Panasonic PT-DS20K2U User Manual
S PEC F ILE
SFD15M027
Product Number :
Product Name :
PT-DS20K2
3-Chip DLP™ Projector
As of August 2015. Specifications and appearance are subject to change without notice.
1/13
PT-DS20K2
3-Chip DLP™ Projector
SFD15M027
Specications
Main unit
Power supply
Power consumption
DLP™ chip Panel size
Lens
Lamp
Screen size
Brightness*
Center-to-corner uniformity*
Contrast*
2
Resolution
Scanning frequency SDI
200–240 V AC, 12 A, 50/60 Hz (3-wire single-phase)
2,060 W (2,100 VA) (0.3 W with
STANDBY MODE
set to
NORMAL
.),
STANDBYMODE
set to
max. 7,031 BTU (without light output: 6,758 BTU )
24.1 mm (0.95 inches) diagonal (4:3 aspect ratio)
Display method
Pixels
DLP™ chip ×3 (R, G, B), DLP™ projection system
1,470,000 (1,400 ×1,050) ×3, total of 4,410,000 pixels
Optional powered zoom/focus lenses
432 W UHM lamps (× 4) (four lamp system)
1.78–25.4 m (70–1,000 inches) (1.78–15.24 m (70–600 inches) with
the ET-D75LE8), 4:3 aspect ratio
2
2
20,000 lumens (four lamp)
90%
10,000:1 (full on/full off, in dynamic iris 3 mode)
1,400 ×1,050 pixels (Input signals that exceed this resolution will be
converted to 1,400 × 1,050 pixels.)
Dual-link HD-SDI signal (RGB 4:4:4 12-bit/10-bit):
SMPTE ST 372 compliant: 1080/50i, 1080/60i, 1080/25p, 1080/24p,
1080/24sF, 1080/30p, 2048 x 1080/24p, 2048/1080/24sF
Dual-link HD-SDI signal (X
Y Z 4:4:4 12-bit):
SMPTE ST 372 compliant: 2048 ×1080/24p, 2048 ×1080/24sF,
3G-SDI signal (RGB 4:4:4 12-bit/10-bit):
SMPTE ST 424 compliant: 1080/50i, 1080/60i, 1080/25p, 1080/24p,
1080/24sF, 1080/30p,
3G-SDI signal (YPBPR4:2:2 10-bit):
SMPTE ST 424 compliant: 1080/50p, 1080/60p,
HD-SDI signal (YP
4:2:2 10-bit):
BPR
SMPTE ST 292 compliant: 720/50p, 720/60p, 1035/60i, 1080/50i,
1080/60i, 1080/25p, 1080/24p, 1080/24sF, 1080/30p,
SD-SDI signal (YC
4:2:2 10-bit):
BCR
SMPTE ST 259 compliant: 480i, 576i
HDMI/DVI-D/
DIGITAL LINK
RGB
Horizontal: 15 –100 kHz, vertical: 24 –120 Hz,
dot clock:
25–162 MHz
Horizontal: 15 –100 kHz, vertical: 24 –120 Hz,
dot clock: 162 MHz or less
(YCBCR)
YP
BPR
Video/S-Video
480i (525i): f
576i (625i): f
480p (525p): f
576p (625p): f
720 (750)/60p: f
720 (750)/50p: f
1035/60i: f
1080 (1125)/60i: f
1080 (1125)/50i: f
1080/25p: f
1080/24p: f
1080/24sF: f
1080/30p: f
1080/60p: f
1080/50p: f
f
: 15.73 kHz, fV: 59.94 Hz [NTSC/NTSC4.43/PA L-M/PAL60]
H
H
: 15.63 kHz, fV: 50 Hz [PAL/PAL-N/SECAM]
f
15.73 kHz; fV59.94 Hz,
H
H
15.63 kHz; fV50 Hz,
31.47 kHz; fV59.94 Hz,
H
H
31.25 kHz; fV50 Hz,
45.00 kHz; fV60 Hz,
H
37.50 kHz; fV50 Hz,
H
H
33.75 kHz; fV60 Hz,
33.75 kHz; fV60 Hz,
H
H
28.13 kHz; fV50 Hz,
28.13 kHz; fV25 Hz,
H
27.00 kHz; fV24 Hz,
H
H
27.00 kHz; fV48 Hz,
33.75 kHz; fV30 Hz,
H
H
67.50 kHz; fV60 Hz,
56.25 kHz; fV50 Hz
H
.*19Wwith
ECO
As of August 2015 2/13
PT-DS20K2
3-Chip DLP™ Projector
SFD15M027
Optical axis shiftVertical
Keystone correction range
Keystone correction range when using the
optional upgrade kit ET-UK20*
Curved correction range
Installation
Terminals SDI IN 1
±50% (±40% with the ET-D75LE6, +71% with the ET-D75LE90)
from center of screen, powered
NOTE: Optical axis shift function cannot be operated when used with the ET-D75LE50.
Horizontal
3
SDI IN 2
HDMI IN
DVI-D IN
DIGITAL LINK/LAN RJ-45 Network connection / digital link connection (video/network/serial
RGB 1 IN
R, G, B
Y, P
B, PR (Y, CB, CR)
S-Video signal
RGB 2 IN
R, G, B
, PR(Y, CB, CR)
Y, PB
3D SYNC 1 IN/OUT
3D SYNC 2 OUT
SERIAL IN
SERIAL OUT
REMOTE 1 IN
REMOTE 1 OUT
REMOTE 2 IN D-sub 9-pin (female) ×1 for external control (parallel)
±30% (±20% with the ET-D75LE6) from center of screen, powered
NOTE: Optical axis shift function cannot be operated when used with the ET-D75LE50/90.
Vertical ± 40°, horizontal ± 15°
(vertical ±22° and horizontal ±15° with the ET-D75LE50,
vertical ±28° and horizontal ±15° with the ET-D75LE6,
vertical +5° and horizontal ±15° with the ET-D75LE90)
Vertical ±45°, horizontal ±40°
(vertical ±40° and horizontal ±40° with the ET-D75LE1/2/10/20,
vertical ±28° and horizontal ±15° with the ET-D75LE6,
vertical ±22° and horizontal ±15° with the ET-D75LE5/50)
Vertical ±20°, horizontal ±15°
(vertical ±8° and horizontal ±8° with the ET-D75LE5/50,
vertical ±10° and horizontal ±10° with the ET-D75LE6)
Ceiling/oor, front/rear
BNC ×1,
Dual-link 3G-SDI signal: SMPTE ST 425 compliant (Link 1)
Dual-link HD-SDI signal: SMPTE ST 372 compliant (Link-A)
3G-SDI signal: SMPTE ST 424 compliant
HD-SDI signal: SMPTE ST 292 compliant
SD-SDI signal: SMPTE ST 259 compliant
BNC ×1,
Dual-link 3G-SDI signal: SMPTE ST 425 compliant (Link 2)
Dual-link HD-SDI signal: SMPTE ST 372 compliant (Link-B)
3G-SDI signal: SMPTE ST 424 compliant
HD-SDI signal: SMPTE ST 292 compliant
SD-SDI signal: SMPTE ST 259 compliant
HDMI 19-pin ×1, Deep Color, compatible with HDCP
DVI-D 24-pin ×1, DVI 1.0 compliant, HDCP compatible,
for single link only
control) compliant with PJLink (class1) ,100base-tx, Art-Net compatible
Deep Color, compatible with HDCP
BNC ×5
R: 0.7 Vp-p, 75 ohms,
G: 0.7 Vp-p (G: 1.0 Vp-p for sync on G), 75 ohms,
B: 0.7 Vp-p, 75 ohms
HD, VD/SYNC: TTL, high impedance, positive/negative automatic
NOTE: SYNC/HD and VD terminals do not accept tri-level sync signals.
Y: 1.0 Vp-p (including sync signal), PB/PR (CB /CR): 0.7 Vp-p, 75 ohms
Y: 1.0 Vp-p, C: 0.286 Vp-p, 75 ohms
D-sub HD 15-pin (female) ×1
R: 0.7 Vp-p, 75 ohms,
G: 0.7 Vp-p (G: 1.0 Vp-p for sync on G), 75 ohms,
B: 0.7 Vp-p, 75 ohms
HD, VD/SYNC: TTL, high impedance, positive/negative automatic
NOTE: SYNC/HD and VD terminals do not accept tri-level sync signals.
Y: 1.0 Vp-p (including sync signal), PB/PR(CB/CR): 0.7 Vp-p, 75 ohms
BNC ×1, 1.0 Vp-p, 75 ohms
Input: TTL, high impedance. Output: TTL, max. 10 mA
BNC ×1, 1.0 Vp-p, 75 ohms, TTL, max. 10 mA
D-sub 9-pin (female) ×1 for external control (RS-232C compliant)
D-sub 9-pin (male) ×1 for link control
M3 jack ×1 for wired remote control
M3 jack ×1 for link control
As of August 2015 3/13
PT-DS20K2
3-Chip DLP™ Projector
SFD15M027
Power cord length
Cabinet materials
Dimensions (W ×H × D):
6
Weight*
Operation noise*
Operating temperature
Operating humidity
Remote control unit
Power supply
Operation range*
Dimensions (W × H × D)
Weight
Supplied accessories
Optional accessories
Zoom lens (1.0–1.2:1)
Zoom lens (1.4 –1.8:1)
Zoom lens (1.8 –2.6:1)
Zoom lens (2.6 –5.1:1)
Zoom lens (5.0 –8.0:1)
Zoom lens (7.9 –15.0:1)
Fixed-focus lens (0.8:1)
Fixed-focus lens (0.39:1)
Lens motor cover
Ceiling mount bracket
Projector mount bracket ET-PKD520B
Frame
Smoke cut lter
Upgrade kit
Auto sreen adjustment upgrade kit ET-CUK10 (except in the United States)
Replacement lamp unit
Replacement lamp unit for portrait mode
Replacement lter unit
3.0 m (9
10 in)
Molded plastic
4
620 × 291*
(24-7/16×11-15/32*
×800*5mm
4
×31-1/2*5inches) (without lens)
Approx. 41 kg (90.4 lbs) (without lens)
2
46 dB (quad lamp operation)
0°– 45°C (32°–113°F)*
7
10%–80% (no condensation)
3 V DC (AA/R6type battery ×2)
8
Approx. 30 m (98
5 in) when operated from directly in front of the
signal receptor
47.5 × 181.5 × 27.5 mm (1-7/8 × 7-5/32 × 1-3/32 inches)
Approx. 150 g (5.3 oz) (including batteries)
Power cord with security lock (×1)
Wireless/wired remote control unit (× 1)
Batteries for remote control (AA/R6type ×2)
Software CD-ROM (Logo Transfer Software, Multi Projector Monitoring
& Control Software) (× 1)
ET-D75LE6
ET-D75LE10
ET-D75LE20
ET-D75LE30
ET-D75LE40
ET-D75LE8
ET-D75LE50
ET-D75LE90
ET-D75MC1
ET-PKD520H
(for high ceilings)
ET-PKD520S (for low ceilings)
ET-PFD510
ET-SFR510
ET-UK20
ET-LAD520 (one bulb)
ET-LAD520F (a set of four bulbs)
ET-LAD520P (one bulb)
ET-LAD520PF (a set of four bulbs)
ET-EMF510
Weights and dimensions shown are approximate. Specications and appearance are subject to change without notice.
1When the standby mode is set to eco, network functions such as power on over the LAN network will not operate, and the serial output termi-
*
nal cannot be used. Also, only certain commands can be received for external control using the serial terminal.
2 Measurement, measuring conditions, and method of notation all comply with ISO 21118 international standards.
*
3Up to a total of ±55° during simultaneous horizontal a nd vertical correction.
*
4 With legs at shortest position.
*
5 Excluding the optional lens.
*
6Average value (excluding the optional lens). May differ depending on models.
*
7The operating temperature range is 0 °C to 40 °C (32 °F to 104 °F) when the
*
to 2,700 m (4,593 ft to 8,858 ft) a bove sea level). When the projector is used with the ET-SFR510 Smoke Cut Filter, the operating temperature
range is 0 °C to 35 °C (32 °F to 95 °F), and the projector cannot be used in places at high altitude. The operating temperature range
40 °C (32 °F to 104 °F) when the ET- LAD520P/LAD520PF lamp is mounted and the projector is used in portrait conguration. The operating temperature range is 0 °C to 35 °C (32 °F to 95 °F) when the
to 8,858 ft) above s ea level). When the projector is used with the ET-SFR510 Smoke Cut Filter, the operating temperature range is 0 °C to 30 °C
(32 °F to 86 °F).
8 Operation range differs depending on environments.
*
FANCONTROL is set to H IGH ALTITUDE MODE (for altitudes from 1,400 m to 2,700 m (4,593 ft
FANCONTROL is set to HIGH ALTITUDE MODE (for altitudes from 1,400 m
is 0 °C to
As of August 2015 4/13
Loading...