Panasonic K-EF234L03E, K-EW214L03E Installation Manual

Installation Guide

Network Camera

Model No. K-EF234L03E/K-EW214L03E

K-EF234L03E

(Dome type)

z For information about how to perform the settings and how to operate the camera,

refer to the operation manual on the provided CD-ROM.

zBefore attempting to connect or operate this product, please read these instructions

carefully and save this manual for future use.

Panasonic Corporation

http://www.panasonic.com

Panasonic System Networks Co., Ltd.
Fukuoka, Japan

Authorised Representative in EU:

Panasonic Testing Centre
Panasonic Marketing Europe GmbH
Winsbergring 15, 22525 Hamburg, Germany

© Panasonic System Networks Co., Ltd. 2016

WARNING:

zTo prevent injury, this apparatus must be securely attached to the wall/ceiling in accordance

with the installation instructions.

zTo prevent fire or electric shock hazard, do not expose this apparatus to rain or moisture.

(Dome type only)
zThe apparatus should not be exposed to dripping or splashing. (Dome type only)
zAll work related to the installation of this product should be made by qualified service

personnel or system installers.
zThe installation shall be carried out in accordance with all applicable installation rules.
zThe connections should comply with local electrical code.

CAUTION:

zThe network camera is only intended for a connection to an ethernet or PoE network

without routing to the outside plant.

Disposal of Old Equipment
Only for European Union and countries with recycling systems

This symbol on the products, packaging, and/or accompanying documents means
that used electrical and electronic products must not be mixed with general
household waste.
For proper treatment, recovery and recycling of old products, please take them to
applicable collection points in accordance with your national legislation.
By disposing of them correctly, you will help to save valuable resources and prevent
any potential negative effects on human health and the environment.
For more information about collection and recycling, please contact your local
municipality.
Penalties may be applicable for incorrect disposal of this waste, in accordance with
national legislation.

K-EW214L03E

(Bullet type)

FDu0616-1066 PGQX2058YA

Printed in China

Important safety instructions

1) Read these instructions.

2) Keep these instructions.

3) Heed all warnings.

4) Follow all instructions.

5) Do not use this apparatus near water. (Dome type only)

6) Clean only with dry cloth. (Dome type only)

7) Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

8) Do not install near any heat sources such as radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce heat.

9) Only use attachments/accessories specified by the manufacturer.

10) Unplug this apparatus during lightning storms or when unused for long periods of time.

11) Refer all servicing to qualified service personnel. Servicing is required when the apparatus has
been damaged in any way, such as power-supply cord or plug is damaged, liquid has been
spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or
moisture, does not operate normally, or has been dropped.

Main functions

● 2Megapixel Full HD network camera

● H.264 and MJPEG encoding

H.264 outputs and MJPEG output can be provided.

● Wide-angle lens with day/night functionality and built-in IR-LED

Limitation of liability

THIS PUBLICATION IS PROVIDED “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER
EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY, FITNESS FOR ANY PARTICULAR PURPOSE, OR NON-INFRINGEMENT OF
THE THIRD PARTY’S RIGHT.
THIS PUBLICATION COULD INCLUDE TECHNICAL INACCURACIES OR TYPOGRAPHICAL
ERRORS. CHANGES ARE ADDED TO THE INFORMATION HEREIN, AT ANY TIME, FOR THE
IMPROVEMENTS OF THIS PUBLICATION AND/OR THE CORRESPONDING PRODUCT (S).

Disclaimer of warranty

IN NO EVENT SHALL Panasonic System Networks Co., Ltd. BE LIABLE TO ANY PARTY OR ANY
PERSON, EXCEPT FOR REPLACEMENT OR REASONABLE MAINTENANCE OF THE PRODUCT,
FOR THE CASES, INCLUDING BUT NOT LIMITED TO BELOW:
(1) ANY LOSS OR DAMAGE, INCLUDING WITHOUT LIMITATION, DIRECT OR INDIRECT, SPECIAL,

CONSEQUENTIAL OR EXEMPLARY, ARISING OUT OF OR RELATING TO THE PRODUCT;

(2) ANY INCONVENIENCE, LOSS, OR DAMAGE CAUSED BY INAPPROPRIATE USE OR

NEGLIGENT OPERATION OF THE USER;

(3) ALL MALFUNCTIONS OR TROUBLES FROM UNAUTHORIZED DISASSEMBLE, REPAIR OR

MODIFICATION OF THE PRODUCT BY THE USER, REGARDLESS OF THE CAUSE OF THE
MALFUNCTION OR TROUBLE;

(4) INCONVENIENCE OR ANY LOSS ARISING WHEN IMAGES ARE NOT DISPLAYED, DUE TO

ANY REASON OR CAUSE INCLUDING ANY FAILURE OR PROBLEM OF THE PRODUCT;

(5) ANY PROBLEM, CONSEQUENTIAL INCONVENIENCE, OR LOSS OR DAMAGE, ARISING OUT

OF THE SYSTEM COMBINED BY THE DEVICES OF THIRD PARTY;

(6) ANY CLAIM OR ACTION FOR DAMAGES, BROUGHT BY ANY PERSON OR ORGANIZATION

BEING A PHOTOGENIC SUBJECT, DUE TO VIOLATION OF PRIVACY WITH THE RESULT OF
THAT SURVEILLANCE-CAMERA’S PICTURE, INCLUDING SAVED DATA, FOR SOME REASON,
BECOMES PUBLIC OR IS USED FOR ANY PURPOSE;

(7) LOSS OF REGISTERED DATA CAUSED BY ANY FAILURE.

Open Source Software

zThis product contains open source software licensed under GPL (GNU General Public License),

LGPL (GNU Lesser General Public License), etc.

zCustomers can duplicate, distribute and modify the source code of the software under license of

GPL and/or LGPL.

zRefer to the “readme.txt” file on the provided CD-ROM for further information about open source

software licenses and the source code.

zPlease note that Panasonic shall not respond to any inquiries regarding the contents of the

source code.

Copyright

Except for open source software licensed under GPL/LGPL and so on, distributing, copying,
disassembling, reverse compiling and reverse engineering of the software provided with this
product are all expressly prohibited. In addition, exporting any software provided with this product
violating export laws is prohibited.

Network security

As you will use this unit connected to a network, your attention is called to the following security risks.

Leakage or theft of information through this unit

1

Use of this unit for illegal operations by persons with malicious intent

2

Interference with or stoppage of this unit by persons with malicious intent

3

It is your responsibility to take precautions such as those described below to protect yourself
against the above network security risks.

zUse this unit in a network secured by a firewall, etc.
zIf this unit is connected to a network that includes PCs, make sure that the system is not

infected by computer viruses or other malicious entities (using a regularly updated anti-virus
program, anti-spyware program, etc.).

zProtect your network against unauthorized access by restricting users to those who log in with

an authorized user name and password.

zApply measures such as user authentication to protect your network against leakage or theft of

information, including image data, authentication information (user names and passwords), alarm

E-mail information, FTP server information and DDNS server information.
zAfter the unit is accessed by the administrator, make sure to close the browser.
zChange the administrator password periodically.
zDo not install the camera in locations where the camera or the cables can be destroyed or

damaged by persons with malicious intent.

Precautions

WARNING

Refer installation work to the dealer.

•

Installation work requires technique and experiences. Failure to observe this may cause fire,
electric shock, injury, or damage to the product.

• Be sure to consult the dealer.

Turn the power off when do wiring of this product.

•

Failure to observe this may cause electric shock. In addition, short circuit or wrong wiring may
cause fire.

Correctly perform all wiring.

•

Short circuits in the wiring or incorrect wiring may cause fire or electrical shock.

Stop the operation immediately when something is wrong with this product.

•

When smoke goes up from the product, the smell of smoke comes from the product, or the
exterior of the product has deteriorated, continued use will cause a fire or fall of the product
resulting in injury, or damage to the product.

• In this case, turn the power off immediately and contact qualified service personnel for service.

Select an installation area that can support the total weight.

•

Selecting an inappropriate installation surface may cause this product to fall down or topple over,
resulting in injury or accidents.

• Installation work shall be started after sufficient reinforcement.

Periodic inspections shall be conducted.

•

Rust on the metal parts or screws may cause a fall of the product resulting in injury or accidents.

• Consult the dealer for the inspections.

Do not install this product in locations subject to vibration.

•

Loosening of mounting screws or bolts may cause a fall of the product resulting in injury or accidents.

Install this product in a location high enough to avoid people and objects from

•
bumping the product.

Failure to observe this may cause injury.

Do not attempt to disassemble or modify this product.

•

Failure to observe this may cause fire or electric shock. Consult the dealer for the repair or inspections.

The screws and bolts must be tightened to the specified torque.

•

Failure to observe this may cause a drop resulting in injury or accidents.

Do not insert any foreign objects.

•

Fire or electrical shock may be caused if water or any foreign objects, such as metal objects, enter
inside the unit. Turn the power off immediately and contact qualified service personnel for service.

Do not use this product in an inflammable atmosphere.

•

Failure to observe this may cause an explosion resulting in injury.

Avoid installing this product in the locations where salt damage occurs or

•
corrosive gas is produced.

Otherwise, the mounting portions will deteriorate and accidents such as a fall of the product may occur.

Do not strike or give a strong shock to this product.

•

Failure to observe this may cause fire or injury.

Do not install or clean the camera, or touch this product, the power cable or the

•
connected cables during thunder storms.

Failure to observe this may cause electric shock.

CAUTION

Turn the power off when cleaning this product.

•

Failure to observe this may cause injury.

Precautions for use

This product has no power switch.

When turning off the power, disconnect the power supply from the12 V DC power supply or the
PoE device.

To keep on using with stable performance

Do not use this camera in hot and humid conditions for a long time. Failure to observe this causes
component degradation resulting in life shortening of this product.
Do not expose this camera to direct heat sources such as a heater.

Do not touch the lens with your bare hands.

A dirty lens causes deterioration of picture quality.

Handle this camera with care.

Do not drop this camera, nor apply shock or vibration to this camera. Failure to observe this may
cause trouble. If a strong shock or vibration is applied to the enclosure, it may cause damage or
allow water to enter this product.

Product disposal/transfer

Data saved on this product or a storage device used with this product may lead to personal
information leakage. When it is necessary to dispose or give this product to someone, even when
for repair, make sure that there is no data on this product. When abandoning the memory media, it
is recommended to destroy it physically after deleting data by PC.

Cleaning this product body

Be sure to turn off the power before cleaning. Failure to observe this may cause injury. Do not use
benzine, thinner, alcohol, or any other types of solvents or detergents. Otherwise, it may cause
discoloration. When using a chemical cloth for cleaning, read the caution provided with the chemical
cloth product.

About the CMOS image sensor

zWhen continuously shooting a bright light source such as a spotlight, the color filter of the CMOS

image sensor may have deteriorated and it may cause discoloration. Even when changing the
fixed shooting direction after continuously shooting a spotlight for a certain period, the
discoloration may remain.

zWhen shooting fast-moving subjects or performing panning/tilting operations, objects crossing

the shooting area may look to be bending askew.

AVC Patent Portfolio License

THIS PRODUCT IS LICENSED UNDER THE AVC PATENT PORTFOLIO LICENSE FOR THE
PERSONAL USE OF A CONSUMER OR OTHER USES IN WHICH IT DOES NOT RECEIVE
REMUNERATION TO
(i) ENCODE VIDEO IN COMPLIANCE WITH THE AVC STANDARD (“AVC VIDEO”) AND/OR
(ii) DECODE AVC VIDEO THAT WAS ENCODED BY A CONSUMER ENGAGED IN A PERSONAL

ACTIVITY AND/OR WAS OBTAINED FROM A VIDEO PROVIDER LICENSED TO PROVIDE AVC
VIDEO. NO LICENSE IS GRANTED OR SHALL BE IMPLIED FOR ANY OTHER USE.
ADDITIONAL INFORMATION MAY BE OBTAINED FROM MPEG LA, L.L.C.
SEE HTTP://WWW.MPEGLA.COM

Equipment classification and power source indication label

Refer to the indication label on the bottom side of this unit for the equipment classification, power
source, and other information.

: Direct current symbol

Specifications

● Basic

K-EF234L03E K-EW214L03E

Power source:* 12 V DC, PoE (IEEE802.3af compliant)

Power consumption:* 12 V DC:

370 mA/Approx. 4.4 W
PoE 48 V DC:
100 mA/Approx. 4.8 W

(Class 0 device)

Operating environment
Ambient operating
temperature:
Ambient operating humidity:

Storage environment
Storage temperature:
Storage humidity:

Waterproof: Main body: IP66

Dimensions: ø108 mm × 85 mm (H)

Mass: Approx. 250 g {0.55 lbs} Approx. 380 g {0.84 lbs}

* Refer to our website (http://security.panasonic.com/support/info_d/index.html) for further

information about Power source and Power consumption.

-30 °C to +60 °C {-22 °F to 140 °F},
10 % to 90 % (no condensation)

-30 °C to +60 °C {-22 °F to 140 °F}
10 % to 95 % (no condensation)

{ø4-1/4 inches × 3-11/32 inches (H)}

12 V DC:
460 mA/Approx. 5.5 W
PoE 48 V DC:
120 mA/Approx. 5.8 W

(Class 0 device)

ø70 mm x 165 mm (D)
{ø2-3/4 inches x 6-1/2 inches (D)}

● Camera

Image sensor: Approx. 1/2.7" type CMOS image sensor

Effective pixels: Approx. 2 mega pixels

Scanning system: Progressive

Minimum illumination: 0.1 lx / F1.2 (Color)*, 0 lx / F1.2 (IR on)

* [Image Adjust] Shutter: (0-)80 ms, Gain: (0-)50”

Gain: Auto/ Manual

Back light compensation: OFF/ BLC/ HLC/ WDR

Shutter speed: Auto/ Manual, 1/3 sec~1/100000 sec

Day/Night: Auto(ICR)/ Color/ Black & White

IR LED Light: Irradiation distance: 30 m

White balance: Auto/ Sunny/ Night/ Outdoor/ Manual

Digital noise reduction: 3DNR ON/ OFF

Privacy masking: Up to 4 areas

Video Motion Detection
(VMD):

On/ Off

● Lens

Zoom ratio: 1x Optical

Focal length: 3.6 mm

Aperture: 1 : 2.1

Angular field of view: H : 90 ° V : 48 °

● Network

Network: 10BASE-T/ 100BASE-TX, RJ45 connector

Resolution: 1080P (1920x1080)/ 1.3M (1280× 960)/ 720P (1280x720)/

D1 (704x576/704x480)/ CIF (352×288/352×240)

Image compression method:

Frame Rate: 1 ~ 25/30 fps

Protocol: IPv4/ IPv6, HTTP, HTTPS, SSL, TCP/ IP, UDP, UPnP, ICMP, IGMP,

Maximum concurrent
access number:

OS Microsoft

Browser Windows

H.264/ H.264H/ H.264B/ MJPEG

RTSP, RTP, SMTP, NTP, DHCP, DNS, DDNS, FTP, QoS, Bonjour

20 users (Number of sessions that can connect to cameras at the
same time)

®

Windows® 10

®

Microsoft
Microsoft
Microsoft

Windows® 8.1

®

Windows® 8

®

Windows® 7

®

Internet Explorer® 11

Trademarks and registered trademarks

zMicrosoft, Windows, Windows Media, Internet Explorer, and ActiveX are either registered

trademarks or trademarks of Microsoft Corporation in the United States and/or other countries.
zMicrosoft product screen shot(s) reprinted with permission from Microsoft Corporation.
zAll other trademarks identified herein are the property of their respective owners.

Standard accessories

{3-11/32 inches}

Confirm the following items are included in the camera’s packaging.

Installation Guide (this document) .......... 1 pc.

RJ45 waterproof connector ................. 1 bag.

Template (Dome type only) .....................1 pc.

CD-ROM ............................................... 1 pc.

K-EF234L03E K-EW214L03E

Framework and dimension

Please refer to the following figure for dimension information.

Side view Bottom view

Framework and dimension

Please refer to the following figure for dimension information.

Side view Rear view

NOTE:

When cabling is passed through the side of the
camera, it can only pass through the slit of the
base portion of the camera, as shown to the
right.
Before opening installation holes in the ceiling or
walls, determine the direction in which you will
route cabling before installation work.

Slit of the base
portion of the camera

Connection

Device external cable

You can refer to the following figure for cable information.

1

12V DC

GND

1. LAN (Network port) ................ RJ45 waterproof jack. Connect to standard Ethernet cable.

2. 12V DC (Power input port) ..... Power port. Input 12V DC.

Assembling RJ45 waterproof connector

IMPORTANT:

zThe maximum cable length is 100 m.
zMake sure that the PoE device in use is compliant with IEEE802.3af standard.
zUse all 4 pairs (8 pins) of the Ethernet cable.
zThe external dimensions of the Ethernet cable are ø5 mm to ø6.5 mm.
zIf the procedure for the RJ45 waterproof connector (accessory) part is not correctly followed,

the waterproofing may be compromised. Do not install the camera where the RJ45
waterproof connector is exposed to constant rain or moisture.

Attach the rubber ring (accessory) to the RJ45

1

waterproof jack connected to the camera as shown.

zAttach with the flat surface of the rubber ring facing

the RJ45 waterproof jack.

First pass the Ethernet cable through the RJ45

2

waterproof connector cap (accessory), the inner rubber
(accessory) and then RJ45 waterproof connector cover
(accessory).
Next, use a specialized tool (locally procured) to crimp
the RJ45 plug (locally procured) to the end of the
Ethernet cable.

zPass the inner rubber over the cable so that the

grooved surface faces the RJ45 plug and the flat
surface faces the Ethernet cable.

Insert the inner rubber into the far end of the waterproof

3

connector cover (the direction in which multiple tabs
are open) to secure it temporarily inside the multiple
tabs.

The following steps illustrate how to attach the connector
to a camera as it is being installed.

Connect the RJ45 plug to the RJ45 waterproof jack

4

and then rotate and tighten firmly the RJ45 waterproof
connector cover.

Connect the RJ45 waterproof connector cap to the

5

RJ45 waterproof connector cover and rotate the RJ45
waterproof connector cap until there is no gap between
it and the RJ45 waterproof connector cover.

Connect 12 V DC AC adaptor to the power port (if necessary)

When the camera will run on an external power supply, use an AC adaptor that can provide a 12 V
DC 0.5 A or higher power supply.

IMPORTANT:

When cables are used outdoors, there is a chance that they may be affected by lightning.
In this case, install a lightning arrester just before where the cables connect to the camera.

CAUTION:

zA READILY ACCESSIBLE DISCONNECT DEVICE SHALL BE INCORPORATED TO THE

EQUIPMENT POWERED BY 12 V DC POWER SUPPLY.

zONLY CONNECT 12 V DC CLASS 2 POWER SUPPLY (UL1310/CSA 223) or LIMITED

POWER SOURCE (IEC/EN/UL/CSA 60950-1).

2

NOTE:

Some devices do not support PoE power supply.

When a PoE power supply is used to power the camera, the
power input port is not used. Process the jack as indicated below.
<Dome type>
Protect the jack with tape or the like to prevent dust and moisture
from collecting inside.
<Bullet type>
Appropriate waterproof treatment is performed.

Rubber ring

RJ45
waterproof jack

Flat surface

RJ45 plug
(locally
procured)

Multiple tabs

Inner rubber
(accessory)

RJ45 waterproof
jack

RJ45
waterproof
connector
cover
(accessory)

Flat surface

RJ45
waterproof
connector
cap
(accessory)

Ethernet
cable
(locally
procured)

Decorative ring

3-ø5 mm
{3/16 inches}

ø84 mm
{3-5/16 inches}

85 mm (H)

ø108 mm
{4-1/4 inches}

Pedestal

Enclosure

Camera body

17 mm

{21/32 inches}

Device Installation

Secure the camera with 3 screws (M4) (locally procured).

IMPORTANT:

zBefore starting the connection, turn off the power of the devices to be connected.
zProcure 3 screws (M4) to secure the camera to a ceiling or a wall, according to the material of

the installation area. In this case, wood screws and nails should not be used.

zRequired pull-out capacity of a single screw or anker is 196 N {20 kgf} or more.

Step 1 Remove the decorative ring and pedestal from the camera.

Turn the decorative ring counterclockwise relative to the enclosure to remove it.
Next, release the three pedestal tabs against the enclosure, and remove the pedestal as well.

NOTE:

Be careful not to drop the camera, which will no longer be supported by the pedestal once it is removed.

Step 2 Open a hole for cabling in the ceiling or wall.

Remove the template from the carton box and use it to open holes in the positions for installation
screws and the center position to pass cabling through.

NOTE:

zDetermine the screw hole diameter based on screw specifications.
zAs the cabling hole diameter, open a hole in the center of the template.

Step 3 Installing the pedestal to the ceiling or wall.

Pull the cabling through the cabling hole in the ceiling or wall, and fix the pedestal to the ceiling or
wall with 3 screws (M4).

Step 4 Connect the camera.

Connect the RJ45 waterproof connector to the camera's RJ45
waterproof jack. (Refer to steps 4 and 5 in “Assembling RJ45
waterproof connector”.)
If necessary, also connect the plug of an AC adaptor for 12 V
DC power to the power port.

Step 5 Attach the camera body and enclosure to the

pedestal.

Temporarily tilt the camera so that the camera sensor section
faces the bottom of the monitoring screen, and attach the
camera body and enclosure using the three pedestal tabs.

NOTE:

After connection, push extra cabling through the hole in the
ceiling or wall to adjust the length.

Step 6 Turn the power on and check the screen on

the computer.

Turn on power from the 12 V DC power supply or PoE device
and operate the camera. Check video from the camera on the
computer screen and refer to “Network Configuration” on the
right side of this document.

Step 7 Adjust the camera angle.

Adjust the camera angle as you check video on the computer
screen. Turn the enclosure to pan, or move the camera itself to
adjust tilt or yaw.

Step 8 Attach the decorative ring.

Finally, insert the decorative ring from the camera body side, and
turn it clockwise to secure it.

Decorative ring

NOTE:

When cabling is passed through the side of the camera, it can
only pass through the slit of the pedestal and decorative ring, as
shown to the right.
Before opening installation holes in the ceiling or walls,
determine the direction in which you will route cabling, and
arrange the template accordingly before installation work.

Sensor

PAN

YAW

Three pedestal tabs

TILT

165 mm {6-1/2 inches}

92 mm {3-5/8 inches}

3-ø4.5 mm
{3/16 inches}

ø56 mm

{2-7/32 inches}

ø70 mm

{2-3/4 inches}

Device Installation

Secure the camera with 3 screws (M4) (locally procured).

IMPORTANT:

zBefore starting the connection, turn off the power of the devices to be connected.
zProcure 3 screws (M4) to secure the camera to a ceiling or a wall, according to the material of

the installation area. In this case, wood screws and nails should not be used.

zRequired pull-out capacity of a single screw is 196 N {20 kgf} or more.

RJ45 Waterproof jack

* The figure shows the camera with

the sunshade extended.

Sunshade

Power port

Wall or Ceiling

Locking screw

Screw (M4) ×3
(locally procured)

Camera body

Step 1 Open a hole for cabling in the ceiling or wall.

Refer to the dimensional diagram of the base portion of the camera above and mark the hole
positions on the ceiling or wall, then drill holes for the installation screws and the center position to
pass cabling through.

NOTE:

zDetermine the screw hole diameter based on screw specifications.
zAs the cabling hole diameter, open a hole in the center of the base portion of the camera.

Step 2 Connect the camera.

Connect the RJ45 waterproof connector to the camera’s RJ45 waterproof jack. (Refer to steps 4
and 5 in “Assembling RJ45 waterproof connector”.)
If necessary, also connect the plug of an AC adaptor for 12 V DC power to the power port.

Step 3 Installing the camera.

Loosen the locking screw and fix the camera to
the ceiling or wall with three screws (M4) while
panning and tilting of the camera as shown to
the right.

NOTE:

After connection, push extra cabling through the
hole in the ceiling or wall to adjust the length.

Step 4 Turn the power on and check

the screen on the computer.

Turn on power from the 12 V DC power supply
or PoE device and operate the camera. Check
video from the camera on the computer screen
and refer to “Network Configuration” on the right
side of this document.

Step 5 Adjust the camera angle.

Adjust the camera angle as you check video on
the computer screen. Turn the base of the
camera to pan, or move the camera itself to
adjust tilt or yaw, as shown at upper right.
Adjust TILT or PAN angle of the camera so that
the camera sensor section faces the bottom of
the monitoring screen.
Finally, tighten the locking screw to secure the
camera’s position.
(Recommended tightening torque:

0.78 N·m {8 kgf·cm})

Sensor

TILT

PAN

YAW

Locking screw

Network Configuration

The IP address of all the cameras is the same when shipping factory (default IP192.168.0.10), in
order to make the camera get access to the network smoothly,
please plan the useable IP segment reasonably according to the actual network environment.

Modify IP Address

IP address can be acquired and modified through the “Config Tool” for the cameras which are
accessed via wired network.
In this manual, it will introduce the approach of modifying IP address via the “Config Tool”; also you
can modify the IP address in the network parameters of the web interface.

Step 1

Double click the “ConfigTool.exe” in the CD-ROM and open the “Config Tool”.

Step 2

Double click the device to be configured, the system will pop out the “Login” dialog box. Log in using
the default user name and password. Enter the new IP address, Default Gateway and Subnet Mask
into the “IP Address Modification” dialog box, then click “OK”, or enter them into the Network
Parameter tab of “Config Tool”, then click “Save”.

NOTE:

The default user name and password are “admin” and “12345”.

If the computer IP address and camera IP

Default camera IP address

or

Computer IP address

Login WEB Interface

NOTE:

Different devices may have different web interfaces, the figures below are just for
reference, please refer to the document <<WEB Operation Manual>> in the CD-ROM and the
actual interface for more details.

Step 1

Open IE and input the camera IP address in the address bar.
Alternatively, in “Config Tool”, right-click the IP address in the “Device List” and click “Open Device
Web” to open the webpage.

Step 2

The login interface is shown below, please input default user name and password (Default user
name is “admin” and password is “12345” respectively), click “login”.
When you log in for the first time, a window prompting you to update the password will pop up.
Please enter your own new password.

IMPORTANT:

zUse a combination of characters and numbers that is difficult to guess.

Avoid using a string of the same characters, such as “11111”, birth dates, or telephone

numbers.
zChange passwords periodically.
zBe sure to manage the configured user names and passwords carefully.

Step 3

Install controls according to the system prompt. The “Live” page will be displayed.

See support web page below for further details.
http://security.panasonic.com/pss/security/library/e-series.html

address are in different segments

If the computer IP address and camera IP
address are in the same segment