Panasonic HC-V100MGK, HC-V100PC, HC-V100MP, HC-V100EG, HC-V100GC User Manual

...

ORDER NO. VM1202003CE

High Definition Video Camera

Model No. HC-V100P

HC-V100PC HC-V100PU HC-V100EB HC-V100EC HC-V100EE HC-V100EF

B27

HC-V100EG HC-V100EP HC-V100GC HC-V100GK HC-V100GN HC-V100GW HC-V100MP HC-V100MPC HC-V100MPU HC-V100MGK

Colour [ HC-V100 ]

(K)...........Black Type

(W)..........White Type (only EB/EC/EE/EG/EP/GK)

[ HC-V100M ]

(K)...........Black Type

TABLE OF CONTENTS

PAG E PAG E

1 Safety Precautions -----------------------------------------------3

1.1. General Guidelines ----------------------------------------3

1.2. Leakage Current Cold Check ---------------------------3

1.3. Leakage Current Hot Check (See Figure 1.) --------3

2Warning--------------------------------------------------------------4

2.1. Prevention of Electrostatic Discharge (ESD) to Electrostatically Sensitive (ES) Devices ----------4

2.2. How to Recycle the Lithium Ion Battery (U.S. Only)-----------------------------------------------------------4

2.3. Caution for AC Cord (For EB/GC) ---------------------5

2.4. How to Replace the Lithium Battery -------------------6

3 Service Navigation------------------------------------------------7

3.1. Introduction --------------------------------------------------7

3.2. General Description About Lead Free Solder (PbF) ----------------------------------------------------------7

3.3. Important Notice 1:(Other than U.S.A. and Canadian Market) ------------------------------------------7

3.4. How to Define the Model Suffix (NTSC or PAL model)---------------------------------------------------------8

3.5. Formatting----------------------------------------------------9

4 Specifications ---------------------------------------------------- 10 5 Location of Controls and Components------------------ 12 6 Service Mode ----------------------------------------------------- 14

6.1. History Display -------------------------------------------- 15

7 Service Fixture & Tools --------------------------------------- 16

7.1. When Replacing the Main P.C.B. -------------------- 16

7.2. Service Position ------------------------------------------ 16

8 Disassembly and Assembly Instructions --------------- 17

8.1. Disassembly Flow Chart for the Unit ---------------- 17

8.2. PCB Location---------------------------------------------- 17

8.3. Disassembly Procedure for the Unit ---------------- 17

9 Measurements and Adjustments -------------------------- 24

9.1. Electric Adjustment --------------------------------------24

10 Factory Setting--------------------------------------------------- 26

10.1. How To Turn On The Factory Settings? ------------ 26

10.2. What Is The Factory Settings? ----------------------- 26

11 Block Diagra m --------------------------------------------------- 27

11.1. Overall Block Diagram ----------------------------------27

11.2. Camera/System Control Circuit Block Diagram----------------------------------------------------- 28

11.3. Video/Audio Signal Process(1) Circuit Block Diagram----------------------------------------------------- 29

11.4. Video/Audio Signal Process(2) Circuit Block Diagram----------------------------------------------------- 30

11.5. Lens Drive Circuit Block Diagram -------------------- 31

11.6. Power Supply Circuit Block Diagram---------------- 32

12 Wiring Connection Diagram --------------------------------- 33

12.1. Interconnection Diagram ------------------------------- 33

1 Safety Precautions

1.1. General Guidelines

1. IMPORTANT SAFETY NOTICE There are special components used in this equipment which are important for safety. These parts are marked by

in the Schematic Diagrams, Circuit Board Layout, Exploded Views and Replacement Parts List. It is essential that these critical parts should be replaced with manufacturer’s specified parts to prevent X-RADIATION, shock, fire, or other hazards. Do not modify the original design without permission of manufacturer.

2. An Isolation Transformer should always be used during the servicing of AC Adaptor whose chassis is not isolated from the AC power line. Use a transformer of adequate power rating as this protects the technician from accidents resulting in personal injury from electrical shocks. It will also protect AC Adaptor from being damaged by accidental shorting that may occur during servicing.

3. When servicing, observe the original lead dress. If a short circuit is found, replace all parts which have been overheated or damaged by the short circuit.

4. After servicing, see to it that all the protective devices such as insulation barriers, insulation papers shields are properly installed.

5. After servicing, make the following leakage current checks to prevent the customer from being exposed to shock hazards.

1.3. Leakage Current Hot Check (See Figure 1.)

1. Plug the AC cord directly into the AC outlet. Do not use an isolation transformer for this check.

2. Connect a 1.5 kΩ, 10 W resistor, in parallel with a 0.15 μF capacitor, between each exposed metallic part on the set and a good earth ground, as shown in Figure 1.

3. Use an AC voltmeter, with 1 kΩ/V or more sensitivity, to measure the potential across the resistor.

4. Check each exposed metallic part, and measure the voltage at each point.

5. Reverse the AC plug in the AC outlet and repeat each of the above measurements.

6. The potential at any point should not exceed 0.75 V RMS. A leakage current tester (Simpson Model 229 or equivalent) may be used to make the hot checks, leakage current must not exceed 1/2 mA. In case a measurement is outside of the limits specified, there is a possibility of a shock hazard, and the equipment should be repaired and rechecked before it is returned to the customer.

1.2. Leakage Current Cold Check

1. Unplug the AC cord and connect a jumper between the two prongs on the plug.

2. Measure the resistance value, with an ohmmeter, between the jumpered AC plug and each exposed metallic cabinet part on the equipment such as screwheads, connectors, control shafts, etc. When the exposed metallic part has a return path to the chassis, the reading should be between 1 MΩ and 5.2 MΩ. When the exposed metal does not have a return path to the chassis, the reading must be infinity.

Figure. 1

2Warning

2.1. Prevention of Electrostatic Discharge (ESD) to Electrostatically Sensitive (ES) Devices

Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called Electrostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field-effect transistors and semiconductor "chip" components. The following techniques should be used to help reduce the incidence of component damage caused by electrostatic discharge (ESD).

1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any ESD on your body by touching a known earth ground. Alternatively, obtain and wear a commercially available discharging ESD wrist strap, which should be removed for potential shock reasons prior to applying power to the unit under test.

2. After removing an electrical assembly equipped with ES devices, place the assembly on a conductive surface such as aluminum foil, to prevent electrostatic charge buildup or exposure of the assembly.

3. Use only a grounded-tip soldering iron to solder or unsolder ES devices.

4. Use only an antistatic solder removal device. Some solder removal devices not classified as "antistatic (ESD protected)" can generate electrical charge sufficient to damage ES devices.

5. Do not use freon-propelled chemicals. These can generate electrical charges sufficient to damage ES devices.

6. Do not remove a replacement ES device from its protective package until immediately before you are ready to install it. (Most replacement ES devices are packaged with leads electrically shorted together by conductive foam, aluminum foil or comparable conductive material).

7. Immediately before removing the protective material from the leads of a replacement ES device, touch the protective material to the chassis or circuit assembly into which the device will be installed.

CAUTION :

Be sure no power is applied to the chassis or circuit, and observe all other safety precautions.

8. Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise harmless motion such as the brushing together of your clothes fabric or the lifting of your foot from a carpeted floor can generate static electricity (ESD) sufficient to damage an ES device).

2.2. How to Recycle the Lithium Ion Battery (U.S. Only)

2.3. Caution for AC Cord (For EB/GC)

2.3.1. Information for Your Safety

IMPORTANT

Your attention is drawn to the fact that recording of prerecorded tapes or discs or other published or broadcast material may infringe copyright laws.

WARNING

To reduce the risk of fire or shock hazard, do not expose this equipment to rain or moisture.

CAUTION

To reduce the risk of fire or shock hazard and annoying interference, use the recommended accessories only.

FOR YOUR SAFETY

DO NOT REMOVE THE OUTER COVER

To prevent electric shock, do not remove the cover. No user serviceable parts inside. Refer servicing to qualified service

personnel.

2.3.2. Caution for AC Mains Lead

For your safety, please read the following text carefully.

This appliance is supplied with a moulded three-pin mains plug for your safety and convenience. A 5-ampere fuse is fitted in this plug. Should the fuse need to be replaced please ensure that the replacement fuse has a rating of 5 amperes and it is approved by ASTA or BSI to BS1362 Check for the ASTA mark or the BSI mark on the body of the fuse.

2.3.2.1. Important

The wires in this mains lead are coloured in accordance with the following code:

Blue Neutral Brown Live

As the colours of the wires in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows:

The wire which is coloured BLUE must be connected to the terminal in the plug which is marked with the letter N or coloured BLACK.

The wire which is coloured BROWN must be connected to the terminal in the plug which is marked with the letter L or coloured RED.

Under no circumstances should either of these wires be connected to the earth terminal of the three pin plug, marked with the letter E or the Earth Symbol.

2.3.2.2. Before Use

Remove the Connector Cover as follows.

If the plug contains a removable fuse cover you must ensure that it is refitted when the fuse is replaced. If you lose the fuse cover, the plug must not be used until a replacement cover is obtained. A replacement fuse cover can be purchased from your local Panasonic Dealer.

If the fitted moulded plug is unsuitable for the socket outlet in your home then the fuse should be removed and the plug cut off and disposed of safety. There is a danger of severe electrical shock if the cut off plug is inserted into any 13-ampere socket.

If a new plug is to be fitted please observe the wiring code as shown below. If in any doubt, please consult a qualified electrician.

2.3.2.3. How to Replace the Fuse

1. Remove the Fuse Cover with a screwdriver.

2. Replace the fuse and attach the Fuse cover.

2.4. How to Replace the Lithium Battery

2.4.1. Replacement Procedure

1. Remove the SD Holder P.C.B.. (Refer to Disassembly Procedures.)

2. Unsolder the each soldering point of electric lead terminal for Lithium battery (Ref. No. “B6401” at foil side of SD HOLDER P.C.B.) and remove the Lithium battery together with electric lead terminal. Then replace it into new one.

NOTE:

The Type No. ML-614S/DN includes electric lead terminals.

NOTE:

This Lithium battery is a critical component. (Type No.: ML-614S/DN Manufactured by Energy Company, Panasonic Corporation) It must never be subjected to excessive heat or discharge. It must therefore only be fitted in requirement designed specifically for its use. Replacement batteries must be of same type and manufacture. They must be fitted in the same manner and location as the original battery, with the correct polarity contacts observed. Do not attempt to re-charge the old battery or re-use it for any other purpose. It should be disposed of in waste products destined for burial rather than incineration.

NOTE:

Above caution is applicable for a battery pack which is for HC-V100/V100M series, as well.

3 Service Navigation

3.1. Introduction

This service manual contains technical information, which allow service personnel’s to understand and service this model. Please place orders using the parts list and not the drawing reference numbers. If the circuit is changed or modified, the information will be followed by service manual to be controlled with original service manual.

3.2. General Description About Lead Free Solder (PbF)

The lead free solder has been used in the mounting process of all electrical components on the printed circuit boards used for this equipment in considering the globally environmental conservation. The normal solder is the alloy of tin (Sn) and lead (Pb). On the other hand, the lead free solder is the alloy mainly consists of tin (Sn), silver (Ag) and Copper (Cu), and the melting point of the lead free solder is higher approx.30°C (86°F) more than that of the normal solder.

Distinction of P.C.B. Lead Free Solder being used

Service caution for repair work using Lead Free Solder (PbF)

• The lead free solder has to be used when repairing the equipment for which the lead free solder is used. (Definition: The letter of “PbF” is printed on the P.C.B. using the lead free solder.)

• To put lead free solder, it should be well molten and mixed with the original lead free solder.

• Remove the remaining lead free solder on the P.C.B. cleanly for soldering of the new IC.

• Since the melting point of the lead free solder is higher than that of the normal lead solder, it takes the longer time to melt the lead free solder.

• Use the soldering iron (more than 70W) equipped with the temperature control after setting the temperature at 350±30°C (662±86°F).

Recommended Lead Free Solder (Service Parts Route.)

• The following 3 types of lead free solder are available through the service parts route. RFKZ03D01KS-----------(0.3mm 100g Reel) RFKZ06D01KS-----------(0.6mm 100g Reel) RFKZ10D01KS-----------(1.0mm 100g Reel)

Note

* Ingredient: tin (Sn) 96.5%, silver (Ag) 3.0%, Copper (Cu) 0.5%, Cobalt (Co) / Germanium (Ge) 0.1 to 0.3%

3.3. Important Notice 1:(Other than U.S.A. and Canadian Market)

1. The service manual does not contain the following information, because of the impossibility of servicing at component level without concerned equipment/facilities.

a. Schematic diagram, Block Diagram and P.C.B. layout of MAIN P.C.B.. b. Parts list for individual parts for MAIN P.C.B..

When a part replacement is required for repairing MAIN P.C.B., replace as an assembled parts. (Main P.C.B.)

2. The following category is /are recycle module part. Please send it/them to Central Repair Center.

• MAIN P.C.B. (VEP03J56CN: HC-V100P/PC/PU)

• MAIN P.C.B. (VEP03J56CP: HC-V100EB/EC/EE/EF/EG/EP/GC/GK/GN/GW)

• MAIN P.C.B. (VEP03J56AN: HC-V100MP/PC/PU)

• MAIN P.C.B. (VEP03J56AP: HC-V100MGK)

3.4. How to Define the Model Suffix (NTSC or PAL model)

There are seven kinds of HC-V100/V100M.

• a) HC-V100M (Japan domestic model)

• b) HC-V100P, V100MP

• c) HC-V100PC, V100MPC

• d) HC-V100EB/EC/EF/EG/EP/GN

• e) HC-V100EE

• f) HC-V100GK, V100MGK

• g) HC-V100PU/GC/GW, V100MPU

What is the difference is that the “INITIAL SETTING” data which is stored in Flash ROM mounted on Main P.C.B..

3.4.1. Defining methods:

To define the model suffix to be serviced, refer to the rating label and caution label which are putted on the Unit.

NOTE:

After replacing the MAIN P.C.B., be sure to achieve adjustment. The adjustment instruction is available at “software download” on the “Support Information from NWBG/VDBG-AVC” web-site in “TSN system”, together with Maintenance software.

3.5. Formatting

4 Specifications

5 Location of Controls and Components

1 Speaker 2 USB terminal [ ] 3 Intelligent auto/Manual button

[iA/MANUAL]

4 Optical image stabilizer/Delete button

[ O.I.S./ ] 5 Power button [ ] 6 HDMI mini connector [HDMI] 7 AV multi connector [AV MULTI]

●

Use the AV multi cable (only the supplied cable).

8 Battery release lever [BATT]

9 Lens cover opening/closing switch

When not using the unit, close the lens cover to protect the lens.

●

Slide the opening/closing switch to open/close the cover.

10 Lens cover 11 Lens 12 Internal stereo microphones

AV MULTI

3 4 5

867

13 Menu button [MENU] 14 Mode switch 15 Status indicator 16 Recording start/stop button 17 Cursor button

●

Use the cursor button to select the recording functions and playback operations, and to operate the menu screen.

18 Enter button [ENTER] 19 LCD monitor

●

It can open up to 90Q.

●

It can rotate up to 180Q  towards the lens or 90Q towards the opposite direction.

20 Battery holder

1413

15 16

20718191

Due to limitations in LCD production technology, there may be some tiny bright or dark spots on the LCD monitor screen. However, this is not a malfunction and does not affect the recorded picture.



21 Tripod receptacle

●

If you attach a tripod which has a 5.5 mm (0.22 S) screw or larger, it may damage this unit.

22 SD card cover 23 Access lamp [ACCESS] 24 Card slot

25 Photoshot button [ ] 26 Zoom lever [W/T] (In Recording

Mode) Thumbnail display switch [ / ]/ Volume lever [UVOLT] (In Playback Mode)

27 DC input terminal [DC IN]

●

Do not use any other AC adaptors except the supplied one.

28 Grip belt

Adjust the length of the grip belt so that it fits your hand.

 Flip the belt.  Adjust the length.  Replace the belt.

Change the mode to recording or playback.

Operate the mode switch to change the mode to or .

Selecting a mode

Recording Mode

Playback Mode

5262







6 Service Mode

1. Indication method of the service menu Set the mode switch “Recording” mode.

2. Turn the power on, and then while keep pressing the “Zoom lever” to W side, “Intelligent auto/Manual” button and “Menu” button for more than 3 seconds until the top screen of the Service Mode Menu being displayed.

Lock search history indication

• Display the camera system error cord for three histories saved in EEPROM

• The error cord contents which are displayed

Error code Function

51 Focus control is abnormal 52 Zoom control is abnormal 53 OIS lens control is abnormal

Service mode menu

Screen display Contents Function

1 Factory settings Function to throw a product up in a factory shipment state

(Even if recorded data exists in the build-in memory, factory settings perform the initialization of build-in memory and clear the history data.)

4 History display Display accumulated operating time, total recording time and

accumulated number of photos taken.

NOTE:

Do not using service mode except above table of Service mode menu.

3. End method of the top screen of the service mode menu Press the [MENU] button to end the service mode, and then POWER OFF.

6.1. History Display

Press the “[UP] or [DOWN] of cursor” button for the item No. [4] is yellow high lighted, then press “ENTER” button to display the unit histories.

Operation specifications

Indication contents

• Display the total operating time (in power on and EE state), total movie recording time and total number of photo taken. (They are stored in EEPROM).

Item Contents PWR Total elapsed time EE Total working time of camera sensor REC SD Movie recorded time of inserted SD card PICT SD Picture recorded number of inserted SD card REC ESD Movie recorded time of internal memory PICT ESD Picture recorded number of internal memory

Press “MENU” button then return to normal recording mode.

7 Service Fixture & Tools

7.1. When Replacing the Main P.C.B.

7.2. Service Position

This Service Position is used for checking and replacing parts. Use the following Extension cables for servicing.

Table S1 Extension Cable List

No. Parts No. Connection Form 1 RFKZ0487 FP6004(MAIN) - MONITOR FPC 35PIN 0.3 FFC 2 RFKZ0444 PP6001(MAIN) - PS6401(SD HOLDER) 50PIN 0.5 B to B 3 VFK1480 FP6003(MAIN) - ECM FPC(FRONT CASE UNIT) 6PIN 0.5 FFC 4 VFK1440 FP6402(SD HOLDER) - TOP OPERATION UNIT(SIDE CASE-R UNIT) 10PIN 0.5 FFC

8 Disassembly and Assembly Instructions

8.1. Disassembly Flow Chart for the Unit

This is a disassembling chart. When assembling, perform this chart conversely.

8.2. PCB Location

8.3. Disassembly Procedure for the Unit

No. Item Fig Removal

1 Top Case Unit Fig. D1 1 Screw (A)

Fig. D2 2 Screws (B)

3 Locking tabs 3 Hooking parts Top Case Unit

2 Side Case L Unit Fig. D3 1 Screw (C)

4 Screws (D)

Fig. D4 2 Locking tabs

1 Convex 1 Projection part Side Case L Unit

3 Front Case Unit Fig. D5 1 Screw (F)

1 Screw (G)

Fig. D6 FP6003 (Flex)

1 Rib Front Case Unit

4 Lens Unit Fig. D7 FP6008 (Flex)

Fig. D8 PP301 (Connector)

1 Convex Lens Unit

5 Main P.C.B.

SD Holder P.C.B.

6 ESD P.C.B.

(HC-V100M only)

7 LCD Case T Unit

LCD Unit

Fig. D9 5 Screws (H)

FP6004 (Flex) P6003 (Connector) P6401(Connector) FP6402(Flex) 2 Ribs

FP3201 (Flex) Fig. D10 NOTE: (When Installing) Fig. D11 SD Holder P.C.B.

Main P.C.B. Fig. D12 2 Screws (I)

ESD P.C.B. Fig. D13 2 Screws (J)

2 Screws (K) Fig. D14 7 Locking tabs

LCD Case T Unit

FP901 (Flex)

1 Screw (L)

1 Hooking part

LCD Unit

8.3.1. Removal of the Top Case Unit

Fig. D2

Fig. D1

8.3.2. Removal of the Side Case L Unit

Fig. D3

Fig. D4

8.3.3. Removal of the Front Case Unit

Fig. D5

+ 43 hidden pages