN OR MOISTURE.

The lightning ash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufcient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product.

plug. Do not remove the grounding pin on the power plug. This plug will only t a grounding-type power outlet. This is a safety feature. If you are unable to insert the plug into the outlet, contact an electrician. Do not defeat the purpose of the grounding plug.

the provided power cord and shielded interface cables when connecting to computer or peripheral device. If you use serial port to connect PC for external control of projector, you must use optional RS-232C serial interface cable with ferrite core. Any unauthorized changes or modications to this equipment will void the user’s authority to operate.

Do not remove

2 - ENGLISH

Read this rst!

FCC NOTICE (USA)

Verication

Model Number: PT-DZ770US / PT-DZ770UK / PT-DZ770ULS / PT-DZ770ULK Trade Name: Panasonic Responsible Party: Panasonic Corporation of North America Address: One Panasonic Way, Secaucus, NJ 07094 Telephone number: (877)803-8492 E-mail: projectorsupport@us.panasonic.com This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. To assure continued compliance, follow the attached installation instructions and do not make any unauthorized modications.

CAUTION:

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

Important

Information

NOTIFICATION (Canada)

This class A digital apparatus complies with Canadian ICES-003.

WARNING:

zNot for use in a computer room as dened in the Standard for the Protection of Electronic Computer/Data

Processing Equipment, ANSI/NFPA 75.

zFor permanently connected equipment, a readily accessible disconnect device shall be incorporated in the

building installation wiring.

zFor pluggable equipment, the socket-outlet shall be installed near the equipment and shall be easily

accessible.

NOTICE (USA only):

zThis product has a High Intensity Discharge (HID) lamp that contains mercury. Disposal may be regulated

in your community due to environmental considerations. For disposal or recycling information, please visit Panasonic website: http://www.panasonic.com/environmental or call 1-888-769-0149.

For USA-California Only

This product contains a CR Coin Cell Lithium Battery which contains Perchlorate Material – special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate

ENGLISH - 3

Read this rst!

Information

Important

WARNING:

The wall outlet or the circuit breaker shall be installed near the equipment and shall be easily accessible when problems occur. If the following problems occur, cut off the power supply immediately.

Continued use of the projector in these conditions will result in re or electric shock.

During a thunderstorm, do not touch the projector or the cable.

Electric shocks can result.

Do not do anything that might damage the power cord or the power plug.

If the power cord is used while damaged, electric shocks, short-circuits or re will result.

Completely insert the power plug into the wall outlet and the power connector into the projector terminal.

If the plug is not inserted correctly, electric shocks or overheating will result.

Do not use anything other than the provided power cord.

Failure to observe this will result in re or electric shocks. Please note that if you do not use the provided power cord to ground the device on the side of the outlet, this may result in electric shocks.

Clean the power plug regularly to prevent it from becoming covered in dust.

Failure to observe this will cause a re.

Do not handle the power plug and power connector with wet hands.

Failure to observe this will result in electric shocks.

Do not overload the wall outlet.

If the power supply is overloaded (ex., by using too many adapters), overheating may occur and re will result.

POWER

zIf foreign objects or water get inside the projector, cut off the power supply. zIf the projector is dropped or the cabinet is broken, cut off the power supply. zIf you notice smoke, strange smells or noise coming from the projector, cut off the power supply.

Please contact an Authorized Service Center for repairs, and do not attempt to repair the projector yourself.

zDo not damage the power cord, make any modications to it, place it near any hot objects, bend it

excessively, twist it, pull it, place heavy objects on top of it or wrap it into a bundle.

Ask an Authorized Service Center to carry out any repairs to the power cord that might be necessary.

zDo not use plugs which are damaged or wall outlets which are coming loose from the wall.

zIf dust builds up on the power plug, the resulting humidity can damage the insulation.

Pull the power plug out from the wall outlet and wipe it with a dry cloth regularly.

ON USE/INSTALLATION

Do not place the projector on soft materials such as carpets or sponge mats.

Doing so will cause the projector to overheat, which can cause burns, re or damage to the projector.

Do not set up the projector in humid or dusty places or in places where the projector may come into contact with oily smoke or steam, ex. a bathroom.

Using the projector under such conditions will result in re, electric shocks or deterioration of components. Deterioration of components (such as ceiling mount brackets) may cause the projector which is mounted on the ceiling to fall down.

Do not install this projector in a place which is not strong enough to take the full weight of the projector or on top of a surface which is sloped or unstable.

Failure to observe this will cause projector to fall down or tip over the projector, and severe injury or damage could result.

4 - ENGLISH

Read this rst!

WARNING:

Do not cover the air intake/exhaust ports or place anything within 500 mm (20") of them.

Doing so will cause the projector to overheat, which can cause re or damage to the projector.

zDo not place the projector in narrow, badly ventilated places. zDo not place the projector on cloth or papers, as these materials could be drawn into the air inlet port.

Do not place your hands or other objects close to the air exhaust port.

Doing so will cause burns or damage your hands or other objects.

zHeated air comes out of the air exhaust port. Do not place your hands or face, or objects which cannot

withstand heat close to this port.

Do not look at or place your skin into the light emitted from the lens while the projector is being used.

Doing so can cause burns or loss of sight.

zStrong light is emitted from the projector’s lens. Do not look at or place your hands directly into this light. zBe especially careful not to let young children look into the lens. In addition, turn off the power and

disconnect the power plug when you are away from the projector.

Never attempt to remodel or disassemble the projector.

High voltages can cause re or electric shocks.

zFor any inspection, adjustment and repair work, please contact an Authorized Service Center.

Do not project an image with the lens cover attached.

Doing so can cause re.

Do not allow metal objects, ammable objects, or liquids to enter inside of the projector. Do not allow the projector to get wet.

Doing so may cause short circuits or overheating, and result in re, electric shock, or malfunction of the projector.

zDo not place containers of liquid or metal objects near the projector. zIf liquid enters inside of the projector, consult your dealer. zParticular attention must be paid to children.

Use the ceiling mount bracket specied by Panasonic.

Using the ceiling mount bracket other than the specied one will result in falling accidents.

zAttach the supplied safety cable to the ceiling mount bracket to prevent the projector from falling down.

Installation work (such as ceiling mount bracket) should only be carried out by a qualied technician.

If installation is not carried out and secured correctly it can cause injury or accidents, such as electric shocks.

zDo not use anything other than an authorized ceiling mount bracket. zBe sure to use the provided accessory wire with an eye bolt as an extra safety measure to prevent the

projector from falling down. (Install in a different location to the ceiling mount bracket.)

Important

Information

ENGLISH - 5

Read this rst!

Information

Important

WARNING:

Do not use or handle the batteries improperly, and refer to the following.

Failure to observe this will cause burns, batteries to leak, overheat, explode or catch re.

If the battery uid leaks, do not touch it with bare hands, and take the following measures if necessary.

Do not disassemble the lamp unit.

Doing so can cause electric shocks, burns, or injury.

Lamp replacement

The lamp has high internal pressure. If improperly handled, an explosion and severe injury or accidents will result.

Do not use the supplied power cord with devices other than this projector.

Remove the depleted batteries from the remote control promptly.

ACCESSORIES

zUse AA/R6 batteries. zDo not use unspecied batteries. zDo not use chargeable batteries. zDo not disassemble dry cell batteries. zDo not heat the batteries or place them into water or re. zDo not allow the + and – terminals of the batteries to come into contact with metallic objects such as

necklaces or hairpins. zDo not store batteries together with metallic objects. zStore the batteries in a plastic bag and keep them away from metallic objects. zMake sure the polarities (+ and –) are correct when inserting the batteries. zDo not use a new battery together with an old battery or mix different types of batteries. zDo not use batteries with the outer cover peeling away or removed.

zBattery uid on your skin or clothing could result in skin inammation or injury.

Rinse with clean water and seek medical advice immediately. zBattery uid coming in contact with your eyes could result in loss of sight.

In this case, do not rub your eyes. Rinse with clean water and seek medical advice immediately.

zThe lamp can easily explode if struck against hard objects or dropped. zBefore replacing the lamp, be sure to turn the power off and to disconnect the power plug from the wall

outlet.

Electric shocks or explosions can result if this is not done. zWhen replacing the lamp, turn the power off and allow it to cool for at least one hour before handling it

otherwise it can cause burns.

zUsing the supplied power cord with devices other than this projector may cause short circuits or

overheating, and result in electric shock or re.

zLeaving them in the unit may result in uid leakage, overheating, or explosion of the batteries.

6 - ENGLISH

Read this rst!

CAUTION:

POWER

When disconnecting the power cord, be sure to hold the power plug and power connector.

If the power cord itself is pulled, the lead will become damaged, and re, short-circuits or serious electric shocks will result.

When not using the projector for an extended period of time, disconnect the power plug from the wall outlet.

Failure to do so may result in re or electric shock.

Disconnect the power plug from the wall outlet before carrying out any cleaning and replacing the unit.

Failure to do so may result in electric shock.

ON USE/INSTALLATION

Do not place heavy objects on top of the projector.

Failure to observe this will cause the projector to become unbalanced and fall, which could result in damage or injury. The projector will be damaged or deformed.

Do not put your weight on this projector.

You could fall or the projector could break, and injury will result.

zBe especially careful not to let young children stand or sit on the projector.

Do not place the projector in extremely hot locations.

Doing so will cause the outer casing or internal components to deteriorate, or result in re.

zTake particular care in locations exposed to direct sunlight or near stoves.

Do not place your hands in the openings beside the optical lens, while shifting the lens.

Failure to observe this could cause injury.

Do not stand in front of the lens while the projector is being used.

Doing so can cause damage and burns to clothing.

zStrong light is emitted from the projector’s lens.

Do not place objects in front of the lens while the projector is being used.

Doing so can cause damage to the object and can cause the set to malfunction.

zStrong light is emitted from the projector’s lens.

Always disconnect all cables before moving the projector.

Moving the projector with cables still attached can damage the cables, which will cause re or electric shocks to occur.

Important

Information

ENGLISH - 7

Read this rst!

Information

Important

CAUTION:

Do not use the old lamp unit.

If used it could cause lamp explosion.

If the lamp has broken, ventilate the room immediately. Do not touch or bring your face close to the broken pieces.

Failure to observe this will cause the user to absorb the gas which was released when the lamp broke and which contains nearly the same amount of mercury as uorescent lamps, and the broken pieces will cause injury.

Do not attach the air lter unit while it is wet.

Doing so may result in electric shock or malfunctions.

Do not touch the fan with your ngers or any other parts of your body when changing the lamp unit.

Doing so can cause injury.

Ask your dealer about cleaning inside the projector once a year.

Continuous use while dust is accumulated inside the projector may result in re.

When not using the projector for an extended period of time, remove the batteries from the remote control.

Failure to observe this will cause the batteries to leak, overheat, catch re or explode, which may result in re or contamination of surrounding area.

ACCESSORIES

zIf you believe that you have absorbed the gas or that the gas has got into your eyes or mouth, seek

medical advice immediately. zAsk your dealer about replacing the lamp unit and check the inside of the projector.

zAfter you clean the air lter units, dry them thoroughly before reattaching them.

zFor cleaning fee, ask your dealer.

8 - ENGLISH

Brazil Only Brasil Apenas

Read this rst!

Manuseio de baterias usadas

BRASIL

Após o uso, as pilhas e /ou baterias poderão ser entregues ao estabelecimento comercial ou rede de assistência técnica autorizada.

Cobrir os terminais positivo (+) e negativo (-) com uma ta isolante adesiva, antes de depositar numa caixa destinada para o recolhimento. O contato entre partes metálicas pode causar vazamentos, gerar calor, romper a blindagem e produzir fogo. Não desmonte, não remova o invólucro, nem amasse a bateria. O gás liberado pela bateria pode irritar a garganta, danicar o lacre do invólucro ou o vazamento provocar calor, ruptura da blindagem e produzir fogo devido ao curto circuito dos terminais. Não incinere nem aqueça as baterias, elas não podem car expostas a temperaturas superiores a 100 °C (212 °F). O gás liberado pela bateria pode irritar a garganta, danicar o lacre do invólucro ou o vazamento provocar calor, ruptura da blindagem e produzir fogo devido ao curto circuito dos terminais provocado internamente. Evite o contato com o liquido que vazar das baterias. Caso isto ocorra, lave bem a parte afetada com bastante água. Caso haja irritação, consulte um médico.

Remoção das baterias

Important

Information

1. Pressione a guia e levante a tampa.

(ii)

(i)

2. Remova as baterias.

ENGLISH - 9

Read this rst!

Information

Important

Trademarks

• Microsoft®, Windows®, Windows Vista®, and Internet Explorer® are the registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries.

• Mac, Mac OS, Mac OSX, and Safari are the trademarks of Apple Inc. registered in the United States and other countries.

• PJLinkTM is a trademark or pending trademark in Japan, the United States, and other countries and regions.

• HDMI, the HDMI logo and High-Denition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC.

• VGA and XGA are trademarks of International Business Machines Corporation.

• SVGA is a registered trademark of the Video Electronics Standards Association.

• RoomView, Crestron RoomView, Crestron Connected, and Fusion RV are trademarks of Crestron Electronics, Inc.

• The font used in the on-screen displays is a Ricoh bitmap font, which is manufactured and sold by Ricoh Company, Ltd.

• Adobe Flash Player is either a trademark or registered trademark of Adobe Systems Incorporated in the United States and/or other countries.

• Other names, company names or product names used in these operating instructions are the trademarks or registered trademarks of their respective holders. Please note that the operating instructions do not include the ® and TM symbols.

Illustrations in these operating instructions

• Note that illustrations of the projector and screens may differ from the ones you actually see.

Page references

• In these instructions, references to pages are indicated as: ( page 00).

Term

• In these instructions, the “Wireless/wired remote control unit” accessories are referred to as the “Remote control”.

10 - ENGLISH

Quick StepsQuick Steps

Features of the ProjectorFeatures of the Projector

High luminance & High color

For details, see the corresponding pages.

reproducibility

The unique optical system and

▶

lamp drive system achieve a high luminance and high color reproducibility.

Easy setup and improved serviceability

Extensive lineup of optional lenses

▶

allow more exible setup of the projector.

Improved cost performance in maintenance fee

The long-life lter reduces the

▶

maintenance cost.

1. Set up the projector. ( page 25)

2. Attach the projection lens. ( page 33)

3. Connect with other devices. (

page 34)



4. Connect the power cord. ( page 37)

5. Switch on the projector. ( page 39)

6. Make initial settings.

( page 20)

7. Select the input signal. ( page 41)

8. Adjust the image. ( page 41)

*1: These are the steps to be taken when you switch on the

power for the rst time after purchasing the projector.

ENGLISH - 11

Contents

Be sure to read “Read this rst!”. (



pages

2 to 10)

Information

Important

Important Information

Read this rst! ............................................ 2

Precautions for use ...................................14

Preparation Getting Started Basic Operation Settings Maintenance Appendix

Preparation

Start-up display ........................................ 20

About your projector .................................21

Using the remote control ......................... 24

Getting Started

Setting up .................................................. 25

Removing/attaching a projection lens ..... 32

Connections ............................................. 34

Basic Operation

Switching on/off the projector ................. 37

Projecting...................................................41

Cautions when transporting ............................. 14

Cautions when installing .................................. 14

Security ...........................................................16

Disposal .......................................................... 16

Cautions on use .............................................. 17

Accessories ....................................................18

Optional accessories .......................................19

Remote control ................................................ 21

Projector body .................................................22

Inserting and removing the batteries ................24

Setting Remote control ID numbers .................24

Connecting to the projector with a cable ..........24

Projection method ...........................................25

Parts for ceiling mount (optional) .....................25

Screen size and throw distance ....................... 26

Adjusting adjustable feet .................................31

Removing the projection lens ..........................32

Attaching the projection lens ............................ 33

Before connecting to the projector ................... 34

Connecting example: AV equipment ................35

Connecting example: Computers .....................36

Connecting the power cord .............................. 37

Power indicator ...............................................38

Switching on the projector ............................... 39

Making adjustments and selections ................. 39

Switching off the projector ...............................40

Direct power off function .................................. 40

Selecting the input signal ................................. 41

Adjusting the focus, zoom, and shift ................41

Moving the lens to the home position ............... 42

Adjustment range by the lens position shift

(optical shift) .............................................42

Remote control operation ........................ 43

Using the shutter function ................................43

Using the on-screen display function ............... 43

Switching the input signal ................................43

Using the STATUS function ............................. 43

Using the Automatic setup function ..................44

Using the Function button ................................44

Displaying the internal test pattern ...................44

Changing the picture aspect ratio ....................45

Settings

Menu navigation ....................................... 46

Navigating through the menu ...........................46

Main menu ......................................................47

Sub-menu .......................................................47

[PICTURE] menu ....................................... 49

[PICTURE MODE] ...........................................49

[CONTRAST] ..................................................49

[BRIGHTNESS] ...............................................49

[COLOR] .........................................................50

[TINT] .............................................................. 50

[COLOR TEMPERATURE] .............................. 50

[WHITE GAIN] ................................................. 51

[SYSTEM DAYLIGHT VIEW] ........................... 51

[SHARPNESS] ................................................ 51

[NOISE REDUCTION] ..................................... 51

[AI] .................................................................52

[SYSTEM SELECTOR] ................................... 52

[POSITION] menu ..................................... 53

[SHIFT] ...........................................................53

[ASPECT] .......................................................53

[ZOOM] ...........................................................54

[CLOCK PHASE] .............................................55

[KEYSTONE] ..................................................55

[ADVANCED MENU] ................................. 56

[DIGITAL CINEMA REALITY]...........................56

[BLANKING] ....................................................56

[INPUT RESOLUTION] ....................................57

[CLAMP POSITION] ........................................57

[EDGE BLENDING] .........................................57

[RASTER POSITION] ...................................... 58

[DISPLAY LANGUAGE] menu .................. 59

Changing the display language ........................59

[DISPLAY OPTION] menu ......................... 60

[COLOR MATCHING] ......................................60

[COLOR CORRECTION] .................................61

[CONTRAST MODE] ....................................... 61

[SCREEN SETTING] .......................................62

12 - ENGLISH

Contents

[AUTO SIGNAL] .............................................. 62

[AUTO SETUP] ...............................................62

[RGB IN] .........................................................63

[DVI-D IN] ........................................................63

[HDMI IN] ........................................................64

[ON-SCREEN DISPLAY] .................................64

[BACK COLOR] ..............................................65

[STARTUP LOGO] .......................................... 65

[SHUTTER SETTING] .....................................66

[FREEZE] ........................................................66

[SIDE BY SIDE] ...............................................66

[CUT OFF] ......................................................67

[PROJECTOR SETUP] menu .................... 68

[PROJECTOR ID] ............................................ 68

[PROJECTION METHOD] ............................... 68

[COOLING CONDITION] ................................. 69

[HIGH ALTITUDE MODE] ................................69

[LAMP SELECT] .............................................69

[LAMP RELAY] ................................................70

[LAMP POWER] ..............................................70

[STANDBY MODE] .......................................... 70

[SCHEDULE] ................................................... 71

[STARTUP INPUT SELECT] ............................ 72

[RS-232C] .......................................................72

[REMOTE2 MODE] .........................................73

[STATUS] ........................................................ 74

[NO SIGNAL SHUT-OFF] ................................75

[FUNCTION BUTTON] ....................................75

[DATE AND TIME] ........................................... 75

[SAVE ALL USER DATA] ................................. 76

[LOAD ALL USER DATA] ................................76

[INITIALIZE].....................................................76

[SERVICE PASSWORD] .................................76

[TEST PATTERN] menu ............................ 77

[TEST PATTERN] ............................................77

[SIGNAL LIST] menu ................................ 78

Registering a signal to the list .......................... 78

Renaming the registered data .........................78

Deleting a registered data................................78

Protecting the registered data ..........................79

Expanding signal lock-in range ........................79

Managing the sub memory list ......................... 80

[SECURITY] menu .....................................81

[SECURITY PASSWORD] ............................... 81

[SECURITY PASSWORD CHANGE] ............... 81

[DISPLAY SETTING] ....................................... 81

[TEXT CHANGE] .............................................82

[MENU LOCK] .................................................82

[MENU LOCK PASSWORD] ...........................82

[CONTROL DEVICE SETUP] .......................... 82

[NETWORK] menu .................................... 84

[NETWORK SETUP] .......................................84

[NETWORK CONTROL] .................................84

[NETWORK STATUS] .....................................84

Network connections .......................................85

Accessing from the Web browser ....................87

Maintenance

Lamp/Temperature/Filter Indicators .......104

Managing the indicated problems .................. 104

Maintenance/replacement .......................106

Before maintaining/replacing the unit ............. 106

Maintenance ................................................. 106

Replacing the unit .......................................... 107

Troubleshooting ...................................... 110

Appendix

Technical information ..............................112

PJLink protocol .............................................. 112

Control commands via LAN ........................... 113

<SERIAL IN>/<SERIAL OUT> terminal .......... 115

<REMOTE 2 IN> terminal .............................. 118

Two window display combination list .............. 119

Menu lock password...................................... 119

List of compatible signals ............................... 120

Specications ..........................................122

Dimensions ..............................................124

Ceiling mount bracket safeguards .........124

Index ........................................................125

Important

Information

PreparationGetting StartedBasic OperationSettingsMaintenanceAppendix

ENGLISH - 13

Precautions for use

Information

Important

Cautions when transporting

Cautions when installing

zThe projection lens is susceptible to effects from vibration or impact. Make sure to remove the lens when

transporting. Use a protective cover to avoid the effects of dust to the set or projection lens.

zWhen transporting the projector, hold it securely by its bottom and avoid excessive vibration and impacts. They

may damage the internal parts and result in malfunctions.

zDo not transport the projector with the adjustable feet extended. Doing so may damage the adjustable feet.

■Always attach the projection lens cover after attaching the projection lens.

If the cover is not attached, dust will accumulate inside and may cause malfunctions.

■Do not set up the projector outdoors.

The projector is designed for indoor use only.

■Do not set up the projector in the following locations.

Places where vibration and impacts occur such as in a car or vehicle: Doing so may cause damage to



internal parts or malfunction. Near the exhaust of an air conditioner: Depending on the conditions of use, the screen may uctuate in rare



cases due to the hot air from the air exhaust port or the heated or cooled air. Make sure that the exhaust from the projector or other equipment, or the air from the air conditioner does not blow toward the front of the projector. Near lights (studio lamps, etc.) and other locations of great temperature uctuation (“Operating



environment” ( case and malfunctions. Near high-voltage power lines or near motors: Doing so may interfere with the operation of the projector.



Place where there is high-power laser equipment: Directing a laser beam onto the lens surface causes



damage to the DLP chips.

page 123)): Doing so may shorten the life of the lamp or result in deformation of the outer



■Be sure to ask a specialized technician or your dealer when installing the product to a ceiling.

If the product is to be installed hanging from the ceiling, purchase an optional Ceiling Mount Attachment. Model No.: ET-PKD56H (for high ceilings), ET-PKD55S (for low ceilings)

■Lens focus

The high clarity projection lens is thermally affected by the light from the light source, making the focus unstable in the period just after switching on the power. Wait at least 30 minutes with the image projected before adjusting the lens focus.

■Make sure to set [HIGH ALTITUDE MODE] to [ON] when using the projector at elevations of 1 400 m (4 593 ft) or higher and lower than 2 700 m (8 858 ft) above sea level.

Doing so may shorten the life of the internal parts and result in malfunctions.

■Make sure to set [HIGH ALTITUDE MODE] to [OFF] when using the projector at elevations lower than 1 400 m (4 593 ft) above sea level.

Doing so may shorten the life of the internal parts and result in malfunctions.

■Do not install the projector at elevations of 2 700 m (8 858 ft) or higher above sea level.

Doing so may shorten the life of the internal parts and result in malfunctions.

■Do not use the projector tilted to the right or left.

Using the projector at a vertical angle that exceeds 15° may reduce product life or result in malfunction.

■When installing and using the projector at an angle that exceeds 30° vertically, set [COOLING CONDITION] (

Failure to observe this will result in malfunctions or shorten the life of the lamp or other components.

14 - ENGLISH

page 69).



Precautions for use

Screw holes for ceiling mount (M6)

500 mm (20") or longer 500 mm (20") or longer 500 mm (20") or longer

■Cautions when setting up the projector

To install and use the projector via a method that does not use the adjustable feet in a oor standing



installation, x the projector using the ve screw holes for ceiling mounting (as shown in the diagram). (Screw diameter: M6, tapping depth inside the set: 12 mm (15/32"), torque: 4 ± 0.5 N·m) Use the adjustable feet only for the oor standing installation and for adjusting the angle. Using it for other



purposes may damage the set.

Adjustable feet

Important

Information

Do not stack projectors on top of each other.



Do not use the projector tilted at an angle that exceeds ±15° from the horizontal plane.



Do not block the ventilation ports (intake and exhaust) of the projector.



Prevent hot and cool air from the air conditioning system to blow directly to the ventilation ports (intake and



exhaust) of the projector.

100 mm (4") or longer

Do not install the projector in a conned space.



When it is necessary to install the projector in a conned space, install the air conditioning or ventilation separately. Exhaust heat may accumulate when the ventilation is not enough, triggering the protection circuit of the projector. Make a clearance of at least 20 mm (0.8") between the projector bottom and setting surface by inserting



spacers (metallic) etc. between them.

ENGLISH - 15

Precautions for use

Information

Important

Security

When using this product, take safety measures against the following incidents.

Take sufcient security measures. ( pages 81, 100)

Disposal

To dispose of the product, ask your local authorities or dealer for correct methods of disposal. The lamp contains mercury. When disposing of used lamp units, contact your local authorities or dealer for correct methods of disposal.

Personal information being leaked via this product



Unauthorized operation of this product by a malicious third party



Interfering or stopping of this product by a malicious third party



Make your password difcult to guess as much as possible.



Change your password periodically.



Panasonic Corporation or its afliate companies will never ask for your password directly. Do not divulge



your password in case you receive such inquiries. The connecting network must be secured by a rewall, etc.



Set a password for the web control and restrict the users who can log in.



16 - ENGLISH

Precautions for use

Cautions on use

■To get a good picture quality

In order to view a beautiful image in higher contrast, prepare an appropriate environment. Draw curtains or blinds over windows and turn off any lights near the screen to prevent outside light or light from indoor lamps from shining onto the screen.

■Do not touch the surface of the projection lens with your bare hands.

If the surface of the projection lens becomes dirty from ngerprints or anything else, this will be magnied and projected onto the screen. Please put the lens cover (accessory) on the projector when you do not use it.

■DLP chips

The DLP chips are precision-made. Note that in rare cases, pixels of high precision could be missing or



always lit. Note that such phenomena does not indicate malfunction. Directing a high-power laser beam onto the lens surface can damage the DLP chips.



■Do not move the projector while it is operating or subject it to vibration or impact.

Doing so may shorten the service life of its internal components.

■Lamp

The luminous source of the projector is a high-pressure mercury lamp. A high-pressure mercury lamp has the following characteristics.

The luminance of the lamp will decrease by duration of usage.



The lamp may burst with a loud sound or have its service life shortened because of shock, chipping, or



degradation due to cumulative operating time. The lamp life varies greatly depending on individual differences and usage conditions. In particular,



frequently switching the power on/off accelerates lamp deterioration and greatly affects lamp life. Continuous use for over 1 week will deteriorate the lamp. The degradation of the lamp due to continuous



usage can be reduced by lamp relay function. ( page 70) In rare cases, the lamps burst shortly after projection starts.



The risk of bursting increases when the lamp is used beyond its replacement cycle. Make sure to replace



the lamp unit regularly. (“When to replace the lamp unit” ( page 108), “Replacing the lamp unit” ( page 109)) If the lamp bursts, gas contained inside of the lamp is released in a form of smoke.



It is recommended that you store replacement lamp units for contingency.



Important

Information

This product is equipped with the following software: (1) Software which is developed independently by or for Panasonic Corporation (2) Software which is licensed under GNU GENERAL PUBLIC LICENSE (3) Software which is licensed under GNU LESSER GENERAL PUBLIC LICENSE For license conditions related to software in (2) and (3), refer to the provisions of the software licenses (GNU GENERAL PUBLIC LICENSE and GNU LESSER GENERAL PUBLIC LICENSE) in the supplied CD-ROM. If you have any questions regarding the software, please contact us via email (sav.pj.gpl.pavc@ml.jp.panasonic.com).

ENGLISH - 17

Precautions for use

Information

Important

Accessories

Make sure that the following accessories are provided with your projector. Numbers enclosed in < > show the number of accessories.

Wireless/wired remote control unit <1> (N2QAYB000784)

CD-ROM <1> (TXFQB02VLC9)

Power cord <1> (K2CG3YY00075)

Power cord secure lock (TTRA0182)

Projection lens cover <1> (TKPB35101)

<1>

AA/R6 battery <2>

Lens cover <1> (TKKL5244)

(for models with attached

lenses only)

(For remote control unit)

Attention

zAfter unpacking the projector, discard the power cord cap and packaging material properly. zFor missing accessories, consult your dealer. zStore small parts in an appropriate manner, and keep them away from small children.

Note

zThe model numbers of accessories and optional components are subject to change without notice.

18 - ENGLISH

■Contents of the supplied CD-ROM

The contents of the supplied CD-ROM are as follows.

Instruction/list (PDF) Software

Precautions for use

Operating Instructions - Functional



Manual

Multi Projector Monitoring & Control



Multi Projector Monitoring & Control



Software (Windows)

This software allows you to monitor and control



multiple projectors connected to the LAN.

Software Operation Manual

Logo Transfer Software (Windows)

Logo Transfer Software Operating



Instructions

List of Compatible Projector Models



This is a list of projectors that are compatible with



the software contained in the CD-ROM and their restrictions.

Software license



(GNU GENERAL PUBLIC LICENSE, GNU LESSER GENERAL PUBLIC LICENSE)



This software allows you to create original



images, such as company logos to be displayed when projection starts, and transfer them to the projector.

Optional accessories

Optional accessories (product name)

Projection lens

Ceiling mount bracket ET-PKD56H (for high ceilings), ET-PKD55S (for low ceilings)

Replacement lamp unit ET-LAD60A (1 pc), ET-LAD60AW (2 pcs)

Replacement lter unit ET-EMF300

Model No.

ET-DLE055 (Fixed-focus lens), ET-DLE080 (Ultra-short focus zoom lens), ET-DLE150 (Short focus zoom lens), ET-DLE250 (Medium focus zoom lens), ET-DLE350 (Long focus zoom lens), ET-DLE450 (Ultra-long focus zoom lens)

Important

Information

ENGLISH - 19

Start-up display

The initial setting screen is displayed when the projector is switched on for the rst time after purchase as well as when [INITIALIZE] – [ALL USER DATA] ( page 76) is executed. Set them in accordance with circumstances. In other occasions, you can change the settings by menu operations.

Note

zWhen the projector is used for the rst time, you may be required to adjust the focus, zoom, and shift to display

the menu screen clearly. Refer to “Adjusting the focus, zoom, and shift” (

page 41) for details.



Preparation

Select the language to show on the screen.( page 59)

1) Press

2) Press the <ENTER> button to proceed

Initial setting (display language)

■

to select the display



language.

,1,7,$/6(77,1*

3/($6(6(/(&7/$1*8$*(

6(/(&7

(17(5

6(7

to the initial setting.

Initial setting (projector setup)

■

Set each item.

1) Press

2) Press

INITIAL SETTING

PROJECTION METHOD

COOLING CONDITION

SCREEN FORMAT

SCREEN POSITION

HIGH ALTITUDE MODE

SWITCH TO HIGH ALTITUDE MODE "ON"

IF OVER 1400m (4593Ft).

ENTER

to select an item.



to switch the setting.

󱽃󱽄

FRONT/FLOOR

FLOOR SETTING

MENU SELECT CHANGE

SET

16㧦10

OFF

Refer to the following page for details of each item.

[PROJECTION METHOD] ( page 68)



[COOLING CONDITION] ( page 69)



[SCREEN FORMAT] ( page 62)



[SCREEN POSITION] ( page 62)



[HIGH ALTITUDE MODE] ( page 69)



3) Press the <ENTER> button.

Conrm the setting value to complete the initial



setting.

Note

zIf you press the <MENU> button in the initial setting

(projector setup) screen, you can go back to the initial setting (display language) screen.

20 - ENGLISH

About your projector

Remote control signal transmitter

Remote control wired terminal

Remote control

About your projector

Top

■

Front

■

(1)

(2)

(3)

(4)

(5)

(6)

(7)

(8)

(9)

Bottom

■

( page 24)

(1) Remote control indicator

Flashes if any button in the remote control is pressed.

(2)

Power standby <

Sets the projector to the standby mode when the <MAIN POWER> switch on the projector is set to <ON>.

(3)

Power on <

Starts projection when the <MAIN POWER> switch on the projector is set to <ON> when the power is switched off (standby mode).

(4) Input selection (<RGB1>, <RGB2>, <DVI-D>, <VIDEO>, <S-VIDEO>, <HDMI>)

buttons

Switches the input signal to project.(

(5) <MENU> button/<ENTER> button/

Used to operate the menu screen.(

(6) <ON SCREEN> button

Switches the on-screen display function on (displayed)/off (hidden).(

(7) <TEST PATTERN> button

(10)

(11)

(12)

(13)

(14)

(15)

(16) (17)

Displays the test pattern.(

(8) Number (<0> - <9>) buttons

Used when the system uses multiple projectors. Used to input ID numbers or passwords.

(9) <STATUS> button

Displays the projector information.

(10) <AUTO SETUP> button

Automatically adjusts the image display position while projecting the image. [PROGRESS] is displayed on the screen while the image is adjusted automatically.

page 44)

(



(11) <SHUTTER> button

Use to temporarily turn off the image.(

(12) <ASPECT> button

Switches the aspect ratio of the image.(

(13) Lens (<FOCUS>, <ZOOM>, <SHIFT>) buttons

Adjusts the projection lens. (

(14) <FUNCTION> button

You can assign a frequently used operation as a shortcut button.(

(15) <DEFAULT> button

Resets the content of the sub-menu to the factory default.(

(16) <ID SET> button

Sets the ID number of the remote control to use for a system using multiple projectors.(

(17) <ID ALL> button

Use to simultaneously control all the projectors with one remote control for a system using multiple projectors.(



> button

page 24)

page 44)



pages 39, 41)



page 24)



page 43)



󱽃󱽄

page 46)



buttons

page 43)

page 45)

page 46)



Attention

zDo not drop the remote control. zAvoid contact with liquids or moisture. zDo not attempt to modify or disassemble the remote control.



page 44)



page 43)

Preparation

Note

zThe remote control can be used within a distance of about 30 m (98'5")

if pointed directly at the remote control receiver. The remote control can control at angles of up to ±15° vertically and ±30° horizontally, but the effective control range may be reduced.

zIf there are any obstacles between the remote control and the remote

control signal receiver, the remote control may not operate properly.

zThe signal will be reected off the screen. However, the operating range

may be limited from light reection loss due to the screen material.

zIf the remote control signal receiver directly receives strong light, such as

uorescent light, the remote control may not operate properly. Use it in a place distant from the light source.

zThe power indicator <ON (G)/STANDBY (R)> will ash if the projector

receives a remote control signal.

ENGLISH - 21

About your projector

(15)(16) (17)

(13) (14) (13)

(19)(13)

Projector body

Preparation

Front

■

(1) (2) (3) (4) (5)

(6) (7) (8) (6)

■Rear

(9) (10) (11) (12)

Side

■

Front

(1) Power indicator<ON (G)/STANDBY (R)>

Displays the status of the power.

(2) Lamp indicator <LAMP1>

Displays the status of lamp 1.

(3) Lamp indicator <LAMP2>

Displays the status of lamp 2.

(4) Temperature indicator <TEMP>

Displays the internal temperature status.

(5) Filter indicator <FILTER>

Displays the status of the air lter unit.

(6) Adjustable feet

Adjusts the projection angle.

(7) Remote control signal receiver (front)

(8) Projection lens

(for models with attached lenses only)

(9) Air exhaust port

(10) Lamp unit cover (

(11) Control panel (

(12) Remote control signal receiver (rear)

(13) Air intake port

(14) Connecting terminals (

(15) <MAIN POWER> switch

Turns on/off the main power.

(16) Security slot

This security slot is compatible with the Kensington security cables.

(17) <AC IN> terminal

Connect the supplied power cord.

(18) Air lter cover

The air lter unit is inside.

page 106)

(



(19) Burglar hook port

You can attach a commercial burglar prevention cable.



page 23)



page 109)

page 23)



)URQW

■Bottom

Front

(13)

22 - ENGLISH

Attention

zKeep your hands and other objects away from

the air exhaust port.

Keep your hands and face away.



Do not insert your ngers.

 



Keep heat-sensitive objects away.



Heated air from the air outlet port can cause bums, injury, or deformations.

Control panel

■

About your projector

(1)

(2)

(3)

(4)

(5) (6) (7) (8)

(1)

Power standby <

Sets the projector to the standby mode when the <MAIN POWER> switch on the projector is set to <ON>.

(2)

Power on <

Starts projection when the <MAIN POWER> switch on the projector is set to <ON> when the power is switched off (standby mode).

(3) <VIDEO> button

Switches to VIDEO input.

(4) <S-VIDEO> button

Switches to S-VIDEO input.

(5) <RGB1> button

Switches to RGB1 input.

(6) <RGB2> button

Switches to RGB2 input.

(7) <DVI-D> button

Switches to DVI-D input.

(8) <HDMI> button

Switches to HDMI input.

> button

(9)

(10)

(11)

(12)

(13)

(14)

(9) <MENU> button

Displays and erases the main menu. Returns to the previous screen when a sub-menu is displayed.( If you press the <MENU> button on the control panel for at least three seconds while the on-screen indication is off, the on-screen display is turned on.

(10) <LENS> button

Adjusts the focus, zoom, and shift (position) of the lens.

(11) <ENTER> button

Determines and executes an item in the menu screen.

(12) <SHUTTER> button

Use to temporarily turn off the image.(

(13)

󱽃󱽄

Use to select items in the menu screen, change settings, and adjust levels. It is also used to enter [SECURITY] passwords.

(14) <AUTO SETUP> button

Automatically adjusts the image display position while projecting the image. [PROGRESS] is displayed on the screen while the image is adjusted automatically.(

page 46)



selection buttons



page 44)

page 43)



Preparation

Connecting terminals

■

(1) (2) (3) (4) (5) (6)

(7) (8) (9) (10) (11)

(1) <LAN> terminal

This is a terminal to connect to the network. Used for control and monitoring. Image input through network connections is not possible.

(2) <VIDEO IN> terminal

This is a terminal to input video signals.

(3) <S-VIDEO IN> terminal

This is a terminal to input S video signals.

(4) <RGB 1 IN> (<R/P

<VD>) terminal

This is a terminal to input RGB signals or YC signals.

(5) <HDMI IN> terminal

This is a terminal to input HDMI signals.

(6) <DVI-D IN> terminal

This is a terminal to input DVI-D signals.

>, <G/Y>, <B/PB>, <SYNC/HD>,

BCR

/YPBPR

(7) <REMOTE 1 IN> terminal / <REMOTE 1 OUT> terminal

These are the terminals to connect the remote control for serial control when the system uses multiple projectors.

(8) <REMOTE 2 IN> terminal

This is a terminal to remotely control the projector using the external control circuit.

(9) <SERIAL IN> terminal

This is a RS-232C compatible terminal to externally control the projector by connecting a computer.

(10) <SERIAL OUT> terminal

This is a terminal to output the signal connected to the serial input terminal.

(11) <RGB 2 IN> terminal

This is a terminal to input RGB signals or YC signals.

BCR

/YPBPR

Attention

zWhen a LAN cable is directly connected to the projector, the network connection must be made indoors.

ENGLISH - 23

Using the remote control

Inserting and removing the batteries

1) Open the cover.

Preparation

2) Insert the batteries and close the cover

(ii)

(i)

(insert the

When removing the batteries, perform the steps



in reverse order.

side rst).

zThe ID number set on the remote control will

be stored unless it is set again. However, it will be erased if the remote control is left with dead batteries. Set the same ID number again when the batteries are replaced.

Note

zSet the ID number of the projector from the

[PROJECTOR SETUP] menu → “[PROJECTOR ID]” (

page 68).



Connecting to the projector with a cable

When you use the system with multiple projectors, congure the units as in the following gure. Use a commercial M3 stereo mini jack cable and connect the other devices to the <REMOTE 1 IN>/<REMOTE 1 OUT> terminals of the projector. The remote control is effective even in places where an obstacle stands in the light path or where devices are susceptible to outside light.

Connecting terminals

Setting Remote control ID numbers

When you use the system with multiple projectors, you can operate all the projectors simultaneously or each projector individually using single remote control, if a unique ID number is assigned to each projector. After setting the ID number of the projector, set same ID number on the remote control.

The factory default ID number of the projector is set to [ALL]. When using a single projector, press the <ID ALL> button on the remote control. Also, you can control a projector if you press the <ID ALL> button on the remote control even if you do not know the projector ID.

How to set

■

1) Press the <ID SET> button on the remote control.

2) Within ve seconds, press the twodigit ID number set on the projector using the number (<0> - <9>) buttons.

If you press the <ID ALL> button, you can



operate the projectors regardless of the setting of the projector’s ID number.

Attention

zSince the ID number of the remote control can be

also set without the projector, do not press the <ID SET> button carelessly. If the <ID SET> button is pressed and no number (<0> - <9>) buttons are pressed within the next ve seconds, the ID number returns to its original value before the <ID SET> button was pressed.

Connect to the second projector

M3 stereo mini jack cable (commercially available)

Remote control

Connect to remote control wired terminal

Attention

zUse a cable that is 15 m (49'2") or shorter, with 2

core shield. The remote control may not operate when the length of the cable exceeds 15 m (49'2") or when the shielding of the cable is inadequate.

24 - ENGLISH

Setting up

Projection method

You can use the projector with any of the following four projection methods. Select the appropriate method depending on the environment.

Mounting on the ceiling and

■

projecting forward

Menu item

[PROJECTION

METHOD]

[COOLING

CONDITION]

Mounting on the ceiling and

■

Method

[FRONT/CEILING]

[CEILING SETTING]

projecting from rear

(Using the translucent screen)

Setting on a desk/oor and

■

projecting from rear

(Using the translucent screen)

Menu item

[PROJECTION

METHOD]

[COOLING

CONDITION]

Setting on a desk/oor and

■

Method

[REAR/FLOOR]

[FLOOR SETTING]

projecting forward

Getting Started

Menu item

[PROJECTION

METHOD]

[COOLING

CONDITION]

*1: For menu item details, see the [PROJECTOR SETUP] menu → [PROJECTION METHOD] ( page 68) and [COOLING

CONDITION] (

page 69).



Method

[REAR/CEILING]

[CEILING SETTING]

Menu item

[PROJECTION

METHOD]

[COOLING

CONDITION]

Method

[FRONT/FLOOR]

[FLOOR SETTING]

Parts for ceiling mount (optional)

You can install the projector on the ceiling using the optional ceiling mount bracket (ET-PKD56H: for high ceilings, or ET-PKD55S: for low ceilings).

zUse only the ceiling mount brackets specied for this projector. zRefer to the installation manual for the ceiling mount bracket when installing the bracket and the projector.

Attention

zTo ensure projector performance and security, installation of the ceiling mount bracket must be carried out by

your dealer or a qualied technician.

ENGLISH - 25

Setting up

Projection screen

Screen size and throw distance

Refer to the following gures and table describing projection distances to install the projector. Image size and image position can be adjusted in accordance with the screen size and screen position.

Getting Started

Screen

L（LW/LT）

SW SH

Screen

L (LW/LT)

*1: LW: Minimum projection distance when the zoom lens is used

LT: Maximum projection distance when the zoom lens is used

Projection distance (m)

SH Image height (m)

SW Image width (m)

SD Image diagonal size (m)

Distance (m) from the lens center to the bottom edge of the image

Attention

zBefore setting up, read “Precautions for use”( zDo not use the projector and the high-powered laser equipment in the same room.

Hitting of a laser beam on to the lens can damage the DLP chips.

pages 14 to 19).



26 - ENGLISH

Setting up

Projection distance per projection lens

■

When the screen aspect is 16:10 (unit: m)



(The dimensions of the following table contain slight error.)

Lens type

Projection lens Model No. ― ET-DLE055 ET-DLE080 ET-DLE150 ET-DLE250

Throw ratio

Projection screen size Projection distance (L)

Screen

diagonal

(SD)

1.27 (50")

1.52 (60")

1.78 (70")

2.03 (80")

2.29 (90")

2.54 (100")

3.05 (120")

3.81 (150")

5.08 (200")

6.35 (250")

7.62 (300")

8.89 (350")

10.16 (400")

12.70 (500")

15.24 (600")

Height

(SH)

0.673 1.077 1.82 2.52 0.83 0.82 1.04 1.38 2.01 2.42 3.87

0.808 1.292 2.20 3.04 1.00 1.00 1.25 1.66 2.43 2.92 4.65

0.942 1.508 2.58 3.56 1.18 1.17 1.47 1.95 2.84 3.42 5.44

1.077 1.723 2.95 4.08 1.35 1.35 1.68 2.23 3.25 3.92 6.23

1.212 1.939 3.33 4.60 1.53 1.52 1.90 2.52 3.66 4.42 7.02

1.346 2.154 3.71 5.11 1.70 1.70 2.11 2.81 4.08 4.92 7.81

1.615 2.585 4.47 6.15 2.05 2.05 2.55 3.38 4.90 5.91 9.39

2.019 3.231 5.60 7.71 2.58 2.57 3.19 4.24 6.14 7.41 11.75

2.692 4.308 7.50 10.30 3.45 3.44 4.27 5.67 8.20 9.91 15.70

3.365 5.385 9.39 12.89 ― 4.31 5.35 7.10 10.26 12.41 19.64

4.039 6.462 11.28 15.49 ― 5.18 6.43 8.53 12.33 14.91 23.59

4.712 7.539 13.18 18.08 ― 6.06 7.51 9.96 14.39 17.40 27.53

5.385 8.616 15.07 20.67 ― 6.93 8.59 11.39 16.45 19.90 31.48

6.731 10.770 18.86 25.86 ― 8.67 10.75 14.25 20.58 24.90 39.37

8.077 12.923 22.64 31.05 ― 10.42 12.91 17.11 24.70 29.89 47.25

1.7 – 2.4:1 0.8:1 0.8 – 1.0:1 1.3 – 1.9:1 2.3 – 3.6:1

Width

(SW)

Standard

Zoom lens

Min. Max. Fixed Min. Max. Min. Max. Min. Max.

Fixed-focus

Lens

Ultra-short focus

Zoom lens

Optional lens

Short focus

Zoom lens

Medium focus

Zoom lens

Getting Started

Optional lens

Lens type

Projection lens Model No. ET-DLE350 ET-DLE450

Throw ratio

Projection screen size Projection distance (L)

Screen

diagonal

(SD)

1.27 (50")

1.52 (60")

1.78 (70")

2.03 (80")

2.29 (90")

2.54 (100")

3.05 (120")

3.81 (150")

5.08 (200")

6.35 (250")

7.62 (300")

8.89 (350")

10.16 (400")

12.70 (500")

15.24 (600")

*1: The throw ratio is based on the value during projection onto a 2.03 m (80") screen size. *2: The height position (H) is SH/2 because lens shift cannot be used when a xed-focus lens (ET-DLE055) is attached.

Height

(SH)

0.673 1.077 3.80 5.81 5.66 9.12 0 - 0.34 0.34

0.808 1.292 4.59 7.00 6.85 11.01 0 - 0.40 0.40

0.942 1.508 5.38 8.19 8.04 12.89 0 - 0.47 0.47

1.077 1.723 6.16 9.38 9.23 14.78 0 - 0.54 0.54

1.212 1.939 6.95 10.57 10.43 16.66 0 - 0.61 0.61

1.346 2.154 7.74 11.76 11.62 18.55 0 - 0.67 0.67

1.615 2.585 9.31 14.14 14.00 22.31 0 - 0.81 0.81

2.019 3.231 11.68 17.71 17.58 27.97 0 - 1.01 1.01

2.692 4.308 15.61 23.66 23.54 37.39 0 - 1.35 1.35

3.365 5.385 19.55 29.61 29.50 46.81 0 - 1.68 ―

4.039 6.462 23.49 35.56 35.46 56.24 0 - 2.02 ―

4.712 7.539 27.42 41.51 41.42 65.66 0 - 2.36 ―

5.385 8.616 31.36 47.46 47.38 75.08 0 - 2.69 ―

6.731 10.770 39.23 59.36 59.30 93.93 0 - 3.37 ―

8.077 12.923 47.11 71.25 71.22 112.77 0 - 4.04 ―

3.6 – 5.4:1 5.4 – 8.6:1

Width

(SW)

Long focus

Zoom lens

Min. Max. Min. Max.

Ultra-long focus

Zoom lens

Standard zoom

lens/ ET-DLE080/

Height position

ET-DLE150/ ET-DLE250/ ET-DLE350/

ET-DLE450

(H)

ET-DLE055

(Fixed)

ENGLISH - 27

Setting up

When the screen aspect is 16:9 (unit: m)



(The dimensions of the following table contain slight error.)

Projection lens Model No. ― ET-DLE055 ET-DLE080 ET-DLE150 ET-DLE250

Projection screen size Projection distance (L)

Screen

diagonal

(SD)

1.27 (50")

1.52 (60")

1.78 (70")

2.03 (80")

2.29 (90")

Getting Started

2.54 (100")

3.05 (120")

3.81 (150")

5.08 (200")

6.35 (250")

7.62 (300")

8.89 (350")

10.16 (400")

12.70 (500")

15.24 (600")

Lens type

Throw ratio

Height

(SH)

0.623 1.107 1.87 2.64 0.85 0.85 1.07 1.42 2.07 2.49 3.97

0.747 1.328 2.26 3.19 1.03 1.03 1.29 1.71 2.49 3.00 4.79

0.872 1.550 2.65 3.73 1.21 1.21 1.51 2.00 2.92 3.51 5.60

0.996 1.771 3.04 4.27 1.39 1.39 1.73 2.30 3.34 4.03 6.41

1.121 1.992 3.43 4.82 1.57 1.57 1.95 2.59 3.77 4.54 7.22

1.245 2.214 3.82 5.36 1.75 1.75 2.17 2.89 4.19 5.05 8.03

1.494 2.657 4.60 6.45 2.11 2.10 2.62 3.47 5.04 6.08 9.65

1.868 3.321 5.76 8.08 2.65 2.64 3.28 4.36 6.31 7.62 12.08

2.491 4.428 7.71 10.80 3.55 3.54 4.39 5.82 8.43 10.19 16.14

3.113 5.535 9.65 13.51 ― 4.43 5.50 7.29 10.55 12.75 20.19

3.736 6.641 11.60 16.23 ― 5.33 6.61 8.76 12.67 15.32 24.25

4.358 7.748 13.55 18.95 ― 6.23 7.72 10.23 14.79 17.89 28.30

4.981 8.855 15.49 21.66 ― 7.12 8.83 11.70 16.91 20.46 32.35

6.226 11.069 19.38 27.10 ― 8.91 11.05 14.64 21.15 25.59 40.46

7.472 13.283 23.27 32.53 ― 10.71 13.27 17.58 25.39 30.72 48.57

1.7 – 2.4:1 0.8:1 0.8 – 1.0:1 1.3 – 1.9:1 2.3 – 3.6:1

Width (SW)

Standard

Zoom lens

Min. Max. Fixed Min. Max. Min. Max. Min. Max.

Fixed-focus

Lens

Ultra-short focus

Zoom lens

Optional lens

Short focus

Zoom lens

Medium focus

Zoom lens

Optional lens

Lens type

Projection lens Model No. ET-DLE350 ET-DLE450

Throw ratio

Projection screen size Projection distance (L)

Screen

diagonal

(SD)

1.27 (50")

1.52 (60")

1.78 (70")

2.03 (80")

2.29 (90")

2.54 (100")

3.05 (120")

3.81 (150")

5.08 (200")

6.35 (250")

7.62 (300")

8.89 (350")

10.16 (400")

12.70 (500")

15.24 (600")

Height

(SH)

0.623 1.107 3.91 5.98 5.82 9.39 –0.06 - 0.31 0.31

0.747 1.328 4.72 7.20 7.05 11.32 –0.07 - 0.37 0.37

0.872 1.550 5.53 8.43 8.27 13.26 –0.09 - 0.44 0.44

0.996 1.771 6.34 9.65 9.50 15.20 –0.10 - 0.50 0.50

1.121 1.992 7.15 10.87 10.72 17.13 –0.11 - 0.56 0.56

1.245 2.214 7.96 12.09 11.95 19.07 –0.12 - 0.62 0.62

1.494 2.657 9.58 14.54 14.40 22.94 –0.15 - 0.75 0.75

1.868 3.321 12.00 18.21 18.08 28.75 –0.19 - 0.93 0.93

2.491 4.428 16.05 24.32 24.20 38.44 –0.25 - 1.25 1.25

3.113 5.535 20.10 30.44 30.33 48.12 –0.31 - 1.56 ―

3.736 6.641 24.14 36.55 36.45 57.81 –0.37 - 1.87 ―

4.358 7.748 28.19 42.67 42.58 67.49 –0.44 - 2.18 ―

4.981 8.855 32.24 48.78 48.71 77.18 –0.50 - 2.49 ―

6.226 11.069 40.33 61.01 60.96 96.55 –0.62 - 3.11 ―

7.472 13.283 48.42 73.24 73.21 115.91 –0.75 - 3.74 ―

3.6 – 5.4:1 5.4 – 8.6:1

Width (SW)

Long focus

Zoom lens

Min. Max. Min. Max.

Ultra-long focus

Zoom lens

Standard zoom

lens/ ET-DLE080/

Height position

ET-DLE150/ ET-DLE250/ ET-DLE350/ ET-DLE450

(H)

ET-DLE055

(Fixed)

28 - ENGLISH

Setting up

When the screen aspect is 4:3 (unit: m)



(The dimensions of the following table contain slight error.)

Lens type

Projection lens Model No. ― ET-DLE055 ET-DLE080 ET-DLE150 ET-DLE250

Throw ratio

Projection screen size Projection distance (L)

Screen

diagonal

(SD)

1.27 (50")

1.52 (60")

1.78 (70")

2.03 (80")

2.29 (90")

2.54 (100")

3.05 (120")

3.81 (150")

5.08 (200")

6.35 (250")

7.62 (300")

8.89 (350")

10.16 (400")

12.70 (500")

15.24 (600")

Height

(SH)

0.762 1.016 2.07 2.92 0.94 0.94 1.18 1.56 2.29 2.75 4.39

0.914 1.219 2.50 3.52 1.14 1.14 1.42 1.89 2.75 3.31 5.28

1.067 1.422 2.93 4.12 1.34 1.33 1.67 2.21 3.22 3.88 6.17

1.219 1.626 3.35 4.72 1.54 1.53 1.91 2.54 3.69 4.44 7.07

1.372 1.829 3.78 5.31 1.74 1.73 2.16 2.86 4.15 5.01 7.96

1.524 2.032 4.21 5.91 1.93 1.93 2.40 3.18 4.62 5.57 8.85

1.829 2.438 5.07 7.11 2.33 2.32 2.89 3.83 5.55 6.71 10.64

2.286 3.048 6.35 8.91 2.93 2.91 3.62 4.80 6.96 8.40 13.32

3.048 4.064 8.50 11.90 3.92 3.90 4.84 6.42 9.29 11.23 17.78

3.810 5.080 10.64 14.89 ― 4.89 6.07 8.04 11.63 14.06 22.25

4.572 6.096 12.78 17.88 ― 5.88 7.29 9.66 13.96 16.88 26.71

5.334 7.112 14.93 20.88 ― 6.86 8.51 11.28 16.30 19.71 31.18

6.096 8.128 17.07 23.87 ― 7.85 9.73 12.90 18.63 22.54 35.64

7.620 10.160 21.36 29.85 ― 9.82 12.17 16.13 23.30 28.19 44.58

9.144 12.192 25.64 35.84 ― 11.80 14.62 19.37 27.97 33.85 53.51

2.1 – 2.9:1 0.9:1 0.9 – 1.2:1 1.6 – 2.3:1 2.7 – 4.3:1

Width

(SW)

Standard

Zoom lens

Min. Max. Fixed Min. Max. Min. Max. Min. Max.

Fixed-focus

Lens

Ultra-short focus

Zoom lens

Optional lens

Short focus

Zoom lens

Medium focus

Zoom lens

Getting Started

Optional lens

Lens type

Projection lens Model No. ET-DLE350 ET-DLE450

Throw ratio

Projection screen size Projection distance (L)

Screen

diagonal

(SD)

1.27 (50")

1.52 (60")

1.78 (70")

2.03 (80")

2.29 (90")

2.54 (100")

3.05 (120")

3.81 (150")

5.08 (200")

6.35 (250")

7.62 (300")

8.89 (350")

10.16 (400")

12.70 (500")

15.24 (600")

Height

(SH)

0.762 1.016 4.32 6.60 6.45 10.37 0 - 0.38 0.38

0.914 1.219 5.21 7.95 7.80 12.50 0 - 0.46 0.46

1.067 1.422 6.10 9.29 9.14 14.63 0 - 0.53 0.53

1.219 1.626 7.00 10.64 10.49 16.77 0 - 0.61 0.61

1.372 1.829 7.89 11.99 11.84 18.90 0 - 0.69 0.69

1.524 2.032 8.78 13.34 13.19 21.03 0 - 0.76 0.76

1.829 2.438 10.56 16.03 15.89 25.30 0 - 0.91 0.91

2.286 3.048 13.24 20.07 19.94 31.70 0 - 1.14 1.14

3.048 4.064 17.69 26.80 26.69 42.37 0 - 1.52 1.52

3.810 5.080 22.15 33.54 33.44 53.04 0 - 1.91 ―

4.572 6.096 26.61 40.27 40.18 63.70 0 - 2.29 ―

5.334 7.112 31.06 47.01 46.93 74.37 0 - 2.67 ―

6.096 8.128 35.52 53.74 53.68 85.04 0 - 3.05 ―

7.620 10.160 44.43 67.21 67.17 106.37 0 - 3.81 ―

9.144 12.192 53.35 80.68 80.67 127.70 0 - 4.57 ―

4.3 – 6.5:1 6.5 – 10.3:1

Width

(SW)

Long focus

Zoom lens

Min. Max. Min. Max.

Ultra-long focus

Zoom lens

Standard zoom

lens/ ET-DLE080/

Height position

ET-DLE150/ ET-DLE250/ ET-DLE350/

ET-DLE450

(H)

ET-DLE055

(Fixed)

ENGLISH - 29

Setting up

Projection distance formulas by projection lens

■

To use a screen size not listed in this manual, check the screen size SD and use the following formula to calculate projection distance. The unit of the calculation result is m.

Standard zoom lens ―

Fixed-focus lens Model No.: ET-DLE055

Getting Started

Ultra-short focus zoom lens Model No.: ET-DLE080

Short focus zoom lens Model No.: ET-DLE150

Medium focus zoom lens Model No.: ET-DLE250

Long focus zoom lens Model No.: ET-DLE350

Ultra-long focus zoom lens Model No.: ET-DLE450

Lens type Aspect ratio Projection distance (L) formula

16:10

16:9

4:3

16:10 ― L = 0.6890 x SD (m) – 0.0476

16:9 ― L = 0.7087 x SD (m) – 0.0476

4:3 ― L = 0.7795 x SD (m) – 0.0476