Panasonic PT-DW10000 User Manual

< 1 >

S PEC F ILE

Product Number : PT-DW10000 Product Name : 3-Chip DLP™ Projector

As of July 2007. Appearance and specifications are subject to change without notice.

S PEC F ILE

PT-DW10000

3-Chip DLP™ Projector

As of July 2007 < 2 >

Specifications

Main Unit

Power supply: North America:

Europe, Asia Power consumption: DLP™ chip: Panel size:

Display method:

Pixels: Lens: Lamp: Screen size:

Brightness*

Center-to-corner uniformity*

Contrast *

Resolution:

Scanning frequency: RGB:

BPR (YCBCR):

S-Video/Video:

Optical axis shift*: Vertical:

Horizontal: Keystone correction range: Installation: Terminals: DVI-D IN:

RGB1 IN:

Y, P

B, PR

R, G, B:

RGB2 IN:

Y, P

B, PR

R, G, B:

VIDEO IN:

VIDEO OUT:

S-VIDEO IN:

LAN:

SERIAL IN *

SERIAL OUT *

: REMOTE 1 IN: REMOTE 1 OUT: REMOTE 2 IN:

120 V AC, 20 A, 60 Hz 220–240 V AC, 15 A, 50/60 Hz 1,450 W (25 W in standby mode with fan stopped)

0.95˝ diagonal (16:9 aspect ratio) DLP™ device x 3 (R, G, B), DLP™ projection system 2,073,600 (1,920 x 1,080) x 3, total of 6,220,800 pixels Optional powered zoom/focus lenses 250 W UHM™ lamp x 4 70 – 600 inches, 16:9 aspect ratio (70 – 300 inches with the ET-D75LE5, 16:9 aspect ratio) 10,000 lumens (four-lamp operation mode) 90% 5,000:1 (full on/full off, in dynamic iris 3 mode) 1,920 x 1,080 pixels (Input signals that exceed this resolution will be converted to 1,920 x 1,080 pixels.) Horizontal: 15 –100 kHz, Vertical: 24 – 120 Hz*

, Dot clock: 20–162 MHz 480i: f

H 15.75 kHz; fV 60 Hz, 576i: fH 15.63 kHz; fV 50 Hz,

480p: f

H 31.50 kHz; fV 60 Hz, 576p: fH 31.25 kHz; fV 50 Hz,

720/60p: f

H 45.00 kHz; fV 60 Hz, 720/50p: fH 37.5 kHz; fV 50 Hz,

1035/60i: f

H 33.75 kHz; fV 60 Hz, 1080/60i: fH 33.75 kHz; fV 60 Hz,

1080/50i: f

H 28.13 kHz; fV 50 Hz, 1080/25p: fH 28.13 kHz; fV 25 Hz,

1080/24p: f

H 27.00 kHz; fV 24 Hz, 1080/24sF: fH 27 kHz; fV 48 Hz,

1080/30p: f

H 33.75 kHz; fV 30 Hz, 1080/60p: fH 67.5 kHz; fV 60 Hz,

1080/50p: f

H 56.25 kHz; fV 50 Hz

Horizontal: 15.75/15.63 kHz, Vertical: 50/60 Hz, (NTSC, NTSC4.43, PAL, PAL60, PAL-N, PAL-M, SECAM) ±50% (±40° with the ET-D75LE6) from center of screen, powered ±30% (±20° with the ET-D75LE6) from center of screen, powered Vertical: ±40° (±22° with the ET-D75LE5, ±28° wih the ET-D75LE6) Ceiling/floor, front/rear DVI-D 24-pin x 1, DVI 1.0 compliant, HDCP compatible, single link BNC x 5 Y: 1.0 p-p, 75 ohms (incl. sync signal), P

B/PR: 0.7 Vp-p, 75 ohms

0.7 Vp-p (1.0 Vp-p for sync on G), 75 ohms HD/SYNC: 1.4–5 Vp-p, positive/negative automatic, 75 ohms VD: 1.4–5 Vp-p, positive/negative automatic, 75 ohms

NOTE: HD/SYNC, and VD terminals do not accept 3-value direct sync signals.

D-sub HD 15-pin x 1 Y: 1.0 p-p, 75 ohms (incl. sync signal), P

B/PR: 0.7 Vp-p, 75 ohms

0.7 Vp-p (1.0 Vp-p for sync on G), 75 ohms HD/VD/SYNC: TTL, high impedance, positive/negative automatic VD: 1.4–5 Vp-p, positive/negative automatic, 75 ohms

NOTE: HD/SYNC, and VD terminals do not accept 3-value direct sync signals.

BNC x 1, 1.0 Vp-p BNC x 1, 1.0 Vp-p, active through Mini DIN 4-pin x 1 Y: 1.0 Vp-p, C: 0.286 Vp-p, 75 ohms (S1 signal compatible) RJ-45 x 1, 10Base-T/100Base-TX, compatible with PJLink™ (class 1) D-sub 9-pin x 2 (RS-232C compliant, RS-422 compliant) D-sub 9-pin x 1 (RS-422 compliant) M3 jack x 1 for wired remote control M3 jack x 1 for link control D-sub 9-pin x 1 for external control (parallel)

S PEC F ILE

PT-DW10000

3-Chip DLP™ Projector

As of July 2007 < 3 >

Optional board slot *

With ET-MD77SD1 installed: SERIAL IN:

SERIAL OUT:

With ET-MD77SD3 installed: SERIAL IN:

SERIAL OUT:

With ET-MD77SD4 installed: Link A/Link B IN:

With ET-MD77DV installed: DVI-D IN:

Power cord: Cabinet material: Dimensions (W x H x D): Weight: Operating temperature*

Operating humidity:

Remote Control Unit

Number of functions: Power supply: Operation range*

: Dimensions (W x H x D): Weight:

Optional Accessories

Zoom lens (0.9 – 1.1:1): Zoom lens (1.4 – 1.8:1): Zoom lens (1.8 – 2.8:1): Zoom lens (2.8 – 4.6:1): Zoom lens (4.6 – 7.4:1): Zoom lens (7.3 – 13.8:1): Fixed-focus lens (0.7:1): SD-SDI/network board: HD-SDI/SD-SDI/network board: DVI-D/network board: Replacement lamp unit

Ceiling mount bracket for high ceilings Ceiling mount bracket for low ceilings Frame Carrying handle

BNC x 1, SD-SDI signal (4:2:2), SMPTE 259M compliant, 480i, 576i BNC x 1, active through BNC x 1 SD-SDI signal (4:2:2): SMPTE 259M compliant, 480i, 576i Single-link HD-SDI signal (YC

BCR 4:2:2 10-bit): SMPTE 292M com-

piant, 720/50p, 720/60p, 1080/50i, 1080/60i, 1080/25p, 1080/24p,

1080/24sF, 1080/30p BNC x 1, active through BNC x 1 for each Single-link HD-SDI signal (YC

BCR 4:2:2 10-bit): SMPTE 292M com-

piant, 720/50p, 720/60p, 1080/50i, 1080/60i, 1080/25p, 1080/24p,

1080/24sF, 1080/30p Dual-link HD-SDI signal (RGB 4:4:4 12-bit/10-bit): SMPTE 372M com-

piant, 1920 x 1080/24p, 1920 x 1080/24sF Dual-link HD-SDI signal (X´Y´Z´ 4:4:4 12-bit): 2048 x 1080/24p, 2048 x

1080/24sF DVI-D 24-pin x 1, DVI 1.0 compliant, compatible with HDCP, single link EDID1: 480p, 576p, 1080/60i, 1080/50i, 1080/24p, 1080/24sF, 1080/25p, 1080/30p, 1080/60p, 1080/50p, 720/60p, 720/50p EDID2: Compatible with non-interlaced signals only, VGA (640 x 480) – U-XGA (1,600 x 1,200), dot clock: 25–162 MHz

NOTE: LAN terminals on the optional board can not be used. Use the LAN terminal

on the projector.

3 m/9.8´ Moulded plastic 578 x 320 x 643 mm (22-3/4˝ x 12-19/32˝ x 25-5/16˝) (without lens) 32 kg (70.5 lbs) or less (without lens) 0°–45°C (32°–113°F) 10%–80% (no condensation)

35 keys, 39 functions 3 V DC (AA battery x 2) Approx. 30 m when operated from directly signal receptor 51 x 22.7 x 176 mm (2˝ x 7/8˝ x 6-15/16˝) 134 g (4.7 oz) (including batteries)

ET-D75LE6 ET-D75LE1 ET-D75LE2 ET-D75LE3 ET-D75LE4 ET-D75LE8 ET-D75LE5 ET-MD77SD1 ET-MD77SD3 ET-MD77DV ET-LAD10000 (one unit) ET-LAD10000F (a set of four lamps) ET-PKD100H ET-PKD100S ET-PFD100 ET-HAD100

Weights and dimensions shown are approximate. Specifications subject to change without notice. *1 Values indicate overall average values of the product at the time of shipment and are stated based on JIS X 6911:2003 Data Projector

Specification Sheet Format. Measurement method and conditions are based on Appendix 2. *2 Smooth image reproduction may not be possible when a motion video signal with a vertical frequency other than 50 or 60 Hz is input. *3 Shift range is limited during simultaneous horizontal and vertical shifting. *4 Contact your dealers for details when the control using RS-232C or RS-422 is required. *5 The LAN terminal on the optional board will be inactivated after installation. Use the LAN terminal on the main unit. *6 Operating temperature is 0°C– 40°C (32°F–104°F) when the fan control is set to “HIGHLAND” (for over 1,400 m to 2,700 m above sea level). *7 Operation range differs depending on environments.

S PEC F ILE

PT-DW10000

3-Chip DLP™ Projector

As of July 2007 < 4 >

Shape of the plug receptacle

Note: Be sure to use the power plug adaptor cord supplied with the projector.

The supplied power plug adaptor can be used with the PT-DW10000 only.

AC 120V AC, 20 A AC 220-240V AC, 16 A AC 220-240V AC, 13 A/15 A

Dimensions

Terminals

448 (17-5/8˝)

(4-23/32˝)

120

477

(18-25/32˝)

265 (10-7/16˝)

320 (12-19/32˝)

(1-13/32˝)

607

(23-29/32˝)

643 (25-5/16˝)

578 (22-3/4˝)

unit : mm (inch)

NOTE: This illustration is not drawn to scale.

1 Remote 1 input/output 2 Remote 2 input 3 Serial input (RS-232C) 4 Serial input (RS-422) 5 Serial output (RS-422) 6 LAN connector

(10Base-T/100Base-TX) 7 Video input 8 Video output 9 S-Video input 10 RGB 1 (YPBPR) input 11 RGB 2 Input 12 DVI-D input 13 Optional board slot

12 3 4 56

78 9 10 11 1213

+ 7 hidden pages