Panasonic HC-V10EB, HC-V10EC, HC-V10P, HC-V10EF, HC-V10EG Service Manual
...
© Panasonic Corporation 2012 Unauthorized copying and distribution is a violation of law.
ORDER NO. VM1202004CE
B27
Digital Video Camera
Model No. HC-V10P
HC-V10PC
HC-V10PU
HC-V10EB
HC-V10EC
HC-V10EE
HC-V10EF
HC-V10EG
HC-V10EP
HC-V10GA
HC-V10GC
HC-V10GK
HC-V10GN
HC-V10GT
HC-V10GW
HC-V10MPU
HC-V11MPU
Colour
[ HC-V10 ]
(K)...........Black Type
(R)...........Red Type (except PC/EF/GK/GN/GT/GW)
(S)...........Silver Type (only P/GA/GC/GK/GN)
[ HC-V10M / HC-V11M ]
(K)...........Black Type
2
TABLE OF CONTENTS
PAG E PAG E
1 Safety Precautions -----------------------------------------------3
1.1. General Guidelines ----------------------------------------3
1.2. Leakage Current Cold Check ---------------------------3
1.3. Leakage Current Hot Check (See Figure 1.) --------3
2Warning--------------------------------------------------------------4
2.1. Prevention of Electrostatic Discharge (ESD)
to Electrostatically Sensitive (ES) Devices ----------4
2.2. How to Recycle the Lithium Ion Battery (U.S.
Only)-----------------------------------------------------------4
2.3. How to Replace the Lithium Battery -------------------5
3 Service Navigation------------------------------------------------6
3.1. Introduction --------------------------------------------------6
3.2. General Description About Lead Free Solder
(PbF) ----------------------------------------------------------6
3.3. Important Notice 1:(Other than U.S.A. and
Canadian Market) ------------------------------------------6
3.4. How to Define the Model Suffix (NTSC or PAL
model)---------------------------------------------------------7
3.5. Formatting----------------------------------------------------8
4 Specifications ------------------------------------------------------9
5 Location of Controls and Components ------------------ 11
6 Service Mode ----------------------------------------------------- 13
6.1. History Display -------------------------------------------- 14
7 Service Fixture & Tools --------------------------------------- 15
7.1. When Replacing the Main P.C.B. -------------------- 15
7.2. Service Position ------------------------------------------ 15
8 Disassembly and Assembly Instructions --------------- 16
8.1. Disassembly Flow Chart for the Unit ---------------- 16
8.2. PCB Location---------------------------------------------- 16
8.3. Disassembly Procedure for the Unit ---------------- 17
9 Measurements and Adjustments -------------------------- 24
9.1. Electric Adjustment --------------------------------------24
10 Factory Setting--------------------------------------------------- 26
10.1. How To Turn On The Factory Settings? ------------ 26
10.2. What Is The Factory Settings? ----------------------- 26
11 Blo ck D iagram --------------------------------------------------- 27
11.1. Overall Block Diagram ----------------------------------27
11.2. Camera/System Control Circuit Block
Diagram----------------------------------------------------- 28
11.3. Video/Audio Signal Process Circuit Block
Diagram----------------------------------------------------- 29
11.4. Lens Drive Circuit Block Diagram -------------------- 30
11.5. Power Supply Circuit Block Diagram---------------- 31
12 Wiring Connection Diagram --------------------------------- 32
12.1. Interconnection Diagram ------------------------------- 32
3
1 Safety Precautions
1.1. General Guidelines
1. IMPORTANT SAFETY NOTICE
There are special components used in this equipment
which are important for safety. These parts are marked by
in the Schematic Diagrams, Circuit Board Layout,
Exploded Views and Replacement Parts List. It is essential that these critical parts should be replaced with manufacturer’s specified parts to prevent X-RADIATION,
shock, fire, or other hazards. Do not modify the original
design without permission of manufacturer.
2. An Isolation Transformer should always be used during
the servicing of AC Adaptor whose chassis is not isolated
from the AC power line. Use a transformer of adequate
power rating as this protects the technician from accidents resulting in personal injury from electrical shocks. It
will also protect AC Adaptor from being damaged by accidental shorting that may occur during servicing.
3. When servicing, observe the original lead dress. If a short
circuit is found, replace all parts which have been overheated or damaged by the short circuit.
4. After servicing, see to it that all the protective devices
such as insulation barriers, insulation papers shields are
properly installed.
5. After servicing, make the following leakage current
checks to prevent the customer from being exposed to
shock hazards.
1.2. Leakage Current Cold Check
1. Unplug the AC cord and connect a jumper between the
two prongs on the plug.
2. Measure the resistance value, with an ohmmeter,
between the jumpered AC plug and each exposed metallic cabinet part on the equipment such as screwheads,
connectors, control shafts, etc. When the exposed metallic part has a return path to the chassis, the reading
should be between 1 MΩ and 5.2 MΩ. When the exposed
metal does not have a return path to the chassis, the
reading must be infinity.
1.3. Leakage Current Hot Check
(See Figure 1.)
1. Plug the AC cord directly into the AC outlet. Do not use
an isolation transformer for this check.
2. Connect a 1.5 kΩ, 10 W resistor, in parallel with a 0.15 μF
capacitor, between each exposed metallic part on the set
and a good earth ground, as shown in Figure 1.
3. Use an AC voltmeter, with 1 kΩ/V or more sensitivity, to
measure the potential across the resistor.
4. Check each exposed metallic part, and measure the voltage at each point.
5. Reverse the AC plug in the AC outlet and repeat each of
the above measurements.
6. The potential at any point should not exceed 0.75 V RMS.
A leakage current tester (Simpson Model 229 or equivalent) may be used to make the hot checks, leakage current must not exceed 1/2 mA. In case a measurement is
outside of the limits specified, there is a possibility of a
shock hazard, and the equipment should be repaired and
rechecked before it is returned to the customer.
Figure. 1
4
2Warning
2.1. Prevention of Electrostatic Discharge (ESD) to Electrostatically
Sensitive (ES) Devices
Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called Electrostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field-effect transistors and
semiconductor "chip" components. The following techniques should be used to help reduce the incidence of component damage
caused by electrostatic discharge (ESD).
1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any ESD on your
body by touching a known earth ground. Alternatively, obtain and wear a commercially available discharging ESD wrist strap,
which should be removed for potential shock reasons prior to applying power to the unit under test.
2. After removing an electrical assembly equipped with ES devices, place the assembly on a conductive surface such as aluminum foil, to prevent electrostatic charge buildup or exposure of the assembly.
3. Use only a grounded-tip soldering iron to solder or unsolder ES devices.
4. Use only an antistatic solder removal device. Some solder removal devices not classified as "antistatic (ESD protected)" can
generate electrical charge sufficient to damage ES devices.
5. Do not use freon-propelled chemicals. These can generate electrical charges sufficient to damage ES devices.
6. Do not remove a replacement ES device from its protective package until immediately before you are ready to install it. (Most
replacement ES devices are packaged with leads electrically shorted together by conductive foam, aluminum foil or comparable conductive material).
7. Immediately before removing the protective material from the leads of a replacement ES device, touch the protective material
to the chassis or circuit assembly into which the device will be installed.
CAUTION :
Be sure no power is applied to the chassis or circuit, and observe all other safety precautions.
8. Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise harmless motion such as the
brushing together of your clothes fabric or the lifting of your foot from a carpeted floor can generate static electricity (ESD) sufficient to damage an ES device).
2.2. How to Recycle the Lithium Ion Battery (U.S. Only)
5
2.3. How to Replace the Lithium Battery
2.3.1. Replacement Procedure
1. Remove the SD Holder P.C.B.. (Refer to Disassembly Procedures.)
2. Unsolder the each soldering point of electric lead terminal for Lithium battery (Ref. No. “B6401” at foil side of SD HOLDER
P.C.B.) and remove the Lithium battery together with electric lead terminal. Then replace it into new one.
NOTE:
The Type No. ML-614S/DN includes electric lead terminals.
NOTE:
This Lithium battery is a critical component.
(Type No.: ML-614S/DN Manufactured by Energy Company, Panasonic Corporation)
It must never be subjected to excessive heat or discharge.
It must therefore only be fitted in requirement designed specifically for its use.
Replacement batteries must be of same type and manufacture.
They must be fitted in the same manner and location as the original battery, with the correct polarity contacts observed.
Do not attempt to re-charge the old battery or re-use it for any other purpose.
It should be disposed of in waste products destined for burial rather than incineration.
NOTE:
Above caution is applicable for a battery pack which is for HC-V10/V10M/V11M series, as well.
6
3 Service Navigation
3.1. Introduction
This service manual contains technical information, which allow service personnel’s to understand and service this model.
Please place orders using the parts list and not the drawing reference numbers.
If the circuit is changed or modified, the information will be followed by service manual to be controlled with original service manual.
3.2. General Description About Lead Free Solder (PbF)
The lead free solder has been used in the mounting process of all electrical components on the printed circuit boards used for this
equipment in considering the globally environmental conservation.
The normal solder is the alloy of tin (Sn) and lead (Pb). On the other hand, the lead free solder is the alloy mainly consists of tin
(Sn), silver (Ag) and Copper (Cu), and the melting point of the lead free solder is higher approx.30°C (86°F) more than that of the
normal solder.
Distinction of P.C.B. Lead Free Solder being used
Service caution for repair work using Lead Free Solder (PbF)
• The lead free solder has to be used when repairing the equipment for which the lead free solder is used.
(Definition: The letter of “PbF” is printed on the P.C.B. using the lead free solder.)
• To put lead free solder, it should be well molten and mixed with the original lead free solder.
• Remove the remaining lead free solder on the P.C.B. cleanly for soldering of the new IC.
• Since the melting point of the lead free solder is higher than that of the normal lead solder, it takes the longer time to melt the
lead free solder.
• Use the soldering iron (more than 70W) equipped with the temperature control after setting the temperature at 350±30°C
(662±86°F).
Recommended Lead Free Solder (Service Parts Route.)
• The following 3 types of lead free solder are available through the service parts route.
RFKZ03D01KS-----------(0.3mm 100g Reel)
RFKZ06D01KS-----------(0.6mm 100g Reel)
RFKZ10D01KS-----------(1.0mm 100g Reel)
Note
* Ingredient: tin (Sn) 96.5%, silver (Ag) 3.0%, Copper (Cu) 0.5%, Cobalt (Co) / Germanium (Ge) 0.1 to 0.3%
3.3. Important Notice 1:(Other than U.S.A. and Canadian Market)
1. The service manual does not contain the following information, because of the impossibility of servicing at component level
without concerned equipment/facilities.
a. Schematic diagram, Block Diagram and P.C.B. layout of MAIN P.C.B..
b. Parts list for individual parts for MAIN P.C.B..
When a part replacement is required for repairing MAIN P.C.B., replace as an assembled parts. (Main P.C.B.)
2. The following category is /are recycle module part. Please send it/them to Central Repair Center.
• MAIN P.C.B. (VEP03J59CN: HC-V10P/PC/PU/GT)
• MAIN P.C.B. (VEP03J59CP: HC-V10EB/EC/EE/EF/EG/EP/GA/GC/GK/GN/GW)
• MAIN P.C.B. (VEP03J59AN: HC-V10MPU, V11MPU)
7
3.4. How to Define the Model Suffix (NTSC or PAL model)
There are seven kinds of HC-V10/V10M/V11M.
• a) HC-V10P
• b) HC-V10PC
• c) HC-V10EB/EC/EF/EG/EP/GN
• d) HC-V10EE
• e) HC-V10GK
• f) HC-V10GT
• g) HC-V10PU/GA/GC/GW, V10MPU, V11MPU
What is the difference is that the “INITIAL SETTING” data which is stored in Flash ROM mounted on Main P.C.B..
3.4.1. Defining methods:
To define the model suffix to be serviced, refer to the rating label and caution label which are putted on the Unit.
NOTE:
After replacing the MAIN P.C.B., be sure to achieve adjustment.
The adjustment instruction is available at “software download” on the “Support Information from NWBG/VDBG-AVC” web-site in
“TSN system”, together with Maintenance software.
8
3.5. Formatting
9
4 Specifications
10
11
5 Location of Controls and Components
1 LCD monitor
●
It can open up to 90Q.
●
It can rotate up to 180Q towards the lens
or 90Qtowards the opposite direction.
2 Intelligent auto/Manual button
[iA/MANUAL]
3 Optical image stabilizer button
[ O.I.S.]
4 Power button [ ]
5 Delete button [ ]
6 Audio-video output terminal [A/V]
●
Use the AV cable (only the supplied
cable).
7 USB terminal [ ]
8 Access lamp [ACCESS]
9SDcardslot
10 SD card cover [SD CARD]
1 23
45 678
10
9
Due to limitations in LCD production
technology, there may be some tiny bright
or dark spots on the LCD monitor screen.
However, this is not a malfunction and
does not affect the recorded picture.
11 Lens cover
12 Lens
13 Lens cover opening/closing switch
When not using the unit, close the lens
cover to protect the lens.
●
Slide the opening/closing switch to
open/close the cover.
14 Internal stereo microphones
15 Menu button [MENU]
16 Status indicator
17 Mode switch
18 Recording start/stop button
19 Cursor button
●
Use the cursor button to select the
recording functions and playback
operations, and to operate the menu
screen.
20 Enter button [ENTER]
21 Battery holder
12
13
14
11
1715
18
219102
16
12
22 Battery release lever [BATTERY]
23 Tripod receptacle
●
If you attach a tripod which has a 5.5 mm
(0.22 S) screw or larger, it may damage
this unit.
24 Photoshot button [ ]
25 Zoom lever [W/T] (In Recording
Mode)
Thumbnail display switch [ / ]/
Volume lever [UVOLT] (In Playback
Mode)
26 Speaker
27 Grip belt
Adjust the length of the grip belt so that it fits
your hand.
Flip the belt.
Adjust the length.
Replace the belt.
28 HDMI mini connector
22 23
2524
27
26
28
Change the mode to recording or playback.
Operate the mode switch to change the mode to or .
Selecting a mode
Recording Mode
Playback Mode
13
6 Service Mode
1. Indication method of the service menu
Set the mode switch “Recording” mode.
2. Turn the power on, and then while keep pressing the “Zoom lever” to W side, “Intelligent auto/Manual” button and “Menu” button for more than 3 seconds until the top screen of the Service Mode Menu being displayed.
Lock search history indication
• Display the camera system error cord for three histories saved in EEPROM
• The error cord contents which are displayed
Service mode menu
NOTE:
Do not using service mode except above table of Service mode menu.
3. End method of the top screen of the service mode menu
Press the [MENU] button to end the service mode, and then POWER OFF.
Error code Function
51 Focus control is abnormal
52 Zoom control is abnormal
53 OIS lens control is abnormal
Screen display Contents Function
1 Factory settings Function to throw a product up in a factory shipment state
(Even if recorded data exists in the build-in memory, factory
settings perform the initialization of build-in memory and clear
the history data.)
4 History display Display accumulated operating time, total recording time and
accumulated number of photos taken.
14
6.1. History Display
Press the “[UP] or [DOWN] of cursor” button for the item No. [4] is yellow high lighted, then press “ENTER” button to display the unit
histories.
Operation specifications
Indication contents
• Display the total operating time (in power on and EE state), total movie recording time and total number of photo taken. (They are
stored in EEPROM).
Press “MENU” button then return to normal recording mode.
Item Contents
PWR Total elapsed time
EE Total working time of camera sensor
REC SD Movie recorded time of inserted SD card
PICT SD Picture recorded number of inserted SD card
REC ESD Movie recorded time of internal memory
PICT ESD Picture recorded number of internal memory
15
7 Service Fixture & Tools
7.1. When Replacing the Main P.C.B.
After replacing the MAIN P.C.B., be sure to achieve adjustment.
The adjustment instruction is available at “software download” on the “Support Information from NWBG/VDBG-AVC” web-site in
“TSN system”, together with Maintenance software.
7.2. Service Position
This Service Position is used for checking and replacing parts. Use the following Extension cables for servicing.
Table S1 Extension Cable List
No. Parts No. Connection Form
1 VFK1978 FP6001(MAIN) - MONITOR FPC 31PIN 0.3 FFC
2 VFK1950 PP6008(MAIN) - LENS UNIT 33PIN 0.3 FFC
3 RFKZ0361 FP301(MAIN) - MOS UNIT 28PIN 0.5 FFC
4 RFKZ0379 PP6002(MAIN) - FP6701(DC BATT OP FPC) 40PIN 0.5 B to B
16
8 Disassembly and Assembly Instructions
8.1. Disassembly Flow Chart for the Unit
This is a disassembling chart.
When assembling, perform this chart conversely.
8.2. PCB Location
17
8.3. Disassembly Procedure for the Unit
8.3.1. Removal of the Grip Cover Unit
Fig. D1
No. Item Fig Removal
1 Grip Cover Unit Fig. D1 6 Screws (A)
Fig. D2 4 Locking tabs
Grip Cover Unit
2 Rear-Top Unit Fig. D3 4 Screws (B)
Fig. D4 1 Locking tab
Connector
Rear-Top Unit
3 Front Case Unit Fig. D5 2 Screws (C)
1 Screw (D)
FP6003 (Flex)
1 Rib
Fig. D6 1 Locking tab
Front Case Unit
4 Side-L Angle Fig. D7 1 Screw (E)
3 Screws (F)
Side-L Angle
5 Lens Unit Fig. D8 1 Screw (G)
FP301 (Flex)
FP6008 (Flex)
2 Projection Parts
Lens Unit
Fig. D9 NOTE: (When Installing)
6 SD Holder P.C.B. Fig. D10 FP6004 (Flex)
1 Screw (H)
SD Holder P.C.B.
7 MAIN P.C.B.
(HC-V10 only)
Fig. D11 2 Screws (I)
FP6001 (Flex)
Main P.C.B.
8 MAIN P.C.B.,
ESD P.C.B.
(HC-V10M/V11M only)
Fig. D12 1 Screw (J)
FP6001 (Flex)
2 Screws (K)
Fig. D13 FP6002 (Flex)
Main P.C.B.
2 Screws (L)
ESD P.C.B.
9 LCD Unit Fig. D14 1 Screw (M)
Fig. D15 1 Screw (N)
7 Locking tabs
Fig. D16 FP901 (Flex)
LCD Unit
10 Monitor P.C.B. Fig. D17 1 Screw (O)
LCD Frame
FP902 (Flex)
FP904 (Flex)
Fig. D18 3 Locking tabs
1 Hanging part
1 Locking tab
Monitor P.C.B.
18
Fig. D2
8.3.2. Removal of the Rear-Top Unit
Fig. D3
Fig. D4
8.3.3. Removal of the Front Case Unit
Fig. D5
Loading...