Panasonic HDC-SD80P, HDC-HS80P, HDC-SD80PC, HDC-HS80PC, HDC-TM80P Owner's Manual
...
For USA and Puerto Rico assistance, please call: 1-800-211-PANA(7262) or,
contact us via the web at: http://www.panasonic.com/contactinfo
For Canadian assistance, please call: 1-800-561-5505 or visit us at www.panasonic.ca
Owner’s Manual
High Definition Video Camera
Model No.HDC-SD80P/PC
HDC-TM80P/PC
HDC-HS80P/PC
Before connecting, operating or adjusting this product, please read the instructions completely.
VQT3J15
Things You Should
Date of Purchase
Know
Thank you for choosing Panasonic!
You have purchased one of the most
sophisticated and reliable products on
the market today. Used properly, we’re
sure it will bring you and your family
years of enjoyment. Please take time to
fill in the information on the right.
The serial number is on the tag located
on the underside of your camera. Be
sure to retain this manual as your
convenient camera information source.
Dealer Purchased From
Dealer Address
Dealer Phone No.
Model No.
Serial No.
Safety Precautions
WARNING:
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR PRODUCT DAMAGE,
DO NOT EXPOSE THIS APPARATUS TO RAIN, MOISTURE, DRIPPING OR
SPLASHING AND THAT NO OBJECTS FILLED WITH LIQUIDS, SUCH AS
VASES, SHALL BE PLACED ON THE APPARATUS.
USE ONLY THE RECOMMENDED ACCESSORIES.
DO NOT REMOVE THE COVER (OR BACK); THERE ARE NO USER SERVICEABLE
PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
CAUTION!
DO NOT INSTALL OR PLACE THIS UNIT IN A BOOKCASE, BUILT-IN CABINET OR IN
ANOTHER CONFINED SPACE. ENSURE THE UNIT IS WELL VENTILATED. TO
PREVENT RISK OF ELECTRIC SHOCK OR FIRE HAZARD DUE TO OVERHEATING,
ENSURE THAT CURTAINS AND ANY OTHER MATERIALS DO NOT OBSTRUCT THE
VENTILATION VENTS.
2
VQT3J15
THE FOLLOWING APPLIES ONLY IN THE U.S.A.
HDC-TM80PHDC-SD80P HDC-HS80P
FCC Note:
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: To assure continued compliance, follow the attached installation
instructions and use only shielded interface cables with ferrite
core when connecting to computer or peripheral devices.
Any changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate this equipment.
Declaration of Conformity
Trade Name: Panasonic
Model No.: HDC-SD80P/HDC-TM80P/HDC-HS80P
Responsible party: Panasonic Corporation of North America
One Panasonic Way, Secaucus, NJ 07094
Support Contact: Panasonic Consumer Electronics Company
1-800-211-PANA (7262)
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired
operation.
THE FOLLOWING APPLIES ONLY IN CANADA.
This Class B digital apparatus complies with Canadian ICES-003.
3
VQT3J15
AC adaptor
This AC adaptor operates on AC between 110 V and 240 V.
But
In the U.S.A. and Canada, the AC adaptor must be connected to a 120 V AC power
supply only.
When connecting to an AC supply outside of the U.S.A. or Canada, use a plug adaptor to
suit the AC outlet configuration.
When connecting to a supply of greater than AC 125 V, ensure the cord you use is suited
to the voltage of the AC supply and the rated current of the AC adaptor.
Contact an electrical parts distributor for assistance in selecting a suitable AC plug
adaptor or AC cord set.
The unit should be installed near an accessible AC power outlet, with the power cord
connected directly to it.
To completely disconnect power from the unit, unplug the power cord from the AC power
outlet.
Concerning the battery
Battery pack (Lithium ion battery pack)
Use the specified unit to recharge the battery pack.
Do not use the battery pack with equipment other than the specified unit.
Do not get dirt, sand, liquids, or other foreign matter on the terminals.
Do not touch the plug terminals ( and
Do not disassemble, remodel, heat or throw into fire.
If any electrolyte should come into contact with your hands or clothes, wash it off thoroughly
with water.
If any electrolyte should come into contact with your eyes, never rub the eyes. Rinse eyes
thoroughly with water, and then consult a doctor.
) with metal objects.
Warning
Risk of fire, explosion and burns. Do not disassemble, heat above 60 C (140 F) or
incinerate.
CAUTION
Danger of explosion if battery is incorrectly replaced. Replace only with the same or
equivalent type recommended by the manufacturer. Dispose of used batteries according
to the manufacturer’s instructions.
Product Identification Marking
Product Location
High Definition Video Camera Battery holder
AC adaptor Bottom
4
VQT3J15
U.S.A./CANADA CONSUMERS: ATTENTION:
A lithium ion/polymer battery that is recyclable powers the product
you have purchased. Please call 1-800-8-BATTERY for information
on how to recycle this battery.
<For USA-California only>
This product contains a CR Coin Cell Lithium Battery which contains Perchlorate Material –
special handling may apply.
See www.dtsc.ca.gov/hazardouswaste/perchlorate
.
5
VQT3J15
IMPORTANT SAFETY
INSTRUCTIONS
Read these operating instructions carefully before using the unit. Follow the safety
instructions on the unit and the applicable safety instructions listed below. Keep these
operating instructions handy for future reference.
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with dry cloth.
7) Do not block any ventilation openings.
Install in accordance with the
manufacturer’s instructions.
8) Do not install near any heat sources
such as radiators, heat registers,
stoves, or other apparatus (including
amplifiers) that produce heat.
9) Do not defeat the safety purpose of the
polarized or grounding-type plug. A
polarized plug has two blades with one
wider than the other. A grounding-type
plug has two blades and a third
grounding prong. The wide blade or the
third prong are provided for your safety.
If the provided plug does not fit into your
outlet, consult an electrician for
replacement of the obsolete outlet.
11) Only use attachments/accessories
specified by the manufacturer.
12) Use only with the
cart, stand, tripod,
bracket, or table
specified by the
manufacturer, or
sold with the
apparatus. When a
cart is used, use caution when moving
the cart/apparatus combination to avoid
injury from tip-over.
13) Unplug this apparatus during lightning
storms or when unused for long periods
of time.
14) Refer all servicing to qualified service
personnel. Servicing is required when
the apparatus has been damaged in any
way, such as power-supply cord or plug
is damaged, liquid has been spilled or
objects have fallen into the apparatus,
the apparatus has been exposed to rain
or moisture, does not operate normally,
or has been dropped.
10) Protect the power cord from being
walked on or pinched particularly at
plugs, convenience receptacles, and the
point where they exit from the
apparatus.
6
VQT3J15
Precautions
WARNING
CAUTION
USE & LOCATION
TO AVOID SHOCK HAZARD ... Your
camera and power supply should not be
exposed to rain or moisture. Do not
connect the power supply or operate your
camera if it gets wet. Your camera has
been designed for outdoor use, however it
is not designed to sustain direct exposure
to water, rain, sleet, snow, sand, dust, or a
direct splashing from a pool or even a cup
of coffee. This action could permanently
damage the internal parts of your camera.
Do not attempt to disassemble this unit.
There are no user serviceable parts
inside. Unplug your camera from the
power supply before cleaning.
AS WITH ANY SMALL OBJECT, SD
CARDS CAN BE SWALLOWED BY
YOUNG CHILDREN. DO NOT ALLOW
CHILDREN TO HANDLE THE SD CARD.
STORAGE OF YOUR CAMERA ... Store
and handle your camera in a manner that
will not subject it to unnecessary
movement (avoid shaking and striking).
Your camera contains a sensitive pick-up
device which could be damaged by
improper handling or storage.
CARE
TO CLEAN YOUR CAMERA ... Do not
use strong or abrasive detergents when
cleaning your camera body.
TO PROTECT THE LENS ... Do not touch
the surface of the lens with your hand.
Use a commercial camera lens solution
and lens paper when cleaning the lens.
Improper cleaning can scratch the lens
coating.
TO PROTECT THE FINISH OF YOUR
CAMERA ... Before handling your
camera, make sure your hands and face
are free from any chemical products, such
as suntan lotion, as it may damage the
finish.
DO NOT AIM YOUR CAMERA AT THE
SUN OR OTHER BRIGHT OBJECTS
DO NOT EXPOSE YOUR CAMERA TO
EXTENDED HIGH TEMPERATURE ...
Such as, in direct sunlight, inside a closed
car, next to a heater, etc... This action
could permanently damage the internal
parts of your camera.
AVOID SUDDEN CHANGES IN
TEMPERATURE ... If the unit is suddenly
moved from a cold place to a warm place,
moisture may form on the SD card and
inside the unit.
DO NOT LEAVE YOUR CAMERA OR
THE POWER SUPPLY TURNED ON
WHEN NOT IN USE.
-If you see this symbol-
Information on Disposal in other
Countries outside the European
Union
This symbol is only
valid in the European
Union.
If you wish to discard
this product, please
contact your local
authorities or dealer
and ask for the correct
method of disposal.
7
VQT3J15
About the recording format for
recording motion pictures
You can select from either AVCHD or iFrame
recording formats to record motion pictures
using this unit. (F 61)
AVCHD:
You can record high definition quality images
with this format. It is suitable for viewing on a
large format TV or for saving to disc.
iFrame:
This is a recording format suitable for
viewing and editing with a Mac (iMovie’11).
When using the iMovie’11, you can import
motion pictures in iFrame format quicker
than with AVCHD. You can also make the
file size of the imported motion picture
smaller than when importing AVCHD.
It is not compatible with motion picture
recorded in AVCHD format.
Indemnity about recorded
content
Panasonic does not accept any
responsibility for damages directly or
indirectly due to any type of problems that
result in loss of recording or edited content,
and does not guarantee any content if
recording or editing does not work properly.
Likewise, the above also applies in a case
where any type of repair is made to the unit
(including any other non-built-in memory/
HDD related component).
Handling of built-in memory
[HDC-TM80]
This unit is equipped with the built-in
memory. When using this component, pay
attention to the following points.
Back up data periodically.
The built-in memory is temporary storage. In
order to avoid erasing data due to static
electricity, electromagnetic waves,
breakage, and failures, back up the data to a
PC or DVD disc. (F 100, 110)
Access lamp [ACCESS] (F 18)
illuminates while the SD card or built-in
memory is being accessed (initialization,
recording, playback, deleting etc.). Do not
perform the following operations when the
lamp illuminates. It may damage the builtin memory or cause a malfunction in the
unit.
Turn the unit off (remove the battery)
Insert and remove the USB cable
Expose the unit to vibrations or shock
About disposing of or giving away this unit.
(F 135)
Handling of HDD [HDC-HS80]
This unit is equipped with the built-in HDD.
While the HDD is capable of storing a large
amount of data, there are a few things to
look out for. When using this component,
pay attention to the following points.
Do not expose the HDD to vibrations and
shocks.
Due to the environment and handling
conditions, the HDD may be subject to
partial damages or may not be able to read,
record, and play back data. Do not expose
the unit to vibrations or shock, and do not
turn off the unit during recording or playback.
If the unit is used in a place with loud
sounds, such as a club or similar venue,
the recording may stop due to sound
vibrations. Recording data on an SD card
is recommended in these places.
Back up data periodically.
The HDD is temporary storage. In order to
avoid erasing data due to static electricity,
electromagnetic waves, breakage, and
failures, back up the data to a PC or DVD
disc. (F 100, 110)
If the HDD experiences any abnormality,
back up data immediately.
Failure in the HDD may produce continuous
noise or choppy sound during recording or
playing back. Continuous use will cause
further deterioration, and may eventually
disable the HDD. If these phenomena are
observed, copy the data on the HDD to a PC,
a DVD disc etc. immediately and contact
consumer support. (
Once the HDD is out of order, data cannot
be restored.
F
152, 153)
8
VQT3J15
Operation may stop in hot or cold
environments.
The unit is disabled in order to protect the
HDD.
Do not use the unit in low atmospheric
pressures.
The HDD may fail if it is used at altitudes of
3000 m (9800 feet) or higher above sea
level.
Transportation
When the unit is transported, turn off the unit
and be careful not to shake, drop, or cause
impact to the unit.
Falling detection
[ ] is indicated on the screen when it
detects a falling state (a weightless state). If
the falling state is detected repeatedly, the
unit may stop the recording or playback
operation in order to protect the HDD.
HDD access lamp [ACCESS HDD] (F 19)
illuminates while the HDD is being
accessed (initialization, recording,
playback, deleting etc.). Do not perform
the following operations when the lamp
illuminates. It may damage the HDD or
cause a malfunction in the unit.
Turn the unit off (remove the battery)
Insert and remove the USB cable
Expose the unit to vibrations or shock
About disposing of or giving away this unit.
(F 135)
For the purposes of this
owner’s manual
SD Memory Card, SDHC Memory Card
and SDXC Memory Card are referred to
as the “SD card”.
Functions that can be used for Motion
Picture Recording Mode:
Functions that can be used for Still Picture
Recording Mode:
Functions that can be used for Motion
Picture Playback Mode:
Functions that can be used for Still Picture
Playback Mode:
Pages for reference are indicated by an
arrow, for example: F 00
This owner’s manual is designed for use
with models ,
and . Pictures may be
slightly different from the original.
The illustrations used in this owner’s
manual show model ,
however, parts of the explanation refer
to different models.
Depending on the model, some
functions are not available.
Features may vary, so please read
carefully.
Not all models may be available
depending on the region of purchase.
Cards that you can use with
this unit
SD Memory Card, SDHC Memory Card
and SDXC Memory Card
4 GB or more Memory Cards that do not
have the SDHC logo or 48 GB or more
Memory Cards that do not have the SDXC
logo are not based on SD Memory Card
Specifications.
Refer to page 24 for more details on SD
cards.
9
VQT3J15
Contents
Accessories............................................. 12
Quick Guide.............................................13
Advanced (Recording)
Preparation
Parts identification and handling ..........17
Power supply........................................... 20
Inserting/removing the battery........... 20
Charging the battery ......................... 21
Charging and recording time............. 22
Recording to a card ................................ 24
Cards that you can use with
this unit.............................................. 24
Inserting/removing an SD card.......... 25
Turning the unit on/off............................26
Turning the unit on and off with the
power button ..................................... 26
Turning the unit on and off with the
LCD monitor...................................... 26
Selecting a mode .................................... 27
How to use the touch screen ................. 27
About the Touch Menu ...................... 28
Setting date and time.............................. 29
Basic
Before recording ..................................... 30
Selecting a media to record
[HDC-TM80/HDC-HS80] ..........................31
Recording motion pictures .................... 32
Recording still pictures .......................... 34
Recording still pictures in
Motion Picture Recording Mode........ 35
Intelligent Auto Mode ............................. 36
Motion picture/Still picture playback .... 38
Using the menu screen .......................... 41
Using the Setup Menu ............................ 42
Zoom in/out function .............................. 49
Extra Optical Zoom ........................... 49
Image Stabilizer Function ...................... 50
Recording with the Touch function....... 51
Touch function icons ......................... 51
Recording functions of
operation icons ....................................... 54
Operation icons................................. 54
Recording functions of menus .............. 60
Manual recording.................................... 72
White balance ................................... 73
Manual shutter speed/
iris adjustment................................... 74
Manual focus adjustment .................. 75
Advanced (Playback)
Playback Operations .............................. 76
Motion picture playback using
operation icon ................................... 76
Creating still picture from
motion picture ................................... 77
Highlight & Time frame index............ 78
Repeat playback ............................... 78
Resuming the previous playback...... 79
Zooming in on a still picture during
playback (Playback zoom) ................ 79
Various playback functions ................... 80
Playing back motion pictures/
still pictures by date .......................... 80
Highlight Playback ............................ 81
Changing the playback settings and
playing back the slide show .............. 83
Deleting scenes/still pictures ................ 85
Dividing a scene (AVCHD)................ 86
Dividing a scene to partially delete
(iFrame) ............................................ 87
Deleting personal information ........... 88
Protecting scenes/still pictures ......... 88
DPOF setting ........................................... 89
Relay scene combining
[HDC-TM80] ............................................. 90
10
VQT3J15
Watching Video/Pictures on your TV .... 92
Connecting with a HDMI mini
cable ................................................. 95
Connecting with the AV multi
cable ................................................. 95
Playback using VIERA Link
™
................96
Copy/Dubbing
Copying between SD card and Built-in
Memory/HDD
[HDC-TM80/HDC-HS80] ..........................98
Connecting a DVD burner to copy to/
play back a disc ....................................100
Preparing for copying/
playing back .................................... 100
Copying to discs.............................. 102
Playing back the copied disc........... 104
Managing the copied disc ............... 105
Dubbing with a Blu-ray disc recorder,
video, etc. .............................................. 106
With a PC
What you can do with a PC .................. 110
End User License Agreement ......... 112
Operating environment ........................ 113
Installation ............................................. 116
Connecting to a PC ............................... 118
About the PC display ...................... 120
Starting HD Writer AE 3.0 ..................... 121
Reading the operating instructions
of the software applications............. 121
If using Mac ........................................... 122
Others
Indications............................................. 123
Messages .............................................. 126
About recovery................................ 127
Troubleshooting ................................... 128
Cautions for use ................................... 134
About copyright .................................... 140
Recording modes/approximate
recordable time ..................................... 141
Approximate number of recordable
pictures.................................................. 142
Specifications ....................................... 143
Optional accessories ........................... 148
Accessory Order Form
(For USA and Puerto Rico
Customers) ..................................... 150
Limited Warranty (ONLY FOR U.S.A.
AND PUERTO RICO)............................. 151
Warranty
(For Canadian Customers)................... 153
Index ...................................................... 154
Spanish Quick Use Guide/
Guía española para el uso rápido ....... 156
PreparationBasicAdvanced
(Recording)
(Playback)
Copy/DubbingWith a PCOthers Advanced
11
VQT3J15
Accessories
Check the accessories before using this unit.
Keep the accessories out of reach of children to prevent swallowing.
Product numbers correct as of Dec. 2010. These may be subject to change.
Battery pack
VW-VBK180
AC adaptor
VSK0711
AC cable
K2CA2CA00025
AV multi cable
K1HY12YY0008
USB cable
K1HA05AD0007
Stylus pen
VGQ0C14
This is used for operations that are hard to
operate with your fingers or performing
detailed operations with the touch screen
operation. (F 27, 48)
CD-ROM
Software
12
VQT3J15
Quick Guide
Inserting the battery
Install the battery by inserting it in the
direction shown in the figure.
Insert the battery until it clicks and locks.
Charging the battery
Inserting/removing an SD card
Access lamp [ACCESS]
When this unit is accessing the SD
card or built-in memory, the access
lamp lights up.
DC input terminal
Connect the AC adaptor to the DC input
terminal.
Connect the AC cable to the AC
adaptor, then the AC outlet.
The status indicator will flash red at an
interval of 2 seconds, indicating that
charging has begun.
It will turn off when the charging is
completed.
Check that the access lamp has gone off.
1) Open the SD card cover and insert
(remove) the SD card into (from) the
card slot .
Face the label side in the direction
shown in the illustration and press it
straight in as far as it will go.
Press the center of the SD card and then
pull it straight out.
2) Securely close the SD card cover.
Securely close it until it clicks.
13
VQT3J15
Turning the unit on/off
Turning the unit on and off with the
power button
Open the LCD monitor and press the power
button to turn on the unit.
The status indicator lights on.
To turn off the unit, hold down the power
button until the status indicator goes off.
Selecting a mode
Operate the mode switch to change the
mode to , or .
Motion Picture Recording
Mode (F 32)
Still Picture Recording Mode
(F 34)
Playback Mode (F 38, 76)
Turning the unit on and off with the LCD
monitor
Opening the LCD monitor turns on the unit.
Closing the LCD monitor turns off the unit.
To turn on the unit
The status indicator lights on.
To turn off the unit
How to use the touch screen
You can operate by directly touching the
LCD monitor (touch screen) with your finger.
It is easier to use the stylus pen (supplied)
for detailed operation or if it is hard to
operate with your fingers.
Touch
Touch and release the touch screen to select
icon or picture.
Slide while touching
Move your finger while pressing on the touch
screen.
The status indicator goes off.
14
VQT3J15
Touch Menu
MENU
T
W
Touch to display the Touch Menu.
Touch (left side)/ (right side) of on
the Touch Menu to switch the operation
icons.
T
W
Touch Menu
Recording motion pictures
1) Change the mode to .
2) Open the LCD monitor.
3) Press the recording start/stop button to
start recording.
Language selection
1) Touch [MENU], then touch [SETUP]
[LANGUAGE].
2) Touch desired language.
Selecting a media to record
[HDC-TM80/HDC-HS80]
1) Change the mode to or .
2) Select the menu.
: [MEDIA SELECT]
3) Touch the media to record motion
pictures or still pictures.
Touch [VIDEO/SD CARD] or [PICTURE/
SD CARD] to record to the SD card.
Touch [VIDEO/Built-inMemory] or
[PICTURE/Built-inMemory] to record to
the built-in memory.
When you begin recording, changes
to .
Recording still pictures
1) Change the mode to .
2) Open the LCD monitor.
3) Press the button fully to take the
picture.
Touch [VIDEO/HDD] or [PICTURE/HDD]
to record to the HDD.
The media is selected separately to
motion pictures or still pictures is
highlighted in yellow.
4) Touch [ENTER].
15
VQT3J15
Motion picture/Still picture
0h01m30s
playback
1) Change the mode to .
2) Touch the play mode select icon .
ALL
3)
Select the [VIDEO/PICTURE] you wish
to play back.
/
Select the [MEDIA] and [VIDEO/
PICTURE] you wish to play back.
Touch [ENTER].
4) Touch the scene or the still picture to be
played back.
Operation icons and screen display will
disappear when no function is performed
for a specific period of time. To display
them again, touch the screen.
(Motion picture playback)
/: Playback/Pause
: Rewind playback
: Fast forward playback
: Stops the playback and shows
the thumbnails.
(Still picture playback)
/: Slide show (playback of the still
pictures in numerical order) start/
pause.
: Plays back the previous picture.
: Plays back the next picture.
: Stops the playback and shows
the thumbnails.
ALL
is displayed when [AVCHD] is
touched or is displayed when
[iFrame] is touched in step 3.
To display the next (previous) page:
Slide the thumbnail display upward
(downward) while touching it.
Switch the Touch Menu, and then
touch (up) / (down) on the
thumbnail scroll lever.
5) Select the playback operation by
touching the operation icon.
0h01m30s
0h01m30s
Operation icon
16
VQT3J15
Preparation
10
Parts identification and handling
1 Speaker
2 USB terminal [ ] (F 101, 106, 118)
1
2
3
4
5
AV MULTI
867
3 Intelligent auto/Manual button
[iA/MANUAL] (F 36, 72)
4 Optical image stabilizer button
[ O.I.S.] (F 50)
5 Power button [ ] (F 26)
6 HDMI mini connector [HDMI]
(F 92, 96)
7 AV multi connector (F 92, 109)
Use the AV multi cable (only the supplied
cable).
8 Battery release lever [BATT] (F 20)
9
9 Lens cover closing switch
The lens cover will open automatically when
set to Motion Picture Recording Mode
or Still Picture Recording Mode. (F 27)
When not using the unit, close the lens
cover to protect the lens.
Lens cover does not close automatically.
Slide the Lens cover closing switch to
close the cover.
11
12
13
10 Lens cover
11 LED light
It can be used as a Video light or Photo
light. (F 57, 71)
12 Lens
13 Internal stereo microphones
17
VQT3J15
14 Mode switch (F 27)
14
15 16
1817
19
21
22
20
15 Status indicator (F 26)
16 Recording start/stop button (F 32)
17 LCD monitor (Touch screen) (F 27)
It can open up to 90.
It can rotate up to 180 towards the lens
or 90towards the opposite direction.
Due to limitations in LCD production
technology, there may be some tiny bright
or dark spots on the LCD monitor screen.
However, this is not a malfunction and
does not affect the recorded picture.
18 Battery holder (F 20)
19 Tripod receptacle
If you attach a tripod which has 5.5 mm
(0.22 ) screw or larger, it may damage
this unit.
20 SD card cover (F 25)
21 Access lamp [ACCESS] (F 25)
22 Card slot (F 25)
18
VQT3J15
/
27
28
2423
23 Photoshot button [ ] (F 34)
24 Zoom lever [W/T] (In Motion Picture
Recording Mode or Still Picture
Recording Mode) (F 49)
Thumbnail display switch [ / ]/
Volume lever [VOL] (In Playback
Mode) (F 39)
25 Grip belt
Adjust the length of the grip belt so that it fits
your hand.
25
Flip the belt.
Adjust the length.
26
Replace the belt.
26 DC input terminal [DC IN] (F 21)
Do not use any other AC adaptors except
the supplied one.
27 HDD access lamp [ACCESS HDD]
28 DC input terminal [DC IN] (F 21)
Do not use any other AC adaptors except
the supplied one.
19
VQT3J15
Preparation
Removing the battery
Be sure to hold down the power button until the status
indicator goes off. Then remove the battery while
supporting the unit to prevent it from dropping.
Move the battery release lever in the direction
indicated by the arrow and remove the battery
when unlocked.
ャモヵヵ
Power supply
About batteries that you can use with this unit
The battery that can be used with this unit is VW-VBK180/VW-VBK360.
The unit has a function for distinguishing batteries which can be used safely. The
dedicated battery (VW-VBK180/VW-VBK360) supports this function. The only
batteries suitable for use with this unit are genuine Panasonic products and
batteries manufactured by other companies and certified by Panasonic. (Batteries
which do not support this function cannot be used). Panasonic cannot in any way
guarantee the quality, performance or safety of batteries which have been
manufactured by other companies and are not genuine Panasonic products.
It has been found that counterfeit battery packs which look very similar to the genuine
product are made available to purchase in some markets. Some of these battery packs
are not adequately protected with internal protection to meet the requirements of
appropriate safety standards. There is a possibility that these battery packs may lead
to fire or explosion. Please be advised that we are not liable for any accident or failure
occurring as a result of use of a counterfeit battery pack. To ensure that safe products
are used we would recommend that a genuine Panasonic battery pack is used.
Inserting/removing the battery
Press the power button to turn off the unit. (F 26)
Install the battery by inserting it in the direction shown in the figure.
Insert the battery until it
clicks and locks.
20
VQT3J15
Charging the battery
When this unit is purchased, the battery is not charged. Charge the battery fully
before using this unit for the first time.
Important:
Use the supplied AC adaptor. Do not use the AC adaptor of another device.
Do not use the AC cable with any other equipment as it is designed only for this unit.
Also, do not use the AC cable from other equipment with this unit.
The battery can also be charged using a battery charger (VW-BC10PP; optional).
The battery will not be charged if the unit is turned on.
It is recommended to charge the battery in a temperature between 10 C to 30 C
(50 °F to 86 °F). (The battery temperature should also be the same.)
DC input terminal
Insert the plugs as far as they will go.
1 Connect the AC adaptor to the DC input terminal.
2 Connect the AC cable to the AC adaptor, then the AC outlet.
The status indicator will flash red at an interval of 2 seconds, indicating that charging has begun.
It will turn off when the charging is completed.
Connecting to the AC outlet
If you turn on the unit while connecting the AC adaptor, you can use the unit with power
supplied from the outlet.
If the status indicator flashes at a particularly fast or slow rate, refer to page 137.
We recommend using Panasonic batteries (F 12, 22, 23, 148).
If you use other batteries, we cannot guarantee the quality of this product.
Do not heat or expose to flame.
Do not leave the battery(ies) in an automobile exposed to direct sunlight for a long period
of time with doors and windows closed.
21
VQT3J15
Charging and recording time
Charging/Recording time
Temperature: 25 C (77 F)/humidity: 60%RH (When using AC adaptor)
HDC-SD80
Battery model number
[Voltage/Capacity
(minimum)]
Supplied battery/
VW-VBK180 (optional)
[3.6 V/1790 mAh]
VW-VBK360 (optional)
[3.6 V/3580 mAh]
Battery model number
[Voltage/Capacity
(minimum)]
Supplied battery/
VW-VBK180 (optional)
[3.6 V/1790 mAh]
Charging
time
2h25min
4h20min
Charging
time
2h25min
Recording
mode
[HA], [HG] 1 h 50 min
[HX], [HE] 1 h 55 min
[iFrame] 2h 1h
[HA], [HG],
[HX], [HE]
[iFrame] 3 h 55 min 2 h
HDC-TM80
Recording
mode
[HA], [HG] 1 h 50 min
[HX], [HE] 1 h 55 min
[iFrame] 2h 1h
Maximum
continuous
recordable time
3h45min 1h55min
Maximum
continuous
recordable time
Actual
recordable
time
55 min
Actual
recordable
time
55 min
VW-VBK360 (optional)
[3.6 V/3580 mAh]
22
VQT3J15
4h20min
[HA], [HG],
[HX], [HE]
[iFrame] 3 h 55 min 2 h
3h45min 1h55min
HDC-HS80
Battery model
number
[Voltage/Capacity
(minimum)]
Supplied battery/
VW-VBK180
(optional)
[3.6 V/1790 mAh]
VW-VBK360
(optional)
[3.6 V/3580 mAh]
Charging
time
2h25min
4h20min
Recording
destination
HDD
SD
HDD
SD
Recording
mode
[HA], [HG],
[HX], [HE]
Maximum
continuous
recordable
time
1h35min
Actual
recordable
time
50 min
[iFrame] 1 h 45 min
[HA], [HG],
[HX], [HE]
1h40min 50min
[iFrame] 1h45min 55min
[HA], [HG],
[HX], [HE]
[iFrame] 3 h 25 min
[HA], [HG],
[HX], [HE]
[iFrame] 3 h 35 min
3h15min
3h25min
1h40min
1h45min
1h45min
1h50min
These times are approximations.
The indicated charging time is for when the battery has been discharged completely.
Charging time and recordable time vary depending on the usage conditions such as
high/low temperature.
The actual recordable time refers to the recordable time when repeatedly starting/stopping
recording, turning the unit on/off, moving the zoom lever etc.
The batteries heat up after use or charging. This is not a malfunction.
Battery capacity indication
The display changes as the battery capacity reduces.
If there is less than 3 minutes remaining, then will become red. If the battery
discharges, then will flash.
The remaining battery capacity is displayed when using the Panasonic battery that you
can use for this unit. The actual time can vary depending on your actual use.
When using the AC adaptor or batteries made by other companies, the remaining
battery capacity will not be shown.
23
VQT3J15
Preparation
32
Recording to a card
The unit can record still pictures or motion pictures to an SD card, built-in memory or HDD.
To record to an SD card, read the following.
This unit (an SDXC compatible device) is compatible with SD Memory Cards, SDHC
Memory Cards and SDXC Memory Cards. When using an SDHC memory card/SDXC
memory card with other equipment, check the equipment is compatible with these
memory cards.
Cards that you can use with this unit
Use SD cards conforming to Class 4 or higher of the SD Speed Class Rating* for
motion picture recording.
Card type Capacity Motion picture recording
8MB/16MB/
32 MB
SD
Memory
Card
SDHC
Memory
Card
SDXC
Memory
Card
* SD Speed Class Rating is the speed
standard regarding continuous writing.
Check via the label on the card, etc.
Please confirm the latest information about SD Memory Cards/SDHC Memory Cards/SDXC
Memory Cards that can be used for motion picture recording on the following website.
http://panasonic.jp/support/global/cs/e_cam
(This website is in English only.)
4 GB or more Memory Cards that do not have the SDHC logo or 48 GB
or more Memory Cards that do not have the SDXC logo are not based
on SD Memory Card Specifications.
When the write-protect switch on SD card is locked, no recording,
deletion or editing will be possible on the card.
Keep the Memory Card out of reach of children to prevent swallowing.
64 MB/128 MB/
256 MB
512MB/1GB/
2GB
4GB/6GB/8GB/
12 GB/16 GB/
24 GB/32 GB
48 GB/64 GB
Cannot be used.
Cannot be guaranteed in operation.
Can be used. Can be used.
e.g.:
Still picture
recording
Cannot be
guaranteed in
operation.
24
VQT3J15
Inserting/removing an SD card
When using an SD card not from Panasonic, or one previously used on other equipment, for
the first time on this unit, format the SD card. (
of the recorded data is deleted. Once the data is deleted, it cannot be restored.
Caution:
Check that the access lamp has gone off.
F
46, 47) When the SD card is formatted, all
Access lamp [ACCESS]
When this unit is accessing the SD
card or built-in memory, the access
lamp lights up.
1 Open the SD card cover and
insert (remove) the SD card
into (from) the card slot .
Face the label side in the direction
shown in the illustration and press it
straight in as far as it will go.
Press the center of the SD card and then
pull it straight out.
Do not touch the terminals on the back of
the SD card.
Do not apply strong shocks, bend, or drop
the SD card.
Electrical noise, static electricity or the
failure of this unit or the SD card may
damage or erase the data stored on the
SD card.
When the card access lamp is lit, do not:
Remove the SD card
Turn the unit off
Insert and remove the USB cable
Expose the unit to vibrations or shock
Performing the above while the lamp is on
may result in damage to data/SD card or
this unit.
Do not expose the terminals of the SD
card to water, dirt or dust.
2 Securely close the SD card
cover.
Securely close it until it clicks.
Do not place SD cards in the following
areas:
In direct sunlight
In very dusty or humid areas
Near a heater
Locations susceptible to significant
difference in temperature (condensation
can occur.)
Where static electricity or
electromagnetic waves occur
To protect SD cards, return them to their
cases when you are not using them.
About disposing of or giving away the SD
card. (F 138)
25
VQT3J15
Preparation
Turning the unit on/off
You can turn the unit on and off using the power button or by opening and closing the LCD
monitor.
A clicking sound is heard when the unit is shaken.
This is the sound of the lens moving and is not a defect.
This sound will no longer be heard when the unit is turned on and change the mode to
or .
Turning the unit on and off with the power button
Open the LCD monitor and press the power button to turn on the unit.
To turn off the unit
Hold down the power button until the
status indicator goes off.
The status indicator lights on.
Turning the unit on and off with the LCD monitor
Unit is turned on when the LCD monitor is opened, and unit is turned off when it is closed.
During normal use, opening and closing of the LCD monitor can be conveniently used
to turn the unit on/off.
To turn on the unit
The status indicator lights on.
The unit will not turn off while recording motion pictures even if the LCD monitor is closed.
In the following cases, opening the LCD monitor does not turn on the unit. Press the power
button to turn on the unit.
When the unit is originally purchased
When you have turned off the unit using the power button
To turn off the unit
The status indicator goes off.
26
VQT3J15
Preparation
Selecting a mode
Change the mode to recording or playback.
Operate the mode switch to change the mode to , or .
Motion Picture Recording Mode (F 32)
Still Picture Recording Mode (F 34)
Playback Mode (F 38, 76)
Preparation
How to use the touch screen
You can operate by directly touching the LCD monitor (touch screen) with your finger.
It is easier to use the stylus pen (supplied) for detailed operation or if it is hard to operate with
your fingers.
Touch
Touch and release the touch screen to select icon or
picture.
Touch the center of the icon.
Touching the touch screen will not operate while you
are touching another part of the touch screen.
Slide while touching
Move your finger while pressing on the touch screen.
27
VQT3J15
About the operation icons
///:
These icons are used to switch the menu and thumbnail
display page, for item selection and setting etc.
:
Touch to return to the previous screen such as when
setting menus.
About the Touch Menu
Touch (left side)/ (right side) of on the Touch Menu to switch the operation icons.
Touch (left side)/ (right side) of on the Touch Menu.
It is also possible to switch the operation icons by sliding the Touch Menu right or left while
touching it.
Touch Menu
T
W
Recording Mode Playback Mode
T
W
FOCUS
WB
SHTR
IRIS
MENU
Touch these icons to switch pages upward or downward.
Displayed only during the Manual Mode.
To display the Touch Menu
The Touch Menu will disappear when no function is
performed for a specific period of time during
Recording mode. To display it again, touch .
ALL
MENU
28
VQT3J15
Do not touch on the LCD monitor with hard pointed tips, such as ball point pens.
MENU
Perform the touch screen calibration when the touch is not recognized or wrong location is
recognized. (F 48)
Preparation
Setting date and time
When the unit is turned on for the first time, a message asking you to set the date and time
will appear.
Select [YES] and perform steps 2 to 3 below to set the date and time.
1 Select the menu. (F 41)
: [SETUP] [CLOCK SET]
2
Touch the date or time to be set, then set the desired value using / .
Displaying the World time setting (F 42):
[HOME]/ [DESTINATION]
The year can be set between 2000 and 2039.
The 12-hour system is used to display the time.
3 Touch [ENTER].
A message prompting for World time setting may be
displayed. Perform the World time setting by touching the screen. (F 42)
Touch [EXIT] to complete the setting.
The date and time function is driven by a built-in lithium battery.
When this unit is purchased, the clock is set. If the time display becomes [- -], the built-in
lithium battery needs to be charged. To recharge the built-in lithium battery, connect the AC
adaptor or attach the battery to this unit. Leave the unit as it is for approx. 24 hours and the
battery will maintain the date and time for approx. 4 months. (The battery is still being
recharged even if the unit is off.)
29
VQT3J15
Basic
Before recording
Basic camera positioning
Hold the unit with both hands.
Put your hand through the grip belt.
It is convenient to use the Recording button icon when holding the unit at waist level.
When recording, make sure your footing is stable and there is no danger of colliding with
another person or object.
When you are outdoors, record pictures with the sunlight behind you. If the subject is
backlit, it will become dark in the recording.
Keep your arms near your body and separate your legs for better balance.
Do not cover the microphones with your hand etc.
Basic motion picture recording
The unit should normally be held steady when recording.
If you move the unit when recording, do so slowly, maintaining a constant speed.
The zoom operation is useful for recording subjects you cannot get close to, but overuse of
zoom in and zoom out can make the resulting motion picture less enjoyable to watch.
Recording Yourself
Rotate the LCD monitor towards the lens side.
The image is horizontally flipped as if you see a mirror
image. (However the image recorded is the same as a
normal recording.)
Only some indications will appear on the screen. When
appears, return the direction of the LCD monitor to
normal position and check the warning/alarm indication.
(F 126)
30
VQT3J15
Loading...