Panasonic PT-D10000, PT-DW7000, PT-DW5000, PT-D5500, PT-D7700 User Manual
...
Panasonic Projectors RS-232C Control Specifications
D-Sub 9-pin (female),
external appearance
Serial input terminal
Pin No.
Signal name
TXD
RXD
GND
CTS
RTS
Description
NC
Send data
Receive data
Connected internally
Ground
NC
Connected internally
NC
D-Sub 9-pin (male),
external appearance
Serial output terminal
Pin No.
Signal name
RXD
TXD
GND
RTS
CTS
Description
NC
Receive data
Send data
NC
Ground
NC
Connected internally
NC
Signal level
Synchronization method
Baud rate
Parity
Character length
Stop bit
X parameter
S parameter
RS-232C-compliant
Start-stop synchronization
9 600bps
None
8 bits
1 bit
None
None
PT-D10000/DW10000 PT-D7700/DW7000 PT-D5600/DW5000 PT-D5500 PT-D3500
The main unit is equipped with SERIAL terminals located in its terminal section on the side, and this terminal is
compliant with RS-232C.
Pin assignments and signal names
Communication conditions (Factory setting)
Basic format
Transmission from the computer begins with STX, then the ID, command, parameter, and ETX are sent in this
order. Add parameters according to the details of control.
STX C1 C2 C3 : P1 P2 Pn ETXA D I 1 I 2 ;
Two ID characters
Start
(2 bytes)
ZZ, 1 to 64 and 0A to 0Z
ID designate
Semicolon
3 command
characters (3 bytes)
Colon
Parameter
(undefined length)
End
Attention
Note
No command can be sent or received for 10 to 60 seconds after the lamp starts lighting. Try
sending any command after that period has elapsed.
When sending several commands, be sure to wait for more than 0.5 seconds after receiving a
response from the projector, and then send the next command.
When sending commands without parameters, a colon (:) is not necessary.
If a wrong command is received, the projector will send an ER401 or ER402 command to the computer.
Projector ID supported on the RS-232C interface is ZZ (ALL) and a group of 1 to 64 and 0A to 0Z.
If a command is sent with a projector ID specified, the projector will return answer back only in the
following cases:
If it coincides with the projector ID,
ID specification is ALL and VPS-SYSTEM is the master, or
ID specification is group and Group is the master.
1
Control commands
Item Command:Parameter Function Call Back
POWER PON POWER ON PON YES YES YES YES
POF STANDBY(POWER OFF) POF YES YES YES YES
FREEZE OFZ:0 FREEZE OFF OFZ:0 NO YES YES YES
OFZ:1 FREEZE ON OFZ:1 NO YES YES YES
AUTO SETUP OAS AUTO SETUP OAS YES YES YES YES
SHUTTER OSH:0 SHUTTER OFF OSH:0 YES YES YES YES
OSH:1 SHUTTER ON OSH:1 YES YES YES YES
INPUT SELECT IIS:RG1 RGB-1 IIS:RG1 YES YES YES YES
IIS:RG2 RGB-2 IIS:RG2 YES YES YES YES
IIS:RG3 RGB-3 IIS:RG3 NO NO NO NO
IIS:VID VIDEO IIS:VID YES YES YES YES
IIS:SVD S-VIDEO IIS:SVD YES YES YES YES
IIS:DVI DVI IIS:DVI YES NO YES YES
IIS:AUX AUX IIS:AUX YES YES NO NO
IIS:AUX,AW1 AUX LINE(Only MD95VM2) IIS:AUX,AW1 NO YES NO NO
IIS:AUX,AW2 AUX Y/C (Only MD95VM2) IIS:AUX,AW2 NO YES NO NO
TEST OTS:00 EXIT Test Pattern OTS:00 YES YES YES YES
OTS:01 WHITE OTS:01 YES YES YES YES
OTS:02 BLACK OTS:02 YES YES YES YES
OTS:03 CHECKER1 OTS:03 YES YES YES YES
OTS:04 CHECKER2 OTS:04 YES YES NO NO
OTS:05 1% WHITE WINDOW OTS:05 YES YES YES YES
OTS:06 1% BLACK WINDOW OTS:06 YES YES YES YES
OTS:07 CROSS HATCH OTS:07 YES YES YES YES
OTS:08 COLOR BAR OTS:08 YES YES YES YES
OTS:09 RAMP OTS:09 NO NO YES YES
ON SCREEN OOS:0 OSD OFF OOS:0 YES YES YES YES
OOS:1 OSD ON OOS:1 YES YES YES YES
MUTE AMT:0 AUDIO MUTE OFF AMT:0 NO NO NO YES
AMT:1 AUDIO MUTE ON AMT:1 NO NO NO YES
D10000/DW10000
D7700/DW7000 D5600/DW5000 D3500 Remarks
D5500
Adjustment Mode
Item Command:Parameter Function Call Back
PICTURE MODE VPM:NAT NATURAL VPM:NAT YES YES YES YES
VPM:STD STANDARD VPM:STD YES YES YES YES
VPM:DYN DYNAMI VPM:DYN YES YES YES YES
VPM:CIN CINEMA VPM:CIN YES YES YES YES
VPM:GRA GRAPHIC VPM:GRA YES YES YES YES
VPM:USR USER VPM:USR YES NO NO NO
COLOR VCO:p1p2p3 COLOR Value Adjust VCO:p1p2p3 YES YES YES YES From0 To 100 *1
TINT VTN:p1p2p3 TINT Value Adjust VTN:p1p2p3 YES YES YES YES From0 To 62 *3
COLOR TEMP. OTE:0 LOW OTE:0 YES YES NO NO
OTE:1 MIDDLE OTE:1 YES YES YES YES
OTE:2 HIGH OTE:2 YES YES YES YES
OTE:3 DYNAMIC OTE:3 NO NO NO NO
OTE:4 USER (USER1) OTE:4 YES NO YES YES
OTE:5 STANDARD OTE:5 NO NO NO NO
OTE:6 NATURAL OTE:6 NO NO NO NO
OTE:7 CINEMA OTE:7 NO NO NO NO
OTE:8 GRAPHIC OTE:8 NO NO NO NO
OTE:9 USER2 OTE:9 YES YES NO NO
OTE:10 DEFAULT OTE:10 YES YES YES YES
CONTRAST VCN:p1p2p3 CONTARST Value Adjust VCN:p1p2p3 YES YES YES YES From0 To 63 *1
BRIGHTNESS VBR:p1p2p3 BRIGHTNESS Value Adjust VBR:p1p2p3 YES YES YES YES From0 To 63 *1
SHARPNESS VSR:p1p2p3 SHARPNESS Value Adjust VSR:p1p2p3 YES YES YES YES <SD> From0 To 15,
SET DATE TSD:y1y2y3y4m1m2d1d2w Set Date
SET TIME TST:h1h2m1m2s1s2 Set Time TST:h1h2m1m2s1s2 YES YES YES YES *2
VOLUME AVL:p1p2p3 AUDIO VOLUME AVL:p1p2p3 NO NO NO YES
*1: Regarding p1p2p3, +1,+01,+001,1,01,001 are All Accepted *2: Date/Time Should be set on UTC (Coordinate Universal Time) *3: Only use of PT-D10000 and PT-DW10000
TSD:y1y2y3y4m1m2d1d2w
D10000/DW10000
YES YES YES YES
NO NO NO YES
D7700/DW7000 D5600/DW5000 D3500 Remarks
D5500
<HD,RGB>From0 To 7 *1
y1y2y3y4m1m2d1d2+Date of Week
Mon=1,Tue=2,
...
,Sun=7 *2
2
Status Asking Comman
Item Command:Parameter Function Call Back
POWER CONDITION
FREEZE QFZ Freeze Function Status 0 NO YES YES YES OFF
SHUTTER QSH Shutter Status 0 YES YES YES YES OFF
INPUT SIGNAL QIN Input Signal Status RG1 YES YES YES YES RGB1
TEST QTS Test Pattern Status 00 YES YES YES YES
02 YES YES YES YES BLACK
ON SCREEN QOS ON SCREEN Status 0 YES YES YES YES off
PICTURE MODE QPM PICTURE MODE Status NAT YES YES YES YES NATURAL
USR YES NO NO NO USER
COLOR QVC COLOR Adjust Value Check p1p2p3 YES YES YES YES
TINT QVT TINT Adjust Value Check p1p2p3 YES YES YES YES
COLOR TEMP. QTE COLOR TEMP Status Check 0 YES YES NO NO LOW
CONTRAST QVR
BRIGHTNESS QVB BRIGHTNES Adjust Value p1p2p3 YES YES YES YES
SHARPNESS QVS SHARPNESS Adjust Value p1p2p3 YES YES YES YES
SET RUNTIME QST Set Run Time CHeck p1p2p3p4p5 YES YES YES YES 00000h~99999h
LAMP ON TIME Q$L:1 LAMP1 Run Time Check p1p2p3p4 YES YES YES YES 0000h~9999h
LAMP SELECT QSL Lamp Operation Mode Check 0 YES YES NO DUAL
QPW Main Power Status 000 YES YES YES YES STANDBY(OFF)
001 YES YES YES YES ON
1 NO YES YES YES ON
1 YES YES YES YES ON
RG2 YES YES YES YES RGB2
RG3 NO NO NO NO RGB3
VID YES YES YES YES VIDEO
SVD YES YES YES YES S-VIDEO
DVI YES NO YES YES DVI
AUX YES YES NO NO AUX
QIN:AW AUX,AW1 NO YES NO NO AUX LINE
QIN:AW AUX,AW2 NO YES NO NO AUX Y/C
01 YES YES YES YES WHITE
03 YES YES YES YES CHECKER1
04 YES YES NO NO CHECKER2
05 YES YES YES YES
06 YES YES YES YES
07 NO YES YES YES CROSS HATCH
08 YES YES YES YES COLOR BAR
09 NO NO YES YES RAMP
1 YES YES YES YES on
STD YES YES YES YES STANDARD
DYN YES YES YES YES DYNAMIC
CIN YES YES YES YES CINEMA
GRA YES YES YES YES GRAPHIC
1 YES YES YES YES MIDDLE
2 YES YES YES YES HIGH
3 NO NO NO NO DYNAMIC
4 YES YES YES YES USER (USER1)
5 NO NO NO NO STANDARD
6 NO NO NO NO NATURAL
7 NO NO NO NO CINEMA
8 NO NO NO NO NATURAL
9 YES YES NO NO USER2
10 YES YES YES YES DEFAULT
CONTARST Adjust Value Checking
Q$L:2 LAMP2 Run Time Check p1p2p3p4 YES YES YES NO
Q$L:3 LAMP3 Run Time Check p1p2p3p4 YES NO NO NO
Q$L:4 LAMP4 Run Time Check p1p2p3p4 YES NO NO NO
p1p2p3 YES YES YES YES
1 YES YES NO SINGLE
2 YES YES NO LAMP1
3 YES YES NO LAMP2
D10000/DW10000
D7700/DW7000 D5600/DW5000 D3500 Meaning Remarks
D5500
EXIT Test Pattern
1% WHITE WINDOW
1% BLACK WINDOW
MD95VM2
MD95VM2
3
LAMP SELECT QSL Lamp Operation Mode Check 0 YES NO NO NO QUAD (4 lamp)
(D10000/DW10000)
1 YES NO NO NO L1/L4
2 YES NO NO NO L2/L3
3 YES NO NO NO DUAL (2 lamp)
4 YES NO NO NO L1/L2/L3
5 YES NO NO NO L1/L2/L4
6 YES NO NO NO L1/L3/L4
7 YES NO NO NO L2/L3/L4
8 YES NO NO NO TRIPLE (3 lamp)
9 YES NO NO NO L1
10 YES NO NO NO L2
11 YES NO NO NO L3
12 YES NO NO NO L4
13 YES NO NO NO SINGLE
LAMP POWER QLP LAMP POWER Mode Check 0 NO YES YES YES HIGH
1 NO YES YES YES LOW
2 NO TBD YES YES (RESERVED)
VPS SYSTEM QVY VPS SYSTEM Check 0 YES YES YES NO SLAVE
1 YES YES YES NO MASTER
INPUT BOARD QIB
Check the type of Input Board
p1p2p3p
............
NO YES NO NO MD95VM2
(Voluntary length) YES YES NO NO MD95SD1
NO YES NO NO MD95SD2
YES YES NO NO MD95SD3
NO YES NO NO MD95RGB
NO YES NO NO MD75NT
YES YES NO NO MD75DV
YES YES NO NO MD77SD1
YES YES NO NO MD77SD3
YES YES NO NO MD77DV
YES YES NO NO NONE No board
Unknown board
Unsupported board
TEMP CHECK QTM:0
Check the status of Temperature
YES YES NO NO UNKNOWN
YES YES NO NO NOT SUPPORT
p1p2p3p4/p5p6p7p8 YES YES YES YES INPUT AIR
QTM:1 Sensor (Celsius/ Fahrenheit) YES YES NO NO OUTPUT AIR
QTM:2 YES YES YES YES
GET DATE QGD Check the Day
y1y2y3y4m1m2d1d2w
YES YES YES YES
OPTICAL MODULE
Yyyymmdd (day of the week)
Mon=1,Tur=2,
GET TIME QGT Check the Time h1h2m1m2s1s2 YES YES YES YES hhmmss UTC
MUTE QAM Audio Mute Status 0 NO NO NO YES MUTE OFF
1 NO NO NO YES MUTE ON
VOLUME QAV Volume Status p1p2p3 NO NO NO YES
...
,Sun=7
4
Loading...