Panasonic NV-GS150EG, NV-GS150EP, NV-GS150GC, NV-GS150GN, NV-GS150GCD Service Manual
...
© 2005 Matsushita Electric Industrial Co., Ltd. All
rights reserved. Unauthorized copying and
distribution is a violation of law.
NV-GS150E
NV-GS150EG
NV-GS150EB
NV-GS150EP
NV-GS150GC
NV-GS150GN
NV-GS150GCD
NV-GS140E
NV-GS140EG
NV-GS140EB
NV-GS140EP
NV-GS158GK
VOL.1
A-MECHANISM
Colour
(S)....................Silver Type
Digital Video Camera / Recorder
ORDER NO.VM0502004C8
Downloaded From VideoCamera-Manual.com Manuals
2
NV-GS150E / NV-GS150EG / NV-GS150EB / NV-GS150EP / NV-GS150GC / NV-GS150GN / NV-GS150GCD / NV-GS140E / NV-GS140EG / NV-GS140EB / NV-GS140EP / NV-GS158GK
Downloaded From VideoCamera-Manual.com Manuals
1 Service Information Regarding Simultaneous Exchange of
MONITOR C.B.A. and LCD PANEL UNIT of NV-GS150, GS140
and GS158
4
1.1. Overview
4
1.2. How to Distinguish the Types of MONITOR C.B.A. and
LCD PANEL UNIT.
4
1.3. Difference Comparison Chart
5
1.4. Attention for exchange the MONITOR C.B.A..
5
1.5. Attention for exchange the LCD PANEL UNIT.
5
2 INTRODUCTION
6
2.1. INTRODUCTION
6
2.2. ABOUT LEAD FREE SOLDER (PbF)
7
3 CAUTION FOR AC CORD (VJA0940 TYPE)
8
3.1. INFORMATION FOR YOUR SAFETY
8
3.2. CAUTION FOR AC MAINS LEAD
8
4 HOW TO REPLACE THE LITHIUM BATTERY (PROCEDURE)
9
5 ADJUSTMENT PROCEDURES
10
5.1. DISASSEMBLE FLOW CHART
10
5.2. DISASSEMBLY PROCEDURES
11
5.3. DISASSEMBLY PROCEDURES MECHA. UNIT
18
5.4. DISASSEMBLY PROCEDURES OF CAMERA LENS UNIT
22
6 SERVICE CAUTION
23
6.1. HOW TO DISCHARGE THE CAPACITOR ON FRONT
C.B.A.
23
6.2. EEPROM DATA FOR SPARE PARTS OF THE MAIN
C.B.A.
23
6.3. SERVICE EXTENSION CABLES.
23
6.4. LOCATION FOR CONNECTORS OF THE MAIN C.B.A. &
SUB C.B.A.
25
7 ELECTRICAL ADJUSTMENT PROCEDURES
27
7.1. COMPUTER ASSISTED ADJUSTMENT SYSTEM <
TATSUJIN > ADJUSTMENT.
27
7.2. SET-UP MANUAL FOR DV-Camcorder.
27
7.3. SET UP PC-EVR ADJUSTMENT PROGRAM
30
7.4. INITIAL GUIDELINE
31
8 MECHANICAL ADJUSTMENT PROCEDURES
32
8.1. ADJUSTMENT ITEM
32
8.2. ADJUSTMENT PROCEDURES
32
9 SERVICE MODE
34
9.1. ERROR DISPLAY
34
9.2. SERVICE MENU
35
10 WAVEFORM TABLE
36
11 SCHEMATIC DIAGRAM
37
11.1. OVERALL SCHEMATIC DIAGRAM
37
11.2. INTERCONNECTION SCHEMATIC DIAGRAM
38
11.3. SIDE (L) FLEX. CARD / CASSETTE COVER
SCHEMATIC DIAGRAM
40
11.4. LCD HINGE (MONITOR FLEX.) SCHEMATIC DIAGRAM
40
11.5. REAR OPERATION UNIT SCHEMATIC DIAGRAM
40
11.6. EVF SCHEMATIC DIAGRAM
40
11.7. CCD FLEX. CARD SCHEMATIC DIAGRAM
41
11.8. FRONT SCHEMATIC DIAGRAM
42
11.9. JACK SCHEMATIC DIAGRAM
43
11.10. SIDE (R) / LCD DET. SCHEMATIC DIAGRAM
44
11.11. MONITOR SCHEMATIC DIAGRAM
45
12 CIRCUIT BOARD ASSEMBLIES
47
12.1. EVF C.B.A.
47
12.2. LCD DET. C.B.A.
47
12.3. SIDE (R) C.B.A.
47
12.4. CCD FLEX. CARD C.B.A.
48
12.5. FRONT C.B.A.
49
12.6. JACK C.B.A.
50
12.7. MONITOR C.B.A.
51
13 EXPLODE D VIEWS
53
13.1. FRAME & CASING SECTION (1)
53
13.2. FRAME & CASING SECTION (2)
54
13.3. LCD SECTION
55
13.4. CAMERA LENS SECTION
56
13.5. VCR MECHANISM SECTION
57
13.6. PACKING PARTS & ACCESSORIES SECTION
58
14 REPLACEMENT PARTS LIST
59
14.1. FRAME & CASING SECTION (1) PARTS LIST
59
14.2. FRAME & CASING SECTION (2) PARTS LIST
59
14.3. LCD SECTION PARTS LIST
60
14.4. CAMERA LENS SECTION PARTS LIST
60
14.5. VCR MECHANISM SECTION PARTS LIST
60
14.6. PACKING PARTS & ACCESSORIES SECTION PARTS
LIST
60
14.7. ELECTRICAL REPLACEMENT PARTS LIST
61
CONTENTS
Page Page
3
NV-GS150E / NV-GS150EG / NV-GS150EB / NV-GS150EP / NV-GS150GC / NV-GS150GN / NV-GS150GCD / NV-GS140E / NV-GS140EG / NV-GS140EB / NV-GS140EP / NV-GS158GK
Downloaded From VideoCamera-Manual.com Manuals
1 Service Information Regarding Simultaneous Exchange
of MONITOR C.B.A. and LCD PANEL UNIT of NV-GS150,
GS140 and GS158
1.1. Overview
· DVCmodel NV-GS150, GS140 and GS158 will be manufactured 4 distinctly different MONITOR C.B.A. and 2 distinctlydifferent
LCD PANEL UNIT.
· These 4 version of MONITOR C.B.A. will be referred to as C.B.A. type “A”, “B”, “C” and “D”.
· These 2 version of LCD PANEL UNIT will be referred to as UNIT type “A” and “B”.
· There are not the exchangeability between the “A”, “B”, “C” and “D” of MONITOR C.B.A..
· There are not the exchangeability between the “A” and “B” of LCD PANEL UNIT.
· MONITOR C.B.A. and LCD PANEL UNIT supply it the kit.
(Do not supply it in one of each individually MONITOR C.B.A. and LCD PANEL UNIT.)
1.2. How to Distinguish the Types of MONITOR C.B.A. and LCD PANEL
UNIT.
4
NV-GS150E / NV-GS150EG / NV-GS150EB / NV-GS150EP / NV-GS150GC / NV-GS150GN / NV-GS150GCD / NV-GS140E / NV-GS140EG / NV-GS140EB / NV-GS140EP / NV-GS158GK
Downloaded From VideoCamera-Manual.com Manuals
1.3. Difference Comparison Chart
1.4. Attention for exchange the MONITOR C.B.A..
· In the case that the LCD PANEL UNIT is TYPE “A”.
Replace the chip resistor of R901 and R910 to the chip resistor that is doing the same pack to the kit.
R901 ERJ3RBD182 → ERJ3GEY0R00
R910 ERJ3RBD822 → ERJ3RBD682
· In the case that the LCD PANEL UNIT is TYPE “B”.
Exchange only the MONITOR C.B.A..
1.5. Attention for exchange the LCD PANEL UNIT.
· In the case that the MONITOR C.B.A. is TYPE “A” and “B”.
Replace the chip resistor of R901 and R910 to the chip resistor that is doing the same pack to the kit.
R901 ERJ3RBD182 → ERJ3GEY0R00
R910 ERJ3RBD822 → ERJ3RBD682
· In the case that the MONITOR C.B.A. is TYPE “C” and “D”.
Exchange only the LCD PANEL UNIT.
CAUTION:
It does the confirmation of the MONITOR C.B.A. and LCD PANEL UNIT without fail on the occasion of the repair and please
do the part exchange.
5
NV-GS150E / NV-GS150EG / NV-GS150EB / NV-GS150EP / NV-GS150GC / NV-GS150GN / NV-GS150GCD / NV-GS140E / NV-GS140EG / NV-GS140EB / NV-GS140EP / NV-GS158GK
Downloaded From VideoCamera-Manual.com Manuals
2 INTRODUCTION
2.1. INTRODUCTION
This service manual contains technical information which will allow service personnel´s to understand and service this
model.Please place orders using the parts list and not the drawing reference numbers.
If the circuit is changed or modified, this information will be followed by supplement service manual to be filed with original service
manual.
Note 1:
These movie camera uses AC Adaptor VSK0651A or VSK0651B.
Note 2:
1) This service manual does not contain the following information, because of the impossibility of sevicing at component level.
1. Schematic Diagram, Block Diagram and C.B.A. layout of Main C.B.A./ Sub C.B.A.
2. Parts List for individual parts of Main C.B.A./ Sub C.B.A.
2) The following category is/are recycle module part. Please send it/them to Central Repair Center.
*Main C.B.A. (VEP03G73B: NV-GS150E/EG/EB/EP, VEP03G73C: NV-GS150GC/GN/GCD,
VEP03G73G: NV-GS140 SERIES,VEP03G73D: NV-GS158GK)
*Sub C.B.A. (VEP23612B: NV-GS150 SERIES, NV-GS140 SERIES, NV-GS158GK)
When a part replacement is required for repairing each Main C.B.A., replace the assembly parts.
(Main C.B.A. and Sub C.B.A.)
The following circuits are contained in Main C.B.A.
1. Main Connection Circuit
2. AVIO Circuit
3. Video Circuit
4. Power Circuit
5. Control Circuit
The following circuits are contained in Sub C.B.A.
1. Sub Connection Circuit
2. LCD Circuit
3. Lens Drive Circuit
4. Sub Power Circuit
5. Camera Circuit
6
NV-GS150E / NV-GS150EG / NV-GS150EB / NV-GS150EP / NV-GS150GC / NV-GS150GN / NV-GS150GCD / NV-GS140E / NV-GS140EG / NV-GS140EB / NV-GS140EP / NV-GS158GK
Downloaded From VideoCamera-Manual.com Manuals
2.2. ABOUT LEAD FREE SOLDER (PbF)
7
NV-GS150E / NV-GS150EG / NV-GS150EB / NV-GS150EP / NV-GS150GC / NV-GS150GN / NV-GS150GCD / NV-GS140E / NV-GS140EG / NV-GS140EB / NV-GS140EP / NV-GS158GK
Downloaded From VideoCamera-Manual.com Manuals
3 CAUTION FOR AC CORD
(VJA0940 TYPE)
3.1. INFORMATION FOR YOUR
SAFETY
IMPORTANT
Your attention is drawn to the fact that recording of prerecorded tapes or discs or other published or broadcast
material may infringe copyright laws.
WARNING
To reduce the risk of fire or shock hazard, do not expose
this equipment to rain or moisture.
CAUTION
To reduce the risk of fire or shock hazard and annoying
interference, use the recommended accessories only.
FOR YOUR SAFETY
DO NOT REMOVE THE OUTER COVER
To prevent electric shock, do not remove the cover. No user
serviceable parts inside. Refer servicing to qualified service
personnel.
3.2. CAUTION FOR AC MAINS
LEAD
For your safety, please read the following text carefully.
This appliance is supplied with a moulded three-pin mains plug
for your safety and convenience.
A 5-ampere fuse is fitted in this plug.
Should the fuse need to be replaced please ensure that the
replacement fuse has a rating of 5 amperes and it is approved
by ASTA or BSI to BS1362
Check for the ASRA mark or the BSI mark on the body of the
fuse.
If the plug contains a removable fuse cover you must ensure
that it is refitted when the fuse is replaced.
If you lose the fuse cover, the plug must not be used until a
replacement cover is obtained.
A replacement fuse cover can be purchased from your local
Panasonic Dealer.
If the fitted moulded plug is unsuitable for the socket outlet in
your home then the fuse should be removed and the plug cut
off and disposed of safety.
There is a danger of severe electrical shock if the cut off plug
is inserted into any 13-ampere socket.
If a new plug is to be fitted please observe the wiring code as
shown below.
If in any doubt, please consult a qualified electrician.
3.2.1. Important
The wires in this mains lead are coloured in accordance with
the following code:
Blue Neutral
Brown Live
As the colours of the wires in the mains lead of this appliance
may not correspond with the coloured markings identifying the
terminals in your plug, proceed as follows:
The wire which is coloured BLUE must be connected to the
terminal in the plug which is marked with the letter N or
coloured BLACK.
The wire which is coloured BROWN must be connected to the
terminal in the plug which is marked with the letter L or coloured
RED.
Under no circumstances should either of these wires be
connected to the earth terminal of the three pin plug, marked
with the letter E or the Earth Symbol.
3.2.2. Before use
remove the Connector Cover as follows.
3.2.3. How to replace the Fuse
1. Remove the Fuse Cover with a screwdriver.
2. Replace the fuse and attach the Fuse cover.
8
NV-GS150E / NV-GS150EG / NV-GS150EB / NV-GS150EP / NV-GS150GC / NV-GS150GN / NV-GS150GCD / NV-GS140E / NV-GS140EG / NV-GS140EB / NV-GS140EP / NV-GS158GK
Downloaded From VideoCamera-Manual.com Manuals
4 HOW TO REPLACE THE LITHIUM BATTERY
(PROCEDURE)
1. Remove the Side Case (L) C.B.A.. (Refer to Disassembly Procedures.)
2. Unsolder the Lithium Battery “ML-621S/F9D” and then replace the new one. (See Fig. B1.)
3. Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.
Fig. B1
Note:
The lithium battery is a critical component. (Type No.: N9ZZ00000288.)
It must never be subjected to excessive heat or discharge.
It must therefore only be fitted in equipment designed specifically for its use.
Replacement batteries must be of the same type and manufacture.
They must be fitted in the same manner and location as the original battery, with the correct polarity contacts observed.
Do not attempt to re-charge the old battery or re-use it for any other purpose.
It should be disposed of in waste products destined for burial rather than incineration.
9
NV-GS150E / NV-GS150EG / NV-GS150EB / NV-GS150EP / NV-GS150GC / NV-GS150GN / NV-GS150GCD / NV-GS140E / NV-GS140EG / NV-GS140EB / NV-GS140EP / NV-GS158GK
Downloaded From VideoCamera-Manual.com Manuals
5 ADJUSTMENT PROCEDURES
5.1. DISASSEMBLE FLOW CHART
This flow chart indicates the disassembly steps the cabinet parts, C.B.A. and Mecha. Unit in order to access to be serviced. When
reinstalling, perform the steps in the reverse order.
Fig. F1
10
NV-GS150E / NV-GS150EG / NV-GS150EB / NV-GS150EP / NV-GS150GC / NV-GS150GN / NV-GS150GCD / NV-GS140E / NV-GS140EG / NV-GS140EB / NV-GS140EP / NV-GS158GK
Downloaded From VideoCamera-Manual.com Manuals
5.2. DISASSEMBLY PROCEDURES
Flow-Chart for Disassembly Procedure
No. Item / Part Fig. Removal (Screw,Connector,Flex. &
Other)
1 Front Case
Unit
Fig. D2 Remove the Grip Belt Piece with the
procedure of arrow 1,2,3.
Fig. D3 1-Screw (A)
Fig. D4 Open the LCD Unit
1-Screw (B), 2-Screws (C)
Fig. D5 1-Connector FP4801
Front Case Unit
2 Side Case (R)
Unit
Fig. D6 2-Screws (D)
Fig. D7 2-Screws (E), 1-Screw (F)
Fig. D8 2-Connectors FP602, FP6503
Side Case (R) Unit
3 Lens Unit Fig. D9 1-Screw (G)
2-Connectors FP201, FP701
Lens Unit
4 EVF/Rear
Operation
Unit,.Sub
C.B.A
Fig. D10 1-Screw (H), 2-Screws (I), 1-Screw (J)
4-Connectors FP601, FP1001,
FP3402, FP6502
EVF/Rear Operation Unit
2-Connectors FP304, PS3001
Sub C.B.A.
5 Main C.B.A. Fig. D11 8-Connectors FP2201, FP2202,
FP2203, FP2204, FP5001,
FP6501,FP6504, FP6505
1-Screw (K)
4-Tabs
Main C.B.A.
6 Mecha. Unit Fig. D12 Open the Cassette Cover
3-Screws (L)
Mecha. Unit
7 Jack C.B.A. Fig. D13 1-Screw (M), 1-Screw (N), 1-Screw (O)
Jack C.B.A.
8 Front C.B.A. Fig. D14 5-Screws (P)
3-Tabs
Front C.B.A.
9 Monitor C.B.A. Fig. D15 1-Screw (Q), 3-Screws (R)
Rear Cover
Fig. D16 Turning the LCD Unit
2-Screws (S)
LCD Unit
Fig. D17 2-Screws (T)
6-Tabs
LCD Case (Upper) Unit
Fig. D18 1-Connector FP902
LCD Hinge Unit
Fig. D19 1-Connector FP901
2-Tabs
Monitor C.B.A.
10 EVF C.B.A. Fig. D20 View ADJ. Unit is Drawn
1-Screw (U)
Rear Operation Unit
Fig. D21 1-Screw (V)
2-Tabs
EVF Hold Piece
Fig. D22 2-Screws (W)
2-Tabs
View ADJ. Unit
2-Screws (X), 2-Slide Spacers (Y)
1-Connector FP801
EVF LCD Unit
Fig. D23 2-Screws (Z)
EVF Plate / Click Spring
Fig. D24 1-Connector FP802
3-Tabs
EVF C.B.A.
Fig. D1
Fig. D2
11
NV-GS150E / NV-GS150EG / NV-GS150EB / NV-GS150EP / NV-GS150GC / NV-GS150GN / NV-GS150GCD / NV-GS140E / NV-GS140EG / NV-GS140EB / NV-GS140EP / NV-GS158GK
Downloaded From VideoCamera-Manual.com Manuals
Fig. D3
Fig. D4
Fig. D5
Fig. D6
12
NV-GS150E / NV-GS150EG / NV-GS150EB / NV-GS150EP / NV-GS150GC / NV-GS150GN / NV-GS150GCD / NV-GS140E / NV-GS140EG / NV-GS140EB / NV-GS140EP / NV-GS158GK
Downloaded From VideoCamera-Manual.com Manuals
Fig. D7
Fig. D8
Fig. D9
Fig. D10
13
NV-GS150E / NV-GS150EG / NV-GS150EB / NV-GS150EP / NV-GS150GC / NV-GS150GN / NV-GS150GCD / NV-GS140E / NV-GS140EG / NV-GS140EB / NV-GS140EP / NV-GS158GK
Downloaded From VideoCamera-Manual.com Manuals
Fig. D11
Fig. D12
Fig. D13
14
NV-GS150E / NV-GS150EG / NV-GS150EB / NV-GS150EP / NV-GS150GC / NV-GS150GN / NV-GS150GCD / NV-GS140E / NV-GS140EG / NV-GS140EB / NV-GS140EP / NV-GS158GK
Downloaded From VideoCamera-Manual.com Manuals
Fig. D14
Fig. D15
Fig. D16
15
NV-GS150E / NV-GS150EG / NV-GS150EB / NV-GS150EP / NV-GS150GC / NV-GS150GN / NV-GS150GCD / NV-GS140E / NV-GS140EG / NV-GS140EB / NV-GS140EP / NV-GS158GK
Downloaded From VideoCamera-Manual.com Manuals
Fig. D17
Fig. D18
Fig. D19
Fig. D20
16
NV-GS150E / NV-GS150EG / NV-GS150EB / NV-GS150EP / NV-GS150GC / NV-GS150GN / NV-GS150GCD / NV-GS140E / NV-GS140EG / NV-GS140EB / NV-GS140EP / NV-GS158GK
Downloaded From VideoCamera-Manual.com Manuals
Fig. D21
Fig. D22
Fig. D23
Fig. D24
17
NV-GS150E / NV-GS150EG / NV-GS150EB / NV-GS150EP / NV-GS150GC / NV-GS150GN / NV-GS150GCD / NV-GS140E / NV-GS140EG / NV-GS140EB / NV-GS140EP / NV-GS158GK
Downloaded From VideoCamera-Manual.com Manuals
5.3. DISASSEMBLY PROCEDURES MECHA. UNIT
Flow-Chart for Disasswmbly Procedures
No. Item / Part Fig. Removal (Screw, Connector, Flex. & Other)
1 Cassette Up Unit Fig. M1 It makes the mechanism position in Eject condition (For Battery)
Fig. M2 3-Screws (A)
Fig. M3 3-Tabs
I remove the piece arrangement unit from rail department
2 Cylinder Unit Fig. M4 1-Screw (B)
Fig. M5 3-Screw (C)
Cylinder Unit
Fig. M1
Fig. M2
18
NV-GS150E / NV-GS150EG / NV-GS150EB / NV-GS150EP / NV-GS150GC / NV-GS150GN / NV-GS150GCD / NV-GS140E / NV-GS140EG / NV-GS140EB / NV-GS140EP / NV-GS158GK
Downloaded From VideoCamera-Manual.com Manuals
Fig. M3
19
NV-GS150E / NV-GS150EG / NV-GS150EB / NV-GS150EP / NV-GS150GC / NV-GS150GN / NV-GS150GCD / NV-GS140E / NV-GS140EG / NV-GS140EB / NV-GS140EP / NV-GS158GK
Downloaded From VideoCamera-Manual.com Manuals
Fig. M4
Fig. M5
20
NV-GS150E / NV-GS150EG / NV-GS150EB / NV-GS150EP / NV-GS150GC / NV-GS150GN / NV-GS150GCD / NV-GS140E / NV-GS140EG / NV-GS140EB / NV-GS140EP / NV-GS158GK
Downloaded From VideoCamera-Manual.com Manuals
Loading...