Before use, please read these instructions completely.
VQT9154
Dear Customer,
Before Use
We would like to take this opportunity to thank you for purchasing this Panasonic Movie Camera.
Please read these Operating Instructions carefully and keep them handy for future reference.
Please note that the actual controls and components, menu items, etc. of your Movie Camera may
look somewhat different from those shown in the illustrations in these Operating Instructions.
Information for Your Safety
Movie Camera
≥The rating plate is on the underside of the Movie
Camera.
AC Adaptor
≥The rating plate is on the underside of the AC Adaptor.
≥As this equipment gets hot during use, operate it in
well ventilated place; do not install this equipment in a
confined space such as a bookcase or similar unit.
Caution for AC mains lead
For your safety, please read the following text carefully.
This appliance is supplied with a moulded three-pin
mains plug for your safety and convenience. A 5-ampere
fuse is fitted in this plug.
Should the fuse need to be replaced, please ensure that
the replacement fuse has a rating of 5-amperes and it is
approved by ASTA or BSI to BS1362.
Check for the ASTA mark Ï or the BSI mark Ì on the
body of the fuse.
If the plug contains a removable fuse cover you must
ensure that it is refitted when the fuse is replaced. If you
lose the fuse cover, the plug must not be used until a
replacement cover is obtained. A replacement fuse
cover can be purchased from your local Panasonic
Dealer.
IF THE FITTED MOULDED PLUG IS UNSUITABLE
FOR THE SOCKET OUTLET IN YOUR HOME THEN
THE FUSE SHOULD BE REMOVED AND THE PLUG
CUT OFF AND DISPOSED OF SAFELY.
THERE IS A DANGER OF SEVERE ELECTRICAL
SHOCK IF THE CUT OFF PLUG IS INSERTED INTO
ANY 13-AMPERE SOCKET.
If a new plug is to be fitted, please observe the wiring
code as shown below.
If in any doubt, please consult a qualified electrician.
ª IMPORTANT
The wires in this mains lead are coloured in accordance
with the following code:
Blue:Neutral
Brown:Live
As the colours of the wires in the mains lead of this
appliance may not correspond with the coloured
markings identifying the terminals in your plug, proceed
as follows:
The wire which is coloured BLUE must be connected to
the terminal in the plug which is marked with the letter N
or coloured BLACK.
The wire which is coloured BROWN must be connected
to the terminal in the plug which is marked with the letter
L or coloured RED.
Under no circumstances should either of these wires be
connected to the earth terminal of the three-pin plug,
marked with the letter E or the Earth Symbol Ó.
ª Before Use
Remove the Connector
Cover as follows.
ª How to replace the
Fuse
1) Remove the Fuse Cover
with a screwdriver.
2) Replace the fuse and
attach the Fuse Cover.
Connector
Cover
Fuse
Cover
Fuse
Operating Instructions
≥These Operating Instructions apply to models NV-DS27,
NV-DS28, NV-DS37 and NV-DS38.
≥The illustrations used in these Operating Instructions show
model NV-DS38, however, parts of the explanation refer to
different models.
≥Depending on the model, some functions are not available.
≥SD Logo is a trademark.
≥All other company and product names in the operating
instructions are trademarks of their respective
corporations.
Still pictures recorded on a MultiMediaCard or SD
Memory Card (NV-DS37/DS38 only)
It may not be possible to play back the pictures on this Movie
Camera recorded on and created by other equipment or vice
versa. For this reason, check the compatibility of the
equipment in advance.
2
Pages for reference
Pages for reference are indicated with an arrow, for example:
(l 00)
ª WARNING
To reduce the risk of fire or shock hazard and annoying
interference, use only the recommended accessories
and do not expose this equipment to rain or moisture.
Do not remove the cover (or back); there are no user
serviceable parts inside. Refer servicing to qualified
service personnel.
ª Carefully observe copyright laws.
Recording of pre-recorded tapes or discs or other
published or broadcast material for purposes other than
your own private use may infringe copyright laws. Even
for the purpose of private use, recording of certain
material may be restricted.
Contents
Before Use
Information for Your Safety ................................................. 2
≥“TitleStudio,” software for title creation, and “SD-Jukebox,” software for
recording music are included. (However, this Movie Camera cannot play
back music.)
23) MultiMediaCard (VW-MMC8E/VW-MMC16E)
24) Floppy Disk Adaptor for MultiMediaCard (VW-MAF1E)
25) SD Memory Card (RP-SD016/RP-SD032/RP-SD064)
26) PC Card Adaptor for SD Memory Card (BN-SDABPE)
27) USB Reader Writer for SD Memory Card (BN-SDCAPE)
≥Some optional accessories may not be available in some countries.
9)
VFF0079K1V208A10002
≥Order accessory and consumable items for all Audio Visual Products with
ease and confidence either by telephoning our Customer Care Centre on
08705 357357 Mon–Friday 9:00am–5:30pm
≥Or go on line through our Internet Accessory ordering application at
www.panasonic.co.uk.
≥Most major credit and debit cards accepted.
≥All enquires transactions and distribution facilities are provided directly by
Panasonic UK Ltd.
≥It couldn’t be simpler!
4
Getting Started
Charge the Battery. (l
1
1
≥Connect the Battery to the AC Adaptor.
≥Connecting the AC Mains Lead. (Charging starts.)
≥When the Charge Lamp [CHARGE] goes off, the Battery is fully
charged.
10)
2
3
<
EJECT
1
3
2
PUSH
LOCK
4
CAMERA
VCR
CARD
P.B
MODE
OFF ON
Attach the Charged Battery to the Movie Camera. (l
2
Insert the Cassette. ( l
3
≥Slide the
Lever to open.
1
11)
≥Insert the Cassette.
≥Press the
Turn the Movie Camera on and start recording. (l
4
≥Set the
≥Press the
≥Press the
Button to close the Cover.
2
Switch to [ON]. (The [CAMERA] Lamp lights up.)
3
Button. (Recording starts.)
4
Button again to pause the recording.
4
10)
12, 18)
4
3
5, 6
S
s
SEARCHFADE STILLBLC
r
56º1;
678
CAMERA
VCR
CARD
MODE
P.B
OFF ON
5
9
Viewing What Has Been Recorded
Switch to the VCR Mode, rewind the tape, and play the tape
5
back.
≥Press the 5 Button. (The [VCR] Lamp lights up.)
≥Press the
≥Press the
≥Press the
“THE LITHIUM BATTERY IS A CRITICAL COMPONENT (TYPE NUMBER
CR2025 MANUFACTURED BY PANASONIC).
IT MUST NEVER BE SUBJECTED TO EXCESSIVE HEAT OR DISCHARGE.
IT MUST THEREFORE ONLY BE FITTED IN EQUIPMENT DESIGNED
SPECIFICALLY FOR ITS USE.
REPLACEMENT BATTERIES MUST BE OF THE SAME TYPE AND
MANUFACTURER.
THEY MUST BE FITTED IN THE SAME MANNER AND LOCATION AS THE
ORIGINAL BATTERY, WITH THE CORRECT POLARITY CONNECTIONS
OBSERVED.
DO NOT ATTEMPT TO RE-CHARGE THE OLD BATTERY OR RE-USE IT
FOR ANY OTHER PURPOSE. IT SHOULD BE DISPOSED OF IN WASTE
PRODUCTS DESTINED FOR BURIAL RATHER THAN INCINERATION.”
Direct the Remote Controller to the Remote Control Sensor
of the Movie Camera and press an appropriate button.
≥Distance from the Movie Camera:Within approximately 5 metres
≥Angle:Within approximately 15o in the vertical and horizontal directions
from the central axis
1
15˚
15˚
15˚
15˚
START/
PHOTO
DATE/
OSD
TIME
RESET
COUNTER
MULTI/
¥REC
P-IN-P
V
/REW
PLAY
615
STILL ADV
PAUSE
ED
INDEXINDEX
STOP
21
KL
SELECT
SEARCH
STORE
OFF/ON
P.B.DIGITAL
STOP
SHOT
TITLE
ZOOM
T
A.DUB
sVOLr
W
FF/
W
STILL ADV
;
∫
VAR.
MENU
ITEM
P.B.
ZOOM
SET
≥The above operating ranges are for indoor use. Outdoors or under strong
light, the Movie Camera may not operate properly even within the above
ranges.
≥Within a 1-metre range, you can also use the Remote Controller on the side
(the [MENU] Button side) of the Movie Camera.
Selecting Remote Controller Modes
When 2 Movie Cameras are used simultaneously, they can be operated
individually by selecting different Remote Controller Modes.
≥If the Remote Controller Mode of the Movie Camera and that of the Remote
Controller do not match, [REMOTE] Indication is displayed.
Setup on the Movie Camera:
Set [REMOTE] on the [OTHER FUNCTIONS] Sub-Menu to the desired
Remote Controller Mode. (l 13)
Setup on the Remote Controller:
[VCR1]:Press the [D] Button and [∫] Button simultaneously.
[VCR2]:Press the [E] Button and [∫] Button simultaneously.
≥When the battery in the Remote Controller is replaced, the mode is
automatically reset to [VCR1] Mode.
1
2
9
Power Supply
ª Using the AC Adaptor
1
Connect the DC Input Lead to the [DC IN] Socket on the
Movie Camera.
Connect the DC Input Lead to the AC Adaptor.
2
Connect the AC Mains Lead to the AC Adaptor and the AC
1
3
mains socket.
≥The AC Mains Lead’s outlet plug cannot be pushed fully into the AC
Adaptor socket. A gap will remain as shown
≥Before disconnecting the power supply, set the [OFF/ON] Switch on the
Movie Camera to [OFF].
1
.
1
2
3
1
2
CGR-D08R
CGR-D08S
CGP-D14S
CGP-D210
CGR-D16S
CGR-D220
CGP-D28S
CGP-D320
CGR-D53S
CGR-D815
PUSH
3
NV-DS27/DS28NV-DS37/DS38
A
B
C
CGR-D120
A
B
C
A
B
C
A
B
C
A
B
C
1 h.
1 h 50 min. (1 h 30 min.)
55 min. (45 min.)
1 h 50 min.
3 h 10 min. (2 h 40 min.)
1 h 35 min. (1 h 20 min.)
2 h.
4 h. (3 h 15 min.)
2 h. (1 h 40 min.)
3 h 15 min.
7 h. (5 h 40 min.)
3 h 30 min. (2 h 50 min.)
5 h 20 min.
13 h. (10 h 25 min.)
6 h 30 min. (5 h 15 min.)
1 h 40 min. (1 h 25 min.)
2 h 55 min. (2 h 30 min.)
1 h 30 min. (1 h 15 min.)
1 h 45 min. (1 h 30 min.)
6 h 5 min. (5 h 15 min.)
3 h 5 min. (2 h 40 min.)
50 min. (45 min.)
3 h 30 min. (3 h.)
11 h 25 min. (10 h.)
5 h 45 min. (5 h.)
2
ONOFF
1 h.
1 h 50 min.
2 h.
3 h 15 min.
5 h 20 min.
ª Using the Battery
Before use, fully charge the Battery.
Attach the Battery to AC Adaptor and charge it.
1
≥Since the Battery will not be charged when the DC Input Lead is
connected to the AC Adaptor, disconnect them.
≥The [POWER] Lamp and [CHARGE] Lamp lights up, and charging
starts.
≥When the [CHARGE] Lamp goes off, charging is completed.
Attach the charged Battery to the Movie Camera.
2
To Remove the Battery
Set the [OFF/ON] Switch 2 to [OFF], and while pressing the [PUSH] Button
, slide the Battery to remove it.
3
ª Using the Car Battery Charger
If you use the Car Battery Charger (VW-KBD2E; optional), you can supply
power to the Movie Camera and charge the battery inside your car. For
further information, refer to the instruction manual of the Car Battery Charger.
≥Be sure to start the car engine before you connect the Car Adaptor Cord,
otherwise the fuse may blow.
≥For other notes concerning this item, see page 39.
~~~~~~~~~~~~~~~~~~~~~~~~
Charging Time and Available Recording Time
Charging Time
A
Maximum Continuous Recording Time
B
Intermittent Recording Time
C
(Intermittent Recording Time is the available recording time with repeated
recording and stopping actions.)
≥“1h10min.” indicates 1 hour and 10 minutes.
≥Battery CGR-D08R is supplied.
≥The times shown in the table are approximate times. The numbers in
parentheses indicate the recording time when the LCD Monitor is used.In
actual use, the available recording time may be shorter.
≥The times shown in the table are for continuous recording at a temperature
of 20oC and humidity of 60%. If the Battery is charged at a higher or lower
temperature, the charging time may be longer.
10
Lens Cap and Grip Belt
To protect the Lens surface, attach the Lens Cap. Adjust the length of the
1
2
Grip Belt to the size of your hand.
1
Attach the Lens Cap to the Grip Belt.
2
Put your hand through the Grip Belt and adjust the length.
≥The removed Lens Cap can be hooked onto the Grip Belt 1.(When you are
not recording, be sure to keep the Lens Cap attached to the Lens for
protection.)
1
~~~~~~~~~~~~~~~~~~~~~~~~~
Attaching the Shoulder Strap
1
We recommend that you attach the Shoulder Strap before going out of doors
to record so as to avoid dropping the Movie Camera.
1
Pull the end of the Shoulder Strap through the Shoulder
Strap Holder on the Movie Camera.
2
Fold the tip of the Shoulder Strap, run it through the
Shoulder Strap Length Adjuster, and pull it.
≥Pull it out more than 2 cm 1 from the Shoulder Strap Length Adjuster
so that it cannot slip off.
2
1
~~~~~~~~~~~~~~~~~~~~~~~~~
2
<
EJECT
1
3
1
R E C
SAVE
PUSH
LOCK
3
Inserting a Cassette
When power is supplied to the Movie Camera, the Cassette can be taken out
without turning the Movie Camera [ON].
1
Slide the [<EJECT] Lever to open the Cover.
2
Insert a Cassette.
3
Close the Cover and press the [PUSH LOCK] Button to lock
the Cover.
ªAccidental Erasure Prevention
Opening the accidental erasure prevention slider 1 on the cassette (by
sliding it in the [SAVE] arrow direction) prevents recording. To enable
recording, close the accidental erasure prevention slider (by sliding it in the
[REC] arrow direction).
≥For other notes concerning this item, see page 39.
11
CAMERA
VCR
CARD
P.B
MODE
OFF ON
2
1, 3
12:30:45
12:30:45
12:30:45
15.10.2001
15.10.2001
15.10.2001
12:30:45
15.10.2001
1
1
1
23
180
2
PRESSMENUTORETURN
x
LCD/EVFSET
LCDBRIGHTNESS
[-]||||----[+]
LCDCOLOURLEVEL
[-]||||----[+]
EVFBRIGHTNESS
[-]||||----[+]
90
x
Turning on the Movie Camera and Selecting
Modes
Turn on the power first and then select modes.
ªHow to Turn on the Power
1
Set the [OFF/ON] Switch to [ON].
≥The [CAMERA] Lamp lights up.
ªHow to Switch Modes
2
Press the [MODE] Button.
≥With each press, the Mode changes.
≥The appropriate Mode Lamp lights up.
ªHow to Turn off the Power
3
Set the [OFF/ON] Switch to [OFF].
~~~~~~~~~~~~~~~~~~~~~~~~
Using the Viewfinder/LCD Monitor
ªUsing the Viewfinder
Before using the Viewfinder, adjust the field of view so that the displays inside
the Viewfinder become clear and easy to read.
1
2
Tilt the Viewfinder upward.
≥The Viewfinder can also be pulled out for use.
≥Do not pull on the Eyecup to extend the Viewfinder.
2
Adjust by sliding the Eyepiece Corrector Knob 1.
ªUsing the LCD Monitor
With the LCD Monitor open, you can also record the picture while watching it.
Press the [PUSH OPEN] Button and, at the same time, bring
1111
the LCD Monitor out about 90o in the direction of the arrow.
≥The Viewfinder goes off.
Adjust the LCD Monitor angle according to the desired
2222
recording angle.
≥The LCD Monitor can rotate a maximum of 180o2 from the vertical
position to the upward direction and a maximum of 90o
downward direction. Forcefully rotating the LCD Monitor beyond these
ranges will damage the Movie Camera.
Closing the LCD Monitor
Push the LCD Monitor until the [PUSH OPEN] Button is securely locked.
3
to the
ªAdjusting Brightness and Colour Level
When [LCD/EVF SET] on the [DISPLAY SETUP] Sub-Menu is set to [YES],
the following items are displayed. (l 13)
LCD Brightness [LCD BRIGHTNESS]
It adjusts the brightness of the image on the LCD screen.
LCD Colour Level [LCD COLOUR LEVEL]
It adjusts the colour saturation of the image on the LCD screen.
Brightness of the Viewfinder [EVF BRIGHTNESS]
It adjusts the brightness of the image in the Viewfinder.
To A djus t
Press the [PUSH] Dial and select the item to be adjusted, and then turn the
[PUSH] Dial to raise or lower the number of vertical bars in the Bar Indication.
≥A larger number of vertical bars indicates stronger brightness or colour
saturation.
Increasing the Brightness of the Entire LCD Monitor
Set the [LCD MODE] on the [DISPLAY SETUP] Sub-Menu to [BRIGHT].
≥These adjustments do not affect the recorded images.
12
≥For other notes concerning this item, see page 45.
AUTO
MNL
M
FOCUS
W
E
A
.
G
S
/
B
.
M
O
R
P
MENU
Using the Menu Screen
To facilitate the selection of a desired function or setup, this Movie Camera
displays various function setups on Menus.
1
Press the [MENU] Button.
CAMERA
VCR
CARD
P.B
MODE
1
T
T
E
U
R
H
/
I
R
I
S
2, 3,
PUSH
G
F
O
/
J
V
/
L
O
4, 5
1
≥The Menu corresponding to the Mode selected using by the [MODE]
Button
2
Turn the [PUSH] Dial to select a desired Sub-Menu.
is displayed.
1
≥Turn the [PUSH] Dial to display the highlightened item.
3
Press the [PUSH] Dial to display the selected Sub-Menu.
4
Turn the [PUSH] Dial to select the item to be set.
5
Press the [PUSH] Dial to set the selected item to a desired
mode.
≥With each pressing of the [PUSH] Dial, the cursor [ 1] moves to the
next mode. Menu items that cannot be used in combination with the
selected item are displayed in dark blue.
≥While a Menu is displayed, you cannot record or play back. Menus can be
displayed during playback but not during recording. The above operations
can be done using the [MENU] Button, [SET] Button and [ITEM] Button on
the Remote Controller. (l 8)
To Exit the Menu Screen
Press the [MENU] Button again.
About the Menu Mode Setting
The setting selected on the Menu will be retained even when the Movie
Camera is turned off. However, if the Battery or AC Adaptor is disconnected
before turning off the Movie Camera, the selected setup may not be retained.
(But, the setups of [EFFECT2] (l 25) are not retained.)
≥Menu operation flow is shown in this text by >>.
AUTO
MNL
M
FOCUS
W
E
A
.
G
MENU
T
U
H
S
/
B
.
M
F
O
/
V
O
R
P
T
E
R
/
I
R
I
S
PUSH
G
O
J
/
L
PICTURE
1,2
No.25 IMGA0012.JPG
2
ªImage Selection (NV-DS37/DS38 only)
A Menu Selection Operation may be necessary during Menu Operations. In
this case, carry out the following procedure.
Turn the [PUSH] Dial and select a picture.
1111
≥The selected picture is marked by a frame 2.
Press the [PUSH] Dial to confirm the selection of the picture.
2222
≥After the above Picture Selectioin Procedure, carry out the various Menu
Operations. (The above procedure will not be repeated in the following
instructions.)
13
CAMERA FUNCTIONS
1.
CAMERA SETUP
2.
DIGITAL EFFECT
3.
CARD SETUP
4.
RECORDING SETUP
5.
DISPLAY SETUP
6.
OTHER FUNCTIONS
7.
DEMO MODE
PRESS MENU TO EXIT
1)
2)
3)
4)
5)
6)
7)
8)
PICTURE QUALITY
9)
FINE NORMAL ECONOMY
CREATE TITLE
10)
RETURN ---- YES
11)
12)
13)
14)
15)
16)
17)
18)
19)
20)
21)
22)
23)
24)
25)
26)
27)
CAMERA SETUP
PROGRESSIVE OFF ON AUTO
SIS OFF ON
D.ZOOM
CINEMA OFF ON
M.SENSOR OFF ON
RETURN ---- YES
PRESS MENU TO EXIT
EFFECT1
EFFECT2 OFF NEGA SEPIA
RETURN ---- YES
PRESS MENU TO EXIT
PRESS MENU TO EXIT
REC SPEED
AUDIO REC 12bit
SCENEINDEX 2HOUR DAY
WIND CUT OFF ON
ZOOM MIC OFF ON
RETURN ---- YES
PRESS MENU TO EXIT
DATE/TIME
C.DISPLAY COUNTER MEMORY
C.RESET ---- YES
DISPLAY ALL PARTIAL OFF
LCD MODE NORMAL BRIGHT
LCD/EVF SET ---- YES
RETURN ---- YES
PRESS MENU TO EXIT
REMOTE
REC LAMP OFF ON
BEEP SOUND OFF ON
SHTR EFFECT OFF ON
CLOCK SET ---- YES
SELFSHOOT NORMAL MIRROR
RETURN ---- YES
PRESS MENU TO EXIT
OFF 30 600
DIGITAL EFFECT
OFF WIPE MIX
STROBE GAINUP
TRACER MOSAIC
MIRROR
B/W SOLARI
CARD SETUP
RECORDING SETUP
SP LP
DISPLAY SETUP
OFF TIME DATE
TIMECODE
OTHER FUNCTIONS
VCR1 VCR2 OFF
---- YES
16bit
List of Menus
The figures of the Menus are for explanation purposes only, and they are
different from the actual Menus.
6) Returning to the Main-Menu [RETURN]
≥If you set [RETURN] to [YES], the menu changes back to the Main-
Menu.
[DIGITAL EFFECT] Sub-Menu
7) Digital Effects 1 [EFFECT1] (l 25)
8) Digital Effects 2 [EFFECT2] (l 25)
[CARD SETUP] Sub-Menu (NV-DS37/DS38 only)
9) Picture Quality [PICTURE QUALITY] (l 33)
10) Title Creation [CREATE TITLE] (l 36)
[RECORDING SETUP] Sub-Menu
11) Recording Speed Mode [REC SPEED] (l 17)
12) Audio Recording Mode [AUDIO REC] (l 17)
13) Scene Index Mode [SCENEINDEX] (l 28)
14) Wind Noise Reduction [WIND CUT] (l 22)
15) Zoom Microphone [ZOOM MIC] (l 19)
[DISPLAY SETUP] Sub-Menu
16) Date and Time Indication [DATE/TIME] (l 39)
17) Counter Display Mode [C.DISPLAY] (l 38)
18) Counter Reset [C.RESET] (l 47)
≥It resets the counter to zero. However, it cannot reset the Time Code.
19) Display Mode [DISPLAY] (l 39)
20) LCD Lighting Mode [LCD MODE] (l 12)
21) LCD and Viewfinder Adjustment [LCD/EVF SET] (l 12)
[OTHER FUNCTIONS] Sub-Menu
22) Remote Controller Mode [REMOTE] (l 9)
23) Recording Lamp [REC LAMP] (l 18)
24) Beep Sound [BEEP SOUND] (l 39)
25) Shutter Effect [SHTR EFFECT] (l 19)
26) Date and Time Setting [CLOCK SET] (l 17)
27) Self-Recording [SELFSHOOT] (l 18)
[DEMO MODE] Sub-Menu
28) Demonstration Mode [DEMO MODE]
≥If no operation takes place for approximately 10 minutes after the AC
Adaptor was connected to the Movie Camera and the [OFF/ON] Switch
was turned to [ON] without inserting a Cassette, the Movie Camera is
automatically set to Demonstration Mode for introducing its functions. If
any button is pressed or operated, the Demonstration Mode is
cancelled. The Demonstration Mode can be started by setting [DEMO
MODE] to [ON] and by exiting the Menu. To terminate the
Demonstration Mode, insert a Cassette or set the [DEMO MODE] to
[OFF].
14
DEMO MODE
28)
RETURN ---- YES
DEMO MODE
PRESS MENU TO EXIT
OFF ON
VCR FUNCTIONS
1.
PLAYBACK FUNCTIONS
2.
DIGITAL EFFECT
3.
CARD SETUP
4.
RECORDING SETUP
5.
AV IN/OUT SETUP
6.
DISPLAY SETUP
7.
OTHER FUNCTIONS
PRESS MENU TO EXIT
1)
2)
3)
4)
5)
6)
7)
8)
9)
10)
11)
PLAYBACK FUNCTIONS
BLANK SEARCH ---- YES
RECORD TO CARD ---- YES
AUTO PRINT ---- YES
SEARCH PHOTO SCENE
12bit AUDIO ST1 ST2 MIX
AUDIO OUT
RETURN ---- YES
PRESS MENU TO EXIT
DIGITAL EFFECT
EFFECT OFF ON
EFFECT SELECT
OFF WIPE MIX
STROBE NEGA SEPIA
B/W TRACER SOLARI
MOSAIC MIRROR
RETURN ---- YES
PRESS MENU TO EXIT
PICTURE QUALITY
FINE NORMAL ECONOMY
CREATE TITLE
RETURN---- YES
CARD SETUP
PRESS MENU TO EXIT
STEREO L R
---- YES
VCR Mode Main-Menu [VCR FUNCTIONS]
[PLAYBACK FUNCTIONS] Sub-Menu
1) Blank Search [BLANK SEARCH] (l 27)
2) Recording to Card [RECORD TO CARD] (NV-DS37/DS38 only) (l 33)
1) Selecting and Erasing a Picture [ERASE PICTURE BY SELECTION]
(l 37)
2) Erasing All Pictures [ERASE ALL PICTURES] (l 37)
3) Selecting and Erasing a Title [ERASE TITLE BY SELECTION] (l 37)
[CARD EDITING] Sub-Menu
4) Recording to Tape [RECORD TO TAPE] (l 34)
5) Automatic Printing [AUTO PRINT] (l 32)
6) Searching a Picture [PICTURE SEARCH] (l 34)
7) Setting the Lock [FILE LOCK] (l 37)
8) Setting a Slide Show [SLIDE SHOW] (l 35)
9) Setting DPOF [DPOF SETTING] (l 37)
10) Formatting a Card [CARD FORMAT] (l 42)
[DISPLAY SETUP] Sub-Menu
All of the items on the [DISPLAY SETUP] Sub-Menu are the same as those
on the [DISPLAY SETUP] Sub-Menu of the [CAMERA FUNCTIONS] MainMenu.
[OTHER FUNCTIONS] Sub-Menu
All of the items on the [OTHER FUNCTIONS] Sub-Menu are the same as
those on the [OTHER FUNCTIONS] Sub-Menu of the [CAMERA
FUNCTIONS] Main-Menu.
OTHER FUNCTIONS
REMOTE VCR1 VCR2 OFF
CLOCK SET ---- YES
RETURN ---- YES
PRESS MENU TO EXIT
A
11)
PICTURE SEARCH
12)
ERASE PICTURE
FILE LOCK
13)
DPOF SETTING
14)
EXIT
15)
Short-Cut Menu
s of the Card Playback Mode (NV-DS37/DS38 only)
A
If you use the Short-Cut Menu, the Card Playback Mode Menu can be called
up quickly. Press the [PUSH] Dial to display the Short-Cut Menu, and turn the
[PUSH] Dial to select the desired Menu.
11) [PICTURE SEARCH]:
The [PICTURE SEARCH] Menu for finding pictures by number appears.
(l 34)
12) [ERASE PICTURE]:
The [ERASE PICTURE] Menu for erasing the picture being displayed
appears. (l 37) Use this Menu after the picture to be erased appears.
13) [FILE LOCK]:
The [FILE LOCK] Menu for avoiding accidental erasure of pictures (Lock
Setting) being displayed appears. (l 37)Use this Menu after the picture
to be locked appears.
14) [DPOF SETTING]:
The [DPOF SETTING] Menu for setting DPOF to the picture displayed
appears. (l 37) Use this Menu after the picture for DPOF Setting
appears.
15) [EXIT]:
It is for terminating the Short-Cut Menu.
16
Loading...
+ 36 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.