Page 1
Panasonic
Proprietary Telept>one
for Eiectroruc Modular Switching System
MODEL NO KX-T7130
Reference Manual
*/• ■ ^ '* .* ’
KX-T7130 •» compatitiie the Panasorsc Electronic ModUar SwAchtfig System»
end can pof^orm most furtctions withm each system
Pteese read before use
Page 2
Connection
Connect as shown.
Included accessories
Handset
.....................................
To the EMSS Control
Unit
one Card holder with memory
station card.......................... one
Overlay .....................................one
one
-1 -
Page 3
Initial setting
VOLUME
MAX
1* II
VOLUME Control:
MAX: The volume will be loud.
MIN: The volume will be soft.
CONTRAST MEMORY r
QD
«••LÜ
M«
mi] mn
W HAfCS£
T**t€AÖSfT 5£T**PfOCaAM
HANDSET
RINGER VOLUME
Qm QH)
RINGER VOLUME Selector:
HIGH: The ringing sound will be loud.
LOW: The ringing sound will be soft.
OFF: The telephone will not ring.
TO
HANDSET/HEADSET
u
HANDSET VOLUME Selector:
NORMAL: The handset volume will be soft.
HIGH: The handset volume will be loud.
TO EMSS
u
7
MEMORY Switch:
Set to “SET”.
For station programming, set to
“PROGRAM”.
HANDSET/HEADSET Selector:
Set to “HANDSET”.
CONTRAST Selector:
Set to “LOW”, “MID" or “HIGH" to choose the best
display intensity.
-2-
Page 4
Location of controls
sYsreM
—
(i>
Panaaonic
■o
3-
r^=>CE^
CT=^
H3-
V.
mm
mm
mm
mm
m c
m
m
m
J
@-
KX-T7130 IS compatible with the Panasonic Electronic Modular
Switching Systems and can perform most functions withm each
system
-3-
-®
-®
Page 5
© INTERCOM Button and
Indicator:
Used to make or receive an
intercom call.
SAVE Button:
Used to temporarily store the
number in the redial memory.
@ CONFERENCE Button and
indicator:
For talking among three
parties.
@ REDIAL Button:
For redialing the last dialed
number.
@ FLASH Button:
For sending the hooking
signal to the CO line.
(D LCD (Liquid Crystal Display)
® Programmable Feature Buttons:
For dialing or system feature
access with one touch.
@ Flexible CO Line Buttons and
Indicator: .
Used for CO line, Direct
Station Selection, or
Programmable Feature
buttons.
This function requires
upgraded versions in case of.
KX-T30810Band
KX-T61610B systems.
® Flexible Message Waiting
Button and Indicator:
Used for Message Waiting,
Direct Station Selection, or
Programmable Feature
button.
This function requires
upgraded versions in case of
KX-T30810B,
KX-T61610B and
KX-T123210DB systems.
TRANSFER Button:
Used to transfer an outside
or an intercom call to any
extension.
@ PAUSE Button:
For pausing during a dialing .
operation.
@ AUTO DIAUSTORE Button and
Indicator:
For dialing the system speed
dialing/For storing an
operating procedure into
memory.
@ AUTO ANSWER/MUTE
Button and Indicator:
For answering an intercom
call automatically/For
suspending your voice in
hands-free mode.
@ SP-PHONE Button and
Indicator:
-Used to make or receive a
phone call without using the
handset.
@ HOLD Button:
For placing a call on hold
during a conversation.
® FWD/DND Button and Indicator:
For setting or canceling the
CALL FORWARDING/DO
NOT DISTURB feature.
-4-
Page 6
Using overlay
When the System Program Switch on the EMSS Control Unit is set to the
position for programming, the function of the KX-T7130 connected to your
EMSS Control Unit will change as follows. •
...STgBS
AUTO
- SELECT
PREV
: [
-5-
Page 7
Installing the card holder
Match the marks (►) on the
card holder and on the slide
1
rails on the unit.
Push two shaded portions
siightly and insert the edges
of the holder under the slide
rails and then slide down in
direction of arrow “A”.
Removing the card holder;
Push the card holder in the
direction of arrow “B” while
keeping the tip of the holder pulled
in the direction of arrow “C”, to
take off the holder.
-6-
Page 8
Wall mounting
This unit can be mounted on the wall phone plate.
Turn around the handset
hook.
1
A Place the stand.
^ r
Rotate the stand in the
direction of the arrow.
Matsushita Electric Industrial Co., Ltd.
Central P.O.Box 288, Osaka 530-91, Japan
Printed in Japan
To temporarily place the handset
down during a conversation, hook
PQQX6404ZA F1290C2095
Loading...