Panasonic PT-DW11K User Manual
PEC
S
ILE
F
Product Number :
Product Name :
PT-DW11K
3-Chip DLP™Projector
As of April 2013. Specifications and appearance are subject to change without notice.
SFD12M022
1/18
S PEC F ILE
3-Chip DLP™Projector
PT-DW11K
Specifications
Main unit
Power supply
Power consumption
120 V AC, 50/60 Hz
220–240 V AC, 50/60 Hz
DLP™ chip Panel size
Display method
Pixels
Lens
Lamp
Screen size
Brightness*
Center-to-corner uniformity*
Contrast*
2
2
2
Resolution
Scanning frequency
HDMI/DVI-D/RGB
YP
(YCBCR)
BPR
Video/S-Video
Optical axis shift Vertical
Horizontal
Keystone correction range
Installation Ceiling/floor, front/rear
Terminals HDMI IN HDMI 19-pin × 1, Deep Color, compatible with HDCP,
120 V AC, 9.1 A, 50/60 Hz
220–240 V AC, 4.8 A, 50/60 Hz
980 W (1,010 VA) (0.2 W with standby mode set to eco.*
standby mode set to normal. Both with fan stopped.)
950 W (980 VA) (0.3 W with standby mode set to eco.*1 9 W with
standby mode set to normal. Both with fan stopped.)
21.6 mm (0.85 inches) diagonal (16:9 aspect ratio)
DLP™ chip × 3 (R, G, B), DLP™ projection system
1,049,088 (1,366 × 768) × 3, total of 3,147,264 pixels
Optional powered zoom/focus lenses
380 W UHM lamps (× 2) (dual lamp, high mode)
1.78–25.4 m (70–1,000 inches) (1.78–15.24 m (70–600 inches) with the
ET-D75LE8), 16:10 aspect ratio
11,000 lumens (dual lamp, high mode)
90%
10,000:1 (full on/full off, in dynamic iris 3 mode)
1,366 × 768 pixels (Input signals that exceed this resolution will be
converted to 1,366 × 768 pixels.)
Horizontal: 15 kHz–100 kHz, vertical: 24 Hz – 120 Hz,
dot clock: 25–162 MHz or lower (HDMI/DVI: 25 MHz – 162 MHz)
525i (480i): f
625i (576i): f
525p (480p): f
625p (576p): f
750 (720)/60p: f
750 (720)/50p: f
1125 (1035)/60i: f
1125 (1080)/60i: f
1125 (1080)/50i: f
1125 (1080)/25p: f
1125 (1080)/24p: f
1125 (1080)/24sF: f
1125 (1080)/30p: f
1125 (1080)/60p: f
1125 (1080)/50p: f
f
H: 15.75 kHz, fV: 60 Hz [NTSC/NTSC4.43/PAL-M/PAL60]
15.75 kHz; fV60 Hz,
H
H
15.63 kHz; fV50 Hz,
31.50 kHz; fV60 Hz,
H
H
31.25 kHz; fV50 Hz,
45.00 kHz; fV60 Hz,
H
37.50 kHz; fV50 Hz,
H
H
33.75 kHz; fV60 Hz,
33.75 kHz; fV60 Hz,
H
H
28.13 kHz; fV50 Hz,
28.13 kHz; fV25 Hz,
H
27.00 kHz; fV24 Hz,
H
H
27.00 kHz; fV48 Hz,
33.75 kHz; fV30 Hz,
H
H
67.50 kHz; fV60 Hz,
56.25 kHz; fV50 Hz
H
fH: 15.63 kHz, fV: 50 Hz [PAL/PAL-N/SECAM]
±70% (±60% with the ET-D75LE6) from center of screen, powered
±30% (±20% with the ET-D75LE6) from center of screen, powered
NOTE: Optical axis shift function cannot be operated when used with the
ET-D75LE50.
Vertical ±40°
(vertical ±22° with the ET-D75LE5/LE50,
vertical ±28° with the ET-D75LE6)
525i(480i)*3, 625i(576i)*3, 525p(480p), 625p(576p), 750(720)/60p,
750(720)50p, 1125(1080)/60i, 1125(1080)/50i, 1125(1080)/25p,
1125(1080)/24p, 1125(1080)/24sF, 1125(1080)/30p, 1125(1080)/60p,
1125(1080)/50p
VGA (640 × 480) – WUXGA*
4
(1,920 × 1,200),
dot clock: 25 MHz –162 MHz
NOTE: Compatible with non-interlaced signals only.
1
6 W with
As of April 2013
SFD12M022
2/18
S PEC F ILE
3-Chip DLP™Projector
DVI-D IN
RGB 1 IN
RGB 2 IN
VIDEO IN
3D SYNC 1 IN/OUT
3D SYNC 2 OUT
SERIAL IN
SERIAL OUT
REMOTE 1 IN
REMOTE 1 OUT
REMOTE 2 IN
LAN
Power cord length
Cabinet materials
Dimensions (W ×H × D):
6
Weight*
Operation noise*
Operating temperature
Operating humidity
2
R, G, B
B, PR (Y, CB, CR)
Y, P
S-Video signal
R, G, B
Y, P
, PR(Y, CB, CR)
B
PT-DW11K
DVI-D 24-pin × 1, DVI 1.0 compliant, HDCP compatible,
for single link only
525i(480i)*
750(720)50p, 1125(1080)/60i, 1125(1080)/50i, 1125(1080)/25p,
1125(1080)/24p, 1125(1080)/24sF, 1125(1080)/30p, 1125(1080)/60p,
1125(1080)/50p
VGA (640 × 480) – WUXGA*
NOTE: Compatible with non-interlaced signals only.
BNC ×5
R: 0.7 Vp-p, 75 ohms,
G: 0.7 Vp-p (G: 1.0 Vp-p for sync on G), 75 ohms,
B: 0.7 Vp-p, 75 ohms
HD, VD/SYNC: TTL, high impedance, positive/negative automatic
NOTE: SYNC/HD and VD terminals do not accept tri-level sync signals.
Y: 1.0 Vp-p (including sync signal), PB/PR (CB/CR): 0.7 Vp-p, 75 ohms
Y: 1.0 Vp-p, C: 0.286 Vp-p, 75 ohms
D-sub HD 15-pin (female) ×1
R: 0.7 Vp-p, 75 ohms,
G: 0.7 Vp-p (G: 1.0 Vp-p for sync on G), 75 ohms,
B: 0.7 Vp-p, 75 ohms
HD, VD/SYNC: TTL, high impedance, positive/negative automatic
NOTE: SYNC/HD and VD terminals do not accept tri-level sync signals.
Y: 1.0 Vp-p (including sync signal), PB/PR(CB/CR): 0.7 Vp-p, 75 ohms
BNC × 1, 1.0 Vp-p, 75 ohms
BNC × 1, 1.0 Vp-p, 75 ohms
Input: TTL, high impedance. Output: TTL, max. 10 mA
BNC × 1, 1.0 Vp-p, 75 ohms, TTL, max. 10 mA
D-sub 9-pin (female) ×1 for external control (RS-232C compliant)
D-sub 9-pin (male) ×1 for link control
M3 jack ×1 for wired remote control
M3 jack ×1 for link control
D-sub 9-pin ×1 for external control (parallel)
RJ-45 ×1 for network connection, 100Base-TX/10Base-T, compliant
with PJLink™ (class 1)
3.0 m (9
Molded plastic
530 × 200*
(20-7/8 × 7-7/8*
24 kg (52.9 lbs) (without lens)
45 dB (high mode), 43 dB (middle mode), 37 dB (eco mode)
0°– 45°C (32°–113°F)*
10%–80% (no condensation)
3
, 625i(576i)*3, 525p(480p), 625p(576p), 750(720)/60p,
4
(1,920 × 1,200),
dot clock: 25 MHz–162 MHz
(RS-232C compliant)
10 in)
5
× 548.5 mm
5
× 21-19/32 inches) (without lens)
7
Remote control unit
Power supply
Operation range*
8
Dimensions (W × H × D)
Weight
Supplied accessories
As of April 2013
SFD12M022
3 V DC (AA/R6 type battery × 2)
Approx. 30 m (98 ft 5 in) when operated from directly in front of the
signal receptor
51 × 176 × 28 mm (2 × 6-15/16 × 1-3/32 inches)
Approx. 134 g (4.7 oz) (including batteries)
Power cord (×1) (x2 for PT-DW11KE)
Wireless/wired remote control unit (× 1)
Batteries for remote control (AA/R6 type × 2)
Lens drop-prevention screw (× 1)
Softwar
e CD-ROM (Logo Transfer Software, Multi Projector Monitoring
& Control Software) (× 1)
3/18
S PEC F ILE
3-Chip DLP™Projector
PT-DW11K
Optional accessories
Zoom lens (1.0 –1.2:1)
Zoom lens (1.4 –1.9:1)
Zoom lens (1.8 –2.7:1)
Zoom lens (2.7 –5.2:1)
Zoom lens (5.1 –8.2:1)
Zoom lens (8.2 –15.4:1)
Fixed-focus lens (0.8:1)
Lens motor cover
Ceiling mount bracket
ET-D75LE6
ET-D75LE10
ET-D75LE20
ET-D75LE30
ET-D75LE40
ET-D75LE8
ET-D75LE50
ET-D75MC1
ET-PKD310H (for high ceilings)
ET-PKD310S (for low ceilings)
Attachment for ceiling mount bracket ET-PAD310
Frame
Smoke cut filter
ET
-PFD310
ET
-SFD320
Replacement smoke cut filter ET-SFR320
Replacement lamp unit
ET-LAD310A (one bulb)
ET-LAD310AW (a set of two bulbs)
Replacement lamp unit for portrait mode
ET-LAD320P (one bulb)
ET-LAD320PW (a set of two bulbs)
Replacement filter unit
Weights and dimensions shown are approximate. Specifications and appearance are subject to change without notice.
1 When the standby mode is set to eco, network functions such as power on over the LAN network will not operate, and the serial output termi-
*
nal cannot be used. Also, only certain commands can be received for external control using the serial terminal.
2 Measurement, measuring conditions, and method of notation all comply with ISO 21118 international standards.
*
3 Only compatible with dot clock frequency of 27 MHz (pixel repetition signal)
*
4 WUXGA resolution is supported only when the signals are compliant with VESA CVT-RB (Coordinated Video Timing-Reduced Blanking).
*
5 With legs at shortest position.
*
6 Average value (excluding the optional lens). May differ depending on models.
*
*7 The operating temperature range is 0 °C to 40 °C (32 °F to 104 °F) when the FAN CONTROL is set to HIGH ALTITUDE MODE (for altitudes from
1,400 m to 2,700 m (4,593 ft to 8,858 ft) above sea level). When the projector is used with the ET-SFD320 Smoke Cut Filter, the operating temperature
range is 0 °C to 35 °C (32 °F to 95 °F), and the projector cannot be used in places at high altitude. The operating temperature range is 0 °C to 40 °C
(32 °F to 104 °F) when the ET-LAD320P/LAD320PW lamp is mounted and the projector is used in portrait configuration. The operating temperature
range is 0 °C to 35 °C (32 °F to 95 °F) when the FAN CONTROL is set to HIGH ALTITUDE MODE (for altitudes from 1,400 m to 2,700 m (4,593 ft to
8,858 ft) above sea level). When the projector is used with the ET-SFD320 Smoke Cut Filter, the operating temperature range is 0 °C to 30 °C (32 °F
to 86 °F).
*8 Operation range differs depending on environments.
ET-EMF320
As of April 2013
SFD12M022
4/18
S PEC F ILE
3-Chip DLP™Projector
Dimensions
540 (21-1/4)
548.5 (21-19/32)
8.5
(11/32)
unit : mm (inch)
NOTE: This illustration is not drawn to scale.
100
200 (7-7/8)
462 (18-3/16) 468 (18-7/16)
530 (20-7/8)
(3-15/16)
26
(1-1/32)
PT-DW11K
Terminals
1 Remote 1 input
2 Remote 1 output
3 Remote 2 input
4Serial i nput
5Serial output
6HDMI i nput
7 RGB 1 input
8 RGB 2 Input
9 DVI-D i nput
10 Video input
11 3D sync 1 input/output
12 3D sync 2 output
13 LAN connector
As of April 2013
SFD12M022
5/18
S PEC F ILE
3-Chip DLP™Projector
Standard setting-up position
Upper edge of projected image
L
Projected image
L
H H
Lower edge of projected image
L
Projected image
1
*
(7-25/32)
100
(3-15/16)
198
φ60.5
(12-3/8)
342
(13-15/32)
100
(3-15/16)
2
*
340～420
100
100
(13-3/8–
2
*
16-17/32)
436～516
(3-15/16)
(3-15/16)
–
20-5/16)
(17-5/32
PT-DW11K
*1 When the lens protrudes to the
maximum.
212 mm (8-11/32) w ith the ET-D75LE6
125 mm (4-29/32) w ith the ET-D75LE10
121 mm (4-3/4) w ith the ET-D75LE20
121 mm (4-3/4) w ith the ET-D75LE30
124 mm (4-7/8) w ith the ET-D75LE40
254 mm (10) w ith the ET-D75LE8
203 mm (8) w ith the ET-D75LE50
*2 Adjustable in 40 mm (1-9/16) steps.
unit : mm (inch)
NOTE:
Illustrations show the projector installed
using optional ceiling mount bracket
ET-PKD310H and an optional lens.
This illustration is not drawn to scale.
Caution:
• All construction work should be done by a qualified technician.
• When mounting to the ceiling, use the special mounting bracket.
Furthermore, in order to prevent it from falling down from the ceiling, use the supplied wire on the mounting bracket.
As of April 2013
SFD12M022
6/18
Loading...