Page 1
10.16. Replacement of Refrigerator
10.17. Changing The Doorway Direc-
Lamp
1. Remove the refrigerator lamp cover by pulling forward.
2. Loosen the lamp and replace it.
tion
Warning: Make sure the unit is unplugged.
1. Unscrew the screw fixing the Top Hinge Cover and
remove it.
2. Disconnect the Display Connector.
3. Unscrew the screws fixing the Top Hinge and remove it.
Note : The grounding wire is only for protecting the product (especially for display) against static electric forming
at production line.
There is no function at daily use.
64
Page 2
4. Remove the Refrigerator Door.
7. Lie down the appliance to the back. (min: 300mm)
CAUTION:Do not damage the outer condenser.
5. Unscrew the two screws which are fixing the Middle
Hinge and remove the Washer.
6. Remove the Freezer Door.
8. Unscrew the Stationary Foot under the Bottom Hinge.
9. Unscrew the Bottom Hinge fixing screws and remove it.
65
Page 3
10. Unscrew the Stationary Foot on the left side.
11. Unscrew the side panel fixing screw.
13. Screw the Stationary Foot for the right side.
14. Insert the Flat screwdriver into the gap between the
Spacer and the Bottom Hinge. Then pry off the Spacer.
Unscrew the pin of hinge, rotate the Bottom Hinge 180°.
12. Then use that screw for the right side.
NOTICE
Be careful to screw stronger. Because the screw
hole has blocked with the expanded polyurethane.
15. Screw the pin to the same hole from different direction.
Paste the Spacer to the opposite side of the Bottom
Hinge.
66
Page 4
16. Then screw the Bottom Hinge to the left side.
17. Screw the Stationary Foot for the left side.
20. Put up the appliance.
21. Detach a right Bushing, and insert it in the left hole.
22. Remove a left Bushing Cap,and insert it in the left hole.
18. Remove the Door Handle Screw Cap and Middle Hinge
Screw Caps on the left side.
19. Then insert that Door Handle Screw Cap and Middle
Hinge Screw Caps on the right side.
23. Turn the Freezer Door upside down.
24. Remove the Catcher Right of Freezer Door.
67
Page 5
25. Insert the new Catcher Left in left. (You can find the new
Catcher Left in the user manuel bag)
NOTICE
The screw hole is not open. Please drill it by an
electric drill as shown in figure.
The drill diameter should be 2.5mm.
27. Turn the Middle Hinge upside down and screw it and
Washer to the left side.
28. Remove the Catcher Right of Refrigerator Door.
26. Assemble the freezer door.
29. Install left Bushing CAP in the right hole.
68
Page 6
30. Insert the new Catcher Left in left. (You can find the new
Catcher Left in the user manuel bag)
NOTICE
The screw hole is not open. Please drill it by an
electric drill as like Freezer Door's Catcher Left.
31. Remove the Bushing Cover and pull the Cable to outside.
The Bushing Cover is used on the right side.
33. Unscrew the Hinge Pin and rotate the pin upside down
then fix it to right side of the Top Hinge.
32. Roll and insert the lead wire.
Cut the grounding wire as shown in figure and insert the
bushing cover to the left side.
34. Swap the Head Panel Covers.
69
Page 7
35. Assemble the Refrigerator Door.
36. Remove the Socket Cover and attach it on the right side.
38. Connect the Display Connector.
39. Mount the Top Hinge Cover and screw it.
37. Screw the Top Hinge fixing screws.
70
Loading...