Panasonic KX-TG6702 User Manual
TG6700.book Page 1 Tuesday, May 23, 2006 3:38 PM
Operating Instructions
5.8 GHz Expandable Digital Cordless
Answering System
Model No.
5.8 GHz Expandable Digital Cordless
Answering System with Two Handsets
Model No.
Model shown is KX-TG6700.
This unit is compatible with Caller ID. To use this feature, you must subscribe to
the appropriate service offered by your telephone service provider.
Charge the handset battery for 7 hours before initial use.
Please read these Operating Instructions before using the unit and save for
future reference.
For assistance, visit our website:
http://www.panasonic.com/phonehelp for customers in the U.S.A. or Puerto
Rico.
KX-TG6700
KX-TG6702
TG6700.book Page 2 Tuesday, May 23, 2006 3:38 PM
Table of Contents
Introduction
Introduction. . . . . . . . . . . . . . . . . . . . . . . 3
Accessory information . . . . . . . . . . . . . . 4
Important safety instructions . . . . . . . . . 6
For best performance . . . . . . . . . . . . . . . 8
Preparation
Setting up the base unit . . . . . . . . . . . . . 9
Setting up the handset . . . . . . . . . . . . . 12
Controls . . . . . . . . . . . . . . . . . . . . . . . . 15
Displays . . . . . . . . . . . . . . . . . . . . . . . . 17
Symbols used in these operating
instructions . . . . . . . . . . . . . . . . . . . . . . 18
Setting the unit before use . . . . . . . . . . 19
Making/Answering Calls
Making calls . . . . . . . . . . . . . . . . . . . . . 21
Answering calls . . . . . . . . . . . . . . . . . . 23
Useful features during a call. . . . . . . . . 24
Using the other line during a call . . . . . 27
Phonebook
Handset phonebook . . . . . . . . . . . . . . . 28
Base Unit Speed Dialer
Base unit speed dialer . . . . . . . . . . . . . 31
Remote operation . . . . . . . . . . . . . . . . . 45
Answering system settings . . . . . . . . . . 47
Multi-unit Operation
Intercom . . . . . . . . . . . . . . . . . . . . . . . . 49
Transferring calls . . . . . . . . . . . . . . . . . 50
Conference calls. . . . . . . . . . . . . . . . . . 51
Room monitor . . . . . . . . . . . . . . . . . . . . 53
Registering a handset. . . . . . . . . . . . . . 54
Useful Information
Additional accessories . . . . . . . . . . . . . 55
Error messages . . . . . . . . . . . . . . . . . . 56
Troubleshooting . . . . . . . . . . . . . . . . . . 58
FCC and other information . . . . . . . . . . 62
Specifications . . . . . . . . . . . . . . . . . . . . 65
Customer services . . . . . . . . . . . . . . . . 66
Warranty . . . . . . . . . . . . . . . . . . . . . . . . 67
Index
Index. . . . . . . . . . . . . . . . . . . . . . . . . . . 69
Caller ID Service
Using Caller ID service. . . . . . . . . . . . . 32
Caller list. . . . . . . . . . . . . . . . . . . . . . . . 33
Programming
Programmable settings . . . . . . . . . . . . 35
Answering System
Answering system . . . . . . . . . . . . . . . . 40
Listening to messages using the base
unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Listening to messages using the
handset. . . . . . . . . . . . . . . . . . . . . . . . . 43
Voice memo . . . . . . . . . . . . . . . . . . . . . 44
2 For assistance, please visit http://www.panasonic.com/phonehelp
TG6700.book Page 3 Tuesday, May 23, 2006 3:38 PM
Introduction
Introduction
Thank you for purchasing a Panasonic cordless telephone.
We recommend keeping a record of the following information for future reference.
Serial No. Date of purchase
(found on the bottom of the base unit)
Name and address of dealer
Attach your purchase receipt here.
Notable differences between KX-TG6700 and KX-TG6702
These operating instructions can be used for the following models:
KX-TG6700 features a handset.
KX-TG6702 features 2 handsets.
Important:
L References in these operating instructions to “a charger” or “other handsets” are for
accessory handset users and KX-TG6702 users only. See “Expanding your phone
system” on page 5.
KX-TG6700 KX-TG6702
2 handsets
For assistance, please visit http://www.panasonic.com/phonehelp 3
TG6700.book Page 4 Tuesday, May 23, 2006 3:38 PM
Introduction
Accessory information
Included accessories
No. Accessory item Order number
1 AC adaptor PQLV207Z 1 2
2 4-wire telephone line cord with
green plugs
3 2-wire telephone line cord with
transparent plugs
4 Battery HHR-P105 1 2
5 Handset cover
6 Charger PQLV30043ZB – 1
1234
56
*1 The handset cover comes attached to the handset.
*1
PQJA10088Z 1 1
PQJA10075Z 1 1
PQYNTG6700BR 1 2
Quantity
KX-TG6700 KX-TG6702
4 For assistance, please visit http://www.panasonic.com/phonehelp
TG6700.book Page 5 Tuesday, May 23, 2006 3:38 PM
Introduction
Additional/replacement accessories
Accessory item Order number
Rechargeable nickel metal
hydride (Ni-MH) battery
Headset KX-TCA60, KX-TCA86, KX-TCA88HA, KX-TCA91,
Belt clip PQKE10457Z2
Wall-mounting adaptor for
base unit
T-adaptor KX-J66
2-line splitter KX-J42
Note:
L You can expand your phone system by registering additional compatible Panasonic
units (page 5).
HHR-P105
KX-TCA92, KX-TCA93, KX-TCA94, KX-TCA95, or
KX-TCA98
PQKL10078Z2
Sales and support information
L To order additional/replacement accessories, call 1-800-332-5368.
L TTY users (hearing or speech impaired users) can call 1-866-605-1277.
Expanding your phone system
You can expand the phone system by registering the accessory handsets to a single base
unit.
Handset (optional): KX-TGA670
5.8 GHz expandable
digital cordless
handset:
Max. 8 (including
handset(s) sold with
KX-TG6700 or KXTG6702 base unit)
For assistance, please visit http://www.panasonic.com/phonehelp 5
TG6700.book Page 6 Tuesday, May 23, 2006 3:38 PM
Introduction
Important safety
instructions
When using the product, basic safety
precautions should always be followed to
reduce the risk of fire, electric shock, or
personal injury.
1. Read all instructions carefully.
2. Follow all warnings and instructions
marked on the product.
3. Unplug the product from power outlets
before cleaning. Do not use liquid or
aerosol cleaners. Use a moist cloth for
cleaning.
4. Do not use the product near water, for
example near a bathtub, wash bowl,
kitchen sink, etc.
5. Place the product securely on a stable
surface. Serious damage and/or injury
may result if the product falls.
6. Do not cover slots and openings on the
product. They are provided for
ventilation and protection against
overheating. Never place the product
near radiators, or in a place where
proper ventilation is not provided.
7. Use only the power source marked on
the product. If you are not sure of the
type of power supplied to your home,
consult your dealer or local power
company.
8. Do not place objects on the power
cord. Install the product where no one
can step or trip on the cord.
9. Do not overload power outlets and
extension cords. This can result in the
risk of fire or electric shock.
10. Never push any objects through slots
in the product. This may result in the
risk of fire or electric shock. Never spill
any liquid on the product.
11. To reduce the risk of electric shock, do
not disassemble the product. Take the
product to an authorized service center
when service is required. Opening or
removing covers may expose you to
dangerous voltages or other risks.
Incorrect reassembly can cause
electric shock when the product is
subsequently used.
12. Unplug the product from power outlets
and take to an authorized service
center when the following conditions
occur:
A. When the power cord is damaged
or frayed.
B. If liquid has been spilled into the
product.
C. If the product has been exposed to
rain or water.
D. If the product does not work
normally by following the operating
instructions. Adjust only controls
covered by the operating
instructions. Improper adjustment
may require extensive work by an
authorized service center.
E. If the product has been dropped or
physically damaged.
F. If the product exhibits a distinct
change in performance.
13. During thunderstorms, avoid using
telephones except cordless types.
There may be a remote risk of an
electric shock from lightning.
14. Do not use the product to report a gas
leak, when in the vicinity of the leak.
SAVE THESE
INSTRUCTIONS
6 For assistance, please visit http://www.panasonic.com/phonehelp
TG6700.book Page 7 Tuesday, May 23, 2006 3:38 PM
Introduction
CAUTION:
Installation
L Never install telephone wiring during a
lightning storm.
L Never install telephone jacks in wet
locations unless the jack is specifically
designed for wet locations.
L Never touch uninsulated telephone
wires or terminals unless the telephone
line has been disconnected at the
network interface.
L Use caution when installing or modifying
telephone lines.
L Do not touch the plug with wet hands.
L The AC adaptor is used as the main
disconnect device. Ensure that the AC
outlet is installed near the product and is
easily accessible.
Battery
To reduce the risk of fire or injury to
persons, read and follow these
instructions.
L Use only the battery(ies) specified.
L Do not dispose of the battery(ies) in a
fire. They may explode. Check with local
waste management codes for special
disposal instructions.
L Do not open or mutilate the battery(ies).
Released electrolyte is corrosive and
may cause burns or injury to the eyes or
skin. The electrolyte may be toxic if
swallowed.
L Exercise care when handling the
battery(ies). Do not allow conductive
materials such as rings, bracelets or
keys to touch the battery(ies), otherwise
a short circuit may cause the battery(ies)
and/or the conductive material to
overheat and cause burns.
L Charge the battery(ies) provided, or
identified for use with the product only, in
accordance with the instructions and
limitations specified in this manual.
WARNING:
L To prevent the risk of fire or electrical
shock, do not expose the product to rain
or any type of moisture.
L Unplug the product from power outlets if
it emits smoke, an abnormal smell, or
makes an unusual noise. These
conditions can cause fire or electric
shock. Confirm that smoke has stopped
emitting and contact the Panasonic Call
Center at 1-800-211-PANA (1-800-211-
7262).
Medical
L Consult the manufacturer of any
personal medical devices, such as
pacemakers or hearing aids, to
determine if they are adequately
shielded from external RF (radio
frequency) energy. (The product
operates in the frequency range of 5.76
GHz to 5.84 GHz, and the power output
is 200 mW (max.).) Do not use the
product in health care facilities if any
regulations posted in the area instruct
you not to do so. Hospitals or health care
facilities may be using equipment that
could be sensitive to external RF energy.
For assistance, please visit http://www.panasonic.com/phonehelp 7
TG6700.book Page 8 Tuesday, May 23, 2006 3:38 PM
Introduction
For best performance
Base unit location/avoiding noise
The base unit and other compatible
Panasonic units use radio waves to
communicate with each other.
For maximum distance and noise-free
operation, we recommend the following:
L Placing the product away from electrical
appliances.
L Placing the base unit in a HIGH and
CENTRAL location with no obstructions
such as walls.
L Raising the antennas vertically.
L If you use the handset near a microwave
oven which is being used, noise may be
heard. Move away from the microwave
oven and closer to the base unit.
L If you use the handset near another
cordless phone’s base unit, noise may
be heard. Move away from the other
cordless phone’s base unit and closer to
your base unit.
L The product should be kept away from
heat sources such as heaters, kitchen
stoves, etc. It should not be placed in
rooms where the temperature is less
than 5 °C (41 °F) or greater than 40 °C
(104 °F). Damp basements should also
be avoided.
L The maximum calling distance may be
shortened when the product is used in
the following places: Near obstacles
such as hills, tunnels, underground, near
metal objects such as wire fences, etc.
L Operating the product near 5.8 GHz
electrical appliances may cause
interference. Move away from the
electrical appliances.
Routine care
L Wipe the outer surface of the product
with a soft moist cloth. Do not use
benzine, thinner, or any abrasive
powder.
Environment
L Keep the product away from electrical
noise generating devices, such as
fluorescent lamps and motors.
L The product should be kept free from
excessive smoke, dust, high
temperature, and vibration.
L The product should not be exposed to
direct sunlight.
L Do not place heavy objects on top of the
product.
L When you leave the product unused for
a long period of time, unplug the product
from the power outlet.
8 For assistance, please visit http://www.panasonic.com/phonehelp
TG6700.book Page 9 Tuesday, May 23, 2006 3:38 PM
Setting up the base unit
Overview
1 Connect the AC adaptor.
2 Connect the telephone line cord.
Refer to one of the following methods depending on your situation.
L To connect to a 2-line telephone jack: page 10
L To connect to 2 single-line telephone jacks: page 10
L To connect to a single-line telephone jack: page 10
For DSL service subscribers:
L To connect to a 2-line telephone jack: page 11
L To connect to 2 single-line telephone jacks: page 11
Connecting the AC adaptor
Connect the AC adaptor, then raise the antennas.
L Use only the included Panasonic AC adaptor PQLV207.
Preparation
(120 V AC, 60 Hz)
Hook
Note:
L The AC adaptor must remain connected at all times. (It is normal for the adaptor to feel
warm during use.)
L The AC adaptor should be connected to a vertically oriented or floor-mounted AC outlet.
Do not connect the AC adaptor to a ceiling-mounted AC outlet, as the weight of the
adaptor may cause it to become disconnected.
L The unit will not work during a power failure. We recommend connecting a corded
telephone to the same telephone line or to the same telephone jack using a Panasonic
T-adaptor (page 5).
For assistance, please visit http://www.panasonic.com/phonehelp 9
TG6700.book Page 10 Tuesday, May 23, 2006 3:38 PM
Preparation
Connecting the telephone line cord
Connect the telephone line cord until it clicks into the telephone jack.
To connect to a 2-line telephone jack
4-wire telephone line cord with green plugs
To 2-line telephone jack (RJ14C)
To connect to 2 single-line telephone jacks
4-wire telephone line cord
with green plugs
To single-line telephone jacks (RJ11C)
2-wire telephone line cord
with transparent plugs
To connect to a single-line telephone jack
2-wire telephone line cord with transparent plugs
To single-line
telephone jack (RJ11C)
Note:
L Make sure you connect the telephone line cord into LINE1/2 telephone jack.
10 For assistance, please visit http://www.panasonic.com/phonehelp
Line 2
Line 1
TG6700.book Page 11 Tuesday, May 23, 2006 3:38 PM
Preparation
If you subscribe to a DSL service
Please attach a noise filter (contact your DSL provider) to the telephone line between the
base unit and the telephone line jack in the event of the following:
– Noise is heard during conversations.
– Caller ID features (page 32) do not function properly.
To connect to a 2-line telephone jack
For this connection, please purchase a Panasonic 2-line splitter (page 5).
Example: DSL line is line 2
To 2-line telephone jack (RJ14C)
LINE 2LINE 1
2-line
4-wire telephone line cord
with green plugs
splitter
2-wire telephone line cord
with transparent plugs
To connect to 2 single-line telephone jacks
Example: DSL line is line 2
4-wire telephone line cord
with green plugs
2-wire telephone line cord with transparent plugs
For assistance, please visit http://www.panasonic.com/phonehelp 11
Noise filter
To single-line telephone
jacks (RJ11C)
Line 2
Noise filter
Line 1
TG6700.book Page 12 Tuesday, May 23, 2006 3:38 PM
Preparation
Setting up the handset
Connecting the charger
(KX-TG6702 only)
L Use only the included Panasonic AC
adaptor PQLV207.
(120 V AC, 60 Hz)
Bottom of
the charger
Fasten the AC adaptor cord to prevent
it from being disconnected.
Note:
L The AC adaptor must remain connected
at all times. (It is normal for the adaptor
to feel warm during use.)
L The AC adaptor should be connected to
a vertically oriented or floor-mounted AC
outlet. Do not connect the AC adaptor to
a ceiling-mounted AC outlet, as the
weight of the adaptor may cause it to
become disconnected.
Hooks
Battery installation/replacement
1 Press the notch of the handset cover
firmly, and slide it in the direction of the
arrow.
L If necessary, remove the old battery.
2 Insert the battery (A), and press it
down until it snaps into position (B).
Then close the handset cover (C, D).
B
C
A
D
Important:
L Use only the rechargeable Panasonic
battery noted on page 5.
Attention:
A nickel metal hydride battery that is
recyclable powers the product you have
purchased.
12 For assistance, please visit http://www.panasonic.com/phonehelp
TG6700.book Page 13 Tuesday, May 23, 2006 3:38 PM
Preparation
Please call 1-800-8-BATTERY (1-800822-8837) for information on how to
recycle this battery.
Battery charge
Place the handset on the base unit or
charger for 7 hours before initial use.
While charging, the charge indicator on the
handset lights in amber. When the battery
is fully charged, “Charge completed” is
displayed.
Base unit
Charger (KX-TG6702 only)
Note:
L If you want to use the handset
immediately, charge the battery for at
least 15 minutes.
L To ensure that the battery charges
properly, clean the charge contacts of
the handset, base unit, and charger with
a soft, dry cloth once a month. Clean
more often if the unit is subject to the
exposure of grease, dust, or high
humidity.
Battery level
Battery icon Battery level
1 Fully charged
2 Medium
3 Low
Flashing: needs to be
recharged.
4 Empty
Note:
L When the battery needs to be charged,
the handset beeps intermittently during
use.
For assistance, please visit http://www.panasonic.com/phonehelp 13
TG6700.book Page 14 Tuesday, May 23, 2006 3:38 PM
Preparation
Panasonic battery performance
Operation Operating time
While in use
(talking)
While not in use
(standby)
While using the
clarity booster
feature (page 25)
Note:
L Battery operating time may be
shortened over time depending on
usage conditions and surrounding
temperature.
L Battery power is consumed whenever
the handset is off the base unit or
charger, even when the handset is not in
use. Hence the longer you leave the
handset off the base unit or charger, the
less time you may actually talk using the
handset.
L After the handset is fully charged,
displaying “Charge completed”, it
may be left on the base unit or charger
without any ill effect on the battery.
L The battery level may not be displayed
correctly after you replace the battery. In
this case, place the handset on the base
unit or charger and let charge for 7
hours.
Up to 5 hours
Up to 7 days
Up to 3 hours
Wall mounting for charger
(KX-TG6702 only)
1 Drive the screws (not included) into the
wall using the wall mount template as a
guide.
25.4 mm
(1 inch)
Screws
(120 V AC, 60 Hz)
2 Mount the charger (A), then slide it
down (B) and to the right (C) until it is
secure.
A
B
C
Wall mount template for the charger
25.4 mm
(1 inch)
14 For assistance, please visit http://www.panasonic.com/phonehelp
LINE
LINE
TG6700.book Page 15 Tuesday, May 23, 2006 3:38 PM
Controls
Base unit
Preparation
A D
LINE
1
F
LINE
2
K
JIM
HB CE G
L
P Q R S W X Y ZVUT
A {ERASE}
B {MEMO}
C Display
D {GREETING CHECK}
E {GREETING REC} (Recording)
F {LINE SELECT}
G {ANSWER ON}
H {MESSAGE}
I {LINE1}
LINE1 indicator
J {LINE2}
LINE2 indicator
K {STOP}
L IN USE indicator
M {TRANSFER} {INTERCOM}
N NO
N Antenna
O Speaker
P Charge contacts
Q {*} (TONE)
R {PAUSE} {REDIAL}
S {FLASH} {CALL WAIT}
T {MUTE}
U {SP-PHONE} (Speakerphone)
SP-PHONE indicator
V MIC (Microphone)
W Navigator key ({^} {V} {<} {>})
X {AUTO} {PROGRAM}
Y {CONF} (Conference)
Z {HOLD}
For assistance, please visit http://www.panasonic.com/phonehelp 15
TG6700.book Page 16 Tuesday, May 23, 2006 3:38 PM
Preparation
Handset
A
B
C
D
E
F
G
H
I
J
A Speaker
B Soft keys
C Headset jack
D {C} (TALK)
E Navigator key ({^} {V} {<} {>})/
SEARCH ({^} {V})
F {s} (SP-PHONE)
G {*} (TONE)
H {FLASH} {CALL WAIT}
I Microphone
J Charge contacts
K Charge indicator
Ringer indicator
Message indicator
K
L
M
N
O
P
L Receiver
M Display
N {OFF}
O {MENU}
P {HOLD} {INTERCOM}
Using the navigator key
The handset navigator key can be used to
navigate through menus and to select
items shown on the display, by pressing
{^}, {V}, {<}, or {>}.
{^}
{<}
{>}
{V}
Handset soft keys
The handset features 3 soft keys. By
pressing a soft key, you can select the
function displayed directly above it.
REDIAL
LINE2
LINE1
16 For assistance, please visit http://www.panasonic.com/phonehelp
TG6700.book Page 17 Tuesday, May 23, 2006 3:38 PM
Preparation
Displays
Base unit display items
Displayed
item
E Flashes when the date and
LINE 1
LINE 2
E Flashes when message
L1
L2
E Greeting or memo
9@ Answering system is in
Example:H1Handset number: displayed
H Paging all handsets
P Base unit is in
Meaning
time need to be set.
Indicates the selected
line(s) for the answering
system or ringer setting.
Flashing: the answering
system is answering a call
or playing a message on
the line.
memory is full.
Indicates the line 1 ringer
on the base unit is off.
Indicates the line 2 ringer
on the base unit is off.
message recording error
greeting only mode (caller
message cannot be
recorded). It is displayed
when you turn the
answering system on.
when the base unit is on
intercom call, monitoring,
or monitored by a handset.
programming mode.
Handset display items
Displayed
item
W Voice enhancer is on.
1 Battery level
k
l
SP Speaker is on.
PRIV. Call privacy mode is on.
Example:!Handset’s extension
Meaning
The line is in use.
Flashing:
– the call is put on hold on
that line.
– the answering system is
answering a call on that
line.
Flashing rapidly: a call is
being received on that line.
number.
For assistance, please visit http://www.panasonic.com/phonehelp 17
TG6700.book Page 18 Tuesday, May 23, 2006 3:38 PM
Preparation
Symbols used in these operating instructions
Symbol Meaning
{ }: button name/soft key name
Example:
Unit keys: {C}, {OFF}
Soft keys: {CID}, {C}
i Proceed to the next operation.
Example:
“Ringer tone”
Example:
The words in the brackets indicate button names/
soft key names on the handset and base unit.
The words in quotations indicate the menu on the
display.
1 {MENU} i {0}{2}
2 Select the desired setting.
3 {SAVE} i {OFF}
Handset:
{^} {V} {<} {>}
Base unit:
{^} {V} {<} {>}
1 Press {MENU}, then press {0}, {2}.
2 Press {^} or {V} to select the desired setting.
3 Press {SAVE}, then press {OFF}.
Press up, down, left, or right on the handset
navigator key.
Press up, down, left, or right on the base unit
navigator key.
18 For assistance, please visit http://www.panasonic.com/phonehelp
TG6700.book Page 19 Tuesday, May 23, 2006 3:38 PM
Preparation
Setting the unit before
use
Important:
L To program features by scrolling through
the display menus, see page 35.
Display language
The default setting is “English”.
Handset
1 {MENU} i {0}{8}
2 Select the desired setting.
3 Press the middle soft key to save. i
{OFF}
Dialing mode
If you cannot make calls, change this
setting according to your telephone line
service. The default setting is “Tone”.
“Tone”: For tone dial service.
“Pulse”: For rotary pulse dial service.
Handset
Date and time
Set the correct date and time. When you
play back a message from the answering
system (page 42), the unit announces the
day and time it was recorded.
Handset
1 {MENU} i {4}
2 Enter the current month, day, and year
by selecting 2 digits for each.
Example: August 15, 2006
{0}{8} {1}{5} {0}{6}
3 Enter the current hour and minute (12-
hour clock format) by selecting 2 digits
for each.
Example: 9:30
{0}{9} {3}{0}
4 Press {AM/PM} to select “AM” or “PM”.
i {SAVE} i {OFF}
Note:
L If you make a mistake when entering the
date and time, press {<}, {>}, {^}, or
{V} to move the cursor, then make the
correction.
1 {MENU} i {0}{5}{1}
2 Select the desired setting. i {SAVE}
i {OFF}
For assistance, please visit http://www.panasonic.com/phonehelp 19
TG6700.book Page 20 Tuesday, May 23, 2006 3:38 PM
Preparation
Line selection
The line selection mode determines which
line is selected when you press {C} on
the handset or {SP-PHONE} on the base
unit. The default setting is “Auto”.
–“Auto”: When making a call, line 1 is
selected. If that line is unavailable, line 2
is selected. When answering a call, the
ringing line is selected.
–“Line1”: Line 1 is selected.
–“Line2”: Line 2 is selected.
Handset line selection
Handset
1 {MENU} i {0}{5}{5}
2 Select the desired setting. i {SAVE}
i {OFF}
Note:
L You can select a line manually
regardless of the line selection mode by
pressing {LINE1} or {LINE2}.
Base unit line selection
Handset
1 {MENU} i {0}{*}{5}
2 Select the desired setting. i {SAVE}
i {OFF}
Note:
L You can select a line manually
regardless of the line selection mode by
pressing {LINE1} or {LINE2}.
20 For assistance, please visit http://www.panasonic.com/phonehelp
TG6700.book Page 21 Tuesday, May 23, 2006 3:38 PM
Making/Answering Calls
Making calls
While one line is in use, you can make or
answer a call using the other line.
Using the handset
1 Lift the handset and dial the phone
number.
L To correct a digit, press {CLEAR}.
2 Press {C}.
L An available line is automatically
selected and the line number is
displayed.
3 When you finish talking, press {OFF} or
place the handset on the base unit or
charger.
Note:
L The IN USE indicator on the base unit
lights while using the handset.
L You can also select a line by pressing
{LINE1} or {LINE2} in step 2.
L To change the line selection, see page
20.
Adjusting the receiver/speaker volume
Press {^} or {V} repeatedly while talking.
Making a call using the redial list
The last 5 phone numbers dialed are
stored in the redial list.
1 {REDIAL}
2 Press {^} or {V} to select the desired
number.
3 {C}
Erasing a number in the redial list
1 {REDIAL}
2 Press {^} or {V} to select the desired
number. i {ERASE}
3 {YES} i {OFF}
Using the speakerphone
1 Lift the handset, dial the phone number,
and press {s}.
L Speak alternately with the other party.
2 When you finish talking, press {OFF}.
Note:
L Use the speakerphone in a quiet
environment.
L To switch to the receiver, press {C}.
For assistance, please visit http://www.panasonic.com/phonehelp 21
TG6700.book Page 22 Tuesday, May 23, 2006 3:38 PM
Making/Answering Calls
Using the base unit
1 {SP-PHONE}
L An available line is automatically
selected and LINE1 or LINE2
indicator lights.
2 Dial the phone number.
3 When the other party answers, speak
into the MIC.
L Speak alternately with the other party.
4 When you finish talking, press {SP-
PHONE}.
Note:
L You can also select a line by pressing
{LINE1} or {LINE2} in step 1.
L Use the speakerphone in a quiet
environment.
L While on a call, you can switch from the
base unit to the handset:
– Press {LINE1} or {LINE2} on the
handset, then press {SP-PHONE} on
the base unit.
– If the handset is on the base unit,
simply lift it.
L To change the line selection, see page
20.
Understanding the indicators
The LINE1 and LINE2 indicators show the
status of each line as follows.
Status Meaning
Light off The line is free.
Light on The line is in use.
Flashing
rapidly
Flashing A call is put on hold or the
A call is being received.
answering system is
answering a call.
Adjusting the speaker volume
Press {^} or {V} repeatedly while talking.
Redialing the last number dialed
{SP-PHONE} i {REDIAL}
22 For assistance, please visit http://www.panasonic.com/phonehelp
Loading...