Panasonic PT-DZ13K Technical data

PEC

ILE

Product Number :

Product Name :

PT-DZ13K

3-Chip DLP™Projector

As of April 2013. Specifications and appearance are subject to change without notice.

SFD12M020

1/19

S PEC F ILE

3-Chip DLP™Projector

Specifications

Main unit

Power supply

Power consumption

DLP™ chip Panel size

Lens

Lamp

Screen size

Brightness*

Center-to-corner uniformity*

Contrast*

Resolution

Scanning frequency SDI

120 V AC, 50/60 Hz

220–240 V AC, 50/60 Hz

Display method

Pixels

HDMI/DVI-D/RGB

(YCBCR)

BPR

Video/S-Video

PT-DZ13K

120 V AC, 9.3 A, 50/60 Hz

220–240 V AC, 5 A, 50/60 Hz

1,000 W (1,030 VA) (0.2 W with standby mode set to eco.*

standby mode set to normal. Both with fan stopped.)

970 W (1,020 VA) (0.3 W with standby mode set to eco.*1 9 W with

standby mode set to normal. Both with fan stopped.)

24.4 mm (0.96 inches) diagonal (16:10 aspect ratio)

DLP™ chip × 3 (R, G, B), DLP™ projection system

2,304,000 (1,920 × 1,200) × 3, total of 6,912,000 pixels

Optional powered zoom/focus lenses

380 W UHM lamps (× 2) (dual lamp, high mode)

1.78–25.4 m (70–1,000 inches) (1.78–15.24 m (70–600 inches) with the

ET-D75LE8), 16:10 aspect ratio

12,000 lumens (dual lamp, high mode)

90%

10,000:1 (full on/full off, in dynamic iris 3 mode)

1,920 × 1,200 pixels (Input signals that exceed this resolution will be

converted to 1,920 × 1,200 pixels.)

Dual-link HD-SDI signal (RGB 4:4:4 12-bit/10-bit):

SMPTE ST 372 compliant: 1125(1080)/60i, 1125(1080)/50i,

1125(1080)/25p, 1125(1080)/24p, 1125(1080)/24sF, 1125(1080)/30p

Dual-link HD-SDI signal (X

Y Z 4:4:4 12-bit):

SMPTE ST 372 compliant: 2048 × 1080/24p, 2048 × 1080/24sF,

3G-SDI signal (RGB 4:4:4 12-bit/10-bit):

SMPTE ST 424 compliant: 1125(1080)/60i, 1125(1080)/50i,

1125(1080)/25p, 1125(1080)/24p, 1125(1080)/24sF, 1125(1080)/30p

3G-SDI signal (YPBPR4:2:2 10-bit):

SMPTE ST 424 compliant: 1125(1080)/60p, 1125(1080)/50p

HD-SDI signal (YP

4:2:2 10-bit):

BPR

SMPTE ST 292 compliant: 750(720)/60p, 750(720)/50p, 1125(1035)/60i,

1125(1080)/60i, 1125(1080)/50i, 1125(1080)/25p, 1125(1080)/24p,

1125(1080)/24sF, 1125(1080)/30p

SD-SDI signal (YC

4:2:2 10-bit):

BCR

SMPTE ST 259 compliant: 525i(480i), 625i(576i)

Horizontal: 15 kHz–100 kHz, vertical: 24 Hz – 120 Hz,

dot clock: 25–162 MHz or lower (HDMI/DVI: 25 MHz – 162 MHz)

525i (480i): fH15.75 kHz; fV60 Hz,

625i (576i): f

525p (480p): f

625p (576p): f

750 (720)/60p: f

750 (720)/50p: f

1125 (1035)/60i: f

1125 (1080)/60i: f

1125 (1080)/50i: f

1125 (1080)/25p: f

1125 (1080)/24p: f

1125 (1080)/24sF: f

1125 (1080)/30p: f

1125 (1080)/60p: f

1125 (1080)/50p: f

H: 15.75 kHz, fV: 60 Hz [NTSC/NTSC4.43/PAL-M/PAL60]

15.63 kHz; fV50 Hz,

31.50 kHz; fV60 Hz,

31.25 kHz; fV50 Hz,

45.00 kHz; fV60 Hz,

37.50 kHz; fV50 Hz,

33.75 kHz; fV60 Hz,

28.13 kHz; fV50 Hz,

28.13 kHz; fV25 Hz,

27.00 kHz; fV24 Hz,

27.00 kHz; fV48 Hz,

33.75 kHz; fV30 Hz,

67.50 kHz; fV60 Hz,

56.25 kHz; fV50 Hz

fH: 15.63 kHz, fV: 50 Hz [PAL/PAL-N/SECAM]

6 W with

As of April 2013

SFD12M020

2/19

S PEC F ILE

3-Chip DLP™Projector

Optical axis shift Vertical

Horizontal

Keystone correction range

Installation

Terminals SDI IN 1

SDI IN 2

HDMI IN

DVI-D IN

RGB 1 IN

R, G, B

Y, P

S-Video signal

RGB 2 IN

R, G, B

Y, P

B, PR (Y, CB, CR)

, PR(Y, CB, CR)

PT-DZ13K

±55% (±44% with the ET-D75LE6) from center of screen, powered

±20% (±15% with the ET-D75LE6) from center of screen, powered

NOTE: Optical axis shift function cannot be operated when used with the ET-D75LE50.

Vertical ±40°, horizontal ±15°

(vertical ±22° and horizontal ±15° with the ET-D75LE5/LE50,

vertical ±28° and horizontal ±15° with the ET-D75LE6) When using only the KEYSTONE correction of the Geometric Adjustment

function: Vertical ±40°, horizontal ±15°

When using the optional upgrade kit ET-UK20*

Vertical ±40° and horizontal ±40° with the ET-D75LE1/LE2/LE10/LE20,

vertical ±45°and horizontal ±40° with the ET-D75LE3/LE4/LE30/LE40,

vertical ±22° and horizontal ±15° with the ET-D75LE5/LE50,

vertical ±28° and horizontal ±15° with the ET-D75LE6 When using both the KEYSTONE and CURVED corrections of the Geometric

Adjustment function: Vertical ±20°, horizontal ±15°

(vertical ±8° and horizontal ±8° with the ET-D75LE5/50,

vertical ±10° and horizontal ±10° with the ET-D75LE6)

Ceiling/floor, front/rear

BNC × 1,

Dual-link HD-SDI signal: SMPTE ST 372 compliant (Link-A)

3G-SDI signal: SMPTE ST 424 compliant

HD-SDI signal: SMPTE ST 292 compliant

SD-SDI signal: SMPTE ST 259 compliant

BNC × 1,

Dual-link HD-SDI signal: SMPTE ST 372 compliant (Link-B)

HD-SDI signal: SMPTE ST 292 compliant

SD-SDI signal: SMPTE ST 259 compliant

HDMI 19-pin × 1, Deep Color, compatible with HDCP,

525i(480i)*4, 625i(576i)*4, 525p(480p), 625p(576p), 750(720)/60p,

750(720)50p, 1125(1080)/60i, 1125(1080)/50i, 1125(1080)/25p,

1125(1080)/24p, 1125(1080)/24sF, 1125(1080)/30p, 1125(1080)/60p,

1125(1080)/50p

VGA (640 × 480) – WUXGA*

(1,920 × 1,200),

dot clock: 25 MHz –162 MHz

NOTE: Compatible with non-interlaced signals only.

DVI-D 24-pin × 1, DVI 1.0 compliant, HDCP compatible,

for single link only

525i(480i)*

, 625i(576i)*4, 525p(480p), 625p(576p), 750(720)/60p,

750(720)50p, 1125(1080)/60i, 1125(1080)/50i, 1125(1080)/25p,

1125(1080)/24p, 1125(1080)/24sF, 1125(1080)/30p, 1125(1080)/60p,

1125(1080)/50p

VGA (640 × 480) – WUXGA*

(1,920 × 1,200),

dot clock: 25 MHz –162 MHz

NOTE: Compatible with non-interlaced signals only.

BNC × 5

R: 0.7 Vp-p, 75 ohms,

G: 0.7 Vp-p (G: 1.0 Vp-p for sync on G), 75 ohms,

B: 0.7 Vp-p, 75 ohms

HD, VD/SYNC: TTL, high impedance, positive/negative automatic

NOTE: SYNC/HD and VD terminals do not accept tri-level sync signals.

Y: 1.0 Vp-p (including sync signal), PB/PR (CB /CR): 0.7 Vp-p, 75 ohms

Y: 1.0 Vp-p, C: 0.286 Vp-p, 75 ohms

D-sub HD 15-pin (female) × 1

R: 0.7 Vp-p, 75 ohms,

G: 0.7 Vp-p (G: 1.0 Vp-p for sync on G), 75 ohms,

B: 0.7 Vp-p, 75 ohms

HD, VD/SYNC: TTL, high impedance, positive/negative automatic

NOTE: SYNC/HD and VD terminals do not accept tri-level sync signals.

Y: 1.0 Vp-p (including sync signal), PB/PR(CB/CR): 0.7 Vp-p, 75 ohms

As of April 2013

SFD12M020

3/19

S PEC F ILE

3-Chip DLP™Projector

VIDEO IN

3D SYNC 1 IN/OUT

3D SYNC 2 OUT

SERIAL IN

SERIAL OUT

REMOTE 1 IN

REMOTE 1 OUT

REMOTE 2 IN

LAN

Power cord length

Cabinet materials

Dimensions (W ×H × D):

Weight*

Operation noise*

Operating temperature

Operating humidity

Remote control unit

Power supply

Operation range*

Dimensions (W × H × D)

Weight

PT-DZ13K

BNC × 1, 1.0 Vp-p, 75 ohms

Input: TTL, high impedance. Output: TTL, max. 10 mA

BNC × 1, 1.0 Vp-p, 75 ohms, TTL, max. 10 mA

D-sub 9-pin (female) ×1 for external control (RS-232C compliant)

D-sub 9-pin (male) ×1 for link control

M3 jack ×1 for wired remote control

M3 jack ×1 for link control

D-sub 9-pin ×1 for external control (parallel)

RJ-45 ×1 for network connection, 100Base-TX/10Base-T, compliant

with PJLink™ (class 1)

3.0 m (9 10 in)

Molded plastic

530 × 200*

(20-7/8 × 7-7/8*

× 548.5 mm

× 21-19/32 inches) (without lens)

24 kg (52.9 lbs) (without lens)

45 dB (high mode), 43 dB (middle mode), 37 dB (eco mode)

0°– 45°C (32°–113°F) *

10%–80% (no condensation)

3 V DC (AA/R6 type battery × 2)

Approx. 30 m (98

5 in) when operated from directly in front of the

signal receptor

51 × 176 × 28 mm (2 × 6-15/16 × 1-3/32 inches)

Approx. 134 g (4.7 oz) (including batteries)

(RS-232C compliant)

Supplied accessories

Power cord (×1) (x2 for PT-DZ13KE)

Wireless/wired remote control unit (× 1)

Batteries for remote control (AA/R6 type × 2)

Lens drop-prevention screw (× 1)

Softwar

e CD-ROM (Logo Transfer Software, Multi Projector Monitoring

& Control Software) (× 1)

Optional accessories

Zoom lens (0.9–1.1:1)

Zoom lens (1.3–1.7:1)

Zoom lens (1.7– 2.4:1)

Zoom lens (2.4–4.7:1)

Zoom lens (4.6–7.4:1)

Zoom lens (7.3–13.8:1)

Fixed-focus lens (0.7:1)

Lens motor cover

Ceiling mount bracket

ET-D75LE6

ET-D75LE10

ET-D75LE20

ET-D75LE30

ET-D75LE40

ET-D75LE8

ET-D75LE50

ET-D75MC1

ET-PKD310H (for high ceilings)

ET-PKD310S (for low ceilings)

Attachment for ceiling mount bracket ET-PAD310

Frame

Smoke cut filter

-PFD310

-SFD320

Replacement smoke cut filter ET-SFR320

Upgrade kit

Replacement lamp unit

ET-UK20

ET-LAD310A (one bulb)

ET-LAD310AW (a set of two bulbs)

Replacement lamp unit for portrait mode

ET-LAD320P (one bulb)

ET-LAD320PW (a set of two bulbs)

Replacement filter unit

ET-EMF320

Weights and dimensions shown are approximate. Specifications a nd appearance are subject to change without notice.

1 When the standby mode is set to eco, network functions such as power on over the LAN network will not operate, and the serial output termi-

nal cannot be used. Also, only certain commands can be received for e xternal control using the serial terminal.

As of April 2013

SFD12M020

4/19

S PEC F ILE

3-Chip DLP™Projector

2 Measurement, measuring conditions, and method of notation all comply with ISO 21118 international standards.

3 Up to a total of ±55° during simultaneous horizontal and vertical correction.

4 Only compatible with dot clock frequency of 27 MHz (pixel repetition signal)

5 WUXGA resolution is supported only when the signals are compliant with VESA CVT- RB (Coordinated Video Timing-Reduced Blanking).

6 With legs at shortest position.

7Average value (excluding the optional lens). May differ depending on models.

* *8 The operating temperature range is 0 °C to 40 °C (32 °F to 104 °F) when the FAN CONTROL is set to HIGH ALTITUDE MODE (for altitudes from

1,400 m to 2,700 m (4,593 ft to 8,858 ft) above sea level). When the projector is used with the ET-SFD320 Smoke Cut Filter, the operating temperature range is 0 °C to 35 °C (32 °F to 95 °F), and the projector cannot be used in places at high altitude. The operating temperature range is 0 °C to 40 °C (32 °F to 104 °F) when the ET-LAD320P/LAD320PW lamp is mounted and the projector is used in portrait configuration. The operating temperature range is 0 °C to 35 °C (32 °F to 95 °F) when the FAN CONTROL is set to HIGH ALTITUDE MODE (for altitudes from 1,400 m to 2,700 m (4,593 ft to 8,858 ft) above sea level). When the projector is used with the ET-SFD320 Smoke Cut Filter, the operating temperature range is 0 °C to 30 °C (32 °F to 86 °F).

*9 Operation range differs depending on environments.

PT-DZ13K

Dimensions

540 (21-1/4)

548.5 (21-19/32)

Terminals

8.5

(11/32)

462 (18-3/16)

530 (20-7/8)

100

200 (7-7/8)

(3-15/16)

(1-1/32)

unit : mm (inch) NOTE: This illustration is not drawn to scale.

468 (18-7/16)

1 Remote 1 input

2 Remote 1 output

3 Remote 2 input

4Serial i nput

5Serial output

6SDI 1 input

7SDI 2 input

8HDMI i nput

9 RGB 1 input

10 RGB 2 Input

11 DVI-D i nput

12 Video input

13 3D sync 1 input/output

14 3D sync 2 output

15 LAN connector

As of April 2013

SFD12M020

5/19

S PEC F ILE

3-Chip DLP™Projector

Standard setting-up position

Upper edge of projected image

Projected image

H H

Lower edge of projected image

Projected image

*1198

(7-25/32)

100

(3-15/16)

φ60.5

(12-3/8)

342

(13-15/32)

100 (3-15/16)

340～420

(13-3/8–

100

(3-15/16)

100

(3-15/16)

–

(17-5/32

16-17/32)

436～516

PT-DZ13K

*1 When the lens protrudes to the

maximum. 212 mm (8-11/32) w ith the ET-D75LE6

125 mm (4-29/32) w ith the ET-D75LE10

20-5/16)

121 mm (4-3/4) w ith the ET-D75LE20 121 mm (4-3/4) w ith the ET-D75LE30 124 mm (4-7/8) w ith the ET-D75LE40 254 mm (10) w ith the ET-D75LE8 203 mm (8) w ith the ET-D75LE50

*2 Adjustable in 40 mm (1-9/16) steps.

NOTE:

Illustrations show the projector installed using optional ceiling mount bracket ET-PKD310H and an optional lens.

This illustration is not drawn to scale.

unit : mm (inch)

Caution:

• All construction work should be done by a qualified technician.

• When mounting to the ceiling, use the special mounting bracket.

Furthermore, in order to prevent it from falling down from the ceiling, use the supplied wire on the mounting bracket.

As of April 2013

SFD12M020

6/19

+ 13 hidden pages