Panasonic PT-DX810US Operating Instruction

Operating Instructions

Functional Manual

DLPTM Projector Commercial Use

Model No. PT-DW740U

PT-DW740UL

PT-DX810U

PT-DX810UL

Thank you for purchasing this Panasonic product.

This manual is common to all the models regardless of sufixes of the Model No.

z S: Silver model, the standard zoom lens supplied K: Black model, the standard zoom lens supplied

LS: Silver model, the lens sold separately LK: Black model, the lens sold separately

Before operating this product, please read the instructions carefully and save this manual for future use.

Before using your projector, be sure to read “Read this irst!” (X pages 2 to 8).

ENGLISH

TQBJ0445

Read this irst!

Read this irst!

WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DONOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.

The lightning lash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of suficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the

product.

CAUTION: This equipment is equipped with a three-pin grounding-type power plug. Do not remove the grounding pin on the power plug. This plug will only it a grounding-type power outlet. This is a safety feature. If

you are unable to insert the plug into the outlet, contact an electrician.
Do not defeat the purpose of the grounding plug.	Do not remove

CAUTION: To assure continued compliance, follow the attached installation instructions, which include using the provided power cord and shielded interface cables when connecting to computer or peripheral device. If you use serial port to connect PC for external control of projector, you must use a commercial RS-232C serial interface cable with ferrite core. Any unauthorized changes or modiications to this equipment will void the user’s authority to operate.

2 - ENGLISH

Be sure to read “Read this irst!”

Read this irst!

FCC NOTICE (USA)

Veriication
Model Number:	PT-DW740US / PT-DW740UK / PT-DW740ULS / PT-DW740ULK /
	PT-DX810US / PT-DX810UK / PT-DX810ULS / PT-DX810ULK
Trade Name:	Panasonic
Responsible Party:	Panasonic Corporation of North America
Address:	One Panasonic Way, Secaucus, NJ 07094
Telephone number:	[phone]

E-mail: [e-mail]

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any interference received,

including interference that may cause undesired operation.

To assure continued compliance, follow the attached installation instructions and do not make any unauthorized modiications.

CAUTION:

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

NOTIFICATION (Canada)

This class A digital apparatus complies with Canadian ICES-003.

WARNING:

zNot for use in a computer room as deined in the Standard for the Protection of Electronic Computer/Data Processing Equipment, ANSI/NFPA 75.

zFor permanently connected equipment, a readily accessible disconnect device shall be incorporated in the building installation wiring.

zFor pluggable equipment, the socket-outlet shall be installed near the equipment and shall be easily accessible.

NOTICE (USA only):

zThis product has a High Intensity Discharge (HID) lamp that contains mercury. Disposal may be regulated

in your community due to environmental considerations. For disposal or recycling information, please visit

Panasonic website: http://www.panasonic.com/environmental or call 1-888-769-0149.

For USA-California Only

This product contains a CR Coin Cell Lithium Battery which contains Perchlorate Material – special handling

may apply.

See www.dtsc.ca.gov/hazardouswaste/perchlorate

ENGLISH - 3

Read this irst!

WARNING:

POWER

The wall outlet or the circuit breaker shall be installed near the equipment and shall be easily accessible

when problems occur. If the following problems occur, cut off the power supply immediately.

Continued use of the projector in these conditions will result in ire or electric shock.

zIf foreign objects or water get inside the projector, cut off the power supply.

zIf the projector is dropped or the cabinet is broken, cut off the power supply.

zIf you notice smoke, strange smells or noise coming from the projector, cut off the power supply.

Please contact an Authorized Service Center for repairs, and do not attempt to repair the projector yourself.

During a thunderstorm, do not touch the projector or the cable.

Electric shocks can result.

Do not do anything that might damage the power cord or the power plug.

If the power cord is used while damaged, electric shocks, short-circuits or ire will result.

zDo not damage the power cord, make any modiications to it, place it near any hot objects, bend it excessively, twist it, pull it, place heavy objects on top of it or wrap it into a bundle.

Ask an Authorized Service Center to carry out any repairs to the power cord that might be necessary.

Completely insert the power plug into the wall outlet and the power connector into the projector terminal.

If the plug is not inserted correctly, electric shocks or overheating will result.

z Do not use plugs which are damaged or wall outlets which are coming loose from the wall.

Do not use anything other than the provided power cord.

Failure to observe this will result in ire or electric shocks. Please note that if you do not use the provided power cord to ground the device on the side of the outlet, this may result in electric shocks.

Clean the power plug regularly to prevent it from becoming covered in dust.

Failure to observe this will cause a ire.

z If dust builds up on the power plug, the resulting humidity can damage the insulation. Pull the power plug out from the wall outlet and wipe it with a dry cloth regularly.

Do not handle the power plug and power connector with wet hands.

Failure to observe this will result in electric shocks.

Do not overload the wall outlet.

If the power supply is overloaded (ex., by using too many adapters), overheating may occur and ire will result.

ON USE/INSTALLATION

Do not place the projector on soft materials such as carpets or sponge mats.

Doing so will cause the projector to overheat, which can cause burns, ire or damage to the projector.

Do not set up the projector in humid or dusty places or in places where the projector may come into

contact with oily smoke or steam, ex. a bathroom.

Using the projector under such conditions will result in ire, electric shocks or deterioration of components. Deterioration of components (such as ceiling mount brackets) may cause the projector which is mounted on the ceiling to fall down.

Do not install this projector in a place which is not strong enough to take the full weight of the projector

or on top of a surface which is sloped or unstable.

Failure to observe this will cause projector to fall down or tip over the projector, and severe injury or damage could result.

4 - ENGLISH

Read this irst!

WARNING:

Do not cover the air intake/exhaust ports or place anything within 500 mm (20") of them.

Doing so will cause the projector to overheat, which can cause ire or damage to the projector.

zDo not place the projector in narrow, badly ventilated places.

zDo not place the projector on cloth or papers, as these materials could be drawn into the air inlet port.

Do not place your hands or other objects close to the air exhaust port.

Doing so will cause burns or damage your hands or other objects.

zHeated air comes out of the air exhaust port. Do not place your hands or face, or objects which cannot withstand heat close to this port.

Do not look at or place your skin into the light emitted from the lens while the projector is being used.

Doing so can cause burns or loss of sight.

zStrong light is emitted from the projector’s lens. Do not look at or place your hands directly into this light.

zBe especially careful not to let young children look into the lens. In addition, turn off the power and disconnect the power plug when you are away from the projector.

Never attempt to remodel or disassemble the projector.

High voltages can cause ire or electric shocks.

z For any inspection, adjustment and repair work, please contact an Authorized Service Center.

Do not project an image with the lens cover attached.

Doing so can cause ire.

Do not allow metal objects, lammable objects, or liquids to enter inside of the projector. Do not allow

the projector to get wet.

Doing so may cause short circuits or overheating, and result in ire, electric shock, or malfunction of the projector.

zDo not place containers of liquid or metal objects near the projector.

zIf liquid enters inside of the projector, consult your dealer.

zParticular attention must be paid to children.

Use the ceiling mount bracket speciied by Panasonic.

Using the ceiling mount bracket other than the speciied one will result in falling accidents.

zAttach the supplied safety cable to the ceiling mount bracket to prevent the projector from falling down.

Installation work (such as ceiling mount bracket) should only be carried out by a qualiied technician.

If installation is not carried out and secured correctly it can cause injury or accidents, such as electric shocks.

zDo not use anything other than an authorized ceiling mount bracket.

zBe sure to use the provided accessory wire with an eye bolt as an extra safety measure to prevent the projector from falling down. (Install in a different location to the ceiling mount bracket.)

ENGLISH - 5

Read this irst!

WARNING:

ACCESSORIES

Do not use or handle the batteries improperly, and refer to the following.

Failure to observe this will cause burns, batteries to leak, overheat, explode or catch ire.

zUse AA/R6 batteries.

zDo not use unspeciied batteries.

zDo not use chargeable batteries.

zDo not disassemble dry cell batteries.

zDo not heat the batteries or place them into water or ire.

zDo not allow the + and – terminals of the batteries to come into contact with metallic objects such as necklaces or hairpins.

zDo not store batteries together with metallic objects.

zStore the batteries in a plastic bag and keep them away from metallic objects.

zMake sure the polarities (+ and –) are correct when inserting the batteries.

zDo not use a new battery together with an old battery or mix different types of batteries.

zDo not use batteries with the outer cover peeling away or removed.

If the battery luid leaks, do not touch it with bare hands, and take the following measures if necessary.

zBattery luid on your skin or clothing could result in skin inlammation or injury. Rinse with clean water and seek medical advice immediately.

zBattery luid coming in contact with your eyes could result in loss of sight.

In this case, do not rub your eyes. Rinse with clean water and seek medical advice immediately.

Do not disassemble the lamp unit.

Doing so can cause electric shocks, burns, or injury.

Lamp replacement

The lamp has high internal pressure. If improperly handled, an explosion and severe injury or accidents will result.

zThe lamp can easily explode if struck against hard objects or dropped.

zBefore replacing the lamp, be sure to turn the power off and to disconnect the power plug from the wall

outlet.

Electric shocks or explosions can result if this is not done.

zWhen replacing the lamp, turn the power off and allow it to cool for at least one hour before handling it otherwise it can cause burns.

Do not use the supplied power cord with devices other than this projector.

zUsing the supplied power cord with devices other than this projector may cause short circuits or overheating, and result in electric shock or ire.

Remove the depleted batteries from the remote control promptly.

z Leaving them in the unit may result in luid leakage, overheating, or explosion of the batteries.

CAUTION:

POWER

When disconnecting the power cord, be sure to hold the power plug and power connector.

If the power cord itself is pulled, the lead will become damaged, and ire, short-circuits or serious electric shocks will result.

When not using the projector for an extended period of time, disconnect the power plug from the wall

outlet.

Failure to do so may result in ire or electric shock.

Disconnect the power plug from the wall outlet before carrying out any cleaning and replacing the unit.

Failure to do so may result in electric shock.

6 - ENGLISH

Read this irst!

CAUTION:

ON USE/INSTALLATION

Do not place heavy objects on top of the projector.

Failure to observe this will cause the projector to become unbalanced and fall, which could result in damage or injury. The projector will be damaged or deformed.

Do not put your weight on this projector.

You could fall or the projector could break, and injury will result.

z Be especially careful not to let young children stand or sit on the projector.

Do not place the projector in extremely hot locations.

Doing so will cause the outer casing or internal components to deteriorate, or result in ire. z Take particular care in locations exposed to direct sunlight or near stoves.

Do not place your hands in the openings beside the optical lens, while shifting the lens.

Failure to observe this could cause injury.

Do not stand in front of the lens while the projector is being used.

Doing so can cause damage and burns to clothing. z Strong light is emitted from the projector’s lens.

Do not place objects in front of the lens while the projector is being used.

Doing so can cause damage to the object and can cause the set to malfunction. z Strong light is emitted from the projector’s lens.

Always disconnect all cables before moving the projector.

Moving the projector with cables still attached can damage the cables, which will cause ire or electric shocks to occur.

ACCESSORIES

Do not use the old lamp unit.

If used it could cause lamp explosion.

If the lamp has broken, ventilate the room immediately. Do not touch or bring your face close to the

broken pieces.

Failure to observe this will cause the user to absorb the gas which was released when the lamp broke and which contains nearly the same amount of mercury as luorescent lamps, and the broken pieces will cause

injury.

zIf you believe that you have absorbed the gas or that the gas has got into your eyes or mouth, seek medical advice immediately.

zAsk your dealer about replacing the lamp unit and check the inside of the projector.

Do not attach the air ilter unit while it is wet.

Doing so may result in electric shock or malfunctions.

z After you clean the air ilter units, dry them thoroughly before reattaching them.

Do not touch the fan with your ingers or any other parts of your body when changing the lamp unit.

Doing so can cause injury.

Ask your dealer about cleaning inside the projector once a year.

Continuous use while dust is accumulated inside the projector may result in ire. z For cleaning fee, ask your dealer.

When not using the projector for an extended period of time, remove the batteries from the remote control.

Failure to observe this will cause the batteries to leak, overheat, catch ire or explode, which may result in ire or contamination of surrounding area.

ENGLISH - 7

Read this irst!

Brazil Only

Brasil Apenas

Manuseio de baterias usadas

BRASIL

Após o uso, as pilhas e /ou baterias poderão ser entregues ao estabelecimento comercial ou rede de assistência técnica autorizada.

Cobrir os terminais positivo (+) e negativo (-) com uma ita isolante adesiva, antes de depositar numa caixa destinada para o recolhimento. O contato entre partes metálicas pode causar vazamentos, gerar calor, romper

a blindagem e produzir fogo.

Não desmonte, não remova o invólucro, nem amasse a bateria. O gás liberado pela bateria pode irritar a garganta, daniicar o lacre do invólucro ou o vazamento provocar calor, ruptura da blindagem e produzir fogo

devido ao curto circuito dos terminais.

Não incinere nem aqueça as baterias, elas não podem icar expostas a temperaturas superiores a 100 °C (212 °F). O gás liberado pela bateria pode irritar a garganta,

daniicar o lacre do invólucro ou o vazamento provocar calor, ruptura da blindagem e produzir fogo devido ao

curto circuito dos terminais provocado internamente.

Evite o contato com o liquido que vazar das baterias. Caso isto ocorra, lave bem a parte afetada com bastante água. Caso haja irritação, consulte um médico.

Remoção das baterias

1. Pressione a guia e levante a tampa.

2. Remova as baterias.

(ii)

(i)

8 - ENGLISH

R Trademarks

•Microsoft®, Windows®, Windows Vista®, and Internet Explorer® are the registered trademarks or trademarks of

Microsoft Corporation in the United States and/or other countries.

•Mac, Mac OS, Mac OSX, and Safari are the trademarks of Apple Inc. registered in the United States and other countries.

•PJLinkTM is a trademark or pending trademark in Japan, the United States, and other countries and regions.

•HDMI, the HDMI logo and High-Deinition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC.

•VGA and XGA are trademarks of International Business Machines Corporation.

•SVGA is a registered trademark of the Video Electronics Standards Association.

•RoomView, Crestron RoomView, Crestron Connected, and Fusion RV are trademarks of Crestron Electronics,

Inc.

•The font used in the on-screen displays is a Ricoh bitmap font, which is manufactured and sold by Ricoh

Company, Ltd.

•Adobe Flash Player is either a trademark or registered trademark of Adobe Systems Incorporated in the

United States and/or other countries.

•Other names, company names or product names used in these operating instructions are the trademarks or

registered trademarks of their respective holders.

Please note that the operating instructions do not include the ® and TM symbols.

R Illustrations in these operating instructions

• Note that illustrations of the projector and screens may differ from the ones you actually see.

R Page references

• In these instructions, references to pages are indicated as: ( page 00).

R Term

•In these instructions, the “Wireless/wired remote control unit” accessories are referred to as the “Remote control”.

ENGLISH - 9

Features of the Projector

High luminance & High color reproducibility

The unique optical and lamp drive systems achieve a high luminance and high color reproducibility.

Easy setup and improved serviceability

Extensive lineup of optional lenses allow more lexible setup of the projector.

Improved cost performance in maintenance fee

The long life ilter reduces maintenance costs.

Quick Steps

For details, see the corresponding pages.

1.Set up the projector. (X page 26)

C

2.Attach the projection lens. (X page 35)

C

3.Connect with other devices. (X page 37)

C

4.Connect the power cord. (X page 41)

C

5.Switch on the projector. (X page 42)

C

6.Make initial settings.* (X page 19)

C

7.Select the input signal. (X page 45)

C

8.Adjust the image. (X page 45)

* These are the steps to be taken when you switch on the power for the irst time after purchasing the projector.

10 - ENGLISH

	Contents
Contents	Besuretoread“Readthisirst!”.(	X pages 2 to 8)
Read this irst!	............................................2 Projecting.................................................................	45
	Selecting the input signal .....................................	45

Chapter 1	Preparation
Precautions for use.................................................		14
Cautionswhentransporting ..................................		14
Cautionswheninstalling .......................................		14
Security ................................................................		15
Disposal................................................................		16
Cautions on use ...................................................		16
Software information regarding this product .........		16
Accessories..........................................................		17
Optional accessories............................................		18
Start-up display .......................................................		19
Initial setting (display language) ...........................		19
Initial setting (projector setup) ..............................		19
About your projector...............................................		20
Remote control.....................................................		20
Projector body ......................................................		21
Using the remote control........................................		23
Inserting and removing the batteries....................		23
Setting Remote control ID numbers .....................		23
Connecting to the projector with a cable ..............		24
Chapter 2	Getting Started
Setting up.................................................................		26
Projection method ................................................		26
Parts for ceiling mount (optional) ..........................		26
Screensizeandthrowdistance ...........................		27
Adjusting adjustable feet ......................................		34
Removing/attaching the projection lens ...............		35
Removing the projection lens...............................		35
Attaching the projection lens ................................		35
Connections.............................................................		37
Before connecting to the projector .......................		37
Connecting example: AV equipment ....................		38
Connecting example: Computers .........................		38
Chapter 3	Basic Operation
Switching on/off the projector................................		41
Connectingthepowercord ..................................		41
Power indicator.....................................................		42
Switchingontheprojector ....................................		42
Making adjustments and selections .....................		43
Switching off the projector ....................................		43
Direct power off function .......................................		44

Adjusting the focus, zoom, and shift.....................	45
Movingthelenstothehomeposition ...................	46
Adjustment range by the lens position shift
(optical shift)......................................................	46
Remote control operation.......................................	47
Using the shutter function.....................................	47
Usingtheon-screendisplayfunction ...................	47
Switching the input ...............................................	48
Using the status function......................................	48
Using the automatic setup function ......................	48
Using the function button......................................	49
Displaying the internal test pattern.......................	49
Changing the picture aspect ratio.........................	49
Chapter 4 Settings
Menu navigation ......................................................	51
Navigating through the menu ...............................	51
Main menu............................................................	52
Sub-menu.............................................................	52
[PICTURE] menu......................................................	55
[PICTUREMODE] ................................................	55
[CONTRAST]........................................................	55
[BRIGHTNESS] ....................................................	55
[COLOR]...............................................................	56
[TINT] ...................................................................	56
[COLOR TEMPERATURE]...................................	56
[WHITEGAIN] ......................................................	57
[SYSTEM DAYLIGHTVIEW] ................................	57
[SHARPNESS] .....................................................	58
[NOISE REDUCTION] ..........................................	58
[AI] ........................................................................	58
[SYSTEM SELECTOR] ........................................	59
[POSITION] menu ....................................................	60
[SHIFT] .................................................................	60
[ASPECT] .............................................................	60
[ZOOM].................................................................	61
[CLOCKPHASE] ..................................................	62
[KEYSTONE]........................................................	63
[ADVANCED MENU] menu......................................	64
[DIGITALCINEMAREALITY] ...............................	64
[BLANKING] .........................................................	64
[INPUT RESOLUTION] ........................................	65
[CLAMP POSITION] .............................................	65
[EDGEBLENDING] ..............................................	65
[RASTERPOSITION] ...........................................	66

ENGLISH - 11

Contents

[DISPLAY LANGUAGE] menu.................................	67
Changing the display language............................	67
[DISPLAY OPTION] menu........................................	68
[COLORMATCHING] ...........................................	68
[COLORCORRECTION] .....................................	69
[CONTRAST MODE] ............................................	69
[SCREENSETTING] ............................................	69
[AUTOSIGNAL] ...................................................	70
[AUTO SETUP].....................................................	70
[RGB IN] ...............................................................	70
[DVI-D IN] .............................................................	70
[HDMI IN] ..............................................................	71
[ON-SCREENDISPLAY] ......................................	71
[BACKCOLOR] ....................................................	72
[STARTUPLOGO] ................................................	72
[SHUTTERSETTING] ..........................................	73
[FREEZE] .............................................................	73
[SIDE BY SIDE](PT-DW740U only) ......................	73
[CUTOFF] ............................................................	74
[PROJECTOR SETUP] menu ..................................	75
[PROJECTOR ID] .................................................	75
[PROJECTIONMETHOD] ....................................	75
[COOLINGCONDITION] ......................................	76
[HIGHALTITUDEMODE] .....................................	76
[LAMPSELECT] ...................................................	76
[LAMPRELAY] .....................................................	77
[LAMP POWER] ...................................................	77
[STANDBY MODE] ...............................................	78
[SCHEDULE]........................................................	78
[STARTUPINPUTSELECT] ................................	79
[RS-232C].............................................................	80
[REMOTE2MODE] ..............................................	81
[STATUS]..............................................................	81
[NOSIGNALSHUT-OFF] .....................................	82
[FUNCTIONBUTTON] .........................................	82
[DATEAND TIME] ................................................	83
[SAVEALL USER DATA] ......................................	83
[LOADALLUSERDATA] .....................................	84
[INITIALIZE]..........................................................	84
[SERVICEPASSWORD] ......................................	84
[TEST PATTERN] menu...........................................	85
[TESTPATTERN] .................................................	85
[SIGNAL LIST] menu ...............................................	86
Registering a signal to the list ..............................	86
Renaming the registered data..............................	86
Deleting the registered data .................................	86
Protecting the registered data ..............................	87
Expanding signal lock-in range ............................	87
Managing the sub memory list .............................	87

[SECURITY] menu ...................................................		89
[SECURITY PASSWORD]....................................		89
[SECURITYPASSWORDCHANGE] ...................		89
[DISPLAY SETTING] ............................................		89
[TEXTCHANGE] ..................................................		90
[MENULOCK] ......................................................		90
[MENU LOCK PASSWORD] ................................		90
[CONTROL DEVICE SETUP] ...............................		90
[NETWORK] menu...................................................		92
[NETWORKSETUP] ............................................		92
[NETWORK CONTROL] ......................................		92
[NETWORK STATUS] ..........................................		93
Network connections ............................................		93
Accessing from the Web browser .........................		94
Chapter 5	Maintenance
Lamp/Temperature/Filter indicators ....................		110
Managing the indicated problems .......................		110
Maintenance/replacement.....................................		112
Before maintaining/replacing the unit ..................		112
Maintenance........................................................		112
Replacing the unit................................................		113
Troubleshooting ....................................................		116
Chapter 6	Appendix
Technical information ...........................................		118
PJLink protocol....................................................		118
ControlcommandsviaLAN .................................		119
<SERIALIN>/<SERIALOUT>terminal ..............		121
<REMOTE2IN>terminal ..................................		124
Two window display combination list
(PT-DW740U only) ..........................................		125
Menu lock password ...........................................		125
List of compatible signals ...................................		125
Speciications	........................................................	128
Dimensions ............................................................		130
Ceiling mount .......................bracket safeguards		131
Index .......................................................................		132

12 - ENGLISH

Chapter 1 Preparation

This chapter describes things you need to know or check before using the projector.

ENGLISH - 13

Chapter 1 Preparation — Precautions for use

Precautions for use

Cautions when transporting

F The projection lens is susceptible to effects from vibration or impact. Make sure to remove the projection lens when transporting.

Also, use a protection cover or the like to prevent dust from affecting the projection lens or the set.

F When transporting the projector, hold it securely by its bottom and avoid excessive vibration and impacts. They may damage the internal parts and result in malfunctions.

F Do not transport the projector with the adjustable feet extended. Doing so may damage the adjustable feet.

Cautions when installing

R Always attach the projection lens cover after attaching the projection lens.

If the cover is not attached, dust will accumulate inside and may cause malfunctions.

R Do not set up the projector outdoors.

The projector is designed for indoor use only.

R Do not set up the projector in the following locations.

F Places where vibration and impacts occur such as in a car or vehicle: Doing so may cause damage to internal parts or malfunction.

F Near the exhaust of an air conditioner: Depending on the conditions of use, the screen may luctuate in rare cases due to the hot air from the air exhaust port or the heated or cooled air. Make sure that the exhaust from the projector or other equipment, or the air from the air conditioner does not blow toward the front of the projector.

F Near lights (studio lamps, etc.) and other locations of great temperature luctuation (“Operating environment” (X page 129)): Doing so may shorten the life of the lamp or result in deformation of the outer case and malfunctions.

F Near high-voltage power lines or near motors: Doing so may interfere with the operation of the projector.

F Place where there is high-power laser equipment: Directing a laser beam onto the lens surface causes damage to the DLP chips.

R Be sure to ask a specialized technician or your dealer when installing the product to a ceiling.

If the product is to be installed hanging from the ceiling, purchase an optional Ceiling Mount Attachment. Model No.: ET-PKD56H (for high ceilings), ET-PKD55S (for low ceilings)

R Lens focus

The high clarity projection lens is thermally affected by the light from the light source, making the focus unstable in the period just after switching on the power. Wait at least 30 minutes with the image projected before adjusting the lens focus.

R Make sure to set [HIGH ALTITUDE MODE] to [ON] when using the projector at elevations of 1 400 m (4 593 ft) or higher and lower than 2 700 m (8 858 ft) above sea level.

Doing so may shorten the life of the internal parts and result in malfunctions.

R Make sure to set [HIGH ALTITUDE MODE] to [OFF] when using the projector at elevations lower than 1 400 m (4 593 ft) above sea level.

Doing so may shorten the life of the internal parts and result in malfunctions.

R Do not install the projector at elevations of 2 700 m (8 858 ft) or higher above sea level.

Doing so may shorten the life of the internal parts and result in malfunctions.

R Do not use the projector tilted to the right or left

Using the projector at a vertical angle that exceeds 15° may reduce product life or result in malfunction.

R When installing and using the projector at an angle that exceeds 30°vertically, set [COOLING CONDITION] (X page 76).

Failure to observe this will result in malfunctions or shorten the life of the lamp or other components.

R Cautions when setting up the projector

F To install and use the projector via a method that does not use the adjustable feet in a loor standing installation, ix the projector using the ive screw holes for ceiling mounting (Fig. 1).

(Screw diameter: M6, tapping depth inside the set: 12 mm (15/32"), torque: 4 ± 0.5 N·m)

14 - ENGLISH

Chapter 1 Preparation — Precautions for use

F Use the adjustable feet only for the loor standing installation and for adjusting the angle. Using it for other purposes may damage the set.

Screw holes for ceiling mount (M6)

Adjustable feet

Fig. 1 The positions of screw holes for ceiling mount and adjustable feet

F Do not stack projectors on top of each other.

F Do not use the projector tilted at an angle that exceeds ± 15° from the horizontal plane. F Do not block the ventilation ports (intake and exhaust) of the projector.

F Prevent hot and cool air from the air conditioning system from blowing directly to the ventilation ports (intake and exhaust) of the projector.

500 mm (20") or longer

500 mm (20") or longer

500 mm (20") or longer

100 mm (4") or longer

F Do not install the projector in a conined space.

When it is necessary to install the projector in a conined space, install the air conditioning or ventilation separately. Exhaust heat may accumulate when the ventilation is not enough, triggering the protection circuit of the projector.

F Make a clearance of at least 20 mm (0.8") between the projector bottom and setting surface by inserting spacers (metallic) etc. between them.

Security

When using this product, take safety measures against the following incidents.

F Personal information being leaked via this product F Unauthorized operation of this product by a malicious third party

F Interfering or stopping of this product by a malicious third party

Take suficient security measures. (X pages 89, 104) F Make your password dificult to guess as much as possible. F Change your password periodically.

F Panasonic Corporation or its afiliate companies will never ask for your password directly. Do not divulge your password in case you receive such inquiries.

F The connecting network must be secured by a irewall, etc.

F Set a password for the web control and restrict the users who can log in.

ENGLISH - 15

Chapter 1 Preparation — Precautions for use

Disposal

To dispose of the product, ask your local authorities or dealer for correct methods of disposal.

The lamp contains mercury. When disposing of used lamp units, contact your local authorities or dealer for correct methods of disposal.

Cautions on use

R To get a good picture quality

In order to view a beautiful image in higher contrast, prepare an appropriate environment. Draw curtains or blinds over windows and turn off any lights near the screen to prevent outside light or light from indoor lamps from shining onto the screen.

R Do not touch the surface of the projection lens with your bare hands.

If the surface of the projection lens becomes dirty from ingerprints or anything else, this will be magniied and projected onto the screen. Please put the lens cover (accessory) on the projector when you do not use it.

R DLP chips

F The DLP chips are precision-made. Note that in rare cases, pixels of high precision could be missing or always lit. Note that such phenomena does not indicate malfunction. This is not a malfunction.

F Directing a high-power laser beam onto the lens surface can damage the DLP chips.

R Do not move the projector while it is operating or subject it to vibration or impact.

Doing so may shorten the service life of its internal components.

R Lamp

The luminous source of the projector is a high-pressure mercury lamp. A high-pressure mercury lamp has the following characteristics. F The luminance of the lamp will decrease by duration of usage.

F The lamp may burst with a loud sound or have its service life shortened because of shock, chipping, or degradation due to cumulative operating time.

F The lamp life varies greatly depending on individual differences and usage conditions. In particular, frequently switching the power on/off accelerates lamp deterioration and greatly affects lamp life.

F Continuous use for one week or longer accelerates lamp deterioration. Lamp relay function (X page 77) can be used to reduce deterioration caused by continuous use.

F In rare cases, the lamps burst shortly after projection starts.

F The risk of bursting increases when the lamp is used beyond its replacement cycle. Make sure to replace the lamp unit regularly. (“When to replace the lamp unit” (X page 114), “Replacing the lamp unit” (X page 114))

F If the lamp bursts, gas contained inside of the lamp is released in a form of smoke. F It is recommended that you store replacement lamp units for contingency.

R About connections to computer or peripheral device

F To assure continued compliance, follow the attached installation instructions, which include using the provided power cord and shielded interface cables when connecting to computer or peripheral device.

F Use a commercial DVI-D cable with a ferrite core.

Software information regarding this product

© Panasonic Corporation 2012

This product incorporates the following software.

(1) The software which is developed independently by or for Panasonic Corporation (2)The software which is licensed under the GNU GENERAL PUBLIC LICENSE

(3)The software which is licensed under the GNU LESSER GENERAL PUBLIC LICENSE

For the license conditions of software categorized as (2) and (3), refer to the provisions of the Software license (GNU GENERAL PUBLIC LICENSE and GNU LESSER GENERAL PUBLIC LICENSE) in the supplied CD-ROM. (Those provisions are written in the original (English)

because they have been stipulated by third parties.)

If you have any questions regarding the software, contact ([e-mail]) by E-mail.

16 - ENGLISH

Chapter 1 Preparation — Precautions for use

Accessories

Make sure that the following accessories are provided with your projector. Numbers enclosed in < > show the number of accessories.

Wireless/wired remote control unit <1>

(N2QAYB000784)

Power cord <1>

(K2CG3YY00075)

Projection lens cover <1>

(TKPB35101)

Lens cover <1>

(TKKL5244)

(for models with attached lenses only)

CD-ROM <1>

(TXFQB02VLE3)

Power cord secure lock <1>

(TTRA0182)

AA/R6 battery <2>

(For remote control unit)

Attention

F After unpacking the projector, discard the power cord cap and packaging material properly.

F For missing accessories, consult your dealer.

F Store small parts in an appropriate manner, and keep them away from small children.

Note

F The model numbers of accessories and optional components are subject to change without notice.

Contents of the supplied CD-ROM

The contents of the supplied CD-ROM are as follows.

Instruction/list (PDF)	Operating Instructions - Functional Manual
	Multi Projector Monitoring & Control Software Operation Manual
	Logo Transfer Software Operating Manual
	List of Compatible Projector Models	This is a list of projectors that are compatible with the
		software contained in the CD-ROM and their restrictions.
	Software license	(GNU GENERAL PUBLIC LICENSE, GNU LESSER
		GENERAL PUBLIC LICENSE)
Software	Multi Projector Monitoring & Control Software	This software allows you to monitor and control multiple
	(Windows)	projectors connected to the LAN.
	Logo Transfer Software (Windows)	This software allows you to create original images, such
		as company logos to be displayed when projection starts,
		and transfer them to the projector.

ENGLISH - 17

Chapter 1 Preparation — Precautions for use

Optional accessories

Optional accessories (product name)	Model No.
	ET-DLE055 (ixed-focus lens), ET-DLE080 (ultra short-focus zoom lens), ET-DLE150 (short-
Projection lens	focus zoom lens), ET-DLE250 (medium-focus zoom lens), ET-DLE350 (long-focus zoom lens),
	ET-DLE450 (ultra long-focus zoom lens)
Ceiling mount bracket	ET-PKD56H (for high ceilings), ET-PKD55S (for low ceilings)
Replacement lamp unit	ET-LAD60A (1 pc), ET-LAD60AW (2 pcs)
Replacement ilter unit	ET-EMF300

18 - ENGLISH

Chapter 1 Preparation — Start-up display

Start-up display

The initial setting screen is displayed when the projector is switched on for the irst time after purchase as well as when [INITIALIZE] – [ALL USER DATA] (X page 84) is executed. Set them in accordance with circumstances.

In other occasions, you can change the settings by menu operations.

Note

F When the projector is used for the irst time, you may be required to adjust the focus, zoom, and shift to display the menu screen clearly. Refer to “Adjusting the focus, zoom, and shift” (X page 45) for details.

Initial setting (display language)

Select the language to show on the screen. (X page 67)

1) Press AS to select the display language.						2) Press the <ENTER> button to proceed to the
						initial setting.
		KPKVKCN"UGVVKPI

RNGCUG"UGNGEV"NCPIWCIG0

UGNGEV

GPVGT UGV

Initial setting (projector setup)

Set each item.

1)Press AS to select an item.

2)Press QW to switch the setting.

KPKVKCN"UGVVKPI

	RTQLGEVKQP"OGVJQF	HTQPV1HNQQT
	EQQNKPI"EQPFKVKQP	HNQQT"UGVVKPI
	UETGGP"HQTOCV	38 ;
	UETGGP"RQUKVKQP
	JKIJ"CNVKVWFG"OQFG	QHH

UYKVEJ"VQ"JKIJ"CNVKVWFG"OQFG"$QP$

KH"QXGT"3622o*67;5Hv+0

OGPW"UGNGEV EJCPIG

GPVGT UGV

F Refer to the following pages for details.

[PROJECTION METHOD] (X page 75) [COOLING CONDITION] (X page 76) [SCREEN FORMAT] (X page 69) [SCREEN POSITION] (X page 69) [HIGH ALTITUDE MODE] (X page 76)

3) Press the <ENTER> button.

F Conirm the setting value to complete the initial setting.

Note

F If you press the <MENU> button in the initial setting (projector setup) screen, you can go back to the initial setting (display language) screen.

ENGLISH - 19

Do not attempt to modify or disassemble the remote control.

Chapter 1 Preparation — About your projector

About your projector

Remote control

Front		Top
1
2		18
3	10
4
5	11
6	12	Bottom
	13
7	14	19
8
9	15
	16
	17

1Remote control indicator

Flashes if any button in the remote control is pressed.

2Power standby <V> button

Sets the projector to the standby mode when the <MAIN POWER> switch on the projector is set to <ON>.

3Power on <B> button

Starts projection when the <MAIN POWER> switch on the projector is set to <ON> and the power is switched off (standby mode).

4Input selection (<RGB1>, <RGB2>, <DVI-D>, <VIDEO>,

<S-VIDEO>, <HDMI>) buttons

Switches the input signal to project. (X page 48)

5<MENU> button/<ENTER> button/ASQW buttons

Used to operate the menu screen. (X page 51)

6<ON SCREEN> button

Switches the on-screen display function on (displayed)/off (hidden). (X page 47)

7<TEST PATTERN> button

Displays the test pattern. (X page 49)

8Number (<0> - <9>) buttons

Used when the system uses multiple projectors. Used to input ID numbers or passwords.

9<STATUS> button

Displays the projector information.

10<AUTO SETUP> button

Automatically adjusts the image display position while projecting

the image.

[PROGRESS] is displayed on the screen while the image is adjusted automatically. (X page 48)

11<SHUTTER> button

Use to temporarily turn off the image. (X page 47)

12<ASPECT> button

Switches the aspect ratio of the image. (X page 49)

13Lens (<FOCUS>, <ZOOM>, <SHIFT>) buttons

Adjusts the projection lens. (X pages 43, 45)

14<FUNCTION> button

You can assign a frequently used operation as a shortcut button. (X page 49)

15<DEFAULT> button

Resets the content of the sub-menu to the factory default. (X page 51)

16<ID SET> button

Sets the ID number of the remote control when a system uses multiple projectors. (X page 23)

17<ID ALL> button

Use to simultaneously control all the projectors with one remote control when a system uses multiple projectors. ( X page 23)

18Remote control signal transmitter

19Remote control wired terminal

Connecting to the projector with a cable (X page 24)

Attention

F Do not drop the remote control.

F Avoid contact with liquids or moisture.

F

Note

F

F F F

F

The remote control can be used within a distance of about 30 m (98'5") if pointed directly at the remote control receiver. The remote control can control at angles of up to ±15° vertically and ±30° horizontally, but the effective control range may be reduced.

If there are any obstacles between the remote control and the remote control signal receiver, the remote control may not operate properly. The signal will be relected off the screen. However, the operating range may be limited from light relection loss due to the screen material. If the remote control signal receiver directly receives strong light, such as luorescent light, the remote control may not operate properly.

Use it in a place distant from the light source.

The power indicator <ON (G)/STANDBY (R)> will lash if the projector receives a remote control signal.

20 - ENGLISH

Chapter 1 Preparation — About your projector

Projector body

	Front													Side
1			2			3			4		5		13			14		13

Front

							15	16	17
	6		7	8	6

Rear

			Front
9	10	11	12	13	18	13
Bottom			8	Projection lens
				(for models with attached lenses only)
13	19		9	Air exhaust port
			10	Lamp unit cover (X page 114)
			11	Control panel (X page 22)
			12	Remote control signal receiver (rear)
			13	Air intake port
			14	Connecting terminals (X page 22)
			15	<MAIN POWER> switch
				Turns on/off the main power.
Front			16	Security slot
				This security slot is compatible with the Kensington security
13				cables.
			17	<AC IN> terminal
				Connect the supplied power cord.
			18	Air ilter cover
				The air ilter unit is inside. (X page 112)
Warning			19	Burglar hook port
				You can attach a commercial burglar prevention cable.

Keep your hands and other objects away from the air exhaust

port.

F Keep your hands and face away. F Do not insert your ingers. F Keep heat-sensitive objects away.

Heated air from the air outlet port can cause bums, injury, or deformations.

1Power indicator <ON (G)/STANDBY (R)>

Displays the status of the power.

2Lamp indicator <LAMP1>

Displays the status of lamp 1.

3Lamp indicator <LAMP2>

Displays the status of lamp 2.

4Temperature indicator <TEMP>

Displays the internal temperature status.

5Filter indicator <FILTER>

Displays the status of the air ilter unit.

6Adjustable feet

Adjusts the projection angle.

7Remote control signal receiver (front)

ENGLISH - 21

Chapter 1 Preparation — About your projector

R Control panel

1

2

3

4

5

6

7

8

1Power standby <V> button

Sets the projector to the standby mode when the <MAIN POWER> switch on the projector is set to <ON>.

2Power on <B> button

Starts projection when the <MAIN POWER> switch on the projector is set to <ON> when the power is switched off (standby mode).

3<VIDEO> button

Switches to VIDEO input.

4<S-VIDEO> button

Switches to S-VIDEO input.

5<RGB1> button

Switches to RGB1 input.

6<RGB2> button

Switches to RGB2 input.

7<DVI-D> button

Switches to DVI-D input.

8<HDMI> button

Switches to HDMI input.

9

10

11 12

13

14

9<MENU> button

Displays and erases the main menu.

Returns to the previous screen when a sub-menu is displayed. (X page 51)

If you press the <MENU> button on the control panel for at least three seconds while the on-screen indication is off, the on- screen display is turned on.

10<LENS> button

Adjusts the focus, zoom, and shift (position) of the lens.

11<ENTER> button

Determines and executes an item in the menu screen.

12<SHUTTER> button

Use to temporarily turn off the image. (X page 47)

13ASQW selection buttons

Use to select items in the menu screen, change settings, and

adjust levels.

It is also used to enter [SECURITY] passwords.

14<AUTO SETUP> button

Automatically adjusts the image display position while projecting

the image.

[PROGRESS] is displayed on the screen while the image is adjusted automatically. (X page 48)

R Connecting terminals

1		2				3							4																									5													6

	7	8	9	10	11
1	<LAN> terminal		7	<REMOTE 1 IN> terminal / <REMOTE 1 OUT> terminal
	This is a terminal to connect to the network.			These are the terminals to connect the remote control for serial
	Used for control and monitoring. Image input through network			control when the system uses multiple projectors.
	connections is not possible.		8	<REMOTE 2 IN> terminal
2	<VIDEO IN> terminal			This is a terminal to remotely control the projector using the
	This is a terminal to input video signals.			external control circuit.
3	<S-VIDEO IN> terminal		9	<SERIAL IN> terminal
	This is a terminal to input S video signals.			This is a RS-232C compatible terminal to externally control the
4	<RGB 1 IN> (<R/PR>, <G/Y>, <B/PB>, <SYNC/HD>, <VD>)			projector by connecting a computer.
	terminal		10	<SERIAL OUT> terminal
	This is a terminal to input RGB signals or YCBCR/YPBPR signals.			This is a terminal to output the signal connected to the serial
5	<HDMI IN> terminal			input terminal.
	This is a terminal to input HDMI signals.		11	<RGB 2 IN> terminal
6	<DVI-D IN> terminal			This is a terminal to input RGB signals or YCBCR/YPBPR signals.

This is a terminal to input DVI-D signals.

Attention

F When a LAN cable is directly connected to the projector, the network connection must be made indoors.

22 - ENGLISH

Chapter 1 Preparation — Using the remote control

Using the remote control

Inserting and removing the batteries

1) Open the cover.	2) Insert the batteries and close the cover (insert
	the M side first).

(ii)

(i)

F When removing the batteries, perform the steps in reverse order.

Setting Remote control ID numbers

When you use the system with multiple projectors, you can operate all the projectors simultaneously or each projector individually using single remote control, if a unique ID number is assigned to each projector.

After setting the ID number of the projector, set the same ID number on the remote control.

The factory default ID number of the projector is set to [ALL]. When using a single projector, press the <ID ALL> button on the remote control. Also, you can control a projector if you press the <ID ALL> button on the remote control even if you do not know the projector ID.

How to set

1)Press the <ID SET> button on the remote control.

2)Within five seconds, press the two-digit ID number set on the projector using the number (<0> - <9>) buttons.

F If you press the <ID ALL> button, you can operate the projectors regardless of the setting of the projector’s ID number.

Attention

F

F

Since the ID number of the remote control can be set without the projector, do not press the <ID SET> button carelessly. If the <ID SET> button is pressed and no number (<0> - <9>) buttons are pressed within the next ive seconds, the ID number returns to its original value before the <ID SET> button was pressed.

The ID number set on the remote control will be stored unless it is set again. However, it will be erased if the remote control is left with dead batteries. Set the same ID number again when the batteries are replaced.

Note

F Set the ID number of the projector from the [PROJECTOR SETUP] menu → [PROJECTOR ID] (X page 75).

ENGLISH - 23

Chapter 1 Preparation — Using the remote control

Connecting to the projector with a cable

When you use the system with multiple projectors, conigure the units as in the following igure. Use a commercial M3 stereo mini jack cable and connect the other devices to the <REMOTE 1 IN>/<REMOTE 1 OUT> terminals of the projector.

The remote control is effective even in places where an obstacle stands in the light path or where devices are susceptible to outside light.

Connecting terminals

Connect to the second projector

M3 stereo mini jack cable (commercially available)

Remote

Connect to remote control wired terminal

Attention

F Use a cable that is 15 m (49'2") or shorter, with 2 core shield. The remote control may not operate when the length of the cable exceeds 15 m (49'2") or when the shielding of the cable is inadequate.

24 - ENGLISH

Chapter 2 Getting Started

This chapter describes about things you need to do before using the projector such as the setup and connections.

ENGLISH - 25

Chapter 2 Getting Started — Setting up

Setting up

Projection method

You can use the projector with any of the following four projection methods. Select the appropriate method depending on the environment.

Mounting on the ceiling and projecting forward	Setting on a desk/loor and projecting from rear
	(Using the translucent screen)

Menu item*	Method	Menu item*	Method
[PROJECTION METHOD]	[FRONT/CEILING]	[PROJECTION METHOD]	[REAR/FLOOR]
[COOLING CONDITION]	[CEILING SETTING]	[COOLING CONDITION]	[FLOOR SETTING]
Mounting on the ceiling and projecting from rear		Setting on a desk/loor and projecting forward
(Using the translucent screen)

Menu item*	Method	Menu item*	Method
[PROJECTION METHOD]	[REAR/CEILING]	[PROJECTION METHOD]	[FRONT/FLOOR]
[COOLING CONDITION]	[CEILING SETTING]	[COOLING CONDITION]	[FLOOR SETTING]

*For menu item details, refer to the [PROJECTOR SETUP] menu → [PROJECTION METHOD] (X page 75) and [COOLING CONDITION] (X page 76).

Parts for ceiling mount (optional)

You can install the projector on the ceiling using the optional ceiling mount bracket (ET-PKD56H: for high ceilings, or ET-PKD55S: for low ceilings).

F Use only the ceiling mount brackets speciied for this projector.

F Refer to the installation manual for the ceiling mount bracket when installing the bracket and the projector.

Attention

F To ensure projector performance and security, installation of the ceiling mount bracket must be carried out by your dealer or a qualiied technician.

26 - ENGLISH

Chapter 2 Getting Started — Setting up

Screen size and throw distance

Refer to the following igures and table describing projection distances to install the projector. Image size and image position can be adjusted in accordance with the screen size and screen position.

Projection screen

			SD
SH

SW

L (LW/LT)*

SH

SW

H

SD

							Screen
SH
							L (LW/LT)
	H

SW							L (LW/LT)
							Screen

Projection distance (m)

Image height (m)

Image width (m)

Distance (m) from the lens center to the bottom edge of the image

Image diagonal size (m)

*LW: Minimum projection distance when the zoom lens is used LT: Maximum projection distance when the zoom lens is used

Attention

F Before setting up, read “Precautions for use” (X pages 14 to 18).

F Do not use the projector and the high-powered laser equipment in the same room.

Hitting of a laser beam on to the lens can damage the DLP chips.

ENGLISH - 27

Chapter 2 Getting Started — Setting up

Projection distance per projection lens

For PT-DW740U

R When the screen aspect is 16:10 (unit: m)

(The dimensions of the following table contain slight error.)

										Optional lens
Lens type			Standard zoom lens			Fixed-		Ultra-short focus			Short focus zoom			Medium focus zoom
						focus		zoom lens			lens					lens
						lens
Projection lens Model No.						ET-DLE055		ET-DLE080			ET-DLE150			ET-DLE250
Throw ratio*1			1.8 – 2.5:1			0.8:1		0.8 – 1.0:1			1.4 – 2.0:1			2.4 – 3.8:1
Projection screen size								Projection distance (L)
Screen diagonal	Height	Width	Min.		Max.	Fixed		Min.	Max.		Min.		Max.	Min.			Max.
(SD)	(SH)	(SW)
1.27 (50")	0.673	1.077	1.91		2.70	0.87		0.87	1.09		1.45		2.12	2.54			4.06
1.52 (60")	0.808	1.292	2.31		3.26	1.06		1.05	1.32		1.75		2.55	3.07			4.89
1.78 (70")	0.942	1.508	2.71		3.81	1.24		1.23	1.54		2.05		2.98	3.59			5.72
2.03 (80")	1.077	1.723	3.11		4.37	1.42		1.42	1.77		2.35		3.42	4.12			6.55
2.29 (90")	1.212	1.939	3.50		4.92	1.61		1.60	2.00		2.65		3.85	4.64			7.38
2.54 (100")	1.346	2.154	3.90		5.48	1.79		1.78	2.22		2.95		4.28	5.16			8.20
3.05 (120")	1.615	2.585	4.70		6.59	2.16		2.15	2.68		3.55		5.15	6.21			9.86
3.81 (150")	2.019	3.231	5.89		8.25	2.71		2.70	3.36		4.45		6.45	7.79			12.35
5.08 (200")	2.692	4.308	7.88		11.03	3.63		3.61	4.49		5.95		8.61	10.41			16.49
6.35 (250")	3.365	5.385	9.86		13.81			4.53	5.62		7.45		10.78	13.03			20.63
7.62 (300")	4.039	6.462	11.85		16.58			5.45	6.76		8.95		12.95	15.65			24.77
8.89 (350")	4.712	7.539	13.84		19.36			6.36	7.89		10.46		15.11	18.28			28.91
10.16 (400")	5.385	8.616	15.83		22.13			7.28	9.02		11.96		17.28	20.90			33.05
12.7 (500")	6.731	10.770	19.80		27.68			9.11	11.29		14.96		21.61	26.14			41.34
15.24 (600")	8.077	12.923	23.78		33.23			10.94	13.55		17.96		25.94	31.39			49.62
					Optional lens						Height position
Lens type
			Long focus zoom			Ultra-long focus
											(H)*2
				lens		zoom lens
Projection lens Model No.			ET-DLE350			ET-DLE450			Standard zoom
									lens/
Throw ratio*1			3.8 – 5.7:1			5.6 – 9.0:1
									ET-DLE080/				ET-DLE055
Projection screen size				Projection distance (L)
									ET-DLE150/
													(Fixed)
									ET-DLE250/
Screen diagonal	Height	Width
			Min.		Max.	Min.		Max.	ET-DLE350/
(SD)	(SH)	(SW)
									ET-DLE450
1.27 (50")	0.673	1.077	4.00		6.11	5.96		9.59	-0.07 - 0.34				0.34
1.52 (60")	0.808	1.292	4.83		7.36	7.21		11.57	-0.08 - 0.40				0.40
1.78 (70")	0.942	1.508	5.65		8.61	8.46		13.55	-0.09 - 0.47				0.47
2.03 (80")	1.077	1.723	6.48		9.86	9.71		15.53	-0.11 - 0.54				0.54
2.29 (90")	1.212	1.939	7.31		11.11	10.96		17.51	-0.12 - 0.61				0.61
2.54 (100")	1.346	2.154	8.13		12.36	12.21		19.49	-0.13 - 0.67				0.67
3.05 (120")	1.615	2.585	9.79		14.86	14.72		23.45	-0.16 - 0.81				0.81
3.81 (150")	2.019	3.231	12.27		18.61	18.47		29.38	-0.20 - 1.01				1.01
5.08 (200")	2.692	4.308	16.40		24.85	24.73		39.28	-0.27 - 1.35				1.35
6.35 (250")	3.365	5.385	20.53		31.10	30.99		49.17	-0.34 - 1.68
7.62 (300")	4.039	6.462	24.67		37.34	37.25		59.06	-0.40 - 2.02
8.89 (350")	4.712	7.539	28.80		43.59	43.51		68.96	-0.47 - 2.36
10.16 (400")	5.385	8.616	32.94		49.84	49.76		78.85	-0.54 - 2.69
12.7 (500")	6.731	10.770	41.20		62.33	62.28		98.64	-0.67 - 3.37
15.24 (600")	8.077	12.923	49.47		74.82	74.80		118.42	-0.81 - 4.04

*1 The throw ratio is based on the value during projection onto a 2.03-m (80") screen size.

*2 The height position (H) is SH/2 because lens shift cannot be used when a ixed-focus lens (Model No.:ET-DLE055) is attached.

28 - ENGLISH

Chapter 2 Getting Started — Setting up

R When the screen aspect is 16:9 (unit: m)

(The dimensions of the following table contain slight error.)

										Optional lens
Lens type			Standard zoom lens			Fixed-		Ultra-short focus			Short focus zoom			Medium focus zoom
						focus		zoom lens			lens					lens
						lens
Projection lens Model No.						ET-DLE055		ET-DLE080			ET-DLE150			ET-DLE250
Throw ratio*1			1.8 – 2.5:1			0.8:1		0.8 – 1.0:1			1.4 – 2.0:1			2.4 – 3.8:1
Projection screen size								Projection distance (L)
Screen diagonal	Height	Width	Min.		Max.	Fixed		Min.	Max.		Min.		Max.	Min.			Max.
(SD)	(SH)	(SW)
1.27 (50")	0.623	1.107	1.97		2.78	0.90		0.89	1.12		1.49		2.18	2.62			4.18
1.52 (60")	0.747	1.328	2.38		3.35	1.09		1.08	1.35		1.80		2.62	3.15			5.03
1.78 (70")	0.872	1.550	2.79		3.92	1.27		1.27	1.59		2.11		3.07	3.69			5.88
2.03 (80")	0.996	1.771	3.19		4.49	1.46		1.46	1.82		2.42		3.51	4.23			6.73
2.29 (90")	1.121	1.992	3.60		5.06	1.65		1.65	2.05		2.72		3.96	4.77			7.58
2.54 (100")	1.245	2.214	4.01		5.63	1.84		1.83	2.29		3.03		4.40	5.31			8.43
3.05 (120")	1.494	2.657	4.83		6.77	2.22		2.21	2.75		3.65		5.29	6.39			10.14
3.81 (150")	1.868	3.321	6.05		8.49	2.79		2.78	3.45		4.58		6.63	8.01			12.69
5.08 (200")	2.491	4.428	8.10		11.34	3.73		3.72	4.61		6.12		8.86	10.70			16.95
6.35 (250")	3.113	5.535	10.14		14.19			4.66	5.78		7.66		11.08	13.40			21.21
7.62 (300")	3.736	6.641	12.18		17.04			5.60	6.94		9.21		13.31	16.09			25.46
8.89 (350")	4.358	7.748	14.23		19.90			6.54	8.11		10.75		15.53	18.79			29.72
10.16 (400")	4.981	8.855	16.27		22.75			7.48	9.27		12.29		17.76	21.48			33.98
12.7 (500")	6.226	11.069	20.35		28.45			9.36	11.60		15.38		22.21	26.87			42.49
15.24 (600")	7.472	13.283	24.44		34.16			11.24	13.93		18.46		26.66	32.26			51.00
					Optional lens						Height position
Lens type
			Long focus zoom			Ultra-long focus
											(H)*2
				lens		zoom lens
Projection lens Model No.			ET-DLE350			ET-DLE450			Standard zoom
									lens/
Throw ratio*1			3.8 – 5.7:1			5.6 – 9.0:1
									ET-DLE080/				ET-DLE055
Projection screen size				Projection distance (L)
									ET-DLE150/
													(Fixed)
									ET-DLE250/
Screen diagonal	Height	Width
			Min.		Max.	Min.		Max.	ET-DLE350/
(SD)	(SH)	(SW)
									ET-DLE450
1.27 (50")	0.623	1.107	4.11		6.29	6.13		9.87	-0.14 - 0.31				0.31
1.52 (60")	0.747	1.328	4.96		7.57	7.42		11.90	-0.16 - 0.37				0.37
1.78 (70")	0.872	1.550	5.81		8.85	8.70		13.94	-0.19 - 0.44				0.44
2.03 (80")	0.996	1.771	6.66		10.14	9.99		15.97	-0.22 - 0.50				0.50
2.29 (90")	1.121	1.992	7.51		11.42	11.28		18.00	-0.25 - 0.56				0.56
2.54 (100")	1.245	2.214	8.36		12.71	12.56		20.04	-0.27 - 0.62				0.62
3.05 (120")	1.494	2.657	10.06		15.27	15.14		24.11	-0.33 - 0.75				0.75
3.81 (150")	1.868	3.321	12.61		19.13	18.99		30.21	-0.41 - 0.93				0.93
5.08 (200")	2.491	4.428	16.86		25.55	25.43		40.38	-0.55 - 1.25				1.25
6.35 (250")	3.113	5.535	21.11		31.97	31.86		50.54	-0.68 - 1.56
7.62 (300")	3.736	6.641	25.36		38.39	38.29		60.71	-0.82 - 1.87
8.89 (350")	4.358	7.748	29.61		44.81	44.72		70.88	-0.96 - 2.18
10.16 (400")	4.981	8.855	33.86		51.23	51.16		81.05	-1.10 - 2.49
12.7 (500")	6.226	11.069	42.35		64.07	64.02		101.39	-1.37 - 3.11
15.24 (600")	7.472	13.283	50.85		76.91	76.88		121.73	-1.64 - 3.74

*1 The throw ratio is based on the value during projection onto a 2.03-m (80") screen size.

*2 The height position (H) is SH/2 because lens shift cannot be used when a ixed-focus lens (Model No.:ET-DLE055) is attached.

ENGLISH - 29

Chapter 2 Getting Started — Setting up

R When the screen aspect is 4:3 (unit: m)

(The dimensions of the following table contain slight error.)

										Optional lens
Lens type			Standard zoom lens			Fixed-		Ultra-short focus			Short focus zoom			Medium focus zoom
						focus		zoom lens			lens					lens
						lens
Projection lens Model No.						ET-DLE055		ET-DLE080			ET-DLE150			ET-DLE250
Throw ratio*1			2.2 – 3.0:1			1.0:1		1.0 – 1.2:1			1.6 – 2.4:1			2.9 – 4.6:1
Projection screen size								Projection distance (L)
Screen diagonal	Height	Width	Min.		Max.	Fixed		Min.	Max.		Min.		Max.	Min.			Max.
(SD)	(SH)	(SW)
1.27 (50")	0.762	1.016	2.18		3.07	0.99		0.99	1.24		1.65		2.40	2.89			4.61
1.52 (60")	0.914	1.219	2.63		3.70	1.20		1.20	1.50		1.99		2.89	3.48			5.55
1.78 (70")	1.067	1.422	3.08		4.33	1.41		1.40	1.75		2.33		3.38	4.08			6.48
2.03 (80")	1.219	1.626	3.53		4.95	1.62		1.61	2.01		2.67		3.87	4.67			7.42
2.29 (90")	1.372	1.829	3.98		5.58	1.82		1.82	2.26		3.00		4.36	5.26			8.36
2.54 (100")	1.524	2.032	4.42		6.21	2.03		2.03	2.52		3.34		4.85	5.86			9.30
3.05 (120")	1.829	2.438	5.32		7.47	2.45		2.44	3.03		4.02		5.83	7.04			11.17
3.81 (150")	2.286	3.048	6.67		9.35	3.07		3.06	3.80		5.04		7.31	8.82			13.98
5.08 (200")	3.048	4.064	8.92		12.49	4.11		4.10	5.09		6.74		9.76	11.79			18.67
6.35 (250")	3.810	5.080	11.17		15.64			5.13	6.37		8.44		12.21	14.76			23.36
7.62 (300")	4.572	6.096	13.42		18.78			6.17	7.65		10.14		14.66	17.73			28.05
8.89 (350")	5.334	7.112	15.67		21.92			7.21	8.93		11.84		17.11	20.70			32.74
10.16 (400")	6.096	8.128	17.92		25.06			8.24	10.22		13.54		19.56	23.67			37.42
12.7 (500")	7.620	10.160	22.42		31.34			10.31	12.78		16.94		24.47	29.60			46.80
15.24 (600")	9.144	12.192	26.92		37.63			12.39	15.35		20.34		29.37	35.54			56.17
					Optional lens						Height position
Lens type
			Long focus zoom			Ultra-long focus
											(H)*2
				lens		zoom lens
Projection lens Model No.			ET-DLE350			ET-DLE450			Standard zoom
									lens/
Throw ratio*1			4.5 – 6.9:1			6.8 – 10.8:1
									ET-DLE080/				ET-DLE055
Projection screen size				Projection distance (L)
									ET-DLE150/
													(Fixed)
									ET-DLE250/
Screen diagonal	Height	Width
			Min.		Max.	Min.		Max.	ET-DLE350/
(SD)	(SH)	(SW)
									ET-DLE450
1.27 (50")	0.762	1.016	4.54		6.94	6.78		10.90	-0.08 - 0.38				0.38
1.52 (60")	0.914	1.219	5.48		8.35	8.20		13.14	-0.09 - 0.46				0.46
1.78 (70")	1.067	1.422	6.42		9.76	9.61		15.38	-0.11 - 0.53				0.53
2.03 (80")	1.219	1.626	7.35		11.18	11.03		17.62	-0.12 - 0.61				0.61
2.29 (90")	1.372	1.829	8.29		12.59	12.45		19.86	-0.14 - 0.69				0.69
2.54 (100")	1.524	2.032	9.22		14.01	13.87		22.10	-0.15 - 0.76				0.76
3.05 (120")	1.829	2.438	11.09		16.83	16.70		26.58	-0.18 - 0.91				0.91
3.81 (150")	2.286	3.048	13.90		21.08	20.95		33.30	-0.23 - 1.14				1.14
5.08 (200")	3.048	4.064	18.58		28.15	28.03		44.49	-0.30 - 1.52				1.52
6.35 (250")	3.810	5.080	23.26		35.22	35.12		55.69	-0.38 - 1.91
7.62 (300")	4.572	6.096	27.94		42.29	42.20		66.89	-0.46 - 2.29
8.89 (350")	5.334	7.112	32.62		49.36	49.28		78.09	-0.53 - 2.67
10.16 (400")	6.096	8.128	37.30		56.43	56.37		89.29	-0.61 - 3.05
12.7 (500")	7.620	10.160	46.65		70.57	70.53		111.68	-0.76 - 3.81
15.24 (600")	9.144	12.192	56.01		84.71	84.70		134.08	-0.91 - 4.57

*1 The throw ratio is based on the value during projection onto a 2.03-m (80") screen size.

*2 The height position (H) is SH/2 because lens shift cannot be used when a ixed-focus lens (Model No.:ET-DLE055) is attached.

30 - ENGLISH