Page 1
Sunshield for POH INSTRUCTION MANUAL
Installation
Instruction
Before attempting to connect or operate this product,
please read these instructions completely.
1
Page 2
Sunshield for POH INSTRUCTION MANUAL
!
WARNING
This service information is designed for experienced repair technicians and is not designed fro use by
the general public.
It does not contain warnings or cautions to advise nontechnical individuals of potential dangers in
attempting to service a product.
Products powered by electricity should be serviced or repaired only by experienced professional
technicians. Any attempt to service or repair this product or products dealt with in this service
information by anyone else could result in serious injury or death.
CAUTION
RISK OF ELECTRICAL SHOCK
DO NOT OPEN
CAUTION:
TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK). NO USER
SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
!
!
This symbol warns the user that uninsulated voltage within
the unit may have sufficient magnitude to cause electric
shock. Therefore, it is dangerous to make any kind of
contact with any inside part of this unit.
This symbol warns the user that important literature
concerning the operation and maintenance of this unit has
been included. Therefore, it should be read carefully in
order to avoid any problems.
IMPORTANT SAFETY NOTICE
There are special components used in this equipment which are important for safety. These parts are
indicated by the mark on the schematic and the replacement parts list. It is essential that these
!
critical parts should be replaced with manufacturer’s specified parts to prevent shock, fire, or other
hazards.
Do not modify the original design without permission of manufacturer.
CAUTION
This must be properly and securely mounted to a supporting structure capable of sustaining the weight of the bracket and
camera assembly. Accordingly,
1. The installation should be made by a qualified installer.
2. The installation should be in compliance with local codes.
3. Care should be exercised to select suitable hardware to install the unit, taking into account both the composition of
the mounting surface and the weight the hardware willbe required to sustain.
Be sure to periodically examine the unit and the supporting structure to make sure that the integrity of the installation is intact.
Failure to comply with the foregoing could result in the unit coming loose from the support structure and falling, with resultant
damages or injury to anyone or anything struck by the falling unit.
2
Page 3
Sunshield for POH INSTRUCTION MANUAL
1. PRECAUTIONS ON INSTALLATIONS
• Installation should be in accordance with all applicable local and National Electric codes. Only approve materials should be
utilized.
• This unit must be properly and securely mounted to a supporting structure that is capable of sustaining the weight of the
housing.
• Read instruction completely before installation and operation.
Standard Accessories (supplied)
1 pc. Sunshield
1 pc. 6-32 x 5/8 screw
1 pc. Locknut
Installation for PSS10 and PSS15
1. Align inside legs of the sunshield with the top grooves of the POH top extrusion.
2. Slide legs into grooves and push sunshield onto the housing until the ends of both parts are flush and
the access holes on the sunsheild are aligned with the screws on the top extrusion of the POH.
NOTE: It may be necessary to slightly bend open the end of the sunshield to
help start the inside legs sliding into the grooves.
NOTE: Sunshield may be installed from the front or the rear of the housing.
3. After sliding the sunshield onto the housing make sure the hole on the rear of the sunsheild and the
hole on the rear of the housing top are aligned.
4. Take the 6-32x5/8" Truss phillips head screw and insert it into the hole in the rear of the sunshield
and through the POH top extrusion. Secure the screw with the locknut.
NOTE: Do not over tighten the nut to the point to where the sunshield begins to bow in the center.
3
Page 4
Sunshield for POH INSTRUCTION MANUAL
Inside Leg
Insert in hole
Align to first groove
Rear View
of Housing
5.77"
13.25"
PSS10
5.77"
18.25"
2.13"
2.13"
PSS15
4
Rev. 3023/0897
Loading...